Sollae Systems SIG-5451 Manuel utilisateur

Sollae Systems

https://www.ezTCP.com

2-Port Digital Output I/O Gateway

SIG-5451 User Manual

Version 1.1

SIG-5451 User Manual Ver. 1.1

- 1 -

https://www.ezTCP.com

This symbol, found on your product or on its packaging, indicates that

this product should not be treated as household waste when you wish to

dispose of it. Instead, it should be handed over to an applicable collection

point for the recycling of electrical and electronic equipment. By ensuring

this product is disposed of correctly, you will help prevent potential negative

consequences to the environment and human health, which could otherwise be caused by

inappropriate disposal of this product. The recycling of materials will help to conserve

natural resources. For more detailed information about the recycling of this product,

please contact your local city office, household waste disposal service or the retail

store where you purchased this product.

Note:

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

SIG-5451 User Manual Ver. 1.1 
 
- 2 - 
https://www.ezTCP.com 
 
Contents 
Overview ....................................................... - 4 - 
1 Introduction ........................................................ - 4 - 
2 Features ............................................................ - 4 - 
3 Specification ....................................................... - 5 - 
4 Interface ........................................................... - 6 - 
4.1 Power .................................................................. - 6 - 
4.2 Ethernet ............................................................... - 7 - 
4.3 Digital Output Port .................................................... - 7 - 
4.4 LED .................................................................... - 8 - 
4.5 Function Button ........................................................ - 9 - 
4.6 Setup Port ............................................................. - 9 - 
Preparation ................................................... - 10 - 
1 Installing the Setting Tool ........................................ - 10 - 
2 Connecting a Product ............................................... - 10 - 
3 Searching Devices .................................................. - 10 - 
4 Logging in ......................................................... - 10 - 
Settings ...................................................... - 11 - 
1 Network ............................................................ - 11 - 
1.1 Obtain an IP address automatically ..................................... - 11 - 
1.2 Use a Static IP address................................................ - 12 - 
2 General ............................................................ - 13 - 
2.1 Comment ............................................................... - 13 - 
2.2 Digital Output ........................................................ - 13 - 
3 Security ........................................................... - 14 - 
3.1 Password .............................................................. - 14 - 
3.2 Certificate ........................................................... - 14 - 
3.3 spFinder .............................................................. - 14 - 
3.4 Client ID ............................................................. - 15 - 
Management .................................................... - 16 - 
1 Checking Status .................................................... - 16 - 
1.1 Product Information ................................................... - 16 - 
1.2 Communication Status .................................................. - 17 - 
1.3 Timeout ............................................................... - 18 - 
1.4 Copy status ........................................................... - 18 - 
2 Firmware Change .................................................... - 19 - 
2.1 Online Upgrade ........................................................ - 19 - 
2.2 Manual Upgrade ........................................................ - 20 - 
2.3 Remote Upgrade via cloud............................................... - 20 - 
3 Console ............................................................ - 21 - 

SIG-5451 User Manual Ver. 1.1

- 3 -

https://www.ezTCP.com

4.3.1 Output Tab ............................................................ - 21 -

4.3.2 FW Log Tab ............................................................ - 22 -

4.3.3 Timeout ............................................................... - 22 -

4.4 Export/Import Setting Values ....................................... - 23 -

4.5 Factory Reset ...................................................... - 24 -

5 Technical Support and Warranty ................................ - 25 -

5.1 Technical Support .................................................. - 25 -

5.2 Warranty ........................................................... - 25 -

5.2.1 Free Repair Services .................................................. - 25 -

5.2.2 Charged Repair Services................................................ - 25 -

6 Precaution and Exemption from Liability ....................... - 26 -

6.1 Precaution ......................................................... - 26 -

6.2 Exemption from Liability ........................................... - 27 -

6.2.1 English version ....................................................... - 27 -

6.2.2 French version ........................................................ - 28 -

7 Revision History .............................................. - 30 -

SIG-5451 User Manual Ver. 1.1

- 4 -

https://www.ezTCP.com

1 Overview

1.1 Introduction

SIG-5451 is an industrial I/O Gateway connected to Sollae Cloud. It is equipped

with 2 digital output ports and an Ethernet interface. Users can use this product to

control remote devices by using a web browser on your PC, tablet or smartphone.



This document presents the information related to device only. To connect the

device to Sollae Cloud, see Sollae Cloud User Guide.

1.2 Features

⚫ 2 digital output ports (Relay): Both NO and NC output

⚫ Ethernet Interface

⚫ Freely connected to Sollae Cloud via MQTT

⚫ Data is encrypted and securely transmit using TLS 1.2

⚫ Client certificate authentication for devices

⚫ Industrial temperature range (-40℃ ~ +85℃)

SIG-5451 User Manual Ver. 1.1

- 5 -

https://www.ezTCP.com

1.3 Specification

Digital Output

Output Type

Relay (Type C - NO/NC, Max DC 30V/2A with resistive load)

Number of Ports

2 ports

Network Physical Interface

Network Interface

10Base-T/100Base-TX Ethernet (RJ45)

Ethernet Speed Auto Sense

1:1 or Cross-over Cable Auto Sense

Software Functions

Protocols

IP, TCP, ICMP, DHCP, mDNS, MQTT, SSL/TLS 1.2

Network Security

Client certificate-based mutual authentication over TLS

1.2

Indicators

LED

PWR, STS, MTX, MRX, Do0, Do1

Management

spFinder

Configuration and Monitoring Tool

Access Security

Password

Dimension

Size

94mm x 57mm x 23mm

Weight

about 68g

Operating Environment

Input Voltage

DC5V±0.5V

Protection

Reverse Voltage Protection / Surge Protection

Current Consumption

typically, 210mA

Operating Temperature

-40℃ ~ +85℃

Storage Temperature

-40℃ ~ +85℃

Certificate

KC

Registration (KN 32, KN 35)

CE

EMC 2014/30/EU, RoHS 2011/65/EU

FCC

FCC Part 15 Subpart B, Class A

Table 1-1 Specification

SIG-5451 User Manual Ver. 1.1

- 6 -

https://www.ezTCP.com

1.4 Interface

Figure 1-1 Interface

1.4.1 Power

SIG-5451 requires DC5V power supply whose specification is as follows:

Figure 1-2 Power

SIG-5451 User Manual Ver. 1.1

- 7 -

https://www.ezTCP.com

1.4.2 Ethernet

SIG-5451 provides 10/100Mbps Ethernet. The pin assignment is as follows:

Figure 1-3 Ethernet

1.4.3 Digital Output Port

This port is interfaced with a 3.5mm pitch 6-pole terminal block.

Figure 1-4 Digital output port

⚫ Port Specification

Division

Value

Number of ports

2

Max. Allowed Current

at DC 30V

Normal Open

5A

Normal Close

1A

Table 1-2 Port Specification



The port specifications are for resistive loads. For capacitive loads such as

SMPS and inductive loads such as motors, the current under normal operation

should be about 10 ~ 20% of the maximum allowed current.

⚫ Port Specification

State

NO Operation

NC Operation

LOW

NOT Connected to C0/C1

Connected to C0/C1

HIGH

Connected to C0/C1

NOT Connected to C0/C1

Table 1-3 Port Operation

SIG-5451 User Manual Ver. 1.1

- 8 -

https://www.ezTCP.com

1.4.4 LED

SIG-5451 provides 8 LEDs.

Figure 1-5 4 LED operations according to each state are as follows:

When the supplied power is stable: PWR

When the supplied power is NOT stable: PWR

When the script is running: RUN

When a network is not connected: LINK

When a network is connected: LINK

When a MQTT connection is NOT established: MTX & MRX

When sending data to the cloud: MTX

When receiving data (command) from cloud: MRX

When the output port is LOW: Do0 & Do1

When the output port is HIGH: Do0 & Do1

SIG-5451 User Manual Ver. 1.1

- 9 -

https://www.ezTCP.com

1.4.5 Function Button

This button is used to implement a factory reset.

1.4.6 Setup Port

This port is used for making a connection with a PC via USB cable.

SIG-5451 User Manual Ver. 1.1

- 10 -

https://www.ezTCP.com

2 Preparation

2.1 Installing the Setting Tool

You need a Windows program which is called spFinder to use this product. Download

the program on our web site and install it on your PC.

Functions of the spFinder are as follows:

⚫ Searching products connected via network and USB

⚫ Setting products

⚫ Monitoring status of products

2.2 Connecting a Product

Connect a product with your PC via a LAN cable or a USB cable. In the case of

using a LAN cable, note that your PC and the product should be on the same local

area network.

2.3 Searching Devices

Run spFinder on your PC and press the search button. If you select the product

found, the setup menu appears on the right.

2.4 Logging in

Before accessing the searched product, you need to log in first. The default ID

and password are as follows:

Division

Default Values

ID

sig-5451

Password

sig-5451

Table 2-1 The default values of ID and password



If you search the product via network and it has the default value for a password,

spFinder automatically processes the login.

SIG-5451 User Manual Ver. 1.1

- 11 -

https://www.ezTCP.com

3 Settings

3.1 Network

3.1.1 Obtain an IP address automatically

This product can automatically obtain an IP address by DHCP. A DHCP server is

required to use this.

Figure 3-1 Obtain an IP address automatically

⚫ Select the [Obtain an IP address automatically].

⚫ Check the [Obtain DNS server address automatically] and click the [Save]

button.

SIG-5451 User Manual Ver. 1.1

- 12 -

https://www.ezTCP.com

3.1.2 Use a Static IP address

You can set a static IP address to this product.

Figure 3-2 Use a static IP address

⚫ Select the [Use static IP address].

⚫ Set the [Local IP address], [Subnet mask], [Gateway IP address] and [DNS IP

address].

⚫ Click the [Save] button.

SIG-5451 User Manual Ver. 1.1

- 13 -

https://www.ezTCP.com

3.2 General

Figure 3-3 General

3.2.1 Comment

This setting is for storing the product description. The maximum setting size of

this item is 32 bytes. We can add information such as: When a device is registered

to the cloud, this field will be used as the default device description on Sollae

Cloud.

3.2.2 Digital Output

⚫ Fail Safe Mode

This item is to enable/disable the Fail-Safe function. When the MQTT

connection to Sollae Cloud is lost, if Fail-Safe is enabled, the output port

is set to LOW, otherwise the output port keeps the current state.



The fail-safe mode can be set via spFinder only. It is impossible to set via

Sollae Cloud.



User Interface and other features configurations can only be set via Sollae Cloud.

SIG-5451 User Manual Ver. 1.1

- 14 -

https://www.ezTCP.com

3.3 Security

Figure 3-4 Security

3.3.1 Password

Both ID and password are required to access this product. Note that changing the

default password to another is highly recommended for security. The password should

be longer than 8 characters.

⚫ Input a password to use to [Password] and [Retype password].

⚫ Click the [Save] button.

3.3.2 Certificate

All TLS certificates were preloaded to the device, please ignore this part.

3.3.3 spFinder

These items are related to spFinder use.

⚫ Local search

If this item is not checked, you will not be able to search for or connect to

the product on your local network. This item can be set only when the product

is connected via USB.

⚫ Network connection

If this item is not checked, the product cannot be searched on the local

network and the product cannot be connected on the local or remote network.

This item can be set only when the product is connected via USB.

SIG-5451 User Manual Ver. 1.1

- 15 -

https://www.ezTCP.com

⚫ Remote access

If this item is checked, the product can be connected from the remote network.

For security, this item is unchecked by default.

3.3.4 Client ID

The Unique ID which is used to register the device under your account in Sollae

Cloud. See more detail on Sollae Cloud.

SIG-5451 User Manual Ver. 1.1

- 16 -

https://www.ezTCP.com

4 Management

4.1 Checking Status

This is a function to view the current status of the product. Information in the

[Status] window is automatically updated every second. After searching and

connecting the product with spFinder, press the [Status] button to display this

window. When you open this window, the spFinder connects to the product and keeps

the connection until you close the window or time out. While the connection is

maintained, other hosts cannot access the product using the spFinder.

4.1.1 Product Information

⚫ Product Information Window

This area shows some major information of your product.

Figure 4-1 Product Information Window

⚫ Product Information List

Item

Description

Product name

Pkgware

Model name, package version, Firmware version

File name

Uptime

Elapsed time since it boots up (day / hour:min:sec)

IPv4

Assigned IPv4 address

Subnet

Assigned subnet mask

Gateway

Assigned gateway IP address

DNS

Assigned DNS server IP address

Table 4-1 Product Information List

SIG-5451 User Manual Ver. 1.1

- 17 -

https://www.ezTCP.com

4.1.2 Communication Status

⚫ Communication Status Window

This area shows some communication status of your product. This area is

refreshed every second.

Figure 4-2 Communication Status Window

⚫ REGISTRATION STATE

The registration state indicates whether the device is registered on Sollae

Cloud under an account or not.

Status

Description

checking

Checking the registration status

unregistered

The device is unregistered under any account

registered

The device was registered under an account

Table 4-2 REGISTRATION STATE

⚫ SSL STATE

SSL/TLS connection state.

Status

Description

SSL CLOSED

Disconnected

SSL CONNECTING

Connecting

SSL CLOSING

Closing connection

SSL CONNECTED

Connected

Table 4-3 SSL STATE

SIG-5451 User Manual Ver. 1.1

- 18 -

https://www.ezTCP.com

⚫ DEVICE STATE

The device operation state.

Status

STARTING

UPDATING INFORMATION TO CLOUD

FAILED TO UPDATE INFORMATION TO CLOUD

DEVICE IS UNREGISTERED TO AN USER

CONNECTING MQTT SERVER

MQTT CLOSED

MQTT CONNECTED TO CLOUD

MQTT PING TO CLOUD

DELAYING BEFORE RECONNECTING

UPGRADING PKGWARE

CONFIGURING DEVICE

APPENV FAILED

CERTS FAILED

Table 4-4 DEVICE STATE

⚫ DIGITAL OUTPUT

Shows the state of digital output ports.

Item

Description

DO0~1

Current state of each digital output port

Table 4-5 DIGITAL OUTPUT

4.1.3 Timeout

This is the timeout display function that appears in the upper right of the status

window. When this time reaches zero, the connection between spFinder and the product

is lost. The initial value is 30 minutes. If you move the mouse pointer in the

internal area of the status window, the timer is reset to the initial value again.

4.1.4 Copy status

Clicking this button copies all information displayed in the current status window

to the clipboard.

SIG-5451 User Manual Ver. 1.1

- 19 -

https://www.ezTCP.com

4.2 Firmware Change

New firmware can be released when adding functions or fixing bugs. If you are

using old firmware, you can upgrade it to the latest version. Firmware can be

upgraded online or manually via spFinder, or remotely via Cloud.

4.2.1 Online Upgrade

If you can access to the Internet by your PC, the Firmware can be upgraded online.

Figure 4-3 Online Upgrade

⚫ Search and Connect to your product by spFinder.

⚫ Click [Advanced] > [Firmware change] menu.

⚫ Click [Upgrade] button selecting [Automatic online upgrade] menu.

La page charge ...

Sollae Systems SIG-5451 Manuel utilisateur

Sollae Systems SIG-5451 Manuel utilisateur

dans d''autres langues