Bosch Benchmark B18IF900SP Guide d'installation

en Installation instructions

fr Instructions d‘installation

es Instrucciones de instalación

B18IF800SP

B30IR800SP

2

en Table of Contents 3

fr Table des matières 29

es Índice 55

en-us

3

en Table of Contents

enOperating instructions

Important Safety Instructions ..................................... 4

IMPORTANT .................................................................... 4

General............................................................................. 4

Definition .......................................................................... 4

Installation options............................................................ 5

Individual appliance ....................................................... 5

Side-by-Side..................................................................... 5

Individual appliances with partition............................. 5

Individual appliance at the end of the kitchen.......... 5

Installation .................................................................... 6

Installation room ............................................................. 6

Climatic classes.............................................................. 6

Stable installation ........................................................... 6

Installation niche............................................................. 6

Furniture ........................................................................... 6

Floor.................................................................................. 6

Aligning the appliance................................................... 6

Connecting the power.................................................. 7

Connecting the water................................................... 7

Dimensions of the installation niche.......................... 8

Required accessories and tools ................................. 9

Supplied accessories ................................................... 9

Optional accessories .................................................... 9

Other required accessories ......................................... 9

Miscellaneous ................................................................ 9

Tools ................................................................................ 9

Installation instructions............................................. 10

1. Checking the installation niche ........................ 10

2. Removing the packaging .................................. 10

3. Transport of the appliance ................................ 11

4. Installation preparation ....................................... 11

5. Special installation .............................................. 11

1. Attaching the anti-tip-brackets ................. 12

2. Attaching an alternative anti-tip device .. 13

3. Attaching an edge protection .................. 13

1. Pushing the appliance into

the installation niche ................................. 14

2. Aligning the appliance in

the installation niche ................................. 15

3. Attaching the appliance to

the installation niche................................... 16

1. Attaching the toe kick panel .................... 17

2. Aligning the base panel ........................... 17

3. Switching the appliance ON .................... 18

4. Preparing the door panels ....................... 18

5. Loading the appliance door .................... 18

6. Removing the installation support part . 18

7. Attaching the adjusting rail to

the door panel ............................................ 18

8. Attaching the fixation strips

to the door panel ....................................... 19

9. Attaching the door panel .......................... 20

10. Attaching the lower bracket ..................... 21

11. Attaching the strips ................................... 22

12. Mounting the air separator ...................... 22

13. Adjusting the door spring ........................ 22

Special installation..................................................... 23

Changing over the door hinges...................... 23

Removing/changing over the sealing mat ... 26

Side-by-Side installation ................................... 26

Preparing to connect the water ...................... 28

Connecting the water to the appliance ......... 28

Adjusting the door opening angle.................. 28

 Important Safety Instructions

READ AND SAVE THESE INSTRUCTIONS!

en-us

4

,PSRUWDQW6DIHW\,QVWUXFWLRQV

These mounting instructions are designed to help you

install your new appliance.

The manufacturer cannot be held liable for mounting

which has been improperly carried out. We recommend

that you allow a qualified specialist to set up and switch

the appliance on for the first time.

Following all information and keeping to the instructions

are preconditions for mounting and switching the

appliance on safely for the first time.

Keep the mounting instructions safe for use later on.

Before setting up and switching the appliance on for

the first time, read the mounting instructions fully and

thoroughly.

 WARNING:

These appliances are top-heavy and must be

secured to prevent the possibility of tipping

forward.

Anti-tip protection is required.

Keep doors closed until the appliance is

completely installed and secured per installation

instructions.

Due to the weight and size of this appliance, and

to reduce the risk of personal injury or damage

to the product – TWO PEOPLE ARE REQUIRED

FOR PROPER INSTALLATION.

This appliance must be properly grounded.

See chapter “Connecting the power”.

Use this appliance only for its intended purpose.

Immediately repair or replace electric service

cords that become frayed or damaged.

Unplug the appliance or switch off the fuse

before cleaning or making repairs.

Repairs should be made by a qualified service

technician.

 CAUTION:

Installation of this appliance requires basic

mechanical, carpentry and plumbing skills.

Proper installation is the responsibility of the

installer.

Product failure due to improper installation is not

covered under the Appliance Warranty.

See the Owner's Manual for warranty information.

IMPORTANT

Save these instructions for local inspector's use.

Observe all governing codes and ordinances.

