Yamaha KX-E100 Le manuel du propriétaire
- Catégorie
- Lecteurs de cassettes
- Taper
- Le manuel du propriétaire
BG
KX-E100
Natural Sound Stereo Cassette Deck
Platine Cassette Stéréo
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
E-2
Dolby noise reduction is extremely effective in reducing undesirable background hiss on tapes. This unit incorporates
Dolby B/C type noise reduction systems. The conventional Dolby B-type noise reduction provides approximately 8 dB
improvement in S/N ratio and C-type adds additional improvement over the B-type. The noise reduction is applied to both
recording and playback; be sure that the same noise reduction is used on recording and playback. Pressing DOLBY NR
switches between Dolby B, C and OFF.
Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation.
“DOLBY” and the double-D symbol
are trademarks of Dolby Laboratories Licensing Corporation.
INTRODUCTION
Thank you for purchasing this YAMAHA product. We hope it will give you many years of trouble-free enjoyment. For the
best performance, read this manual carefully. It will guide you in operating your YAMAHA product.
ENGLISH
FEATURES
• High Performance Auto-Reverse Tape Deck
• Dolby B/C Type Noise Reduction
• Applicable to Metal Tape Recording
CONTENTS
PRECAUTIONS .................................................. 3
NAMES OF CONTROLS AND FUNCTIONS
Front panel............................................................ 4
Display ................................................................. 4
GETTING STARTED
Connecting the unit to the receiver RX-E100 and
CD player CDX-E100 .......................................... 5
SUPPLIED ACCESSORIES
This unit, KX-E100 is one of the YAMAHA E100 series components.
• RCA Pin Cable x2 • System Control Cable x1
OPERATIONS
Playback ............................................................... 6
Recording ............................................................. 7
ADDITIONAL INFORMATION
Troubleshooting.................................................... 8
Notes about cassette tapes .................................... 9
Specifications ....................................................... 9
• Synchronized Recording
• Automatic Dubbing Function
Dolby B/C Type Noise Reduction
• REC/PLAY Level Meters with Peak Hold Function
E-3
English
PRECAUTIONS: READ THIS BEFORE OPERATING THE UNIT
CAUTIONS
•
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
• Install your unit in a well ventilated, cool, dry, clean
place – away from windows, heat sources, vibration,
dust, moisture, or cold. To avoid humming sounds,
locate the unit away from other electrical appliances,
motors, and transformers. To prevent fire or
electrical shock, do not expose to rain and water.
• Do not operate the unit upside-down. It may
overheat, possibly causing damage.
• Never open the cabinet. If something drops into the
set, contact your dealer.
• Do not use force on switches, knobs or cords.
• When not planning to use this unit for long periods
of time (i.e., vacation, etc.), disconnect the AC power
plug from the wall outlet.
• Grounding or polarization – Precautions should be
taken so that the grounding or polarization of the unit
is not defeated.
• Do not clean the unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
• Be sure to read the “Troubleshooting” section on
common operating errors before concluding that
your unit is faulty.
• Do not place another component on top of this unit,
as damage or discoloration on the surface of the unit
may result.
•
To prevent damage by lightning, disconnect the power
cord from the wall outlet during an electrical storm.
• When disconnecting the power cord from the wall
outlet, grasp the plug; do not pull the cord.
• Do not plug the AC power cord to the wall outlet
before you finish all connections.
• The voltage to be used must be the same as that
specified on this unit. Using this unit with a higher
voltage than that which is specified is dangerous and
may result in a fire or other type of accident causing
damage. YAMAHA will not be held responsible for
any damage resulting from use of this unit with a
voltage other than that which is specified.
• Never allow metallic items (e. g. screwdrivers, tools,
etc.) to come near the record/playback head
assembly. Doing so may not only scratch or damage
the head’s mirror-smooth finish, but also change the
magnetic characteristics of the heads, causing a
deterioration in reproduction quality.
• Although the record/playback head used in this unit
is a high quality head with outstanding reproduction
characteristics, it can become dirty through the use of
old tapes or from dust accumulation over time.
This can have a serious effect on reproduction
quality.
