Signature Kitchen Suite UPFXC2466S Le manuel du propriétaire

ENGLISH FRANÇAIS ESPAÑOL

OWNER’S MANUAL

FRENCH DOOR REFRIGERATOR

Please read this owner's manual thoroughly before operating

and keep it handy for reference at all times.

UPFXC2466*

www.signaturekitchensuite.com (USA)

www.signaturekitchensuite.ca (CANADA)

MFL68507671_Rev.10

2TABLE OF CONTENTS

TABLE OF CONTENTS

3 PRODUCT FEATURES

4

IMPORTANT SAFETY INSTRUCTIONS

7 PRODUCT OVERVIEW

7 Refrigerator Exterior

8 Refrigerator Interior

9 INSTALLATION

9 Installation Overview

9 Product Specifications

10 Unpacking the Refrigerator

10 Choosing the Proper Location

11 Measuring Clearances

11 Removing/Assembling the Refrigerator Door

Handles

12 Removing/Assembling the Freezer Drawer

Handle

12 Removing/Assembling the Doors and

Drawers

13 Removing the Left Refrigerator Door

14 Removing the Right Refrigerator Door

15 Assembling the Right Refrigerator Door

16 Assembling the Left Refrigerator Door

17 Removing the Freezer Drawers

19 Assembling the Freezer Drawers

20 Connecting the Water Line

20 Before You Begin

20 Water Pressure

20 What You Will Need

21 Water Line Installation Instructions

23 Turning On the Power

24 Leveling and Door Alignment

24 Leveling

24 Door Alignment

25 OPERATION

25 Before Use

26 Control Panel

26 Control Panel Features

29 In-Door Ice Bin

29 Detaching the In-Door Ice Bin

29 Assembling the In-Door Ice Bin

30 Automatic Icemaker

30 Turning the Automatic Icemaker On or Off

31 When to Turn the Icemaker Off

31 Normal Sounds You May Hear

31 Preparing for Vacation

32 Operating the Dispenser

33 Ice and Water Dispenser

33 Dispenser

33 Using the Dispenser

33 Locking the Dispenser

33 Cleaning the Dispenser Stand

34 Storing Food

34 Food Preservation Location

35 Food Storage Tips

35 Storing Frozen Food

36 Humidity Controlled Crisper and

Glide’N’Serve

37 Detaching and Assembling the Storage Bins

38 Door-in-Door

40 Adjusting the Refrigerator Shelves

41 SMART FUNTIONS

41 SIGNATURE KITCHEN SUITE Application

43 Smart Grid Function

45 Smart Diagnosis™ Feature

46 MAINTENANCE

46 Cleaning

47 Replacing the Fresh Air Filter

47 Replacing the Water Filter

52 TROUBLESHOOTING

62 LIMITED WARRANTY

3

PRODUCT FEATURES

ENGLISH

PRODUCT FEATURES

* Depending on the model, some of the following functions may not be available.

FILTERED WATER AND ICE DISPENSER

The water dispenser dispenses fresh, chilled water.

The ice dispenser dispenses cubed and crushed ice.

DOOR ALARM

The Door Alarm function is designed to prevent the refrigerator from

malfunctioning if a refrigerator door or freezer drawer remains open. If a

refrigerator door or freezer drawer is left open for more than 60 seconds, a

warning alarm sounds at 30-second intervals.

HUMIDITY CONTROLLED CRISPER

The Humidity Controlled Crisper is designed to help keep fruits and

vegetables fresh and crisp. Control the amount of humidity in the crisper by

adjusting the setting between Low and High.

GLIDE‘N’SERVE

Glide‘N’Serve provides storage space with a variable temperature control

that keeps the compartment colder than the refrigerator. It is a convenient

place to store sandwiches or meat to be cooked.

AUTO CLOSING HINGE

The refrigerator doors and freezer drawers close automatically with a slight

push. (The door only closes automatically when it is open at an angle less

than 30°.)

ICE PLUS

Ice production can be increased by approximately 20 percent when the

freezer section is maintained at the coldest temperature for a 24-hour

period.

4IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

This guide contains many important safety messages. Always read and obey all safety messages.

WARNING

To reduce the risk of fire, electric shock, or personal injury when using your product, basic safety

precautions should be followed, including the following:

Power

•NEVER unplug the refrigerator by pulling on the

power cord. Always grip the plug firmly and pull

it straight out from the outlet.

•If the supply cord is damaged, it must be

replaced by the manufacturer or its service

agent or a similarly qualified person in order to

avoid a hazard. Do not use a cord that shows

cracks or abrasion damage along its length or at

either the plug or connector end.

•Do not use an uncertified power outlet.

•Unplug the power plug immediately in the

event of a blackout or thunderstorm.

•Plug in the power plug with the power cord

facing downward.

Installation

•Contact an authorized service center before you

install or relocate the refrigerator.

•When moving your refrigerator away from the

wall, be careful not to roll over or damage the

power cord.

•Prior to use, ensure that you are connecting

this product to a dedicated, grounded electrical

outlet rated for use with this product (115V,

60Hz, AC only). It is the user’s responsibility to

replace a standard 2-prong wall outlet with a

standard 3-prong wall outlet.

•Do not install the refrigerator where there may

be a danger of the unit falling.

Use

•DO NOT allow children to climb, stand, or hang

on the refrigerator doors or on the shelves

in the refrigerator. They could damage the

refrigerator and seriously injure themselves.

•Do not hang on to or place heavy objects on the

refrigerator’s dispenser.

•Do not place heavy or dangerous objects (bottles

with liquid) on the refrigerator.

•Do not put live animals inside the refrigerator.

•Do not allow children to climb into the product

when it is in use.

•In the event of a gas leak (propane/LPG), ensure

adequate ventilation and contact an authorized

service center before resuming use. Do not

touch or disassemble the electric outlet of the

refrigerator.

•In the event of a refrigerant leak, move

flammable objects away from the refrigerator.

Ensure adequate ventilation and contact an

authorized service center.

•Do not use or place flammable substances

(chemicals, medicine, cosmetics, etc) near the

refrigerator or store them inside the refrigerator.

Do not place the refrigerator in the vicinity of

flammable gas.

•Do not overfill or pack items too tightly into

door bins. Doing so may cause damage to the

bin or personal injury if items are removed with

excessive force.

WARNING You can be killed or seriously injured if you do not follow instructions.

CAUTION

Indicates an imminently hazardous situation which, if not avoided, may result

in minor or moderate injury, or product damage.

This is the safety alert symbol. It alerts you to safety messages that inform you of

hazards that can kill or hurt you or others, or cause damage to the product.

All safety messages will be preceded by the safety alert symbol and the hazard

signal word WARNING or CAUTION. These words mean:

5

IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

•This product is not to be used for special

purposes such as the storage of medicine or

test materials or for use on ships, etc.

•Unplug the power plug before cleaning or

repairing the refrigerator.

•When you replace the light bulb in the

refrigerator, unplug the refrigerator or turn off

the power.

•Do not modify or extend the power cord.

•Do not use a dryer to dry the interior. Do not

light a candle to remove interior odors.

•For your safety, this appliance must be properly

grounded. Have the wall outlet and the circuit

checked by a qualified electrician to make sure

the outlet is properly grounded.

•Do not use an outlet that can be turned off

with a switch. Do not use an extension cord. It

is the user’s responsibility to replace a standard

2-prong wall outlet with a standard 3-prong wall

outlet.

•Do not, under any circumstances, cut or

remove the third (ground) prong from the

power cord.

•Do not use an adapter plug and plug the power

plug into a multi-outlet extension cord.

•Disconnect the power cord immediately if you

hear a noise, smell a strange odor or detect

smoke coming from the appliance.

•Turn the power off if water or dust penetrates

into the refrigerator. Call a service agent.

•Do not disassemble or modify the refrigerator.

•Do not put hands, feet, or metal objects below

or behind the refrigerator.

