Maytag FRONT-LOADING AUTOMATIC WASHER W10254495A Mode d'emploi

Marque: Maytag

Modèle: FRONT-LOADING AUTOMATIC WASHER W10254495A

Catégorie: Machines à laver

Taper: Mode d'emploi

Ce manuel convient également à

W10254495B

W10254496B - SP

If you have any problems or questions, visit us at www.maytag.com

Pour tout problème ou question, consulter www.maytag.ca

Designed to use only HE

High Efciency detergents.

Conçue pour l’utilisation

d’un détergent haute

efcacité seulement.

Certied to Sanitize and to Reduce Allergens

Homologué pour assainir et pour réduire la présence

d’allergènes

Use & Care Guide

Guide d’utilisation et d’entretien

Para obtener acceso

al Manual de uso y cuidado

en español, o para obtener

información adicional acerca

de su producto, visite:

www.maytag.com

FRONT-LOADING AUTOMATIC WASHER

LAVEUSE AUTOMATIQUE À CHARGEMENT FRONTAL

WASHER SAFETY

TABLE OF CONTENTS

WASHER SAFETY ...................................................................2

ACCESSORIES ........................................................................3

CONTROL PANEL AND FEATURES ......................................4

USING THE DISPENSER ........................................................6

CYCLE STATUS LIGHTS .........................................................7

CYCLE GUIDE ......................................................................... 8

USING YOUR WASHER ........................................................10

WASHER MAINTENANCE ....................................................14

TROUBLESHOOTING ...........................................................17

WARRANTY ........................................................................... 24

ASSISTANCE OR SERVICE .................................. Back Cover

TABLE DES MATIÈRES

SÉCURITÉ DE LA LAVEUSE ................................................25

ACCESSOIRES ........................................................................3

TABLEAU DE COMMANDE ET CARACTÉRISTIQUES .......26

UTILISATION DU DISTRIBUTEUR ....................................... 29

TÉMOINS LUMINEUX DE PROGRAMME ...........................30

GUIDE DES PROGRAMMES ................................................31

UTILISATION DE LA LAVEUSE ............................................34

ENTRETIEN DE LA LAVEUSE ..............................................38

DÉPANNAGE .........................................................................42

GARANTIE .............................................................................51

ASSISTANCE OR SERVICE ...................... Couverture arrière

ACCESSORIES

Customize your new washer and dryer with the following

genuine Whirlpool accessories. For more information on options

and ordering, contact your dealer, or visit: www.maytag.com.

ACCESSOIRES

Personnalisez votre nouvelle laveuse et sécheuse grâce

aux authentiques accessoires Whirlpool suivants. Pour

plus d’informations sur les options et sur les possibilités

de commande, contactez votre revendeur ou consultez :

www.maytag.ca.

Stack Kit

If space is at a premium,

the stack kit allows the dryer

to be installed on top of

the washer.

Worksurface

The worksurface bridges the washer and

dryer, and provides a convenient working

and storage area.

15" Pedestal

Color-matched pedestals raise

the washer and dryer to a more

comfortable working height.

The large drawer provides

convenient storage.

Piédestal de 15"

Les piédestaux aux coloris assortis

surélèvent la laveuse et la sécheuse

pour les amener à une hauteur

d’utilisation plus confortable. Le

grand tiroir offre une capacité de

rangement pratique.

Surface de travail

La surface de travail établit la liaison entre

la laveuse et la sécheuse et offre une zone

de travail et d’entreposage pratique.

Ensemble de superposition

Si l’espace disponible est

restreint, l’ensemble de

superposition permet à la

sécheuse d’être installée par

dessus la laveuse.

power

cancel

start

pause

press and

hold to start

press and hold

for 3 seconds

steam for stains

press & hold for

drum light

fresh hold

whites

heavy duty

delicate

rinse/drain

& spin

small

load

with

clean

washer

bedding

wrinkle control

allergen

normal

soak

temp levelsoil level spin speed

extra

rinse

oxi

boost

max

extract

cycle

signal

control

lock

CONTROL PANEL AND FEATURES

Not all features and cycles are available on all models.

Steam models

Non-Steam models

POWER/CANCEL BUTTON

Press to turn the washer on and off.

Press to stop/cancel a cycle at any time.

WASH CYCLE KNOB

Turn the Wash Cycle Knob to select a cycle for your laundry

load. See “Cycle Guide” for detailed descriptions of cycles

that best suit your load.

START/PAUSE BUTTON

Press and hold to start a cycle, or press once while a cycle

is in process to pause it.

DELAY START + and - BUTTONS

Use these buttons to delay the start of the wash cycle

by up to 10 hours on models with Steam, and 8 hours

on non-Steam models.

A HE detergent

B Liquid fabric softener

C Liquid Chlorine bleach

D Oxi Boost

A HE detergent

B Liquid fabric softener

C Liquid chlorine bleach

power

cancel

start

pause

press and

hold to start

press and hold

for 3 seconds

whites

heavy duty

rinse/drain

& spin

small

load

with

clean

washer

wrinkle control

normal

soak

allergen

delicate

temp levelsoil level spin speed

extra

rinse

cycle

signal

control

lock

stain

clean

fresh

hold

LED DISPLAY AND SETTINGS BUTTONS

When you select a cycle, its default settings will light up and

the Estimated Time Remaining will be displayed. Factors

such as load size, wash temperature, and water pressure

may affect the time shown in the display. Tightly packing,

unbalanced loads, or excessive suds may cause the washer

to adjust the cycle time, as well.

Use the buttons along the bottom of the display to adjust

settings. See “Cycle Guide” for available settings on each

cycle. Not all settings are available with all cycles.

Temp Level

The recommended wash temperature is preset for each

cycle. You may also select a wash temperature based

on the type of fabric and soils being washed. For best

results, use the warmest wash water safe for your

fabric, following the garment label instructions. All wash

temperatures feature a cold rinse, except Warm*, which

has a warm wash and a warm rinse.

Soil Level

Soil level (wash time) is preset for each wash cycle. As you

press the Soil Level button, the cycle time will increase or

decrease in the Estimated Time Remaining display.

