W10254495B
W10254496B - SP
If you have any problems or questions, visit us at www.maytag.com
Pour tout problème ou question, consulter www.maytag.ca
Designed to use only HE
High Efciency detergents.
Conçue pour l’utilisation
d’un détergent haute
efcacité seulement.
Certied to Sanitize and to Reduce Allergens
Homologué pour assainir et pour réduire la présence
d’allergènes
Use & Care Guide
Guide d’utilisation et d’entretien
Para obtener acceso
al Manual de uso y cuidado
en español, o para obtener
información adicional acerca
de su producto, visite:
www.maytag.com
FRONT-LOADING AUTOMATIC WASHER
LAVEUSE AUTOMATIQUE À CHARGEMENT FRONTAL
2
WASHER SAFETY
TABLE OF CONTENTS
WASHER SAFETY ...................................................................2
ACCESSORIES ........................................................................3
CONTROL PANEL AND FEATURES ......................................4
USING THE DISPENSER ........................................................6
CYCLE STATUS LIGHTS .........................................................7
CYCLE GUIDE ......................................................................... 8
USING YOUR WASHER ........................................................10
WASHER MAINTENANCE ....................................................14
TROUBLESHOOTING ...........................................................17
WARRANTY ........................................................................... 24
ASSISTANCE OR SERVICE .................................. Back Cover
TABLE DES MATIÈRES
SÉCURITÉ DE LA LAVEUSE ................................................25
ACCESSOIRES ........................................................................3
TABLEAU DE COMMANDE ET CARACTÉRISTIQUES .......26
UTILISATION DU DISTRIBUTEUR ....................................... 29
TÉMOINS LUMINEUX DE PROGRAMME ...........................30
GUIDE DES PROGRAMMES ................................................31
UTILISATION DE LA LAVEUSE ............................................34
ENTRETIEN DE LA LAVEUSE ..............................................38
DÉPANNAGE .........................................................................42
GARANTIE .............................................................................51
ASSISTANCE OR SERVICE ...................... Couverture arrière
3
ACCESSORIES
Customize your new washer and dryer with the following
genuine Whirlpool accessories. For more information on options
and ordering, contact your dealer, or visit: www.maytag.com.
ACCESSOIRES
Personnalisez votre nouvelle laveuse et sécheuse grâce
aux authentiques accessoires Whirlpool suivants. Pour
plus d’informations sur les options et sur les possibilités
de commande, contactez votre revendeur ou consultez :
www.maytag.ca.
Stack Kit
If space is at a premium,
the stack kit allows the dryer
to be installed on top of
the washer.
Worksurface
The worksurface bridges the washer and
dryer, and provides a convenient working
and storage area.
15" Pedestal
Color-matched pedestals raise
the washer and dryer to a more
comfortable working height.
The large drawer provides
convenient storage.
Piédestal de 15"
Les piédestaux aux coloris assortis
surélèvent la laveuse et la sécheuse
pour les amener à une hauteur
d’utilisation plus confortable. Le
grand tiroir offre une capacité de
rangement pratique.
Surface de travail
La surface de travail établit la liaison entre
la laveuse et la sécheuse et offre une zone
de travail et d’entreposage pratique.
Ensemble de superposition
Si l’espace disponible est
restreint, l’ensemble de
superposition permet à la
sécheuse d’être installée par
dessus la laveuse.
4
power
cancel
start
pause
press and
hold to start
press and hold
for 3 seconds
steam for stains
press & hold for
drum light
fresh hold
whites
heavy duty
delicate
rinse/drain
& spin
small
load
with
clean
washer
bedding
wrinkle control
allergen
normal
soak
+
-
temp levelsoil level spin speed
extra
rinse
oxi
boost
max
extract
cycle
signal
control
lock
CONTROL PANEL AND FEATURES
9
8
Not all features and cycles are available on all models.
Steam models
Non-Steam models
POWER/CANCEL BUTTON
Press to turn the washer on and off.
Press to stop/cancel a cycle at any time.
WASH CYCLE KNOB
Turn the Wash Cycle Knob to select a cycle for your laundry
load. See “Cycle Guide” for detailed descriptions of cycles
that best suit your load.
START/PAUSE BUTTON
Press and hold to start a cycle, or press once while a cycle
is in process to pause it.
DELAY START + and - BUTTONS
Use these buttons to delay the start of the wash cycle
by up to 10 hours on models with Steam, and 8 hours
on non-Steam models.
1
2
3
4
2
1
A
D
A HE detergent
B Liquid fabric softener
C Liquid Chlorine bleach
D Oxi Boost
10
C
B
B
A
A HE detergent
B Liquid fabric softener
C Liquid chlorine bleach
10
C
3
4
5
6
power
cancel
start
pause
press and
hold to start
press and hold
for 3 seconds
whites
heavy duty
rinse/drain
& spin
small
load
with
clean
washer
wrinkle control
normal
soak
allergen
delicate
+
-
temp levelsoil level spin speed
extra
rinse
cycle
signal
control
lock
stain
clean
fresh
hold
2
1
3
4
5
6
7
9
5
5
6
7
8
LED DISPLAY AND SETTINGS BUTTONS
When you select a cycle, its default settings will light up and
the Estimated Time Remaining will be displayed. Factors
such as load size, wash temperature, and water pressure
may affect the time shown in the display. Tightly packing,
unbalanced loads, or excessive suds may cause the washer
to adjust the cycle time, as well.
Use the buttons along the bottom of the display to adjust
settings. See “Cycle Guide” for available settings on each
cycle. Not all settings are available with all cycles.
Temp Level
The recommended wash temperature is preset for each
cycle. You may also select a wash temperature based
on the type of fabric and soils being washed. For best
results, use the warmest wash water safe for your
fabric, following the garment label instructions. All wash
temperatures feature a cold rinse, except Warm*, which
has a warm wash and a warm rinse.
Soil Level
Soil level (wash time) is preset for each wash cycle. As you
press the Soil Level button, the cycle time will increase or
decrease in the Estimated Time Remaining display.
For most loads, use the soil level that is preset with the
cycle you have chosen. For heavily soiled and sturdy
fabrics, press Soil Level to select more wash time. For
lightly soiled and delicate fabrics, press Soil Level to
select less wash time. Lower soil level settings will help
reduce tangling and wrinkling.
Spin Speed
This washer automatically selects the spin speed based
on the cycle selected. Preset speeds can be changed.
• Faster spin speeds mean shorter dry times, but may
increase wrinkling in your load.
• Slower spin speeds reduce wrinkling, but will leave
your load more damp.
Cycle Status Lights
The indicator bar along the right side of the display will
let you know what stage of the wash cycle is in process,
as well as when the door is locked or if you can still add
an item. For more information on each stage, see “Cycle
Status Lights”.
OPTION BUTTONS
Use these buttons to activate additional wash options
or additional features on the washer. Not all options are
available on all models or all cycles. See the “Cycle Guide”
for information on which cycles include which options.
Extra Rinse
Activate this option to add an extra rinse to most cycles.
NOTE: Some cycles include this feature as a default. See
“Cycle Guide” for details.
Oxi Boost (on some models)
Turn this option on when using Oxi boost products in the
dispenser to ensure they are dispensed at the optimal
time in the cycle.
Max Extract™ (on some models)
Max Extract™ uses an extended high-speed spin to
remove additional water during the spin. This helps reduce
drying times.
Stain Clean (on some models)
The Stain Clean option adds additional soak and wash
time to many cycles to help remove tough stains.
An integrated heater helps to maintain optimal wash
temperatures.
Cycle Signal
Use this option to adjust volume of the signal that sounds
at end of cycle.
NOTE: You may also turn off the tones that sound when a
button is pressed. Press and hold the Cycle Signal button
for about one second to turn button sounds on or off.
Control Lock
Press and hold for 3 seconds to lock the controls to
avoid unwanted changes or operation. Press and
hold 3 seconds again to unlock. The indicator will light
to show when controls are locked. You may still press
START/PAUSE to pause the cycle, or press the POWER/
CANCEL button to turn the washer off.
DRUM LIGHT (Steam models only)
Steam models feature an LED drum light. Press and hold
Steam for Stains to turn the LED drum light on or off. The
light will also turn on when the door is open, and turn off
automatically after about 5 minutes.
STEAM FOR STAINS (Steam models only)
The Steam for Stains option adds additional soak and
wash time to many cycles to help remove tough stains.
An integrated heater helps to maintain optimal wash
temperatures. Steam for Stains includes a Steam boost for
added cleaning power. See the “Cycle Guide” for cycles that
allow the Steam for Stains option.
FRESH HOLD
®
OPTION
With the washer on, press to activate the Fresh Hold
®
option. This will periodically tumble the load after the end
of the cycle for up to 16 hours while the integrated fan
circulates air through the washer to reduce humidity. You
may also activate the Fresh Hold
®
option without running a
cycle by pressing and holding for 3 seconds, then pressing
START/PAUSE.
NOTES:
• The door will lock while the Fresh Hold
®
option is active.
Press the POWER/CANCEL button to stop the cycle and
unlock the door.
• Fresh Hold
®
is not available if the spin speed is set to
No Spin.
DISPENSER DRAWER
The dispenser drawer gives you the convenience of
automatically adding HE detergent, liquid chlorine bleach,
and liquid fabric softener to the wash load at the proper
time. Steam models also feature an Oxi /color-safe bleach
compartment. See “Using the Dispenser” for information on
using the dispenser drawer.
9
High Efciency “HE” detergent compartment
This compartment holds liquid or powdered HE
detergent for your main wash cycle.
For models without an Oxi dispenser compartment,
liquid or powdered color-safe bleach or Oxi
booster product may be added to the HE detergent
compartment along with the same type of detergent,
liquid or powdered.
Liquid fabric softener compartment
Automatically dilutes and dispenses liquid fabric
softener at the optimal time in the cycle.
NOTE:
Use only liquid fabric softener in this dispenser.
Liquid chlorine bleach compartment
Automatically dilutes and dispenses liquid chlorine
bleach at the optimal time during the rst rinse after the
wash cycle. This compartment cannot dilute powdered
bleach.
Oxi Boost compartment (Steam models only)
This compartment holds measured liquid or powdered
Oxi booster product and dispenses it at the proper time
in the cycle. See the “Cycle Guide” for cycles that offer
the Oxi Boost option.
B
C
A
D
10
6
USING THE DISPENSER
Pour a measured amount of HE
detergent into detergent compartment.
For powdered detergent, slide the
selector to the left. For liquid detergent,
slide the selector to the right.
Do not overll; adding too much
detergent may cause detergent to be
dispensed into the washer too early.
Use only High Efciency
(HE) detergent.
Powdered detergent:
Slide the selector to the left.
Liquid detergent:
Slide the selector to the right.
Pour a measured amount of HE
detergent into detergent compartment.
For powdered detergent, slide the
selector to the left. For liquid detergent,
slide the selector to the right.
Do not overll; adding too much
detergent may cause detergent to be
dispensed into the washer too early.
Use only High Efciency
(HE) detergent.
Powdered detergent:
Slide the selector to the left.
Liquid detergent:
Slide the selector to the right.
Models with a 4-compartment dispenser
Models with a 3-compartment dispenser
If you would like to use powdered or liquid oxi-type
boosters or color-safe bleach, follow the manufacturer’s
recommendations for placement. If no recommendation
is available, you may add powdered or liquid oxi-type
boosters or color-safe bleach to the detergent
compartment with the same type of detergent,
powdered or liquid.
IMPORTANT:
n
Do not add single-dose laundry packet to dispenser
drawer.
n
Use powdered detergent when using the Delay Wash
option. Liquid detergent may seep out before the
wash begins.
HE detergent
compartment
HE detergent
compartment
To use the dispenser drawer:
1. Open the dispenser drawer.
2. Add laundry products as described in steps 4–6.
3. Slowly close the dispenser drawer. Make sure it is
completely closed.
NOTE: A small amount of water may remain in the dispensers
from the previous wash cycle. This is normal.
IMPORTANT:
n
Do not add single-dose laundry packet to dispenser
drawer.
n
Use powdered detergent when using the Delay Wash
option. Liquid detergent may seep out before the wash
begins.
7
CYCLE STATUS LIGHTS
The Cycle Status Lights show the progress of a cycle. At each
stage of the process, you may notice sounds or pauses that are
different from traditional washers.
Door Locked
Door Locked will light to indicate that the door is locked and
cannot be opened without rst pausing or canceling the cycle.
Sensing
When the START/PAUSE button is pressed, the washer will
rst perform a self-test on the door lock mechanism. You will
hear a click, the drum will make a partial turn, and the door
will unlock briey before locking again.
Once the door has locked the second time, the washer will
begin tumbling and adding water. This sensing process will
continue until the correct amount of water has been added
for the load. You may also hear water owing through the
dispenser, adding detergent to the load.
The displayed time may change as the washer goes through
the sensing process. This is normal.
Add a Garment
When Add a Garment is lit, you may pause the washer, open
the door, and add items.
Sanitized
Sanitized will light on cycles with a Sanitize setting once the
load has been washed at the proper temperature for the
necessary time to meet NSF Sanitization requirements.
Delay
The Delay indicator will light if a Delay Start has been set.
Once the programmed delay has ended, the indicator will
turn off and the cycle will begin.
Wash
This is the main portion of the wash cycle. You will see the
washer tumble the load. The motor sounds may change at
different stages in the cycle. The wash time is determined by
the selected cycle and soil level along with your load size.
Rinse
You will hear sounds similar to the wash cycle as the
washer rinses and moves the load. If used, liquid chlorine
bleach is added in the rst rinse. Fabric Softener is added
in the last rinse.
Spin
The washer spins the load at increasing speeds for
proper water removal, based on the selected cycle
and spin speed.
Steam (on some models)
This will light to show that the cycle is using a Steam boost
for added cleaning power.
Done
Once the cycle is complete, this light will come on.
Remove the load promptly for best results.
Fresh Hold
®
The Fresh Hold
®
indicator will light when the Fresh
Hold
®
option is active. During this time, the washer
will occasionally tumble the load while a fan circulates
fresh air through the washer.
Steam model shown
+
-
temp level soil levelspin speed
8
CYCLE GUIDE — STANDARD CYCLES
Normally soiled cottons, Normal Hot High Extra Heavy Extra Rinse This cycle combines medium-speed
linens, sheets, and Warm/Cold* Medium Heavy Stain Clean
1
tumbling and a high-speed spin.
mixed garment loads Warm/Warm No Spin Normal Max Extract™ This cycle is designed to provide
Cold Light Oxi Boost the most energy efciency.
Fresh Hold
®
Delay Start
Sturdy colorfast Heavy Sanitize
†
High Extra Heavy Extra Rinse High-speed tumbling and a
fabrics and heavily Duty Hot Medium Heavy Stain Clean
1
high-speed nal spin help
soiled garments, Warm/Cold* Low Normal Max Extract™ provide optimal cleaning and
towels, and jeans Warm/Warm No Spin Light Oxi Boost reduce drying times.
Cold Fresh Hold
®
Delay Start
Heavily soiled white Whites Sanitize
†
High Extra Heavy Extra Rinse Hot wash temperatures ensure
fabrics and garments Hot Medium Heavy Stain Clean
1
liquid chlorine bleach action.
Warm/Cold* Low Normal Max Extract™ An Extra Rinse helps remove
Warm/Warm No Spin Light Oxi Boost any bleach residue in clothes.
Cold Fresh Hold
®
Delay Start
Heavily soiled Power Wash Sanitize
†
High Extra Heavy Extra Rinse Features an extended wash time
durable fabrics, Hot Medium Heavy Stain Clean
1
to help remove tough stains.
overalls, coveralls, Warm/Cold* Low Normal Max Extract™ Stain Clean/Steam for Stains
sweatshirts, pants, and Warm/Warm No Spin Light Oxi Boost (depending on model) is
outdoor garments Cold Fresh Hold
®
automatically added for extra
Delay Start cleaning power.
Lightly-soiled shirts, Wrinkle Hot Medium Extra Heavy Extra Rinse This cycle combines low-speed
blouses, trousers, Control Warm/Warm Low Heavy Stain Clean
1
tumbling and low-speed spin
pants and dresses Cold Extra Low Normal Max Extract™ for gentle fabric care and reduced
No Spin Light Oxi Boost wrinkling
Fresh Hold
®
Delay Start
Blankets, comforters Bedding Sanitize
†
High Extra Heavy Extra Rinse Uses an initial soak to completely
Hot Medium Heavy Stain Clean
1
saturate the load, followed by
Warm/Cold* Low Normal Oxi Boost medium wash speeds and a
Warm/Warm Extra Low Light Fresh Hold
®
medium-speed spin to maintain
Cold No Spin Delay Start load balance.
Sturdy garments and Allergen
††
Sanitize
†
High Extra Heavy Extra Rinse Uses more water to ush out
household items Hot Medium Heavy Stain Clean
1
allergens such as dust mites
exposed to possible Normal Max Extract™ and pet dander from
allergens Light Oxi Boost normally-soiled items.
Fresh Hold
®
Delay Start
Sheer fabrics, Delicate Warm/Cold* High Normal Extra Rinse This cycle combines low-speed
lingerie, sweaters, Warm/Warm Medium Light Fresh Hold
®
tumbling and low-speed spin
and silks Cold Low Delay Start for gentle fabric care and reduced
Extra Low wrinkling.
No Spin
Items to wash
using default
cycle settings:
Cycle:
Wash
Temperature*:
Spin
Speed:
Soil
Level:
Available
Options:
Cycle Details:
†† Allergen
Allergen cycle certied by NSF International, an independent, third party testing and certication organization.
The certication veried that this cycle reduced tested allergens by at least 95.0% and maintained the water
temperature necessary to kill dust mites. Only the allergen cycle has been designed to meet the requirements of
NSF Protocol P351 for Allergen Reduction Performance effectiveness.
† Sanitize
Cycles certied by NSF International, an independent, third party testing and certication organization are those with the
sanitize temperature selection available. The certication veried that these cycles reduce 99.9% of bacteria typically
found on clothing, bedding, and towels. There is no carryover of bacteria between loads after the cycle is complete.
Only cycles with sanitize wash temperature selected have been designed to meet the requirements of NSF Protocol
P172 for Sanitizing Effectiveness.
Settings and options shown in bold are default settings for that cycle. For best fabric care, choose the cycle that best ts the
load being washed.
Not all cycles and options are available on all models.
