Tetra Contour Gen 2 Back-Bend Guide d'installation

Marque: Tetra

Modèle: Contour Gen 2 Back-Bend

Taper: Guide d'installation

Installation Guide

SIGN297 | DOC-2001571

Contour Gen 2

LED Lighting System

Back Bend

GEXNB32-2, GEXNB65-2, GEXNBRD-2,

GEXNBGL-2, GEXNBBL-2, GEXNBYG-2,

GEXNBRC-2

Save These Instructions

Use only in the manner intended by the manufacturer.

If you have any questions, contact the manufacturer.

For the latest North American install guides for your product go to: https://products.LED.com/led-signage-lighting

For the latest European install guides for your product go to: https://products.LED.com/eu/led-signage-lighting

RETROFIT SIGN CONVERSION LED KIT FOR USE ONLY

IN ACCORDANCE WITH KIT INSTRUCTIONS.

KIT IS COMPLETE ONLY WHEN ALL PARTS REQUIRED

BY THE INSTRUCTIONS ARE PRESENT.

TROUSSE DE CONVERSION À DEL POUR LA

MODERNISATION DES ENSEIGNES

À UTILISER CONFORMÉMENT AU GUIDE D’INSTALLATION.

BG Българската версия на инструкциите за инсталаця и

информация за безопасност могат да бъдат намерени

на следния адрес: https://products.LED.com/eu/led-

signage-lighting

CS Návod k montáží a bezpečnostní informace v češtině

najdete zde: https://products.LED.com/eu/led-signage-

lighting

DA Den danske version af installationsvejledningen og

sikkerhedsoplysninger kan findes på følgende placering:

https://products.LED.com/eu/led-signage-lighting

DE Die deutsche Version der Installationsanleitung und

Sicherheitsinformationen finden Sie in folgendem Verzeic:

https://products.LED.com/eu/led-signage-lighting

EL Μπορείτε να βρείτε την ελληνική εκδχή των οδηγιών

νγκατάστασης και των πληροφοριών ασφάλειας στην

εξής τοποθεσία: https://products.LED.com/eu/led-

signage-lighting

ES La versión española de las instrucciones de instalación y

la información sobre seguridad puede encontrarse en la

siguiente ubicación: https://products.LED.com/eu/led-

signage-lighting

ET Eestikeelse paigaldusjuhendi ja ohutusnñuded leiate

aadressilt: https://products.LED.com/eu/led-signage-

lighting

FI Asennusohjeiden ja turvallisuustietojen suomenkielinen

versio löytyy seuraavasta paikasta: https://products.LED.

com/eu/led-signage-lighting

FR La version française des instructions d’installations et

information de sécurité est disponible à l’adresse suivante:

https://products.LED.com/eu/led-signage-lighting

HR Hrvatska verzija priručnika za ugradnju i sigurnosnih

informacija nalazi se na sljedečoj lokaciji: https://products.

LED.com/eu/led-signage-lighting

HU A telepítési útmutató és a biztnosági információk magyar

nyelvű változata az alábbi címen található: https://

products.LED.com/eu/led-signage-lighting

IT La versione italiana del manuale di installazione e

sicurezza può essere reperita nella seguente sezione:

https://products.LED.com/eu/led-signage-lighting

LT Lietuvišką diegimo instrukcijos ir saugos informacijos

versiją galima rasti šioje vietoje: https://products.LED.

com/eu/led-signage-lighting

LV Uzstādīšanas instrukciju un drošības informāciju latviešu

valodā var atrast šeit: https://products.LED.com/eu/led-

signage-lighting

NL De Nederlandse versie van de installatie-instructies en

veiligheidsinformatie kan op de volgende locatie worden

gevonden: https://products.LED.com/eu/led-signage-

lighting

PL Polską wersję instrukcji instalacji oraz informacje

dotyczące bezpieczeństwa można znaleźć w następującej

lokalizacji: https://products.LED.com/eu/led-signage-

lighting

PT A versão em Português das instruções de instalação e

das informações de segurança pode ser encontrada na

seguinte localização: https://products.LED.com/eu/led-

signage-lighting

RO Versiunea în limba română a instrucţiunilor de instalare

şi a informaţiilor de siguranţă pot fi găsite la: https://

products.LED.com/eu/led-signage-lighting

SV Ni hittar den svenska versionen av

installationsanvisningarna och säkerhetsinformationen på

följande plats: https://products.LED.com/eu/led-signage-

lighting

SL Previdnostna opozorila in varnostne informacije so na

zadnji strani vodnika za namestitev. Pred začetkom

namestitve izdelka jih skrbno preberite: https://products.

LED.com/eu/led-signage-lighting

SK Slovenskú verziu montažnej príručky a bezpečnostnŷch

instrukcií nájdete na nasledujúcej lokalite: https://

products.LED.com/eu/led-signage-lighting

BEFORE YOU BEGIN

Read these instructions completely and carefully.

Prepare Electrical Wiring

Electrical Requirements

• Light engines without light guide limited to indoor dry locations.

• Light engines with light guide acceptable to use in dry, damp or

wet locations when installed correctly.

• The grounding and bonding of the LED Driver shall be done in

accordance with National Electric Code (NEC) Article 600.

• Follow all National Electric Codes (NEC) and local codes.

• These products are only suitable for connection to a circuit from

a Class 2 power source. These products have not been evaluated

for use when connected to a power source that does not comply

with Class 2 voltage and energy limited supplies.

FOR UL ONLY

2424

Volt

Contour Gen 2 (Back Bend) Installation Guide

WARNING / AVERTISSEMENT

RISK OF ELECTRIC SHOCK

• Turn power off before inspection, installation or removal.

• Properly ground power supply enclosure.

RISK OF FIRE

• Use only suitably approved wire for input/output

connections. Minimum size 18 AWG (0.82mm2)

• Follow all local codes.

• Waterproof wire connection for outdoor or wet

installations. See instructions for details.

• Do not stretch light engines.

• Inspect and replace the light engines if any tear or

damage affects their integrity.

• Avoid installation that leads to prolonged exposure to

standing water or ice.

RISQUES DE DÉCHARGES ÉLECTRIQUES

• Coupez l’alimentation avant l’inspection, l’installation ou le déplacement.

• Assurez-vous de correctement mettre à terre l’alimentation

électrique.

RISQUES D’INCENDIE

• N’utilisez que des fils approuvés par UL pour les entrées/sorties de

connexion. Taille minimum 18 AWG (0.82mm2)

• Respectez tous les codes locaux.

• Étanchéifier les connexions électriques effectuées à l’extérieur

ou pour un environnement exposé à l’eau. Voir les instructions

d’installation pour plus de détails.

• Ne pas étirer les modules DEL Contour.

• Inspecter l’intégrité des modules DEL Contour et les remplacer s’ils

sont déchirés ou endommagés.

• Éviter les installations avec une exposition prolongée à l’eau

stagnante ou à la glace.

UL WARNING / AVERTISSEMENT UL

RISK OF FIRE OR ELECTRIC SHOCK

• LED Retrofit Kit installation requires knowledge of

sign electrical systems. If not qualified, do not attempt

installation. Contact a qualified electrician.

• Install this kit only in host signs that have been

identified in the installation instructions and where the

input rating of the retrofit kit does not exceed the input

rating of the sign.

• Installation of this LED retrofit kit may involve drilling or

punching of holes into the structure of the sign. Check

for enclosed wiring andcomponents to avoid damage to

wiring and electrical parts.

• Do not make or alter any open holes in an enclosure of

wiring or electrical components during kit installation.

RISQUE D’INCENDIE OU DE CHOC ÉLECTRIQUE

• L’installation de l’équipement de remplacement DEL exige Ia

connaissance des systèmes électriques pour enseignes. Si non qualifié, ne

tentez pas d’installation. Veuillez contacter un électricien qualifié.

• Risque d’incendie ou de choc électrique. Installez cet ensemble seulement

dans des enseignes hôtes qui ont été identifiés dans les instructions

d’installation et dont la capacité d’entrée de l’ensemble ne dépasse pas la

capacité d’entrée de l’enseigne.

• L’installation de cet équipement de remplacement DEL peut impliquer le

perçage ou le poinçonnage de trous dans la structure du panneau Vérifiez

le câblage et les composants inclus pour éviter d’endommager le câblage

et les composants électriques.

• Ne pas faire ou modifier les trous ouverts dans une enceinte de câblage

ou de composants électriques pendant l’installation de cet équipement

de remplacement DEL.

CAUTION / ATTENTION

RISK OF INJURY

• While performing installations described, gloves, safety

glasses or goggles should be worn.

RISQUE DE BLESSURE

• Lors de l’exécution des installations décrites, des gants, des lunettes de

sécurité ou des lunettes de protection doivent être portées.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

This Class [A] RFLD complies with the Canadian standard ICES-005. Ce DEFR de la classe [A] est conforme à la NMB-005 du Canada.

Contour Gen 2 (Back Bend) Installation Guide

Components and Tools Required

1 2

3 4 5 6 7 8 9 10

Contour Gen 2 Back Bend Light Engine

Tetra® Contour Light Guide

Tetra® Light Engine (GEXNMCAC), Clear Plastic Light Guide (GEXNMC15),

or Stainless Steel Metal Light Guide (93053776) Mounting Clips.

#6, #8 or #10 (M2, M3 or M4) self-drilling pan headed screws

#6 (M2) screws

Minimum 22 AWG (0.33mm2) tie-wire

24 Volt power supply

UL approved 18 AWG (0.82mm2) supply wire

UL approved 22-14 AWG (0.33-2.08mm2) twist-on wire connectors

GEXNSL-2 Field Sleeve

Electrical grade silicone.

Examples of electrical grade silicone:

• Momentive RTV 6702 (white) / RTV 6708 (clear) - Silicone Rubber Adhesive Sealant

• Momentive RTV 162 (White) - Silicone Rubber Adhesive Sealant-Electrical Grade

• Dow Corning 3140 (clear) - Non-Corrosive Flowable

• Dow Corning 3145 (clear or gray) - Non-Corrosive Non-flowable

• Dow Corning RTV 748 (white) - Non-Corrosive Sealant

Tetra® End Caps

Weather box GEXNWB2

Contour Light Guide connector

Contour Light Guide 90° inside corner

Contour Light Guide 90° outside corner

Contour Light Guide 90° planar corner

Optional / Required for Wet Locations

Optional

11 16 17

12 13 14 15

23.8” (0.6m)

8 feet (2.44m)

Cutting Resolution Table

Light Engine Color Cutting Resolution

Red 4 in. (101.6 mm)

Red-Orange, Amber,

Green, Blue, White 3 in. (76.2 mm)

Contour Gen 2 (Back Bend) Installation Guide

18 in. (457mm)

Install a minimum of one clip

per 18 in. (457mm) using #10

(M4) screws.

If cutting the light engine is

required, using the light guide

final length, measure out the

necessary length of Contour

Gen 2 LED light engine to

match.* Use a sharp cutting

tool to cut through light

engine (refer to the Cutting

Resolution Table on page 3).

Installation

Plan the layout by measuring the design layout and dividing by 8 ft . (2.44m) to determine the required quantity of

Contour Gen 2. Refer to the Cutting Resolution Table on page 3 when cutting any Contour Gen 2 section.

Do not use more than one suffix code for each respective application, as mixing suffix codes may result in

appearance variation. Suffix code can be found on the packaging label.

Installation methods shown are for straight runs. For custom shapes, refer to the Light Guide Forming Instructions.

DO NOT bend the light engine to an inside radius that is tighter than 2 in. (50.8 mm).

If you have any questions about these instructions or your specific Contour application, please contact support at

[email protected]

Planning First

METHOD A - Installing Light Engines With Light Guides

1 2

Mounting orientation if moisture

may accumulate inside light guide. NOTE: For side bends, please use Contour Gen 2 Side Bend (GEXNSxx-2) Light Engines

For cut end where the GEXNSL-2

Field Sleeve is being used, fill cap

with electrical grade silicone and

push the Field Sleeve on the end

to seal. Clean excess silicone.

NOTE: Not required if using the

plastic endcap.

Electrical

grade silicone

Cut on marks only

Side bendBack bend

*NOTE: When cut end is going to be installed in a Contour Light Guide Connector (strait or corner), the GEXNSL-2

Field Sleeve should be used. When using the eld sleeve, the light engine must be cut so that it will extend at least

1/2 in. (13 mm) out from the end of the light guide.

Contour Gen 2 (Back Bend) Installation Guide

Insert wire connectors into

weather box. Fill with electrical

grade silicone and close box.

Weather box can be mounted

using #8 (M3) screws.

Apply caps to cut ends: fill cap

with electrical grade silicone

and push cap on the end to

seal. Clean excess silicone.

Weather box

can be painted

–

To connect two light engines,

first strip wire ends back 0.5

in. (13mm). Then join wires

together using twist-on wire

connectors.

Wires between light guide

segments can be folded

behind the light guide and

attached with clear zip ties.

Zip ties should wrap around

outside light guide.