For most loads, use the soil level that is preset with the

cycle you have chosen. For heavily soiled and sturdy

fabrics, press Soil Level to select more wash time. For

lightly soiled and delicate fabrics, press Soil Level to

select less wash time. Lower soil level settings will help

reduce tangling and wrinkling.

Spin Speed

This washer automatically selects the spin speed based

on the cycle selected. Preset speeds can be changed.

• Faster spin speeds mean shorter dry times, but may

increase wrinkling in your load.

• Slower spin speeds reduce wrinkling, but will leave

your load more damp.

Cycle Status Lights

The indicator bar along the right side of the display will

let you know what stage of the wash cycle is in process,

as well as when the door is locked or if you can still add

an item. For more information on each stage, see “Cycle

Status Lights”.

OPTION BUTTONS

Use these buttons to activate additional wash options

or additional features on the washer. Not all options are

available on all models or all cycles. See the “Cycle Guide”

for information on which cycles include which options.

Extra Rinse

Activate this option to add an extra rinse to most cycles.

NOTE: Some cycles include this feature as a default. See

“Cycle Guide” for details.

Oxi Boost (on some models)

Turn this option on when using Oxi boost products in the

dispenser to ensure they are dispensed at the optimal

time in the cycle.

Max Extract™ (on some models)

Max Extract™ uses an extended high-speed spin to

remove additional water during the spin. This helps reduce

drying times.

Stain Clean (on some models)

The Stain Clean option adds additional soak and wash

time to many cycles to help remove tough stains.

An integrated heater helps to maintain optimal wash

temperatures.

Cycle Signal

Use this option to adjust volume of the signal that sounds

at end of cycle.

NOTE: You may also turn off the tones that sound when a

button is pressed. Press and hold the Cycle Signal button

for about one second to turn button sounds on or off.

Control Lock

Press and hold for 3 seconds to lock the controls to

avoid unwanted changes or operation. Press and

hold 3 seconds again to unlock. The indicator will light

to show when controls are locked. You may still press

START/PAUSE to pause the cycle, or press the POWER/

CANCEL button to turn the washer off.

DRUM LIGHT (Steam models only)

Steam models feature an LED drum light. Press and hold

Steam for Stains to turn the LED drum light on or off. The

light will also turn on when the door is open, and turn off

automatically after about 5 minutes.

STEAM FOR STAINS (Steam models only)

The Steam for Stains option adds additional soak and

wash time to many cycles to help remove tough stains.

An integrated heater helps to maintain optimal wash

temperatures. Steam for Stains includes a Steam boost for

added cleaning power. See the “Cycle Guide” for cycles that

allow the Steam for Stains option.

FRESH HOLD

OPTION

With the washer on, press to activate the Fresh Hold

option. This will periodically tumble the load after the end

of the cycle for up to 16 hours while the integrated fan

circulates air through the washer to reduce humidity. You

may also activate the Fresh Hold

option without running a

cycle by pressing and holding for 3 seconds, then pressing

START/PAUSE.

NOTES:

• The door will lock while the Fresh Hold

option is active.

Press the POWER/CANCEL button to stop the cycle and

unlock the door.

• Fresh Hold

is not available if the spin speed is set to

No Spin.

DISPENSER DRAWER

The dispenser drawer gives you the convenience of

automatically adding HE detergent, liquid chlorine bleach,

and liquid fabric softener to the wash load at the proper

time. Steam models also feature an Oxi /color-safe bleach

compartment. See “Using the Dispenser” for information on

using the dispenser drawer.

High Efciency “HE” detergent compartment

This compartment holds liquid or powdered HE

detergent for your main wash cycle.

For models without an Oxi dispenser compartment,

liquid or powdered color-safe bleach or Oxi

booster product may be added to the HE detergent

compartment along with the same type of detergent,

liquid or powdered.

Liquid fabric softener compartment

Automatically dilutes and dispenses liquid fabric

softener at the optimal time in the cycle.

NOTE:

Use only liquid fabric softener in this dispenser.

Liquid chlorine bleach compartment

Automatically dilutes and dispenses liquid chlorine

bleach at the optimal time during the rst rinse after the

wash cycle. This compartment cannot dilute powdered

bleach.

Oxi Boost compartment (Steam models only)

This compartment holds measured liquid or powdered

Oxi booster product and dispenses it at the proper time

in the cycle. See the “Cycle Guide” for cycles that offer

the Oxi Boost option.

USING THE DISPENSER

Pour a measured amount of HE

detergent into detergent compartment.

For powdered detergent, slide the

selector to the left. For liquid detergent,

slide the selector to the right.

Do not overll; adding too much

detergent may cause detergent to be

dispensed into the washer too early.

Use only High Efciency

(HE) detergent.

Powdered detergent:

Slide the selector to the left.

Liquid detergent:

Slide the selector to the right.

Pour a measured amount of HE

detergent into detergent compartment.

For powdered detergent, slide the

selector to the left. For liquid detergent,

slide the selector to the right.

Do not overll; adding too much

detergent may cause detergent to be

dispensed into the washer too early.

Use only High Efciency

(HE) detergent.

Powdered detergent:

Slide the selector to the left.

Liquid detergent:

Slide the selector to the right.

Models with a 4-compartment dispenser

Models with a 3-compartment dispenser

If you would like to use powdered or liquid oxi-type

boosters or color-safe bleach, follow the manufacturer’s

recommendations for placement. If no recommendation

is available, you may add powdered or liquid oxi-type

boosters or color-safe bleach to the detergent

compartment with the same type of detergent,

powdered or liquid.

IMPORTANT:

Do not add single-dose laundry packet to dispenser

drawer.

Use powdered detergent when using the Delay Wash

option. Liquid detergent may seep out before the

wash begins.

HE detergent

compartment

HE detergent

compartment

To use the dispenser drawer:

1. Open the dispenser drawer.

2. Add laundry products as described in steps 4–6.

3. Slowly close the dispenser drawer. Make sure it is

completely closed.

NOTE: A small amount of water may remain in the dispensers

from the previous wash cycle. This is normal.

IMPORTANT:

Do not add single-dose laundry packet to dispenser

drawer.

Use powdered detergent when using the Delay Wash

option. Liquid detergent may seep out before the wash

begins.

CYCLE STATUS LIGHTS

The Cycle Status Lights show the progress of a cycle. At each

stage of the process, you may notice sounds or pauses that are

different from traditional washers.

Door Locked

Door Locked will light to indicate that the door is locked and

cannot be opened without rst pausing or canceling the cycle.

Sensing

When the START/PAUSE button is pressed, the washer will

rst perform a self-test on the door lock mechanism. You will

hear a click, the drum will make a partial turn, and the door

will unlock briey before locking again.

Once the door has locked the second time, the washer will

begin tumbling and adding water. This sensing process will

continue until the correct amount of water has been added

for the load. You may also hear water owing through the

dispenser, adding detergent to the load.

The displayed time may change as the washer goes through

the sensing process. This is normal.

Add a Garment

When Add a Garment is lit, you may pause the washer, open

the door, and add items.

Sanitized

Sanitized will light on cycles with a Sanitize setting once the

load has been washed at the proper temperature for the

necessary time to meet NSF Sanitization requirements.

Delay

The Delay indicator will light if a Delay Start has been set.

Once the programmed delay has ended, the indicator will

turn off and the cycle will begin.

Wash

This is the main portion of the wash cycle. You will see the

washer tumble the load. The motor sounds may change at

different stages in the cycle. The wash time is determined by

the selected cycle and soil level along with your load size.

Rinse

You will hear sounds similar to the wash cycle as the

washer rinses and moves the load. If used, liquid chlorine

bleach is added in the rst rinse. Fabric Softener is added

in the last rinse.

Spin

The washer spins the load at increasing speeds for

proper water removal, based on the selected cycle

and spin speed.

Steam (on some models)

This will light to show that the cycle is using a Steam boost

for added cleaning power.

Done

Once the cycle is complete, this light will come on.

Remove the load promptly for best results.

Fresh Hold

The Fresh Hold

indicator will light when the Fresh

Hold

option is active. During this time, the washer

will occasionally tumble the load while a fan circulates

fresh air through the washer.

Steam model shown

temp level soil levelspin speed

CYCLE GUIDE — STANDARD CYCLES

Normally soiled cottons, Normal Hot High Extra Heavy Extra Rinse This cycle combines medium-speed

linens, sheets, and Warm/Cold* Medium Heavy Stain Clean

tumbling and a high-speed spin.

mixed garment loads Warm/Warm No Spin Normal Max Extract™ This cycle is designed to provide

Cold Light Oxi Boost the most energy efciency.

Fresh Hold

Delay Start

Sturdy colorfast Heavy Sanitize

†

High Extra Heavy Extra Rinse High-speed tumbling and a

fabrics and heavily Duty Hot Medium Heavy Stain Clean

high-speed nal spin help

soiled garments, Warm/Cold* Low Normal Max Extract™ provide optimal cleaning and

towels, and jeans Warm/Warm No Spin Light Oxi Boost reduce drying times.

Cold Fresh Hold

Delay Start

Heavily soiled white Whites Sanitize

†

High Extra Heavy Extra Rinse Hot wash temperatures ensure

fabrics and garments Hot Medium Heavy Stain Clean

liquid chlorine bleach action.

Warm/Cold* Low Normal Max Extract™ An Extra Rinse helps remove

Warm/Warm No Spin Light Oxi Boost any bleach residue in clothes.

Cold Fresh Hold

Delay Start

Heavily soiled Power Wash Sanitize

†

High Extra Heavy Extra Rinse Features an extended wash time

durable fabrics, Hot Medium Heavy Stain Clean

to help remove tough stains.

overalls, coveralls, Warm/Cold* Low Normal Max Extract™ Stain Clean/Steam for Stains

sweatshirts, pants, and Warm/Warm No Spin Light Oxi Boost (depending on model) is

outdoor garments Cold Fresh Hold

automatically added for extra

Delay Start cleaning power.

Lightly-soiled shirts, Wrinkle Hot Medium Extra Heavy Extra Rinse This cycle combines low-speed

blouses, trousers, Control Warm/Warm Low Heavy Stain Clean

tumbling and low-speed spin

pants and dresses Cold Extra Low Normal Max Extract™ for gentle fabric care and reduced

No Spin Light Oxi Boost wrinkling

Fresh Hold

Delay Start

Blankets, comforters Bedding Sanitize

†

High Extra Heavy Extra Rinse Uses an initial soak to completely

Hot Medium Heavy Stain Clean

saturate the load, followed by

Warm/Cold* Low Normal Oxi Boost medium wash speeds and a

Warm/Warm Extra Low Light Fresh Hold

medium-speed spin to maintain

Cold No Spin Delay Start load balance.

Sturdy garments and Allergen

††

Sanitize

†

High Extra Heavy Extra Rinse Uses more water to ush out

household items Hot Medium Heavy Stain Clean

allergens such as dust mites

exposed to possible Normal Max Extract™ and pet dander from

allergens Light Oxi Boost normally-soiled items.

Fresh Hold

Delay Start

Sheer fabrics, Delicate Warm/Cold* High Normal Extra Rinse This cycle combines low-speed

lingerie, sweaters, Warm/Warm Medium Light Fresh Hold

tumbling and low-speed spin

and silks Cold Low Delay Start for gentle fabric care and reduced

Extra Low wrinkling.

No Spin

Items to wash

using default

cycle settings:

Cycle:

Wash

Temperature*:

Spin

Speed:

Soil

Level:

Available

Options:

Cycle Details:

†† Allergen

Allergen cycle certied by NSF International, an independent, third party testing and certication organization.

The certication veried that this cycle reduced tested allergens by at least 95.0% and maintained the water

temperature necessary to kill dust mites. Only the allergen cycle has been designed to meet the requirements of

NSF Protocol P351 for Allergen Reduction Performance effectiveness.

† Sanitize

Cycles certied by NSF International, an independent, third party testing and certication organization are those with the

sanitize temperature selection available. The certication veried that these cycles reduce 99.9% of bacteria typically

found on clothing, bedding, and towels. There is no carryover of bacteria between loads after the cycle is complete.

Only cycles with sanitize wash temperature selected have been designed to meet the requirements of NSF Protocol

P172 for Sanitizing Effectiveness.

Settings and options shown in bold are default settings for that cycle. For best fabric care, choose the cycle that best ts the

load being washed.

Not all cycles and options are available on all models.

