American Standard 2848409WRW-PKG1 Mode d'emploi

WALK-IN BATH INSTALLATION

INSTRUCTIONS AND OWNER’S MANUAL

1

CONGRATULATIONS!

You are now the owner of a walk-in bathtub from the most trusted name in plumbing.

We thank you for your purchase. Your American Standard ® walk-in bath is a true

investment in your health and peace of mind.

Customer Support: (866) 423-0800

OWNERS MANUAL

2

TABLE OF CONTENTS

UNPACKING THE UNIT………………………………………………………………. Page 3

RESPONSIBILITIES OF THE INSTALLER…………………………………………… Page 4

TESTING YOUR TUB BEFORE INSTALLATION…………………………………… Page 5

INSTALLATION PREPARATION…………………………………………………….. Page 6

ELECTRICAL INSTALLATION………………………………………………………. Page 7

INSTALLATION PROCEDURES…………………………… ………………………... Page 8-17

SAFETY INSTRUCTIONS ……………………………… ……………………………. Page 18

OPERATING INSTRUCTIONS…………………………… ………………………….. Page 19-20

CLEANING & MAINTENANCE……………………………………………………..... Page 21

WARRANTY…………………………………………………………………………..... Page 22

TROUBLESHOOTING………………………………………………………………..... Page 23-25

OWNERS MANUAL

3

UNPACKING THE UNIT

1. FIRST, inspect the carton for damage: CAREFULLY DOCUMENT AND

PHOTOGRAGH ALL PERCEIVED DAMAGE. Report all damage claims to

customer service at 1-866-423-0800.

2. DO NOT LIFT THE TUB BY THE PLUMBING

. Doing so can result in leaks, for

which the installer is responsible. All Walk-In Tubs are water tested before they

leave our factory and the bathtub you have purchased has passed inspection.

3. Immediately inspect the unit for damage even if there is no carton damage. All

product damage must be reported within 72 hours of receipt from American

Standard®. Once the unit is installed, surface damages will be assumed to be

installation-related if not reported prior to installation. Installers are also responsible

for damage that occurs once the unit is placed in its niche.

NOTE: Remove all packaging material except for the protective plastic. This has

been placed on the tub at the factory to eliminate abrasions from handling. This

should only be removed at final clean up.

4. Inspect the plumbing for any fittings that may have loosened in transit.

5. Read the following instructions completely before installing this product. If the

home-owner or installer has any questions, please call us at 1-866-423-0800.

6. You must follow all the instructions in this manual.

FAILURE TO READ AND COMPLY WITH ALL INSTRUCTIONS CAN RESULT IN

PRODUCT DAMAGE OR INJURY TO BOTH INSTALLER AND HOMEOWNER. IT

WILL ALSO RESULT IN ASSUMPTION OF ALL LIABILITY BY SAID INSTALLER.

OWNERS MANUAL

4

RESPONSIBILITIES OF THE INSTALLER

The Installer must inspect and water test the product prior to installation to ensure the unit is free of defect

and /or damage. In the event of a problem, the unit must not be installed. If the packaging or product has

been damaged, please call immediately at 1-866-423-0800.

This product has been listed by INTERTEK / ETL and IAPMO / C UPC. The product has been tested and

complies with the following standards and guidelines: IAPMO /C UPC, UL-1795, ANSI Z-124.1.2,

ASME A 112.19.7, ASME A 112.19.15 & CSA B-45. The installer is responsible for compliance to

state and local codes.

This product is designed to be installed by a licensed tradesperson. Licensed plumbers and electricians

should be employed to insure proper installation. Installer assumes all liabilities for installation

procedures.

Although American Standard® has taken reasonable precautions to ensure that the Quick Drain

TM

is

suitable for residential plumbing; it is the responsibility of the installer to insure that the plumbing is

acceptable for use of the Quick Drain

TM

. American Standard® does not accept responsibility for

damage arising from use of the Quick Drain

TM

.

Only accessories authorized by manufacturer should be used with this product.

IMPORTANT SAFETY INSTRUCTIONS

INSTRUCTIONS PERTAINING TO RISK OF FIRE,

ELECTRICAL SHOCK OR INJURY TO PERSONS

SAVE THESE INSTRUCTIONS!

WARNING! ALL INSTRUCTIONS LISTED IN THIS MANUAL SHOULD BE READ AND

FOLLOWED CAREFULLY. ALL PRECAUTIONS PERTAINING TO RISK OF FIRE,

ELECTRIC SHOCK, OR INJURY TO PERSONS MUST BE UNDERSTOOD AND

EXPLAINED TO OWNER.