Note to Installer – Be sure to leave these instructions

with the Consumer.

Note to Consumer – Keep these instructions with your

Owner's Manual for future reference.

General

These installation instructions are intended for use by

qualified installers. All connections for water, electrical

power and grounding must comply with local codes

and ordinances and be made by licensed personnel

when required. In the absence of a local code:

ʋ In the U.S.A., in accordance with the National

Electric Code, ANSI/NFPA70 – latest edition/State

and Municipal codes and/or local codes.

ʋ In Canada, in accordance with the Canadian

Electric Code C22.1 – latest edition/Provincial

and Municipal codes and/or local codes.

Note:

This is used to draw the user's attention to something in

particular.

Definition

 WARNING:

This indicates that serious injury or death may

result due to non-observance of this warning.

 CAUTION:

This indicates that minor or moderately severe

injury may result due to non-observance of this

warning.

en-us

5

Installation options

There are many different installation options.

These are limited only by the design of the kitchen.

See also “Kitchen Design Quick Reference”.

Individual appliance

Side-by-Side

If two appliances are set up next to each other, a

sealing kit for Side-by-Side combination should be used

in order to guarantee a stable connection.

For further information see chapter “Required

accessories and tools”.

Individual appliances with partition

ʋ When dimensioning the partition for model 4, note

the thickness of the door panels to prevent

damage if the doors are opened at the same time.

ʋ Use the Heater Kit for Side-by-Side Installation if

the gap between the appliances is less than 6"

(160 mm).

ʋ See chapter “Required accessories and tools”,

section “Optional accessories”.

ʋ Minimum thickness of the partition

5

/

8

" (16 mm).

Individual appliance at the end of the

kitchen

If one side of the appliance is visible, a side panel must

be used.

The side panel must be connected firmly to the wall, the

floor and overhead cabinet/fixtures before the

appliance is placed in the installation niche.

The dimensions of the side panel are taken from the

opposite installation niche wall. During installation

ensure that the installation niche is square and the

proper size.

en-us

6

Installation

 WARNING:

Do not install the appliance:

ʋ outdoors,

ʋ in an environment with dripping water,

ʋ in rooms which are less than 32 °F (0 °C).

ʋ A fully-loaded appliance is very heavy.

Installation room

The appliance should be installed in a dry, well

ventilated space.

The location should not be exposed to the direct

sunlight and should not lie next to a source of heat

such as a cooker or a radiator etc. If installation next to

a source of heat cannot be avoided, either a suitable

insulating plate should be used or you should keep to

the following minimum distances:

ʋ 1

1

/

4

" (3 cm) to electric or gas cookers.

ʋ 12" (30 cm) to an oil or coal-fired cooker.

The floor of the installation location must not give way; if

required, reinforce floor. To ensure that the ice maker

functions correctly, the appliance must be upright.

Climatic classes

The climate class can be found on the rating plate.

The climate class indicates within which ambient

temperatures the appliance can be operated.

Stable installation

The appliance is very heavy and has a tendency to tilt

forwards when the appliance door is opened.

The appliance must not be switched on until there is no

possibility of the appliance tilting over.

The safest method of installing the appliance in a stable

position is to use the supplied anti-tilt brackets.

If the installation niche is adequately stable and the

appliance can be attached securely to the upper and

side walls of the niche, it may be possible to dispense

with the anti-tilt brackets. A prerequisite for this is

always a firm connection between the niche and back

wall!

In the case of doubt, the help of architect or specialist

builder should be enlisted.

Installation niche

It is important to keep to the stated dimensions of the

installation niche with a view to trouble-free fitting, and

the subsequent appearance of the kitchen furniture

frontage.

Special care should be taken that the niche has right

angles. The side walls should not exhibit areas that

stick out, projections or unevenness.

You should determine the right angles of the installation

niche with appropriate means, e.g. by measuring

diagonally and by using a spirit level.

The side walls and the upper end of the installation

niche must be at least

5

/

8

" (16 mm) thick.

Furniture

The new appliance is screwed down tightly using parts

of the cabinet and the upper cabinet.

Care should therefore be taken, that all upper cabinets

to which something has been fastened are securely

connected to the subsurface or wall by appropriate

means.

The minimum thickness of the base should be a

minimum of

3

/

4

" (19 mm).

Floor

The subsurface must be level and even in order to

ensure that the appliance is securely installed and

works correctly.

The subsurface must be made from a hard, non-flexible

material.