Clean the heads regularly with one of the commonly
available head cleaners or with an appropriate
cleaning solution.
NOTE
Please check the copyright laws in your country to
record from records, compact discs, radio, etc.
Recording of copyright material may infringe
copyright laws.
This unit is not disconnected from the AC power
source as long as it is connected to the wall outlet,
even if this unit itself is turned off. This state is
called the standby mode. In this state, this unit is
designed to consume a very small quantity of power.
IMPORTANT:
The wires in the mains lead are coloured in accordance
with the following code:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows: The wire which is coloured BLUE
must be connected to the terminal which is marked
with the letter N or coloured BLACK. The wire which
is coloured BROWN must be connected to the terminal
which is marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth
terminal of the three pin plug.
For U.K. customers
If the socket outlets in the home are not suitable for the
plug supplied with this appliance, it should be cut off and
an appropriate 3 pin plug fitted. For details, refer to the
instructions described above.
SPECIAL INSTRUCTIONS FOR U.K. MODEL
Note: The plug severed from the mains lead must be
destroyed, as a plug with bared flexible cord is hazardous
if engaged in a live socket outlet.
E-4
NAMES OF CONTROLS AND FUNCTIONS
Front panel
~ STANDBY/ON (p.6)
Ÿ COUNTER RESET (p.7)
! MODE (p.6)
⁄ Multi-information display (p.4)
@ REC/PAUSE (p.7)
¤ DOLBY NR (p.2)
# REC LEVEL (p.7)
‹ ! / ⁄ (Rewind, Music search backward/
Fast-forward, Music search forward) (p.6)
$ DIRECTION @# (p.6)
› # (Play) (p.6)
% & (Stop) (p.6)
fi (Open/Close) (p.6)
^ Tape tray (p.6)
Display
~ Counter display
Ÿ Reverse mode indicator
! Dolby Noise Reduction indicator
⁄ Direction indicator
@ REC indicator
-30 20 15 10 8 6 4 2 0 2 4 6 +db
L
R
SEARCH
B C REC PLAY
MAX
MIN
REC LEVEL
DOLBY NR
MODE
COUNTER
RESET
DIRECTION
NATURAL SOUND STEREO CASSETTE DECK KX-E100
STANDBY/ON
REC/
PAUSE
DOLBY B-C NR
¤ Music SEARCH indicator
# PLAY indicator
‹ Rewind/Fast-forward indicator
$ REC/PLAY level indicator
E-5
English
L
R
SYSTEM
CONNECTOR
DIGITAL
OPTICAL
ANALOG
OUT
OUT
STEP
FREQUENCY
D
L
R
C
AB E
E
LR
L
R
SUBWOOFER
OUT
OUT IN IN
MD
CD
AUX
TAPE
6 Ω MIN./SPEAKER
SPEAKERS
FM ANT GND AM ANT
75 Ω UNBAL
L
R
SYSTEM
CONNECTOR
OUTIN
BA
SYSTEM
CONNECTOR
Connecting the unit to the receiver RX-E100 and
CD player CDX-E100
Never plug the AC power cord into the wall outlet until all other connections are completed.
Follow the steps as shown below to connect the unit to the receiver (RX-E100), CD player (CDX-E100), and MD recorder
(MDX-E100) using the supplied accessories.
1 Connect Å to Å, and ı to ı using the RCA pin cables.
Insert the plugs into the jacks of the same colour.
• The two RCA pin cables are the same, so you can connect Å or ı using either cord.
2 Connect the unit and the CDX-E100 (or MDX-E100) with the system control cable.
3 Connect the AC power cord to AC OUTLET of CDX-E100 (or MDX-E100) (except for U.K. model).
GETTING STARTED
1
2
3
To wall outlet
To RX-E100
To CDX-E100
System control cable
RCA pin cables
<CDX-E100>
<KX-E100>
<RX-E100>
E-6
OPERATIONS
1 Press STANDBY/ON to turn on this unit and also
RX-E100.
2 Set RX-E100 to cassette deck function mode.
3 Press to open the tape tray and place a recorded
tape on the tray.
4 Press to close the tape tray.
5 Press MODE to select the reverse mode.
Each time you press MODE, the reverse mode
changes and the corresponding mode indicator lights
up as follows:
: One side of the tape is played back.
: Both sides of the tape are played back.
: Both sides of the tape are played back up to 8
times continuously.
Playback
You can use any type of tape, since the unit automatically
detects the tape type.
6 Press DIRECTION to change the direction of the
tape.
• If you place the tape on the tray with side A
upward, # indicates playing side A and @
indicates playing side B.
7 Select the noise reduction type using DOLBY NR if
necessary.
8 Press # to start play.
To stop play
Press &.
To eject a tape
Press to open the tape tray and remove the tape from
the tray.
To adjust the volume level
Use the volume control of RX-E100.
To fast-forward or rewind the tape
Press ⁄ or ! to fast-forward or rewind the tape
during stop mode.
To search for the beginning of a
selection
Press ⁄ or ! to search for the beginning of the next
or current selection during play mode.
Notes
• The blank interval between selections must be at least 4
seconds long.
• The search function may not operate properly with tapes
recorded at a low recording level or which have excessive
noise.
• When you play the beginning part or end part of the tape, the
search function may not work correctly.
Tape Tray
&#
! / ⁄ DIRECTIONMODESTANDBY/
ON
MAX
MIN
REC LEVEL
DOLBY NR
REC/
PAUSE
MODE
COUNTER
RESET
DIRECTION
NATURAL SOUND STEREO CASSETTE DECK KX-E100
STANDBY/ON
DOLBY B-C NR
DOLBY NR
E-7
English
OPERATIONS
1 Set the recording mode of RX-E100 and other
components.
2 Press MODE to select the reverse mode.
Each time you press MODE, the reverse mode
changes and the corresponding mode indicator lights
up as follows:
: One side of the tape is recorded.
: Both sides of the tape are recorded.
3 Press DIRECTION to change the direction of the
tape.
• If you place the tape on the tray with side A
upward, # indicates recording side A and @
indicates recording side B.
4 Press REC/PAUSE.
The unit turns into standby mode for recording and
the REC indicator flashes.
5 Adjust the recording level by turning REC LEVEL.
For the best results, play the loudest passage of the
source to be recorded and watch the recording level
meter in the display. Adjust REC LEVEL so that the
highest peak causes the +2 dB level indicators to
flicker.
When recording a CD, use Peak Level Search on
CDX-E100 for the optimum adjustment.
6 Select the noise reduction type using DOLBY NR if
necessary.
7 Press #.
MAX
MIN
REC LEVEL
DOLBY NR
REC/
PAUSE
MODE
COUNTER
RESET
DIRECTION
NATURAL SOUND STEREO CASSETTE DECK KX-E100
STANDBY/ON
DOLBY B-C NR
8 Start playing the source component.
• Synchronized start is possible if you have
connected the CD player, CDX-E100 or MD
recorder, MDX-E100 to this unit. Press ^ on
MDX-E100 or CDX-E100 after step 6. Recording
begins automatically.
To pause recording
Press REC/PAUSE.
To resume recording, press #.
To stop recording
Press &.
Note
• When you record on @ direction of the tape, the unit stops
recording after recording the side of the tape regardless of the
reverse mode setting in step 2.
The tape counter
The tape counter is useful for searching and locating a
certain point on the tape. Pressing COUNTER RESET
will reset the tape counter to “0000”.
Recording
COUNTER RESET
REC/PAUSEMODE REC LEVEL
DOLBY NR DIRECTION
E-8
ADDITIONAL INFORMATION
If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the
simple measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the
power cord and contact your authorized YAMAHA dealer or service center for help. When taking the service, the RX-E100
/CDX-E100 may be needed. For details, contact your authorized YAMAHA dealer or service center.
Troubleshooting
There is an influence of strong external
noise (lightning, excessive static
electricity, etc.) or a misoperation was
performed while using the unit.
Slack tape wrapped around pinch roller.
Erasure prevention tab is broken off.
Head is dirty.
Head is dirty.
Tape is worn.
Tape encoded with DOLBY NR B/C is
played back with the unit’s DOLBY NR
OFF or vice versa.