For best performance, not all settings are available with each cycle, and some options cannot be used together.

* All temperature selections feature a Cold rinse, except Warm/Warm, which features a warm wash and a warm rinse.

Stain Clean on non-Steam models. Steam for Stains on Steam models. See “Control Panel and Features” for additional information.

Models: MHW6000**, MHW7000**

Small loads of 3 - 4 Small Load Hot High Heavy Extra Rinse For small loads (3-4 items) needed

lightly soiled garments Warm/Warm Medium Normal Fresh Hold

quickly. This cycle combines

Cold Low Light Delay Start high-speed tumbling, a shortened

Extra Low wash time, and a high-speed spin

for reduced drying times.

Swimwear, items Rinse/Drain Warm/Cold* High N/A Extra Rinse This cycle adds water, then uses

that need rinsing only & Spin Warm/Warm Medium Max Extract™ high-speed tumbling and an extra

Cold Low Fresh Hold

high-speed spin. For some fabrics,

Extra Low Delay Start you may wish to set the spin speed

No Spin to a lower setting.

Wet load of clothes Rinse/Drain N/A High N/A Max Extract™ Use Drain & Spin to remove excess

& Spin Medium Fresh Hold

water from the load by choosing

Low Delay Start Rinse/Drain & Spin and turning off

Extra Low Extra Rinse. Spin speed can be set

No Spin to a lower setting.

Heavily soiled garments Soak Warm/Cold* Extra Heavy Fresh Hold

Provides an extended soak without

Warm/Warm Heavy Delay Start a nal spin to help loosen tough

Cold Normal stains prior to a wash cycle.

Light

No clothes in washer Clean Washer Use this cycle every 30 washes to

with affresh

keep the inside of your washer fresh

and clean. This cycle uses a higher

water level. Use with affresh

Washer Cleaner tablet or liquid

chlorine bleach to thoroughly clean

the inside of your washer. This cycle

should not be interrupted. See

“Washer Care.”

IMPORTANT: Do not place

garments or other items in the

washer during the Clean Washer

with affresh

cycle. Use this cycle

with an empty wash tub.

CYCLE GUIDE — SPECIAL-PURPOSE CYCLES

Cycle:

Wash

Temperature*:

Spin

Speed:

Soil

Level:

Available

Options:

Cycle Details:

Load Size Recommendations

For best results, follow the load size recommendations noted for each cycle.

Small load: Fill the washer drum with 3-4 items, not more than 1/4 full.

Medium load: Fill the washer drum up to about 1/2 full.

Large load: Fill the washer drum up to about 3/4 full.

Extra-large load: Fill the washer drum, but make sure clothes can tumble freely.

For best results, avoid packing tightly.

* All temperature selections feature a Cold rinse, except Warm/Warm, which features a warm wash and a warm rinse.

Settings and options shown in bold are default settings for that cycle. For best fabric care, choose the cycle that best ts the

load being washed.

Not all cycles and options are available on all models.

For best performance, not all settings are available with each cycle, and some options cannot be used together.

Items to wash

using default

cycle settings:

USING YOUR WASHER

Sort items by recommended cycle, water temperature, and

colorfastness. Separate heavily soiled items from lightly soiled.

Separate delicate items from sturdy fabrics. Treat stains

promptly and check for colorfastness by testing stain remover

products on an inside seam.

1. Sort and prepare your laundry

First wash cycle without laundry

Before washing clothes for the rst time, if not completed during

the nal installation step, choose the QUICK WASH cycle and

run it without clothes. Use only HE detergent. Use 1/2 the

manufacturer’s recommended amount for a medium-size load.

This initial cycle serves to ensure the interior is clean before

washing clothes.

Choosing the Right Detergent

Use only High Efciency detergents. The package will be

marked “HE” or “High Efciency.” Low-water washing creates

excessive sudsing with a regular non-HE detergent. Using regular

detergent will likely result in longer cycle times and reduced

rinsing performance. It may also result in component failure and,

over time, build-up of mold or mildew. HE detergents are made

to produce the right amount of suds for the best performance.

Follow the manufacturer’s instructions to determine the amount

of detergent to use.

Use only High Efciency (HE) detergent.

IMPORTANT:

n Empty pockets. Loose change, buttons, or any small object

can plug pumps and may require a service call.

n Close zippers, fasten hooks, tie strings and sashes, and

remove non-washable trim and ornaments.

n Mend rips and tears to avoid further damage to items

during washing.

n Turn knits inside out to prevent pilling. Separate lint-takers

from lint-givers. Synthetics, knits, and corduroy fabrics will

pick up lint from towels, rugs, and chenille fabrics.

n Do not dry garments if stains remain after washing, because

heat can set stains into fabric.

n Always read and follow fabric care labels and laundry

product instructions. Improper usage may cause damage

to your garments.

2. Add single-dose laundry packet, Oxi,

or color-safe bleach (if desired)

Single-dose laundry packet, Oxi-type boosters, or color-safe

bleach can be added to the drum prior to adding laundry.

(Some models Oxi and bleach can be added to dispenser

drawer).

Add a measured amount of liquid chlorine bleach to the

bleach compartment. Do not overll, dilute, or use more than

2/3 cup (165 mL). Use a measuring cup with a pour spout; do

not guess.

Do not ll beyond the “MAX” level. Overlling will cause

bleach to dispense too soon and may cause garment

damage.

Do not add single-dose laundry packet, oxi-product, or

color-safe bleach to this dispenser. It will not dispense

correctly. See “Using the Dispenser” instructions on how

to use the dispenser.

6. Add liquid chlorine bleach

to dispenser (if desired)

Pour a measured amount of liquid fabric softener into liquid

fabric softener compartment. Always follow manufacturer’s

directions for correct amount of fabric softener based on your

load size.

Fabric softener is always dispensed in the last rinse, even if

Extra Rinse is selected.

IMPORTANT: Do not overll, dilute, or use more than 1/4 cup

(60 mL) of fabric softener. Do not ll past the MAX line.

Overlling dispenser will cause fabric softener to immediately

dispense into washer.

Do not spill or drip any fabric softener onto the clothes.

Do not use liquid fabric softener dispenser balls in this

washer. They will not dispense correctly.

