Hearth and Home Technologies IntelliFire Plus RC200 Manuel utilisateur

Marque: Hearth and Home Technologies

Modèle: IntelliFire Plus RC200

Catégorie: Cheminées

Taper: Manuel utilisateur

Ce manuel convient également à

RC200

Hearth & Home Technologies • RC200 Multifunction Remote Control • 2166-392 Rev. C • 1/13

Installation & Operating Instructions

RC200

IntelliFire Plus™ Multifunction Remote Control

Hearth & Home Technologies disclaims any responsibility for,

and the warranty will be voided by, the following actions:

• Installation and use of any damaged system component.

• Modiﬁ cation of the system component.

• Installation other than as instructed by Hearth & Home

Technologies.

• Installation and/or use of any component part not approved

by Hearth & Home Technologies.

Any such action may cause a ﬁ re hazard.

• Read, understand and follow these instructions for safe

installation and operation.

Introduction

The RC200 multifunctional wireless control with dock-

ing station is designed to control constant pilot feature,

ﬂ ame height, blower speed and to turn your gas ﬁ re-

place on and off. The RC200 remote control is only for

use with the Hearth & Home Technologies IntelliFire

Plus™ system (IPI).

FCC Requirements

WARNING! Risk of Fire! Changes or modiﬁ cations to

this unit not expressly approved by the party responsible

for compliance could void the user’s authority to operate

the equipment.

Note: This equipment has been tested and found to

comply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in ac-

cordance with the instructions, may cause harmful in-

terference to radio communications. However, there is

no guarantee that interference will not occur in a partic-

ular installation. If this equipment does cause harmful

interference to radio or television reception, which can

be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit dif-

ferent from that to which the receiver is connected.

• Contact the dealer or an experienced radio TV techni-

cian for help.

Canadian Equipment Requirements

This digital apparatus does not exceed the (Class A/ Class

B) limits for radio noise emissions from digital apparatus

set out in the Radio Interference Regulations of the Cana-

dian Department of Communications. Le present appareil

numerique n’emet pas de bruits radioelectriques depas-

sant les limites applicables aux appareils numeriques (de

la class A/de la class B) prescrites dans le Reglement sur

le brouillage radioelectrique edicte par le ministere des

Communications du Canada.

This device complies with RSS-210 of Industry and Science

Canada. Operation is subject to the following two condi-

tions: (1) this device may not cause interference, and (2)

this device must accept any interference, including interfer-

ence that may cause undesired operation of the device.

Installation Precautions

This control is tested and safe when installed in accor-

dance with this installation manual. Do not install any

components that may be damaged.

Do not modify, disassemble, or substitute any of the com-

ponents included with this kit. Installation of this unit must

be done by a qualiﬁ ed service technician.

Placement of this remote control may affect performance.

An assessment of the space should be done prior to in-

stallation for optimum performance.

Determine Location

Determine the location for the remote control. The selected

location should be in the same space as the gas ﬁ replace

with visual sight of ﬁ replace. The remote control must be

placed within 30 feet of the ﬁ replace but should not be

exposed to extreme heat.

The RC200 is approved for interior installation and should

always be placed under weather resistant cover when used

in exterior applications.

• Keep remote control out of reach of children.

Hearth & Home Technologies • RC200 Multifunction Remote Control • 2166-392 Rev. C • 1/13

Figure 3. Mounting Remote Control Housing

5. Close the housing door and press the power button.

The red light illuminates if the battery was properly in-

stalled. See Figure 3.

Fan Installation

• Insert the 3 prong plug from the fan into the receptacle

located in the AUX200 module. See Figure 5.

Figure 4. AUX 200 module installation

RED LED

AUX200

CABLE

AUX200 Module Installation

• Control Module should be set in the OFF position before

any components are installed.

• Insert the 4 hole harness from the AUX200 module into

the 4 pin plug on the control module. See Figure 4.

Figure 2. Remote in Housing

Installation of Remote Control Housing

CAUTION! Risk of Fire! DO NOT install damaged or

modiﬁ ed components. Warranty will be voided if damaged

or modiﬁ ed components are installed.

Kit components: One remote control, two #6 screws, two

wall anchors, one A23 battery and one AUX200 module (if

purchased retail).

1. Remove remote control components from packaging.

2. Remove battery cover from the back of the remote by

sliding it down and install A23 battery.

To prevent unintended operation when not using your ﬁ re-

place for an extended period of time (summer months,

vacation, trips, etc):

• Remove battery from remote control.

• Unplug switching adapter and remove back-up batteries.

3. Secure the remote control housing on a ﬂ at wall sur-

face using the two screws and wall anchors provided.

See Figure 1.

Figure 1. Mounting Remote Control Housing

4. Place remote control inside housing. See Figure 2.

Hearth & Home Technologies • RC200 Multifunction Remote Control • 2166-392 Rev. C • 1/13

Figure 6. Programming RC200

REMOTE POSITION

Figure 5. Plug Fan into AUX200 Module

Programming the RC200 to the Control Module

CAUTION! Risk of burns! DO NOT program the remote

control to the control module when ﬁ replace is hot.

• Verify the ON/OFF/REMOTE switch is in the REMOTE

position. Green LED light will blink three times and beep

once 5 seconds later when ready. See Figure 6.

• Using a small item (such as a paper clip) press and

release the learn button located near the ON/OFF/

REMOTE switch. See Figure 6.

• Control module will beep once and LED will blink green

for 10 seconds.

• While the LED is blinking, press the power button on

the remote control. A double beep will come out of the

control module to indicate that it has been programmed

successfully.

NOTICE: Up to three remote controls can be programmed

into the control module. Simply press a button on the other

remote controls during the 10 second programming process

to add another remote into the system.

To clear memory in the control module, use a small item

(such as a paper clip) to press and release the LEARN

button. Control module will beep once and LED will blink

green for 10 seconds DO NOT press any buttons on the

remote during the ten seconds that the green LED blinks.

The memory will be cleared.

FAN CORD

• Insert 3 prong plug from AUX200 module into REM/AUX

receptacle of ﬁ replace junction box.

Press the PILOT button to activate or deactivate

the constant pilot.

The control module will beep

once indicating constant pilot has been activat-

ed. A double beep indicates the constant pilot

has been deactivated.

Press the FLAME button to adjust the ﬂ ame

height. The ﬂ ame height can be adjusted to 5

different settings: MAX, HIGH, MEDIUM, LOW,

MIN. Flame height will not be adjustable for ﬁ rst

ten seconds when ﬁ replace is turned on. The

system remembers the previous ﬂ ame height

setting and will automatically adjust to previ-

ous setting after 10 seconds.

Press the FAN button to adjust the fan speed.

The FAN speed can be adjusted to 4 different

settings: HIGH, MED, LOW and OFF. The fan

has a timer built into the control module. After

the ﬁ replace is turned ON the timer will wait for

3 minutes before turning on the fan. In addition,

the fan will remain on for 12 minutes after the

ﬁ replace has been turned OFF. Whenever the

fan is turned ON, the FAN will start up on the

high setting for 10 seconds before adjusting to

the previous user setting.

Function Buttons

Press the POWER button to turn the ﬁ replace

ON and OFF. The ﬁ replace will ﬁ rst ignite the pi-

lot. Once the pilot ﬂ ame is established the main

burner will be lit.

Setting the Child Lock

• Remove battery cover from the back of the remote by

sliding it down. Slide the child lock switch to enable or

disable the child lock feature. See Figure 7.

NOTICE: No functions will be usable until child lock feature

is disabled.

Figure 7. Child Lock Switch

NOTICE: Whenever the ﬁ replace is cycled from OFF to

ON, the main burner will light on high for 10 seconds before

returning to the previous user setting.

Hearth & Home Technologies • RC200 Multifunction Remote Control • 2166-392 Rev. C • 1/13

TO JUNCTION

BOX (120V)

CONTROL MODULE

FLAME

SENSE

WHITE

ORANGE

IGNITER

3 PRONG 120VAC

RC200 12V DC

(A23 X 1)

TO JUNCTION

BOX 120VAC

GROUND

ORANGE

ILOT)

GREEN

(MAIN)

BROWN

BLACK

RED

BROWN/RED

OPTIONAL ON/OFF

SWITCH

BATTERY PACK

6V DC

FLAME

MODULATION

AUX200 MODULE

FAN

6V DC

SUPPLY

Figure 8. RC200 Wiring Diagram

Hearth & Home Technologies • RC200 Multifunction Remote Control • 2166-392 Rev. C • 1/13

Frequently Asked Questions/Troubleshooting

Please contact your Hearth & Home Technologies

dealer with any questions or concerns.