TO REDUCE THE RISK OF INJURY, CHILDREN OR PERSONS WITH INFIRMITIES

MUST NOT BE PERMITTED TO USE THIS PRODUCT WITHOUT CLOSE AND

CONTINUOUS SUPERVISION.

OWNERS MANUAL

5

TESTING YOUR WALK-IN TUB BEFORE INSTALLATION

1. All American Standard® walk-in baths are 100% water tested at the factory and have passed inspection.

Transportation and mishandling may loosen fittings and cause leaks. It is therefore necessary to test the

bathtub while there is access to all sides of the bath.

2. The unit needs to be filled with water and inspected for leaks along the door as well as the whirlpool and

air systems if equipped. The inspection needs to be performed with and without the whirlpool and / or air

systems operating. It is best to test the unit outside by filling with a garden hose.

a. Place the tub on a completely flat surface in an area where it may be drained after testing.

b. Using a clean rag and warm water wipe down seal to insure it is free of debris.

c. Seal the drain hole (this can be done with tape) and fill the tub to at least three inches above the

highest jet, or to the bottom of the safety bar if no jets are present.

d. Allow the water to stand in tub for 30 minutes and then inspect all plumbing and seals for

leaks.

e. Using appropriately rated three-prong extension cords, all plugged in to separate outlets,

operate all electrical components (air blower, water pump, and heater if applicable) for another

30 minutes and inspect for leaks again. Inspect the unions around the pump and heater.

f. If a leak persists at a union after tightening, it may have been over-tightened or might have a

displaced O-ring. Disassemble it and make sure the O-ring was seated properly. Do the same if

a leak persists at the heater. Verify that the heater threads match the pipe threads.

g. Ensure that all jets are open and working, some jets are adjustable for both flow rate and

direction of flow. The jet water flow rate is adjusted by turning either the outside ring or the

inside nozzle clockwise or counterclockwise. Some jets are not adjustable at the jet face, but

can be adjust by the “Leg’s Only Massage”. The “Legs Only Massage” Valve is located near

the seat. (If equipped.) .

3. If the pump/blower/lights/heater does not operate:

a. Check the breaker to ensure that power is on and make sure that any cables and / or air lines

connecting the control boxes to the switches and pumps are firmly attached. Verify the correct

electrical circuit and amps of the electrical cord.

b. Go to Trouble Shooting Guidelines. (See pages 23-25.)

c. Do not

run any pumps unless the tub is filled with water to the proper level. Damage due to

dry operation of pumps is not covered under the warranty period. (See pg. 22.)

Failure to perform these tests before installation will make the installer liable for future repair costs.

OWNERS MANUAL

6

INSTALLATION PREPARATION

1. Check the floor area where the tub is to be installed.

a. Clean area of any debris or trash.

b. Use a 5 or 6-foot level and determine if the floor is level. If the floor is not level,

adjust all leveling feet to perfectly level the tub.

Note: It is important that all leveling feet are completely touching the floor and

level for the door system to work properly.

2. Check to ensure that the drain piping has been “roughed-in” at the proper location. See

specification sheets (installation detail) included in this manual.

3. Ensure that the proper electrical service has been installed at the pump location. See electrical

Requirements in the manual. (See page 7.)

OWNERS MANUAL

7

ELECTRICAL INSTALLATION

All electrical wiring must be installed in accordance with the National Electrical Code and with all

local codes. All wiring shall be done by a qualified electrician. Run one, two or three branch circuits

(as required) from the main electrical service panel to the pump area of the framing structure to

provide power to the unit.

Electrical components have specific wiring requirements. Refer to the matrix below for the electrical

supply requirements for the whirlpool bathtub and factory installed components.

Branch circuits must be rated for 110 – 120 volts. Use 12 Gauge, 3 conductor cable for the circuits.

If the length run exceeds 100 feet, check with local codes for requirements. Install moisture proof

junction box(s) 6” above the floor at the pump end of the framing for each circuit.

DO NOT INSTALL THE JUNCTION BOX(S) WHERE IT CAN BE REACHED WHILE SITTING OR

STANDING IN THE TUB OR TOUCHING THE FAUCETS.

QUICK DRAIN™, LIGHTS, WHIRLPOOL, AIR SPA, COMBO & HEATER

ELECTRIAL REQUIREMENTS

This section lists the factory installed components of the Whirlpool and/or Air Spa Systems.

