• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
•
• Retain installation instructions for future maintenance reference.
All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by . Substitution of parts or accessories not designated for use with this product by dweLED
could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any
parts are damaged or missing.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits dweLED. Remplacer des pièces ou accessoires non conçus pour ce
produit dweLED pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez
contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
Wire Connector
Qty: 3pcs+1 Extra
Mounting Screw
Qty: 1 Extra
AB
INSTALLATION INSTRUCTION
WS-240926-CS
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. 1
Dec 2023
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
South East Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91761
Central Manufacturing Facility
1700 South J Elmer Freeway
Suite 100
Cedar Hill, TX 75104
mounting back plate.
4. Secure the mounting back plate to the junction box using standard junction box screws that comes with the junction box.
(i)using any other non-original-manufacturer provided junction box screw may result in safety issue.
(ii) The side of the mounting plate marked “GND” must face out.
5. The lamp can switch between three color temperatures (2700K-3000K-3500K),which can be adjusted to your preference with
the switch in the canopy (Fig. 3).
to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
mounting back plate using the mounting screw (B). (Fig.1)
A
Mounting Back Plate
Fixture
Junction Box
Mounting Screw
B
Wire Connector
Junction Box Screw
Canopy
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
3000K 2700K3500K
2"
4 3/8"
7/8"
INSTALLATION INSTRUCTION
WS-240926-CS
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. 2
Dec 2023
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
South East Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91761
Central Manufacturing Facility
1700 South J Elmer Freeway
Suite 100
Cedar Hill, TX 75104
-
1
-
2
dans d''autres langues
Documents connexes
-
WAC Lighting WS-W241310 Mode d'emploi
-
-
-
-
-
-
-
-