For the location of your nearest

Hearth & Home Technologies dealer,

please visit www.ﬁ reside.com.

Symptom Possible Cause Corrective Action

Remote control will not transmit

Batteries Verify battery is functional and installed correctly.

Remote control is in Child

Lock mode

Disengage Child Lock mode.

Control module will not take

commands from remote control

Control module is not in

“REMOTE” mode

Ensure module switch is set to REMOTE.

Control module and remote

control are not programmed

to each other

The control module will beep when it successfully receives a

command. If it does not beep, clear module memory and re-

program wall switch.

Control module is

unplugged. In case of

power outage, backup

batteries are depleted or

missing

If red LED light comes on when power button is pressed, verify

that the control module is plugged in the ﬁ replace junction box

located in the controls area. Also verify that the batteries are

installed in the battery pack.

Fan does not turn on when ﬁ replace

is started

Built in time delay

The ﬁ replace must run for three minutes in order for the fan to

engage.

Fan does not turn off when ﬁ replace

turned off

Built in time delay The fan will run for twelve minutes after the ﬁ replace is turned off.

Fireplace shuts down after extended

periods

Built-in timer

The ﬁ replace will automatically shut down after nine hours of

continuous operation if it does not receive a command from

the remote.

Fireplace is on but will not shut off

with the remote control

External wired wall switch

The ﬁ replace cannot be turned off by remote if an external

wired wall switch is installed and in the ON position. Turn ex-

ternal wall switch to OFF.

Remote control or control

module failure

At control module, turn off ﬁ replace by sliding the ON/OFF/RE-

MOTE switch to OFF. Warning! Risk of Fire! Fireplace is hot.

Use caution when accessing module.

Power Outage

• If ﬁ replace battery backup system IS installed at time of

power outage, ﬁ replace operation will not be interrupted.

• If ﬁ replace battery backup system IS NOT installed at

time of power outage, ﬁ replace will shut off. To resume

ﬁ replace operation, install battery backup.

NOTICE: Battery polarity must be correct or module

damage will occur.

Manual Fireplace Shutoff

In the unlikely event that the remote wall switch malfunc-

tions and will not turn off the ﬁ replace, call your dealer

for service assistance. In the meantime, you may choose

one of the following actions to turn off the ﬁ replace:

CAUTION! Risk of burns! Fireplace surfaces are hot

when operating and during cool down. Use care and wear

gloves when opening the front and accessing compo-

nents inside the ﬁ replace.

The ﬁ replace may be manually shut down by one of the

following methods:

Turn off the control module:

• Open or remove the decorative front to access the control

module.

• Move switch to OFF (See Figure 6).

Disconnect power to the control module:

• Open or remove the decorative front to access power

cord to the junction box and/or back-up batteries.

• Unplug the control module and/or remove back-up

batteries.

Shut off gas to the control:

• Open or remove the decorative front and locate the gas

shut-off valve to the left of the gas control.

• Rotate the valve 90 degrees to turn off gas supply.

Turn off power to the ﬁ replace (if back-up batteries are

not installed):

• Locate house circuit breaker for ﬁ replace.

• Turn off the circuit breaker.

Hearth and Home Technologies IntelliFire Plus RC200 Manuel utilisateur

Marque: Hearth and Home Technologies

Modèle: IntelliFire Plus RC200

Catégorie: Cheminées

Taper: Manuel utilisateur

Ce manuel convient également à

RC200

Télécharger le PDF

rapport

dans d''autres langues

English: Hearth and Home Technologies IntelliFire Plus RC200 User manual

Hearth and Home Technologies IntelliFire Plus RC200 Manuel utilisateur

Ce manuel convient également à

Hearth and Home Technologies IntelliFire Plus RC200 Manuel utilisateur

dans d''autres langues

Autres documents