Norcold N62/ N82 Guide d'installation

Catégorie
Cheminées
Taper
Guide d'installation

Ce manuel convient également à

Improper installation, adjustment, alteration, service or
maintenance can cause personal injury or property damage. Refer
to this manual. For assistance or additional information, contact a
qualied installer, service agency, or the gas supplier.
FOR YOUR SAFETY
Do not store or use gasoline or other ammable vapors and liquid in the
vicinity of this or any other appliance.
FOR YOUR SAFETY
If you smell gas:
1. Open windows.
2. Don’t touch electrical switches.
3. Extinguish any open ame.
4. Immediately call your gas supplier.
For N61X models: 6 cu.ft., 2-way, R.V. refrigerators.
For N81X models: 8 cu.ft., 2-way, R.V. refrigerators.
The letter “X”, in the model numbers above, stands for a letter or numeral which means a
refrigerator option.
NORCOLD, Inc.
P.O. Box 4248
Sidney, OH 45365-4248
Part No. 635484C (02/27/2014)
English
Installation Manual
DO NOT install this refrigerator in below deck marine applications. Do not install this
refrigerator in xed indoor cabin or other dwelling applications. This refrigerator must use only
NORCOLD designed and approved outside air intake and exhaust ventilation for correct and
safe operation. Any other ventilation could cause lethal combustion exhaust fumes and/or
explosive propane gas fumes to be in the living area and/or to be below deck.
WARNING
!
WARNING
!
Installation Manual 2
Table of Contents
Safety Awareness
Safety Instructions
Safety Awareness ..................................................................................................................................................................................... 2
Safety Instructions ....................................................................................................................................................................................2
Certication and Code Requirements.......................................................................................................................................................3
Ventilation Requirements..........................................................................................................................................................................4
Key Refrigerator Dimensions....................................................................................................................................................................5
Assemble the Enclosure for the Refrigerator............................................................................................................................................5
Install the Lower and Upper Vents............................................................................................................................................................6
Install Decorative Door Panels ...............................................................................................................................................................10
Install the Refrigerator ............................................................................................................................................................................ 11
Reverse the Door Swing-Nonmetal Doors (optional) .............................................................................................................................12
Reverse the Door Swing-Metal Doors (optional) ....................................................................................................................................14
Connect the Electrical Components .......................................................................................................................................................16
Connect the 120 volts AC supply ....................................................................................................................................................16
Connect the 12 volts DC supply ......................................................................................................................................................16
Connect the Low Ambient Heater (optional) ...........................................................................................................................................17
Connect the Propane Gas Components.................................................................................................................................................17
Connect the propane gas supply system ........................................................................................................................................17
Examine the propane gas supply system for leaks ......................................................................................................................... 18
Ignition and Start Up ............................................................................................................................................................................... 18
Ignition and start up ......................................................................................................................................................................... 18
Do a test of the gas safety valve .....................................................................................................................................................19
Shut down - all models ....................................................................................................................................................................19
Display Codes ........................................................................................................................................................................................19
Fault Codes ...........................................................................................................................................................................................20
Read this manual carefully and understand the contents before you install the refrigerator.
Be aware of possible safety hazards when you see the safety alert symbol on the refrigerator and in this manual. A signal word follows
the safety alert symbol and identies the danger of the hazard. Carefully read the descriptions of these signal words to fully know their
meanings. They are for your safety.
This signal word means a hazard, which if ignored, can cause dangerous personal injury, death, or much
property damage.
This signal word means a hazard, which if ignored, can cause small personal injury or much property
damage.
- This refrigerator is not approved for use as a free standing refrigerator. It is equipped for the use of propane gas only
and can not be changed to use any other fuels (natural gas, butane, etc.).
- Incorrect installation, adjustment, alteration, or maintenance of this refrigerator can cause personal injury, property
damage, or both.
- Obey the instructions in this manual to install intake and exhaust vents.
- Do not install the refrigerator directly on carpet. Put the refrigerator on a metal or wood panel that extends the full
width and depth of the refrigerator.
WARNING
!
WARNING
!
CAUTION
!
Installation Manual 3
- Do not allow anything to touch the refrigerator cooling system.
- Propane gas can ignite and cause an explosion that can result in property damage, personal injury, or death. Do not
smoke or create sparks. Do not use an open ame to examine the propane gas supply line for leaks. Always use two
wrenches to tighten or loosen the propane gas supply line connections.
- Make sure the electrical installation obeys all applicable codes. See “Certication and Code Requirements” section.
- Do not bypass or change the refrigerators electrical components or features.
- Do not spray liquids near electrical outlets, connections, or the refrigerator components. Many liquids are electrically
conductive and can cause a shock hazard, electrical shorts, and in some cases re.
