Mammoth P7TQ Guide d'installation

P7TQ- 072 / 090 / 120 Series

Single Package Heating / Electric Cooling Rooftop Units

INSTALLATION INSTRUCTIONS

IMPORTANT

ATTENTION INSTALLERS:

It is your responsibility to know this product better than your customer. This includes being

able to install the product according to strict safety guidelines and instructing the customer on

how to operate and maintain the equipment for the life of the product. Safety should always be

the deciding factor when installing this product and using common sense plays an important

role as well. Pay attention to all safety warnings and any other special notes highlighted in the

manual. Improper installation of the furnace or failure to follow safety warnings could result in

serious injury, death, or property damage.

These instructions are primarily intended to assist qualiﬁed individuals experienced in the proper

installation of this appliance. Some local codes require licensed installation/service personnel

for this type of equipment. Please read all instructions carefully before starting the installation.

Return these instructions to the customer’s package for future reference.

DO NOT DESTROY. PLEASE READ CAREFULLY & KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

2

TABLE OF CONTENTS

IMPORTANT SAFETY INFORMATION .....................3

REQUIREMENTS & CODES .....................................4

GENERAL INFORMATION ........................................4

About the Rooftop Unit ..................................................... 4

Before You Install this Equipment .................................... 4

Locating the Unit .............................................................. 4

Heating Load .................................................................... 5

CIRCULATING AIR SUPPLY .....................................5

Unconditioned Spaces ..................................................... 5

Acoustical Ductwork ......................................................... 5

Air Filter Requirements .................................................... 5

UNIT INSTALLATION ................................................6

Packaging Removal ......................................................... 6

Rigging & Hoisting ........................................................... 6

Minimum Clearance Requirements .................................. 6

Vertical to Horizontal Conversion ..................................... 6

Rooftop Mounting ............................................................. 7

Ground Level ................................................................... 7

Condensate Drain ............................................................ 7

ELECTRICAL WIRING ............................................... 8

Pre-Electrical Checklist .................................................... 8

Line Voltage ..................................................................... 8

Grounding ........................................................................ 8

Unbalanced 3-Phase Supply Voltage .............................. 8

Thermostat / Low Voltage Connections ........................... 9

Heat Anticipator ............................................................... 9

Blower Speed ................................................................... 9

STARTUP & ADJUSTMENTS ...................................10

Pre-Start Check List ........................................................ 10

Startup Procedures .......................................................... 10

Air Circulation ................................................................... 10

System Cooling ................................................................ 10

System Heating - Field Installed Electric Heat ................. 10

Verifying Temperature Rise ............................................. 10

Verifying Operation of Over-Temperature Limit Control

(Field Installed Electric Heat) ........................................... 10

OPERATING SEQUENCE .........................................11

Cooling Mode ................................................................... 11

Heating Mode (Optional Electric Heat) ............................ 11

Blower Mode .................................................................... 11

Unit Fails to Operate ........................................................ 11

TROUBLESHOOTING ...............................................11

REFRIGERANT CHARGING .....................................11

Table 2. Heat Rise and Range ..................................... 11

Charging Charts & Application Notes .............................. 12

Table 3. Refrigerant Charge Table ............................... 12

Figure 9. P7TQ-072 Charging Chart (6-Ton) ............... 12

Figure 10. P7TQ-090 Charging Chart (7.5-Ton) .......... 13

Figure 11. P7TQ-120 Charging Chart (10-Ton) ........... 13

UNIT MAINTENANCE ................................................14

Routine Maintenance ....................................................... 14

Air Filters ...................................................................... 14

Blower Compartment .................................................... 14

Condensate Drain & Outdoor Coil ................................ 14

Electrical ....................................................................... 14

Motor / Bearing Lubrication .......................................... 14

FIGURES & TABLES .................................................16

Figure 13. Physical Dimensions for P7TQ Units .......... 16

Table 4. Center of Gravity & Unit Shipping Weights .... 17

Blower Performance Data ................................................ 18

Table 5. P7TQ-072 C/D/N Series -

Downﬂow Models ........................................... 19

Table 6. P7TQ-072 C/D/N Series -

Horizontal Models .......................................... 20

Table 7. P7TQ-090 C/D/N* Series -

Downﬂow Models ........................................... 21

Table 8. P7TQ-090 C/D/N* Series -

Horizontal Models .......................................... 22

Table 9. P7TQ-120 C/D/N* Series -

Downﬂow Models ........................................... 23

Table 10. P7TQ-120 C/D/N*Series -

Horizontal Models ........................................ 24

Table 11. P7TQ-090C/D/N* Series High Static Drive ... 25

Table 12. P7TQ-120C/D/N* Series High Static Drive ... 25

Electrical Data & Diagrams .............................................. 26

Figure 14. Wiring Diagram for 6 Ton Models

(208/230 V, 2 Speed, 2 HP Motor) .............. 26

Figure 15. Wiring diagram for 6 Ton Models

(460 V, 2 Speed, 2 HP Motor) ..................... 28

Figure 16. Wiring diagram for 6 Ton Models

(575 V, 2 Speed, 2 HP Motor) ..................... 30

Figure 17. Wiring diagram for 6 Ton Models

(208/230 V, 5 Speed, 3 HP ECM Motor) ..... 32

Figure 18. Wiring diagram for 6 Ton Models

(460 V, 5 Speed, 3 HP ECM Motor) ............ 34

Figure 19. Wiring diagram for 6 Ton Models

(575 V, 5 Speed, 3 HP ECM Motor) ............ 36

Figure 20. Wiring diagram for 7.5 & 10 Ton Models

(208/230 V, 2 Speed, 2 HP Motor) .............. 38

Figure 21. Wiring diagram for 7.5 & 10 Ton Models

(460 V, 2 Speed, 2 HP Motor) ..................... 40

Figure 22. Wiring diagram for 7.5 & 10 Ton Models

(575 V, 2 Speed, 2 HP Motor) ..................... 42

Figure 23. Wiring diagram for 7.5 & 10 Ton Models

(208/230 V, 5 Speed, 3 HP ECM Motor) ..... 44

Figure 24. Wiring diagram for 7.5 & 10 Ton Models

(460V, 5 Speed, 3 HP ECM Motor) ............. 46

Figure 25. Wiring diagram for 7.5 & 10 Ton Models

(575 V, 5 Speed, 3 HP ECM Motor) ............ 48

Table 13. MCA / MOP Data (Single Circuit) ................. 50

Table 14. MCA / MOP Data (Multiple Circuit) ............... 51

INSTALLATION CHECKLIST ............................................. 54

3

IMPORTANT SAFETY INFORMATION

Please read all instructions before servicing this equipment.

Pay attention to all safety warnings and any other special

notes highlighted in the manual. Safety markings are used

frequently throughout this manual to designate a degree or

level of seriousness and should not be ignored.

WARNING indicates a potentially hazardous situation that if

not avoided, could result in personal injury or death.

CAUTION indicates a potentially hazardous situation that

if not avoided, may result in minor or moderate injury or

property damage.

WARNING:

Improper installation, service, adjustment, or

maintenance may cause explosion, ﬁre, electrical

shock or other hazardous conditions which may

result in personal injury or property damage.

Unless otherwise noted in these instructions,

only factory authorized kits or accessories may

be used with this product.

WARNING:

Do not place combustible material on or against

the unit cabinet. Do not place combustible

materials, including gasoline and any other

ﬂammable vapors and liquids, in the vicinity of

the unit.

WARNING:

PROPOSITION 65 WARNING: This product

contains ﬁberglass insulation. Disturbing the

insulation of this product during installation,

maintenance, or repair may expose you to

ﬁberglass insulation.

• Breathingthismaterialmaycauserespiratory

irritations.

• Fiberglass insulation may also cause eye

irritation, skin sensitization, or other allergic

responses in susceptible individuals.