The floor of the installation space must have the same

height as the rest of the space.

On account of the weight of a fully-laden appliance, it is

necessary to have a bearing subsurface. In the case of

doubt, the help of architect or specialist builder should

be enlisted.

Aligning the appliance

To ensure that the appliance functions correctly, it must

be levelled properly.

If the appliance is not level, water may flow out of the

ice maker, ice cubes may be irregular or the doors may

not close properly.

Refrigerator 30" approx. 1110 Ibs/500 kg

Freezer 18" approx. 560 Ibs/250 kg

Climatic class Permitted ambient temperature

SN 50 °F to 90 °F (+10 °C to 32 °C)

N 61 °F to 90 °F (+16 °C to 32 °C)

ST 61 °F to 100 °F (+16 °C to 38 °C)

T 61 °F to 110 °F (+16 °C to 43 °C)

en-us

7

Connecting the power

 WARNING:

ʋ Avoid the risk of an electric shock!

ʋ Insert into a grounded 3-phase socket.

Never remove grounding phase. Do not use

any adapters. Do not use any extension

cables.

ʋ Non-compliance with these instructions may

result in death, fire or an electric shock.

Improper connection of the protective

conductor may result in an electric shock. If

you are in doubt whether the appliance has

been grounded properly, have the appliance

tested by a qualified electrician or service

technician.

The socket must be near the appliance and also freely

accessible following installation of the appliance.

The appliance complies with protection class I.

Connect the appliance to 115 V/60 Hz alternating

current via a correctly installed socket with protective

conductor. The socket must be fused with a 10 to 16 A

fuse.

The appliance comes with a UL registered 3-wire power

cord. The appliance requires a 3-pole socket. Please

observe the following table with regard to this:

(*) incl. Ice Maker

Check on the rating plate whether the indicated voltage

and current type correspond with the values of your

power supply. The location of the rating plate can be

found in the chapter “Customer service”.

 WARNING:

Never connect the appliance to electronic energy

saver plugs. Our appliances can be used with

mains and sine-controlled inverters. Mains-

controlled inverters are used for photovoltaic

systems which are connected directly to the

national grid. Sine-controlled inverters must be

used for isolated applications (e.g. on ships or in

mountain lodges) which are not connected

directly to the national grid.

Connecting the water

 CAUTION:

Only connect the appliance to drinking water!

The water may be connected only by a competent fitter

according to the local regulations of the appropriate

water supply company.

A cold water connection is necessary for operating the

automatic ice maker. The water pressure must be

between 25 and 120 p.s.i. (1,72 and 8,25 bar).

The installation must correspond to the local plumbing

regulations.

A separate shut-off valve should be installed in the cold

water inflow. The shut-off valve should not be located

behind the appliance. It is recommended that you

mount the shut-off valve directly next to the appliance or

at another place which is easily accessible. When

installing the water connection, pay attention to the

permissible installation area for the water mains.

For connection to the drinking water mains use only

water pipes which are suitable for drinking water.

Observe national regulations and the connection

conditions of the local water supply companies.

When installing the water connection, observe the

permitted installation areas for the pipe. For the

permitted installation areas and dimensions see

“Dimensions of the installation niche”.

Maximum outer diameter of the water pipe

(without fittings):

3

/

8

" (9.5 mm).

Appliance Maximum Simultaneous Load

Refrigerator 30" 2.0 Ampere

Freezer 18" (*) 3.5 Ampere

en-us

8

Dimensions of the installation niche

Legend:

X Y

18"

(457 mm)

9"

(229 mm)

30"

(762 mm)

15"

(381 mm)

IMPORTANT!

The side walls of the niche must be

perfectly straight. The furniture return

area has to be at least 4" (100 mm)

deep.

A Area for installation of the water connection

It is recommended the water-box be placed adjacent to the installation niche, so that it can be accessed for

service without uninstalling the appliance. If this is not possible, place the recessed water box within the shaded

area.

B Area for installation of the power connection

C Opening depth of niche, depending on kitchen design

C = 24" (610 mm) minimum

en-us

9

Required accessories and tools

Supplied accessories

ʋ Installation instructions

ʋ Operating instructions

ʋ Installation kit

Optional accessories

Freedom Heater Kit for Side-by-Side Installation

HEATKITB80

If the gap between the appliances is less

than 6" (160 mm).

Other required accessories

Ice maker installation kit

1

/

4

" OD copper line

For connecting appliances which require water, e.g. for

an ice maker.

Maximum outer diameter of the water pipe (without

fittings):

3

/

8

" (9.5 mm).

Miscellaneous

ʋ Stepladder

ʋ Dolly, hand truck

ʋ Hammer drill for drilling holes in wall or floor

ʋ Bits according suitable for material and in different

sizes

ʋ Wooden beam (cross section min. 3" x 4") as an

alternative tip protection, length according to the

width of the installation niche

ʋ Wooden screws in different sizes

ʋ Thin plywood sheet, particle board or cardboard

to protect the floor from damage

ʋ Suitable material for covering and protecting

furniture (e.g. protective sheets)

ʋ Adhesive tape

Note:

Before using, check whether the removed adhesive

tape leaves adhesive residue on the work surfaces!

Otherwise do not use on high-quality work surfaces.

Tools

Cordless screwdriver

Torx bit T20 / T30 +

magnetic holder

Torx screwdriver T20

5

/

16

" (8 mm) hex nut driver

Wood drills in different sizes

Open end wrench

1

/

2

"

(SW 13 mm)

Multigrip pliers

Adjustable wrench

Cutter with adjustable blade

Metal tape measure, folding

rule

Square

Level, length 2' (60 cm) and

4' (1.2 m)

Level, min. 4' (1.2 m) long

en-us

10

Installation instructions

The following installation instructions describe the

installation steps for various appliance types:

Refrigerator units

Freezer units

Freezer units with ice maker

Therefore the diagrams may be a general

representation of your appliance.

Particular reference is made to special installation steps

for individual appliance types.

1. Checking the installation niche

CAUTION:

Use the following check list for a safe and

trouble free installation.

1.

Check the floor.

See chapter “Installation”, section “Floor”.

2.

Check the dimensions of the installation niche,

see chapter “Dimensions of the installation niche”.

3.

Check that the installation niche is square.

4.

Check location of the socket.

See chapter “Connecting the power” and

chapter “Dimensions of the installation niche”.

5.

Check location of the water connection

(only for appliances with ice maker).

See chapter “Connecting the water” and

chapter “Dimensions of the installation niche”.

6.

Check attachment of the adjacent cabinet/fixtures.

All cabinet parts in the vicinity of the appliance

must be connected securely to the wall.

7.

Check that adjacent cabinet/fixtures have

adequate clearance (door opening angle).

2. Removing the packaging

WARNING:

Be careful, otherwise people who are helping

may be injured or the appliance may be

damaged!

The appliance may tip over while it is being

unpacked or if the doors are opened.

The appliance is very heavy.

Data relating to the weight when empty is

found in the following table:

Note:

Check appliance for damage in transit.

Do not install the appliance if it is visibly damaged.

If in doubt, contact your dealer.

To avoid floor damage:

1.

Remove the packaging carton and be careful not

to damage the surface of appliance.

2.

Place packaging cardboard or plywood under the

appliance.

3.

Remove accessories from the outside of the

appliance.

Save adhesive tape which was used to attach the

supplied accessories to the appliance.

It can be used subsequently for attaching an edge

protection to the installation niche walls (see

chapter “A / 3. Attaching an edge protection”).

4.

Remove transportation protection devices (a) and

lift appliance off the pallet – appliance is very

heavy!

5.

Carefully open the appliance

– risk of tipping over –

and remove accessories and installation materials

from inside the appliance. Close the door again.

Note:

Do not remove transportation safety devices which

protect the shelves and storage compartments inside

the appliance until the installation is complete,

otherwise the parts may be damaged.

Refrigerator 30" approx. 350 Ibs/158 kg

Freezer 18" approx. 255 Ibs/115 kg

a

en-us

11

3. Transport of the appliance

 WARNING:

Be careful, otherwise people who are helping

may be injured or the appliance may be

damaged!

The appliance is very heavy.

The appliance is 83

1

/

8

" (2126 mm) tall. If the appliance

cannot be transported in an upright position, the

appliance can be transported horizontally.

Note:

Do not raise up the appliance via the side panels. Risk

of damage to the appliance!

When raising up the appliance, observe the required

minimum height at the installation location according to

the following table:



Note:

Always use the appliance dolly from the rear side of the

appliance. Never push it in from the front under the

appliance. Risk of damage to the appliance!

1.

Transport the appliance to a suitable installation

location with suitable means of transportation

(trolley, lifting truck or hand).

2.

Secure the appliance during transportation to

prevent it from tipping.

4. Installation preparation

Unpack installation materials and accessories.

To simplify installation, the packages are identified with

labels A, B and C corresponding with the manual

chapters.

5. Special installation

Special installation steps are described after chapter C.

The following symbol indicates that additional steps

need to be taken before proceeding to the next

chapter.

ʋ The appliance may tip over while it

is being unpacked or if the doors

are opened.

ʋ Sealing mat, see “Removing/

changing over the sealing mat”

ʋ Side-by-Side installation,

see “Side-by-Side installation”.

ʋ Connecting the water, see

“Preparing to connect the water”

and “Connecting the water to the

appliance”.

ʋ Door limitation pin, see “Adjusting

the door opening angle”.

Raise up via appliance

rear

Do not raise up from

appliance side

Minimum height

86"/2185 mm

Do not raise up the

appliance via the side

panels!

en-us

12

1. Attaching the anti-tip-brackets

 WARNING:

Risk of injury and damage!

Assure that there are no electrical wires or

plumbing in the area which the screws could

penetrate.

 WARNING:

Risk of injury! Always wear safety glasses and

other necessary protective devices or apparel

when installing or working with dowels.

Important note:

If a Side-by-Side set up of two appliances is envisaged,

the anti-tip brackets are needed as installation aid.

Connect the appliances before the anti-tip brackets are

fixed to the wall, see “Side-by-Side installation”.

Note:

ʋ 2 anti-tip-brackets are required for each appliance.

ʋ The supplied set contains fastening screws for

various applications. Select the fastening screws

according to the local conditions.

ʋ If the anti-tip brackets, and therefore the appliance,

cannot be securely attached with the supplied

fastening screws, another suitable method must be

used to attach the appliance securely.

The anti-tip-brackets (a) must overlap a minimum of

21/8” (54 mm) over the appliance to secure the

appliance.

If this minimum length cannot be observed for

structural conditions it is possible to do this by

fastening a spacer (b) behind the anti-tip angle, e.g. a

sufficiently dimensioned wood board.

The length of the plank should correspond to the width

of the installation niche!

1.

Specify the attachment points of the anti-tip-

brackets according to the chapter on “Dimensions

of the installation niche”.

2.

Attach the anti-tip-brackets completely.

Be sure screws hold tight.

Important notes for fastening with dowels and

screws:

Not recommended for use in light-weight masonry

material such as cinder block.

Not recommended for use in new concrete which has

not had time to cure.

en-us

13

2. Attaching an alternative anti-tip

device

Important note:

If the anti-tip brackets cannot be attached securely, an

alternative anti-tip-device can be attached. However,

ensure that there is no play between the appliance and

the anti-tip-device. If possible, always screw the wooden

beam to existing studs on the rear panel of the

installation niche.

1.

Specify the attachment points of the anti-tip-

brackets according to the chapter on “Dimensions

of the installation niche”.

Note:

ʋ If the installation niche is deeper than the

appliance, select a beam which has a larger

cross section or attach 2 beams.

ʋ The beam must cover the appliance by

at least 2" (50.8 mm).

2.

Mark the installation height (lower edge of the

beam) on the rear panel of the installation niche.

3.

Select screws according to the thickness of the

wooden beam: length = min. 2.5 x beam

thickness, diameter #12 or #14.

Note:

Choose the number of screws according to the

installation niche width, thereby ensuring that the

beam can be attached securely.

4.

Depending to the subsurface:

Locate wall studs in the rear of the installation

niche and accordingly transfer their location to the

wooden beam

or fasten suitable dowel into the rear wall.

5.

Predrill the wooden beam.

6.

Attach the wooden beam to the rear panel of the

installation niche.

3. Attaching an edge protection

To protect the edges of the installation niche, it is

recommended to attach edge protection made of a

suitable material.

The following are special installation

steps. Instructions are provided after

chapter C.

ʋ Change over door hinge, see

“Changing over the door hinges”.

ʋ Sealing mat, see “Removing/

changing over the sealing mat”

ʋ Side-by-Side installation,

see “Side-by- Side installation”.

ʋ Connecting the water, see

“Preparing to connect the water”.

en-us

14

1. Pushing the appliance into the

installation niche

 CAUTION:

Caution when pushing the appliance into the

installation niche. Do not damage the water line

or power cord.