- The refrigerator cooling system is under pressure. Do not try to repair or to recharge a defective cooling system.
- The cooling system contains sodium chromate. The breathing of certain chromium compounds can cause cancer. The
cooling system contents can cause severe skin and eye burns, and can ignite and burn with an intense ame. Do not
bend, drop, weld, move, drill, puncture, or hit the cooling system.
- The rear of the refrigerator has sharp edges and corners. To prevent cuts or abrasions when working on the
refrigerator, use caution and wear cut resistant gloves.
Certication and Code Requirements
This refrigerator is certied by CSA International as meeting the
latest edition of ANSI Z21.19 / CSA 1.4 standards for installation in
mobile homes or recreational vehicles.
The refrigerator must be installed in accordance with this
“Installation Manual” in order for the Norcold limited warranty to be
in effect. In addition, the installation must conform to the following,
as applicable:
In the United States and Canada:
- Local codes, or in the absence of local codes, the National
Fuel Gas Code, ANSI Z223.1/NFPA 54, the Natural Gas and Propane installation Code, CSA B149.1, ANSI A119.2 Recreational
Vehicles Code, and CSA Z240 RV Series, Recreational Vehicles.
- A manufactured home (mobile home) installation must conform with the Manufactured Home Construction and Safety Standard,
Title 24 CFR, Part 3280 [formerly the Federal Standard for Mobile Home Construction and Safety, Title 24 (part 280), and the
current CSA Z240.4, Gas-equipped Recreational Vehicles and Mobile Housing.
- If an external power source is utilized, the appliance, when installed, must be electrically grounded in accordance with local codes
or, in the absence of local codes, the National Electrical code, and ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.2.
Parts 1 and 2.
All propane gas supply piping and ttings must obey local, state, and national codes about type and size. These components must also
obey the current NFPA 1192 section 2-4, and in Canada with the current CAN 1-6.10 Standard.
Art01290
CAUTION
!
Installation Manual 4
Ventilation Requirements
The completed installation must:
- Make sure there is sufcient intake of fresh air for combustion.
- Make sure the living space is completely isolated from the combustion system of the refrigerator.
- Make sure there is complete and unrestricted ventilation of the ue exhaust which, in gas mode, can produce carbon
monoxide. The breathing of carbon monoxide fumes can cause dizziness, nausea, or in extreme cases, death.
- Make sure the refrigerator is completely isolated from its heat generating components through the correct use of
bafes and panel construction.
Certied installation needs one lower intake vent and one upper exhaust vent. Install the vents exactly as written in this manual. Any
other installation method voids both the certication and the factory warranty of the refrigerator.
The bottom of the opening for the lower intake vent, which is also the service access door, must be even with or immediately below the
oor level. This allows any leaking propane gas to escape to the outside and not to collect at oor level.
CSA International certication allows the refrigerator to have zero (0) inch minimum clearance at the sides, rear, top, and bottom. While
there are no maximum clearances specied for certication, the following maximum clearances are necessary for correct refrigerator
performance:
Bottom 0 inch min. 0 inch max.
Each Side 0 inch min 1/2 inch max.
Top 0 inch min. 1/4 inch max.
Rear 0 inch min. 1 inch max.
These clearances plus the lower and upper vents cause the natural air draft that is necessary for good refrigeration. Cooler air comes
in through the lower vent, goes up around the refrigerator coils where it removes the excess heat from the refrigerator components, and
goes out through the upper vent. If this air ow is blocked or decreased, the refrigerator will not cool correctly.
Each NORCOLD model is certied by CSA International for correct ventilation. Install only the certied vents that are listed in this
manual.
WARNING
!
Installation Manual 5
Key Refrigerator Dimensions
These key refrigerator dimensions are for your
reference as necessary (See Art01733).
Refrigerator cabinet width w/o trim:
23.47 in. max. .................................................. 1
Refrigerator width overall w/ trim:
24.6in............................................................... 2
Refrigerator cabinet to side trim:
0.80 in.............................................................. 3
Refrigerator cabinet height w/o trim:
N600 models - 52.85 in. max. ......................... 4
N800 models - 59.85 in. max. ......................... 4
Refrigerator height overall w/ trim:
N600 models - 54.5 in. .................................... 5
N800 models - 61.5 in. .................................... 5
Refrigerator cabinet to top/bottom trim:
0.93 in.............................................................. 6
Enclosure wall to hinges:
1.10 in.............................................................. 7
Refrigerator cabinet to center of handles:
N600 models - 32.5 in. .................................... 8
N800 models - 39.5 in. .................................... 8
Art01733
1
8
7
5
6
4
3
2
Assemble the Enclosure for the Refrigerator
1. Make sure the enclosure is 59.88 - 60.01 inches high for N81X models or 52.88 - 53.01 inches high for N61X models x 23.50 -
23.63 inches wide x 24 inches deep.