Tape encoded with DOLBY NR B is
played back with the unit’s DOLBY NR C
or vice versa.
Head is dirty.
Head is dirty.
Head has become magnetized.
Tape is worn.
Slack tape coming out of cassette shell.
Tape is worn.
System cable is not connected.
Silent gaps between tracks are too short.
Excessively soft passages in the middle of
selections.
Conversation, or noise, etc. is recorded.
Turn the unit off and disconnect the AC power
cord from the wall outlet. After about 30 seconds
have passed, connect the power and try again.
Take up slack with a pencil before using.
Replace tape or cover erasure prevention hole with
adhesive tape.
Clean heads.
Clean heads.
Replace the tape.
Select an appropriate DOLBY NR type. The same
noise reduction type should be used both on
recording and playback.
Clean heads.
Clean heads.
Demagnetize heads with head eraser.
Replace the tape.
Take up slack by turning reels with a pencil.
Replace the tape.
Connect the unit and the RX-E100 / CDX-E100
with the system cable firmly.
The function of searching for the beginning of a
desired track does not operate unless the silent
gaps between tracks are at least four seconds long.
The unit does not work normally.
Tape does not move during
playback or recording.
Cannot record.
Sound is distorted or fades out.
Poor sound quality
Stereo balance is poor.
Excessive noise
Tape travel stops in middle of
playback or recording.
The CD synchronized recording
function does not work.
Cannot search for the beginning of
desired track of the tape
SYMPTOM CAUSE REMEDY
E-9
English
ADDITIONAL INFORMATION
Cassette tapes
• YAMAHA does not recommend the use of 120 minute length cassettes since the extreme thinness of the tape makes them
susceptible to mechanical and recording problems.
• Since the unit automatically detects the tape type, you can use any type of tape.
Notes about cassette tapes
For side A
For side B
Protecting your recordings
• Tapes have removable tabs, which prevent accidental
recording or erasing from taking place. Removing the
tab on the top left protects the side facing you from
erasure. Cover the tab holes with adhesive tape to erase
or record again.
Taking up slack in the tape
• Before loading a tape on the tray, tighten the slack
portion of tape with a pen or pencil.
Maintenance
• Dirty heads, capstans, and pinch rollers can cause poor sound and tape jams. Clean these parts with a commercially
available cleaning tape.
Specifications
Type ..................................................Auto reverse stereo cassette deck
Frequency Response (–20 dB)
Type 1 (Normal) ..................................................... 30 to 15,000 Hz
Type 2 (High).......................................................... 30 to 16,000 Hz
Type 4 (Metal) ........................................................ 30 to 18,000 Hz
Wow and Flutter .......................................................... 0.09%, W.RMS
Signal-to-Noise Ratio ..................................... 58 dB (Dolby NR OFF)
66 dB (Dolby B NR ON)
74 dB (Dolby C NR ON)
Harmonic Distortion ..................................................................... 1.0%
General
Power supply
[U.S.A. and Canada models] ................................AC 120 V, 60 Hz
[Australia model] ..................................................AC 240 V, 50 Hz
[U.K. and Europe models] ....................................AC 230 V, 50 Hz
[General model] ....................... AC 110~120/220~240 V, 50/60 Hz
Power consumption ...................................................................... 12 W
Dimensions (W x H x D)....................................... 217 x 88 x 293 mm
Weight .........................................................................................3.0 kg
Accessories ..............................................................RCA Pin Cable x2
System Control Cable
Specifications are subject to change without notice.
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Printed in Malaysia V423640
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
Yamaha KX-E100 Le manuel du propriétaire
- Catégorie
- Lecteurs de cassettes
- Taper
- Le manuel du propriétaire
dans d''autres langues
- italiano: Yamaha KX-E100 Manuale del proprietario
- English: Yamaha KX-E100 Owner's manual
- Deutsch: Yamaha KX-E100 Bedienungsanleitung
- Nederlands: Yamaha KX-E100 de handleiding
- dansk: Yamaha KX-E100 Brugervejledning
- svenska: Yamaha KX-E100 Bruksanvisning
- Türkçe: Yamaha KX-E100 El kitabı
- română: Yamaha KX-E100 Manualul proprietarului