KitchenAid KRBX109EBL Le manuel du propriétaire

Marque: KitchenAid

Modèle: KRBX109EBL

Catégorie: Frigos

Taper: Le manuel du propriétaire

THANK YOU for purchasing this high-quality product. Register your new refrigerator at www.kitchenaid.com. In Canada, register your

refrigerator at www.kitchenaid.ca.

For future reference, please make a note of your product model and serial numbers. These can be located on the inside wall of the

refrigerator compartment.

Model Number ____________________________________________ Serial Number ____________________________________________

Para obtener acceso a “Instrucciones para el usuario del refrigerador” en español, o para obtener información adicional acerca de su

producto, visite: www.kitchenaid.com.

Necesitará su número de modelo y de serie, ubicado en el interior del compartimiento del refrigerador.

W11304735A

REFRIGERATOR USER INSTRUCTIONS

Table of Contents / Table des matières / Índice

REFRIGERATOR SAFETY .................................. 2

Proper Disposal of Your Old Refrigerator ........3

INSTALLATION INSTRUCTIONS .......................3

Unpack the Refrigerator ..................................3

Location Requirements ...................................4

Electrical Requirements ...................................4

Water Supply Requirements ............................4

Connect the Water Supply ..............................5

Refrigerator Door and Drawer .........................6

Door Closing and Door Alignment ..................9

REFRIGERATOR USE ........................................9

Using the Controls ...........................................9

Electronic Controls ........................................10

Digital Controls ..............................................10

Crisper Humidity Control ...............................11

Ice Maker .......................................................11

Water Dispenser ............................................12

Water Filtration System .................................12

REFRIGERATOR CARE ...................................13

Cleaning .........................................................13

Changing the Light Bulb(s) ............................13

Vacation and Moving Care ............................13

TROUBLESHOOTING ......................................14

Refrigerator Operation ...................................14

Temperature and Moisture .............................15

Ice and Water ................................................. 15

Accessories....................................................16

WATER FILTER CERTIFICATIONS ..................17

PERFORMANCE DATA SHEETS ..................... 18

WARRANTY ......................................................20

SÉCURITÉ DU RÉFRIGÉRATEUR...................21

Mise au rebut du vieux réfrigérateur .............. 23

INSTRUCTIONS D’INSTALLATION .................23

Déballage du réfrigérateur .............................23

Exigences d’emplacement ............................24

Spécications électriques..............................24

Spécications de l’alimentation en eau .........25

Raccordement à la canalisation d’eau ..........25

Porte et tiroir du réfrigérateur ........................27

Fermeture et alignement de la porte .............30

UTILISATION DU RÉFRIGÉRATEUR ..............30

Utilisation des commandes ...........................30

Commandes électroniques ...........................31

Commandes numériques ..............................31

Réglage de l’humidité dans

le bac à légumes ............................................32

Machine à glaçons .........................................33

Distributeur d’eau ..........................................33

Système de ltration d’eau ............................34

ENTRETIEN DU RÉFRIGÉRATEUR ................34

Nettoyage ......................................................34

Remplacer l’ampoule d’éclairag ....................35

Précautions à prendre pour les vacances

ou le déménagement .....................................35

DÉPANNAGE ..................................................... 36

Fonctionnement du réfrigérateur ...................36

Température et humidité ................................37

Glaçons et eau ...............................................37

Accessoires ....................................................38

FEUILLES DE DONNÉES SUR

LA PERFORMANCE .........................................39

GARANTIE LIMITÉE DES APPAREILS

DE RÉFRIGÉRATION KITCHENAID® ..............41

SEGURIDAD DEL REFRIGERADOR ...............43

Cómo deshacerse adecuadamente

desurefrigerador viejo ..................................45

INSTRUCCIONES DE INSTALACIÓN .............45

Desembale el refrigerador .............................45

Requisitos de ubicación ................................46

Requisitos eléctricos .....................................46

Requisitos de suministro de agua .................47

Conexión del suministro de agua ..................47

Puerta y cajón del refrigerador ......................49

Cierre y alineamiento de las puertas .............52

USO DE SU REFRIGERADOR .........................53

Uso de los controles ......................................53

Controles electrónicos ................................... 53

Controles digitales .........................................53

Control de humedad del cajón

para verduras .................................................55

Fábrica de hielo .............................................55

Dosicador de agua.......................................56

Sistema de ltración de agua ........................56

CUIDADO DEL REFRIGERADOR ...................57

Limpieza .........................................................57

Cómo cambiar el foco ...................................57

Cuidado en las vacaciones y en traslados ....58

SOLUCIÓN DE PROBLEMAS..........................59

Funcionamiento del refrigerador ...................59

Temperatura y humedad ................................60

Hielo y agua ...................................................60

Accesorios .....................................................61

CERTIFICACIONES DE FILTROS DE AGUA ..62

HOJAS DE DATOS DE RENDIMIENTO ..........63

GARANTÍA.........................................................65

REFRIGERATOR SAFETY

You can be killed or seriously injured if you don't immediately

You can be killed or seriously injured if you don't follow

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

SAVE THESE INSTRUCTIONS

■ Plug into a grounded (earthed) outlet.

■ Do not remove ground prong.

■ Do not use an adapter.

■ Do not use an extension cord.

■ Disconnect power before servicing.

■ Replace all parts and panels before operating.

■ Remove doors from your old refrigerator.

■ Use nonflammable cleaner.

■ Do not store or use petrol, flammable liquids or gas in the

vicinity of this or other electrical appliances. The fumes can

cause fires or explosions.

■ Do not store explosive substances such as aerosol cans

with a flammable propellant in this refrigerator.

■ Do not use or place electrical devices inside the refrigerator

compartments if they are not of the type expressly

authorized by the manufacture.

■ Use two or more people to move and install refrigerator.

■ Disconnect power before installing ice maker (on ice maker

kit ready models only).

■ A qualified service technician must install the water line and

ice maker. See installation instruction supplied with

ice maker kit IC13B for complete details.

■ Connect to a potable water supply only.

■ Use a sturdy glass when dispensing ice (on some models).

■ This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

■ Children should be supervised to ensure that they do not

play with the appliance.

■ To avoid the risk of children becoming trapped and

suffocating, do not allow them to play or hide inside the

refrigerator.

■ If the power supply cord is damaged, it must be replaced by

the manufacturer or its service agent or a similarly qualified

person.

Proper Disposal of Your Old Refrigerator

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

– even if they will sit for “just a few days.” If you are getting rid

of your old refrigerator, please follow these instructions to help

prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

■Take off the doors.

■Leave the shelves in place so that children may not easily

climb inside.

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

Remove the Packaging

■Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your ngers. Wipe with warm water

and dry.

■Do not use sharp instruments, rubbing alcohol, ammable

uids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see “Refrigerator Safety.”

■Dispose of/recycle all packaging materials.

Clean Before Using

After you remove all of the packaging materials, clean the inside

of your refrigerator before using it. See the cleaning instructions in

“Refrigerator Care.”

WARNING

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

Important information to know about disposal of

refrigerants:

Dispose of refrigerator in accordance with Federal and Local

regulations. Refrigerants must be evacuated by a licensed,

EPA certified refrigerant technician in accordance with

established procedures.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the oor with

cardboard or hardboard to avoid oor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or

“walk” the refrigerator when trying to move it, as oor

damage could occur.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

Location Requirements

IMPORTANT: This appliance is intended to be used in household

and similar applications such as:

■Staff kitchen areas in shops, ofces and other working

environments;

■Farm houses and by clients in hotels, motels and other

residential type environments;

■Bed and breakfast type environments;

■Catering and similar non-retail applications.

To ensure proper ventilation for your refrigerator, allow for

1/2" (1.25 cm) of space on each side and at the top. Allow for

1" (2.54 cm) of space behind the refrigerator. If your refrigerator

has an ice maker, allow extra space at the back for the water line

connections. When installing your refrigerator next to a xed wall,

leave 2¹⁄2" (6.3 cm) minimum on the hinge side (some models

require more) to allow for the door to swing open.