2. Make sure the oor is solid and level.
- The oor must be metal or a wood panel and extend the full width and depth of the enclosure.
- The oor must be able to support the weight of the refrigerator and its contents.
3. Make sure there are no adjacent heat sources such as a furnace vent, a hot water heater vent, etc.
Installation Manual 6
Install the Lower and Upper Vents
1. Using the following chart, decide which vents and rough opening (RO) sizes to use:
Certied Vent P/N RO Height RO Width
Upper Roof Exhaust Cap 622293 N/A N/A
Upper Roof Exhaust Vent 616319 24 in. 5 1/4 in.
Lower Metal Intake 616010 13 5/8 in. 21 5/8 in.
Upper Exhaust & Lower Intake Plastic 621156 13 3/4 in. 21 1/2 in.
2. Install the lower intake vent (See Art01598, Art01599, and Art01602):
The lower intake vent is also the service access opening for the components
on the rear of the refrigerator.
Make sure the bottom of the opening of the lower intake vent is
even with or immediately below the oor level. This allows any
leaking propane gas to escape to the outside and not to collect at
oor level.
- Make sure the bottom of the opening of the lower intake vent [9] is even with or
immediately below the oor level.
- Align the lower intake vent vertically below the coils [10] and the condenser [11] of the
refrigerator.
4. If there is more than 1/2 inch between either side of the refrigerator and the inside of the enclosure:
- Fill the space with berglass insulation or add a bafe to eliminate the excess clearance.
- Make sure that the rear of the batt-type insulation is between 18 - 19 inches from the face of the enclosure.
- Securely attach the batt-type insulation to the enclosure so that it remains in this position during refrigerator installation, if it
becomes wet, and in windy conditions.
10
11
9
Art01602
NOTICE
WARNING
!
Installation Manual 7
3. Install the upper exhaust vent:
Make sure that no sawdust, insulation, or other construction debris is on the refrigerator or in the enclosure.
Debris can cause a combustion hazard and prevent the refrigerator from operating correctly.
Tighten the screws of the upper roof exhaust cap to 10 inch-pounds max. Also make sure that the air ow around the
upper roof exhaust cap is not blocked or decreased by other roof mounted features such as a luggage carrier, an air
conditioner, a solar panel, etc.
- If the design of the vehicle allows, install the roof exhaust vent [12] directly above the condenser [11] of the refrigerator (See
Art01598).
- Install a bafe [13] to prevent stagnant hot air in the area [14] above the refrigerator.
- Make sure there is less than 1/4 inch clearance [715] between the bafe and the top of the refrigerator.
- Make sure the bafe is the full width of the inside of the enclosure.
- If the design of the vehicle does not allow you to install the roof exhaust vent directly above the condenser [11] of the refrigerator
(See Art01599).
- Align the roof exhaust vent [12] above the condenser [11] of the refrigerator and move it inboard as necessary.
Art01598
14
9
11
12
13
15
16
10
17
18
15
15
16
Art01599
20
14
13
12
11
16
9
10
18
17
19
16
19
CAUTION
!
NOTICE
Installation Manual 8
- Install two bafes [13] to prevent stagnant hot air in the area [14] above the refrigerator.
- Make sure the bafes are the full width of the inside of the enclosure.
- Make sure that the bafes are no more than 45° from vertical [20].
- Put one bafe between the top rear edge of the refrigerator and the inside edge of the upper exhaust vent opening.
- Put the other bafe between the outside edge of the upper exhaust vent opening and the side wall of the vehicle.
- If the depth of the enclosure is 24 inches or more and is less than 25 inches, no bafes are necessary at the rear of the enclosure.
- If the depth of the enclosure is 25 inches or more and is less than 26 inches, add two bafes [16] to the rear of the enclosure (See
Art01598 and Art01599).
- Put one bafe 18 inches to 18 1/2 inches above the bottom of the enclosure [17] (4 1/4 inches to 4 3/4 inches above the top of
the lower intake vent opening REF) [18].
- Put the other bafe at the lowest edge of the condenser [11] of the refrigerator.
- Make sure that the bafes are 1 inch or less [19] from the coils [10] and condenser of the refrigerator.
- Make sure that the bafes are the full width of the inside of the enclosure.
- If the depth of the enclosure is more than 26 inches, install a wood or an aluminum or galvanized sheet solid box bafe [21] in the
rear of the enclosure (See Art01617 and Art01618).
- Make sure that the bottom of the solid box bafe is 18 inches to 18 1/2 inches above the bottom of the enclosure [17] (4 1/4
inches to 4 3/4 inches above the top of the lower intake vent opening REF) [18] .
Art01617
14
15
13
12
19
11
21
18
17
10
9
Art01618
14
20
12
13
11
19
21
18
17
10
9
Installation Manual 9
- Make sure that the back of the solid box bafe is perpendicular to the bottom of the
enclosure.
- Make sure that the back of the solid box bafe is either against the top of the enclosure or
against the angled bafe [13] (depending on the vehicle design).
- Make sure that the solid box bafe is one inch or less [19] from the coils [10] and
condenser of the refrigerator.
- Make sure that the solid box bafe is the full width of the inside of the enclosure.
- If the design of the vehicle does not allow you to install a roof exhaust vent, install an upper
side-wall exhaust vent.
The refrigerator is 23.7 in. min. to 24.0 in. max. from the rear of the breaker to
the rear of the condenser [22]. N61X models are 47.1 in. min. to 47.4 in. max.
from the bottom of the refrigerator to the bottom of the refrigerator condenser
[23]. N81X models are 54.1 in. min. to 54.4 in. max. from the bottom of the
refrigerator to the bottom of the refrigerator condenser [23] (See Art01601).
Only use an upper side-wall exhaust vent on refrigerator models
that are equipped with a fan. If you use an upper side-wall exhaust
vent on a refrigerator model that is not equipped with a fan, the
refrigerator cooling performance will be poor.
- Make sure the refrigerator model is equipped with a fan.
- Install the upper side-wall exhaust vent [24] (See Art01592 and Art01593).
- For N61X models, make sure the distance [25] from the bottom of the enclosure to
the top of the rough opening for the upper exhaust vent is at least 55 inches.
- For N81X models, make sure the distance [25] from the bottom of the enclosure to the top of the rough opening for the
upper exhaust vent is at least 62 inches.
- Align the upper exhaust vent [24] horizontally above the lower
intake vent [9] of the refrigerator.
- To prevent stagnant hot air in the area above the refrigerator,
install an aluminum or galvanized steel sheet bafe [13]
between the top of the refrigerator and the top of the upper
exhaust vent.
- Make sure there is less than 1/4 inch clearance between
the bafe and the top of the refrigerator and that the
bafe overlaps the refrigerator 1 inch or less.
- Make sure that the bafe is against the wall of the
vehicle at the top of the upper exhaust vent and 1/4 inch
or less from the top of the opening for the upper exhaust
vent [15].
- Make sure the bafe is the full width of the inside of the
enclosure.
- When using an upper side-wall exhaust vent:
- If the depth of the enclosure is 24 inches or more and is less than
26 inches [27], install a bent aluminum or galvanized steel sheet
bafe [26] to the rear of the enclosure (See Art01592).
22
23
Art01601
Art01592
16
15
17
17
213
21
14
13
19
1
2
18
NOTICE
CAUTION
!
Installation Manual 10
The doors are made to accept decorative panels. The decorative panels must be 3/16 inch or less in thickness. Install
the decorative door panels in the refrigerator doors before installing the refrigerator in the vehicle.
- Make an upper door panel that is 21 19/32 inches wide x 14 17/32 inches high.
- Make a lower door panel that is:
- 21 19/32 inches wide and
- 31 5/8 inches high (for N6XX models) or
- 38 5/8 inches high (for N8XX models).
- Pull the panel retainer [37] off each door (See Art00965).
- Push the decorative door panel [38] into the slots of the door [39].
- Push each panel retainer into the slot on the edge of the door.
Install Decorative Door Panels
- Make sure that the bend of the bafe is the full
width of the inside of the enclosure.
- Make sure that the bend of the bafe is ush with
the bottom edge of the upper intake vent door
frame.
- Make sure that the top edge of the bafe is 1/4
inch [213] below the bottom of the condenser
and that there is 1/4 inch or less clearance [15]
between the rear of the condenser and the bafe.
- If the depth of the enclosure is more than 26 inches
[27], install a wood or an aluminum or galvanized
steel sheet solid box bafe [21] between the lower
intake vent and the upper exhaust vent (See
Art01593).
- Make sure that the solid box bafe is the full width
of the inside of the enclosure.
- Make sure that the bottom of the solid box bafe
is 18 inches to 18 1/2 inches above the bottom of
the enclosure [17] (4 1/4 inches to 4 3/4 inches
above the top of the lower intake vent opening
REF) [18] .
- Make sure that the back of the solid box bafe is
perpendicular to the bottom of the enclosure.