•Do not operate the refrigerator or touch the

power cord with wet hands.

•In refrigerators with automatic icemakers, avoid

contact with the moving parts of the ejector

mechanism or with the heating element that

releases the cubes. Do not place fingers or

hands on the automatic ice-making mechanism

while the refrigerator is plugged in.

•When dispensing ice from the dispenser, do

not use crystal ceramics.

•Do not touch the cold surfaces in the freezer

compartment with wet or damp hands, when

your refrigerator is in operation.

•Do not put glass containers, glass bottles or

soda in the freezer.

•This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they

have been given supervision or instruction

concerning the use of the appliance by a

person responsible for their safety.

•Do not refreeze frozen food that has thawed

completely. Doing so may result in a serious

health issue.

•If you are throwing away your old refrigerator,

make sure the CFC coolant is removed for

proper disposal by a qualified servicer. If you

release CFC coolant, you may be fined or

imprisoned in accordance with the relevant

environmental law.

•Junked or abandoned refrigerators are

dangerous, even if they are sitting for only a

few days. When disposing of the refrigerator,

remove the packing materials from the door

or take off the doors but leave the shelves

in place so that children may not easily climb

inside.

•When discarding the appliance, remove the

door gasket while leaving the shelves and

baskets in place, and keep children away from

the appliance.

•If connected to a circuit protected by fuses,

use time delay fuse.

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

To reduce the risk of fire, electric shock, or personal injury when using your product, basic safety

precautions should be followed, including the following:

6IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

CAUTION

Installation

•The refrigerator must be properly installed

in accordance with the Installer Instructions

that were taped to the front of the

refrigerator.

•Be careful when you unpack and install the

refrigerator. Immediately dispose of plastic

and other packing materials out of reach of

children.

•The appliance must be positioned for easy

access to a power source.

Use

•Close the door carefully when children are

around.

•Keep fingers out of pinch point areas;

clearances between the doors and cabinets

are necessarily small. Be careful closing

doors when children are nearby.

•If you store food improperly, be aware that it

may fall and cause injury.

•Do not use aerosols near the refrigerator.

•Do not store articles on the top of the

appliance.

Maintenance

•Do not use strong detergents like wax or

thinners for cleaning. Clean with a soft cloth.

•Wipe foreign objects (such as dust and

water) off the prongs of the power plug and

contact areas regularly.

•Do not store, disassemble or repair the

refrigerator by yourself.

•Remove any dust or foreign matter from the

power plug pins.

•Do not use a wet or damp cloth when

cleaning the plug.

•If the refrigerator is disconnected from the

power supply, you should wait for at least

five minutes before plugging it back in.

•If you notice a chemical or burning plastic

smell or see smoke, unplug the refrigerator

immediately and contact your Signature

Kitchen Suite Service Center.

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

To reduce the risk of fire, electric shock, or personal injury when using your product, basic safety

precautions should be followed, including the following:

7

PRODUCT OVERVIEW

ENGLISH

PRODUCT OVERVIEW

Use this page to become more familiar with the parts and features of your refrigerator.

*The appearance and specifications of the actual product may differ depending on the model.

Refrigerator Exterior

Filtered Water and

Ice Dispenser

Dispenses purified water and ice.

LED Display

Displays the refrigerator and

freezer temperature, the water

filter condition and the dispenser

status.

Control Panel

Sets the refrigerator and freezer

temperatures, the water filter

condition and the dispenser mode.

Refrigerator

Freezer

Ez Handle

Easily opens the freezer

door.

LED Light

LED lights up when the

freezer door is opened.

Button

Opens the Door-in-Door

compartment

Handle

Opens and closes

the door.

8PRODUCT OVERVIEW

Refrigerator Interior

Water filter

Purifies water.

NOTE

Replace the water filter every 6 months, or

as needed. See Replacing the Filter in this

manual for details.

* (Water filter is only

available on some

models.)

Indoor Ice Bin

Ice cubes are

automatically produced.

Crisper

Controls humidity and

helps vegetables and

fruit to stay crisp.

Auto Closing Hinge

The refrigerator doors

and freezer drawers close

automatically when pushed

slightly.

(The door only closes

automatically when it is open

at an angle of less than 30°.)

Fixed Door Bin

Used to preserve

chilled food or drinks.

Durabase® and Durabase® Divider

The Durabase is a storage space

recommended for the preservation of

large food items. The Durabase Divider is

used to organize the Durabase area into

sections. It can be adjusted from side to

side to accommodate items of different

sizes.

Glide‘N’Serve

Store food items at a

different temperature than

the regular refrigerator

area.

Pullout Drawers

Used for extra storage

within the freezer

compartment.

LED interior lamps

The interior lamps light up the

inside of the refrigerator.

Door-in-Door Case

A convenient storage area for

frequently-used items that require

easy access.

Adjustable Refrigerator Shelf

The shelves in the refrigerator are

adjustable to meet individual storage

needs.

Cheese & Butter Bin

Cheese & Butter and

Condiment bins, that

are specially designed

for these items, making

spreading butter and

slicing cheese easier.

Condiment Bin

9

INSTALLATION

ENGLISH

INSTALLATION

Installation Overview

Read the following installation instructions first after purchasing this product or transporting it to

another location.

1 Unpacking your

refrigerator

2 Choosing the proper

location

3 Disassembling/Assembling

4 Connecting the water

supply and water line

5 Leveling and Door

Alignment

NOTE

Connect to potable water supply

only.

Product Specifications

The appearance and specifications listed in this manual may vary due to constant product

improvements.

Models UPFXC2466*

Description French door refrigerator

Electrical requirements 115 VAC @ 60 Hz

Min. / Max. Water pressure

20 – 120 psi (138 – 827 kPa)

Dimensions

35 3/4” (W) X 30 7/8” (D) X 70 1/4” (H), 42 3/4” (D w/ door open)

908 mm (W) X 785 mm (D) X 1785 mm (H), 1085 mm (D w/ door open)

Net weight 324 lb. (147 kg)

10 INSTALLATION

Unpacking the Refrigerator

Choosing the Proper Location

WARNING

•Use two or more people to move and

install the refrigerator. Failure to do so

can result in back or other injury.

•Your refrigerator is heavy. When moving

the refrigerator for cleaning or service,

be sure to protect the floor. Always pull

the refrigerator straight out when moving

it. Do not wiggle or walk the refrigerator

when trying to move it, as floor damage

could occur.

•Keep flammable materials and vapors,

such as gasoline, away from the

refrigerator. Failure to do so can result in

fire, explosion, or death.

•Remove tape and any temporary labels from

your refrigerator before using.

Do not remove any warning labels, the model

and serial number label, or the Tech Sheet that

is located under the front of the refrigerator.

•To remove any remaining tape or glue, rub

the area briskly with your thumb.

Tape or glue residue can also be easily removed

by rubbing a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with

warm water and dry.

•Do not use sharp instruments, rubbing

alcohol, flammable fluids, or abrasive

cleaners to remove tape or glue.

These products can damage the surface of your

refrigerator.

•Reinstall or adjust shelves as needed.

Refrigerator shelves are installed in the shipping

position. Reinstall shelves according to your

individual storage needs.

Water Water supply must be easily connected for the automatic icemaker.

Water pressure 20–120 psi on models without water filter. 40–120 psi on models with

water filter.

Electricity Use an individual, grounded outlet:115 Volts, 60 Hz, AC, 15 Amps

minimum.

WARNING: Do not overload house wiring and cause a fire hazard

by plugging in multiple appliances in the same outlet with the

refrigerator. To reduce the risk of electric shock, do not install the

refrigerator in a wet or damp area.

Floor Floor must be level and solidly constructed. Adjust the leveling legs to

compensate for any unevenness in the floor. Do not install on carpeting,

soft tile, a platform, or a weakly supported structure.

Ambient

temperature

Temperature must be between 55°F (13°C) and 110°F (43°C). If the

ambient temperature is too low or high, performance may be affected.

Clearances Allow at least 24 in. (61 cm) in front to open the doors. Allow at least

2 in. (5.08 cm) between the back of the refrigerator and the wall. If the

refrigerator is too close to adjacent items, freezing capability may decrease

and electricity consumption may increase.

11

INSTALLATION

ENGLISH

Removing the Handles

1 Loosen the set screws with a 3/32 in.

Allen wrench and remove the handle.

2 Loosen the mounting fasteners that

connect to the refrigerator

door and handle using

a 1/4 in. Allen wrench, and

remove the mounting

fasteners.

Measuring Clearances

•Check the dimensions of the product and the

installation path to ensure there is sufficient

room to move the refrigerator through doors

or narrow openings.

•If an opening is too narrow to fit the

refrigerator through, remove the refrigerator

doors. See Removing/Assembling the Doors

and Drawers in this manual.

•The installation location chosen for the

refrigerator should allow space behind the

unit for connections and airflow and space in

front to open the doors and drawers.

2” (5.08 cm)

24” (61 cm)

Removing/Assembling the

Refrigerator Door Handles

Tools Needed

3/32 in. Allen wrench

¼ in. Allen wrench

Assembling the Handles

1 Assemble the mounting fasteners at

both ends of the handle using a 1/4 in.

Allen wrench.

2 Place the handle on the door by fitting

the handle footprints over the mounting

fasteners and

tightening

the set

screws

with a 3/32 in.

Allen wrench.

NOTE

When it is necessary to move the

refrigerator through a narrow opening,

removing the doors is the recommended

procedure. If it is necessary to remove

the handles, follow the directions below.

12 INSTALLATION

Tools Needed

Flat-head screwdriver

10 mm or 13/32 in. socket wrench

Phillips screwdriver

Removing/Assembling the

Freezer Drawer Handle

Removing the Handles

1 Loosen the set screws located on the

lower side of the handle with a 1/8 in. Allen

wrench and remove the handle.

2 Loosen the mounting fasteners that

connect to the

freezer drawer

and handle

using a 1/4 in.

Allen wrench,

and remove

the mounting

fasteners.

Assembling the Handles

1 Assemble the mounting fasteners at

both ends of the handle using a 1/4 in. Allen

wrench.

2 Place the handle on the door by fitting

the handle

footprints over

the mounting

fasteners and

tightening the

set screws

with a 1/8 in.

Allen wrench.

WARNING

•If your entrance door is too narrow for the

refrigerator to pass through, remove the

refrigerator doors and move the refrigerator

sideways through the doorway.

•Use two or more people to remove and

install the refrigerator doors. Failure to do

so can result in back or other injury.

•Disconnect the electrical supply to the

refrigerator before installing. Failure to do

so could result in serious injury or death.

•Do not put hands, feet or other objects into

the air vents or bottom of the refrigerator.

You may be injured or receive an electrical

shock.

•Be careful when handling the hinge and

stopper, to avoid injury.

•Remove food and bins before detaching the

doors and drawers.

Removing/Assembling the

Doors and Drawers

When it is necessary to move the refrigerator

through a narrow opening, removing the doors

is the recommended procedure.

WARNING

When assembling or disassembling the

handle:

•Grasp the handle tightly to avoid dropping it.

•Do not swing the handle into nearby people

or animals.

•Make sure that the bracket hole of the

handle fits properly into the stopper bolt of

the door. Assemble the set screws to fix

the handle into place.

•Make sure that there is not a gap between

the door and handle after assembling the

handle.

13

INSTALLATION

ENGLISH

2 Remove the screw from the hinge cover

at the top of the refrigerator. Lift the hook

(not visible), located at the bottom of the

front side of the cover with a flat-head

screwdriver.

3 Remove the cover and pull out the tube .

Disconnect all wire harnesses .

4 Rotate the hinge lever counterclockwise

. Lift the top hinge free of the hinge

lever latch.

CAUTION

When lifting the hinge free of the latch, be

careful that the door does not fall forward.

Hinge Lever Latch

5 Lift the door from the middle hinge pin and

remove the door.

CAUTION

Place the door, inside facing up, on a

non-scratching surface.

Removing the Left Refrigerator Door

1 The water supply is connected to the

upper right part of the rear surface of the

refrigerator. Remove the ring in the joint

area. Hold the water supply connection

and gently push the Collet to detach the

water supply line as shown in and .

NOTE

Detachment of the water supply line is

applicable only when detaching the left

refrigerator door.

Collet

14 INSTALLATION

Removing the Right Refrigerator

Door

1 Remove the top hinge cover screw .

Lift the hook (not visible), located at the

bottom of the front side of the cover ,

with a flat-head screwdriver.

2 Detach the wire harness .

CAUTION

When lifting the hinge free of the hinge

lever latch, be careful that the door

does not fall forward.

Hinge Lever Latch

3 Rotate the hinge lever clockwise.

Lift the top hinge free of the hinge

lever latch.

4 Lift the door from the middle hinge pin and

remove the door.

CAUTION

Place the door on the floor, inside

facing up, on a non-scratching surface.

15

INSTALLATION

ENGLISH

Install the right-side door first.

1 Make sure that the plastic sleeve is

inserted in the bottom of the door. Lower

the door onto the middle hinge pin as

shown in the figure.

2 Fit the hinge over the hinge lever latch

and slot it into place. Rotate the lever

counterclockwise to secure the hinge.

Assembling the Right Refrigerator Door

Hinge Lever Latch

4 Make sure that the door-switch located

inside the cover is tightly connected.

Position the cover in its place. Insert and

tighten the cover screw .

3 Connect the wire harness .

16 INSTALLATION

Assembling the Left Refrigerator

Door

Install the left refrigerator door after the right

door is installed.

1 Make sure that the plastic sleeve is

inserted in the bottom of the door. Install

the refrigerator door onto the middle hinge.

2 Fit the hinge over the hinge lever latch

and slot it into place. Rotate the lever

clockwise and fasten the hinge.

3 Connect all the wire harnesses.

Hinge Lever Latch

4 Push the water supply tube into the hole

on the top case and pull it through the

backplate.

5 Hold the water supply connection and

gently push in the collet to connect the

water supply line as shown in and .

Insert the tube at least 5/8 inch (15 mm) into

the connector. Assemble the clip to the

joint part for fastening.

6 Make sure that the door-switch located

inside the cover is tightly connected. Place

the cover in its position and tighten the

cover screw .

Collet

17

INSTALLATION

ENGLISH

CAUTION

•Use two or more people to remove and

install the freezer drawer. Failure to do so

can result in back injury or other injury.

•Do not hold the handle when removing

or replacing the drawer. The handle may

come off, resulting in personal injury.

•Be careful of sharp hinges on both sides

of the drawer.

•When you lay the drawer down, be

careful not to damage the floor.

•Do not sit or stand on the freezer drawer.

•To prevent accidents, keep children

and pets away from the drawer. Do not

leave the drawer open. If the Durabase®

storage bin is removed from the freezer

drawer, there is sufficient space for a

small child or pet to crawl inside.

NOTE

1) Gently press the collet and insert the

tube until only one line shows on the

tube.

(Correct)

(Incorrect)

2) Pull the tube to make sure that the

tube is tightly fastened and then insert

the clip.

Removing the Freezer Drawers

In the following figures, the Pullout Drawers

located above the freezer drawer are not

shown for clarity.

Collet

Tube

Insert Line

Clip

(Durabase®)

18 INSTALLATION

2 Pull the upper pullout drawer open to full

extension.

3 Gently lift and pull out the ice bin.

On the left rail, use a flat blade screwdriver

to push in on the tab to release the drawer

from the rail, as shown below. Once the

left side is loose, push the tab on the right

side with your finger to release the drawer.

Lift the front of the drawer up, then pull it

straight out.

4

Remove the Durabase basket from the rail

assembly. Remove the screws from the rails

at both ends of the freezer drawer.

5

Grip both sides of the drawer and pull it up to

remove it from the rails.

6

Hold both rails and push them in

simultaneously.

CAUTION

Do not hold the handle when removing

or replacing the drawer. The handle may

come off, causing personal injury.

1 Open the freezer drawer. Open the lower

pullout drawer, lift the front of the drawer,

and then pull the drawer out.

19

INSTALLATION

ENGLISH

4 Insert the upper pullout drawer into the

frame, and push the drawer back into place

until you hear a click.

5 Place the ice bin back in the upper pullout

drawer.

6 Insert the lower pullout drawer in the rail

assembly.

Assembling the Freezer Drawers

1

Pull out both rails simultaneously, until both

rails are fully extended.

2

Grasp the freezer drawer on each side and

hook the drawer supports into the rail tabs

located on both sides.

CAUTION

Do not hold the handle when removing

or replacing the drawer. The handle

may come off, causing personal injury.

3 Lower the door into its final position and

tighten the screws located on both sides.

Insert the Durabase basket in the rail

assembly.

20 INSTALLATION

CAUTION

Wear eye protection during installation

to prevent injury.

Connecting the Water Line

Before You Begin

This water line installation is not covered by the

refrigerator warranty. Follow these instructions

carefully to minimize the risk of expensive water

damage.

Water hammer (water banging in the pipes) in

house plumbing can cause damage to refrigerator

parts and can lead to water leakage or flooding.

Call a qualified plumber to correct water hammer

before installing the water supply line to the

refrigerator.

If you use your refrigerator before connecting

the water line, make sure the icemaker power

button is turned off.

Water Pressure

The water pressure must be between 20 and

120 psi. If the refrigerator is installed in an area

with low water pressure (below 20 psi), you can

install a booster pump to compensate for the low

pressure.

If a reverse osmosis water filtration system is

connected to your cold water supply, this water

line installation is not covered by the refrigerator

warranty. Follow the instructions carefully to

minimize the risk of expensive water damage.

If a reverse osmosis water filtration system is

connected to your cold water supply, the water

pressure to the reverse osmosis system needs

to be a minimum of 40 to 60 psi (276-414 kPa or

2.8-4.2 kgf/cm², less than 2-3 sec. to fill a cup of

7 oz or 198 cc capacity).

If the water pressure from the reverse osmosis

system is less than 20 psi or 138 kPa or 1.4 kgf/

cm² (takes more than 4 sec to fill a cup of 7 oz or

198 cc capacity):

•Check to see if the sediment filter in

the reverse osmosis system is blocked.

Replace the filter if necessary.

•Allow the storage tank on the reverse

osmosis system to refill after heavy

usage.

•If the issue concerning water pressure

from reverse osmosis remains, call a

licensed, qualified plumber.

•All installations must be in accordance

with local plumbing code requirements.

What You Will Need

•Copper Tubing, ¼ in. outer diameter, to

connect the refrigerator to the water

supply. Be sure both ends of the tubing

are cut square.

•To determine how

much tubing you need:

measure the distance

from the water valve on the back of

the refrigerator to the water supply

pipe. Then, add 8 feet (2.4 m). Be sure

there is sufficient extra tubing (about 8

feet [2.4 m] coiled into 3 turns of about

10 in. [25 cm] diameter) to allow the

refrigerator to move out from the wall

after installation.

•Power drill.

•½ in. or adjustable

wrench.

•Flat blade and Phillips

head screwdrivers.

•Two ¼ in. outer

diameter compression

nuts and 2 ferrules (sleeves) to connect the

copper tubing to the shutoff valve and

the refrigerator water valve.

CAUTION

Do not install the icemaker tubing in

areas where temperatures fall below

freezing.

CAUTION

To prevent burns and product damage,

only connect the refrigerator water line to

a cold water supply.

La page charge ...

Signature Kitchen Suite UPFXC2466S Le manuel du propriétaire

Signature Kitchen Suite UPFXC2466S Le manuel du propriétaire

dans d''autres langues

Autres documents