NOTE: This refrigerator is intended for use in a location where

the temperature ranges from a minimum of 55°F (13°C) to a

maximum of 110°F (43°C). The preferred room temperature range

for optimum performance, which reduces electricity usage and

provides superior cooling, is between 60°F (15°C) and 90°F

(32°C). It is recommended that you do not install the refrigerator

near a heat source, such as an oven or radiator.

Electrical Requirements

Before you move your refrigerator into its nal location, it is

important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 V, 60 Hz., AC only 15 or 20 A fused, grounded electrical

supply is required. It is recommended that a separate circuit

serving only your refrigerator be provided. Use an outlet that

cannot be turned off by a switch. Do not use an extension cord.

If the supply cord is damaged it must be replaced by the

manufacturer or its service agent or similarly qualied person. Do

not use a cord that shows cracks or abrasion damage along its

length or at either the plug or connector end.

NOTE: Before performing any type of installation, cleaning,

or removing a light bulb, turn Cooling OFF. Press both the

Refrigerator Minus (-) button and the Freezer Minus (-) button until

the word OFF appears in each display. Disconnect the refrigerator

from the electrical source. When you are nished, reconnect the

refrigerator to the electrical source and reset the temperature

controls to the desired setting. See “Using the Controls.”

Water Supply Requirements

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

TOOLS NEEDED:

■Flat-blade screwdriver

■7/16" and 1/2" Open-end or

two adjustable wrenches

■1/4" Nut driver

■1/4" Drill bit

■Cordless drill

IMPORTANT:

■Connect to a portable water supply only.

■All installations must meet local plumbing code requirements.

■Do not use a piercing-type or 3/16" (4.76 mm) saddle valve

which reduces water ow and clogs more easily.

■Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

■For models with water lters, the disposable water lter

should be replaced at least every 6 months.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

2¹⁄₂" (6.3 cm)

1/2" (1.25 cm)

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Water Pressure

A cold water supply with water pressure of between 35 and 120

psi (241 and 827 kPa) is required to operate the water dispenser

and ice maker. If you have questions about your water pressure,

call a licensed, qualied plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of

a reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 35 and 120 psi (241 and

827 kPa).

If a reverse osmosis water ltration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

■Check to see whether the sediment lter in the reverse

osmosis system is blocked. Replace the lter if necessary.

■Allow the storage tank on the reverse osmosis system to rell

after heavy usage.

■If your refrigerator has a water lter, it may further reduce

the water pressure when used in conjunction with a reverse

osmosis system. Remove the water lter. See “Water Filtration

System.”

If you have questions about your water pressure, call a licensed,

qualied plumber.

Connect the Water Supply

Read all directions before you begin.

IMPORTANT:

■Plumbing shall be installed in accordance with the

International Plumbing Code and any local codes and

ordinances.

■The gray water tubing on the back of the refrigerator (which

is used to connect to the household water line) is a PEX

(cross-linked polyethylene) tube. Copper and PEX tubing

connections from the household water line to the refrigerator

are acceptable, and will help avoid off-taste or odor in your

ice or water. Check for leaks.

■If PEX tubing is used instead of copper, we recommend the

following Whirlpool Part Numbers:

W10505928RP (7 ft [2.14 m] jacketed PEX),

8212547RP (5 ft [1.52 m] PEX), or

W10267701RP (25 ft [7.62 m] PEX).

■Install tubing only in areas where temperatures will remain

above freezing.

■If you turn on the refrigerator before the water line is

connected, turn off the ice maker to avoid excessive noise or

damage to the water valve.

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Find a 1/2" to 1¹⁄4" (12.7 mm to 31.8 mm) vertical cold water

pipe near the refrigerator.

■Make sure it is a cold water pipe.

■Horizontal pipe will work, but the following procedure

must be followed: Drill on the top side of the pipe, not the

bottom. This will help keep water away from the drill. This

also keeps normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure

from the connection on the lower right rear of the refrigerator

to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use

1/4" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure

both ends of copper tubing are cut square.

5. Using a cordless drill, drill a 1/4" hole in the cold water pipe

you have selected.

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the 1/4" drilled hole

in the water pipe and that the washer is under the pipe clamp.

Tighten the packing nut. Tighten the pipe clamp screws slowly

and evenly so the washer makes a watertight seal. Do not

overtighten.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not overtighten or

you may crush the copper tubing.

8. Place the free end of the tubing in a container or sink, and

turn ON the main water supply. Flush the tubing until water is

clear. Turn OFF the shutoff valve on the water pipe.

Connect to Refrigerator

Depending on your model, the water line may come down from

the top or up from the bottom. Follow the connection instructions

for your model.

Style 1

1. Remove plastic cap from water valve inlet port. Attach the

copper tube to the valve inlet using a compression nut

and sleeve as shown. Tighten the compression nut. Do not

overtighten. Conrm copper tubing is secure by pulling on

copper tubing.

2. Create a service loop with the copper tubing. Avoid kinks

when coiling the copper tubing. Secure copper tubing to

refrigerator cabinet with a “P” clamp.

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

A. Cold water pipe

B. Pipe clamp

C. Copper tubing

D. Compression nut

E. Compression sleeve

F. Shutoff valve

G. Packing nut

3. Turn on water supply to refrigerator and check for leaks.

Correct any leaks.

Style 2

1. Create a service loop (minimum diameter of 2 ft [61 cm])

with the copper tubing. Avoid kinks when coiling the copper

tubing.

2. Remove the plastic cap from water valve inlet port. Place a

compression nut and sleeve on the copper tubing.

3. Insert the end of the copper tubing into the water valve inlet

port. Shape tubing slightly so that the tubing feeds straight

into the port to avoid kinks.

4. Slide the compression nut over the sleeve and screw into the

water valve inlet port.

5. Using an adjustable wrench, hold the nut on the plastic water

line to keep it from moving. Then, with a second wrench turn

the compression nut on the copper tubing counterclockwise

to completely tighten. Do not overtighten.

6. Check connection by pulling on copper tubing. Attach the

plastic water line to the refrigerator cabinet with a “P” clamp.

7. Turn on water supply to the refrigerator and check for leaks.

Correct any leaks.

Complete the Installation

1. Plug into a grounded 3 prong outlet.

NOTE: Allow 24 hours to produce the rst batch of ice.

Discard the rst three batches of ice produced. Allow 3 days to

completely ll the ice storage bin.

Refrigerator Door and Drawer

All graphics referenced in the following instructions are included

later in this section after “Final Steps.”

TOOLS NEEDED: 5/16", 3/8", 1/4" hex-head socket wrench,

a 3/32" hex key, #2 Phillips screwdriver, and a at-blade

screwdriver.

Remove and Replace Handles

1. Using a 3/32" hex key, loosen the two setscrews located on

the side of each handle. See graphics 2 and 4.

2. Pull the handle straight out from the door. Make sure you keep

the screws for reattaching handles.

3. To replace the handle, reverse the directions.

Remove Door and Hinges

IMPORTANT: Remove food and any adjustable door bins or utility

bins from doors.

1. Unplug refrigerator or disconnect power.

A. Copper tubing

B. “P” clamp

C. Compression nut

D. Compression sleeve

A. Plastic water tubing

B. Sleeve

C. Compression nut

D. Copper tubing

A. “P” clamp

B. Plastic water line

C. Compression nut

D. Copper tubing

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

2. Keep the refrigerator door closed until you are ready to lift it

free from the cabinet.

NOTE: Provide additional support for the refrigerator door

while the hinges are being moved. Do not depend on the

door gasket magnets to hold the door in place while you are

working.

3. Remove the parts for the top hinge as shown in Top Hinge

Graphic. Lift the refrigerator door free from the cabinet.