For best performance, not all settings are available with each cycle, and some options cannot be used together.
* All temperature selections feature a Cold rinse, except Warm/Warm, which features a warm wash and a warm rinse.
1
Stain Clean on non-Steam models. Steam for Stains on Steam models. See “Control Panel and Features” for additional information.
Models: MHW6000**, MHW7000**
9
Small loads of 3 - 4 Small Load Hot High Heavy Extra Rinse For small loads (3-4 items) needed
lightly soiled garments Warm/Warm Medium Normal Fresh Hold
®
quickly. This cycle combines
Cold Low Light Delay Start high-speed tumbling, a shortened
Extra Low wash time, and a high-speed spin
for reduced drying times.
Swimwear, items Rinse/Drain Warm/Cold* High N/A Extra Rinse This cycle adds water, then uses
that need rinsing only & Spin Warm/Warm Medium Max Extract™ high-speed tumbling and an extra
Cold Low Fresh Hold
®
high-speed spin. For some fabrics,
Extra Low Delay Start you may wish to set the spin speed
No Spin to a lower setting.
Wet load of clothes Rinse/Drain N/A High N/A Max Extract™ Use Drain & Spin to remove excess
& Spin Medium Fresh Hold
®
water from the load by choosing
Low Delay Start Rinse/Drain & Spin and turning off
Extra Low Extra Rinse. Spin speed can be set
No Spin to a lower setting.
Heavily soiled garments Soak Warm/Cold* Extra Heavy Fresh Hold
®
Provides an extended soak without
Warm/Warm Heavy Delay Start a nal spin to help loosen tough
Cold Normal stains prior to a wash cycle.
Light
No clothes in washer Clean Washer Use this cycle every 30 washes to
with affresh
®
keep the inside of your washer fresh
and clean. This cycle uses a higher
water level. Use with affresh
®
Washer Cleaner tablet or liquid
chlorine bleach to thoroughly clean
the inside of your washer. This cycle
should not be interrupted. See
“Washer Care.”
IMPORTANT: Do not place
garments or other items in the
washer during the Clean Washer
with affresh
®
cycle. Use this cycle
with an empty wash tub.
CYCLE GUIDE — SPECIAL-PURPOSE CYCLES
Cycle:
Wash
Temperature*:
Spin
Speed:
Soil
Level:
Available
Options:
Cycle Details:
Load Size Recommendations
For best results, follow the load size recommendations noted for each cycle.
Small load: Fill the washer drum with 3-4 items, not more than 1/4 full.
Medium load: Fill the washer drum up to about 1/2 full.
Large load: Fill the washer drum up to about 3/4 full.
Extra-large load: Fill the washer drum, but make sure clothes can tumble freely.
For best results, avoid packing tightly.
* All temperature selections feature a Cold rinse, except Warm/Warm, which features a warm wash and a warm rinse.
Settings and options shown in bold are default settings for that cycle. For best fabric care, choose the cycle that best ts the
load being washed.
Not all cycles and options are available on all models.
For best performance, not all settings are available with each cycle, and some options cannot be used together.
Items to wash
using default
cycle settings:
10
USING YOUR WASHER
Sort items by recommended cycle, water temperature, and
colorfastness. Separate heavily soiled items from lightly soiled.
Separate delicate items from sturdy fabrics. Treat stains
promptly and check for colorfastness by testing stain remover
products on an inside seam.
1. Sort and prepare your laundry
First wash cycle without laundry
Before washing clothes for the rst time, if not completed during
the nal installation step, choose the QUICK WASH cycle and
run it without clothes. Use only HE detergent. Use 1/2 the
manufacturer’s recommended amount for a medium-size load.
This initial cycle serves to ensure the interior is clean before
washing clothes.
Choosing the Right Detergent
Use only High Efciency detergents. The package will be
marked “HE” or “High Efciency.” Low-water washing creates
excessive sudsing with a regular non-HE detergent. Using regular
detergent will likely result in longer cycle times and reduced
rinsing performance. It may also result in component failure and,
over time, build-up of mold or mildew. HE detergents are made
to produce the right amount of suds for the best performance.
Follow the manufacturer’s instructions to determine the amount
of detergent to use.
Use only High Efciency (HE) detergent.
IMPORTANT:
n Empty pockets. Loose change, buttons, or any small object
can plug pumps and may require a service call.
n Close zippers, fasten hooks, tie strings and sashes, and
remove non-washable trim and ornaments.
n Mend rips and tears to avoid further damage to items
during washing.
n Turn knits inside out to prevent pilling. Separate lint-takers
from lint-givers. Synthetics, knits, and corduroy fabrics will
pick up lint from towels, rugs, and chenille fabrics.
n Do not dry garments if stains remain after washing, because
heat can set stains into fabric.
n Always read and follow fabric care labels and laundry
product instructions. Improper usage may cause damage
to your garments.
2. Add single-dose laundry packet, Oxi,
or color-safe bleach (if desired)
Single-dose laundry packet, Oxi-type boosters, or color-safe
bleach can be added to the drum prior to adding laundry.
(Some models Oxi and bleach can be added to dispenser
drawer).
11
Add a measured amount of liquid chlorine bleach to the
bleach compartment. Do not overll, dilute, or use more than
2/3 cup (165 mL). Use a measuring cup with a pour spout; do
not guess.
n
Do not ll beyond the “MAX” level. Overlling will cause
bleach to dispense too soon and may cause garment
damage.
n
Do not add single-dose laundry packet, oxi-product, or
color-safe bleach to this dispenser. It will not dispense
correctly. See “Using the Dispenser” instructions on how
to use the dispenser.
6. Add liquid chlorine bleach
to dispenser (if desired)
Pour a measured amount of liquid fabric softener into liquid
fabric softener compartment. Always follow manufacturer’s
directions for correct amount of fabric softener based on your
load size.
Fabric softener is always dispensed in the last rinse, even if
Extra Rinse is selected.
IMPORTANT: Do not overll, dilute, or use more than 1/4 cup
(60 mL) of fabric softener. Do not ll past the MAX line.
Overlling dispenser will cause fabric softener to immediately
dispense into washer.
n
Do not spill or drip any fabric softener onto the clothes.
n
Do not use liquid fabric softener dispenser balls in this
washer. They will not dispense correctly.
5. Add fabric softener to dispenser
(if desired)
Liquid fabric
softener
compartment
4-compartment dispenser shown
Liquid chlorine
bleach
compartment
4-compartment dispenser shown
Open the washer door. Place a load of sorted clothes loosely in
the washer. Items need to move freely for best cleaning and to
reduce wrinkling and tangling. Close the washer door by pushing
it rmly until the latch clicks.
n Depending on load type and cycle, the washer can be fully
loaded, but not tightly packed. Washer door should close
easily. See “Cycle Guide” for loading suggestions.
n Mix large and small items and avoid washing single items.
Load evenly.
n Wash small items in mesh garment bags. For multiple items,
use more than one bag and ll bags equally.
3. Load laundry into washer
Select detergent dispenser, based on type of HE detergnet
used (liquid or powdered). See “Using the Dispenser”
instructions on how to use the dispenser.
4. Add HE detergent
3-compartment dispenser
4-compartment dispenser
12
power
cancel
8. Press POWER/CANCEL to turn
on washer
Slowly close the dispenser drawer. Make sure the drawer is
closed completely, then press and hold POWER/CANCEL to
turn on the washer.
whites
heavy duty
delicate
rinse/drain
& spin
small
load
with
clean
washer
bedding
wrinkle control
allergen
normal
soak
9. Select CYCLE
The display will show the default settings for the selected
cycle. If desired, press the button beneath each setting to
adjust the Temp Level, Soil Level, and Spin Speed. Adjusting
the Soil Level will change the Estimated Time Remaining.
Tightly packing, unbalanced loads, or excessive suds may also
cause the washer to increase the cycle time.
NOTE: Not all settings are available on all cycles. See “Cycle
Guide” for available settings.
Turn cycle knob to select your wash cycle. See “Cycle Guide”
for details on cycle features. Not all options and settings are
available on all cycles.
press and hold
for 3 seconds
+
-
temp level soil levelspin speed
extra
rinse
oxi
boost
max
extract
cycle
signal
control
lock
10. Adjust settings, if desired
Steam model shown
Steam model shown
press and hold
for 3 seconds
steam for stains
press & hold for
drum light
fresh hold
extra
rinse
oxi
boost
max
extract
cycle
signal
control
lock
11. Select any additional options
To add additional options to the cycle, such as Extra Rinse,
Fresh Hold
®
, Stain Clean/Steam for Stains (on some models),
or Max Extract™ (on some models), press the button for the
desired options to add them to the selected cycle.
NOTE: Not all options are available with all cycles. See “Cycle
Guide” for available options.
Steam model shown
On models with a 4-compartment dispenser,
add Oxi booster or Color-Safe Bleach to the
Oxi compartment. Be sure to select the
Oxi Boost option.
n
Always follow the manufacturer’s recommendations.
For models without an Oxi compartment:
If you would like to use powdered or liquid oxi-type boosters or
color-safe bleach, follow the manufacturer’s recommendations
for placement. If no recommendation is available, you may add
powdered or liquid oxi-type boosters or color-safe bleach to
the detergent compartment with the same type of detergent,
powdered or liquid.
7. Add Oxi or Color-Safe Bleach
(on some models)
Oxi/Color-Safe Bleach
compartment
4-compartment dispenser shown
oxi
boost
13
12. Setting a delayed start
If you do not want to begin a cycle immediately, you may
choose the DELAY START option. This will delay the start
of the wash cycle by up to 10 hours on models with Steam,
and 8 hours on non-Steam models.
To set a delayed Start:
1. Press DELAY START s and t buttons to set the desired
delay time.
2. Press START/PAUSE to set the delay. The delay countdown
has started when the START/PAUSE light stops blinking.
+
-
temp level soil le
vel
start
pause
press and
hold to start
13. Press and hold START/PAUSE
to begin wash cycle
Press and hold the START/PAUSE button to start the wash
cycle. To pause a cycle in progress, press the START/PAUSE
button once, then press and hold again to continue the cycle.
To cancel a cycle, press the POWER/CANCEL button.
Once you press and hold START/PAUSE, you will hear the
door lock, unlock, and lock again. The washer door will remain
locked during the wash cycle.
Unlocking the door to add garments:
If you need to open the door to add 1 or 2 missed garments,
you may do so while the “Add a Garment” light is lit.
Press START/PAUSE once; the door will unlock
once the washer movement has stopped.
This may take several minutes. Then close
door and press START/PAUSE again to restart
the cycle.
start
pause
press and
hold to start
14. Remove garments promptly
after cycle is nished
Promptly remove garments after cycle has
completed to avoid odor and rusting of
metal objects on garments. When unloading
garments, pull back the door seal and check
for small items between the tub and the
washer drum.
If you will be unable to remove the load
promptly, use the Fresh Hold
®
option. If the
Fresh Hold
®
option is selected, the washer will
automatically activate the fan and tumble
the load periodically for up to 16 hours.
NOTE:
n
After any wash cycle is completed,
the door must be opened and then
closed before a new cycle can begin.
n
A small amount of water may remain in the dispensers after
the wash cycle is complete. This is normal.
n
This washer has a tight seal to avoid water leaks. To avoid
odors, leave the door open to allow the washer to dry
between uses.
fresh
hold
14
WASHER MAINTENANCE
Replace inlet hoses after 5 years of use to reduce the risk
of hose failure. Periodically inspect and replace inlet hoses
if bulges, kinks, cuts, wear, or leaks are found.
When replacing your inlet hoses, mark the date of
replacement on the label with a permanent marker.
NOTE: This washer does not include inlet hoses. See the
“Installation Instructions” for more information.
WATER INLET HOSES
WASHER CARE
Recommendations to Help Keep Your Washer Clean
and Performing at its Best
1. Always use High Efciency (HE) detergents and follow the
HE detergent manufacturer’s instructions regarding the
amount of HE detergent to use. Never use more than the
recommended amount because that may increase the
rate at which detergent and soil residue accumulate inside
your washer, which in turn may result in undesirable odor.
2. Use warm or hot water washes sometimes (not exclusively
cold water washes), because they do a better job of
controlling the rate at which soils and detergent accumulate.
3. Always leave the washer door slightly ajar between uses
to help dry out the washer and prevent the buildup of
odor-causing residue.
Cleaning Your Front Loading Washer
Read these instructions completely before beginning the
routine cleaning processes recommended below. This
Washer Maintenance Procedure should be performed,
at a minimum, once per month or every 30 wash cycles,
whichever occurs sooner, to control the rate at which soils
and detergent may otherwise accumulate in your washer.
Cleaning the Door Seal
1. Open the washer door and remove any clothing or items
from the washer.
2. Inspect the seal between the door opening and the drum
for stained areas or soil buildup. Pull back the seal to
inspect all areas under the seal and to check for foreign
objects.
3. If stained areas or soil buildup are found, wipe down
these areas of the seal using either of the following
two procedures:
a. affresh
®
Grit Grabber™ Cloth Procedure:
i. When the cycle is complete, gently pull back the
rubber door seal and clean the entire surface with
the rough side of the Grit Grabber™ cloth.
b. Dilute Liquid Chlorine Bleach Procedure:
i. Mix a dilute bleach solution, using 3/4 cup (177 mL)
of liquid chlorine bleach and 1 gallon (3.8 L) of warm
tap water.
ii. Wipe the seal area with the dilute solution, using
a damp cloth.
iii. Let stand 5 minutes.
iv. Wipe down area thoroughly with a dry cloth and let
washer interior air dry with door open.
IMPORTANT:
n Wear rubber gloves when cleaning with bleach.
n Refer to the bleach manufacturer’s instructions
for proper use.
WASHER CARE (cont.)
Cleaning the Inside of the Washer
This washer has a special cycle that uses higher water
volumes in combination with affresh
®
Washer Cleaner or
liquid chlorine bleach to thoroughly clean the inside of the
washer. Steam washer models also utilize steam to enhance
cleaning in this special cycle.
NOTE: Read these instructions completely before beginning
the cleaning process.
Begin procedure
1. affresh
®
Washer Cleaner Cycle Procedure
(Recommended):
a. Open the washer door and remove any clothing
or items.
b. Add an affresh
®
Washer Cleaner tablet to the washer
drum.
c. Do not add the affresh
®
Washer Cleaner tablet
to the dispenser drawer.
d. Do not add any detergent or other chemical to the
washer when following this procedure.
e. Close the washer door.
f. Select the CLEAN WASHER cycle.
g. Press the START button to begin the cycle. The Clean
Washer Cycle Operation is described below.
2. Chlorine Bleach Procedure:
a. Open the washer door and remove any clothing
or items.
b. Open the dispenser drawer and add 2/3 cup (160 mL)
of liquid chlorine bleach to the bleach compartment.
NOTE: Use of more liquid chlorine bleach than is
recommended above could cause product damage
over time.
c. Close the washer door and the dispenser drawer.
d. Do not add any detergent or other chemical to the
washer when following this procedure.
e. Close the washer door.
f. Select the CLEAN WASHER cycle.
g. Press the START button to begin the cycle. The Clean
Washer Cycle Operation is described below.
Description of Clean Washer Cycle Operation:
1. The Clean Washer cycle will determine whether clothing
or other items are in the washer.
2. If no items are detected in the washer, it will proceed
to step 3.
a. If any items are detected in the washer, “rL” (remove
load) will be displayed, and the washer “Controls Lock”
lights will remain lit. The door will unlock. Open washer
and remove any garments from the washer drum.
b. Press PAUSE/CANCEL or POWER/CANCEL
to clear the “rL” code.
c. Press START to restart the cycle.
3. After the cycle is complete, leave the door open slightly to
allow for better ventilation and drying of the washer interior.
15
WASHER CARE (cont.)
Cancellation of Clean Washer Cycle Operation:
If the Clean Washer cycle is canceled by the user after it has
been initiated, it may take up to 30 minutes for the washer
to purge any affresh
®
Cleaner, chlorine bleach, or other
chemistry from the wash system and to adequately rinse any
remaining chemistry. The washer door will remain locked until
the cancellation process has been completed. This assures
no cleaning chemistry will be carried over to the next wash
cycle and reduces the potential for damage to subsequent
loads of laundry or to the machine itself.
Clean Washer Cycle Cancellation Procedure:
1. Press the PAUSE/CANCEL or the POWER/CANCEL
button on the washer two times.
2. Washer will begin to drain and rinse away the remaining
cleaning chemistry.
3. The cycle will complete the cancellation process in
approximately 30 minutes or less.
4. The washer then can be used to either repeat the Clean
Washer cycle or to wash laundry using one of the regular
wash cycles selected by the user.
Cleaning the Outside of the Washer
Use a soft, damp cloth or sponge to wipe up any spills.
Occasionally wipe the outside of your washer to help
keep it looking new. Use mild soap and water.
IMPORTANT: To avoid damaging the washer’s nish, do not
use abrasive products.
CLEANING THE DISPENSER
You may nd laundry product residue leftover in your
dispenser compartments. To remove residue, follow this
recommended cleaning procedure:
1. Pull dispenser drawer out until it stops.
2. Press down on the release tab and pull straight out to
remove the dispenser.
CLEANING THE DISPENSER (cont.)
3. Lift off cover panel by
pulling straight up.
4. Wash dispenser and
cover panel in warm,
soapy water, using a mild
detergent.
5. Rinse with warm water.
6. Air dry or wipe with a
clean towel, slide cover
panel back onto posts on
dispenser.
7. Align edges of dispenser
with guides in washer,
then slide dispenser
back into slot.
IMPORTANT: Dispenser is
not dishwasher safe.
16
Operate your washer only when you are home. If moving,
or not using your washer for a period of time, follow these
steps:
1. Unplug or disconnect power to washer.
2. Turn off water supply to washer to avoid ooding due
to water pressure surges.
NON-USE AND VACATION CARE
WINTER STORAGE CARE
IMPORTANT: To avoid damage, install and store washer
where it will not freeze. Because some water may stay in
hoses, freezing can damage washer. If storing or moving
during freezing weather, winterize your washer.
To winterize washer:
1. Shut off both water faucets, disconnect and drain water
inlet hoses.
2. Put 1 qt. (1 L) of R.V.-type antifreeze in washer drum
and run washer on RINSE AND SPIN cycle for about
1 minute to mix antifreeze and remaining water.
3. Unplug washer or disconnect power.
IMPORTANT: To reduce risk of hose failure, replace inlet
hoses every ve years and periodically inspect for kinks,
cuts, wear or water leaks.
HELPFUL TIP: When replacing your inlet hoses, mark
replacement date on label with a permanent marker.
TRANSPORTING YOUR WASHER
1. Shut off both water faucets. Disconnect and drain water
inlet hoses.
2. If washer will be moved during freezing weather, follow
WINTER STORAGE CARE directions before moving.
3. Disconnect drain hose from drain system and from back
of washer.
4. Unplug power cord.
5. Place inlet hoses and drain hose inside washer drum.
6. Bundle power cord with a rubber band or cable tie to
keep it from hanging onto the ground.
IMPORTANT: Call for service to install new transport bolts.
Do not reuse transport bolts. Washer must be transported
in the upright position. To avoid structural damage to your
washer, it must be properly set up for relocation
by a certied technician.
REINSTALLING/USING WASHER AGAIN
To reinstall washer after non-use, vacation, winter storage,
or moving:
1. Refer to Installation Instructions to locate, level, and
connect washer.
2. Before using again, run washer through the following
recommended procedure:
To use washer again:
1. Flush water pipes and hoses. Reconnect water inlet
hoses. Turn on both water faucets.
2. Plug in washer or reconnect power.
3. Run washer through POWER WASH cycle to clean
washer and remove antifreeze, if used. Use only HE
detergent. Use half the manufacturer’s recommended
amount for a medium-size load.
17
If you experience
Possible Causes
Solution
First try the solutions suggested here or visit our website at www.maytag.com/help
for assistance and to possibly avoid a service call.
Error Code Appears in Display
Sud (Excess suds)
appears in display
Excessive suds in washer. Washer is
running a suds reduction routine.
Allow the machine to continue. Use only HE detergent.
Always measure detergent, and base detergent quantity on
load size. Follow detergent manufacturer’s instructions.
Press POWER/CANCEL once to clear the code. Then press
POWER/CANCEL again to restart washer. If code appears
again, call for service.
F8E1 (water supply
error) appears in display
Check for proper water supply.
Both hoses must be attached and have water owing to the
inlet valve.
Both hot and cold water faucets must be on.
Inlet valve screens on washer may be clogged.
Remove any kinks in the inlet hose.
F9E1 (drain pump
system error) appears
in display
Check plumbing for correct drain
hose installation. Drain hose extends
into standpipe farther than 4
1
⁄
2
”
(114 mm).
Check drain hose for proper installation.
Make sure the drain hose is not kinked, pinched, or blocked.
Remove any clogs from drain hose.
Use drain hose form and securely attach to drainpipe or tub.
Lower drain hose if the end is higher than 96" (2.4 m) above
the oor.
F5E2 (door will not lock)
appears in display
Washer door not locking.
Press POWER/CANCEL to cancel the cycle. Make sure the
door is closed completely and latching. Check for items in
the washer drum that may be keeping the door from closing
completely.
Washer beeps when
START/PAUSE is
pressed.
Door not closed.
Close the door completely.
F7E1 (motor drive error)
appears in display
Motor is having difculty turning
the drum.
Washer is tightly packed. Remove some items. See “Cycle
Guide” for load size recommendations.
Make sure that all shipping materials have been removed. See
the Installation Instructions.
“rL” (remove load)
appears in display
Load detected in drum during Clean
Washer with affresh
®
cycle.
Remove items from drum and restart Clean Washer
with affresh
®
cycle.
Washer making error
beeps.
Door has not been opened and closed
for at least 3 cycles.
This code may appear when the washer is rst turned on.
Open and close the door to clear the display.
Once any possible issues are corrected, press POWER/CANCEL once to clear the code. Reselect and restart the cycle.
F#E# code other than
as described above
appears in display
System error code.
Press POWER/CANCEL once to clear the code. Then press
POWER/CANCEL again to restart washer. If code appears
again, call for service.
Not using HE detergent or using too
much HE detergent.
Use only HE detergent. Always measure detergent and follow
manufacture’s directions based on load size and soil level.
TROUBLESHOOTING
18
First try the solutions suggested here or visit our website at www.maytag.com/help
for assistance and to possibly avoid a service call.
If you experience
Possible Causes
Solution
Feet may not be in contact with the
oor and locked.
Front and rear feet must be in rm contact with oor, and washer
must be level to operate properly. Jam nuts must be tight
against the bottom of the cabinet.
Check oor for exing or sagging. If ooring is uneven, a 3/4"
(19 mm) piece of plywood under your washer will reduce sound.
See “Level the Washer” in Installation Instructions.
Load could be unbalanced
or too large.
Avoid tightly packing the load. Avoid washing single items.
Balance a single item such as a rug or jeans jacket with a
few extra items.
Use Bedding cycle for oversized, non-absorbent items
such as comforters or poly-lled jackets. Other items are
not appropriate for Bedding cycle. See “Cycle Guide”.
Item or load not suitable for selected cycle. See “Cycle Guide”
and “Using Your Washer” in this Use and Care Guide.
Empty pockets before washing. Loose items such as coins
could fall between washer drum and tub or may block pump.
It may be necessary to call for service to remove items.
Fill hoses not attached tightly.
Tighten ll-hose connection.
Are all four ll hose at washers properly seated?
Drain hose connection.
Check that the drain hose is properly secured to drainpipe or
laundry tub.
Check household plumbing for leaks
or clogged sink or drain.
Water can backup out of a clogged sink or drainpipe. Check
all household plumbing for leaks (laundry tubs, drain pipe,
water pipes, and faucets.)
Fill hose washers.
Noises
It is normal to hear metal items on clothing such as metal snaps,
buckles, or zippers touch against the stainless steel drum.
Objects caught in washer
drain system.
Clicking or metallic
noises
Gurgling or humming
It is normal to hear the pump making a humming sound with
periodic gurgling or surging as nal amounts of water are removed
during the spin/drain cycles.
Washer may be
draining water.
Water Leaks
Check the following for
proper installation:
Vibration, rocking, or
“walking”
Load not completely
covered in water.
Water level not visible on door or
does not cover clothes.
This is normal for an HE front load washer. The washer senses load
sizes and adds the correct amount of water for optimal cleaning.
Washer not performing as expected
Washer may not be level.
Vibration or Off-Balance
The door will lock unlock and lock again. You will hear three
clicks after pushing start. This is normal.
Door locking or unlocking.
Not using HE detergent or using too
much HE detergent.
Only use HE detergent. Suds from regular detergents can
cause leaking from the door or rear of cabinet. Always measure
detergent and follow manufacturer’s directions based on your
load requirements.
Water or suds leaking
from door or rear of
cabinet
Residue on door glass.
Periodically clean the the underside of the glass window to
avoid potential leaks.
The shipping bolts are still in the
back of the washer.
See “Remove transport bolts from washer” in the
Installation Instructions.
Door opened during “Add A
Garment.”
Water can drip off the inside of the door when the door is
opened after the start of a cycle.
TROUBLESHOOTING
19
Normal washer operation.
Door must be completely closed and latched for washer to run.
Washer will pause during certain phases of cycle.
Do not interrupt cycle.
The washer pauses for about 2 minutes during certain cycles.
Allow the cycle to continue. Some cycles feature periods of
tumbling and soak.
Washer may be stopped to reduce suds.
Plug power cord into a grounded 3 prong outlet.
Do not use an extension cord.
Ensure there is power to outlet.
Check electrical source or call an electrician to check if voltage
is low.
Reset a tripped circuit breaker. Replace any blown fuses.
NOTE: If problems continue, contact an electrician.
Washer not loaded as recommended.
Remove several items, rearrange load evenly in drum.
Close door and press START/PAUSE.
Do not add more than 1 or 2 additional items after cycle has
started to avoid tightly packing or unbalancing.
Not using HE detergent or using too
much HE detergent.
Only use HE detergent. Suds from regular detergents can slow
or stop the washer. Always measure detergent and following
manufacturers directions based on your load requirements.
To remove suds, cancel cycle. Select RINSE/DRAIN & SPIN.
Press START/PAUSE. Do not add more detergent.
After any wash cycle is completed, the door must be opened
and then closed before a new cycle can begin.
Do not add more water to the washer.
Door not opened between cycles.
If you experience
Possible Causes
Solution
Washer won’t run or ll,
washer stops working
Check for proper water supply.
Both hoses must be attached and have water owing to
inlet valve.
Both Hot and Cold water faucets must be turned on.
Check that inlet valve screens have not become clogged.
Check for any kinks in inlet hoses, which can restrict water ow.
Check proper electrical supply.
First try the solutions suggested here or visit our website at www.maytag.com/help
for assistance and to possibly avoid a service call.
Washer not performing as expected (cont.)
The washer door is not rmly shut. The door must be closed during operation.
TROUBLESHOOTING
20
Washer not performing as expected (cont.)
If you experience
Possible causes
Solution
Incorrect or wrong
wash or rinse
temperatures
Check for proper water supply.
Make sure hot and cold inlet hoses are not reversed.
Both hoses must be attached to both washer and faucet, and
have both hot and cold water owing to inlet valve.
Check that inlet valve screens are not clogged.
Remove any kinks in hoses.
First try the solutions suggested here or visit our website at www.maytag.com/help
for assistance and to possibly avoid a service call.
Not all settings and options are
available for all cycles.
Warm* selection not
available
See the “Cycle Guide” for the available settings and options for
each cycle.
Select RINSE/DRAIN & SPIN to remove any water remaining in
the washer. The washer door will unlock at the end of the drain.
Water remaining in washer after cycle.
Door locked at end of
wash cycle.
Spin speed set to No Spin. Fresh Hold
®
option not
selectable
Fresh Hold
®
option is not available if No Spin is selected.
For best performance, not all
settings are available with each cycle,
and some options cannot be used
together.
Desired setting or
option does not light
See the “Cycle Guide” for the available settings and options for
each cycle.
Using cycles with a lower spin speed.
Cycles with lower spin speeds remove less water than cycles
with high spin speeds. Use the recommended cycle/speed spin
for your garment.
Washer not loaded as recommended.
Small items may have been caught in pump.
Empty pockets and use garment bags
for small items.
A tightly packed or unbalanced load may not allow the washer
to spin correctly, leaving the load wetter than normal. See “Cycle
Guide” for load size recommendation for each cycle.
Washer not draining/
spinning, loads are
still wet
Drain hose extends into standpipe
farther than 4.5" (114 mm).
Check drain hose for proper installation. Use drain hose form
and securely attach to drainpipe or tub. Do not tape over drain
opening.
Not using HE detergent or using too
much HE detergent.
Use only HE detergent. Suds from regular detergent or using too
much detergent can slow or stop draining or spinning. Always
measure and follow manufacturer’s directions for your load.
To remove extra suds, Select RINSE/DRAIN & SPIN. Do not add
detergent.
The load may be out of balance.
Avoid washing single items. Balance a single item such as a rug
or jeans jacket with a few extra items.
The drain hose is clogged, or the
end of the drain hose more than
96" (2.4 m) above the oor.
Lower drain hose if the end is higher than 96" (2.4 m) above the
oor. Remove any clogs from drain hose. See “Installation
Requirements.”
The drain hose ts too tightly
in the standpipe, or is it taped
to the standpipe.
The drain hose should be loose yet t securely. Do not seal the
drain hose with tape. The hose needs an air gap. See Secure the
Drain Hose.”
The drum has clothing stuck between
spin basket and outer tub.
Rotate drum by hand to check for any binding of the spin
basket and outer tub. Move open end drum up and down while
holding outer tub steady and check for looseness (more than
1/4" (6.35 mm) of movement).
If the “Add A Garment” light is lit, press START/PAUSE once.
The door will unlock.
Door locks when cycle has started.
Door will not unlock
Washing many loads. Your hot water tank may not have enough hot water to keep up
with the number of hot or warm washes. This is normal.
TROUBLESHOOTING
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
Maytag MHW7000XW Mode d'emploi
- Catégorie
- Machines à laver
- Taper
- Mode d'emploi
dans d''autres langues
- English: Maytag MHW7000XW User guide
Documents connexes
-
Maytag MHW6000XG Mode d'emploi
-
Maytag MHW3000 Manuel utilisateur
-
-
-
-
-
-
-
-
Maytag MHW7000AW2 Le manuel du propriétaire