• Always wear goggles, disposable gloves,

long sleeved shirt, and appropriate breathing

protection when working near this insulation.

If contact with skin occurs, wash immediately

with soap and water. In case of contact with

eyes, ﬂush immediately with water for at least

15 minutes. Contact a physician if needed.

WARNING:

Rooftop installations with vertical ducts must be

provided with a 90 degree elbow installed in the

supply duct to comply with U.L. (Underwriters

Laboratories) codes for use with electric heat

so the elements are not directly over a supply

grille.

WARNING:

The information listed below and must be followed

during the installation, service, and operation

of this unit. Unqualiﬁed individuals should

not attempt to interpret these instructions or

install this equipment. Failure to follow safety

recommendations could result in possible

damage to the equipment, serious personal

injury or death.

• Thisequipmentcontainsliquidandgaseousrefrigerant

under high pressure. Installation or servicing should only

be performed by qualiﬁed trained personnel thoroughly

familiar with this type equipment.

• Beforebeginningtheinstallation,verifythattheunitmodel

is correct for the job. The unit model number is printed on

the data label.

• Followallprecautionsintheliterature,ontags,andon

labels provided with the equipment. Read and thoroughly

understand the instructions provided with the equipment

prior to performing the installation and operational checkout

of the equipment.

• This unit is designed only for outdoor installations and

should be located with consideration of minimizing the

length of the supply and return ducts.

• Theinstallershouldbecomefamiliarwiththeunit’swiring

diagram before making any electrical connections to the

unit. See the unit wiring label or

Figure 14 (page 26), Figure

15 (page 28)

, Figure 16 (page 30), Figure 17 (page 32),

Figure 18 (page 34)

, Figure 19 (page 36), Figure 20 (page

38)

, Figure 21 (page 40), Figure 22 (page 42), Figure 23

(page 44) Figure 24 (page 46)

, & Figure 25 (page 48).

• Use caution when handling thisapplianceorremoving

components. Personal injury can occur from sharp metal

edges present in all sheet metal constructed equipment.

4

REQUIREMENTS & CODES

• Thisequipmentmustbeinstalledinaccordancewith

instructions outlined in this manual and all applicable

local building codes.

• Allelectricalwiringmustbecompletedinaccordancewith

local, state and national codes and regulations and with

the National Electric Code (ANSI/NFPA 70) or in Canada

the Canadian Electric Code Part 1 CSA C.22.1.

• The installer must comply with all local codes and

regulations which govern the installation of this type of

equipment. Local codes and regulations take precedence

over any recommendations contained in these instructions.

Consult local building codes and the National Electrical

Code (ANSI CI) for special installation requirements.

• AirDuctsmustbeinstalledinaccordancewiththestandards

of the National Fire Protection Association “Standards for

Installation of Air Conditioning and Ventilation Systems”

(NFPA 90A), “Standard for Installation of Residence Type

Warm Air Heating and Air Conditioning Systems” (NFPA

90B), these instructions, and all applicable local codes.

• Consult

Table 2 (page 11), and the rating plate for the proper

circulating air ﬂow and temperature rise. It is important that

the duct system be designed to provide the correct ﬂow

rates and external pressure rise. An improperly designed

duct system can result in nuisance shutdowns, and comfort

or noise issues.

• This unitis designedforoutdoor installations only and

should be located as described on

page 4.

• Theinformationlistedbelowisforreferencepurposesonly

and does not necessarily have jurisdiction over local or

state codes. Always consult with local authorities before

installing this appliance.

Duct Systems

• USandCANADA:AirConditioningContractorsAssociation

(ACCA) Manual D, Sheet Metal and Air Conditioning

Contractors National Association (SMACNA), or American

Society of Heating, Refrigeration, and Air Conditioning

Engineers (ASHRAE) Fundamentals Handbook

Electrical Connections

• US:NationalElectricalCode(NEC)ANSI/NFPA70

• CANADA:CanadianElectricalCodeCSAC22.1

General Installation

• US:CurrenteditionoftheNFPA90B.Forcopies,contact

the National Fire Protection Association Inc., Batterymarch

Park, Quincy, MA 02269; or American Gas Association,

400 N. Capitol, N.W., Washington DC 20001 or www.

NFPA.org

• CANADA:NSCNGPIC.Foracopy,contactStandardSales,

CSA International, 178 Rexdale Boulevard, Etobicoke

(Toronto), Ontario, M9W 1R3 Canada

Safety

• US: (NFGC) NFPA 54–1999/ANSI Z223.1 and the

Installation Standards, Warm Air Heating and Air

Conditioning Systems ANSI/NFPA 90B.

• CANADA: CAN/CSA-B149.1 and .2–M00 National

Standard of Canada. (NSCNGPIC)

GENERAL INFORMATION

About the Rooftop Unit

Single Package Electric Cooling Rooftop Units are designed

only for outdoor rooftop or ground level installations and can

be readily connected to the duct system of a building.

This unit has been tested for capacity and efﬁciency in

accordance with AHRI Standards and will provide many

years of safe and dependable comfort, providing it is properly

installed and maintained. With regular maintenance, this unit

will operate satisfactorily year after year. Abuse, improper

use, and/or improper maintenance can shorten the life of

the appliance and create unsafe hazards.

To achieve optimum performance and minimize equipment

failure, it is recommended that periodic maintenance be

performed on this unit. The ability to properly perform

maintenance on this equipment requires certain tools and

mechanical skills.

Before You Install this Equipment

√ The cooling load of the area to be conditioned must be

calculated and a system of the proper capacity selected.

It is recommended that the area to be conditioned be

completely insulated and vapor sealed.

√ Check the electrical supply and verify the power supply

is adequate for unit operation. Consideration should be

given to availability of electric power, service access, noise,

and shade. If there is any question concerning the power

supply, contact the local power company.

√ All units are securely packed at the time of shipment and

upon arrival should be carefully inspected for damage prior

to installing the equipment at the job site. Verify coil ﬁns

are straight. If necessary, comb ﬁns to remove ﬂattened

or bent ﬁns. Claims for damage (apparent or concealed)

should be ﬁled immediately with the carrier.

√ Please consult your dealer for maintenance information and

availability of maintenance contracts. Read all instructions

before installing the unit.

Locating the Unit

• Surveythejobsitetodeterminethebestlocationforthe

packaged unit. The unit should be located with consideration

of minimizing the length of the supply and return ducts.

If practical, place the equipment and its ducts in an area

where they will be shaded from the afternoon sun, when

the heat load is greatest.

• ForHorizontalinstallations:selectasolid,levelposition,

preferably on a concrete slab, slightly above the grade

level, and parallel to the building.

• Overheadobstructions,poorlyventilatedareas,andareas

subject to accumulation of debris should be avoided. Do

not place the unit in a conﬁned space or recessed area

where discharge air from the unit could re-circulate back

through the condenser coil.

• Sufcientclearanceforunobstructedairowthroughthe

louvered control access panel and outdoor coil must be

maintained in order to achieve rated performance. See

Figure 1 (page 5) for minimum clearance requirements.

• If minimum clearances to combustibles are greater

than recommended serviceability clearances, then

clearances to combustibles must take precedence.

5

Heating Load

This unit should be sized to provide the design heating

load requirement. Heating load estimates can be made

using approved methods available from Air Conditioning

Contractors of America (Manual N); American Society of

Heating, Refrigerating, and Air Conditioning Engineers; or

other approved engineering methods.

CIRCULATING AIR SUPPLY

WARNING:

Do not allow combustion products from other

equipment or building vents to enter the return

air ductwork or the circulating air supply. Failure

to prevent products of combustion from being

circulated into the living space can create

potentially hazardous conditions including

carbon monoxide poisoning that could result in

personal injury or death.

All return ductwork must be adequately sealed,

all joints must be taped, and the ductwork must

be secured to the unit with sheet metal screws.