Light guide

Wire loop Light engine (back)

WARNING / AVERTISSEMENT

RISK OF FIRE: Waterproof wire connection and all cut ends for outdoor or wet

installations. Weather box is required for all outdoor or wet locations electrical

connections.

RISQUE D’INCENDIE: Étanchéifier les connexions électriques et sceller

l’extrémité des sections coupées effectuées à l’extérieur ou pour un

environnement exposé à l’eau. Un boitier étanche est requis pour les

connexions électriques effectuées à l’extérieur ou dans un environnement avec

exposition à l’eau.

3/8in. (10mm)

Attach Contour Gen 2 to the

mounting clips, leaving a

3/8 in. (10mm) gap between

sections to allow for expansion

or contraction.

For vertical or near vertical

installations, any cut-end

termination of a Contour

Gen 2 piece shall reside at

the top of the design.

Secure light guide by twisting

tie-wire around the mounting

clip and light guide.

6 7

Cut end

at top

Uncut

wiring at

bottom Fill both end caps with

silicone and install

WARNING/AVERTISSEMENT

RISK OF FIRE: The light engine is not intended for excessive or repetitive

bending or stretching. If the silicone does crack, replace the light engine.

RISQUE D’INCENDIE: Les modules DEL Contour ne sont pas conçus pour des

pliages excessifs, répétitifs ou pour être étirés. Si le silicone montre des signes de

craquement, remplacer le module DEL Contour.

Electrical grade

silicone

Push the light engine segments

down into the light guide.

Contour Gen 2 (Back Bend) Installation Guide

Minimum

2 inch (50.8 mm)

bend radius

Electrical grade

silicone

Linear: At each gap

between sections, apply

silicone on both sides

to secure light guide

connector. Snap on a light

guide connector.

Corner: For all corners (planar,

inside, outside) apply silicone

on both sides to secure light

guide corners. Snap on corner.

For bends, refer to the Light

Guide Forming Instructions

and first bend the light guide.

Once bent, carefully push light

engine into the light guide so

as to not to overly stretch the

light engine.

Joining with Light Guide Connectors, Corners and Bends

WARNING / AVERTISSEMENT

RISK OF FIRE: DO NOT bend the light engine to an inside radius that is tighter than 2 in. (50.8 mm).

RISQUE D’INCENDIE: Ne pas plier les modules DEL Contour avec un rayon de courbure inférieur à 2 pouce (50.8 mm).

12 13 14

Weather box can be painted

Insert wire connectors

into weather box. Fill with

electrical grade silicone and

close box.

Secure the weather box using

a #6 or #8 (M2 or M3) screw.

Power

supply

To Contour

Red (+)

Black or blue (–)

Strip wires back 0.5 in. (13mm).

Connect the gray wire (+)

from the LED strip to the red

wire (+) of the power supply.

Connect the white wire (-)

from the LED strip to the black

or blue wire (-) of the power

supply.Grounding and bonding

must be done in accordance

with National Electrical Code

(Article 600). See power supply

instructions.

Run a wire from the power

supply to a section of Contour

Gen 2. Power supply connection

must be completed in an

acceptable UL/NEMA enclosure.

Power supply loading is

described on page 10.

Connect Power Supply

WARNING/AVERTISSEMENT

RISK OF ELECTRICAL SHOCK: Turn power OFF before inspection, installation or removal.

RISQUES DE CHOC ÉLECTRIQUE: Coupez l’alimentation électrique avant d’inspecter, d’installer ou de déplacer le luminaire.

15 16

To power supply

Red (+)

White wire (–) Gray wire (+)

Black or blue (–)

Electrical

grade

silicone

Do not

bend one

light into a

corner

Contour Gen 2 (Back Bend) Installation Guide

6-12 in. (152-305 mm)

Plan the layout by measuring

the design layout and dividing

by 8 ft . (2.44 m) to determine

the required quantity of Contour

Gen 2. Refer to the Cutting

Resolution Table on page 3 when

cutting any Tetra Contour Gen 2

section.

Do not use more than one

suffix code for each respective

application, as mixing suffix codes

may result in appearance variation.

Suffix code can be found on the

packaging label.

Installation methods shown are for straight runs. For custom shapes, install mounting clips at regular intervals

throughout the shape to provide adequate support for the light engine.

DO NOT bend the light engine to an inside radius that is tighter than 2 in. (50.8 mm). The light engine is not intended

for excessive or repetitive bending or stretching. If the silicone does crack, replace the light engine.