- Make sure that the horizontal top of the solid box
bafe is even with the bottom edge of the upper
exhaust vent [24].
- Make sure that the vertical top edge of the bafe
is between 1/4 inch [213] below the condenser and 1 1/2 inches above the bottom of the condenser.
- Make sure that there is 1/4 inch or less clearance [15] between the rear of the condenser and the bafe.
Art01593
27
17
10
9
18
25
21
24
1513
15
11
15
213
Art00965
37
38
39
NOTICE
Installation Manual 11
Put the refrigerator in position (See Art00962, Art00963, and Art00964):
Make sure the combustion seal [28] is not broken, is completely around
the refrigerator mounting anges, and is between the mounting anges
and the wall of the enclosure If the seal is not complete, exhaust fumes
can be present in the living area of the vehicle. The breathing of exhaust
fumes can cause dizziness, nausea, or in extreme cases, death.
- Push the refrigerator completely into the enclosure.
- Put the upper trim piece [40] onto the front of the refrigerator.
- Put screws [41] through the upper and lower mounting anges on the front of the refrigerator
and into the enclosure wall and oor.
- Put a cap [42] on each of the screw holes in the upper trim piece [40] on the front of the
refrigerator.
Do not omit the bottom trim piece. This piece is part of the combustion
seal.
- Push the bottom trim piece [29] onto the front of the refrigerator.
- Put two screws [41] through the trim piece, the mounting ange, and into the oor.
- Put screws through mounting ange on the rear of the refrigerator and into the oor.
Install the Refrigerator
Art00962
28
29
Art00963
41
42
40
Art00964
41
29
41
WARNING
!
WARNING
!
Installation Manual 12
Reverse the Door Swing-Nonmetal Doors (optional)
This refrigerator has cabinet hinges that allow you to change the direction the door opens
by moving the hinges on a diagonal to the opposite side.
1. Remove the doors (See Art01726):
- Remove the storage bins from the doors.
Do not mix the upper and lower hinge pins because they are different.
- Remove and save the upper hinge pin [63] from each door.
- Pull the door latch and remove each door from the refrigerator.
- Remove and save the lower hinge pin [64] from each hinge.
2. Change the position of the cabinet hinges and the strike plate (See Art01728):
- Remove and save the screws from the strike plate [65a].
- Remove the two plastic hole caps that are near the strike plate.
- Remove the L-shaped plastic covers that are opposite the hinges.
- Remove and save the screws from the upper cabinet hinge
[66a] of each door.
- Put each of these hinges on the other side of the refrigerator
as the lower hinge [66b].
- Attach each of these hinges with screws.
- Remove and save the screws from the lower cabinet hinge
[67a] of each door.
- Put each of these hinges on the other side of the refrigerator
as the upper hinge [67b].
- Attach each of these hinges with screws.
- Put the L-shaped plastic covers over the holes that were used
by the hinges.
66
Art01726
63
64
67
Art01728
66a
67a
65b
66a
66b
67a
65a
67b
67b
66b
NOTICE
Installation Manual 13
- Remove and save the screw [41] from the front box [68] (See Art01573).
- Pull the front box away from the refrigerator and out from under the controls [69].
- Reverse the front box and put it on the opposite side of the controls.
- Attach the front box to the refrigerator with the screw.
- Put the strike plate on the opposite side of the refrigerator [65b].
- Put the two round plastic caps into the holes that are near the strike plate.
3. Change the position of the door handles (See Art01727):
- Remove the screws [41] and door handle [70] from each door.
- Reverse each door handle and put the lower door handle on the upper door and the
upper door handle on the lower door.
- Attach each door handle with the screws.
4. Reinstall the doors (See Art01726):
- Turn the lower hinge pins into the lower cabinet hinges.
To prevent damage to the threads of the hinge pins, turn the hinge pins by
hand until tight and then tighten with a screwdriver.
Apply Loctite removable thread locker (blue) to the threads of the
hinge screws before assembly to prevent loosening during use.
Do not allow Loctite to contact any of the plastic surfaces of the
refrigerator because it can damage those surfaces.
- Put each door down onto the lower hinge pin.
- Align the holes in the upper hinges and hold in this position.
- Turn the upper hinge pin into the hinges of each door.
- Tighten the hinge pins.
- Put the storage bins in the doors.
Art01573
69
41
68
66
Art01726
63
64
67
41
70
Art01727
CAUTION
!
NOTICE
Installation Manual 14
Reverse the Door Swing-Metal Doors (optional)
This refrigerator has door hinges that allow you to change the direction the door opens by
moving the hinges on a diagonal to the opposite side.