Note:

When the floor or the appliance is not leveled in

comparison to the installation niche adjust height

adjustable wheels before you move the appliance into

the installation niche.

1.

Remove the base panel.

2.

Raise the height-adjustable wheels at the back by

approx.

3

/

8

" (10 mm).

3.

Put the electric plug into the socket.

4.

Push the water line into the guard tube (a) at the

rear of the appliance.

 WARNING:

Be careful, otherwise people who are helping

may be injured or the appliance may be

damaged.

The appliance may tip over while the water

line is pushing into the guard tube (a).

5.

To prevent the power cord from becoming caught,

tie a piece of string to the middle of the power

cord and feed forwards over the top of the

appliance. When pushing in the appliance, pull the

cable upwards. Take care not to pinch the power

cord

or

using adhesive tape, tape the power cord to the

floor centrally behind the appliance approx. 15"

(380 mm) away from the rear panel of the

installation niche.

6.

Carefully push the appliance into the installation

niche.

7.

Remove edge protection (if attached).

en-us

15

2. Aligning the appliance in the

installation niche

Note:

To ensure that the appliance functions correctly, it must

be set perfectly levelled.

Depth alignment

The positioning aid on the door have been designed for

the following total thickness of door panels:

ʋ

3

/

4

" (19 mm)

ʋ 1

1

/

2

" (38 mm)

Always take account of the possible differing thickness

of the panel fronts which are to be fitted subsequently.

1.

Align the appliance with the cabinet fronts using

the positioning aid.

Place level over the positioning aid on the door.

Height alignment

Note:

ʋ Do not twist or jam the appliance inside the

installation niche! When adjusting the

heightadjustable feet, proceed gradually: Always

alternate between left and right, etc.

ʋ For easier adjustment of the rear feet take the

weight off by slightly tilting the appliance forward.

ʋ When using a wooden beam as an alternative

antitip mechanism, turn the appliance as far as it

will go against the wooden beam. Do not bend

against the wooden beam.

The height-adjustable feet at the front and rear can all

be adjusted from the front.

The mark (a) attached at the appliance base is used as

a standard gage for height adjustment. When adjusting

the height, align this mark at a height of 1

1

/

4

" (32 mm)

above the floor.

It is very important to comply with this dimension for the

subsequent alignment of the furniture fronts.

The height adjustment gauge (b) is used

to set this height correctly. The upper

edge of the gauge must be in alignment

with the mark on the appliance.

2.

Unscrew the feet at the front of the appliance until

the mark (a) on the appliance is in alignment with

the upper edge of the height adjustment

gauge (b).

3.

Align the appliance vertically using the feet at the

back. Use a level!

Front:

with open-ended wrench

1

/

2

"

(Width across flats 13 mm)

Rear:

with

5

/

16

" (8 mm) hex nut driver via

flexible shaft.

en-us

16

3. Attaching the appliance to the

installation niche

It is essential to attach the appliance to the top of the

installation niche.

1.

Screw the attachment plate lugs (top) to the

overhead furniture.

2.

If there is a fairly large gap above the appliance, fit

a wooden beam above the appliance, ensuring

that the wooden beam fits the gap exactly.

3.

If there is enough room on the top of the

appliance, fix the attachment plate side lugs (top)

to the side of the niche.

4.

Screw on the bars of the fastening sheets (lateral)

with the cabinet parts located next to them.

Note:

In the case of a Side-by-Side installation this

installation step is not possible. These parts have

been removed.

5.

Shorten the fitting strip (a) to fill the gap.

Note:

The appliance will be damaged if the fitting

strip (a) is too long.

6.

Press the fitting strip (a) into the cover strip (b).

7.

Attach the cover strip (b) to the attachment plate

(top).

Note:

In the case of a side-by-side installation connect both

cover rails to the bolt included in the installation

accessories for side-by-side installation.

The following are special installation

steps. Instructions are provided after

chapter C.

ʋ Connecting the water, see

“Connecting the water to the

appliance”.

en-us

17

1. Attaching the toe kick panel

Note:

Risk of damage to the appliance. Do not cover

ventilation slots in the base panel.

Nominal dimensions to be observed:

Stainless steel panel (accessory)

1.

Attach the base panel to the appliance (do not

screw on).

2.

Remove the protective film from the adhesive

pads.

3.

Fit the toe kick panel to the base panel and press

firmly into place.