When return air is provided through the bottom

of the unit, the joint between the unit and the

return air plenum must be air tight.

The roof curb or cement pad that the unit is

mounted to must provide sound physical support

of the unit with no gaps, cracks, or sagging

between the unit and pad.

Return air and circulating air ductwork must not

be connected to any other heat producing device

such as a ﬁreplace insert, stove, etc. Doing so

may result in ﬁre, explosion, carbon monoxide

poisoning, personal injury, or property damage.

This unit is designed only for use with a supply and return

duct. Air ducts should be installed in accordance with

the standards of the National Fire Protection Association

“Standard for Installation of Air Conditioning Systems” (NFPA

Figure 1. Unit Clearance Requirements

Top of unit

to be

unobstructed

Recommended Clearances

for Service or Accesories

Minimum Required

Clearances to Combustibles

36"

48"

60"

48"

90A), “Standard for Installation of Residence Type Warm Air

Heating and Air Conditioning Systems” (NFPA 90B), and all

applicable local codes. NFPA publications are available by

writingto:NationalFireProtectionAssociation,Batterymarch

Park,Quincy,ME02269orvisittheirwebsite:www.NFPA.org.

• DesigntheductworkaccordingtoManualQbytheAir

Conditioning Contractors of America (ACCA) or similar

commercial methods.

• Ifroofcurbisinstalled,theductsmustbeattachedtothe

curb hangers, not the unit.

• Ductworkshouldbeattacheddirectlytotheunitendpanel

for horizontal applications.

• Ifacombinationofindoorandoutdoorairisused,theducts

and damper system must be designed so that the return

air supply to the furnace is equal to the return air supply

under normal, indoor return air applications.

• Thisunitisshippedreadyforverticalductconnections

and is easily converted for horizontal duct connections.

Unconditioned Spaces

All ductwork passing through unconditioned space must be

properly insulated to prevent condensation and minimize duct

losses. Use insulation with an outer vapor barrier. Refer to

local codes for insulation material requirements.

Acoustical Ductwork

Certain installations may require the use of acoustical lining

inside the supply duct work.

• Acoustical insulation must be in accordance with the

current revision of the Sheet Metal and Air Conditioning

Contractors National Association (SMACNA) application

standard for duct liners.

• DuctliningmustbeULclassiedbattsorblanketswitha

ﬁre hazard classiﬁcation of FHC-25/50 or less.

• Fiberductworkmaybeusedinplaceofinternalductliners

if the ﬁber duct work is in accordance with the current

revision of the SMACNA construction standard on ﬁbrous

glass ducts. Fibrous duct work and internal acoustical

lining must be NFPA Class 1 air ducts when tested per

UL Standard 181 for Class 1 ducts.

Air Filter Requirements

WARNING:

Never operate the unit without a ﬁlter in place.

Dust and lint could accumulate on internal parts,

resulting in loss of efﬁciency, equipment damage

and possible ﬁre.

All return air must pass through the ﬁlters before entering the

unit. It is important that all ﬁlters be kept clean and replaced

frequently to ensure proper operation of unit. Dirty or clogged

ﬁlters will reduce the efﬁciency of the unit and result in unit

shutdowns. Air ﬁlter pressure drop must not exceed 0.08

inches WC. When replacing the air ﬁlters, a suitable air ﬁlter

must be installed ahead of the evaporator coil of the return

air system. Refer to

Table 1 for recommended ﬁlter sizes.

Table 1. Filter Sizes & Quantities

UNIT

FACTORY

FILTER SIZE

QTY

P7TQ-072 20 x 20 x 2 4

P7TQ-090 20 x 20 x 2 4

P7TQ-120 20 x 20 x 2 4

6

UNIT INSTALLATION

Packaging Removal

All units have been securely packaged at the point of shipment.

After unpacking the unit, carefully inspect for apparent and

concealed damage. Claims for damage should be ﬁled with

the carrier by the consignee.

1. Remove any shipping brackets. DO NOT remove base

rails from unit.

2. Inspect unit thoroughly for shipping damage.

3. Carefully lower and position unit to its permanent location.

Rigging & Hoisting

WARNING:

To avoid the risk of property damage, personal

injury, or death, it is the rigger’s responsibility

to ensure that whatever means are used to hoist

the unit are safe and adequate:

• Theliftingequipmentmustbeadequateforthe

load. Refer to

Table 4 (page 17) for unit weights.

• Theunit must beliftedfrom the holesinthe

base rails using cables or chains.

• Spreaderbarsarerequiredtoprotecttheunit

and ensure even loading. See

Figure 2.

• Keeptheunitinanuprightpositionatalltimes.

The rigging must be located outside the unit’s

center of gravity. Refer to

Table 4 (page 17) for

locating the center of gravity.

• All panels must be securely in place during

rigging and hoisting.

Minimum Clearance Requirements

P7TQ units are certiﬁed as combination heating and cooling

equipment for outdoor installation only.

Figure 1 (page 5)

displays the minimum clearances to combustible materials

for both Downﬂow and Horizontal discharge.

P7TQ units may be installed on non-combustible surfaces

when used with bottom supply and return air ducts. Units

may be installed on wood ﬂooring or on Class A, B, or C

roof covering material as long as the following requirements

aremet:

• Ifusingsidesupplywithreturnairducts,theunitmustbe

converted for horizontal connections. Refer to Vertical to

Horizontal section below. NOTE: This must be converted

prior to unit installation.

• Ifusingverticaldischargeandreturnairductsaroofcurb

must be installed prior to unit installation. See Rigging and

Hoisting section

(page 6) for setting of the unit.

Vertical to Horizontal Conversion

The unit is shipped ready for downﬂow duct connections.

If horizontal ducts are required, the unit must be converted

prior to attaching duct work to unit.

1. Remove both return and supply horizontal duct covers.

Do not discard the screws or covers. These will be used

to cover the openings in the bottom of the unit. See

Figure

3

.

2. Cut both return and supply openings following along the

tabbed cutouts. NOTE: There are tabs on the inside and

the outside of the panels. Discard the cut sections when

done. These will not be needed.

Figure 4.

IMPORTANT NOTE:

Use caution when cutting left vertical side of return air

panel. The ﬁlter rack is in close proximity to opening

3. Install the duct covers (removed in step 1) over the openings

in the bottom of the unit. NOTE: Apply adhesive around

the perimeter of both openings before setting the duct

covers into position.

4. Align the predrilled locating holes and secure the duct

covers with screws removed in step 1.

Figure 2. Rigging & Hoisting

LIFTING

BEAM

CABLE OR CHAIN

SPREADER

BAR

SPREADER

BAR

BASE

RAIL

BASE

RAIL

Figure 3. Vertical to Horizontal conversion

(Right side view)

Covers removed

Exposing area for

cutouts-connecting tabs

Figure 4. Cutouts removed

(Right Side view)

7

Rooftop Mounting

Rooftop installations must be located according to local

buildingcodesorordinancesandtheserequirements:

• Theroofmustbecapableofhandlingtheweightofthe

unit. For unit weights, see

Table 4 (page 17). Reinforce

the roof if necessary.

• The appropriate accessory roof curb

Figure 5 (page 7)

must be installed prior to unit installation. The roof curb

must be square and level to ensure proper condensate

drainage. Please follow all instructions provided with

the kit.

WARNING:

Never drill or punch holes in unit base when

installing downﬂow units. Leakage may occur if

bottom pan is punctured.

• Onbottomdischargeapplications,thesupplyandreturn

air ducts must be attached to the roof curb duct supports,

not the unit. Install all ductwork before setting unit on curb

or frame.

• Framesupportmustbeconstructedusingnoncombustible

materials. Full perimeter support is required under the

unit. Supports must be made of steel or weather resistant

wooden materials. The unit must be square and level to

ensure proper condensate drainage.