1. Remove the doors (See Art00986):
- Remove the storage bins from the doors.
- Remove and save both hinge pins [71] from each door.
- Pull the door latch and remove each door away from the refrigerator.
2. Change the position of the cabinet hinges and the strike plate (See Art01728):
- Remove and save the screws from the strike plate [65a].
- Remove the two plastic hole caps that are near the strike plate.
- Remove the L-shaped plastic covers that are opposite the hinges.
- Remove and save the screws from the upper cabinet hinge [67a] of each door.
- Put each of these hinges on the other side of the refrigerator
as the lower hinge [67b].
- Attach each of these hinges with screws.
- Remove and save the screws from the lower cabinet hinge
[66a] of each door.
- Put each of these hinges on the other side of the refrigerator
as the upper hinge [66b].
- Attach each of these hinges with screws.
- Put the L-shaped plastic covers over the holes that were used
by the hinges.
- Remove and save the screw [41] from the front box [68] (See
Art01573).
- Pull the front box away from the refrigerator and out from
under the controls [69].
- Reverse the front box and put it on the opposite side of the
controls.
- Attach the front box to the refrigerator with the screw.
- Put the strike plate on the opposite side of the refrigerator
[65b].
- Put the two round plastic caps into the holes that are near the
strike plate.
71
73
66
67
74
Art00986
Art01728
66a
67a
65b
66a
66b
67a
65a
67b
67b
66b
Installation Manual 15
3. Change the position of the door handles and the door hinges (See Art01695,
Art00985, and Art00986):
- Remove the plastic cap that is opposite the upper hinge of the upper door.
- Remove the cap screws [72] from the door handle [70] and door hinge [73].
- Remove the screws [41] and door handle from each door.
- Remove the upper hinge of each door.
- Put each of these hinges on the other side of the door as the lower hinge.
- Attach each of these hinges with the cap screws that were removed from the
other side.
- The recommended torque for each cap screw [72] is 35 in.-lbs.
- Remove the lower hinge of each door.
- Put each of these hinges on the other side of the door as the upper hinge.
- Attach each of these hinges with the cap screws that were removed from the other side.
- Reverse each door handle and put the lower door handle on the upper door and the upper door
handle on the lower door.
- Attach each door handle with a cap screw [72] and screws [41].
- Put the plastic cap into the hole that is opposite the upper hinge of the upper door.
4. Reinstall the doors (See Art00986):
- Make sure each hinge bushing [74] is in the correct position.
- Put each hinge bushing into the bottom side of each door hinge.
- Put each door in the position on the refrigerator.
To prevent damage to the threads of the hinge pins, turn the hinge pins by
hand until tight and then tighten with a screwdriver.
Apply Loctite removable thread locker (blue) to the threads of the hinge
screws before assembly to prevent loosening during use. Do not
allow Loctite to contact any of the plastic surfaces of the refrigerator
because it can damage those surfaces.
- Align the hinges and put the hinge pins into each door.
- Tighten the hinge pins.
- Put the storage bins in the doors.
Art01573
69
41
68
Art01695
41
70
72
73
72
Art00985
NOTICE
CAUTION
!
Installation Manual 16
Connect the Electrical Components
AC Operation 120 volts AC voltage (132 volts max. - 108 volts min.)
12 volts DC control voltage (15.4 volts max. - 10.5 volts min.)
This refrigerator operates on these electrical sources. Operation out of these limits may damage the refrigerator’s electrical circuit
parts and will void the warranty.
The rear of the refrigerator cooling system has hot surfaces and sharp surfaces that can damage electrical
wiring. Make sure that there is a good clearance between all electrical wiring and the cooling system of the
refrigerator. Position any electrical wiring within the refrigerator enclosure opposite the burner side of the
refrigerator. Do not put any electrical wiring through the roof exhaust vent. Failure to correctly position
electrical wiring can result in electrical shock or re.
Connect the 120 volts AC supply:
Connect the AC power cord(s) only to a grounded three-prong receptacle. Do not remove the round
ground prong from any of the AC power cords. Do not use a two prong adapter or an extension cord with
any of the AC power cords. Operation of the refrigerator without correct ground can cause dangerous
electrical shock or death if you are touching the metal parts of the refrigerator.
Put the AC power cord(s) into a grounded three-prong receptacle:
- Make sure the receptacle is positioned within easy reach of the lower intake vent.
- Make sure the power cord(s) does not touch the burner cover, the ue pipe, or any hot component that could damage the insulation
of the power cord.
Connect the 12 volts DC supply:
As the distance from the vehicle battery to the refrigerator increases, the correct AWG wire size and fuse size also increases. If the
wire size is too small for the distance, a voltage drop occurs.
1. Determine the min. wire size and the max. fuse size to use:
If you use an incorrect wire size and/or fuse size, electrical re can result.
- Use a minimum of 18 AWG wire and a maximum 6 Amp fuse.
- If the wire size is larger than the min. size, use the correct fuse per RVIA A119.2 standard or local codes.
2. Install a fuse in DC power supply wires between the battery and the refrigerator:
- Put fuse as close to the battery as possible.
3. Connect the DC power supply wires (See Art00966):
- Attach a 1/4 inch Quick Connect terminal to each DC power supply wire.
Do not use the chassis of the refrigerator or the vehicle frame as one of the
conductors. Attach the DC power supply wires only to the battery and the
power board [49] of the refrigerator.
- Push the positive DC power wire [50] onto the power board terminal that is marked
12VDC.
- Push the DC ground wire [51] onto the power board terminal that is marked GND.
- Make sure each DC power supply wire is on the correct polarity terminal.
Art00966
49
50
51
121
WARNING
!
WARNING
!
WARNING
!
NOTICE
Installation Manual 17
Connect the Low Ambient Heater (optional)
Connect the low ambient heater wires to the 12 volts DC supply. The black
(+) wire of the low ambient heater is 16 AWG and the brown (-) wire is 18
AWG.
1. Cut the 12V input (+) wire behind the quick connect [269]; strip both ends
(See Art02316).
2. Solder the wires with the 16AWG black wire [266].
3. Wrap the soldered wires with black electrical tape [268]; BE SURE there
are no exposed strands.
4. Cut the 12V ground wire behind the quick connect [269]; strip both ends
(See Art02317).
5. Solder the wires with the 18AWG wire [267].
6. Wrap the soldered wires with black electrical tape [268] ; BE SURE there
are no exposed strands.
7. Connect 12V supply to the input wires.
This kit supplies DC voltage to the heater any time the
ambient temperature is low enough. Extended storage
during cold weather will drain the vehicle batteries. To
prevent battery drain, remove the 3 amp fuse from the low
ambient heater.
Art02316
268
269
266
Art02317
268
269
267
NOTICE
Connect the Propane Gas Components
This refrigerator operates on propane gas at a pressure of 11 inches Water Column Propane.
The controls operate on 12 volts DC (10.5 volts min. - 15.4 volts max.). Operation out of these limits can damage the refrigerator
electrical circuit parts and will void the warranty
Connect the propane gas supply system:
Be very careful when working on or near the propane gas system.
- Do not smoke, or use an open ame near the propane gas system.
- Do not use an open ame to examine for leaks.
- Do not connect the refrigerator to the propane gas tank without a pressure regulator between them.
- To avoid a propane gas leak, always use two wrenches to tighten or loosen the propane gas supply line connections.
- Leaking propane gas can ignite or explode and result in dangerous personal injury or death.
WARNING
!
Installation Manual 18
Connect the gas supply line to the refrigerator:
- Make sure that all tubing and ttings obey all local, state, and national codes about size and type.
- Make sure that all exible metal connectors obey the current CAN1-6.10 Standard.
- Make sure that the materials used for the gas supply line obey both the current ANSI A 119.2 (NFPA 1192) and CSA Z240
Standards on Recreational Vehicles. Norcold recommends the use of 3/8 inch copper tubing as the gas supply line and requires a
3/8 inch SAE (UNF 5/8-18) male are tting as the connection to the refrigerator.
- Put the propane gas supply line up through the oor of the enclosure.
- Make sure the hole through the oor is large enough allow clearance for the gas supply line.
- Put a weather resistant seal (grommet, sealant, etc.) around the gas supply line where it goes through the oor to prevent vibration
and abrasion.
- To prevent vibration and abrasion, make sure that the gas supply line is not against anything in the enclosure.
- Attach the gas supply line to the bulkhead tting of the refrigerator.
Examine the gas supply system for leaks:
Do not allow the leak detecting solution to touch the electrical components. Many liquids are electrically
conductive and can cause electrical shorts and in some cases, re.
Use a leak detecting solution to examine the gas supply line and all propane gas connections for leaks.
If you use compressed air for the test:
- The pressure of the compressed air at the manual shut off valve of the refrigerator must not be more than 1/2 psig (14 inches Water
Column).
- If the pressure of the compressed air is more than 1/2 psig (14 inches Water Column), remove the gas supply line from the
bulkhead tting of the refrigerator before the test.
- If the pressure of the compressed air is equal to or less than 1/2 psig (14 inches Water Column), close the manual shut off valve of
the refrigerator before the test.
WARNING
!
Ignition and Start Up
NOTICE
Before ignition or start up of the refrigerator:
- Make sure the air ow in the lower intake vent, through the refrigerator coils and condenser, and out the upper exhaust vent is not
blocked or decreased.
- Make sure there are no combustible materials in or around the refrigerator.
Refer to the “Display Codes” section of this manual.
Ignition and start up:
If the gas does not ignite in 30 seconds, the gas safety valve of the refrigerator automatically closes and the GAS light
ashes. To reset the controls, push the selector switch to the OFF position.
If the gas does not ignite after several attempts, refer to the “Fault Codes” section of this manual.
Installation Manual 19
Automatic Mode Operation:
1. Push the selector switch [207] to the AUTO position (See
Art01838).
2. Push the temperature switch [142] to the desired temperature
setting.
- If the ON light [60] only comes on, it means that:
- 120 volt AC power is available to the refrigerator.
- The refrigerator is operating on AC electric power.
- If the ON light and the GAS light [62] both come on, it means
that:
- 120 volt AC power is not available to the refrigerator.
- The refrigerator is operating on propane gas.
GAS Mode Operation:
1. Push the selector switch [207] to the GAS position.
2. Push the temperature switch [142] to the desired temperature setting.
- If the ON light and the GAS light [62] both come on, it means that the refrigerator is operating on propane gas.
Do a test of the gas safety valve:
1. Start up the refrigerator in gas mode operation.
2. Open the lower intake vent.
3. Remove one wire from the solenoid of the gas safety valve at the rear of the refrigerator.
4. Within 30 seconds, the ame should extinguish. This means that the gas safety valve is operating correctly.
5. Put the wire back on the solenoid of the gas safety valve.
6. Close the lower intake vent.
Shut down:
To shut down the refrigerator, push the selector switch to the OFF position.
AUTO OFF GAS COLD COLDEST
1 2 3 4 5
ON
GAS check if flashing
207
142
62
60
Art01838
Display Codes
Light and Status
ON light is on.
GAS light is off.
ON light is on.
GAS light is on.
Meaning
The refrigerator is operating on
AC.
The refrigerator is operating on
propane gas.
Installation Manual 20
Fault Codes
Light and Status
ON light is off.
ON light and GAS light both
ash about once per second.
ON light is on.
GAS light ashes about once
per second.
ON light is on, but ashes off 1
time about every 3 seconds.
ON light is on, but ashes off 3
times about every 3 seconds.
GAS light is on.
ON light is on, but ashes off 4
times about every 3 seconds.
Meaning
DC voltage is unavailable to the
refrigerator control panel or the
refrigerator is OFF.
No energy source is available.
AC voltage is not available (or
the refrigerator is in Manual
GAS mode), and the burner did
not ignite or re-ignite.
The burner did not ignite or re-
ignite. The refrigerator is in “gas
lock-out”, but AC voltage has
returned and the refrigerator is
operating on AC.
The temperature sensor failed.
The regerator is operating on
the “Back-Up Operating
System”.
The AC heater failed. The
refrigerator will operate on
propane gas only.
This is a fault within the
refrigerator operating controls.
Corrective Actions
Check:
- That the refrigerator is ON.
- That the battery charging equipment of the vehicle is
operational.
- That the AC/DC converter is operational (if applicable).
- See your dealer or authorized Norcold Service Center.
If in AUTO mode, check:
- That the refrigerator is plugged into a servicable oulet.
- That the fuse or circuit breaker of the vehicle is intact.
- That the vehicle generator is operational (if applicable).
In any mode, check:
- That there is not air in the propane gas supply line. See
“Removing air fromthe propane gas supply lines” section
of this manual.
- That the valve of the propane gas tank(s) is open.
- That the propane gas is at the correct pressure.
- That the manual shut off valve of the refrigerator is open.
- Reset the regerator by turning it OFF and then back to
AUTO or GAS mode.
- See your dealer or authorized Norcold Service Center.
Check:
- That there is not air in the propane gas supply line. See
“Removing air fromthe propane gas supply lines” section
of this manual.
- That the valve of the propane gas tank(s) is open.
- That the propane gas is at the correct pressure.
- That the manual shut off valve of the refrigerator is open.
- Reset the regerator by turning it OFF and then back to
AUTO or GAS mode.
- See your dealer or authorized Norcold Service Center.
This is not owner serviceable. See your dealer or
authorized Norcold Service Center.
This is not owner serviceable. See your dealer or
authorized Norcold Service Center.
This is not owner serviceable. See your dealer or
authorized Norcold Service Center.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Norcold N62/ N82 Guide d'installation

Catégorie
Cheminées
Taper
Guide d'installation
Ce manuel convient également à

dans d''autres langues