Wooden panel

1.

If required, shorten wooden panel to the required

length.

2.

Screw wooden panel to the base panel from

behind. There are already screw holes in the base

panel.

2. Aligning the base panel

1.

Put on the base panel (do not screw on) and

measure the difference in depth A between the

base panel and toe kick panel of the adjacent

cabinet.

2.

Remove the base panel.

3.

Adjust the brackets (a) to the dimensions A and

tighten.

4.

Attach the base panel.

en-us

18

3. Switching the appliance ON

To guarantee the accuracy of the following working

steps and thus the appearance of the overall kitchen

front later on, the appliance should now be operated.

1.

Open the appliance door.

2.

Press the POWER button.

3.

Press the POWER button again to shut off.

Only for appliances with a water connection:

In order to avoid the risk of damage caused by leaking

water from damage possibly caused to the water pipe

feeding the appliance, keep the shut-off valve closed.

4. Preparing the door panels

Important note:

When performing any work on the door panels, always

observe the following:

ʋ Always screw into the best load-bearing material

of the door panel.

ʋ Never screw into fillers, decorative strips or

similar.

ʋ Select a screw length which is always shorter than

the thickness of the door panel.

ʋ To prevent damage, protect surfaces of the door

panels during installation.

The total weight of the door panel must not exceed the

following values:

5. Loading the appliance door

When attaching the door panels, it is recommended to

load the door storage compartments in the appliance

with weights in order to ensure that the gap width is as

precise as possible.

Recommendations:

6. Removing the installation support

part

Unscrew the positioning aid from the appliance door.

Note:

Store the positioning aids, there will be used in an

installation step later.

7. Attaching the adjusting rail to the

door panel

1.

Measure the distance A between the adjusting rail

and the overhead cabinet/fixtures.

2.

Loosen the 2 nuts (a) and remove the adjusting

rail (b).

3.

Mark this amount A on the rear of the door panel.

4.

Determine and mark the centerline of the door

panel.

5.

Put on the adjusting rail and align along the

marks. Mark the drill holes.

6.

Drill the holes.

18" Appliance 44 Ibs/20 kg

30" Appliance 64 Ibs/29 kg

18" Appliance 22 Ibs/10 kg

30" Appliance 44 Ibs/20 kg

en-us

19

7.

Screw on the adjusting rail tightly.

Note:

ʋ Attach the adjusting rail to the door panel with at

least 10 screws. One screw should be inserted

under each double threaded bolt.

ʋ The adjusting rail features a variety of holes for the

many different design options of door panels.

ʋ Always screw into the best load-bearing material

of the door panel.

8. Attaching the fixation strips to the

door panel

Note:

The fixation strips are pre-assembled for stainless steel

doors. In this case continue with the next installation

step (“C / 9. Attaching the door panel”).

1.

Hang the door panel on the double threaded

bolt (a).

2.

Align the door panel with the double threaded

bolts (Torx screwdriver).

Re-examine the dimensions of the gap

continuously.

Use the height adjustment gauge (b).

3.

Transfer the middle drill holes along the outer

edge of the appliance door to the door panel and

mark.

4.

Remove the door panel.

5.

Using the positioning aid, mark the vertical sides

of the door panel parallel.

6.

Using a square, extend the drill hole marks which

you have just made to the vertical marks.

7.

Apply the fixation strip and mark out the holes.

8.

Pre-drill the holes.

en-us

20

9.

Screw on the fixation strips.

9. Attaching the door panel

Note:

Now attach the furniture handles which are screwed

from behind!

1.

Remove the fixing brackets (a) from the appliance

door. To do this, loosen the bracket screws (b)

only.

2.

Insert removed fixing brackets (a) into the

adjusting rails (b) on the door panel.

3.

Open the appliance door.

4.

Hang the door panel with adjusting rail over the

double threaded bolts.

5.

Lower door panel and push the fixing brackets

down over the fastening screws.

6.

Adjust the door panel using the double threaded

bolts (Torx screwdriver). Re-examine the

dimensions of the gap continuously.

7.

Close the door and check that the depth of the

door panel is aligned with the adjacent fronts.

If required, correct.

8.

Tighten the bracket screws to fix the depth

alignment.

La page charge ...

Bosch Benchmark B18IF900SP Guide d'installation

Bosch Benchmark B18IF900SP Guide d'installation

dans d''autres langues

Documents connexes

Autres documents