Note the required number of circuits and their rating for the Whirlpool & Air Spa unit you are planning to install.

ELECTRICAL REQUIREMENTS FOR FACTORY INSTALLED COMPONENTS

Systems

Electrical Rating

Circuit 1

Electrical Rating

Circuit 2

Dedicated

Circuit

Soaker w / Quick Drain™ 15 Amp GFCI

Soaker w / Light 15 Amp GFCI

Soaker w / Quick Drain™ w / Light 15 Amp GFCI

Whirlpool or Air Spa 15 Amp GFCI

Whirlpool or Air Spa w / Light 15 Amp GFCI

Whirlpool or Air Spa w/ Quick Drain™ 15 Amp GFCI 15 Amp GFCI

Whirlpool or Air Spa w/ Light & Quick Drain™ 15 Amp GFCI 15 Amp GFCI

Whirlpool & Air Spa (Combo) 15 Amp GFCI 15 Amp GFCI

Whirlpool & Air Spa (Combo) w/ Light 15 Amp GFCI 15 Amp GFCI

Whirlpool & Air Spa (Combo) w/ Quick Drain™ 20 Amp GFCI 15 Amp GFCI

Whirlpool & Air Spa (Combo) w/ Light & Quick Drain™ 20 Amp GFCI 15 Amp GFCI

Whirlpool Inline Heater - Dedicated Circuit

15 Amp GFCI

All electrical connections must be carried out by a certified electrician in accordance with local electrical

requirements and codes.

OWNERS MANUAL

8

INSTALLATION PROCEDURES

▲ WARNING: When installing whirlpool massage baths, air spa baths, combo baths, or Quick Drain™

equipped baths, the following precautions must be followed:

▲ WARNING: Danger: Risk of electrical shock; connect components to separate circuits, EACH protected

by a ground fault circuit interrupter (GFCI)

▲ WARNING: Installation must provide access for servicing the pump and motor (all American

Standard® walk-in baths come with access panels for the pump, motor and faucet).

1. Install tub waste/overflow according to instructions included with the provided kits. The Gel Coat Series

requires the installation of a door drain with check valve. The check valve and tubing must be installed

horizontal to the floor. Some installations will require the purchase of additional fittings.

2. American Standard Faucet Installation # 9FHS-CH

 Review the installation instructions packed with the faucet set.

 Mask off the tub’s deck with a protective tape.

 Locate and mark the center line of the overflow fitting

 Locate and mark 1 ½” line either side of the tub’s center line to establish the overflow clearance.

 Follow the drill template and faucet installation instructions.

3. Other Faucet Model and / or Brand

 Review the installation instructions packed with the faucet set.

 Mask off the tub’s deck with a protective tape.

 Locate and mark the center line of the overflow fitting

 Locate and mark 1 ½” line either side of the tub’s center line to establish the overflow clearance.

 Verify the first two component mounting clearance on either side of the waste overflow as well as

above and below the tub’s deck.

 Verify the remaining component mounting clearance on both sides of the overflow as well as above

and below the tub’s deck.

 It is recommended the hand held shower be installed on the corner closest to the wall to prevent water

from leaking off the deck and on to the floor.

4. Install the optional in-line water heater per manufacturer’s instructions.

5. Standard Walk-In Bath Installation - After framing is complete, set product in place to check fit and make

certain that the tub can be properly leveled. (Caution: If the bathtub is not resting on all leveling feet, water

will not drain properly and this may cause the door to leak). Secure tub frame to the studs using metal

straps. (Not provided.)

5a. Fire-Rated Drywall – If fire-rated drywall is specified, the finished fire-rated wall must be in place before

the tub is installed. The dimensions of the framing structure must be increased by the thickness of fire-

rated drywall.

OWNERS MANUAL

9

INSTALLATION PROCEDURES

WARNING: Never allow the weight of the tub to be supported by wood support stringers and do not use

integral tile flange (if equipped) to screw or nail in place, as this will result in product failure and will

void the warranty.

6. Verify the product is completely level by checking tub deck surface and ensure all leveling feet are

touching the ground.

7. Electrical connection is made by simply plugging each cord into the GFCI outlet.

8. After plumbing and electrical connections have been made, the tub and door seal should be cleaned of dirt

and debris. Use warm water and a non abrasive cleaner for clean up.