• The frame must be high enough to ensure prevention

of any moisture from entering the unit. Recommended

height to unit base is 8” for both downﬂow and horizontal

installations.

• Secure roof curb or frame to roof using acceptable

mechanical methods per local codes.

Ground Level

Ground level installations must be located according to local

buildingcodesorordinancesandtheserequirements:

• Clearancesmustbeinaccordancewiththoseshownin

Figure 1 (page 5).

• Amountingpad

Figure 6 (page 7) must be provided and

separate from the building foundation. The pad must be

level to ensure proper condensate disposal and strong

enoughtosupporttheunit’sweight.Theslabheightmust

be a minimum of 3” (8 cm) above grade and with adequate

drainage.

• Whenusinghorizontalsupplywithreturnairducts,theunit

must be converted for horizontal connections prior to unit

installation. Refer to the Vertical to Horizontal Conversion

section on

page 6.

Condensate Drain

The method for disposing of condensate varies according

to local codes. Consult your local code or authority having

jurisdiction.

Condensate is drained from the unit through a 3/4” (19 mm)

PVC pipe located on end of the unit (

Figure 7). For proper

drainage, install a 3” (8 cm) Min. trap between the drain

line and an open vent of the same size. Avoid areas where

condensate drainage may cause problems.

The condensate drain line must be J-trapped using ﬁeld

supplied parts and may be combined with other drain lines

when routed to the drain.

When connecting rigid drain line, hold any ﬁttings with a

wrench to prevent twisting. Do not overtighten!

Figure 5. Roof Curb

See Table

3

Roof Curb

Figure 6. Mounting Pad

3”

Condensate

Drain

Figure 7. Condensate Drain

8

• Useonlycopperwireforthelinevoltagepowersupply

to this unit. Use proper code agency listed conduit and

connector for connecting the supply wires. Use of rain

tight conduit is recommended.

• Unitsareshippedfromthefactorywiredfor230or460volt

operation. On 208-230V units being placed into 208 volt

operation, remove the lead from the transformer terminal

marked 240V and connect it to the terminal marked 208V.

• Overcurrent protection mustbeprovidedat the branch

circuit distribution panel and sized as shown on the unit

rating label and according to the National Electric Code

and applicable local codes. NOTE: See the unit rating plate

for maximum circuit ampacity and maximum overcurrent

protection limits.

Grounding

WARNING:

The unit cabinet must have an uninterrupted or

unbroken electrical ground to minimize personal

injury if an electrical fault should occur. Do not

use gas piping as an electrical ground

!

This unit must be electrically grounded in accordance with

local codes or, in the absence of local codes, with the National

Electrical Code (ANSI/NFPA 70) or the CSA C22.1 Electrical

Code. Use the grounding lug provided in the control box for

grounding the unit.

Unbalanced 3-Phase Supply Voltage

Voltage unbalance occurs when the voltages of all phases

of a 3-phase power supply are no longer equal. This

unbalance reduces motor efﬁciency and performance. Some

underlyingcausesofvoltageunbalancemayinclude:Lack

of symmetry in transmission lines, large single-phase loads,

and unbalanced or overloaded transformers. A motor should

never be operated when a phase imbalance in supply is

greater than 2%.

Perform the following steps to determine the percentage of

voltageimbalance:

1. Measure the line voltages

of your 3-phase power

supply where it enters the

building and at a location

that will only be dedicated

to the unit installation. (at

the units circuit protection

or disconnect).

EXAMPLE:

AB = 451V

BC = 460V

AC = 453V

2. Determine the average voltage in the power supply.

In this example, the measured line voltages were 451, 460,

and 453. The average would be 454 volts (451 + 460 +

453 = 1,364 / 3 = 454).

ELECTRICAL WIRING

WARNING:

ELECTRICAL SHOCK, FIRE OR

EXPLOSION HAZARD

Failure to follow safety warnings exactly could

result in serious injury or property damage.

Improper servicing could result in dangerous

operation, serious injury, death or property

damage.

• Before servicing, disconnect all electrical

power to furnace.

• Whenservicingcontrols,labelallwiresprior

to disconnecting. Reconnect wires correctly.

• Verifyproperoperationafterservicing.

Pre-Electrical Checklist

√ Verify that the voltage, frequency, and phase of the supply

source match the speciﬁcations on the unit rating plate.

√ Verify that the service provided by the utility is sufﬁcient

to handle the additional load imposed by this equipment.

For proper MCA / MOP data see the unit wiring label or

Table 13 (page 50) or Table 14 (page 51).

√ Verify factory wiring is in accordance with the unit wiring

diagram. Inspect for loose connections.

√ For 3 phase units always check the phase balance. See

page 8.

Line Voltage

• Electrical connections must be in compliance with all

applicable local codes and ordinances, and with the current

revision of the National Electric Code (ANSI/NFPA 70).

For Canadian installations the electrical connections and

grounding shall comply with the current Canadian Electrical

Code (CSA C22.1 and/or local codes).

• Providepowersupplyfortheunitinaccordancewiththe

unit wiring diagram and the unit rating plate. The line

voltage to the unit should be supplied from a dedicated

branch circuit containing the correct fuse or circuit breaker

for the unit.

• An electrical disconnect must be located within sight

of and readily accessible to the unit. This switch shall

be capable of electrically de-energizing the outdoor unit.

See unit data label for proper incoming ﬁeld wiring. Any

other wiring methods must be acceptable to authority

having jurisdiction.

• Awiringdiagramislocatedontheinsidecoverofthecontrol

access panel of the outdoor unit. The installer should

become familiar with the wiring diagrams before making

any electrical connections to the outdoor unit. See

Figure

14 (page 26)

, Figure 15 (page 28), Figure 16 (page 30),

Figure 17 (page 32), Figure 18 (page 34), Figure 19 (page

36)

, Figure 20 (page 38), Figure 21 (page 40), Figure

22 (page 42)

, Figure 23 (page 44), Figure 24 (page 46),

&

Figure 25 (page 48).

• Ifanyoftheoriginalwiressuppliedwiththeunitmustbe

replaced, they must be replaced with material of the same

voltage, gauge, and temperature rating.

• Connect the line-voltageleads to the terminals on the

3-pole terminal block (inside the control compartment).

9

3.Determinethemaximumdeviation:

EXAMPLE

From the values given in step 1, the BC voltage (460V) is

thegreatestdifferenceinvaluefromtheaverage:

460 - 454 = 6

454 - 451 = 3

454 - 453 = 1

4. Determine percent of

voltage imbalance by

using the results from

steps 2 & 3 in the following

equation.

6

454

100 x

= 1.32%

EXAMPLE

maxvoltage deviation

fromaverage voltage

=100 x

averagevoltage

% Voltage

Imbalance

The amount of phase imbalance (1.32%) is satisfactory

since the amount is lower than the maximum allowable 2%.

Please contact your local electric utility company if your

voltage imbalance is more than 2%.

Thermostat / Low Voltage Connections

• SinglePackageElectricHeating/ElectricCoolingRooftop

Units are designed to operate with a 24 VAC Class II

control circuit. The control circuit wiring must comply with

the current provisions of the NEC (ANSI/NFPA 70) and

with applicable local codes having jurisdiction. Thermostat

connections should be made in accordance with the

instructions supplied with the thermostat.

• Atwo-stagecoolingthermostatisrequiredforP7TQseries

units. Select a thermostat which operates in conjunction

with the installed accessories. See Figure 10 for proper

wire gauge and their recommended lengths for typical

thermostat connections.

• Thelowvoltagewiresmustbeproperlyconnectedtothe

units low voltage terminal block. Route 24V control wires

through the side of the unit. Recommended wire gauge

and wire lengths for typical thermostat connections are

shown in

Figure 8.

• Thethermostatshouldbemountedabout5feetabovethe

ﬂoor on an inside wall. DO NOT install the thermostat on

an outside wall or any other location where its operation

may be adversely affected by radiant heat from ﬁreplaces,

sunlight, or lighting ﬁxtures, and convective heat from

warm air registers or electrical appliances. Refer to the

thermostatmanufacturer’sinstructionsheetfordetailed

mounting information.

Heat Anticipator

Verify if the thermostat being used for the installation has a

heat anticipator setting. This function allows the thermostat to

anticipate the space heating rate and time the burner to shutoff

accordingly.Alwaysrefertothethermostatmanufacturer’s

instructions for the correct settings.

Blower Speed

The blower speed is preset at the factory but must be veriﬁed

at each installation. For optimum system performance and

comfort, it may be necessary to change the factory set speed.

Refer to

Table 5 (page 19), Table 6 (page 20), Table 7 (page

21)

, Table 8 (page 22), Table 9 (page 23), Table 10 (page

24)

, Table 11 (page 25), & Table 12 (page 25) for proper

blower performance data. Always ensure drive belt is secure

and tensioned properly. Also inspect variable pitch sheaves

for proper tightness of the set screws

CAUTION:

To avoid personal injury or property damage,

make certain that the motor leads do not make

contact with any uninsulated metal components

of the unit.

Tochangetheblowerspeed:

1. Disconnect all electrical power to the unit and open

the blower access door.

2. Loosen the motor mounting nuts and mounting plate

adjustment bolt to allow removal of the blower belt from

the motor sheave.

3. Loosen top set screw on motor sheave and turn clockwise

to close (increases blower speed), or counterclockwise to

open (decreases blower speed).

4. Replace belt on pulleys and position motor mounting plate

to correct position for proper belt tension.

5. Tighten motor nuts.

Figure 8. Typical 2 - Stage Heat/Cool

Thermostat Connection

T-Stat Wire

Gauge

Recommended T-Stat Wire

Length - Ft. (Unit to T-Stat)

18 Ga. 0 - 60

16 Ga. 61 - 130

Field Supplied Wiring - - - - - Use Solid Class II Copper Wire

Y1

Y2

W2

W1

G

RH

RC

Y1

Y2

W2

W1

G

R

Indoor

Thermostat

Sub-Base

Unit Low Voltage

Terminal

A1

Economizer

OCC/UNOCC

Stage 1 Cool

Stage 2 Cool

Stage 1 Heat

Blower

24V Hot

10

STARTUP & ADJUSTMENTS

Pre-Start Check List

√ Verify unit is properly supported.

√ Verify unit is level for proper condensate drainage.

√ Verify all clearance requirements are met. Airﬂow to and

from the outdoor coil must be unrestricted.

√ Verify the ductwork is adequately sealed to prevent air

leakage. Insulate if necessary.

√ Verify the line voltage power leads are securely connected

and the unit is properly grounded.

√ Verify low voltage wires are securely connected to the

correct leads in the low voltage area of the control box.

√ Verify the indoor blower is properly set for the installation.

√ Verify the outdoor fan turns freely.

√ Verify the power supply branch circuit overcurrent protection

is properly sized.

√ Verify all exterior panels have been reinstalled and securely

fastened.

√ Verify the thermostat is wired correctly and preset for initial

operation. Set the thermostat system switch to OFF and

the fan switch to AUTO.

Startup Procedures

WARNING:

This unit is equipped with crankcase heaters.

Allow 24 hrs for heating of the refrigerant

compressor crankcase prior to start up and

anytime the power has been removed for more

than 12 hrs. Failure to comply may result in

damage or cause premature failure of the system.

IMPORTANT NOTE:

Failure to follow the crankcase heater instructions for

units equipped with microchannel coils may lead to a

discharge pressure spikes which could cause the unit

high pressure switch to trip. If this occurs, wait for unit

pressures to equalize before depressing the manual

reset switch and re-start the unit again.

• Checkallelectricalwiringforlooseconnectionsandtighten

as required.

• Checkunitforreturnairltersandcondensatetrap.

• Closeallelectricaldisconnectstoenergizethesystem.

Air Circulation

1. Set thermostat system switch to OFF and the fan switch

to ON.

2. Verify the blower motor runs continuously. Check for

air delivery at the register(s). Ensure that there are no

obstructions at the registers or in the ductwork.

3. Set thermostat fan switch to AUTO and verify the blower

shuts down immediately.

NOTE: If blower is turning opposite of arrow direction, shut

off main power to the unit and switch any two ﬁeld wires at

the disconnect. DO NOT alter unit wiring.

System Cooling

1. Set the thermostat system switch to COOL and the fan

switch to AUTO.

2. Lower the thermostat temperature switch below room

temperature and observe that the blower, both compressors

and fans) energize.

3. Verify blower is turning in direction indicated by arrow

and air discharged at the register is cooler than room

temperature.

4. Verify HI and LO refrigerant pressures.

NOTE: If refrigerant pressures are abnormal and blower

is rotating in the opposite direction of the arrow, shut off

main power to the unit and switch any two ﬁeld wires at the

disconnect. Ensure proper rotation of the blower. DO NOT

alter unit wiring. Listen for any unusual noises. Locate the

source and correct as needed.

5. Allow the unit to run for several minutes. Set the temperature

selector above room temperature and verify that the fan,

blower, and compressors cycle off with the thermostat.

System Heating - Field Installed Electric Heat

This packaged air conditioner is designed to allow an optional

electric heat kit to be ﬁeld installed as required by the

building’sparticularheatingload.Theoptionsavailablefor

each unit are shown in the heater kit installation instructions

orunit’sTechnicalServiceLiterature.Installtheheaterkitsas

directed by the instruction manual provided with the heater

kit. Follow all cautions and warnings as directed. Use only

factory authorized heater kits.

WARNING:

Uninsulated live components are exposed when

control access panel is removed.

1. Set the thermostat to above room temperature.

2. Verify that the compressor and outdoor fan motor are not

energized and the electric heat is energized.

3. After the unit has run for approximately ﬁve minutes, set

the thermostat below room temperature and verify that

the electric heat has de-energized.

Verifying Temperature Rise

1. Place thermometers in the return and supply air stream

as close to the unit as possible. The thermometer on the

supply air side must be shielded against direct radiation

from the electric heat elements to avoid false readings.

2. Adjust all registers and duct dampers to the desired

position. Run the unit for 10 to 15 minutes before taking

any temperature readings. The temperature rise is the

difference between the supply and return air temperatures.

NOTE: For typical duct systems, the temperature rise will fall

near the value speciﬁed in the temperature rise table (with

the blower speed at the factory recommended setting). See

Table 2 (page 11). If the measured temperature rise falls

outside the speciﬁed rise, it may be necessary to change

the blower speed. Lowering the blower speed increases

the temperature rise and a higher speed decreases the

temperature rise.

Verifying Operation of Over-Temperature Limit

Control (Field Installed Electric Heat)

To verify operation of the over-temperature limit control, make

sure the louvered control access panel is in place and that

there is power to the unit.

1. Block the return airﬂow to the unit by installing a close-off

plate in place of or upstream of the ﬁlter.

2. Set the thermostat above room temperature and verify the

unit operates with the correct sequence of operation. See

Operating Sequence (

page 11).

11

TROUBLESHOOTING

If the unit does not operate properly in the cooling mode,

checkthefollowing:

• Thethermostatisoperatingproperly.

• Electricalpowertotheunitisturnedon.

• Allsafetyswitchesareclosed.

• Theservicedoorsareinplace.

• Transformercircuitbreakerisreset.

If the unit does not operate properly in the heating mode,

checkthefollowing:

• Thethermostatisoperatingproperly.

• Electricalpowertotheunitisturnedon.

• Allsafetyswitchesareclosed.

• Theservicedoorsareinplace.

• Transformercircuitbreakerisreset.

