Hitachi C 12LDH Manuel utilisateur

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!

This manual contains important information about product safety. Please read and understand

this manual BEFORE operating the power tool. Please keep this manual available for other

users and owners before they use the power tool. This manual should be stored in safe place.

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la mort

ou de sérieuses blessures corporelles !

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit.

Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce

mode d’emploi à la disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent

l’outil motorisé. Ce mode d’emploi doit être conservé dans un endroit sûr.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar en lesiones

de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y comprenda este

manual ANTES de utilizar la herramienta eléctrica. Guarde este manual para que puedan leerlo otras

personas antes de utilizar la herramienta eléctrica. Este manual debe ser guardado en un lugar seguro.

DOUBLE INSULATION

DOUBLE ISOLATION

AISLAMIENTO DOBLE

(

Laser Marker and Digital Display Equipment

)

(

Outil avec affichage numérique et marqueur à laser

)

(

Equipo marcador láser y visualizador digital

)

(Laser Marker Equipment)

(Outil avec marqueur à laser)

(Equipo marcador láser)

C 12LDH

C 12FDH

Model Compound Miter Saw

Modèle

Scie à onglets combinée

Modelo Ingletadora

CONTENTS

English PAGE PAGE

TABLE DES MATIERES

Français PAGE PAGE

ÍNDICE

Español PÁGINA PÁGINA

INFORMACIÓN IMPORTANTE SOBRE

SEGURIDAD........................................................... 53

SIGNIFICADO DE LAS PALABRAS DE

SEÑALIZACIÓN ..................................................... 53

SEGURIDAD.................................................................... 53

NORMAS DE SEGURIDAD PARA LAS

HERRAMIENTAS ELÉCTRICAS ........................... 53

PIEZAS DE REEMPLAZO.......................................... 57

UTILICE EL CABLE PROLONGADOR

ADECUADO ............................................................ 58

AISLAMIENTO DOBLE PARA OFRECER UNA

OPERACIÓN MÁS SEGURA ................................ 58

OPERACIÓN Y MANTENIMIENTO.............................. 59

NOMENCLATURA DE PARTES ............................... 59

ESPECIFICACIONES ................................................. 60

ACCESORIOS ............................................................. 60

APLICACIONES ......................................................... 61

PREPARATIVOS PREVIOS A LA OPERACIÓN ...... 61

ANTES DE LA UTILIZACIÓN.................................... 62

ANTES DEL CORTE ................................................... 63

APLICACIONES PRÁCTICAS................................... 68

MONTAJE Y DESMONTAJE DE LA

HOJA DE SIERRA .................................................. 75

MANTENIMIENTO E INSPECCIÓN ........................ 76

SERVICIO Y REPARACIONES .................................. 78

IMPORTANT SAFETY INFORMATION ..................... 3

MEANINGS OF SIGNAL WORDS ............................. 3

SAFETY.............................................................................. 3

IMPORTANT SAFETY INSTRUCTIONS FOR

USING ALL POWER TOOLS ................................... 3

REPLACEMENT PARTS.............................................. 6

USE PROPER EXTENSION CORD ............................. 7

DOUBLE INSULATION FOR SAFER OPERATION ... 7

OPERATION AND MAINTENANCE............................... 8

NAME OF PARTS ........................................................ 8

SPECIFICATIONS ........................................................ 9

ACCESSORIES ............................................................. 9

APPLICATIONS ......................................................... 10

PREPARATION BEFORE OPERATION.................... 10

BEFORE USING.......................................................... 11

BEFORE CUTTING ..................................................... 12

PRACTICAL APPLICATIONS ................................... 17

SAW BLADE MOUNTING AND

DISMOUNTING ..................................................... 23

MAINTENANCE AND INSPECTION....................... 24

SERVICE AND REPAIRS........................................... 26

INFORMATIONS IMPORTANTES

DE SÉCURITÉ ......................................................... 27

SIGNIFICATION DES MOTS

D’AVERTISSEMENT ............................................. 27

SECURITE........................................................................ 27

CONSIGNES DE SECURITE RELATIVES AUX

OUTILS ÉLECTRIQUES ......................................... 27

PIECES DE RECHANGE ............................................ 31

UTILISER LE CORDON DE

RALLONGE APPROPRIÉ....................................... 31

DOUBLE ISOLATION POUR UN

FONCTIONNEMENT PLUS SUR.......................... 31

UTILISATION ET ENTRETIEN ...................................... 33

NOM DES PIÈCES ..................................................... 33

SPÉCIFICATIONS ...................................................... 34

ACCESSOIRES ........................................................... 34

APPLICATIONS ......................................................... 35

PRÉPARATION AVANT L’UTILISATION ................ 35

AVANT L’UTILISATION ............................................ 36

AVANT LA COUPE..................................................... 37

APPLICATIONS PRATIQUES................................... 42

INSTALLATION ET RETRAIT DE LA LAME............ 49

ENTRETIEN ET INSPECTION .................................. 50

SERVICE APRÈS-VENTE ET RÉPARATIONS......... 52

3

English

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in the Instruction

Manual before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the failure to observe

basic safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous

situation before it occurs, and by observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections

which contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by WARNINGS on

the power tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been specifically recommended by HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious

injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate

injury, or may cause machine damage.

NOTE emphasizes essential information.

SAFETY

IMPORTANT SAFETY INSTRUCTIONS FOR USING ALL POWER TOOLS

READ ALL OF THE WARNINGS AND OPERATING INSTRUCTIONS IN THIS MANUAL

BEFORE OPERATING OR MAINTAINING THIS TOOL:

WARNING: When using this electric tool, take all necessary precautions to minimize the risk of electric

shock or other personal injury.

In particular, always comply with the following safety rules:

1. ALWAYS KEEP GUARDS IN PLACE and in working order.

2. ALWAYS REMOVE ADJUSTING KEYS AND WRENCHES BEFORE STARTING TOOL.

Always confirm that all keys and adjusting wrenches have been removed from the tool before it is

turned on.

3. ALWAYS KEEP WORK AREA CLEAN. Avoid injuries by not cluttering the work areas and work

benches.

4. NEVER USE TOOL IN HAZARDOUS ENVIRONMENTS. Never use the power tool in damp or

wet places and never expose it to rain. Always keep the work area well lighted.

5. NEVER PERMIT CHILDREN OR OTHERS TO LOITER NEAR THE WORK AREA. Keep all

people (especially children) away from the work area. Always unplug unattended tools and keep the

work place tamper-proof by installing locks on the doors and on the master switches.

6. NEVER FORCE THE TOOL. It will do the job better and more safely if it is operated at the rate for

which it was designed.

7. ALWAYS USE THE RIGHT TOOLS. Never force a tool or an attachment to do a job for which it

was not designed.

8. ALWAYS WEAR PROPER APPAREL WHEN WORKING WITH THE TOOL. Never wear loose

clothing, gloves, neckties, rings, bracelets or other jewelry which may get caught in the moving parts.

Always wear non-slip footwear, preferably with steel toes. Wear protective hair covering to contain

long hair.

4

English

9. ALWAYS USE EYE PROTECTION WHEN WORKING WITH THE TOOL TO PREVENT

EYE INJURY. Ordinary eyeglasses do not provide adequate protection because the lenses are not

made of safety glass. Also, use a face mask for additional safety and wear a dust mask if the cutting

operation produces dust.

10. ALWAYS SECURE THE WORKPIECE TO THE FENCE OR THE TABLE. Use clamps or a vise

to hold the workpiece in place. It is safer than using your hand and it frees both hands to operate the

tool.

11. NEVER OVERREACH. Always keep proper footing and balance when working with the tool.

12. ALWAYS MAINTAIN TOOLS WITH CARE. Always keep tools sharp and clean for the best and

safest performance. Always follow instructions for lubricating the tool and for changing accessories.

13. ALWAYS DISCONNECT THE TOOL before servicing and before changing blades or other

accessories.

14. NEVER RISK UNINTENTIONAL STARTING WHEN PLUGGING IN THE TOOL. Always

confirm that the switch is in the OFF position before inserting the power plug into the receptacle.

15. ALWAYS USE RECOMMENDED ACCESSORIES ONLY WHEN OPERATING THIS TOOL.

Consult this instruction manual for descriptions of recommended accessories. To avoid personal injuries,

use only recommended accessories in conjunction with this tool.

16. NEVER STAND ON THE TOOL. Prevent serious injury by not tipping the tool and by not risking

unintentional contact with the saw blade.

17. ALWAYS CHECK FOR DAMAGED PARTS BEFORE USING THE TOOL. Always check the

guard and all other components for damage before using the tool to assure that they will function

properly. Check all moving parts for proper alignment, freedom from binding and other conditions that

might affect proper operation. Always repair or replace any damaged guards or other damaged

components before using the tool.

18. ALWAYS CONFIRM THE ROTATION DIRECTION OF THE BLADE BEFORE USING THE

TOOL. Always feed work into the tool against the rotation direction of the blade in order to prevent

possible injury.

19. NEVER LEAVE THE TOOL RUNNING WHILE UNATTENDED. TURN POWER OFF. Do not

leave tool until it comes to a complete stop. Always turn the power off when the tool is not in use.

Always unplug the power cord when the tool is not in use.

20. This tool was not designed to be used for mass-production applications and should not be used in

mass-production environments.

21. When servicing this tool, use only authorized replacement parts.

22. Apply 120 volts AC only to this tool. Applying the wrong voltage or applying DC power can cause the

POWER TOOL to operate improperly and cause serious personal injury or damage to the tool.

23. Never raise the saw blade from the workpiece until it has first come to a complete stop.

24. Always use outboard stands to provide support for long workpieces that overhang the table of the

compound miter saw.

25. Always return the carriage to the full rear position after each crosscut operation in order to reduce the

risk of injury.

26. POLARIZED PLUGS To reduce the risk of electric shock, this equipment has a polarized plug (one

blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit

fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the

proper outlet. Do not change the plug in any way.

Specific Safety Rules for Use of this Power Tool

WARNING: The following specific operating instructions must be observed when using this POWER

TOOL in order to avoid injury:

DO’s

ALWAYS OBSERVE THE FOLLOWING RULES TO ASSURE SAFE USE OF THIS TOOL:

1. Review this Manual and familiarize yourself with the safety rules and operating instructions for this

POWER TOOL before attempting to use it.

5

English

2. Always confirm that the POWER TOOL is clean before using it.

3. Always wear snug-fitting clothing, non-skid footwear (preferably with steel toes) and eye protection

when operating the POWER TOOL.

4. Always handle the POWER TOOL carefully. If the POWER TOOL falls or strikes against a hard object, it

might become deformed or cracked or sustain other damage.

5. Always cease operating the saw at once, if you notice any abnormality whatsoever.

6. Always confirm that all components are mounted properly and securely before using the tool.

7. When replacing the saw blade, always confirm that the rpm rating of the new blade is correct for use on

this tool.

8. Always shut off the power and wait for the saw blade to completely stop rotating before doing any

maintenance or adjustments.

9. Always clamp or otherwise secure the workpiece to the fence; otherwise the workpiece might be thrust

form the table and cause bodily harm.

10. During miter or bevel cutting, always wait for the rotation of the blade to stop completely before lifting

the saw blade.