5. Add fabric softener to dispenser

(if desired)

Liquid fabric

softener

compartment

4-compartment dispenser shown

Liquid chlorine

bleach

compartment

4-compartment dispenser shown

Open the washer door. Place a load of sorted clothes loosely in

the washer. Items need to move freely for best cleaning and to

reduce wrinkling and tangling. Close the washer door by pushing

it rmly until the latch clicks.

n Depending on load type and cycle, the washer can be fully

loaded, but not tightly packed. Washer door should close

easily. See “Cycle Guide” for loading suggestions.

n Mix large and small items and avoid washing single items.

Load evenly.

n Wash small items in mesh garment bags. For multiple items,

use more than one bag and ll bags equally.

3. Load laundry into washer

Select detergent dispenser, based on type of HE detergnet

used (liquid or powdered). See “Using the Dispenser”

instructions on how to use the dispenser.

4. Add HE detergent

3-compartment dispenser

4-compartment dispenser

power

cancel

8. Press POWER/CANCEL to turn

on washer

Slowly close the dispenser drawer. Make sure the drawer is

closed completely, then press and hold POWER/CANCEL to

turn on the washer.

whites

heavy duty

delicate

rinse/drain

& spin

small

load

with

clean

washer

bedding

wrinkle control

allergen

normal

soak

9. Select CYCLE

The display will show the default settings for the selected

cycle. If desired, press the button beneath each setting to

adjust the Temp Level, Soil Level, and Spin Speed. Adjusting

the Soil Level will change the Estimated Time Remaining.

Tightly packing, unbalanced loads, or excessive suds may also

cause the washer to increase the cycle time.

NOTE: Not all settings are available on all cycles. See “Cycle

Guide” for available settings.

Turn cycle knob to select your wash cycle. See “Cycle Guide”

for details on cycle features. Not all options and settings are

available on all cycles.

press and hold

for 3 seconds

temp level soil levelspin speed

extra

rinse

oxi

boost

max

extract

cycle

signal

control

lock

10. Adjust settings, if desired

Steam model shown

press and hold

for 3 seconds

steam for stains

press & hold for

drum light

fresh hold

extra

rinse

oxi

boost

max

extract

cycle

signal

control

lock

11. Select any additional options

To add additional options to the cycle, such as Extra Rinse,

Fresh Hold

, Stain Clean/Steam for Stains (on some models),

or Max Extract™ (on some models), press the button for the

desired options to add them to the selected cycle.

NOTE: Not all options are available with all cycles. See “Cycle

Guide” for available options.

Steam model shown

On models with a 4-compartment dispenser,

add Oxi booster or Color-Safe Bleach to the

Oxi compartment. Be sure to select the

Oxi Boost option.

Always follow the manufacturer’s recommendations.

For models without an Oxi compartment:

If you would like to use powdered or liquid oxi-type boosters or

color-safe bleach, follow the manufacturer’s recommendations

for placement. If no recommendation is available, you may add

powdered or liquid oxi-type boosters or color-safe bleach to

the detergent compartment with the same type of detergent,

powdered or liquid.

7. Add Oxi or Color-Safe Bleach

(on some models)

Oxi/Color-Safe Bleach

compartment

4-compartment dispenser shown

oxi

boost

12. Setting a delayed start

If you do not want to begin a cycle immediately, you may

choose the DELAY START option. This will delay the start

of the wash cycle by up to 10 hours on models with Steam,

and 8 hours on non-Steam models.

To set a delayed Start:

1. Press DELAY START s and t buttons to set the desired

delay time.

2. Press START/PAUSE to set the delay. The delay countdown

has started when the START/PAUSE light stops blinking.

temp level soil le

vel

start

pause

press and

hold to start

13. Press and hold START/PAUSE

to begin wash cycle

Press and hold the START/PAUSE button to start the wash

cycle. To pause a cycle in progress, press the START/PAUSE

button once, then press and hold again to continue the cycle.

To cancel a cycle, press the POWER/CANCEL button.

Once you press and hold START/PAUSE, you will hear the

door lock, unlock, and lock again. The washer door will remain

locked during the wash cycle.

Unlocking the door to add garments:

If you need to open the door to add 1 or 2 missed garments,

you may do so while the “Add a Garment” light is lit.

Press START/PAUSE once; the door will unlock

once the washer movement has stopped.

This may take several minutes. Then close

door and press START/PAUSE again to restart

the cycle.

start

pause

press and

hold to start

14. Remove garments promptly

after cycle is nished

Promptly remove garments after cycle has

completed to avoid odor and rusting of

metal objects on garments. When unloading

garments, pull back the door seal and check

for small items between the tub and the

washer drum.

If you will be unable to remove the load

promptly, use the Fresh Hold

option. If the

Fresh Hold

option is selected, the washer will

automatically activate the fan and tumble

the load periodically for up to 16 hours.

NOTE:

After any wash cycle is completed,

the door must be opened and then

closed before a new cycle can begin.

A small amount of water may remain in the dispensers after

the wash cycle is complete. This is normal.

This washer has a tight seal to avoid water leaks. To avoid

odors, leave the door open to allow the washer to dry

between uses.

fresh

hold

WASHER MAINTENANCE

Replace inlet hoses after 5 years of use to reduce the risk

of hose failure. Periodically inspect and replace inlet hoses

if bulges, kinks, cuts, wear, or leaks are found.

When replacing your inlet hoses, mark the date of

replacement on the label with a permanent marker.

NOTE: This washer does not include inlet hoses. See the

“Installation Instructions” for more information.

WATER INLET HOSES

WASHER CARE

Recommendations to Help Keep Your Washer Clean

and Performing at its Best

1. Always use High Efciency (HE) detergents and follow the

HE detergent manufacturer’s instructions regarding the

amount of HE detergent to use. Never use more than the

recommended amount because that may increase the

rate at which detergent and soil residue accumulate inside

your washer, which in turn may result in undesirable odor.

2. Use warm or hot water washes sometimes (not exclusively

cold water washes), because they do a better job of

controlling the rate at which soils and detergent accumulate.

3. Always leave the washer door slightly ajar between uses

to help dry out the washer and prevent the buildup of

odor-causing residue.

Cleaning Your Front Loading Washer

Read these instructions completely before beginning the

routine cleaning processes recommended below. This

Washer Maintenance Procedure should be performed,

at a minimum, once per month or every 30 wash cycles,

whichever occurs sooner, to control the rate at which soils

and detergent may otherwise accumulate in your washer.

Cleaning the Door Seal

1. Open the washer door and remove any clothing or items

from the washer.

2. Inspect the seal between the door opening and the drum

for stained areas or soil buildup. Pull back the seal to

inspect all areas under the seal and to check for foreign

objects.

3. If stained areas or soil buildup are found, wipe down

these areas of the seal using either of the following

two procedures:

a. affresh

Grit Grabber™ Cloth Procedure:

i. When the cycle is complete, gently pull back the

rubber door seal and clean the entire surface with

the rough side of the Grit Grabber™ cloth.

b. Dilute Liquid Chlorine Bleach Procedure:

i. Mix a dilute bleach solution, using 3/4 cup (177 mL)

of liquid chlorine bleach and 1 gallon (3.8 L) of warm

tap water.

ii. Wipe the seal area with the dilute solution, using

a damp cloth.

iii. Let stand 5 minutes.

iv. Wipe down area thoroughly with a dry cloth and let

washer interior air dry with door open.

IMPORTANT:

n Wear rubber gloves when cleaning with bleach.

n Refer to the bleach manufacturer’s instructions

for proper use.

WASHER CARE (cont.)

Cleaning the Inside of the Washer

This washer has a special cycle that uses higher water

volumes in combination with affresh

Washer Cleaner or

liquid chlorine bleach to thoroughly clean the inside of the

washer. Steam washer models also utilize steam to enhance

cleaning in this special cycle.

NOTE: Read these instructions completely before beginning

the cleaning process.

Begin procedure

1. affresh

Washer Cleaner Cycle Procedure

(Recommended):

a. Open the washer door and remove any clothing

or items.

b. Add an affresh

Washer Cleaner tablet to the washer

drum.

c. Do not add the affresh

Washer Cleaner tablet

to the dispenser drawer.

d. Do not add any detergent or other chemical to the

washer when following this procedure.

e. Close the washer door.

f. Select the CLEAN WASHER cycle.

g. Press the START button to begin the cycle. The Clean

Washer Cycle Operation is described below.

2. Chlorine Bleach Procedure:

a. Open the washer door and remove any clothing

or items.

b. Open the dispenser drawer and add 2/3 cup (160 mL)

of liquid chlorine bleach to the bleach compartment.

NOTE: Use of more liquid chlorine bleach than is

recommended above could cause product damage

over time.

c. Close the washer door and the dispenser drawer.

d. Do not add any detergent or other chemical to the

washer when following this procedure.

e. Close the washer door.

f. Select the CLEAN WASHER cycle.

g. Press the START button to begin the cycle. The Clean

Washer Cycle Operation is described below.

Description of Clean Washer Cycle Operation:

1. The Clean Washer cycle will determine whether clothing

or other items are in the washer.

2. If no items are detected in the washer, it will proceed

to step 3.

a. If any items are detected in the washer, “rL” (remove

load) will be displayed, and the washer “Controls Lock”

lights will remain lit. The door will unlock. Open washer

and remove any garments from the washer drum.

b. Press PAUSE/CANCEL or POWER/CANCEL

to clear the “rL” code.

c. Press START to restart the cycle.

3. After the cycle is complete, leave the door open slightly to

allow for better ventilation and drying of the washer interior.

WASHER CARE (cont.)

Cancellation of Clean Washer Cycle Operation:

If the Clean Washer cycle is canceled by the user after it has

been initiated, it may take up to 30 minutes for the washer

to purge any affresh

Cleaner, chlorine bleach, or other

chemistry from the wash system and to adequately rinse any

remaining chemistry. The washer door will remain locked until

the cancellation process has been completed. This assures

no cleaning chemistry will be carried over to the next wash

cycle and reduces the potential for damage to subsequent

loads of laundry or to the machine itself.

Clean Washer Cycle Cancellation Procedure:

1. Press the PAUSE/CANCEL or the POWER/CANCEL

button on the washer two times.

2. Washer will begin to drain and rinse away the remaining

cleaning chemistry.

3. The cycle will complete the cancellation process in

approximately 30 minutes or less.

4. The washer then can be used to either repeat the Clean

Washer cycle or to wash laundry using one of the regular

wash cycles selected by the user.

Cleaning the Outside of the Washer

Use a soft, damp cloth or sponge to wipe up any spills.

Occasionally wipe the outside of your washer to help

keep it looking new. Use mild soap and water.

IMPORTANT: To avoid damaging the washer’s nish, do not

use abrasive products.

CLEANING THE DISPENSER

You may nd laundry product residue leftover in your

dispenser compartments. To remove residue, follow this

recommended cleaning procedure:

1. Pull dispenser drawer out until it stops.

2. Press down on the release tab and pull straight out to

remove the dispenser.

CLEANING THE DISPENSER (cont.)

3. Lift off cover panel by

pulling straight up.

4. Wash dispenser and

cover panel in warm,

soapy water, using a mild

detergent.

5. Rinse with warm water.

6. Air dry or wipe with a

clean towel, slide cover

panel back onto posts on

dispenser.

7. Align edges of dispenser

with guides in washer,

then slide dispenser

back into slot.

IMPORTANT: Dispenser is

not dishwasher safe.

Operate your washer only when you are home. If moving,

or not using your washer for a period of time, follow these

steps:

1. Unplug or disconnect power to washer.

2. Turn off water supply to washer to avoid ooding due

to water pressure surges.

NON-USE AND VACATION CARE

WINTER STORAGE CARE

IMPORTANT: To avoid damage, install and store washer

where it will not freeze. Because some water may stay in

hoses, freezing can damage washer. If storing or moving

during freezing weather, winterize your washer.

To winterize washer:

1. Shut off both water faucets, disconnect and drain water

inlet hoses.

2. Put 1 qt. (1 L) of R.V.-type antifreeze in washer drum

and run washer on RINSE AND SPIN cycle for about

1 minute to mix antifreeze and remaining water.

3. Unplug washer or disconnect power.

IMPORTANT: To reduce risk of hose failure, replace inlet

hoses every ve years and periodically inspect for kinks,

cuts, wear or water leaks.

