Chief KBD-S2S-19T Guide d'installation

Catégorie
Mur
Taper
Guide d'installation

Ce manuel convient également à

I N S T A L L A T I O N I N S T R U C T I O N S
(KBD-MINI-XXX)
(KBD-S2S-XXX)
Under Desk Keyboard Extension Mechanisms
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
KBD-MINI/S2S-XXX
KBD-MINI/S2S-XXX Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all mounting systems
are properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this mounting systems can result in serious personal injury
or damage to equipment! It is the installer’s responsibility to
make sure the structure to which this mounting system is
attached can support five times the combined weight of all
equipment. Reinforce the structure as required before
installing the mounting system.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to mounting system does not
exceed 10 lbs (4.5 kg).
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this mounting system outdoors.
WARNING: RISK OF INJURY TO PERSONS! Do not use
this mounting system / accessory to support video equipment
such as televisions or computer monitors.
--SAVE THESE INSTRUCTIONS--
Installation Instructions KBD-MINI/S2S-XXX
3
DIMENSIONS
KBD-MINI-XXX
KBD-S2S-XXX
KBD-MINI/S2S-XXX Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Installation Instructions KBD-MINI/S2S-XXX
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
1/8" (3.17mm) #2
#3
A (1)
[Keyboard extension mechanism]
B (1)
[Under-desk track]
C (1)
[Bumper] D (20)
#8 x 5/8"
E (1)
[Track guard] F (2)
[Cable clip]
KBD-MINI/S2S-XXX Installation Instructions
6
Assembly And Installation
1. Using under-desk track (B) as a template, mark and drill ten
1/8" diameter pilot holes. (See Figure 1)
Figure 1
2. Use eight #8 x 5/8" wood screws (D) to secure under-desk
track (B) to desk. (See Figure 2)
3. Install bumper (C) with one #8 x 5/8" wood screw (D). (See
Figure 2)
Figure 2
4. Slide keyboard mechanism (A) into under-desk track (B).
(See Figure 3)
Figure 3
5. Install keyboard tray (not included) onto keyboard
mechanism following installation instructions included with
keyboard tray.
6. Use three #8 x 5/8" wood screws (D) to secure track guard
(E) to under-desk track (B) and desk. (See Figure 4)
Figure 4
1
1
x 10
x 10
bumper (C)
installation location
1/8"
f
r
o
n
t
b
a
c
(C)
(D) x 8
2
(B)
(D)
3
(A)
(B)
(KBD-MINI-XXX shown)
4
f
r
o
n
t
b
a
c
k
keyboard tray (example)
(B)
(D) x 3
6
(E)
Installation Instructions KBD-MINI/S2S-XXX
7
Adjustments
Height
1. Lift mechanism arm up or down until desired height is
reached. (See Figure 5)
Tilt
2. Turn tilt knob to adjust keyboard tray tilt. (See Figure 5)
Figure 5
Cable Management
1. Use cable clips (F) under keyboard tray or desk as desired
to manage cables.
1
1
2
2
(KBD-MINI-XXX shown)
KBD-MINI/S2S-XXX Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief, a products division of
Milestone AV Technologies
8800-003072 Rev00
2018 Milestone AV Technologies
www.milestone.com
08/18
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Chief KBD-S2S-19T Guide d'installation

Catégorie
Mur
Taper
Guide d'installation
Ce manuel convient également à

dans d''autres langues