If you have questions about these instructions or your Contour application,

contact support at [email protected]

Planning First

WARNING / AVERTISSEMENT

RISK OF FIRE: Light engine by itself is intended for use in dry indoor application only.

RISQUES DE D’INCENDIE: Les modules DEL Contour utilisés seuls sont conçus pour les environnements intérieurs secs seulement.

METHOD B - Installing Light Engines Without Light Guides (Dry Indoor Only)

Install a mounting clip,

using #6 (M2) counter sink

screws, every 6-12 inches

(152-305 mm) on center until

the end of the run is reached.

Installation

Using the light engine final

length, measure out the

necessary length of Contour

Gen 2 light engine. If required,

using a sharp cutting tool, cut

through light engine.

For cut end, fill cap with

electrical grade silicone and

push GEXNSL-2 Field Sleeve

on the end to seal. Clean

excess silicone.

1 2 3

Electrical

grade silicone

Cut on marks only

NOTE: For side bends, please use Contour Gen 2 Side Bend (GEXNSxx-2) Light

Engines

Side bendBack bend

Contour Gen 2 (Back Bend) Installation Guide

Push into clips +–

Power

supply

To Tetra Contour

Red (+)

Black or blue (-)

To power supply

Red (+)

Run a wire from the

power supply to a section

of Tetra Contour. Power

supply connection must be

completed in an acceptable

UL/NEMA enclosure. Power

supply loading is described on

page 10.

Strip ends back 0.5 in. (13mm).

Connect the gray wire (+) from

the LED strip to the red wire (+)

of the power supply. Connect

the white wire (-) from the LED

strip to the black or blue wire (-)

of the power supply.Grounding

and bonding must be done

in accordance with National

Electrical Code (Article 600). See

power supply instructions.

Black or

blue (-)

Connect Power Supply

WARNING/AVERTISSEMENT

RISK OF ELECTRICAL SHOCK: Turn power OFF before inspection, installation or removal.

RISQUES DE CHOC ÉLECTRIQUE: Coupez l’alimentation électrique avant d’inspecter, d’installer ou de déplacer le luminaire.

7 8

Push each 24 in. (610 mm) light

engine segment into the clips.

Fold loose wires behind light

engines. Do not stretch light

engines.

Strip ends back 0.5 in. (13mm).

Use twist-on wire connectors

to join cut wires together.

Fold wires behind light engines.

5 6

Contour Gen 2 (Back Bend) Installation Guide

1. (Existing Signs Only) Prior to installation, survey the site for information regarding power and accessibility inside

and outside the building. Ensure that the branch circuit supplying the existing transformer or ballast will be within

the voltage ratings of the new LED power supply, and have a current rating not exceeding 20A, or that permitted by

applicable local, state, or country electrical codes (whichever is less).

2. (Existing Signs Only) Remove the existing lighting equipment to be replaced, such as neon tubing or fluorescent

tubes; and associated transformers and ballasts. Care should be taken not to break the existing neon or fluorescent

tubes. NOTE: Follow all federal and local regulations when disposing of neon tubing, fluorescent tubes, transformers

and ballasts.

3. (Existing Signs Only) If removal of the existing lighting equipment eliminates the disconnect switch, as required by

applicable local, state, or country electrical codes; a new disconnect switch must be installed.

4. (Existing Signs Only) Repair and seal any unused openings in the electrical enclosure. Openings greater than 12.7-

mm (1/2-in) diameter require a metal patch secured by screws or rivets and caulked with non-hardening caulk. Smaller

openings may be sealed with non-hardening caulk.

5. Using the layout guidelines above, determine required number of LED modules required to illuminate the sign.

6. A 24VDC Class 2 Power Supply, as listed below, must be used with this retrofit kit. Determine the number of Power

Supplies required to power the number of LED modules required to illuminate the sign, so as not to overload the Power

Supply chosen.

7. Follow Method A, B or C to mount the Contour Gen 2.

8. Connect the DC output of the power supply to the LED modules using the Electrical Connections instructions above.

9. Connect the power unit to the supply in accordance with the applicable local, state, and country electrical codes, and

the instructions found in the power supply installation guide.

10. If required, the disconnect switch shall be installed by qualified personnel, in accordance with applicable local, state,

and country electrical codes.

Retrofit Instructions

Troubleshooting

Symptom Condition Solution

All LEDs are OFF

No AC input. Attach AC input and/or check circuit breaker.

Incorrect wire attachment.

Check wire connection(s) at the Contour Gen 2 LED light

engine and power supply for improper connections or short

circuits. Make sure you have positive to positive and negative

to negative wire connections.

Some LEDs

appear dim

Overload (maximum load exceeded).

Ensure the overall length of Contour Gen 2 LED light engine

does not exceed the maximum load as detailed in the Tetra

Power Supply Installation Instructions.

Maximum recommended supply wire

length exceeded.

Reduce the length of supply wire equal to or below the

recommended maximum.

Mixed Suffix Codes of LED light engine

within an application.

Make sure that all LED light engines have the same Suffix Code

(Suffix Code is located on each packaging label).

Some of the

sections are not

illuminated

Incorrect wire attachment.

Check the wire connections at the Contour Gen 2 LED light

engine for improper connections. Make sure you have positive

to positive and negative to negative wire connections. Check for

improper cutting resolution locations (see table on Page 2).

Light/dark banding

along a section

LED light engine flexed in the wrong

direction or smaller than the minimum

bend radius during installation.

Remove LED light engine and properly install.

Inspect and replace light engine if damaged.

Contour Gen 2 (Back Bend) Installation Guide

This product is intended solely for the use of non-residential signage lighting and is not intended for use in any other applications.

Conforms to the following standards:

NOTE: For linear long runs, center connection to the LED strip is recommended to minimize voltage drop.

*GELP24-60U-GL minimum load = 11 ft. (3.35 m) for GEXNB32-2, GEXNB65-2, GEXNBGL-2, GEXNBBL-2, GEXNBYG-2,

and GEXNBRC-2; or 15 ft. (4.57 m) for GEXNBRD-2.

**GEPS24V50-100W minimum load = 27 ft. (8.23 m) for GEXNB32-2, GEXNB65-2, GEXNBGL-2, GEXNBBL-2, GEXNBYG-2,

and GEXNBRC-2; or 36 ft. (10.97 m) for GEXNBRD-2.

Maximum Loading per 24 VDC Class 2 Power Supply

Power Supply

GEXNB32-2, GEXNB65-2, GEXNBGL-2,

GEXNBBL-2, GEXNBYG-2, GEXNBRC-2 GEXNBRD-2

Rating per module 24VDC, 1.9W/ft. (Strip) 24VDC, 1.4W/ft. (Strip)

GEPS24-25U-NA, GEPS24-25-EU (CE only)

Load shall not exceed 0.83A 11 ft. (3.35 m) 15 ft. (4.57 m)

GEPS24D-60U-GLX, *GELP24-60U-GL

Load shall not exceed 2.5A 28 ft. (8.53 m) 39 ft. (11.88 m)

GEPS24D-80U

Load shall not exceed 3.3A 36 ft. (10.97 m) 49 ft. (14.93 m)

GEPS24-100U-GLX, GEPS24D-100U-NA , GEPS24LT-100U-NA,

USVI-100024FE, USVI-100024FBA

Load shall not exceed 4.0A

44 ft. (13.41 m) 59 ft. (17.98 m)

GEPS24-100U-GLX2, GEPS24-100U-TT, **GEPS24V50-100W

Load shall not exceed 4.0A 46 ft. (14.02 m) 62 ft. (18.89 m)

GEPS24-200U-GLX2

Load shall not exceed 4.0A per each (of 2) output channels

46 ft. (14.02 m) per bank

92 ft. (28.04 m) per PS 62 ft. (18.89 m) per bank

124 ft. (37.78 m) per PS

GEPS24-300U-GLX2

Load shall not exceed 4.0A per each (of 3) output channels

46 ft. (14.02 m) per bank

138 ft. (42.06 m) per PS 62 ft. (18.89 m) per bank

186 ft. (56.67 m) per PS

Dismantling

At the end of life, the contained LED light source may be cut out using suitable wire cutters, removed from the mounting surface,

then replaced per the cutting and installation instructions above, or dismantled and taken to a communal collecting point for

environmentally friendly disposal in accordance with local regulations by a professional installer.

Electrical products must not be thrown out with domestic waste. They must be taken to a communal collecting point for environmentally friendly

disposal in accordance with local regulations. Contact your local authorities or stockist for advice on recycling. The packaging material is recyclable.

Dispose of the packaging in an environmentally friendly manner and make it available for the recyclable material collection-service.

Power Supply

Wattage

18 AWG/0.82 mm2

Supply Wire

16 AWG/1.31 mm2

Supply Wire

14 AWG/2.08 mm2

Supply Wire

12 AWG/3.31 mm2

Supply Wire

25W 20 ft./6.1 m –––