HELPFUL TIP: When replacing your inlet hoses, mark

replacement date on label with a permanent marker.

TRANSPORTING YOUR WASHER

1. Shut off both water faucets. Disconnect and drain water

inlet hoses.

2. If washer will be moved during freezing weather, follow

WINTER STORAGE CARE directions before moving.

3. Disconnect drain hose from drain system and from back

of washer.

4. Unplug power cord.

5. Place inlet hoses and drain hose inside washer drum.

6. Bundle power cord with a rubber band or cable tie to

keep it from hanging onto the ground.

IMPORTANT: Call for service to install new transport bolts.

Do not reuse transport bolts. Washer must be transported

in the upright position. To avoid structural damage to your

washer, it must be properly set up for relocation

by a certied technician.

REINSTALLING/USING WASHER AGAIN

To reinstall washer after non-use, vacation, winter storage,

or moving:

1. Refer to Installation Instructions to locate, level, and

connect washer.

2. Before using again, run washer through the following

recommended procedure:

To use washer again:

1. Flush water pipes and hoses. Reconnect water inlet

hoses. Turn on both water faucets.

2. Plug in washer or reconnect power.

3. Run washer through POWER WASH cycle to clean

washer and remove antifreeze, if used. Use only HE

detergent. Use half the manufacturer’s recommended

amount for a medium-size load.

If you experience

Possible Causes

Solution

First try the solutions suggested here or visit our website at www.maytag.com/help

for assistance and to possibly avoid a service call.

Error Code Appears in Display

Sud (Excess suds)

appears in display

Excessive suds in washer. Washer is

running a suds reduction routine.

Allow the machine to continue. Use only HE detergent.

Always measure detergent, and base detergent quantity on

load size. Follow detergent manufacturer’s instructions.

Press POWER/CANCEL once to clear the code. Then press

POWER/CANCEL again to restart washer. If code appears

again, call for service.

F8E1 (water supply

error) appears in display

Check for proper water supply.

Both hoses must be attached and have water owing to the

inlet valve.

Both hot and cold water faucets must be on.

Inlet valve screens on washer may be clogged.

Remove any kinks in the inlet hose.

F9E1 (drain pump

system error) appears

in display

Check plumbing for correct drain

hose installation. Drain hose extends

into standpipe farther than 4

⁄

”

(114 mm).

Check drain hose for proper installation.

Make sure the drain hose is not kinked, pinched, or blocked.

Remove any clogs from drain hose.

Use drain hose form and securely attach to drainpipe or tub.

Lower drain hose if the end is higher than 96" (2.4 m) above

the oor.

F5E2 (door will not lock)

appears in display

Washer door not locking.

Press POWER/CANCEL to cancel the cycle. Make sure the

door is closed completely and latching. Check for items in

the washer drum that may be keeping the door from closing

completely.

Washer beeps when

START/PAUSE is

pressed.

Door not closed.

Close the door completely.

F7E1 (motor drive error)

appears in display

Motor is having difculty turning

the drum.

Washer is tightly packed. Remove some items. See “Cycle

Guide” for load size recommendations.

Make sure that all shipping materials have been removed. See

the Installation Instructions.

“rL” (remove load)

appears in display

Load detected in drum during Clean

Washer with affresh

cycle.

Remove items from drum and restart Clean Washer

with affresh

cycle.

Washer making error

beeps.

Door has not been opened and closed

for at least 3 cycles.

This code may appear when the washer is rst turned on.

Open and close the door to clear the display.

Once any possible issues are corrected, press POWER/CANCEL once to clear the code. Reselect and restart the cycle.

F#E# code other than

as described above

appears in display

System error code.

Press POWER/CANCEL once to clear the code. Then press

POWER/CANCEL again to restart washer. If code appears

again, call for service.

Not using HE detergent or using too

much HE detergent.

Use only HE detergent. Always measure detergent and follow

manufacture’s directions based on load size and soil level.

TROUBLESHOOTING

First try the solutions suggested here or visit our website at www.maytag.com/help

for assistance and to possibly avoid a service call.

If you experience

Possible Causes

Solution

Feet may not be in contact with the

oor and locked.

Front and rear feet must be in rm contact with oor, and washer

must be level to operate properly. Jam nuts must be tight

against the bottom of the cabinet.

Check oor for exing or sagging. If ooring is uneven, a 3/4"

(19 mm) piece of plywood under your washer will reduce sound.

See “Level the Washer” in Installation Instructions.

Load could be unbalanced

or too large.

Avoid tightly packing the load. Avoid washing single items.

Balance a single item such as a rug or jeans jacket with a

few extra items.

Use Bedding cycle for oversized, non-absorbent items

such as comforters or poly-lled jackets. Other items are

not appropriate for Bedding cycle. See “Cycle Guide”.

Item or load not suitable for selected cycle. See “Cycle Guide”

and “Using Your Washer” in this Use and Care Guide.

Empty pockets before washing. Loose items such as coins

could fall between washer drum and tub or may block pump.

It may be necessary to call for service to remove items.

Fill hoses not attached tightly.

Tighten ll-hose connection.

Are all four ll hose at washers properly seated?

Drain hose connection.

Check that the drain hose is properly secured to drainpipe or

laundry tub.

Check household plumbing for leaks

or clogged sink or drain.

Water can backup out of a clogged sink or drainpipe. Check

all household plumbing for leaks (laundry tubs, drain pipe,

water pipes, and faucets.)

Fill hose washers.

Noises

It is normal to hear metal items on clothing such as metal snaps,

buckles, or zippers touch against the stainless steel drum.

Objects caught in washer

drain system.

Clicking or metallic

noises

Gurgling or humming

It is normal to hear the pump making a humming sound with

periodic gurgling or surging as nal amounts of water are removed

during the spin/drain cycles.

Washer may be

draining water.

Water Leaks

Check the following for

proper installation:

Vibration, rocking, or

“walking”

Load not completely

covered in water.

Water level not visible on door or

does not cover clothes.

This is normal for an HE front load washer. The washer senses load

sizes and adds the correct amount of water for optimal cleaning.

Washer not performing as expected

Washer may not be level.

Vibration or Off-Balance

The door will lock unlock and lock again. You will hear three

clicks after pushing start. This is normal.

Door locking or unlocking.

Not using HE detergent or using too

much HE detergent.

Only use HE detergent. Suds from regular detergents can

cause leaking from the door or rear of cabinet. Always measure

detergent and follow manufacturer’s directions based on your

load requirements.

Water or suds leaking

from door or rear of

cabinet

Residue on door glass.

Periodically clean the the underside of the glass window to

avoid potential leaks.

The shipping bolts are still in the

back of the washer.

See “Remove transport bolts from washer” in the

Installation Instructions.

Door opened during “Add A

Garment.”

Water can drip off the inside of the door when the door is

opened after the start of a cycle.

TROUBLESHOOTING

Normal washer operation.

Door must be completely closed and latched for washer to run.

Washer will pause during certain phases of cycle.

Do not interrupt cycle.

The washer pauses for about 2 minutes during certain cycles.

Allow the cycle to continue. Some cycles feature periods of

tumbling and soak.

Washer may be stopped to reduce suds.

Plug power cord into a grounded 3 prong outlet.

Do not use an extension cord.

Ensure there is power to outlet.

Check electrical source or call an electrician to check if voltage

is low.

Reset a tripped circuit breaker. Replace any blown fuses.

NOTE: If problems continue, contact an electrician.

Washer not loaded as recommended.

Remove several items, rearrange load evenly in drum.

Close door and press START/PAUSE.

Do not add more than 1 or 2 additional items after cycle has

started to avoid tightly packing or unbalancing.

Not using HE detergent or using too

much HE detergent.

Only use HE detergent. Suds from regular detergents can slow

or stop the washer. Always measure detergent and following

manufacturers directions based on your load requirements.

To remove suds, cancel cycle. Select RINSE/DRAIN & SPIN.

Press START/PAUSE. Do not add more detergent.

After any wash cycle is completed, the door must be opened

and then closed before a new cycle can begin.

Do not add more water to the washer.

Door not opened between cycles.

If you experience

Possible Causes

Solution

Washer won’t run or ll,

washer stops working

Check for proper water supply.

Both hoses must be attached and have water owing to

inlet valve.

Both Hot and Cold water faucets must be turned on.

Check that inlet valve screens have not become clogged.

Check for any kinks in inlet hoses, which can restrict water ow.

Check proper electrical supply.

First try the solutions suggested here or visit our website at www.maytag.com/help

for assistance and to possibly avoid a service call.

Washer not performing as expected (cont.)

The washer door is not rmly shut. The door must be closed during operation.

TROUBLESHOOTING

Washer not performing as expected (cont.)

If you experience

Possible causes

Solution

Incorrect or wrong

wash or rinse

temperatures

Check for proper water supply.

Make sure hot and cold inlet hoses are not reversed.

Both hoses must be attached to both washer and faucet, and

have both hot and cold water owing to inlet valve.

Check that inlet valve screens are not clogged.

Remove any kinks in hoses.

First try the solutions suggested here or visit our website at www.maytag.com/help

for assistance and to possibly avoid a service call.

Not all settings and options are

available for all cycles.

Warm* selection not

available

See the “Cycle Guide” for the available settings and options for

each cycle.

Select RINSE/DRAIN & SPIN to remove any water remaining in

the washer. The washer door will unlock at the end of the drain.

Water remaining in washer after cycle.

Door locked at end of

wash cycle.

Spin speed set to No Spin. Fresh Hold

option not

selectable

Fresh Hold

option is not available if No Spin is selected.

For best performance, not all

settings are available with each cycle,

and some options cannot be used

together.

Desired setting or

option does not light

See the “Cycle Guide” for the available settings and options for

each cycle.

Using cycles with a lower spin speed.

Cycles with lower spin speeds remove less water than cycles

with high spin speeds. Use the recommended cycle/speed spin

for your garment.

Washer not loaded as recommended.

Small items may have been caught in pump.

Empty pockets and use garment bags

for small items.

A tightly packed or unbalanced load may not allow the washer

to spin correctly, leaving the load wetter than normal. See “Cycle

Guide” for load size recommendation for each cycle.

Washer not draining/

spinning, loads are

still wet

Drain hose extends into standpipe

farther than 4.5" (114 mm).

Check drain hose for proper installation. Use drain hose form

and securely attach to drainpipe or tub. Do not tape over drain

opening.

Not using HE detergent or using too

much HE detergent.

Use only HE detergent. Suds from regular detergent or using too

much detergent can slow or stop draining or spinning. Always

measure and follow manufacturer’s directions for your load.

To remove extra suds, Select RINSE/DRAIN & SPIN. Do not add

detergent.

The load may be out of balance.

Avoid washing single items. Balance a single item such as a rug

or jeans jacket with a few extra items.

The drain hose is clogged, or the

end of the drain hose more than

96" (2.4 m) above the oor.

Lower drain hose if the end is higher than 96" (2.4 m) above the

oor. Remove any clogs from drain hose. See “Installation

Requirements.”

The drain hose ts too tightly

in the standpipe, or is it taped

to the standpipe.

The drain hose should be loose yet t securely. Do not seal the

drain hose with tape. The hose needs an air gap. See Secure the

Drain Hose.”

The drum has clothing stuck between

spin basket and outer tub.

Rotate drum by hand to check for any binding of the spin

basket and outer tub. Move open end drum up and down while

holding outer tub steady and check for looseness (more than

1/4" (6.35 mm) of movement).

If the “Add A Garment” light is lit, press START/PAUSE once.

The door will unlock.

Door locks when cycle has started.

Door will not unlock

Washing many loads. Your hot water tank may not have enough hot water to keep up

with the number of hot or warm washes. This is normal.

TROUBLESHOOTING

La page charge ...

Maytag FRONT-LOADING AUTOMATIC WASHER W10254495A Mode d'emploi

Marque: Maytag

Modèle: FRONT-LOADING AUTOMATIC WASHER W10254495A

Catégorie: Machines à laver

Taper: Mode d'emploi

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag FRONT-LOADING AUTOMATIC WASHER W10254495A User guide

Maytag FRONT-LOADING AUTOMATIC WASHER W10254495A Mode d'emploi

Ce manuel convient également à

Maytag FRONT-LOADING AUTOMATIC WASHER W10254495A Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents