Modern Forms PD-W74615 Lucid Mode d'emploi

Taper
Mode d'emploi
1Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
746 - Outdoor Pendant
PD-W74615
HARDWARE
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, nen laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
A1 C1 D1B1
Wire Connector
Qty: 3 pcs
Mounting Screw
Qty: 1 Extra
Screw
Qty: 2 Extra
Junction Box Screw
Qty: 2 pcs + 1 Extra
2Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
746 - Outdoor Pendant
PD-W74615
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture,
including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area.
Be careful not to lose any small parts necessary for installation.
MOUNTING THE FIXTURE Fig. 1
3. Remove the mounting screw (C1) from the xture.
4. Choose number of rods suitable for your application.
5. Thread the xture wire through the rods and canopy.
6. Connect the canopy, rods and xture body. Make sure all are tightened.
7. Secure mounting plate to the junction box using junction box screws
(B1).The side of the mounting platemarked “GND” must face out.
CONNECTING THE WIRES Fig. 2
8. Cut the extra wire. Connect the xture wires with junction box wires as
shown in Fig. 2, making sure that all wire connectors (A1) are secured.
If your outlet box has a green or bare copper ground wire, connect the
xture’s ground wire to it. Otherwise, connect the xtures ground wire
directly to the mounting plate using the green screw provided. After
wires are connected, tuck them carefully inside the junction box.
COMPLETING THE INSTALLATION (Fig. 2, 3, 4)
9. Place the glass to the bottom ring, put the top ring to the glass and
secure it by using two screws (D1).
10. Place the xture over the mounting plate and secure with
mounting screws (C1)
11. For slope ceiling application, rotate wire at the top of the stem to ensure
luminaries is aiming (Fig. 3).
12. To prevent the moisture from entering the outlet box and causing
a short, use clear caulking (i.e. indoor/outdoor silicone sealant)
to outline the outside of xture back plate (Fig. 4)
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring
Fig. 3
Turn to down
FIG.1
A1
C1
B1
D1
Wire Connector
Mounting Screw
Junction Box Screw
Screw
Canopy
1 x 6” Rod
3 x 12” Rods
Fixture
Glass
Bottom Ring
Top Ring
Junction Box
Mounting Plate
Back Plate Dimensions
GND
4 5/8”
1 3/4”
1 1/8”
1 3/8”
Ø4 3/4”
120°
Junction Box
Caulking
Fig. 4 Sealing
  • Page 1 1
  • Page 2 2

Modern Forms PD-W74615 Lucid Mode d'emploi

Taper
Mode d'emploi