REFRIGERANT CHARGING

WARNING:

If repairs make it necessary for evacuation and

charging, it should only be done by qualiﬁed,

trained personnel thoroughly familiar with this

equipment. Some local codes require licensed

installation/service personnel to service this type

of equipment. Under no circumstances should

the owner attempt to install and/or service this

equipment.

Failure to comply with this warning could result

in property damage, personal injury, or death.

The P7TQ Series packaged electric units are fully charged

at the factory and when installed accordingly, no charging

is required. The refrigerant charge can be checked and

adjusted through the service ports provided on the units.

Use only gauge lines which have a “Schrader” depression

device present to actuate the valve.

Refrigerant charging must be done by qualiﬁed personnel

familiar with safe and environmentally responsible refrigerant

handling procedures. See Unit Rating Plate for the proper

type and amount of refrigerant.

NOTE: The over-temperature limit control should function

to turn off the electric heat within approximately 1-2 minutes

(exact time depends on the efﬁciency of the close-off when

blocking the return air). The circulating air blowers should

continue to run when the over-temperature limit control

switch opens.

3. Remove the close-off plate immediately after the over-

temperature limit control opens. If the unit operates for

more than four minutes with no return air, set the thermostat

below room temperature, shut off power to the unit, and

replace the over-temperature limit control.

OPERATING SEQUENCE

The operating sequences for the heating, cooling, and fan

modesaredescribedbelow.Refertothewiringdiagrams:

Figure 14 (page 26), Figure 15 (page 28), Figure 16 (page

30)

, Figure 17 (page 32), Figure 18 (page 34), Figure 19

(page 36)

, Figure 20 (page 38), Figure 21 (page 40), Figure

22 (page 42)

, Figure 23 (page 44) Figure 24 (page 46), &

Figure 25 (page 48).

Cooling Mode

1. On a call for cooling the thermostat closes, applying 24

VAC to Y1, G, & Y2 if Stage 2 cooling is calling.

2. G applies 24VAC to the main circulating blower circuit.

3. Y1 & Y2 apply 24VAC through all safety switches before

energizing their respective contactors.

4. When the thermostat is satisﬁed the contactors are de-

energized.

5. The circulating blower motor de-energizes immediately.

Heating Mode (Optional Electric Heat)

1. On a call for heat, the thermostat closes, applying 24 VAC

to the W1 terminal and the circulating blower circuit.

2. When the thermostat is satisﬁed the contactors are de-

energized.

3. The circulating blower motor de-energizes immediately.

Blower Mode

1. On a call for fan operation, the thermostat applies 24 VAC

directly to the blower contactor.

2. The circulating blower is energized immediately.

Unit Fails to Operate

If the unit does not operate properly in either the heating or

coolingmode,becertaintocheckthefollowing:

1. The thermostat is operating properly.

2. Electrical power to the unit is turned on.

3. All safety switches are closed.

4. The service doors are in place.

5. Transformer circuit breaker is reset.

Table 2. Heat Rise and Range

MODEL

NUMBER

NOMINAL

RATED CFM

* TEMPERATURE RISE °F (°C)

9 KW 18 KW 30 KW 35 KW

P7TQ072-* 2550 11° F (6° C) 22° F (12° C) 37° F (21° C) 43° F (24° C)

P7TQ090-* 3150 9° F (5° C) 18° F (10° C) 30° F (17° C) 35° F (19° C)

P7TQ120-* 3450 8° F (4° C) 16° F (9° C) 27° F (15° C) 32° F (18° C)

* Temperature Rise calculation = Rise (°F) = (kW*3413) / 1.08 / Nominal CFM.

NOTE: For 208-230V electric heat kits operating @ 208 Volts, the Kw rating is derated 25%, therefore temperature rise will be lower than the

values in the table.

12

NOMINAL TONNAGE STAGE 1 CHARGE LEVEL STAGE 2 CHARGE LEVEL

6 128 Oz. N/A

7 1/2 93 Oz. 94 Oz.

10 97 Oz. 94 Oz.

NOTE: If unit is unable to operate within above guidelines and equipped with an adjustable TXV, the TXV can be adjusted (not

recommended) by turning CW to close (increase sub-cooling) and CCW to open (lower sub-cooling).

Table 3. Refrigerant Charge Table

Charging Charts & Application Notes

Thisequipment’scoolingsystemscontainrefrigerantunder

high pressure, always use safe practices when servicing the

unit. Always review the factory literature and safety warnings

prior to servicing.

All P7TQ units are shipped from the factory with the proper

amount and type of refrigerant. Always inspect the unit rating

labeltodeterminetheunit’sinformationpriortoworkingon

the system. Do not mix different refrigerants or charge the

unit with a refrigerant not listed on the unit rating label.

The charging charts are valid for a variety of indoor, return

air conditions and are most highly inﬂuenced by the outdoor

ambient temperature, outdoor fan operation and the unit

operating voltage. Before referencing the charts, always

ensure that all compressor circuits are energized and have

stable operation. As can be seen in the charging charts, the

ideal system sub-cooling can vary over the range of operation.

Always reference the charts to determine the ideal amount of

sub-cooling for a given liquid pressure. See

Figure 9, Figure

10

, & Figure 11 (page 13). Units charged to other values will

not perform at the rated unit efﬁciency (EER). See

Table 3.

To inspect a systems operation, using quality instruments,

match the measured liquid temperature to the units chart.

The measured liquid pressure reading should be within 3%

of the value shown for most installations. For two stage

systems, the charts are valid for both compressor stages.

Do not utilize the charts for two stage systems operating

only under a single stage call for cooling.

Do not utilize the charts in systems that do not have all the

outdoor fans energized, or have the fans cycling under a

low-ambient control. Refer to the low-ambient kit instructions

for more information, if applicable.

For systems that are operating with more than a 5% deviation,

inspect the unit for leaks ﬁrst and see Note in

Table 3. Always

use safe and environmentally sound methods for refrigerant

handling. When repairing system leakages, always utilize

a nitrogen (inert) gas to protect the refrigerant system and

pressure check the repair before re-charging. Always replace

the ﬁlter-dryers when performing any repair to the refrigeration

system. After completing the repairs, evacuate the system to

350-500 microns and weight in the refrigerant to the amount

speciﬁed on the unit rating label.

160

180

200

220

240

260

280

300

320

340

360

380

400

420

440

460

480

500

520

540

560

50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125

130

Liquid Pressure (PSIG)

Liquid Temperature (Deg. F)

P7TQ-072 Charging Chart - Cooling

(Both stages operating)

High Speed

Remove refrigerant when above curve

Add refrigerant when below curve

Figure 9. P7TQ-072 Charging Chart (6-Ton)

13

160

180

200

220

240

260

280

300

320

340

360

380

400

420

440

460

480

500

520

540

560

50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125

130

Liquid Pressure (PSIG)

Liquid Temperature (Deg. F)

P7TQ-090 Charging Chart - Cooling

(Both stages operating)

Remove refrigerant when above curve

Add refrigerant when below curve

Stage 1

Stage 2

Figure 10. P7TQ-090 Charging Chart (7.5-Ton)

160

180

200

220

240

260

280

300

320

340

360

380

400

420

440

460

480

500

520

540

560

50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125

130

Liquid Pressure (PSIG)

Liquid Temperature (Deg. F)

P7TQ-120 Charging Chart - Cooling

(Both stages operating)

Add refrigerant when below curve

Remove refrigerant when above curve

Stage 2

Stage 1

Figure 11. P7TQ-120 Charging Chart (10-Ton)

14

UNIT MAINTENANCE

WARNING:

ELECTRICAL SHOCK, FIRE OR

EXPLOSION HAZARD

Failure to follow safety warnings exactly could

result in serious injury or property damage.

Improper servicing could result in dangerous

operation, serious injury, death or property

damage.

• Before servicing, disconnect all electrical

power to furnace.

• Whenservicingcontrols,labelallwiresprior

to disconnecting. Reconnect wires correctly.

• Verifyproperoperationafterservicing.

NOTE: These maintenance instructions are primarily intended

to assist qualiﬁed technicians experienced in the proper

maintenance and operation of this appliance.

To achieve optimum performance from the air conditioner

and minimize equipment failure, it is recommended that

periodic maintenance be performed on this unit. The ability

to properly perform maintenance on this equipment requires

certain mechanical skills and tools. Please consult your dealer

for maintenance information and availability of maintenance

contracts.

Routine Maintenance

Please consult your dealer for maintenance information and

availability of maintenance contracts. At a minimum, routine

maintenanceshouldincludethefollowingitems:

CAUTION:

Use care when removing parts from this unit.

Personal injury can result from sharp metal

edges present in all equipment of sheet metal

construction.

Air Filters

WARNING:

Never operate the unit without ﬁlters in place. Dust

and lint in the return air can build up on internal

components, resulting in loss of efﬁciency,

equipment damage, and possible ﬁre.

It is recommended that the air ﬁlters be inspected and cleaned

or replaced every three to four weeks using ﬁlters of like size

and kind.

Table 1 (page 5) lists the factory installed ﬁlter

sizes and quantities for each unit. NOTE: P7TQ units are

equipped with 2” pleated disposable ﬁlters.

Blower Compartment

Buildup of dirt and lint on the blower and motor can create

excessive loads on the motor resulting in higher than normal

operating temperatures and possible shortened service life.

It is recommended that the blower compartment be cleaned

monthly during heating and cooling seasons to remove any

dirt and lint that may have accumulated in the compartment

or on the blower and motor. Inspect the blower drive belt for

cracks, excessive wear and proper tension after cleaning

the compartment.

Condensate Drain & Outdoor Coil

Inspect the condensate drain and outdoor coil at the begin-

ning of each cooling season. Remove any debris. Clean the

outdoor coil and hail guard louvers (optional) as necessary

using a mild detergent and water. Rinse thoroughly with water.

Electrical

WARNING:

This unit may have more than one electrical

supply. To avoid risk of electrical shock, personal

injury, or death, disconnect all electrical power

to the unit before performing any maintenance

or service.

CAUTION:

Label all wires prior to disconnection when

servicing controls. Wiring errors can cause

improper and dangerous operation.

Inspect the electrical connections for tightness at the

beginning of each heating and cooling season. Service as

necessary.

Motor / Bearing Lubrication

WARNING:

Lubrication of the motors in this unit is not

required. Do not lubricate any motor in this

product.

• Theblowerassemblyinthisunitisequippedwithtwosupport

bearings. The support bearings are sealed cartridge units

and require no further lubrication.

• Theindoorblowermotorispre-lubricatedatthefactory

and does not require additional lubrication.

• Theoutdoorfanmotorsareequippedwithpre-lubricated

sealed ball bearings. No further oiling is required for the

life of this product

15

COMPONENT FUNCTIONS

The descriptions below are various functional components that affect the operation and shutting down of this unit. Some

of these components and their locations are shown in

Figure 12. If any component on this unit must be replaced, use only

factory authorized replacement parts speciﬁed in the Replacement Parts List provided online.

High Pressure Switch - This factory installed switch is designed to de-energize the unit when excessive pressure occurs

due to abnormal conditions. Under normal conditions, the switch is closed. If the discharge pressure rises above 650 psig,

then the switch will open and de-energize the outdoor unit. The switch is a manually reset type and will remain open until

the button on top of the switch is depressed.

Over-Temperature Limit Control (Optional Electric Heat)-The over-temperature limit control acts to prevent the air

temperature leaving the unit from exceeding the maximum outlet air temperature. If the limit opens, the blower limit relay

will energize. The circulating air blower will continue to operate if the over-temperature limit control opens.

Figure 12. Location of Unit Components

Electrical Control Panel

Single Point

Electrical Connection

Compressor(s)

Fuel Line Inlet

Blower

Return Air

Supply Air

Condensate Drain

Condenser

Fans

Exhaust

Vent

Base

Rails

Electric Heat

Inspection Cover

16

FIGURES & TABLES

Top View

Figure 13. Physical Dimensions for P7TQ Units

Rear View

Corner “D”

Corner “C”

Corner “A”

Corner “B”

88 3/4”

59 3/4”

54”

Lifting Fork Pockets

Front View

Return Air

36 3/8”

Supply Air

28 3/4”

14”

12 5/8”

Corner “D”

Corner “C”

Corner “A”

Corner “B”

Bottom Power Entry

8 1/8”

11 3/8”

6 1/4”27 3/16”

Bottom

Pan

(Top View)

17

Side View

Corners C & D

Corner “D” Corner “C”

96 1/4”

103 7/8”

P7TQ With Optional Hoods Installed

40 5/8”

40 3/8”

15”

15 1/8”

43 1/8”

36”

60 1/4”

A

B

CG

Figure 13. Continued

Corner “B”

Corner “A”

13 3/4”

30 1/2”

Lifting Fork Pockets

12 5/8”

5 3/16”

7 5/8”

Side View

Corners A & B

MODEL

NUMBER

UNIT

WEIGHT ‡

SHIPPING

WEIGHT

CENTER OF

GRAVITY

INCHES (MM)

CORNER WEIGHTS UNIT HEIGHT**

A B C D

HORIZONTAL

DUCT

APPLICATIONS

VERTICAL

DUCT

APPLICATIONS

LBS. KG. LBS. KG A B LBS. KG. LBS. KG. LBS. KG. LBS. KG.

P7TQ-072 1017 462 1139 517 50.5” 27.0” 232 105 362 164 302 137 199 90 54” 48.5”

P7TQ-090 1141 518 1263 574 46.5” 24.5” 291 132 346 157 298 135 249 113 54” 48.5”

P7TQ-120 1155 525 1277 580 46.5” 24.0” 275 125 347 157 319 145 246 112 54” 48.5”

**Baserails are not intended to be removed. Information provided is total unit height for horizontal duct applications or height dimension added to selected roof

curb height for vertical duct applications.

‡ Unit weight without packaging or ﬁeld installed accessories.

Table 4. Center of Gravity & Unit Shipping Weights

18

Blower Performance Data

This equipment is outﬁtted with a belt driven blower assembly in order to accommodate a large variety of duct conﬁgurations

and airﬂow selections. The blower has been factory inspected for proper alignment, operation and rotational direction prior

to the drive motor being situated in the shipping position. The blower drive belt is located with these instructions and must

be installed by the service technician.

The factory standard drive installed in these units has been set to deliver 350-400 Cfm/ton at an External Static Pressure

(ESP) of 0.25-0.30 in-Wg.

Table 5 (page 19), Table 6 (page 20), Table 7 (page 21), Table 8 (page 22), Table 9 (page 23),

Table 10 (page 24), Table 11 (page 25), & Table 12 (page 25) show the full blower curves of these drive conﬁgurations

and can be utilized to easily set the adjustable motor sheave for alternate conﬁgurations. Refer to the Legend below for a

description of the table information. After a sheave setting has been made, always inspect the blower amp draw to ensure

that it is less than the service factor amps listed on the motor.

For units being placed into service conﬁgured for horizontal ﬂow operation, make sure to note any required blower drive

belt or pulley changes.

3493

Factory Low Static Setting: Recommended operational point1017

2.07

3862

Medium Static Setting (Optional): Recommended operational point

1159

3.03

2946

Italic font Indicates an allowable setting that is not recommended for unit operation.

These operational points should be carefully examined by the installer for proper unit setup and heater operation if used.

741

0.85

Indicates a setting that is not permitted for unit operation

19

Table 5. P7TQ-072 C/D/N Series - Downﬂow Models

P7TQ072-C/D/N SERIES

2 HP, 2 SPEED DOWNFLOW BLOWER DATA

Factory Standard & Medium Static Drive

HIGH SPEED OPERATION

EXTERNAL

UNIT STATIC

(“ WC)

OPERATING @

230V, 460V, OR

575V

ADJUSTABLE MOTOR SHEAVE SETTING

FULLY

CLOSED

0.5 TURN

OPEN

1 TURN

OPEN

1.5 TURNS

OPEN

2 TURNS

OPEN*

2.5 TURNS

OPEN

3 TURNS

OPEN

3.5 TURNS

OPEN

4 TURNS

OPEN

4.5 TURNS

OPEN

5 TURNS

OPEN

0.1

CFM

2780

2703 2626 2538 2460 2455 2450

RPM 887 866 845 821 869 848 826

kW

1.27

1.17 1.07

1.08 1.31 1.15 0.98

0.2

CFM 2728 2640 2545 2450

2555 2330 2310 2290

RPM 907 888 867 846

895 870 849 827

kW 1.40 1.27 1.20 1.14

1.20 1.19 1.13 1.07

0.3

CFM 2720 2670 2620 2535 2450 2380 2310

2420 2170 2145 2120

RPM 978 952 926 908 889 868 847

896 871 850 828

kW 1.39 1.38 1.36 1.29 1.23 1.17

1.11

1.26 1.20 1.09 0.98

0.4

CFM 2560 2525 2490 2390 2290 2230

2460 2300

RPM 980 954 927 909 890 869

921 897

kW 1.32 1.31 1.30 1.24

1.19 1.12

1.15 1.14

0.5

CFM 2460 2355 2250 2236

2570 2460 2350

RPM 982 955 928 910

966 945 924

kW 1.25

1.22 1.21 1.21

1.33 1.26 1.19

0.6

CFM 2260

2670 2575 2488 2400 2300 2200

RPM 963

1026 1005 987 968 947 925

kW

1.23

1.52 1.46 1.33 1.21 1.11 1.01

0.7

CFM

2620 2530 2440 2335 2230 2120 2010

RPM

1048 1027 1006 988 969 948 926

kW

1.48 1.47 1.45 1.33 1.20 1.10 0.99

0.8

CFM

2510 2400 2290 2185 2080

RPM

1049 1028 1007 989 970

kW

1.42 1.36 1.29 1.20 1.11

0.9

CFM

2310 2225 2140

RPM

1051 1030 1008

kW

1.41 1.34 1.28

1.0

CFM

2210

RPM

1052

kW

1.40

LOW SPEED OPERATION - FOR REFERENCE ONLY

Low Static

0.1

CFM 1915 1828 1740 1715 1690 1619 1548 1486

RPM 657 639 620 585 550 556 561 547

kW 0.59 0.59 0.58 0.56 0.55 0.51 0.47 0.47

0.2

CFM 1680 1605 1530 1480 1430 1366 1302

RPM 658 640 621 589 556 559 562

kW 0.53 0.58 0.63 0.57 0.51 0.48 0.46

0.3

CFM 1440

RPM 659

kW 0.48

Medium Static

0.2

CFM

1920 1855 1790 1670 1550 1500 1450

RPM

647 632 616 599 582 566.5 551

kW

0.53 0.49 0.45 0.49 0.53 0.51 0.50

0.3

CFM

1910 1855 1800 1780 1760 1660 1560

RPM

701 687 672 660 648 633 617

kW

0.65 0.63 0.61 0.56 0.51 0.52 0.53

0.4

CFM

1705 1653 1600 1560 1520

RPM

703 689 675 663 650

kW

0.59 0.59 0.58 0.53 0.49

0.5

CFM

1510

RPM

705

kW

0.58

NOTES:

* Denotes Recommended Sheave Setting.

- Boldface type indicates factory recommended blower operating range.

- Values include losses for 2” standard air ﬁlters, unit casing, and dry evaporator coil.

- For 208V operation deduct approximately 0.5% from CFM shown.

- See Accessory Performance Data table for additional static pressure information.

FACTORY STANDARD DRIVE CONSISTS OF:

12” x 12” FC Blower, 2 HP / 2 Speed Motor

1VP40 Sheave, BK77 Pulley Belt & B57 Belt

MEDIUM STATIC DRIVE CONSISTS OF:

Same except uses 1VP44 Motor Sheave.

20

P7TQ-072C/D/N SERIES

2 HP, 2 SPEED, HORIZONTAL BLOWER DATA

Factory Standard & Medium Static Drive

HIGH SPEED OPERATION

EXTERNAL

UNIT STATIC

(IN WC)

OPERATING

@ 230V, 460V,

OR 575V

ADJUSTABLE MOTOR SHEAVE SETTING

FULLY

CLOSED

0.5

TURN

OPEN

1

TURN

OPEN

1.5

TURNS

OPEN

2

TURNS

OPEN

2.5

TURNS

OPEN

3

TURNS

OPEN

3.5

TURNS

OPEN

4

TURNS

OPEN

4.5

TURNS

OPEN*

5

TURNS

OPEN

0.1

CFM

RPM

kW

0.2

CFM

2800

RPM 740

kW

0.81

0.3

CFM 2700 2650 2600

RPM 765 754 742

kW 0.85 0.84 0.82

0.4

CFM 2735 2520 2460 2400

RPM 802 767 756 744

kW 0.88 0.86 0.85 0.83

0.5

CFM 2780 2525 2270 2205 2140

RPM 838 804 769 758 746

kW 0.90 0.89 0.87 0.86 0.84

0.6

CFM

2830

2685 2540 2255 1970 1880 1790

RPM 880 860 839 804.5 770 759 747

kW

0.89

0.90 0.91 0.89 0.87 0.86 0.85

0.7

CFM 2735 2600 2435 2270

RPM 904 882 862 841

kW 0.91 0.89 0.90 0.91

0.8

CFM

2805

2680 2505 2330 2140 1950

RPM 945 931 908 884 865 845

kW

0.90

0.92 0.91 0.90 0.90 0.90

0.9

CFM 2680 2545 2410 2220 2030

RPM 963 948 932 910 887

kW 0.87 0.91 0.94 0.93 0.91

1.0

CFM 2410 2265 2120

RPM 963 949 934

kW 0.87 0.91 0.95

LOW SPEED OPERATION (FOR REFERENCE ONLY)

0.1

CFM 2460 2405 2350 2278 2205 2133 2060 1955 1850 1825 1800

RPM 639 629 618 604 589 575 560 537 514 509 503

kW 0.70 0.74 0.78 0.77 0.76 0.75 0.74 0.73 0.71 0.73 0.75

0.2

CFM 2240 2200 2160 2070 1980 1890 1800 1675 1550 1500 1450

RPM 637 628 619 605 591 576 562 538 514 510 505

kW 0.71 0.74 0.78 0.77 0.76 0.75 0.75 0.73 0.72 0.74 0.76

0.3

CFM 2000 1940 1880 1775 1670 1565 1460 1318 1175

RPM 639 630 621 607 592 578 563 539 515

kW 0.72 0.74 0.76 0.76 0.76 0.75 0.75 0.74 0.73

0.4

CFM 1690 1610 1530

RPM 643 633 623

kW 0.72 0.74 0.77

NOTES:

- Boldface type indicates factory recommended blower operating range.

- Values include losses for 2” standard air ﬁlters, unit casing, and dry evaporator coil.

- For 208V operation deduct approximately 0.5% from CFM shown.

- See Accessory Performance Data table for additional static pressure information.

FACTORY DRIVE CONSISTS OF:

12” x 12” FC Blower, 2 HP / 2 Speed Motor

1VP40 Sheave, BK77 Pulley, and B57 Belt.

Table 6. P7TQ-072 C/D/N Series - Horizontal Models

La page charge ...

Mammoth P7TQ Guide d'installation

Mammoth P7TQ Guide d'installation

dans d''autres langues

Documents connexes

Autres documents