9. Installation is not complete until the bathtub has been water-tested in place and does not leak.

OWNERS MANUAL

10

Alcove Installation

`

Drain Overflow

Faucet and Pump

Access Panels

IMPORTANT

Do not use tile flange to

screw or nail tub in place.

Tubs installed in an alcove installation require a raised flange to prevent water from seeping past the tub and into the wall. Tubs

without a raised flange shall be installed with a tile flange kit such as model: 9FLNG or a similar type. The flange kit is a long

plastic strip that is fits onto the rim of the tub to provide the leak protection needed.

The tile flange should be installed on the tub before it is placed in the alcove. Install the tile flange along all sides of the tub where

the wall will be. Measure to fit and miter cut the flange corners. The flange should be attached to the tub with a silicone adhesive.

Warnin

g

:

N

ever attem

p

t to nail or screw thru the tub as this will result in

p

roduct failure and will void the warrant

y

.

Non Integral Flange

Integral Flange

Model A B C D E F G

2651.11X

50 ½” 26 ¼” 37 ½” 9 ½” 11 ½” 15 ½” N/A

2848.10X

48” 28” 38” 10 ¾” 14” 16 ¾” N/A

2848.11X

48” 28” 37 ½” 10” 14½” 16” N/A

3051.11X

50 ½” 30 ½” 37 ½” 9 ½” 14½” 15 ½” N/A

3052.10X

51 ½” 29 ¾” 42” 12 ½” 14½” 17” N/A

3151.10X

50 ½” 31 ¼” 37 ½” 10” 14 ½” 15 ¾” 38”

3060.10X

59 ½” 29 ¾” 37 ½” 31 ¼” 14½” 15 ¼” 38”

3260.21X

59 ½” 32 37 11 ½” 16” 20½” N/A

OWNERS MANUAL

11

Acrylic Extension Kit Installation

The Acrylic Extension Kit is designed to accommodate all acrylic walk-in tubs to fit within a 60” alcove

pocket. The top panel measures 30” x 20” (depth x width) and the front panel 37 ½” x 20” (height x width).

The panels must be trim to fit the unit within the 60” alcove.

Step 1

 Temporary locate the tub within the alcove walls.

 Level the tub along the deck and apron.

 Measure and record the distance from the tub and apron to the adjacent alcove wall.

Steps 2, 3, & 4

 Mask off and mark the trim lines for the top and front extension panels.

 Using a high speed carbide tooth blade, cut along the trim lines

 Mark a horizontal line that is parallel to the tub’s deck along the back and adjacent wall of the alcove.

 Mark a vertical line that is parallel to tub’s apron on the adjacent wall of the alcove.

 Install three wood stringers approximately 3/8” below the horizontal and vertical lines.

 Verify the fit of the front panel and then the top panel to the alcove opening.

 Shimming may be required to achieve a level fit.

OWNERS MANUAL

12

Acrylic Extension Kit Installation

Steps 5 & 6

 Remove the tub from the alcove and install the front and then top panel with the self tapping fasteners.

Steps 7 & 8

 Apply the temporary clamps to help support the front and top panels while re-locating the tub back into

the alcove.

 Remove temporary clamps, check level, shim if necessary, and seal in panels with silicone.

OWNERS MANUAL

13

Gelcoat Extension Kit Installation

The Gel Coat Extension Kits are designed for each unit to fit within a 60” alcove packet. The top and end

panels have integral flange for easy of installation.

Step 1

Temporary locate the tub within the alcove walls.

Level the tub along the deck and apron.

Measure the distance from the tub and apron to the alcove wall.

Verify the fit of both front and top extension panels.

Step 2

Mark a horizontal line that is parallel to the tub’s deck along the back and adjacent wall of the alcove.

Mark a vertical line that is parallel to tub’s apron on the adjacent wall of the alcove.

Install three wood stringers approximately 3/8” below the horizontal and vertical lines.

OWNERS MANUAL

14

Gelcoat Extension Kit Installation

Step 3

Remove the tub from the alcove.

Install the front and then the top panel with the tub brackets.

Step 4

Apply the temporary clamps to help support the panels while re-locating the tub back into the alcove.

Remove temporary clamps, check level, shim if necessary, and seal in panels with silicone.

___ ___

OWNERS MANUAL

15

Drain Overflow Installation

Drain / Overflow Information

A drain / overflow assembly is provided with the tub must be installed on the bath, water tested

and connected to the sanitary system of the house. Some drain / overflow kits are packed with

the waste flange, strainer, overflow cover, and fasteners, packed separately within the kit to

protect the trim finish. Follow the installation instructions provided with the drain / overflow

kit. After the drain is fully installed, test the unit for proper drainage. If the unit does not drain

properly, rectify the condition before proceeding with installation. American Standard is not

responsible for the removal or re-installation costs.

Note: All gel coat models require additional installation of the door drain to the waste overflow.

Connection of the Quick Drain

 Quick Drain System requires the connection to a minimum 1 ½” sanitary drain line.

 Use UPC Approved PVC Glue, Primer, and Schedule 40 1 ½” pipe.

 Do not change or modify the location and or piping of the Back Flow Manifold

 The sanitary tee is installed directly above the drain tee with clearance not greater than 1”.

 Dry fit the drain overflow assembly to the sanitary drainage pipe and check for proper fit.

 Glue the Quick Drain Fittings, pipe and drain overflow assembly to the sanitary drainage pipe.

NOTE: Water tight installation of the waste / overflow is the installer’s responsibility. Drain leakage is

excluded from Safety Tubs warranty of this product.

We have taken reasonable precautions to ensure the Quick Drain is suitable for residential

plumbing. It is the responsibility of the installer to insure the sanitary system is acceptable for the

use of the Quick Drain. We do not accept responsibility for damage arising from the use of the

Quick Drain.

OWNERS MANUAL

16

Threshold Drain Installation

Threshold Drain Information

All gel coat walk-in bathtubs are provided with a threshold door drain. All acrylic walk-in

bathtubs feature the “Patented T5 Door System” which does not require the threshold drain.

Connection of the Door Drain

 Door Drain requires the connection to a minimum 1 ½” sanitary drain line.

 Use UPC Approved PVC Glue, Primer, and Schedule 40 1 ½” pipe.

 The door drain, check valve, and 3/8” vinyl tubing are installed on the walk-in bathtub

 The door drain coupling has an integral 3/8” barb for connection of the door drain line.

 The drain coupling must be located between the drain tee and shoe along the tub’s drain line.

 The 3/8” barb on the drain coupling must be positioned parallel to the sub floor.

 Connect the door drain assembly and drain coupling with 3/8” vinyl tubing.

 Verify the coupling barb, check valve, and 3/8” tubing are horizontal to the floor.

 Glue all components and tubing in place use PVC Glue.

OWNERS MANUAL

17

Inline Heater Installation

Whirlpool In-Line Heater

All whirlpool systems are deigned with an In-Line Heater Blank. The threads and union set on the

heater blank and heaters are specifically designed for our system. All other heaters and heater blanks

will not interchanges with our system.

The heaters are equipped with a preset pressure switch which will not allow the heater to turn on if

the pump is not running with water flowing through the whirlpool system. The heater includes an

exclusive High Limit Switch. This safety circuit will not false trip from the hot tap water. It will

turn off the heater is the thermostat fails. If your whirlpool is equipped with adjustable jets, or other

flow control systems, the pre-set pressure switch may not activate the heater. To assure proper heater

operation, all jets may need to fully open with the pump operating at or near maximum flow.

Installation of the In-Line Heater

 Verify there is a dedicated 120 volt, 15 Amp Circuit with a GFCI outlet available.

 Located the Ready Heater Fitting on the walk-in bathtub.

 Loosen the union nuts and remove the Heater Ready Fitting.

 Verify the heater and union fitting threads are the same.

 Placed the ribbed side of the gasket to the union fitting.

 Insert the heater and slowly hand tighten the union nuts to a smug fit to insure proper alignment.

 Once the heater alignment is verified, give a ¼ turn to each union nut to insure a good seal.

 Fill the tub with water and check for water leaks with and without the whirlpool pump running.

OWNERS MANUAL

18

IMPORTANT SAFETY INSTRUCTIONS

INSTRUCTIONS PERTAINING TO RISK OF FIRE,

ELECTRICAL SHOCK OR INJURY TO PERSONS

WHEN USING THIS UNIT, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED.

▲ WARNING: Risk of personal injury. Use this unit for its intended use as described in this manual. DO NOT use

attachments not recommended by the manufacturer.

▲ WARNING: Risk of personal injury. To avoid injury, exercise caution when entering or exiting your walk-in bath.

▲ WARNING: Risk of personal injury. To reduce the risk of injury, do not permit children or persons with infirmities to use

this product unless they are closely supervised at all times.

▲ WARNING: Risk of hyperthermia and possible drowning. People using medications, herbal remedies, sleep aids,

and /or having adverse medical history should consult a physician before using this product.

▲ WARNING: Risk of personal injury. Water temperatures over a 100 F (38 C) may be hazardous to your health. Check

and adjust water temperature for your personal comfort.

▲ WARNING: No food or Alcoholic Beverages. Use of your bathtub immediately after meals is not recommended. Avoid

alcohol consumption before or during the bathing. Alcoholic beverages can cause drowsiness or hyperthermia resulting in loss

of consciousness or even drowning.

▲ WARNING: Pregnancy. If you are or think you may be pregnant, consult your doctor before using the bathtub.

▲ WARNING: Risk of personal injury. Risk of electric shock; do not permit electric appliances (such as a hair dryer, lamp,

telephone, radio or television) within four feet of this bathtub.

▲ WARNING: Risk of personal injury. Never drop or insert any objects into any openings.

▲ WARNING: Risk of personal injury. Do not operate this unit without the guard over the suction fittings.

The unit must be connected only to a supply circuit that is protected by a ground-fault circuit-interrupter (GFCI). Such a

GFCI should be provided by the installer and should be tested on a routine basis. To test the GFCI, push the test button.

The GFCI should interrupt power. Push the reset button. Power should be restored. If the GFCI fails to operate in this

manner, there may be a ground current flowing, indicating the possibility of an electric shock. Do not use

this massage

bathtub. Disconnect the whirlpool bathtub and have the problem corrected by a qualified service representative before

using.

To reduce the risk of electrical shock, the dedicated electrical supply circuit(s) must be grounded. To do this,

connect the third leg of the 3-conductor wiring cable to the grounding terminal of the electrical service panel

and run continuously to the green grounding screw on the GFCI or electrical receptacle in the wiring

compartment.

OWNERS MANUAL

19

SAVE THESE INSTRUCTIONS!

OPERATING INSTRUCTIONS

1. Enter your American Standard® walk-in bath, close the door, place handle in down position, and fill

the bath to at least 2 inches above the highest jet before activating the whirlpool pump (if equipped).

Do not apply excessive pressure when placing the handle in the close position. Do not put weight

on the door when entering and exiting the tub. It is recommended to leave the door in the open

position when the tub is not in use.

2. If your American Standard® walk-in bath is equipped with Whirlpool Jets, Air Spa, or Combo system,

the pump or blower is operated by the push button switch labeled “Jets” or “Air”. Both the number of

buttons and their assorted functions vary. Do not depress the button(s) repeatedly and/or rapidly as all

function(s) are controlled electronically. It may take a few seconds before any change becomes

perceptible. Refer to massage instructions sheet for more information on the controls.

3. If your American Standard ® walk-in bath is equipped with whirlpool jets, you can adjust the

direction and flow rate of the jets to your liking by moving the nozzle for direction and turning the

outside ring or the nozzle clockwise or counterclockwise for the flow rate. Some jets are not

adjustable at the jet face, but can be adjusted by the “Legs Only Massage” valve located near the seat.

(If equipped.)

4. The Legs Only Massage (whirlpool & combo systems only) opens and closes the jets above the seat

which allows you to fill the tub half-way and operate only the lower whirlpool jets. The Legs Only

Massage valve must be closed when filling the tub half-way and operating the whirlpool. Failure to

close the valve, when filling the tub half-way will result in water shooting out of the jets above the seat

when the pump is activated. (If equipped.)

5. If your American Standard® walk-in bath is equipped with an Air Spa system, you can activate the

heated blower by pushing the push button on the deck. Push the button to turn on / off and cycle for

the various speeds.

6. If your American Standard® walk-in bath is equipped with an in-line heater, the heating element will

come on automatically, but only when the whirlpool system is turned on. This heater is designed to

extend the comfortable bathing time, but does not reheat the bath water.

7. If your American Standard® walk-in bath is equipped with the Automatic Tub Clean System - Ozone,

the system will turn on automatically when the whirlpool system is turned on.

8. If your American Standard® walk-in bath is equipped with the Quick Drain

TM

, this system has its own

dedicated pump, suction and switch to activate the drain. Simply open the traditional drain system

(turn the overflow) and then press the Quick Drain™ on/off switch to activate the drain. When the

water falls below the suction guard, press the control switch to turn the drain system off.

La page charge ...

American Standard 2848409WRW-PKG1 Mode d'emploi

Ce manuel convient également à

American Standard 2848409WRW-PKG1 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents