Panasonic CU2Z41TBE Mode d'emploi

Deutsch Español Français English

ACXF55-27151

Operating Instructions

Air Conditioner

Model No.

Indoor Unit Outdoor Unit

CS-TZ20WKEW

CS-TZ25WKEW

CS-TZ35WKEW

CS-TZ42WKEW

CS-TZ50WKEW

CS-RZ20WKEW

CS-RZ25WKEW

CS-RZ35WKEW

CS-RZ50WKEW

CS-MTZ16WKE

Single Split

CU-TZ20WKE

CU-TZ25WKE

CU-TZ35WKE

CU-TZ42WKE

CU-TZ50WKE

CU-RZ20WKE

CU-RZ25WKE

CU-RZ35WKE

CU-RZ50WKE

CS-TZ60WKEW

CS-TZ71WKEW

Single Split

CU-TZ60WKE

CU-TZ71WKE

Multi Split

CU-2Z35TBE

CU-2Z41TBE

CU-2Z50TBE

CU-3Z52TBE

CU-3Z68TBE

CU-4Z68TBE

CU-4Z80TBE

CU-5Z90TBE

CU-2TZ41TBE

CU-2TZ50TBE

CU-3TZ52TBE

Operating Instructions

Air Conditioner

2-25

Before operating the unit, please read these operating

instructions thoroughly and keep them for future reference.

The included Installation Instructions should be kept and read

by the installer before installation.

Remote control is packaged in the indoor unit and removed

by the installer before installation.

Comment utiliser l’appareil

Climatiseur

26-49

Avant d’utiliser l’appareil, veuillez lire ce mode d’emploi dans

son intégralité et conservez-le pour toute référence ultérieure.

Le manuel d’installation inclus doit être conservé et lu par

l’installateur avant l’installation.

La télécommande est emballée dans l’unité intérieure et

retirée par l’installateur avant l’installation.

Instrucciones de funcionamiento

Climatizador de aire

50-73

Antes de utilizar la unidad, sírvase leer atentamente estas

instrucciones de funcionamiento y conservarlas para futuras

consultas.

El instalador debe guardar y leer las Instrucciones de

instalación incluidas antes de la instalación.

El mando a distancia viene embalado en la unidad interior y

debe ser retirado por el instalador antes de la instalación.

Bedienungsanleitung

Klimagerät

74-97

Bevor Sie das Gerät in Betrieb nehmen, lesen Sie bitte diese

Bedienungsanleitung aufmerksam durch und bewahren Sie

sie als künftige Referenz auf.

Das mitgelieferte Installationshandbuch sollte aufbewahrt und

vor der Installation vom Installateur gelesen werden.

Die Fernbedienung ist im Innengerät verpackt und wird vor

der Installation durch den Installateur entfernt.

ACXF55-27151.indb 1ACXF55-27151.indb 1 12/2/2019 10:07:38 AM12/2/2019 10:07:38 AM

2

A new built-in Network Adaptor that allows you to control your

heatpump from everywhere.

Use remote

control within 8 m

from the remote

control receiver of

the indoor unit.

Quick Guide

* Remote control display

and functions may

vary depending on the

model.

Flexibility to connect

Single Split System or

Multi Split System Air

Conditioner to suit your

needs.

For complete product features,

please refer to catalogue.

Inserting the batteries

1

2

3

1

Pull out the back cover

of remote control.

2

Insert AAA or R03

batteries.

3

Close the cover.

A

Clock setting

1

Press

CLOCK

and

set

the time

.

• Press

CLOCK

and hold for

approximately 5

seconds to show

time in 12-hour

(am/pm) or 24 hour

indication.

2

Conﬁ rm

SET

.

B

TIMER

OFF

TIMER

ON

FAN SPEED/

QUIET

B

A

ACXF55-27151.indb 2ACXF55-27151.indb 2 12/2/2019 10:07:39 AM12/2/2019 10:07:39 AM

3

English

Table of contents

Safety precautions

………

4-15

How to use

……………………

16-17

To learn more

……………

18-19

Cleaning instructions

………

20

Troubleshooting

…………

21-23

Information…………… 24-25

Accessories

• Remote control

• AAA or R03 batteries × 2

• Remote control holder

• Screws for remote control

holder × 2

The illustrations in this manual are for

explanation purposes only and may differ

from the actual unit. They are subject

to change without notice for future

improvement.

B

Basic operation

Thank you for purchasing

Panasonic Air Conditioner.

1

Press

to start/stop the

operation.

POWER

• Please note that

the

indication

is on display to

start the unit.

3

Select the desired

temperature.

Up

Down

Selection range:

16.0 °C ~ 30.0 °C /

60 °F ~ 86 °F.

• Press and hold

for

approximately 10 seconds

to switch the temperature

indication in °C or °F.

2

Press

to

select the desired

mode.

DRY

AUTO HEAT

COOL

ACXF55-27151.indb 3ACXF55-27151.indb 3 12/2/2019 10:07:40 AM12/2/2019 10:07:40 AM

4

Safety precautions

To prevent personal injury, injury to others

or property damage, please comply with the

following:

Incorrect operation due to failure to follow

instructions below may cause harm or

damage, the seriousness of which is

classiﬁ ed as below:

This appliances is not intended for

accessibility by the general public.

WARNING

This sign

warns of

death or

serious injury.

CAUTION

This sign

warns of

injury or

damage to

property.

The instructions to be followed are classiﬁ ed

by the following symbols:

This symbol denotes an

action that is PROHIBITED.

These symbols denote

actions COMPULSORY.

WARNING

Indoor unit and outdoor unit

This appliance can be used by

children aged from 8 years and above

and persons with reduced physical,

sensory or mental capabilities or

lack of experience and knowledge

if they have been given supervision

or instruction concerning use of

the appliance in a safe way and

understand the hazards involved.

Children shall not play with the

appliance. Cleaning and user

maintenance shall not be made by

children without supervision.

Please consult authorised dealer or

specialist to clean the internal parts,

repair, install, remove, disassemble

and reinstall the unit. Improper

installation and handling will cause

leakage, electric shock or ﬁ re.

Conﬁ rm with authorised dealer or

specialist on usage of any speciﬁ ed

refrigerant type. Using refrigerant

type other than the speciﬁ ed may

cause product damage, burst and

injury etc.

Do not use means to accelerate

the defrosting process or to clean,

other than those recommended by

manufacturer.

Any unﬁ t method or using

incompatible material may cause

product damage, burst and serious

injury.

Do not install the unit in a potentially

explosive or ﬂ ammable atmosphere.

Failure to do so could result in ﬁ re.

Indoor unit

Outdoor unit

Power supply

Remote control

Air inlet

Air outlet

ACXF55-27151.indb 4ACXF55-27151.indb 4 12/2/2019 10:07:41 AM12/2/2019 10:07:41 AM

5

English

Do not insert your ﬁ ngers

or other objects into the air

conditioner indoor or outdoor

unit, rotating parts may cause

injury.

Do not touch the outdoor unit during

lightning, it may cause electric shock.

Do not expose yourself directly to

cold air for a long period to avoid

excess cooling.

Do not sit or step on the unit,

you may fall down accidentally.

Remote control

Do not allow infants and small

children to play with the remote

control to prevent them from

accidentally swallowing the batteries.

Power supply

Do not use a modiﬁ ed

cord, joint cord,

extension cord or

unspeciﬁ ed cord to

prevent overheating and

ﬁ re.

To prevent overheating, ﬁ re or electric

shock:

•

Do not share the same power outlet

with other equipment.

•

Do not operate with wet hands.

•

Do not over bend the power supply

cord.

•

Do not operate or stop the unit by

inserting or pulling out the power

plug.

If the supply cord is damaged, it must

be replaced by the manufacturer,

service agent or similarly qualiﬁ ed

persons in order to avoid a hazard.

It is strongly recommended to be

installed with Earth Leakage Circuit

Breaker (ELCB) or Residual Current

Device (RCD) to prevent electric

shock or ﬁ re.

To prevent overheating, ﬁ re or electric

shock:

•

Insert the power plug properly.

•

Dust on the power plug should be

periodically wiped with a dry cloth.

Stop using the product if any

abnormality/failure occurs and

disconnect the power plug or turn off

the power switch and breaker.

(Risk of smoke/ﬁ re/electric shock)

Examples of abnormality/failure

•

The ELCB trips frequently.

•

Burning smell is observed.

•

Abnormal noise or vibration of the

unit is observed.

•

Water leaks from the indoor unit.

•

Power cord or plug becomes

abnormally hot.

•

Fan speed cannot be controlled.

•

The unit stops running immediately

even if it is switched on for

operation.

•

The fan does not stop even if the

operation is stopped.

Contact your local dealer immediately

for maintenance/repair.

This equipment must be earthed to

prevent electrical shock or ﬁ re.

Prevent electric shock by switching

off the power supply and unplug:

-Before cleaning or servicing,

-When extended non-use, or

-During abnormally strong lightning

activity.

Safety precautions

ACXF55-27151.indb 5ACXF55-27151.indb 5 12/2/2019 10:07:41 AM12/2/2019 10:07:41 AM

6

Safety precautions

CAUTION

Indoor unit and outdoor unit

Do not wash the indoor unit with

water, benzine, thinner or scouring

powder to avoid damage or corrosion

at the unit.

Do not use for preservation of precise

equipment, food, animals, plants,

artwork or other objects. This may

cause quality deterioration, etc.

Do not use any combustible

equipment in front of the airﬂ ow outlet

to avoid ﬁ re propagation.

Do not expose plants or pet directly

to airﬂ ow to avoid injury, etc.

Do not touch the sharp

aluminium ﬁ n, sharp parts may

cause injury.

Do not switch ON the indoor unit

when waxing the ﬂ oor. After waxing,

aerate the room properly before

operating the unit.

Do not install the unit in oily and

smoky areas to prevent damage to

the unit.

Do not dismantle the unit for cleaning

purpose to avoid injury.

Do not step onto an unstable bench

when cleaning the unit to avoid injury.

Do not place a vase or water

container on the unit. Water may

enter the unit and degrade the

insulation. This may cause an electric

shock.

Do not open window or door for

long time during operation, it may

lead to inefﬁ cient power usage and

uncomfortable temperature changes.

Prevent water leakage by ensuring

drainage pipe is:

- Connected properly,

- Kept clear of gutters and containers,

or

- Not immersed in water

After a long period of use or use with

any combustible equipment, aerate

the room regularly.

After a long period of use, make

sure the installation rack does not

deteriorate to prevent the unit from

falling down.

Remote control

Do not use rechargeable (Ni-Cd)

batteries. It may damage the remote

control.

To prevent malfunction or damage of

the remote control:

•

Remove the batteries if the unit

is not going to be used for a long

period of time.

•

New batteries of the same type must

be inserted following the polarity

stated.