4. Remove the parts for the bottom hinge as shown in the

Bottom Hinge Graphic.

Reverse Door

IMPORTANT: If you want to reverse your doors so they open from

the opposite side, follow these steps. If you are not reversing the

doors, see “Replace Door and Hinges”.

Cabinet

1. Remove the hinge screws from handle side and move them to

opposite side. See Graphic 1-1.

2. Using a at-blade screwdriver tip wrapped in masking tape,

remove the cabinet hinge hole plugs from the cabinet top

and move them to the opposite side hinge holes as shown in

Graphic 1-2.

Refrigerator door

1. Remove the refrigerator handle assembly including the

mounting posts and screws. Keep all parts together. See

Graphic 2.

2. Remove the door handle seal screw front. Move to opposite

side of refrigerator door as shown in Graphic 5.

3. Remove the door stop from the bottom edge of the

refrigerator door. Move to opposite side of refrigerator door as

shown in Graphic 3.

4. Attach the door handle mounting posts to the opposite side of

the door.

5. Position refrigerator handle over mounting posts as shown in

Graphic 2. Drive two setscrews in the sides of the handle.

6. Tighten all screws. Set aside the door until the hinges and

freezer compartment drawer are in place.

Replace Door and Hinges

NOTE: When reversing panel series door, use alternate top hinge

shipped with refrigerator.

1. Replace the parts for the bottom hinge as shown in Bottom

Hinge graphic. Tighten screws. Replace the refrigerator door.

NOTE: Provide additional support for the refrigerator door

while the hinges are being moved. Do not depend on the

door gasket magnets to hold the door in place while you are

working.

2. Assemble the parts for the top hinge as shown in the Top

Hinge Graphic. Do not tighten screws completely.

3. Line up the door so that the bottom of the refrigerator door

aligns evenly with the top of the freezer drawer. Tighten all

screws.

Freezer Drawer

IMPORTANT: Two people may be required to remove and replace

the freezer drawer.

Remove Drawer Front

1. Open the freezer drawer to full extension.

2. Loosen the four screws attaching the drawer glides to the

drawer front. See Drawer Front Removal graphic.

NOTE: Loosen screws three to four turns. Keep the screws in

the drawer front.

3. Lift drawer front upward and off the screws. See Drawer Front

Removal graphic.

Replace Drawer Front

1. Slide the drawer glides out of the freezer compartment. Insert

the screws in the top of the drawer front into the slots in the

drawer brackets. See Drawer Front Replacement graphic.

2. Pull the drawer brackets toward you to position the two

screws in the bottom of the drawer front into the brackets.

See Drawer Front Replacement graphic.

3. Completely tighten the four screws.

4. Replace the base grille.

Final Steps

1. Check all holes to make sure that hole plugs and screws are

in place. Reinstall top hinge cover. See Top Hinge Graphic.

2. Plug into a grounded 3 prong outlet.

3. Return all removable door parts to doors and food to

refrigerator.

5/16" Hex Head Top Hinge Screw

Door Stop Screw

Cabinet Hinge Hole PlugFlat-Head Handle Screw

Door Handle Seal Screw

Front

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

1-2

1-1

Door Removal &

Replacement

Top Hinge

Bottom Hinge

Door Swing Reversal (optional)

A. Hinge Cover Screw

B. Top Hinge Cover

C. 5/16" Hex-Head Hinge Screws

D. Top Hinge

A. Shim (on some models)

B. Center Hinge

C. Hinge Screws

Drawer Front Removal Drawer Front Replacement

A. 3/32" Setscrew

A. Door Stop Screws

B. Door Stop

A. 3/32" Setscrew

Door Handle

Seal Screw

Front

A. Loosen 4 Door Bracket Screws

Front View Side View

A. Cabinet Hinge Hole Plugs

A. Hinge Screws

Door Closing and Door Alignment

The base grille covers the leveling screws and roller assemblies

located at the bottom of the refrigerator cabinet below the freezer

door or drawer. Before making adjustments, remove the base

grille and move the refrigerator to its nal location.

1. Remove the two screws fastening the base grille to the

cabinet, and set the screws aside. Grasp the grille and pull it

toward you.

2. Move the refrigerator to its nal location.

NOTE: To allow the refrigerator to roll easier, raise the

leveling legs off the oor by turning the leveling screws

counterclockwise. The front rollers will be touching the oor.

3. So the doors will close easier, use a 1/4" hex driver to turn

both leveling screws clockwise. This will raise the front of the

refrigerator tilting it slightly downward to the rear. Turn both

leveling screws the same amount.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws. This

makes it easier to turn the screws.

4. Open and close the doors to make sure they close as easily

as you like. If not, increase the tilt by turning both leveling

screws clockwise. It may take several turns of the leveling

screw to allow the doors to close easier.

5. Check for door alignment. If one door is lower than the other,

adjust the leveling screw, on the lower side of the refrigerator.

Using a 1/4" hex driver, turn the screw clockwise to raise that

side of the refrigerator until the doors are aligned. It may take

several turns of the leveling screw to raise the refrigerator.

NOTE: Having someone push against the top of the refrigerator

takes some weight off the leveling screws. This makes it easier to

turn the screws.

6. Make sure the refrigerator is steady. If the refrigerator seems

unsteady or rolls forward when the door or drawer is opened

adjust the leveling screws. Using a 1/4" hex driver, turn the

leveling screw on each side clockwise until the rollers are up

and the leveling feet are rmly against the oor.

7. Replace the base grille by aligning the holes in the grille with

the holes in the cabinet and fasten using the screws removed

in Step 1.

REFRIGERATOR USE

Using the Controls

Your model may have Electronic Controls or Digital Controls.

IMPORTANT:

■Wait 24 hours for your refrigerator to cool completely before

adding food. If you add food before the refrigerator has

cooled completely, your food may spoil.

NOTE: Adjusting the Refrigerator and Freezer Controls to a

higher (colder) than recommended setting will not cool the

compartments any faster.

■The recommended settings should be correct for normal

household refrigerator use. The controls are set correctly

when milk or juice is as cold as you like and when ice cream

is rm.

■If the temperature is too warm or too cold in the refrigerator

or freezer, rst check the air vents to be sure they are not

blocked before adjusting the controls.

¹⁄₄"

A. Leveling screw

B. Front roller

¹⁄₄"

Electronic Controls

For your convenience, your refrigerator and freezer controls are

preset at the factory. When you rst install your refrigerator, make

sure the controls are still set to the recommended setting as

shown.

Recommended Setting “4”

To Turn Your Refrigerator Off/On:

■To turn the refrigerator off, press the freezer Minus (-) touch

pad until a dash (-) appears in both the refrigerator and freezer

displays. Neither compartment will cool.

Adjusting Electronic Controls

The temperature control range for each compartment is 1 through

7 (coldest).

Press the Plus (+) or Minus (-) touch pads to adjust the

temperature. Except when starting the refrigerator, do not adjust

either control more than one setting at a time. Wait 24 hours

between adjustments for the temperature to stabilize.

If you need to adjust the temperature in either the refrigerator or

freezer compartment, use the settings listed in the chart below as

a guide.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm Adjust REFRIGERATOR

Control one setting higher

FREEZER too warm/to little ice Adjust FREEZER Control

one setting higher

REFRIGERATOR too cold Adjust REFRIGERATOR

Control one setting lower

FREEZER too cold Adjust FREEZER Control

one setting lower

Digital Controls

For your convenience, your temperature controls are preset at

the factory. When you rst install your refrigerator, make sure the

controls are still set to the recommended set points as shown.

IMPORTANT: When the power is on, the temperature display

shows the set point temperature of the compartment.

Recommended Settings

To Turn Your Refrigerator Off/On:

■Press the freezer (+) touch pad repeatedly until “OFF” appears

in the freezer display. Allow a few seconds for the refrigerator

to shut off. Neither compartment will cool.

■Press either the refrigerator or freezer (-) touch pad to turn on

the refrigerator.

Adjusting Controls

The REFRIGERATOR control adjusts the refrigerator compartment

temperature. The FREEZER control adjusts the freezer

compartment temperature.

If you need to adjust the temperature in either the refrigerator

or freezer compartment, use the settings listed in the chart as a

guide.

To Adjust Set Point Temperatures:

The rst touch of the (+) or (-) touch pad displays the current

temperature set point.

■Press the (+) or (-) touch pads until the desired temperature

set point is displayed.

NOTE: Except when rst turning on the refrigerator, do not

adjust either temperature control more than one setting at a

time. Wait 24 hours between adjustments for the temperature

to stabilize.

CONDITION/REASON: ADJUSTMENT

REFRIGERATOR too warm REFRIGERATOR Control

1° lower

FREEZER too warm/too little ice Adjust FREEZER Control

1° lower

REFRIGERATOR too cold Adjust REFRIGERATOR

Control 1° higher

FREEZER too cold Adjust FREEZER Control

1° higher

Additional Control Center Features

Max Ice

The Max Ice feature assists with temporary periods of heavy ice

use by increasing ice production.

■Press the Max Ice feature touch pad to set the freezer to the

lowest temperature setting. Press the Max Ice feature touch

pad again to return to the normal freezer set point.

NOTE: The Max Ice feature will automatically shut off in

approximately 24 hours.

Humidity Control

The Humidity Control feature turns on a heater to help reduce

moisture on the door hinge seal. Use in humid environments or

when you notice moisture on the door hinge seal. The refrigerator

uses more energy when Humidity Control is on.

■Press Humidity Control when the environment is warm and

more humid, or if you notice moisture on the door hinge seal.

The indicator light will be lit when humidity control is ON.

■Press Humidity Control to save energy when the environment

is less humid.

Temp Alarm

The Temp Alarm feature provides temperature information in the

event of a power outage.

Power outage: During a power outage, if the temperatures in the

refrigerator and freezer compartments exceed normal operating

temperatures, the highest temperature reached will be displayed.

■Press the Temp Alarm touch pad until the indicator light is

lit, to turn on this feature. Press and hold Temp Alarm for

3 seconds until the indicator light goes off to turn off this

feature.

Temperature alarm: An alarm will sound repeatedly if the

freezer or refrigerator compartment temperatures exceed normal

operating temperatures for an hour or more.

The temperature displays will alternately show the current

temperatures and the highest temperatures the compartments

reached.

■Press the Temp Alarm touch pad once to stop the audible

alarm and alternating temperature displays. The Temp Alarm

light will continue to ash until the refrigerator returns to the

set temperature.

Door Alarm

The Door Alarm feature sounds a chime every few seconds when

the refrigerator door has been left open for 5 continuous minutes.

The chime will sound until the door is closed or Door Alarm is

turned off.

■Press the Door Alarm touch pad to turn this feature on or off.

The indicator light will be lit when the Door Alarm feature is

on.

Max Cool

The Max Cool feature assists with periods of high refrigerator use,

full grocery loads, or temporarily warm room temperatures.

■Press Max Cool to set the freezer and refrigerator to the

lowest temperature settings. Press Max Cool again to return

to the normal refrigerator set point.

NOTE: The Max Cool feature will automatically shut off in

approximately 12 hours.

Filter Reset

The Filter Reset control allows you to restart the water lter status

tracking feature each time you replace your water lter. See

“Water Filtration System.”

■Press and hold the Filter Reset touch pad for 3seconds, until

the Order or Replace light turns off.

User Preferences

The control center allows you to set user preferences, if desired.

Temperature Display (F_C)

This preference allows you to change the temperature display.

F - Temperature in degrees Fahrenheit

C - Temperature in degrees Celsius

Alarm (AL)

This preference allows you to turn off the sound of all alarms.

ON - You will hear the alarm sound.

OFF - You will not hear the alarm sound.

To Access the User Preferences Menu:

1. Press and hold the Door Alarm touch pad for 3 seconds. The

preference name will appear in the Freezer display and the

preference status (F or C) or (ON or OFF) will appear in the

Refrigerator display.

2. Use the Freezer (+) or (-) touch pads to scroll through the

preference names. When the desired preference name is

displayed, press the Refrigerator (+) or (-) touch pads to

change the preference status.

3. Set your preferences by pressing and holding the Door Alarm

touch pad for 3 seconds, or by shutting the refrigerator

compartment door.

Crisper Humidity Control

You can control the amount of humidity in the moisture-sealed

crisper. Depending on your model, adjust the control to any

setting between FRUIT and VEGETABLES or LOW and HIGH.

FRUIT/LOW (open) for best storage of fruits and vegetables with

skins.

VEGETABLES/HIGH (closed) for best storage of fresh, leafy

vegetables.

Ice Maker

IMPORTANT: Flush the water system before turning on the ice

maker. See “Water Dispenser.”

Turning the Ice Maker On/Off

To turn the ice maker ON, simply lower the wire shutoff arm.

To manually turn the ice maker OFF, lift the wire shutoff arm to the

OFF (arm up) position and listen for the click.

NOTE: Your ice maker has an automatic shutoff. As ice is made,

the ice cubes will ll the ice storage bin and the ice cubes will

raise the wire shutoff arm to the OFF (arm up) position. Do not

force the wire shutoff arm up or down.

NOTE: Turn off the ice maker before removing the ice storage bin

to serve ice or to clean the bin. This will keep the ice cubes from

dropping out of the ice maker and into the freezer compartment.

After replacing the ice storage bin, turn on the ice maker.

Ice Production Rate

■The ice maker should produce a complete batch of ice

approximately every 3 hours.

■To increase ice production, lower the freezer and refrigerator

temperature. See “Using the Controls.” Wait 24 hours

between adjustments.

Remember

■Allow 24 hours to produce the rst batch of ice. Allow 3 days

to completely ll the ice storage bin. Discard the rst three

batches of ice produced.

■The quality of your ice will be only as good as the quality of

the water supplied to your ice maker. Avoid connecting the ice

maker to a softened water supply. Water softener chemicals

(such as salt) can damage parts of the ice maker and lead

to poor quality ice. If a softened water supply cannot be

avoided, make sure the water softener is operating properly

and is well maintained.

■Do not store anything on top of the ice maker or in the ice

storage bin.

Water Dispenser

IMPORTANT:

■After connecting the refrigerator to a water source or replacing

the water lter, ush the water system. Use a sturdy container

to depress and hold the water dispenser lever for 5 seconds,

then release it for 5 seconds. Repeat until water begins to

ow. Once water begins to ow, continue depressing and

releasing the dispenser lever (5 seconds on, 5 seconds off)

until a total of 4 gal. (15 L) has been dispensed. This will ush

air from the lter and water dispensing system, and prepare

the water lter for use. Additional ushing may be required in

some households. As air is cleared from the system, water

may spurt out of the dispenser.

NOTE: After 5 minutes of continuous dispensing, the

dispenser will stop dispensing water to avoid ooding. To

continue dispensing, press the dispenser button again.

■Allow 24 hours for the refrigerator to cool down and chill

water. Dispense enough water every week to maintain a fresh

supply.

Dispensing Water

1. Hold a container under the dispenser while pressing the

button.

2. Release the button to stop dispensing.

Water Filtration System

The water lter is located in the upper right-hand corner of the

refrigerator compartment.

Water Filter Status Lights

The water lter status lights will help you know when to change

the water lter. When the Order light is on, it is almost time to

change the water lter. When the Replace light is on, a new water

lter should be installed.

After replacing the water lter, press and hold FILTER RESET for 3

seconds until the Order or Replace light turns off. See “Using the

Controls.”

IMPORTANT: The disposable water lter should be replaced at

least every 6 months. If the water ow to the water dispenser or

ice maker decreases noticeably before 6 months have passed,

replace the water lter more often.

Replacing the Water Filter

To purchase a replacement water lter, see Accessories.

IMPORTANT: Air trapped in the water system may cause water

and lter to eject. Always dispense water for at least 2 minutes

before removing the lter or blue bypass cap.

1. Turn lter counterclockwise to remove.

2. Remove sealing label from replacement lter and insert the

lter end into the lter head.

3. Turn the lter clockwise until it stops. Snap the lter cover

closed.

4. Flush the water system. See “Water Dispenser” or “Water and

Ice Dispenser.”

NOTE: The dispenser feature may be used without a water lter

installed. Your water will not be ltered. If this option is chosen,

replace the lter with the blue bypass cap.

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

REFRIGERATOR CARE

Cleaning

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to avoid

buildup of odors. Wipe up spills immediately.

IMPORTANT:

■Because air circulates between both sections, any odors

formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid

odor transfer and drying out of food, wrap or cover foods

tightly.

■For stainless steel models, stainless steel is corrosion-

resistant and not corrosion-proof. To help avoid corrosion of

your stainless steel, keep your surfaces clean by using the

following cleaning instructions.

To Clean Your Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, ammable uids, muriatic acid,

cleaning waxes, concentrated detergents, bleaches or cleansers

containing petroleum products on exterior surfaces (doors and

cabinet), plastic parts, interior and door liners or gaskets. Do not

use paper towels, scouring pads, or other harsh cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

3. Clean the exterior surfaces.

Painted metal: Wash painted metal exteriors with a clean,

soft cloth or sponge and a mild detergent in warm water.

Rinse surfaces with clean, warm water and dry immediately to

avoid water spots.

Stainless steel: Wash stainless steel surfaces with a clean,

soft cloth or sponge and a mild detergent in warm water.

Rinse surfaces with clean, warm water and dry immediately to

avoid water spots.

NOTE: When cleaning stainless steel, always wipe in the

direction of the grain to avoid cross-grain scratching.

4. There is no need for routine condenser cleaning in normal

home operating environments. If the environment is

particularly greasy or dusty, or there is signicant pet trafc in

the home, the condenser should be cleaned every

2 to 3 months to ensure maximum efciency.

If you need to clean the condenser:

■Remove the base grille.

■Use a vacuum cleaner with a soft brush to clean the grille,

the open areas behind the grille and the front surface area

of the condenser.

■Replace the base grille when nished.

5. Plug in refrigerator or reconnect power.

Changing the Light Bulb(s)

IMPORTANT: The lighting system in this appliance may consist

of:

■Sealed LED modules

■LED Bulbs

■Incandescent Bulbs

■Or a combination of the above.

If a Sealed LED module(s) do not illuminate when the refrigerator

and/or freezer door is opened, call for assistance or service. See

“Warranty” for contact information.

If a LED Bulb does not illuminate when the refrigerator and/

or freezer door is opened, replace with like bulb following this

procedure:

1. Unplug the refrigerator or disconnect power.

2. Remove the light shield (on some models).

■Remove the hardware holding the light shield in place.

■Top of the refrigerator compartment - Slide the light shield

toward the back of the compartment to release it from the

light assembly.

3. Replace the burned-out bulb(s) with a bulb of the same size,

shape and wattage.

■Order Part Number W10565137 (3.6 W).

NOTE: Some LED replacement bulbs are not recommended

for wet/damp environments. The refrigerator and freezer

compartments are considered to be wet/damp environments.

If using a brand of LED bulb other than the recommended LED

bulb, before installation, read and follow all instructions on the

LED packaging.

4. Replace the light shield by inserting the tabs on the shield into

the liner holes on each side of the light assembly. Slide the

shield toward the front until it locks into place.

NOTE: To avoid damaging the light shield, do not force the

shield beyond the locking Point.

5. Replace the hardware that holds the shield in place.

6. Plug in the refrigerator or reconnect power.

If an incandescent bulb does not illuminate when the refrigerator

and/or freezer door is opened, replace with like bulb using the

same procedure outlined above. Replace burned out bulb with

only incandescent bulb(s) of the same size, shape and wattage

(maximum 40 W) designed for household appliances.

Vacation and Moving Care

Vacations

If You Choose to Leave the Refrigerator On While You’re

Away:

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker, and is

connected to the household water supply, turn off the water

supply to the refrigerator. Property damage can occur if the

water supply is not turned off.

3. If you have an automatic ice maker, turn off the ice maker.

NOTE: Depending on your model, raise the wire shutoff arm

to OFF (up) position, or press the switch to OFF.

4. Empty the ice bin.

WARNING

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

If You Choose to Turn Off the Refrigerator Before You

Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

■Turn off the water supply to the ice maker at least one day

ahead of time.

■When the last load of ice drops, raise the wire shutoff

arm to the OFF (up) position or press the switch to OFF,

depending on your model.

3. Turn off the Temperature control(s). See “Using the Control(s).”

4. Clean refrigerator, wipe it, and dry well.

5. Tape rubber or wood blocks to the tops of both doors to prop

them open far enough for air to get in. This stops odor and

mold from building up.

Moving

When you are moving your refrigerator to a new home, follow

these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

■Turn off the water supply to the ice maker at least one day

ahead of time.

■Disconnect the water line from the back of the refrigerator.

■When the last load of ice drops, raise the wire shutoff

arm to the OFF (up) position or press the switch to OFF,

depending on your model.

2. Remove all food from the refrigerator and pack all frozen food

in dry ice.

3. Empty the ice bin.

4. Turn off the Temperature control(s). See “Using the Control(s).”

5. Unplug refrigerator.

6. Clean, wipe, and dry thoroughly.

7. Take out all removable parts, wrap them well, and tape them

together so they don’t shift and rattle during the move.

8. Depending on the model, raise the front of the refrigerator so

it rolls more easily OR raise the leveling screws so they don't

scrape the oor. See “Adjust the Door(s)” or “Door Closing

and Door Alignment.”

9. Tape the doors closed and tape the power cord to the back of

the refrigerator.

When you get to your new home, put everything back and refer to

the “Installation Instructions” section for preparation instructions.

Also, if your refrigerator has an automatic ice maker, remember to

reconnect the water supply to the refrigerator.

TROUBLESHOOTING

First try the solutions suggested here. If you need further assistance or more recommendations that may help you avoid a service call,

refer to the warranty page in this manual and visit http://kitchenaid.custhelp.com.

In Canada, visit www.kitchenaid.ca (website may not be compatible with some mobile devices).

In the U.S.A.:

KitchenAid Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

In Canada:

KitchenAid Brand Home Appliances

Customer eXperience Centre

200 – 6750 Century Ave.

Mississauga, Ontario L5N 0B7

Please include a daytime phone number in your correspondence.

Refrigerator Operation

The refrigerator will not operate

■Power cord unplugged? Plug into a grounded 3 prong outlet.

■Is outlet working? Plug in a lamp to see if the outlet is

working.

■Household fuse blown or circuit breaker tripped? Replace

the fuse or reset the circuit breaker. If the problem continues,

call an electrician.

■Are controls on? Make sure the refrigerator controls are on.

See “Using the Control(s).”

■New installation? Allow 24 hours following installation for the

refrigerator to cool completely.

NOTE: Adjusting the temperature controls to coldest setting

will not cool either compartment more quickly.

The motor seems to run too much

Your new refrigerator may run longer than your old one due to

its high-efciency compressor and fans. The unit may run even

longer if the room is warm, a large food load is added, doors are

opened often, or if the doors have been left open.

The refrigerator seems noisy

Refrigerator noise has been reduced over the years. Due to

this reduction, you may hear intermittent noises from your new

refrigerator that you did not notice from your old model. Below

are listed some normal sounds with explanations.

■Buzzing - heard when the water valve opens to ll the ice

maker

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

■Pulsating - fans/compressor adjusting to optimize

performance

■Hissing/Rattling - ow of refrigerant, movement of water

lines, or from items placed on top of the refrigerator

■Sizzling/Gurgling - water dripping on the heater during

defrost cycle

■Popping - contraction/expansion of inside walls, especially

during initial cool-down

■Water running - may be heard when ice melts during the

defrost cycle and water runs into the drain pan

■Creaking/Cracking - occurs as ice is being ejected from the

ice maker mold.

The doors will not close completely

■Door blocked open? Move food packages away from door.

■Bin or shelf in the way? Push bin or shelf back in the correct

position.

The doors are difcult to open

■Gaskets dirty or sticky? Clean gaskets and contact surfaces

with mild soap and warm water. Rinse and dry with soft cloth.

Temperature and Moisture

Temperature is too warm

■New installation? Allow 24 hours following installation for the

refrigerator to cool completely.

■Door(s) opened often or left open? Allows warm air to enter

refrigerator. Minimize door openings and keep doors fully

closed.

■Large load of food added? Allow several hours for

refrigerator to return to normal temperature.

■Controls set correctly for the surrounding conditions?

Adjust the controls a setting colder. Check temperature in

24 hours. See “Using the Control(s).”

There is interior moisture buildup

NOTE: Some moisture buildup is normal.

■Humid room? Contributes to moisture buildup.

■Door(s) opened often or left open? Allows humid air to enter

refrigerator. Minimize door openings and keep doors fully

closed.

Ice and Water

The ice maker is not producing ice or not enough ice

■Refrigerator connected to a water supply and the supply

shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

■Kink in the water source line? A kink in the line can reduce

water ow. Straighten the water source line.

■Ice maker turned on? Make sure wire shutoff arm or switch

(depending on model) is in the ON position.

■New installation? Wait 24 hours after ice maker installation

for ice production to begin. Wait 72 hours for full ice

production.

■Freezer door closed completely? Firmly close the freezer

compartment door. If the freezer compartment door will not

close all the way, see “The doors will not close completely,”

earlier in this section.

■Large amount of ice recently removed? Allow 24 hours for

ice maker to produce more ice.

■Ice cube jammed in the ice maker ejector arm?

Remove ice from the ejector arm with a plastic utensil.

■Water lter installed on the refrigerator? Remove lter and

operate ice maker. If ice volume improves, then the lter may

be clogged or incorrectly installed. Replace lter or reinstall it

correctly.

■Reverse osmosis water ltration system connected to

your cold water supply? This can decrease water pressure.

See “Water Supply Requirements.”

The ice cubes are hollow or small

NOTE: This is an indication of low water pressure.

■Water shutoff valve not fully open? Turn the water shutoff

valve fully open.

■Kink in the water source line? A kink in the line can reduce

water ow. Straighten the water source line.

■Water lter installed on the refrigerator? Remove lter and

operate ice maker. If ice quality improves, then the lter may

be clogged or incorrectly installed. Replace lter or reinstall it

correctly.

■Reverse osmosis water ltration system connected to

your cold water supply? This can decrease water pressure.

See “Water Supply Requirements.”

■Questions remain regarding water pressure? Call a

licensed, qualied plumber.

Off-taste, odor or gray color in the ice

■New plumbing connections? New plumbing connections

can cause discolored or off-avored ice.

■Ice stored too long? Discard ice. Wash ice bin. Allow

24 hours for ice maker to make new ice.

■Odor transfer from food? Use airtight, moisture proof

packaging to store food.

■Are there minerals (such as sulfur) in the water? A water

lter may need to be installed to remove the minerals.

■Water lter installed on the refrigerator? Gray or dark

discoloration in ice indicates that the water ltration system

needs additional ushing. Flush the water system before using

a new water lter. Replace water lter when indicated. See

“Water Filtration System.”

WARNING

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

The water dispenser will not operate properly

■Refrigerator connected to a water supply and the supply

shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

■Kink in the water source line? Straighten the water source

line.

■New installation? Flush and ll the water system. See “Water

Dispenser.”

■Is the water pressure at least 35 psi (241 kPa)? The water

pressure to the home determines the ow from the dispenser.

See “Water Supply Requirements.”

■Water lter installed on the refrigerator? Remove lter and

operate dispenser. If water ow increases, the lter may be

clogged or incorrectly installed. Replace lter or reinstall it

correctly.

■Refrigerator door closed completely? Close the door rmly.

If it does not close completely, see “The doors will not close

completely,” earlier in this section.

■Recently removed the doors? Make sure the water

dispenser wire/tube assembly has been properly reconnected.

See “Refrigerator Door(s) and Drawer.”

■Reverse osmosis water ltration system connected to

your cold water supply? This can decrease water pressure.

See “Water Supply Requirements.”

Water is leaking from the dispenser system

NOTE: One or two drops of water after dispensing is normal.

■Glass not being held under the dispenser long enough?

Hold the glass under the dispenser 2 to 3 seconds after

releasing the dispenser lever.

■New installation? Flush the water system. See “Water

Dispenser.”

■Recently changed water lter? Flush the water system. See

“Water Dispenser.”

■Water on the oor near the base grille? Make sure the

water dispenser tube connections are fully tightened. See

“Refrigerator Door(s) and Drawer.”

Water from the dispenser is warm

NOTE: Water from the dispenser is only chilled to 50°F (10°C).

■New installation? Allow 24 hours after installation for the

water supply to cool completely.

■Recently dispensed large amount of water? Allow 24 hours

for water supply to cool completely.

■Water not been recently dispensed? The rst glass of water

may not be cool. Discard the rst glass of water.

■Refrigerator connected to a cold water pipe? Make sure

the refrigerator is connected to a cold water pipe. See “Water

Supply Requirements.”

Accessories

The following accessories are available for your refrigerator. To

order an accessory, contact us and ask for the part number.

In the U.S.A., visit our website www.kitchenaid.com or call

1-800-422-1230.

In Canada, visit our webpage www.whirlpoolparts.ca

or call 1-800-807-6777.

Affresh® Stainless Steel Cleaner:

In U.S.A., order Part #W10355016

In Canada, order Part #W10355016B

Affresh® Stainless Steel Wipes:

In U.S.A., order Part #W10355049

In Canada, order Part #W10355049B

Affresh® Kitchen & Appliance Cleaner:

In U.S.A., order Part #W10355010

In Canada, order Part #W10355010B

Water Filter:

Order Model #67003523-750

Order Model #UKF8001AXX-200

Produce Preserver (on some models):

Order Part #W10346771A

WATER FILTER CERTIFICATIONS

PERFORMANCE DATA SHEETS

Interior Water Filtration System

Model 67003523-750 Capacity 750 Gallons (2839 Liters))

This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The

concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the

permissible limit for water leaving the system, as specied in NSF/ANSI Standards 42 and 53.

Substance Reduction

Aesthetic Effects

NSF Reduction

Requirements

Average

Inuent

Inuent Challenge

Concentration

Maximum

Efuent

Average

Efuent

Minimum%

Reduction

Average%

Reduction

Chlorine Taste/Odor

Particulate Class I*

50% reduction

85% reduction

2.00 mg/L

14,000,000 #/mL

2.0 mg/L ± 10%

At least

10,000 particles/mL

0.06 mg/L

370,000 #/mL**

0.050625 mg/L

196,666 #/mL

97.00%

97.40%

97.52%

99.00%

Contaminant

Reduction

NSF Reduction

Requirements

Average

Inuent

Inuent Challenge

Concentration

Maximum

Efuent

Average

Efuent

Minimum%

Reduction

Average%

Reduction

Lead: @ pH 6.5

Lead: @ pH 8.5

0.010 mg/L

0.150 mg/L†

0.15 mg/L ± 10%

< 0.001 mg/L

>99.30%

Mercury: @ pH 6.5

Mercury: @ pH 8.5

0.002 mg/L

0.006 mg/L

0.0059 mg/L

0.006 mg/L ± 10%

0.0005 mg/L

0.0018 mg/L

0.0003 mg/L

0.00073 mg/L

91.70%

69.20%

95.00%

88.10%

Benzene 0.005 mg/L 0.0133 mg/L 0.015 mg/L ± 10% 0.0005 mg/L 0.0005 mg/L 96.10% 96.30%

p-Dichlorobenzene 0.075 mg/L 0.210 mg/L 0.225 mg/L ± 10% < 0.0005 mg/L < 0.0005 mg/L >99.80% >99.80%

Carbofuran 0.040 mg/L 0.0753 mg/L 0.08 mg/L ± 10% 0.027 mg/L 0.008 mg/L 64.60% 73.45%

Toxaphene 0.003 mg/L 0.015 mg/L 0.015 ± 10% < 0.001 mg/L < 0.001 mg/L >93.3% >93.3%

Atrazine 0.003 mg/L 0.0102 mg/L 0.009 mg/L ± 10% 0.0027 mg/L 0.00105 mg/L 76.30% 89.40%

Asbestos >99% 126.5 MF/L 107 to 108 bers/L†† < 0.17 MF/L < 0.17 MF/L >99.99% >99.99%

Live Cysts ‡

Turbidity

>99.95%

0.5 NTU

122,500 #/L

10.5 NTU

50,000/L min.

11 ± 1 NTU

< 1 #/L‡

0.30 NTU

< 1 #/L‡

0.125 NTU

>99.99%

97.30%

>99.99%

98.80%

Lindane 0.0002 mg/L 0.0019 mg/L 0.002 ± 10% < 0.00016 mg/L 0.000035 mg/L 91.80% 97.90%

Tetrachloroethylene 0.005 mg/L 0.015 mg/L 0.015 mg/L ± 10% < 0.0005 mg/L < 0.0005 mg/L >96.6% >96.6%

Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.78 gpm (2.9 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F ± 5°F

(20°C ± 3°C).

■It is essential that operational, maintenance, and lter

replacement requirements be carried out for the product to

perform as advertised.

■The disposable water lter should be replaced at least every

6 months.

■The lter monitor system measures the amount of water that

passes through the lter and alerts you to replace the lter.

When 90% of the lter’s rated life is used, the yellow (Order)

light comes on. When 100% of the lter’s rated life is used,

the red (Replace) light comes on, and it is recommended that

you replace the lter. For models without lter status lights,

replace the lter every 6 months. Use replacement lter model

67003523-750. 2014 suggested retail price of

$44.99 U.S.A./$49.95 Canada. Prices are subject to change

without notice.

■The product is for cold water use only.

■Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after

the system. Systems certied for cyst reduction may be used

on disinfected waters that may contain lterable cysts.

■Refer to the “Water Filtration System” section for the

Manufacturer’s name and telephone number.

■Refer to the “Warranty” section for the Manufacturer’s limited

warranty.

Application Guidelines/Water Supply Parameters

Water Supply

Water Pressure

Water Temperature

Service Flow Rate

City or Well

35 - 120 psi (241 - 827 kPa)

33° - 100°F (1° - 38°C)

0.78 gpm (2.9 L/min.) @ 60 psi

System tested and certied by NSF International against NSF/ANSI Standard 42 for the

reduction of Chlorine Taste and Odor, Particulate Class I*; and against NSF/ANSI

Standard 53 for the reduction of Lead, Mercury, Atrazine, Benzene, p-Dichlorobenzene,

Carbofuran, Toxaphene, Cysts, Turbidity, Asbestos, Tetrachloroethylene and Lindane.

*Class I particle size: >0.5 to <1 um

**Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.

†These contaminants are not necessarily in your water supply Performance may vary based on local water conditions.

††Fibers greater than 10 um in length

‡Based on the use of Cryptosporidium parvum oocysts

® NSF is a registered trademark of NSF International.

Interior Water Filtration System

Model UKF8001AXX-200 Capacity 200 Gallons (757 Liters)

This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The

concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the

permissible limit for water leaving the system, as specied in NSF/ANSI Standards 42 and 53.

Substance Reduction

Aesthetic Effects

NSF Reduction

Requirements

Average

Inuent

Inuent Challenge

Concentration

Maximum

Efuent

Average

Efuent

Minimum%

Reduction

Average%

Reduction

Chlorine Taste/Odor

Particulate Class I*

50% reduction

85% reduction

2.00 mg/L

14,000,000 #/mL

2.0 mg/L ± 10%

At least

10,000 particles/mL

0.06 mg/L

370,000 #/mL**

0.050625 mg/L

196,666 #/mL

97.00%

97.40%

97.52%

99.00%

Contaminant

Reduction

NSF Reduction

Requirements

Average

Inuent

Inuent Challenge

Concentration

Maximum

Efuent

Average

Efuent

Minimum%

Reduction

Average%

Reduction

Lead: @ pH 6.5

Lead: @ pH 8.5

0.010 mg/L

0.150 mg/L†

0.15 mg/L ± 10%

< 0.001 mg/L

>99.30%

Mercury: @ pH 6.5

Mercury: @ pH 8.5

0.002 mg/L

0.006 mg/L

0.0059 mg/L

0.006 mg/L ± 10%

0.0005 mg/L

0.0018 mg/L

0.0003 mg/L

0.00073 mg/L

91.70%

69.20%

95.00%

88.10%

Benzene 0.005 mg/L 0.0133 mg/L 0.015 mg/L ± 10% 0.0005 mg/L 0.0005 mg/L 96.10% 96.30%

p-Dichlorobenzene 0.075 mg/L 0.210 mg/L 0.225 mg/L ± 10% < 0.0005 mg/L < 0.0005 mg/L >99.80% >99.80%

Carbofuran 0.040 mg/L 0.0753 mg/L 0.08 mg/L ± 10% 0.027 mg/L 0.008 mg/L 64.60% 73.45%

Toxaphene 0.003 mg/L 0.015 mg/L 0.015 ± 10% < 0.001 mg/L < 0.001 mg/L >93.3% >93.3%

Atrazine 0.003 mg/L 0.0102 mg/L 0.009 mg/L ± 10% 0.0027 mg/L 0.00105 mg/L 76.30% 89.40%

Asbestos >99% 126.5 MF/L 107 to 108 bers/L†† < 0.17 MF/L < 0.17 MF/L >99.99% >99.99%

Live Cysts ‡

Turbidity

>99.95%

0.5 NTU

122,500 #/L

10.5 NTU

50,000/L min.

11 ± 1 NTU

< 1 #/L‡

0.30 NTU

< 1 #/L‡

0.125 NTU

>99.99%

97.30%

>99.99%

98.80%

Lindane 0.0002 mg/L 0.0019 mg/L 0.002 ± 10% < 0.00016 mg/L 0.000035 mg/L 91.80% 97.90%

Tetrachloroethylene 0.005 mg/L 0.015 mg/L 0.015 mg/L ± 10% < 0.0005 mg/L < 0.0005 mg/L >96.6% >96.6%

O-Dichlorobenzene 0.6 mg/L 1.7 mg/L 1.8 mg/L ± 10% < 0.5 mg/L < 0.5 mg/L >99.9% >99.9%

Ethylbenzene 0.7 mg/L 2.2 mg/L 2.1 mg/L ± 10% 0.0048 mg/L 0.11 mg/L 99.80% 99.90%

Chlorobenzene 0.1 mg/L 2.0 mg/L 2.0 mg/L ± 10% 0.0038 mg/L 0.0008 mg/L 99.80% 99.90%

Endrin 0.002 mg/L 0.007 mg/L 0.006 mg/L ± 10% 0.0004 mg/L 0.0002 mg/L 94.30% 96.80%

Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.78 gpm (2.9 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F ± 5°F

(20°C ± 3°C).

■It is essential that operational, maintenance, and lter

replacement requirements be carried out for the product to

perform as advertised.

■The disposable water lter should be replaced at least every

6 months.

■The lter monitor system measures the amount of water that

passes through the lter and alerts you to replace the lter.

When 90% of the lter’s rated life is used, the yellow (Order)

light comes on. When 100% of the lter’s rated life is used,

the red (Replace) light comes on, and it is recommended that

you replace the lter. For models without lter status lights,

replace the lter every 6 months. Use replacement lter model

UKF8001AXX-200. 2014 suggested retail price of $44.99

U.S.A./$49.95 Canada. Prices are subject to change without

notice.

■The product is for cold water use only.

■Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after

the system. Systems certied for cyst reduction may be used

on disinfected waters that may contain lterable cysts.

■Refer to the “Water Filtration System” section for the

Manufacturer’s name and telephone number.

■Refer to the “Warranty” section for the Manufacturer’s limited

warranty.

Application Guidelines/Water Supply Parameters

Water Supply

Water Pressure

Water Temperature

Service Flow Rate

City or Well

35 - 120 psi (241 - 827 kPa)

33° - 100°F (1° - 38°C)

0.55 gpm (2.08 L/min.) @ 60 psi

System tested and certied by NSF International against NSF/ANSI Standard 42 for the reduction of

Chlorine Taste and Odor, Particulate Class I*; and against NSF/ANSI Standard 53 for the reduction

of Lead, Mercury, Atrazine, Benzene, p-Dichlorobenzene, Carbofuran, Toxaphene, Cysts, Turbidity,

Asbestos, O-Dichlorobenzene, Ethylbenzene, Chlorobenzene, Endrin, Tetrachloroethylene and Lindane.

*Class I particle size: >0.5 to <1 um

**Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.

†These contaminants are not necessarily in your water supply Performance may vary based on local water conditions.

††Fibers greater than 10 um in length

‡Based on the use of Cryptosporidium parvum oocysts

® NSF is a registered trademark of NSF International.

04/17

IF YOU NEED SERVICE:

1. Before contacting us to arrange service, please determine whether your product requires repair. Some questions can be addressed without

service. Please take a few minutes to review the Troubleshooting section of the Use and Care Guide or visit producthelp.kitchenaid.com.

2. All warranty service is provided exclusively by our authorized KitchenAid Service Providers. IntheU.S.and Canada, direct all requests for

warranty service to:

KitchenAid Customer eXperience Center

In the U.S.A., call 1-800-422-1230. In Canada, call 1-800-807-6777.

If outside the 50 United States or Canada, contact your authorized KitchenAid dealer to determine whether another warranty applies.

KITCHENAID®

REFRIGERATION

LIMITED WARRANTY

ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE

IS REQUIRED TO OBTAIN WARRANTY SERVICE.

Please have the following information available when you call the

Customer eXperience Center:

■Name, address, and telephone number

■Model number and serial number

■A clear, detailed description of the problem

■Proof of purchase, including dealer or retailer name and address

TEN YEAR LIMITED WARRANTY

WHAT IS COVERED WHAT IS NOT COVERED

ONE YEAR LIMITED WARRANTY (PARTS AND LABOR)

For one year from the date of purchase, when this major appliance is

installed, operated, and maintained according to instructions attached to or

furnished with the product, KitchenAid brand of Whirlpool Corporation or

Whirlpool Canada LP (hereafter “KitchenAid”) will pay for factory specied

replacement parts and repair labor to correct defects in materials or

workmanship that existed when this major appliance was purchased or, at

its sole discretion, replace the product. In the event of product replacement,

your appliance will be warranted for the remaining term of the original unit’s

warranty period.

SECOND THROUGH FIFTH YEAR LIMITED WARRANTY ON CAVITY

LINER AND SEALED REFRIGERATION SYSTEM (PARTS AND LABOR)

In the second through fth years from the date of original purchase, when

this major appliance is installed, operated, and maintained according to the

instructions attached to or furnished with the product, KitchenAid will pay

for factory specied replacement parts and repair labor for the following

components to correct non-cosmetic defects in materials or workmanship

in this part that prevent function of the refrigerator and that existed when

this major appliance was purchased:

■Refrigerator/freezer cavity liner if the part cracks due to defective

materials or workmanship.

■Sealed refrigeration system (includes compressor, evaporator, condenser,

dryer, and connecting tubing).

SIXTH THROUGH TENTH YEAR LIMITED WARRANTY ON SEALED

REFRIGERATION SYSTEM (PARTS ONLY—LABOR NOT INCLUDED)

In the sixth through tenth year from the date of purchase, when this major

appliance is installed, operated, and maintained according to instructions

attached to or furnished with the product, KitchenAid will pay for factory

specied replacement parts to correct defects in materials or workmanship

in the sealed refrigeration system (includes compressor, evaporator,

condenser, dryer, and connecting tubing) that existed when this major

appliance was purchased.

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED

WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

Service must be provided by a KitchenAid designated service company.

This limited warranty is valid only in the United States or Canada and

applies only when the major appliance is used in the country in which it

was purchased. This limited warranty is effective from the date of original

consumer purchase. Proof of original purchase date is required to obtain

service under this limited warranty.

1. Commercial, non-residential, or multiple-family use, or use

inconsistent with published user, operator, or installation

instructions.

2. In-home instruction on how to use your product.

3. Service to correct improper product maintenance or

installation, installation not in accordance with electrical or

plumbing codes, or correction of household electrical or

plumbing (e.g., house wiring, fuses, or water inlet hoses).

4. Consumable parts (e.g., light bulbs, batteries, air or water

lters, preservation solutions).

5. Defects or damage caused by the use of non-genuine

KitchenAid parts or accessories.

6. Damage from accident, misuse, abuse, re, oods, acts of

God, or use with products not approved by KitchenAid.

7. Repairs to parts or systems to correct product damage

or defects caused by unauthorized service, alteration, or

modication of the appliance.

8. Cosmetic damage, including scratches, dents, chips, and

other damage to the appliance nishes, unless such damage

results from defects in materials and workmanship and is

reported to KitchenAid within 30 days.

9. Discoloration, rust, or oxidation of surfaces resulting from

caustic or corrosive environments including, but not limited

to, high salt concentrations, high moisture or humidity, or

exposure to chemicals.

10. Food or medicine loss due to product failure.

11. Pickup or delivery. This product is intended for in-home repair.

12. Travel or transportation expenses for service in remote

locations where an authorized KitchenAid servicer is not

available.

13. Removal or reinstallation of inaccessible appliances or built-

in xtures (e.g., trim, decorative panels, ooring, cabinetry,

islands, countertops, drywall) that interfere with servicing,

removal, or replacement of the product.

14. Service or parts for appliances with original model/serial

numbers removed, altered, or not easily determined.

The cost of repair or replacement under these excluded

circumstances shall be borne by thecustomer.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A

PARTICULAR PURPOSE, ARE LIMITED TO TEN YEARS OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do

not allow limitations on the duration of implied warranties of merchantability or tness, so this limitation may not apply to you. This warranty

gives you specic legal rights, and you also may have other rights that vary from state to state or province to province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

KitchenAid makes no representations about the quality, durability, or need for service or repair of this major appliance other than the

representations contained in this warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes

with this major appliance, you should ask KitchenAid or your retailer about buying an extended warranty.

LIMITATION OF REMEDIES: EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

KITCHENAID SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the

exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives

you specic legal rights, and you also may have other rights that vary from state to state or province to province.

La page charge ...

KitchenAid KRBX109EBL Le manuel du propriétaire

Marque: KitchenAid

Modèle: KRBX109EBL

Catégorie: Frigos

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: KitchenAid KRBX109EBL Owner's manual
español: KitchenAid KRBX109EBL El manual del propietario