11. Always make a trial run first before attempting any new use of the saw.

12. Always handle the saw blade with care when dismounting and mounting it.

13. Always confirm that the workpiece is free of nails or other foreign objects before beginning a cut.

14. Always keep your hands out of the path of the saw blade.

15. Always confirm that the lower guard is in the proper place before using the saw.

16. Inspect the tool power cords periodically.

17. Always confirm that the proper lengths and types of extension cords are being utilized, if necessary,

before starting the tool.

18. Always confirm that the motor air vents are fully open before using the tool.

19. Always wait until the motor has reached full speed before starting a cut.

20. Always keep the handles dry, clean and free of oil and grease. Hold the tool firmly when in use.

21. Always use outboard stands to provide support for long workpieces that overhang the table of the

compound miter saw.

22. Always operate the tool after ensuring the workpiece is fixed properly with a vise assembly.

23. The operating instructions provided with the tool shall direct the user to secure the tool to supporting

structure if, during normal operation, there is a tendency for the tool to tip over, slide, or walk on the

supporting surface.

DON’Ts

NEVER VIOLATE THE FOLLOWING RULES TO ASSURE SAFE USE OF THIS TOOL:

1. Never operate the POWER TOOL unless you fully understand the operating instructions contained in

this Manual.

2. Never leave the POWER TOOL unattended without first unplugging the power cord.

3. Never operate the POWER TOOL when you are tired, after you have taken any medications, or have

consumed any alcoholic beverages.

4. Never use the POWER TOOL for applications not specified in the instruction manual.

5. Never operate the tool while wearing loose clothing, a necktie or jewelry, or while your hair is uncovered,

to protect against getting caught in the moving machinery.

6. Never reach around the saw blade.

7. Never touch any moving parts, including the blade, while the saw is in use.

8. Never remove any safety devices or blade guards; use of the tool without them would be hazardous.

9. Never lock the lower guard; always confirm that it slides smoothly before using the tool.

10. Never damage the power cord of the tool.

6

English

11. Never attempt to move a plugged-in POWER TOOL while your finger is on the starting switch.

12. Never use the POWER TOOL if the starting switch does not turn on and off properly.

13. Never use the POWER TOOL if the plastic housing or the handle is cracked or deformed.

14. Never use the POWER TOOL near flammable liquids or gases because sparking can cause an explosion.

15. Never clean plastic components with solvents because the plastic may dissolve.

16. Never operate the saw unless all the lower guards are in place.

17. Never raise the saw blade from the workpiece until it has first come to a complete stop.

18. When slide cutting, never pull the handle toward the operator, since this could cause the saw blade to

kick up from the workpiece. Always push the handle away from the operator in a single, smooth motion.

19. Never place your limbs inside of the line next to warning sign “ ” while the tool is being operated.

This may cause hazardous conditions.

20. Never use abrasive type blades on this saw.

21. Never expose to rain or use in damp locations.

22. Never cut ferrous metals or masonry.

WARNING

FOR YOUR OWN SAFETY READ THIS INSTRUCTION MANUAL BEFORE OPERATING THE

COMPOUND MITER SAW

1. Always wear eye protection when using the compound miter saw.

2. Always keep hands out of the path of the saw blade.

3. Never operate the saw without the guards in place.

4. Never perform any freehand operation with the compound miter saw.

5. Never reach around the saw blade.

6. Always turn off tool and wait for saw blade to stop before moving workpiece or changing settings.

7. Always disconnect power before changing blade or servicing.

8. Saw blade diameter is 12” (305 mm).

9. No load speed is 4,000/min.

10. To reduce the risk of injury, return carriage to the full rear position after each crosscut operation.

REPLACEMENT PARTS

When servicing use only identical replacement parts.

Repairs should be conducted only by a Hitachi authorized service center.

7

English

USE PROPER EXTENSION CORD

Make sure your extension cord is in good condition. When using an extension cord, be sure to use one

heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line

voltage resulting in loss of power and overheating. Table shows the correct size to use depending on cord

length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number,

the heavier the cord.

WARNING: Avoid electrical shock hazard. Never use this tool with a damaged or frayed electrical

cord or extension cord.

Inspect all electrical cords regularly. Never use in or near water or in any environment

where electric shock is possible.

DOUBLE INSULATION FOR SAFER OPERATION

To ensure safer operation of this power tool, HITACHI has adopted a double insulation design. “Double

insulation” means that two physically separated insulation systems have been used to insulate the electrically

conductive materials connected to the power supply from the outer frame handled by the operator. Therefore,

either the symbol “ ” or the words and “Double insulation” appear on the power tool or on the nameplate.

Although this system has no external grounding, you must still follow the normal electrical safety precautions

given in this Instruction Manual, including not using the power tool in wet environments.

To keep the double insulation system effective, follow these precautions:

*Only HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble this power tool, and only

genuine HITACHI replacement parts should be installed.

*Clean the exterior of the power tool only with a soft cloth moistened with soapy water and dry thoroughly.

*Never use solvents, gasoline or thinners on plastic components; otherwise the plastic may dissolve.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS

AND

OWNERS OF THIS TOOL!

MINIMUM GAGE FOR CORD SETS

Total Length of Cord in Feet (Meter)

0 – 25 26 – 50 51 – 100 101 – 150

(0 – 7.6) (7.9 – 15.2) (15.5 – 30.5) (30.8 – 45.7)

Ampere Rating AWG

More Not More

Than Than

0 – 6 18 16 16 14

6 – 10 18 16 14 12

10 – 12 16 16 14 12

12 – 16 14 12 Not Recommended

8

English

OPERATION AND MAINTENANCE

NOTE: The information contained in this Instruction Manual is designed to assist you in the safe operation

and maintenance of the power tool. Some illustrations in this Instruction Manual may show details

or attachments that differ from those on your own power tool.

NAME OF PARTS

MODEL C12LDH/MODEL C12FDH

Handle

Head

Gear case

Dust bag

Motor

Saw blade

Lower guard

Rotation direction

Fence (A)

Sub fence (A)

Sub fence (C)

Fence (B)

Table insert

Digital display

(for C12LDH)

Indicator (A)

(for miter scale)

Lever

Side handle

Turntable

Sub fence (B)

Laser marker

Vise assembly

Switch

(for digital display)

(for C12LDH)

Switch

(for laser marker)

Fig. 1

Trigger switch

Nameplate

Locking pin

Set pin

Clamp lever

Holder (B)

Knob (A)

Base

Pully cover

4mm hex. bar wrench

17mm box wrench

Fig. 2-a Fig. 2-b

9

English

SPECIFICATIONS

Item Model C12LDH C12FDH

Motor Type Series commutator motor

Power source Single-phase AC 60Hz

Voltage (Volts) 120

Full-load current (Amp) 15

Digital Display Precision ±0.5° Yes No

Laser Marker Yes Yes

Maximum output <1mW CLASS II Laser Product

Wave length 400~700 nm

Laser medium Laser Diode

Applicable Outside Dia. 12” (305mm)

saw blade Hole Dia. 1” (25.4mm)

No load speed 4000/min

Max. Head Turntable Max. sawing dimension

sawing Miter 0 0 Max. Height 2-3/4” (70mm)

dimension Max. Width 8” (203mm)

or

Max. Height 3-1/2” (89mm)

Max. Width 7-1/2” (190mm)

0Left 45° Max. Height 2-3/4” (70mm)

Right Max. Width 5-1/2” (140mm)

0Left 52° Max. Height 2-3/4” (70mm)

Right Max. Width 4-3/4” (120mm)

Bevel Left 45° 0 Max. Height 1-31/32”(50mm)

Max. Width 8” (203mm)

Right 45° 0 Max. Height 1-1/2” (38mm)

Max. Width 7-1/2” (190mm)

Compound Left 45° Left 45° Max. Height 1-31/32”(50mm)

Right Max. Width 5-1/2” (140mm)

Right 45° Left 45° Max. Height 1-1/2” (38mm)

Right Max. Width 5-1/8” (130mm)

Miter sawing range Left 0° – 52° Right 0° – 52°

Bevel sawing range Left 0° – 48° Right 0° – 48°

Compound sawing range Left and Right (Bevel) 0° – 45°, Left and Right (Miter) 0° – 45°

Net weight 47.4 lbs. (21.5 kg) 46.3 lbs. (21.0 kg)

Cord 2 Conductor type cable 6.7 ft. (2.0m)

ACCESSORIES

WARNING: Accessories for this power tool are mentioned in this Instruction Manual.

The use of any other attachment or accessory can be dangerous and could cause injury or

mechanical damage.

STANDARD ACCESSORIES

Fig. 3

2Dust bag (1 piece)112” (305mm) TCT Saw

blade (1 piece) (For wood)

For how to use, refer to

page 23.

417mm BOX wrench

(1 piece)

3Vise Assembly w/knob bolt

(1 piece)

For how to use, refer to

page 17.

(No. of teeth 32

Code No. 323522)

54mm Hex. bar wrench

For how to use, refer to

page 15.

10

English

OPTIONAL ACCESSORIES...sold separately

1Extension Holder and Stopper (Code No. 323523)

2Crown molding Vise Ass’y (Code No. 323545) (Include Crown molding Stopper (L))

3Crown molding Stopper (L) (Code No. 323546)

4Crown molding Stopper (R) (Code No. 323547)

NOTE: Accessories are subject to change without any obligation on the part of the HITACHI.

APPLICATIONS

Wood and aluminum sash.

PREPARATION BEFORE OPERATION

Make the following preparations before operating the power tool:

1. Installation

11/32” (9mm)

4 Holes

22-3/4” (578mm)

12-19/32”(320mm)

5/16" (8mm) bolt

Base

Work bench 5/16” (8mm) nut

1” (25mm) Thick bench

Fig. 4

Attach the power tool to a level, horizontal work bench in accordance with Fig. 4.

Select 5/16” (8mm) diameter bolts suitable in length for the thickness of the work bench.

Bolt length should be at least 1-3/8" (35mm) plus the thickness of the work bench.

For example, use 2-11/32" (60mm) or larger bolts for a 1" (25mm) thick work bench.

The holder attached to the rear of the base helps stabilize the power tool.

Move

Adjust the holder

until its bottom

surface contacts the

work bench surface.

Holder (B)

6mm bolt

Holder (B) adjustment:

Loosen the 6mm bolt with the supplied 10mm box wrench.

Adjust the holder (B) until its bottom surface contacts the work

bench surface.

After adjustment, firmly tighten the 6mm bolt.

CAUTION: Attach the power tool to a work bench with bolts

(6mm), and if the turntable has been swiveled 45°

degrees or more, be careful not to let the hand

that is holding the side handle get caught between

the side handle and heads of bolts (6mm). Injuries

could result.

Fig. 5

11

English

2. Releasing the locking pin

Handle

Locking pin

Pull

When the power tool is prepared for shipping, its main parts are

secured by a locking pin.

Move the handle slightly so that the locking pin can be disengaged.

NOTE: Lowering the handle slightly will enable you to disengage

the locking pin more easily and safely.

The lock position of the locking pin is for carrying and

storage only.

Fig. 6

3. Installing the dust bag, holder, stopper and vises

(The holder and stopper are optional accessories.)

Attach the dust bag and vise assembly as indicated in Fig. 1 and Fig. 2.

BEFORE USING

1. Make sure the power source is appropriate for the tool.

WARNING: Never connect the power tool unless the available AC power source is of the same

voltage as that specified on the nameplate of the tool.

Never connect this power tool to a DC power source.

2. Make sure the trigger switch is turned OFF.

WARNING: If the power cord is connected to the power source with the trigger switch turned

ON the power tool will start suddenly and can cause a serious accident.

3. Check the saw blade for visible defects.

Confirm that the saw blade is free of cracks or other visible damage.

4. Confirm that the saw blade is attached securely to the power tool.

Using the supplied 17mm box wrench, tighten the bolt on the saw blade spindle to secure the saw

blade.

For details, see Fig. 44-a, Fig. 44-b, Fig. 44-c and Fig. 44-d in the section on “SAW BLADE MOUNTING

AND DISMOUNTING”.

5. Check the lower guard for proper operation.

Lower guard

Lower guard is designed to protect the operator from coming into

contact with the saw blade during operation of the tool.

Always check that the lower guard moves smoothly and covers

the saw blade properly.

Fig. 7

WARNING: NEVER OPERATE THE POWER TOOL if the safety cover does not function smoothly.

6. Confirm the position of the spindle lock before using the tool.

After installing the saw blade, confirm that the spindle lock has been returned to the retract position

before using the power tool (see Fig. 44-b).

12

English

7. Check the Power Receptacle.

To prevent overheating, accidental stopping or intermittent operation, confirm that the power cord

plug fits properly in the electrical receptacle and does not fall out after it is inserted. Repair or replace

the receptacle if it is faulty.

8. Confirm the tool’s power cord is not damaged.

Repair or replace the power cord if an inspection indicates that it is damaged.

AFTER CONNECTING THE POWER PLUG TO AN APPROPRIATE AC POWER SOURCE,

CHECK THE OPERATION OF THE TOOL AS FOLLOWS:

9. Trial Run

After confirming that no one is standing behind, the power tool start and confirm that no operating

abnormalities exist before attempting a cutting operation.

10. Inspect the rotating stability of the saw blade.

For precise cutting, rotate the saw blade and check for deflection to confirm that the blade is not noticeably

unstable; otherwise vibrations might occur and cause an accident.

BEFORE CUTTING

1. Oblique angle

Before the power tool is shipped from the factory, it is adjusted for 0°, right angle, left 45° bevel cutting

angle and right 45° bevel cutting angle with the 8mm bolt (A), 8mm bolt (B) and the 8mm bolt (C).

When changing the adjustment, change the height of the 8mm bolt (A), 8mm bolt (B) or the 8mm bolt

(C) by turning them.

When changing the bevel angle to the right 45°, pull the set pin on the direction shown in Fig. 8-b and

incline the motor head to the right.

When adjusting the motor head to 0°, always return the set pin to its initial position as shown in Fig. 8-

a.

NOTE: Do not adjust the 8mm bolt with bevel plates (Fig. 30) pulled.

8mm bolt (C)

(stopper for right 45° bevel angle)

Indicator

(for right bevel scale)

Return

Set pin

8mm Bolt (B)

(stopper for left 45° bevel angle)

8mm Bolt (A)

(stopper for 0°)

Set pin

Pull

Indicator

(for left

bevel scale)

Fig. 8-a Fig. 8-b

2. Securing the workpiece

WARNING: Always clamp or vise to secure the workpiece to the fence; otherwise the workpiece

might be thrust from the table and cause bodily harm.

3. Installing the holders ... (Optional accessory)

6mm wing bolt

(optional accessory)

Steel square

6mm wing

nut (optional

accessory) Height adjustment

bolt 6mm (optional

accessory)

Holder

(optional

accessory)

Base surface

The holders help keep longer workpieces stable and in place during

the cutting operation.

(1) As indicated in Fig. 9, use a steel square for aligning the upper

edge of the holders with the base surface.

Loosen the 6mm wing nut. Turn a height adjustment bolt 6mm,

and adjust the height of the holder.

(2) After adjustment, firmly tighten the wing nut and fasten the

holder with the 6mm wing bolt (optional accessory). If the length

of Height Adjustment Bolt 6mm is insufficient, spread a thin

plate beneath. Make sure the end of Height Adjustment Bolt

6mm does not protrude from the holder.

Fig. 9

13

English

4. Stopper for precision cutting ... (Stopper and holder are optional accessory)

Stopper

(optional accessory)

Holder

(optional accessory)

6mm wing nut (optional accessory)

Height adjustment bolt 6mm (optional accessory)

6mm wing bolt

(optional accessory)

Workpiece

The stopper facilitates continuous precision cutting in lengths of

11" to 17-3/4" (280mm to 450mm).

To install the stopper, attach it to the holder with the 6mm wing

bolt as shown in Fig. 10.

Fig. 10

5. Confirmation for use of sub fence (A)

WARNING: In the case of right bevel cutting, turn the sub fence (A) clockwise. Unless it is turned

clockwise, the main body or saw blade may contact the sub fence (A), resulting in an

injury.

Sub Fence (A)

Turn

Left bevel angle cutting

Direct angle cutting Right bevel

angle cutting

Fence (A)

This power tool is equipped with a sub fence (A).

In the case of direct angle cutting and left bevel angle cutting, use

the sub fence (A). Then, you can realize stable cutting of the material

with a wide back face.

In the case of right bevel cutting, raise the sub fence (A) up as

illustrated in Fig. 11 and then turn it clockwise.

Fig. 11

6. Confirmation for use of sub fence (B)

WARNING: In the case of left bevel cutting, turn the sub fence (B) counterclockwise. Unless it is

turned counterclockwise, the main body or saw blade may contact the sub fence (B),

resulting in an injury.

Turn

Left bevel angle

cutting Right bevel angle cutting

Direct angle cutting

Sub fence (B) Fence (B)

This power tool is equipped with a sub fence (B). In the case of

direct angle cutting and right bevel angle cutting, use the sub fence

(B). Then, you can realize stable cutting of the material with a wide

back face. In the case of left bevel cutting, raise the sub fence (B)

up as illustrated in Fig.12 and turn it counterclockwise.

Fig. 12

7. Confirmation for use of sub fence (C)

WARNING: In the case of left bevel angle cutting, remove the sub fence (C). If the sub fence (C) is not

removed, the sub fence (C) will contact the main unit or saw blade and result in injury.

Sub fence (C)

Fence (B)

This power tool is equipped with a sub fence (C).

In the case of direct angle cutting and right bevel angle cutting, use

the sub fence (C).

Then, you can realize stable cutting of the material with a wide

back face.

Fig. 13

14

English

Sub fence (C)

Fence (B)

Knob (B)

In the case of left bevel angle cutting, remove the sub fence (C) by

sliding to the side and removing from the top as shown in Fig. 13.

Loosen knob (B) then remove the sub fence (C) (Fig. 14)

WARNING: To attach the sub fence (C), insert then securely

tighten knob (B).

If knob (B) is loose, the sub fence (C) may move

during cutting and result in injury.

Fig. 14

8. Position adjustment of laser line

WARNING: *Make sure before plugging the power plug into the receptacle that the main body

and the laser marker are turned off.

*Exercise utmost caution in handling a switch trigger for the position adjustment of

the laser line, as the power plug is plugged into the receptacle during operation.

If the switch trigger is pulled inadvertently, the saw blade can rotate and result in

unexpected accidents.

*Do not remove the laser marker to be used for other purposes.

CAUTION:

Fig. 15

Fig. 16

*Laser radiation- Do not stare into beam.

*Laser radiation on work table. Do not stare into beam.

If your eye is exposed directly to the laser beam, it can be hurt.

*Do not dismantle it.

*Do not give strong impact to the laser marker (main body of tool); otherwise, the

position of a laser line can go out of order, resulting in the damage of the laser

marker as well as a shortened service life.

*Keep the laser marker lit only during a cutting operation. Prolonged lighting of the

laser marker can result in a shortened service life.

*Use of controls or adjustments or performance of procedures other than those

specified herein may result in hazardous radiation exposure.

NOTE: *Perform cutting by overlapping the ink line with the laser line.

*When the ink line and the laser line are overlapped, the strength and weakness of light will

change, resulting in a stable cutting operation because you can easily discern the conformity

of lines. This ensures the minimum cutting errors.

*In outdoor or near-the-window operations, it may become difficult to observe the laser line

due to the sunlight. Under such circumstances, move to a place that is not directly under the

sunlight and engage in the operation.

*Do not tug on the cord behind the motor head or hook your finger, wood and the like around

it; otherwise, the cord may come off and the laser marker may not be lit up.

*The laser marker will not light up if the digital display switch is turned off. (only on C12LDH)

15

English

Ink lining can be easily made on this tool to the laser marker. A

switch lights up the laser marker. (Fig. 17)

Turning on the laser marker switch while the digital display swich

is on, light up the laser marker. (On the C12FDH, only the laser

marker switch.)

Depending upon your cutting choice, the laser line can be aligned

with the left side of the cutting width (saw blade) or the ink line on

the right side.

The laser line is adjusted to the width of the saw blade at the time

of factory shipment. Adjust the positions of the saw blade and the

laser line taking the following steps to suit the use of your choice.

Laser marker switch

Digital display switch

Fig. 17

(1) Light up the laser marker and make a groove of about 3/16"

(5mm) deep on the workpiece that is about 1-1/2" (38mm) in

height and 3-1/2"(89mm) in width. Hold the grooved workpiece

by vise as it is and do not move it. (Fig. 18)

Workpiece Saw blade

Marking

(pre-marked)

Cutting width

Fig. 18 (2) Then insert a 4mm hex. bar wrench in the 12 diameter hole on

the side of the gear case, turn the hex. socket set screw to move

the laser line. (If you turn the Hex. socket screw clockwise, the

laser line will shift to the right and if you turn it counterclockwise,

the laser line will shift to the left.) When you work with the ink

line aligned with the left side of the saw blade, align the laser

line with the left end of the groove. (Fig. 19) When you align it

with the right side of the saw blade, align the laser line with the

right side of the groove.

Move

4mm hex. bar wrench

12 diameter

hole

Turn

Groove

Move

Laser line

Gear case

Fig. 19 (3) After adjusting the position of the laser line, draw a right-angle

ink line on the workpiece and align the ink line with the laser

line. When aligning the ink line, slide the workpiece little by

little and secure it by vise at a position where the laser line

overlaps with the ink line. Work on the grooving again and check

the position of the laser line. If you wish to change the laser

line's position, make adjustments again following the steps from

(1) to (3).

Laser line

Marking (pre-marked)

Fig. 20

NOTE: Check and make sure on a periodic basis if the position of the laser line is in order. As regards

the checking method, draw a right-angle ink line on the workpiece with the height of about

1-1/2" (38mm) and the width of 3-1/2" (89mm), and check that the laser line is in line with the

ink line [The deviation between the ink line and the laser line should be less than the ink line

width (0.5mm)]. (Fig. 20)

16

English

9. DIGITAL DISPLAY PANEL (for C12LDH)

Miter angle window

(Displays arrows show angle and

direction that turntable is rotating.

Left is ←, Right is →.)

Bevel angle window

(Displays arrows showing motor head

bevel angle and bevel direction. Left is ←,

Right is →.)

Miter angle reset button Bevel angle reset button

Back light ON/OFF switch (Press and the switch illuminates.

Press again and the lighting turns off.)

Fig. 21

Laser marker switch

Digital display switch

(for C12LDH)

(Also serves as laser

marker power switch.)

(1) Turning on the digital display switch shows 0° for both miter

and bevel angle, regardless of main unit angle.

(2) Align the main unit angle with the tilt angle (0°) and miter angle

(0°) and hold down their reset buttons for at least 0.2 second.

(3) Turning on the laser marker switch while the digital display

switch is on, lights up the laser marker. (On the C12FDH, only

the laser marker switch.)

Fig. 22-a

CAUTION: When operating the digital panel, have the motor head section at the top limit position

and the blade stopped.

Note: • Before starting to cut, align the main unit to the miter angle 0° and the bevel angle 0° and

hold down thier reset buttons for at least 0.2 second. If you press the digital display switch to

ON without aligning the main unit to 0°, then the figures appearing on the digital display and

the main unit angle will not match.

• The laser marker will not light up if the digital display switch is turned off. (only on C12LDH)

• Do not use the main unit near equipment that generates electrical noise such as generators.

Electrical noise might cause faulty readings or operation on the digital display.

CAUTION: When operating the digital panel, have the motor head section at the top limit position

and the blade stopped.

Reset button

Side handle

CAUTION: If the figure shown on the miter angle digital

display is different from the positive stop angle

(for example, 45.0° → 45.5°, 31.6° → 32.0°) then

the positive stop has probably deviated slightly

from its correct position. If this happens, do as

follows.

(1) Move the turntable left and right with the side

handle loosened, and set the turntable to the

correct position.

(2) If the figures on the display and positive stop

still do not match, then return the turntable

to the 0° position. Next move the turntable

left and right with the side handle loosened

as shown in Fig. 22-b. After setting it to the

correct position 0°, press the reset button

again.

Move the turntable left and right

with the side handle loosened and

set it to the correct position.

Fig. 22-b

17

English

PRACTICAL APPLICATIONS

WARNING: *To avoid personal injury, never remove or place a workpiece on the table while the tool

is being operated.

*Never place your limbs inside of the line next to warning sign while the tool is being

operated. This may cause hazardous conditions (see Fig. 23).

Warning sign Line

Warning sign

Line

Fig. 23

1. Switch operation

Hole

Trigger switch

Pull the trigger to turn on the switch, release it to shut it off.

After releasing the trigger, make sure the trigger has gone all the

way back and the switch is turned off.

Fig. 24

WARNING: This will ensure that the power tool cannot be turned on accidentally or by someone

(especially a child) who is not qualified to use the power tool.

To prevent unauthorized operation of this tool, insert a padlock through the hole in

the switch trigger.

2. Using the Vise Assembly (Standard accessory)

Screw holder Knob

Vise plate

Workpiece

6mm wing bolt (A)

Vise shaft

Fence

6mm wing

bolt (B)

(1) The vise assembly can be mounted on either the left fence

{Fence (B)} or the right fence {Fence (A)} by loosening the 6mm

wing bolt (A).

(2) The screw holder can be raised or lowered according to the

height of the workpiece by loosening the 6mm wing bolt (B).

After the adjustment, firmly tighten the 6mm wing bolt (B) and

fix the screw holder.

(3) Turn the upper knob and securely fix the workpiece in position

(Fig. 25).

Fig. 25

WARNING: Always firmly clamp or vise to secure the workpiece to the fence; otherwise the

workpiece might be thrust from the table and cause bodily harm.

CAUTION: Always confirm that the motor head (see Fig. 1) does not contact the vise assembly

when it is lowered for cutting. If there is any danger that it may do so, loosen the 6

mm wing bolt (B) and move the vise assembly to a position where it will not contact

the saw blade.

18

English

3. Cutting Operation

Adjusting line

(Front view)

Marking

(pre-marked)

Marking

(pre-marked)

Fig. 26

(1) As shown in Fig. 26 the width of the saw blade is the

width of the cut. Therefore, slide the workpiece to the

right (viewed from the operator’s position) when length

b is desired, or to the left when length a is desired.

If a laser marker is used, align the laser line with the left

side of the saw blade, and then align the ink line with

the laser line.

(2) Once the saw blade reaches maximum speed, push the

handle down carefully until the saw blade approaches

the workpiece.

(3) Once the saw blade contacts the workpiece, push the

handle down gradually to cut into the workpiece.

(4) After cutting the workpiece to the desired depth, turn

the power tool OFF and let the saw blade stop completely

before raising the handle from the workpiece to return

it to the full retract position.

WARNING: *Confirm that the trigger switch is turned OFF and the power plug has been removed

from the receptacle whenever the tool is not in use.

*When you cut the workpiece, avoid any cutoff thinner than the clearance between

the cutting edge and the saw blade. Otherwise, the cut-off material can enter the

clearance between the cutting edge and the saw blade and scatter around you,

resulting in an injury.

CAUTION: *Increased pressure on the handle will not increase the cutting speed.

On the contrary, too much pressure may result in overload of the motor and/or

decreased cutting efficiency.

*If the handle is pressed down with excessive or lateral force, the saw blade may

vibrate during the cutting operation and cause unwanted cutting marks on the

workpiece, thus reducing the quality of the cut. Accordingly, press the handle down

gently and carefully.

4. Miter cutting procedures

Miter scale

Turn the turntable

Loosen side handle

Tighten

Push

Lever

Indicator

(for miter scale)

Turntable

Fig. 27

(1) Loosen the side handle and push the lever for angle stoppers.

Then, adjust the turntable until the indicator aligns with desired

setting on the miter scale (Fig. 27).

(2) Re-tighten the side handle to secure the turntable in the desired

position.

NOTE: *Positive stops are provided at the right and left of the 0°

center setting, at 15°, 22.5°, 31.6° and 45° settings.

Check that the miter scale and the tip of the indicator

are properly aligned.

Use the positive stop position as the yardstick

operations.

*Operation of the saw with the miter scale and indicator

out of alignment, or with the side handle not properly

tightened, will result in poor cutting precision.

CAUTION: Never remove the side handle; use of the tool without it would be hazardous.

To prevent an accident or personal injury always firmly tighten the miter handle.

19

English

5. Bevel cutting procedures

Indicator

(for bevel

scale) Indicator

(for right bevel scale)

Clamp lever

Tighten

Set pin

Pull

Loosen

(1) Loosen the clamp lever and bevel the saw blade to the left or to

the right.

When tilting the motor head to the right pull the set pin towards

the rear.

(2) Adjust the bevel angle to the desired setting while watching

the bevel angle scale and indicator, then secure the clamp lever.

Fig. 28

WARNING: When the workpiece is secured on the left or right side of the blade, the short cut-off

portion will come to rest on the right or left side of the saw blade. Always turn the

power off and let the saw blade stop completely before raising the handle from the

workpiece.

If the handle is raised while the saw blade is still rotating, the cut-off piece may

become jammed against the saw blade causing fragments to scatter about

dangerously.

When stopping the bevel cutting operation halfway, start cutting after pulling back

the motor head to the initial position.

Starting from halfway, without pulling back, causes the lower guard to be caught in

the cutting groove of the workpiece and to contact the saw blade.

6. Bevel angle fine adjustment

Handle

Knob (A)

Clamp

lever

Fig. 29

8 mm bolt (B)

Clamp lever

Knob (A)

Hinge

8 mm bolt (A)

Bevel plate

Right bevel angle

Left bevel angle

Pull

Fig. 30

(1) Grip the handle on the motor head and position it at the bevel angle you need. Temporarily tighten

the clamp lever.

CAUTION: If not tightened firmly enough the motor head might suddenly move or slip, causing

injuries. Be sure to tighten the motor head section enough so it will not move.

(2) Make fine adjustments to the bevel angle by gripping the handle and moving the knob (A).

NOTE: Turning knob (A) clockwise, allows fine adjustment of the main unit to the left (as seen from

front).

Turning knob (A) counterclockwise, allows fine adjustment of the main unit to the right (as

seen from front).

If you wish to cut left bevel angle 48° or right bevel angle 48°, pull the bevel plate backwards

until the hinge contacts either the 8mm bolt (A) or the 8mm bolt (B) then cut diagonally left or

right. Setting to cut left bevel angle 48° or right bevel angle 48° can be done easily.

(3) After adjusting to the desired angle, tighten the clamp lever and clamp the motor head.

CAUTION: Always check that the clamp lever is secured and the motor head is clamped. If you

attempt angle cutting without clamping the motor head, then the motor head might

shift unexpectedly causing injuries.

7. Compound cutting procedures

Compound cutting can be performed by following the instructions in 4 and 5 above. For maximum

dimensions for compound cutting, refer to “SPECIFICATIONS” table on page 9.

CAUTION: Always secure the workpiece with the right hand side for compound cutting. Never

rotate the table to the right for compound cutting, because the saw blade might then

contact the clamp or vise that secures the workpiece, and cause personal injury or

damage.

20

English

8. Crown molding cutting procedures

Fig. 31 shows two common crown molding types having angles of (θ) 38° and 45°.

For the typical crown molding fittings, see Fig. 32.

B lower surface

A

upper surface

Ceiling

Walt

Ceiling

Wall

Inside corner Outside corner

Fig. 31 Fig. 32

The table below shows the miter angle and the bevel angle settings that are ideal for the two crown

molding types.

NOTE: For convenience, positive stops are provided for the miter setting (left and right 31.6°) positions.

For miter cut setting

If the turntable has been set to either of the angles described, move the turntable adjusting side handle

a little to the right and left to stabilize the position and to properly align the miter angle scale and the tip

of the indicator before the operation starts.

For bevel cut setting

Move handle on bevel section to the left and check that the position is stable and that the bevel angle

scale and the tip of the indicator are properly aligned. Then tighten the clamp lever.

(1) Setting to cut crown moldings at positions 1 and 4 in Fig. 32 (see Fig. 33; tilt the head to the left):

1Turn the turntable to the right and set the Miter Angle as follows:

*For 45° type crown moldings: 35.3° ( mark)

*For 38° type crown moldings: 31.6° ( mark)

2Tilt the motor head to the left and set the Bevel Angle as follows:

*For 45° type crown moldings: 30° ( mark)

*For 38° type crown moldings: 33.9° ( mark)

3Position the crown molding so that the upper surface (A in Fig. 31) contacts the fence as indicated

in Fig. 35.

(2) Setting to cut crown moldings at positions 2 and 3 in Fig. 32 (see Fig. 34; tilt the head to the left):

1Turn the turntable to the left and set the Miter Angle as follows:

*For 45° type crown moldings: 35.3° ( mark)

*For 38° type crown moldings: 31.6° ( mark)

2Tilt the head to the left and set the Bevel Angle as follows:

*For 45° type crown moldings: 30° ( mark)

*For 38° type crown moldings: 33.9° ( mark)

3Position the crown molding so that the lower surface (B in Fig. 31) contacts the fence as in Fig. 36.

To process crown molding at

positions 1 and 4 in Fig. 32. To process crown molding at

positions 2 and 3 in Fig. 32.

Type of

Crown

Molding

45° Type

38° Type

Miter Angle

Setting

right 35.3°

( mark)

right 31.6°

( mark)

Miter Angle

Setting

left 35.3°

( mark)

left 31.6°

( mark)

Bevel Angle

Setting

left 30°

( mark)

left 33.9°

( mark)

Bevel Angle

Setting

left 30°

( mark)

left 33.9°

( mark)

La page charge ...

Hitachi C 12LDH Manuel utilisateur

Hitachi C 12LDH Manuel utilisateur

dans d''autres langues

Documents connexes