Power supply

Do not disconnect the plug by pulling

the cord to prevent electric shock.

ACXF55-27151.indb 6ACXF55-27151.indb 6 12/2/2019 10:07:41 AM12/2/2019 10:07:41 AM

7

English

WARNING

This appliance is ﬁ lled with

R32

(mild ﬂ ammable refrigerant).

If the refrigerant is leaked and

exposed to an external ignition

source, there is a risk of ﬁ re.

Indoor unit and outdoor unit

The appliance shall be installed, and/

or operated in a room with ﬂ oor area

larger than Amin (m²) and keep away

from ignition sources, such as heat/

sparks/open ﬂ ame or hazardous

areas such as gas appliances,

gas cooking, reticulated gas

supply systems or electric cooking

appliances, etc.(Refer to Table A of

Installation instructions table for Amin

(m²))

Be aware that refrigerant may

not contain an odour, highly

recommended to ensure suitable

ﬂ ammable refrigerant gas detectors

are present, operating and able to

warn of a leak.

Keep any required ventilation

openings clear of obstruction.

Do not pierce or burn as the

appliance is pressurized. Do not

expose the appliance to heat, ﬂ ame,

sparks, or other sources of ignition.

Else it may explode and cause injury

or death.

Precaution for using R32

refrigerant

The basic installation work procedures are

the same as conventional refrigerant (R410A,

R22) models.

Since the working pressure is

higher than that of refrigerant R22

models, some of the piping and

installation and service tools are

special. Especially, when replacing

a refrigerant R22 model with a

new refrigerant R32 model, always

replace the conventional piping and

ﬂ are nuts with the R32 and R410A

piping and ﬂ are nuts on the outdoor

unit side.

For R32 and R410A, the same ﬂ are

nut on the outdoor unit side and pipe

can be used.

The mixing of different refrigerants

within a system is prohibited. Models

that use refrigerant R32 and R410A

have a different charging port thread

diameter to prevent erroneous

charging with refrigerant R22 and for

safety.

Therefore, check beforehand. [The

charging port thread diameter for R32

and R410A is 1/2 inch.]

Must always ensure that foreign

matter (oil, water, etc.) does not enter

the piping. Also, when storing the

piping, securely seal the opening by

pinching, taping, etc. (Handling of

R32 is similar to R410A.)

•

Operation, maintenance, repairing

and refrigerant recovery should be

carried out by trained and certiﬁ ed

personnel in the use of ﬂ ammable

refrigerants and as recommended

by the manufacturer. Any personnel

conducting an operation, servicing

or maintenance on a system or

associated parts of the equipment

should be trained and certiﬁ ed.

Safety precautions

ACXF55-27151.indb 7ACXF55-27151.indb 7 12/2/2019 10:07:41 AM12/2/2019 10:07:41 AM

8

•

Any part of refrigerating circuit

(evaporators, air coolers, AHU,

condensers or liquid receivers) or

piping should not be located in the

proximity of heat sources, open

ﬂ ames, operating gas appliance or

an operating electric heater.

•

The user/owner or their authorised

representative shall regularly check

the alarms, mechanical ventilation

and detectors, at least once a

year, where as required by national

regulations, to ensure their correct

functioning.

•

A logbook shall be maintained. The

results of these checks shall be

recorded in the logbook.

•

In case of ventilations in occupied

spaces shall be checked to conﬁ rm

no obstruction.

•

Before a new refrigerating system

is put into service, the person

responsible for placing the system

in operation should ensure that

trained and certiﬁ ed operating

personnel are instructed on the

basis of the instruction manual

about the construction, supervision,

operation and maintenance of the

refrigerating system, as well as the

safety measures to be observed,

and the properties and handling of

the refrigerant used.

•

The general requirement of trained

and certiﬁ ed personnel are indicated

as below:

a) Knowledge of legislation,

regulations and standards

relating to ﬂ ammable

refrigerants; and,

b) Detailed knowledge of and

skills in handling ﬂ ammable

refrigerants, personal protective

equipment, refrigerant leakage

prevention, handling of cylinders,

charging, leak detection,

recovery and disposal; and,

c) Able to understand and to apply

in practice the requirements

in the national legislation,

regulations and Standards; and,

d) Continuously undergo regular

and further training to maintain

this expertise.

e) Air-conditioner piping in the

occupied space shall be installed

in such a way to protect against

accidental damage in operation

and service.

f) Precautions shall be taken to

avoid excessive vibration or

pulsation to refrigerating piping.

g) Ensure protection devices,

refrigerating piping and ﬁ ttings

are well protected against

adverse environmental effects

(such as the danger of water

collecting and freezing in relief

pipes or the accumulation of dirt

and debris).

h) Expansion and contraction of

long runs piping in refrigerating

systems shall be designed and

installed securely (mounted

and guarded) to minimize the

likelihood hydraulic shock

damaging the system.

i) Protect the refrigerating

system from accidental rupture

due to moving furniture or

reconstruction activities.

j) To ensure no leaking, ﬁ eld-made

refrigerant joints indoors shall

be tightness tested. The test

method shall have a sensitivity

of 5 grams per year of refrigerant

or better under a pressure of at

least 0.25 times the maximum

allowable pressure (>1.04 MPa,

max 4.15 MPa). No leak shall be

detected.

Safety precautions

ACXF55-27151.indb 8ACXF55-27151.indb 8 12/2/2019 10:07:41 AM12/2/2019 10:07:41 AM

9

English

1. Installation (Space)

•

Product with ﬂ ammable refrigerants,

shall be installed according to

the minimum room area, Amin

(m²) mentioned in Table A of the

Installation Instructions.

•

In case of ﬁ eld charge, the effect

on refrigerant charge caused by

the different pipe length has to be

quantiﬁ ed, measured and labelled.

•

Must ensure the installation of pipe-

work shall be kept to a minimum.

Avoid use dented pipe and do not

allow acute bending.

•

Must ensure that pipe-work shall be

protected from physical damage.

•

Must comply with national gas

regulations, state municipal rules

and legislation. Notify relevant

authorities in accordance with all

applicable regulations.

•

Must ensure mechanical

connections be accessible for

maintenance purposes.

•

In cases that require mechanical

ventilation, ventilation openings shall

be kept clear of obstruction.

•

When disposal of the product, do

follow to the precautions in #12 and

comply with national regulations.

Always contact to local municipal

ofﬁ ces for proper handling.

2. Servicing

2-1. Service personnel

•

The system is inspected, regularly

supervised and maintained by

a trained and certiﬁ ed service

personnel who is employed by the

person user or party responsible.

•

Ensure the actual refrigerant charge

is in accordance with the room

size within which the refrigerant

containing parts are installed.

•

Ensure refrigerant charge not to

leak.

•

Any qualiﬁ ed person who is involved

with working on or breaking into

a refrigerant circuit should hold

a current valid certiﬁ cate from an

industry-accredited assessment

authority, which authorizes their

competence to handle refrigerants

safely in accordance with an

industry recognised assessment

speciﬁ cation.

•

Servicing shall only be performed

as recommended by the equipment

manufacturer. Maintenance and

repair requiring the assistance of

other skilled personnel shall be

carried out under the supervision of

the person competent in the use of

ﬂ ammable refrigerants.

•

Servicing shall be performed only as

recommended by the manufacturer.

Safety precautions

ACXF55-27151.indb 9ACXF55-27151.indb 9 12/2/2019 10:07:41 AM12/2/2019 10:07:41 AM

10

Safety precautions

2-2. Work

•

Prior to beginning work on systems

containing ﬂ ammable refrigerants,

safety checks are necessary to

ensure that the risk of ignition

is minimised.

For repair to the

refrigerating system, the precautions in

#2-2 to #2-8 must be followed before

conducting work on the system.

•

Work shall be undertaken under

a controlled procedure so as to

minimize the risk of a ﬂ ammable gas

or vapour being present while the

work is being performed.

•

All maintenance staff and others

working in the local area shall be

instructed and supervised on the

nature of work being carried out.

•

Avoid working in conﬁ ned spaces.

Always ensure away from source, at

least 2 meter of safety distance, or

zoning of free space area of at least

2 meter in radius.

•

Wear appropriate protective

equipment, including respiratory

protection, as conditions warrant.

•

Keep all sources of ignition and hot

metal surfaces away.

2-3. Checking for presence of

refrigerant

•

The area shall be checked with an

appropriate refrigerant detector prior

to and during work, to ensure the

technician is aware of potentially

ﬂ ammable atmospheres.

•

Ensure that the leak detection

equipment being used is suitable for

use with ﬂ ammable refrigerants, i.e.

non sparking, adequately sealed or

intrinsically safe.

•

In case of leakage/spillage

happened, immediately ventilate

area and stay upwind and away

from spill/release.

•

In case of leakage/spillage

happened, do notify persons down

wind of the leaking/spill, isolate

immediate hazard area and keep

unauthorized personnel out.

2-4. Presence of ﬁ re extinguisher

•

If any hot work is to be conducted

on the refrigerating equipment or

any associated parts, appropriate

ﬁ re extinguishing equipment shall be

available at hand.

•

Have a dry powder or CO

2

ﬁ re

extinguisher adjacent to the

charging area.

2-5. No ignition sources

•

No person carrying out work in

relation to a refrigerating system

which involves exposing any pipe

work that contains or has contained

ﬂ ammable refrigerant shall use any

sources of ignition in such a manner

that it may lead to the risk of ﬁ re

or explosion. He/She must not be

smoking when carrying out such

work.

•

All possible ignition sources,

including cigarette smoking, should

be kept sufﬁ ciently far away from

the site of installation, repairing,

removing and disposal, during which

ﬂ ammable refrigerant can possibly

be released to the surrounding

space.

•

Prior to work taking place, the area

around the equipment is to be

surveyed to make sure that there

are no ﬂ ammable hazards or ignition

risks.

•

“No Smoking” signs shall be

displayed.

2-6. Ventilated area

•

Ensure that the area is in the open

or that it is adequately ventilated

before breaking into the system or

conducting any hot work.

•

A degree of ventilation shall continue

during the period that the work is

carried out.

•

The ventilation should safely

disperse any released refrigerant

and preferably expel it externally

into the atmosphere.

ACXF55-27151.indb 10ACXF55-27151.indb 10 12/2/2019 10:07:41 AM12/2/2019 10:07:41 AM

11

English

2-7. Checks to the refrigerating

equipment

•

Where electrical components are

being changed, they shall be ﬁ t

for the purpose and to the correct

speciﬁ cation.

•

At all times the manufacturer’s

maintenance and service guidelines

shall be followed.

•

If in doubt consult the

manufacturer’s technical department

for assistance.

•

The following checks shall be

applied to installations using

ﬂ ammable refrigerants.

-

The actual refrigerant charge

is in accordance with the room

size within which the refrigerant

containing parts are installed.

-

The ventilation machinery and

outlets are operating adequately

and are not obstructed.

-

If an indirect refrigerating circuit is

being used, the secondary circuit

shall be checked for the presence

of refrigerant.

-

Marking to the equipment

continues to be visible and legible.

Markings and signs that are

illegible shall be corrected.

-

Refrigerating pipe or components

are installed in a position where

they are unlikely to be exposed to

any substance which may corrode

refrigerant containing components,

unless the components are

constructed of materials which

are inherently resistant to being

corroded or are properly protected

against being so corroded.

2-8. Checks to electrical devices

•

Repair and maintenance to electrical

components shall include initial

safety checks and component

inspection procedures.

•

Initial safety checks shall include but

not limit to:-

-

That capacitors are discharged:

this shall be done in a safe

manner to avoid possibility of

sparking.

-

That there no live electrical

components and wiring are

exposed while charging,

recovering or purging the system.

-

That there is continuity of earth

bonding.

•

At all times the manufacturer’s

maintenance and service guidelines

shall be followed.

•

If in doubt consult the

manufacturer’s technical department

for assistance.

•

If a fault exists that could

compromise safety, then no

electrical supply shall be connected

to the circuit until it is satisfactorily

dealt with.

•

If the fault cannot be corrected

immediately but it is necessary to

continue operation, an adequate

temporary solution shall be used.

•

The owner of the equipment must be

informed or reported so all parties

are advised thereinafter.

Safety precautions

ACXF55-27151.indb 11ACXF55-27151.indb 11 12/2/2019 10:07:41 AM12/2/2019 10:07:41 AM

12

Safety precautions

3. Repairs to sealed components

•

During repairs to sealed

components, all electrical supplies

shall be disconnected from the

equipment being worked upon prior

to any removal of sealed covers, etc.

•

If it is absolutely necessary to have

an electrical supply to equipment

during servicing, then a permanently

operating form of leak detection

shall be located at the most critical

point to warn of a potentially

hazardous situation.

•

Particular attention shall be paid

to the following to ensure that by

working on electrical components,

the casing is not altered in such a

way that the level of protection is

affected.This shall include damage

to cables, excessive number of

connections, terminals not made

to original speciﬁ cation, damage to

seals, incorrect ﬁ tting of glands, etc.

•

Ensure that apparatus is mounted

securely.

•

Ensure that seals or sealing

materials have not degraded

such that they no longer serve the

purpose of preventing the ingress of

ﬂ ammable atmospheres.

•

Replacement parts shall be in

accordance with the manufacturer’s

speciﬁ cations.

NOTE: The use of silicon sealant

may inhibit the effectiveness of some

types of leak detection equipment.

Intrinsically safe components do not

have to be isolated prior to working

on them.

4. Repair to intrinsically safe

components

•

Do not apply any permanent

inductive or capacitance loads to

the circuit without ensuring that

this will not exceed the permissible

voltage and current permitted for the

equipment in use.

•

Intrinsically safe components are

the only types that can be worked

on while live in the presence of a

ﬂ ammable atmosphere.

•

The test apparatus shall be at the

correct rating.

•

Replace components only with

parts speciﬁ ed by the manufacturer.

Unspeciﬁ ed parts by manufacturer

may result ignition of refrigerant in

the atmosphere from a leak.

5. Cabling

•

Check that cabling will not be

subject to wear, corrosion, excessive

pressure, vibration, sharp edges or

any other adverse environmental

effects.

•

The check shall also take into

account the effects of aging or

continual vibration from sources

such as compressors or fans.

6. Detection of ﬂ ammable

refrigerants

•

Under no circumstances shall

potential sources of ignition be used

in the searching or detection of

refrigerant leaks.

•

A halide torch (or any other detector

using a naked ﬂ ame) shall not be

used.

ACXF55-27151.indb 12ACXF55-27151.indb 12 12/2/2019 10:07:41 AM12/2/2019 10:07:41 AM

13

English

7. The following leak detection

methods are deemed

acceptable for all refrigerant

systems

•

No leaks shall be detected when

using detection equipment with

a sensitivity of 5 grams per year

of refrigerant or better under a

pressure of at least 0.25 times the

maximum allowable pressure

(>1.04 MPa, max 4.15 MPa), for

example, a universal sniffer.

•

Electronic leak detectors may

be used to detect ﬂ ammable

refrigerants, but the sensitivity may

not be adequate, or may need re-

calibration.

(Detection equipment shall be

calibrated in a refrigerant-free area.)

•

Ensure that the detector is not a

potential source of ignition and is

suitable for the refrigerant used.

•

Leak detection equipment shall be

set at a percentage of the LFL of the

refrigerant and shall be calibrated

to the refrigerant employed and the

appropriate percentage of gas (25 %

maximum) is conﬁ rmed.

•

Leak detection ﬂ uids are also

suitable for use with most

refrigerants, for example, bubble

method and ﬂ uorescent method

agents. The use of detergents

containing chlorine shall be avoided

as the chlorine may react with the

refrigerant and corrode the copper

pipe-work.

•

If a leak is suspected, all naked

ﬂ ames shall be removed/

extinguished.

•

If a leakage of refrigerant is found

which requires brazing, all of the

refrigerant shall be recovered from

the system, or isolated (by means

of shut off valves) in a part of the

system remote from the leak. The

precautions in #8 must be followed

to remove the refrigerant.

8. Removal and evacuation

•

When breaking into the refrigerant

circuit to make repairs – or for

any other purpose – conventional

procedures shall be used. However,

it is important that best practice

is followed since ﬂ ammability is

a consideration. The following

procedure shall be adhered to:

remove refrigerant -> purge the

circuit with inert gas -> evacuate

-> purge with inert gas -> open the

circuit by cutting or brazing.

•

The refrigerant charge shall be

recovered into the correct recovery

cylinders.

•

The system shall be purged with

OFN to render the appliance safe.

•

This process may need to be

repeated several times.

•

Compressed air or oxygen shall not

be used for this task.

•

Purging shall be achieved by

breaking the vacuum in the system

with OFN and continuing to ﬁ ll until

the working pressure is achieved,

then venting to atmosphere, and

ﬁ nally pulling down to a vacuum.

•

This process shall be repeated until

no refrigerant is within the system.

•

When the ﬁ nal OFN charge is used,

the system shall be vented down

to atmospheric pressure to enable

work to take place.

•

This operation is absolutely vital if

brazing operations on the pipe work

are to take place.

•

Ensure that the outlet for the

vacuum pump is not close to any

potential ignition sources and there

is ventilation available.

OFN = oxygen free nitrogen,

type of inert gas.

Safety precautions

ACXF55-27151.indb 13ACXF55-27151.indb 13 12/2/2019 10:07:41 AM12/2/2019 10:07:41 AM

14

Safety precautions

9. Charging procedures

•

In addition to conventional

charging procedures, the following

requirements shall be followed.

-

Ensure that contamination of

different refrigerants does not

occur when using charging

equipment.

-

Hoses or lines shall be as short as

possible to minimize the amount of

refrigerant contained in them.

-

Cylinders shall be kept in an

appropriate position according to

the instructions.

-

Ensure that the refrigerating

system is earthed prior to charging

the system with refrigerant.

-

Label the system when charging is

complete (if not already).

-

Extreme care shall be taken not to

over ﬁ ll the refrigerating system.

•

Prior to recharging the system it

shall be pressure tested with OFN

(refer to #7).

•

The system shall be leak tested on

completion of charging but prior to

commissioning.

•

A follow up leak test shall be carried

out prior to leaving the site.

•

Electrostatic charge may

accumulate and create a hazardous

condition when charging and

discharging the refrigerant.To

avoid ﬁ re or explosion, dissipate

static electricity during transfer by

grounding and bonding containers

and equipment before charging/

discharging.

10. Decommissioning

•

Before carrying out this procedure,

it is essential that the technician

is completely familiar with the

equipment and all its details.

•

It is recommended good practice

that all refrigerants are recovered

safely.

•

Prior to the task being carried

out, an oil and refrigerant sample

shall be taken in case analysis is

required prior to re-use of recovered

refrigerant.

•

It is essential that electrical power

is available before the task is

commenced.

a) Become familiar with the

equipment and its operation.

b) Isolate system electrically.

c) Before attempting the procedure

ensure that:

•

mechanical handling equipment is

available, if required, for handling

refrigerant cylinders;

•

all personal protective equipment

is available and being used

correctly;

•

the recovery process is

supervised at all times by a

competent person;

•

recovery equipment and cylinders

conform to the appropriate

standards.

d) Pump down refrigerant system, if

possible.

e) If a vacuum is not possible, make

a manifold so that refrigerant can

be removed from various parts of

the system.

f) Make sure that cylinder is

situated on the scales before

recovery takes place.

g) Start the recovery machine and

operate in accordance with

instructions.

h) Do not over ﬁ ll cylinders. (No

more than 80 % volume liquid

charge).

ACXF55-27151.indb 14ACXF55-27151.indb 14 12/2/2019 10:07:41 AM12/2/2019 10:07:41 AM

15

English

i) Do not exceed the maximum

working pressure of the cylinder,

even temporarily.

j) When the cylinders have been

ﬁ lled correctly and the process

completed, make sure that the

cylinders and the equipment

are removed from site promptly

and all isolation valves on the

equipment are closed off.

k) Recovered refrigerant shall not be

charged into another refrigerating

system unless it has been

cleaned and checked.

•

Electrostatic charge may accumulate

and create a hazardous condition

when charging or discharging the

refrigerant.To avoid ﬁ re or explosion,

dissipate static electricity during

transfer by grounding and bonding

containers and equipment before

charging/discharging.

11. Labelling

•

Equipment shall be labelled stating

that it has been de-commissioned

and emptied of refrigerant.

•

The label shall be dated and signed.

•

Ensure that there are labels on the

equipment stating the equipment

contains ﬂ ammable refrigerant.

12. Recovery

•

When removing refrigerant from

a system, either for servicing

or decommissioning, it is

recommended good practice that all

refrigerants are removed safely.

•

When transferring refrigerant

into cylinders, ensure that only

appropriate refrigerant recovery

cylinders are employed.

•

Ensure that the correct number of

cylinders for holding the total system

charge are available.

•

All cylinders to be used are

designated for the recovered

refrigerant and labelled for that

refrigerant (i.e. special cylinders for

the recovery of refrigerant).

•

Cylinders shall be complete

with pressure relief valve and

associated shut-off valves in good

working order.

•

Recovery cylinders are evacuated

and, if possible, cooled before

recovery occurs.

•

The recovery equipment shall

be in good working order with a

set of instructions concerning the

equipment that is at hand and

shall be suitable for the recovery of

ﬂ ammable refrigerants.

•

In addition, a set of calibrated

weighing scales shall be available

and in good working order.

•

Hoses shall be complete with leak-

free disconnect couplings and in

good condition.

•

Before using the recovery machine,

check that it is in satisfactory

working order, has been properly

maintained and that any associated

electrical components are sealed

to prevent ignition in the event

of a refrigerant release.Consult

manufacturer if in doubt.

•

The recovered refrigerant shall be

returned to the refrigerant supplier

in the correct recovery cylinder, and

the relevant Waste Transfer Note

arranged.

•

Do not mix refrigerants in recovery

units and especially not in cylinders.

•

If compressors or compressor oils

are to be removed, ensure that

they have been evacuated to an

acceptable level to make certain

that ﬂ ammable refrigerant does not

remain within the lubricant.

•

The evacuation process shall be

carried out prior to returning the

compressor to the suppliers.

•

Only electric heating to the

compressor body shall be

employed to accelerate this

process.

•

When oil is drained from a system,

it shall be carried out safely.

Safety precautions

ACXF55-27151.indb 15ACXF55-27151.indb 15 12/2/2019 10:07:41 AM12/2/2019 10:07:41 AM

16

How to use

Indicator

To adjust airﬂ ow direction To adjust airﬂ ow direction

AIR SWING

Upper direction

Lateral direction

(CS-TZ60/71WKEW)

• Do not adjust the ﬂ ap by hand.

POWER

TIMER

• This operation stops automatically after 20 minutes.

To reach set temperature quickly

POWERFUL

FAN SPEED:

• For AUTO, the indoor fan speed is automatically

adjusted according to the operation mode.

QUIET:

• This operation reduces airﬂ ow noise.

To adjust FAN SPEED and QUIET condition

FAN SPEED/

AUTO

FAN

QUIET

To adjust airﬂ ow directionTo adjust airﬂ ow direction

AIR SWING

Upper direction

( CS-TZ20/25/35/42/50WKEW,

CS-RZ20/25/35/50WKEW, CS-MTZ16WKE)

Upper direction:

• Do not adjust the ﬂ ap by hand.

Lateral

direction

Lateral direction:

• For lateral direction, it is

manually adjustable as

shown.

CS-TZ60/71WKEW

TIMER

OFF

TIMER

ON

FAN SPEED/

QUIET

Not used

in normal

operations.

Press to restore

the remote

control to default

setting.

CS-TZ20/25/35/42/50WKEW

CS-RZ20/25/35/50WKEW

CS-MTZ16WKE

Press to

ON/ OFF

Wireless

LAN

features.

TIMER

FAN SPEED/

QUIET

ACXF55-27151.indb 16ACXF55-27151.indb 16 12/2/2019 10:07:41 AM12/2/2019 10:07:41 AM

17

English

See "To learn more..." for details.

How to use

To set the timer

• To cancel ON or OFF timer, press

TIMER

ON

or

TIMER

OFF

to select respective or then

press

CANCEL

.

• If timer is cancelled manually or due to

power failure, you can restore the timer

again by pressing

TIMER

ON

or

TIMER

OFF

to select

respective

or then press

SET

.

• The nearest timer setting will be displayed

and will activate in sequence.

• Timer operation is based on the clock set

in the remote control and repeats daily

once set. For clock setting, please refer to

Quick Guide.

2 sets of ON and OFF timers are available to turn ON or OFF the unit at different preset time.

TIMER

OFF

TIMER

ON

3

1

2

Select ON or OFF

timer

Example:

OFF at 22:00

• Each time pressed:

(exit setting)

TIMER

OFF

Set the time

Conﬁ rm

2

SET

1

2

3

Note

SLEEP

,

POWERFUL POWERFUL

,

FAN SPEED/

• Can be selected at the same time.

• Can be activated in all modes.

• Can be cancelled by pressing the

respective button again.

• POWERFUL, QUIET and FAN SPEED

cannot be selected at the same time.

To maximise comfort while sleeping

• This operation provides you with a comfortable environment while sleeping. It will

automatically adjust the sleep pattern temperature during the activation period.

• The indoor unit indicator will dim when this operation is activated. This is not applicable if

the indicator brightness has been manually dimmed.

• This operation is incorporated with the activation timer (0.5, 1, 2, 3, 4, 5, 6, 7, 8 or 9 hours).

• This operation can be set together with timer. Sleep operation has the priority over OFF

timer.

• This operation can be cancelled by pressing the respective button until the sleep timer

reaches 0.0h.

SLEEP

• For Wireless LAN Module operation setup, please refer to Setup Instructions

Manual.

App InstallationTo connect network

ACXF55-27151.indb 17ACXF55-27151.indb 17 12/2/2019 10:07:43 AM12/2/2019 10:07:43 AM

18

Energy saving temperature setting

Operating the unit within the recommended temperature range may save energy.

HEAT : 20.0 °C ~ 24.0 °C / 68 °F ~ 75 °F.

COOL: 26.0 °C ~ 28.0 °C / 79 °F ~ 82 °F.

Air ﬂ ow direction

In COOL/DRY mode:

If AUTO is set, the ﬂ ap swings up/down or left/right (subject to feature applicability)

automatically.

In HEAT mode:

If AUTO is set, the horizontal ﬂ ap is ﬁ xed at the predetermined position. The vertical ﬂ ap

(subject to feature applicability) swings left/right after the temperature rises.

Auto restart control

If power is resumed after a power failure, the operation will restart automatically after a

period of time with previous operation mode and airﬂ ow direction.

• This control is not applicable when TIMER is set.

To learn more...

Single

Single split system

Multi

Multi split system

Operation mode

• It is possible to operate the indoor units individually or simultaneously. The priority of

operation is placed on the ﬁ rst unit that turned on.

• During operation, HEAT and COOL modes cannot activate at the same time for different

indoor units.

• The power indicator blinks to indicate the indoor unit is standing by for different operation

mode.

AUTO : During operation, the POWER indicator will blinks at initial.

Single

• Unit selects operation mode every 10 minutes according to the setting and room

temperatures.

Multi

• Unit selects operation mode every 3 hours according to setting temperature,

outdoor temperature and room temperature.

HEAT : The POWER indicator blinks at the initial stage of this operation. Unit takes a while

to warm up.

• For system which HEAT mode has been locked, if operation mode other than

HEAT is selected, the indoor unit stops and the POWER indicator blinks.

COOL : Provides efﬁ cient comfort cooling to suit your needs.

DRY : Unit operates at low fan speed to give a gentle cooling operation.

ACXF55-27151.indb 18ACXF55-27151.indb 18 12/2/2019 10:07:43 AM12/2/2019 10:07:43 AM

19

English

Operating conditions

Use this air conditioner in the temperature range indicated in the table.

Temperature

°C (°F)

Indoor

Single split outdoor unit

*

1

Multi split outdoor unit *

2

DBT WBT DBT WBT DBT WBT

COOL

Max. 32 (89.6) 23 (73.4) 43 (109.4) 26 (78.8) 46 (114.8) 26 (78.8)

Min. 16 (60.8) 11 (51.8) -10 (14.0) - -10 (14.0) -

HEAT

Max. 30 (86.0) - 24 (75.2) 18 (64.4) 24 (75.2) 18 (64.4)

Min. 16 (60.8) - -15 (5.0) -16 (3.2) -15 (5.0) -16 (3.2)

Temperature

°C (°F)

Multi split outdoor unit

*

3

DBT WBT

COOL

Max. 43 (109.4) 26 (78.8)

Min. 16 (60.8) 11 (51.8)

HEAT

Max. 24 (75.2) 18 (64.4)

Min. -10 (14.0) -11 (12.2)

DBT: Dry bulb temperature, WBT: Wet bulb temperature

*

1

CU-TZ20WKE, CU-TZ25WKE, CU-TZ35WKE, CU-TZ42WKE, CU-TZ50WKE, CU-TZ60WKE, CU-TZ71WKE,

CU-RZ20WKE, CU-RZ25WKE, CU-RZ35WKE, CU-RZ50WKE

*

2

CU-2Z35TBE, CU-2Z41TBE, CU-2Z50TBE, CU-3Z52TBE, CU-3Z68TBE, CU-4Z68TBE, CU-4Z80TBE, CU-5Z90TBE

*

3

CU-2TZ41TBE, CU-2TZ50TBE, CU-3TZ52TBE

To learn more...

ACXF55-27151.indb 19ACXF55-27151.indb 19 12/2/2019 10:07:43 AM12/2/2019 10:07:43 AM

20

Cleaning instructions

To ensure optimal performance of the unit,

cleaning has to be carried out at regular

intervals. Dirty unit may caused malfunction

and you may retrieve error code “H 99”.

Please consult authorised dealer.

• Switch off the power supply and unplug before

cleaning.

• Do not touch the aluminium ﬁ n, sharp parts

may cause injury.

• Do not use benzine, thinner or scouring

powder.

• Use only soap ( pH 7) or neutral household

detergent.

• Do not use water hotter than 40 °C / 104 °F.

Indoor unit

( Structure of the unit may vary

depending on the model)

AUTO

OFF/ON

Aluminium ﬁ n

Front panel

Air ﬁ lters

Air Purifying Filter

(

CS-TZ20/25/35/42/50WKEW,

CS-RZ20/25/35/50WKEW,

CS-MTZ16WKE)

Indoor unit

Wipe the unit gently with a soft,

dry cloth.

Coils and fans should be

cleaned periodically by

authorised dealer.

Outdoor unit

Clear debris that surround the

unit.

Clear any blockage from the

drain pipe.

Front panel

Wash gently and dry.

How to remove front panel

1

Raise over

horizontal

level.

2

Pull upward.

Horizontal

Close it securely

AUTO

OFF/ON

1

Hold

horizontally.

2

Match and push in.

3

Close down.

4

Press both ends and center of the front

panel.

Air Purifying Filter

( Fitting location may vary on

models.)

• Do not wash the air purifying ﬁ lter.

• Replace any damaged ﬁ lter.

CS-TZ20/25/35/42/50/60/71WKEW,

MTZ16WKE - Part no.: CZ-SA31P

(replace every 2 years).

CS-RZ20/25/35/50WKEW

- Part no.: CZ-SA32P

(replace every 10 years).

Air Purifying Filter

(CS-TZ60/71WKEW)

Air ﬁ lters

Once every 2 weeks

• Wash/rinse the ﬁ lters gently

with water to avoid damage to

the ﬁ lter surface.

• Dry the ﬁ lters thoroughly under shade,

away from ﬁ re or direct sunlight.

• Replace any damaged ﬁ lters.

Remove air ﬁ lter Attach air ﬁ lter

Insert into the unit

ACXF55-27151.indb 20ACXF55-27151.indb 20 12/2/2019 10:07:43 AM12/2/2019 10:07:43 AM

La page charge ...

Panasonic CU2Z41TBE Mode d'emploi

Panasonic CU2Z41TBE Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents