GE ZDT165SSLSS Guide d'installation

Marque: GE

Modèle: ZDT165SSLSS

Catégorie: Lave-vaisselle

Taper: Guide d'installation

Ce manuel convient également à

ZDT165SILII

Monogram.com

Installation

Instructions

Built-In Dishwashers

ENGLISH/FRANÇAIS/ESPAÑOL

READ CAREFULLY

KEEP THESE INSTRUCTIONS

FOR YOUR SAFETY

Read and observe all WARNINGS and CAUTIONS

shown throughout these instructions.

While performing installations described in this

booklet, gloves and safety glasses or goggles

should be worn.

IMPORTANT – Observe all governing codes and

ordinances.

• Note to Installer – Be sure to leave these instructions

for the consumer’s and local inspector’s use.

• Note to Consumer – Keep these instructions with

your Owner’s Manual for future reference.

• Skill Level – Installation of this dishwasher requires

basic mechanical, electrical and plumbing skills.

Proper installation is the responsibility of the

installer. Product failure due to improper installation

is not covered under the Monogram Warranty. See

Warranty information.

• Completion Time – 1 to 3 Hours. New installations

require more time than replacement installations.

IMPORTANT – The dishwasher MUST be installed to

allow for future removal from the enclosure if service is

required.

Care should be exercised when the appliance is installed

or removed, to reduce the likelihood of damage to the

power supply cord.

If you received a damaged dishwasher, you should

immediately contact your dealer or builder.

Optional Accessories – See the Owner’s Manual for

available custom panel kits.

Your dishwasher is a water heating appliance.

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• Remove all power leading to the appliance from the

circuit breaker or fuse box before beginning installation.

Failure to do so can result in a risk of electrical shock.

•

To reduce the risk of electric shock, fire, or injury to persons,

the installer must ensure that the dishwasher is completely

enclosed at the time of installation.

• The improper connection of the equipment grounding

conductor can result in a risk of electric shock. Check

with a qualified electrician or service representative

if you are in doubt that the appliance is properly

grounded. If house wiring is not 2-wire with ground, a

ground must be by the installer. When house wiring

is aluminum, be sure to use UL-Listed anti-oxidant

compound and aluminum-to-copper connectors.

•

To reduce the risk of electric shock, fire, or injury to

persons, the installer should check to ensure that wires are

not pinched or damaged, the house wiring is attached to the

junction box bracket through a strain relief, and all electrical

connections made at the time of install (wire nuts) are

contained inside of

the junction box cover.

• Do not use an extension cord or adapter plug with this

appliance.

WARNING

• Be sure to leave complete literature package, these Installation

Instructions and product samples and/or coupons with the

consumer.

For Monogram parts and accessories, call

800.626.2002.

For Monogram parts and accessories in Canada,

call 800.561.3344.

For Monogram local service in your area,

800.444.1845.

Custom Door Panel Option

Custom front panel models include a kit that contains a

template/installation instructions and hardware. Refer to

the kit instructions when installing the custom panel.

If a custom panel mounting hardware kit and template/

installation instructions are needed, prior to delivery of

the dishwasher, order: WD35X24247.

Safety Information

Installation Preparation

PARTS SUPPLIED IN

INSTALLATION PACKAGE:

• Drain hose extension

• Hose Clamp

• 2 mounting brackets for wood countertop or side

cabinets

• Toekick Insulation

• 6 Phillips-Head screws to secure dishwasher to

underside of countertop or to side cabinets

• Literature, samples and/or coupons

TOOLS YOU WILL NEED:

• Phillips-head screwdriver

• 1/4” and 5/16” nutdriver

• T25 torque driver

• 6” adjustable wrench

• Gloves

• Safety glasses

• Flashlight

• Bucket to catch water

when flushing the line

• Level

• Measuring tape

• Carpenter’s square

For New Installations Only:

• Tubing cutter

• Drill and appropriate bits

• Hole saw set

MATERIALS YOU WILL NEED:

• UL-listed wire nuts (3)

• Thread Seal Tape

• 90° elbow (3/4” hose internal thread on one end,

opposite end sized to fit water supply)

Materials For New Installations Only:

• Air gap for drain hose, if required

• Waste tee for house plumbing, if applicable

• Electrical cable or Power Cord Kit WX09X70910 (5’ 4”

long) or WX09X70911 (7’ 9” long) depending on your

installation.

• Screw-type hose clamp(s)

• Strain relief for electrical connection

• Hand shut-off valve (recommended)

• Hot water line–3/8” minimum, copper tubing

(including ferrule, compression nut) or Monogram

Part # WX28X326, flexible braided hose.

Installation Preparation

Hole Saw Set

Measuring Tape

Tubing Cutter

Drill and Bits

Phillips-Head

Screwdriver

1/4” and 5/16”

Nutdriver

6” Adjustable

Wrench

Gloves

Carpenter’s

Square

Level

Drain Hose

Extension

Literature

Hot Water Line,

Ferrule and

Compression Nut

Strain Relief

Hose Clamp(s)

Waste Tee

Electrical Cable

(or Power Cord,

if applicable)

Wire Nuts (3)

Hand

Shut-Off

Valve

Air Gap

Thread Seal

Tape

Safety Glasses

Flashlight

Bucket

T25 Torque

Driver

Hose Clamp

Toekick Insulation

Phillips-Head

Screws

90° Elbow

Mounting Brackets

PREPARE DISHWASHER ENCLOSURE

• The dishwasher must be installed so that drain hose is

no more than 12’ in length for proper drainage.

• The dishwasher must be fully enclosed on the top, sides

and back, and must not support any part of the enclosure.

CLEARANCES:

• When installed into a corner,

allow 2” min. clearance

between dishwasher and

adjacent cabinet, wall or other

appliances. Allow 23-1/8” min.

clearance from the front of the

dishwasher for door opening.

DRAIN REQUIREMENTS

• Follow local codes and ordinances.

• Do not exceed 12’ distance to drain.

• Drain connection height is not to exceed 72” above

bottom of dishwasher.

NOTE : Air gap must be used if waste tee or disposer

connection is less than 18” above floor to prevent

siphoning.

DETERMINE DRAIN METHOD

The type of drain installation depends on the following

questions.

• Do local codes or ordinances require an air gap?

• Is waste tee less than 18” above floor?

If the answer to either question is YES, Method 1

MUST be used.

•

If the answers are NO, either method may be used.

CABINET PREPARATION

• Drill a 1-1/2” diameter hole in the cabinet wall within

the shaded areas shown in PREPARE DISHWASHER

ENCLOSURE for the drain hose connection. The hole

should be smooth with no sharp edges.

IMPORTANT – When connecting

drain line to disposer, check to be sure

that drain plug has been removed.

DISHWASHER WILL NOT DRAIN IF

PLUG IS LEFT IN PLACE.

Method 1 – Air Gap with Waste Tee or Disposer

An air gap must be used when required by local codes

and ordinances. The air gap must be installed according to

manufacturer’s instructions.

Tip: Avoid unnecessary service call charges.

Always be sure disposer drain plug has been removed

before attaching dishwasher drain hose to the disposer.

Remove

Drain

Plug

Installation Preparation

To reduce the risk of electric shock, fire, or injury

to persons, the installer must ensure that the

dishwasher is completely enclosed at the time of

installation.

WARNING

18"

Min.

32"

Min.

Drain Hose Hanger

18"

Min.

32"

Min.

Drain Hose Hanger

Method 2 – “High Drain Loop” with Waste Tee or Disposer

23-1/8"

Countertop

Dishwasher

Clearance for Door

Opening 2” Minimum

5”

4”

5”

3”

6”

24”

32-1/2” min. to

34-3/4” max.

Underside of

countertop to

floor

Floor MUST be even

with room floor

Plumbing and electric service

MUST enter shaded area

Cabinets

square

and

plumb

This wall area

MUST be

free of

pipes and wires

18”

Installation Preparation

Cabinet Preparation & Wire Routing

•

The wiring may enter the opening from either side, rear

or the floor within the shaded area illustrated above

in figure and as defined in PREPARE DISHWASHER

ENCLOSURE section.

• Cut a 1-1/2" maximum diameter hole to admit the

electrical cable. Edges of hole should be smooth and

rounded. Permanent wiring connections may pass

through the same hole as the drain hose and hot water

line, if convenient. If cabinet wall is metal, the hole

edge must be covered with a bushing.

NOTE:

Power cords with plug must pass through a

separate hole in the cabinet.

Electrical Connection to Dishwasher

Electrical connection is on the right front of dishwasher.

• For permanent connections the cable must be routed

as shown in figure. Cable must extend a minimum of

24" from the rear wall.

• For power cord connections, install a 3-prong grounding

type receptacle in the sink cabinet rear wall, 6" min. or

18" maximum from the opening, 6" to 18" above the floor.

• Use only WX09X70910 (5’ 4” long) or WX09X70911

(7’ 9” long) Dishwasher Power Cord Kit. Do not use an

extension cord or adapter plug with this appliance.

PREPARE ELECTRICAL WIRING

Electrical Requirements

• This appliance must be supplied with 120V, 60 Hz.,

and connected to an individual properly grounded

branch circuit, protected by a 15- or 20-ampere circuit

breaker or time-delay fuse.

• Wiring must be 2 wire with ground and rated for 167°F

(75°C).

• If the electrical supply does not meet the above

requirements, call a licensed electrician before

proceeding.

Grounding Instructions–Permanent Connection

This appliance must be connected to a grounded metal,

permanent wiring system, or an equipment-grounding

conductor must be run with the circuit conductors and

be connected to the equipment-grounding terminal or

lead on the appliance.

Grounding Instructions–Power Cord Models

This appliance must be grounded. In the event of a

malfunction or breakdown, grounding will reduce the risk

of electric shock by providing a path of least resistance

for electric current. This appliance is equipped with a

cord having an equipment-grounding conductor and

a grounding plug. The plug must be plugged into an

appropriate outlet that is installed and grounded in

accordance with all local codes and ordinances.

The improper connection of the equipment grounding

conductor can result in a risk of electric shock. Check with

qualified electrician or service representative if you are in

doubt that the appliance is properly grounded. Do not modify

the plug provided with the appliance; if it will not fit the outlet,

have a proper outlet installed by a qualified technician.

WARNING

Remove all power leading to the appliance from the

circuit breaker or fuse box before beginning installation.

Failure to do so can result in a risk of electrical shock.

WARNING

1-1/2” Dia.

Hole (Max.)

3”

from

Cabinet

24”

from Wall

Ground

Black

White

Metal Cabinet

Wall

Cord Protector

(Obtain locally

as needed)

Hole Diameter

1-1/2” Maximum

WATER LINE CONNECTION

• If using a flexible braided supply hose, label the

hose with the installation date to use as reference.

Flexible braided hoses, elbows and gaskets should

be replaced in 5 years.

• Turn off the water supply.

• Install a hand shut-off valve in an accessible location,

such as under the sink. (Optional, but strongly

recommended and may be required by local codes.)

• Water connection is on the left side of the dishwasher.

Install the hot water inlet line, using no less than 3/8”

copper tubing or a flexible braided hose. Route the

line as shown in PREPARE HOT WATER LINE and

extend forward at least 19” from rear wall.

• Adjust water heater for 120°F to 140°F temperature.

• Flush water line to clean out debris.

• The hot water supply line pressure must be 20-120 PSI.

Installation Preparation

PREPARE HOT WATER LINE

NOTE: Monogram recommends copper tubing for the

water line, but if you choose to use flexible hose, use

Monogram WX28X326, flexible braided hose.

• The water supply line (3/8” copper tubing or flexible

braided hose) may enter from either side, rear or

floor within the shaded area shown in the figure.

• The water supply line may pass through the same

hole as the electrical cable and drain hose. Or, cut an

additional 1-1/2" diameter hole to accommodate the

water line. If power cord with plug is used, water line

must not pass through power cord hole.

Cabinet Face

Shut-off

Valve

3" From Floor

15" From Wall

From

Cabinet

Hot

1-1/2”

Dia.

Hole

PREPARATION

Locate the items in the installation packages:

• Screws

• Drain hose extension

• Mounting brackets

• Literature, product samples and/or coupons

Turn page to begin dishwasher installation.

REMOVE TOEKICK

• Remove the 4 toekick screws

and the 2-piece toekick. Set

aside for use in Step 19.

Dishwasher Installation

STEP 2

ADJUST LEVELING LEGS

• Move the dishwasher close to the installation location

and lay it on its back. NOTE: Do not place the

dishwasher on its side.

• Measure installation height and dishwasher height.

Extend leveling legs out from the dishwasher base,

1/2” less than installation height.

CHECK DOOR BALANCE

NOTE: If installing a custom door panel (available on

some models), follow the instructions found in the

custom door panel kit WD35X24247.

• T

o check the

door balance,

hold the top of

the dishwasher

firmly.

• Check the door

balance by

opening and

closing the door.

• If the door drops

when released,

increase the

spring tension.

If the door rises

when released, decrease the spring tension.

STEP 3

STEP 1

STEP 4

INSTALL POWER CORD

Skip this step if the dishwasher will be permanently

connected to the house electrical system or has a

factory-installed power cord.

• The power cord and connections must comply with

the National Electrical Code, Section 422 and/or local

codes and ordinances. Maximum power cord length is

6 feet. Power Cord Kit WX09X70910 or WX09X70911,

available for purchase from an authorized Monogram

appliances dealer, meets these requirements.

• Remove junction box cover.

• Install strain relief in the junction box bracket.

• Insert the power cord through the strain relief and tighten.

• Make sure black, white and green dishwasher wires are

threaded through the hole in the junction box bracket.

• Connect power cord white (or ribbed) to dishwasher

white, black (or smooth) to dishwasher black and

ground to dishwasher green wire. Use UL-listed wire

nuts of appropriate size.

• Replace junction box cover using the screw. Be sure

wires are not pinched under the cover.

Decrease

Increase

Opening the door will cause the

dishwasher to tip forward when it

is not fully installed. When opening

the door prior to the dishwasher

being fully installed, hold the top of

the dishwasher securely with one hand and hold the

door with the other hand. Gloves should be worn.

CAUTION

Adjust to

Installation

Height

Leveling leg

shown with the

dishwasher laying

on its back

Black White

Ground/

Green

Dishwasher

Ground Wire

and Screw

Dishwasher Ground

Wire and Screw

Dishwasher

Wires

Junction Box Bracket

UL Listed Wire Nuts

Strain

Relief on

Power

Cord

Junction Box

Cover

STEP 6

POSITION WATER LINE

AND HOUSE WIRING

• Position water supply line and house wiring on the

floor of the opening to avoid interference with base

of dishwasher and components under dishwasher.

Dishwasher Installation

Water

Line

House

Wiring

INSTALL 90° ELBOW

• Ensure rubber gasket is located between valve and

elbow.

• Thread 90° elbow onto the water valve.

• Do not overtighten elbow. Water valve bracket could

bend or water valve fitting could break.

• Position the end of the elbow to face the rear of the

dishwasher.

Gasket

90°

Water

Valve

Screw the

90° elbow

onto the

water valve

until it is

secure and

points to the

rear of the

dishwasher

STEP 5

STEP 7

INSTALL DRAIN HOSE,

THROUGH CABINET

• Stand the dishwasher upright and position it in front

of cabinet opening. Insert drain hose into the hole in

cabinet side. If a power cord is used, guide the end

through a separate cabinet opening.

Tip: Prevent unnecessary service call charges for

fill, drain or noise concerns.

Position utility lines so they do not interfere with

anything under or behind the dishwasher.

CONNECT DRAIN LINE

The molded end of the drain hose will fit 5/8” through 1”

diameter inlet ports on the air gap, waste tee or disposer.

• Determine size of inlet port.

• Cut drain hose

connector on the

marked line, if

required, to fit the

inlet port.

• Use the drain hose

extension provided

and connect directly

to the drain loop

already attached to the unit. Secure the connection,

with hose clamp, to the provided user bag drain

hose.

• DRAIN CONNECTION HEIGHT IS NOT TO EXCEED

72” ABOVE BOTTOM OF DISHWASHER.

• TOTAL DRAIN HOSE LENGTH MUST NOT EXCEED

12 FEET FOR PROPER DRAIN OPERATION.

STEP 8

3/4"

5/8"

Cutting Lines

IMPORTANT: Do NOT cut

corrugated portion of hose

Hose Clamp

Power Cord

(If Used)

Water

Line

House

Wiring

Drain

Hose

Insulation

Blanket

Maximum

Drain Hose

Length 12’

Dishwasher Installation

CONNECT DRAIN LINE

(CONT.)

• Connect drain line to air gap, waste tee or disposer

using the previously determined method. Secure

hose with a screw-type clamp.

Method 1 – Air gap with waste tee or disposer

Method 2 – “High drain loop” with waste tee or

disposer

Fasten drain hose to underside of countertop with a

hanger.

IMPORTANT – Either one of the above methods

must be used or dishwasher will not operate

properly.

IMPORTANT – When

connecting drain line to

disposer, check to be sure that

drain plug has been removed.

DISHWASHER WILL NOT

DRAIN IF PLUG IS LEFT IN

PLACE.

Tip: Avoid unnecessary service call charges for a

no drain complaint.

Make sure excess drain hose has been pulled through

the cabinet opening. This will prevent excess hose

in the dishwasher cavity from becoming kinked or

crushed by the dishwasher.

Waste Tee Installation

Disposer Installation

Remove

Drain

Plug

STEP 8

18"

Min.

32"

Min.

Drain Hose Hanger

Waste Tee Installation

18"

Min.

32"

Min.

Drain Hose Hanger

Disposer Installation

INSTALL MOUNTING

BRACKETS

You will need the mounting brackets and 4 of the

Phillips-Head screws set aside in the PREPARATION

section.

You must install the mounting brackets onto the

dishwasher tub frame top OR sides prior to sliding

the dishwasher into place under the countertop.

The mounting brackets have several available

attachment positions to accommodate different

cabinet constructions.

TOP MOUNTING OPTION

Install mounting brackets on top if the underside

of countertop is wood or wood-like material that

accepts screws:

IMPORTANT - After installing brackets and before

closing dishwasher door, adjust the brackets by bending

them up as needed, so that they do not contact the top

of dishwasher door and cause damage.

• If you are installing the dishwasher under a counter

with a short overhang, the countertop brackets may

extend beyond the edge of the counter. If this is the

case, remove the excess length by repeatedly bending

the brackets at the front notch only until they break.

STEP 9

Phillips

Screws

Bend and break at cutout slots in brackets (if/as necessary)

on both sides after installing if counter has a short overhang.

Phillips

Screws

Bracket

Top Mounting

SLIDE DISHWASHER

PARTIALLY INTO CABINET

IMPORTANT – Do not push against front panel with

knees. Damage will occur.

•

Grasp the sides of the front panel and slide

dishwasher into the opening a few inches at a time.

• As you proceed, pull the drain hose through the

opening under the sink. Stop pushing when the

dishwasher extends about 6 inches forward of

adjacent cabinets.

•

Make sure drain hose is not kinked under or behind

the dishwasher.

• Make certain the house wiring, drain line and

water line do not interfere with components under

dishwasher.

STEP 10

Dishwasher Installation

Do not push

against front

door panel

with knee.

Damage to

the door panel

will occur.

POSITION DISHWASHER

UNDER COUNTERTOP

• Push the dishwasher into the cabinet.

• Push the sides with your hands. Do not use your

knee against the door since door damage will occur.

• Check that the tub insulation blanket does not get

“bunched-up” or interfere with the springs as you

slide it into the cabinet.

• Center the dishwasher in the opening.

• Front of door panel should be flush with face of

cabinet.

• Carefully open and close the door to ensure that the

door panel does not catch or rub on the cabinet frame.

• If the door catches or rubs on the frame, reposition

and/or level the unit (see Step 14) until the door

moves freely and does not contact the cabinet frame.

STEP 11

Do not push

against front

door panel

with knee.

Damage to

the door panel

will occur.

INSTALL MOUNTING

BRACKETS (CONT.)

SIDE MOUNTING OPTION

Install mounting brackets on sides if the countertop

is granite or similar material that will not accept

wood screws:

• Break off front portion of the tab with pliers at the

location shown, prior to attaching to dishwasher.

• Position the left-hand side bracket as shown. Repeat

with the right bracket.

STEP 9

Side Mounting

Phillips

Screws

Bracket

Bend and break at cutout slots in brackets

(if/as necessary) on both sides before installing.

Dishwasher Installation

CONNECT POWER SUPPLY

If a power cord with plug is already installed

proceed to Step 14.

• Remove junction box cover.

• Secure house wiring to the back of the junction box

with a strain relief.

• Locate the 3 dishwasher wires, (white, black and

green) with the stripped ends coming out of the AC

jumper. Use UL listed wire nuts of appropriate size to

connect incoming ground to green, white to white and

black to black.

• Replace the junction box cover using the screw.

Check to be sure that wires are not pinched under

the cover.

• If using a Power Cord Kit, use Monogram part

number WX09X70910 or WX09X70911 and refer to

the included instructions.

NOTE: Do not remove the Junction Box Bracket.

NOTE: All ground screws, brackets and wires must

remain intact.

If house wiring is not 2-wire with ground, a ground

must be provided by the installer. When house wiring

is aluminum, be sure to use UL-Listed anti-oxidant

compound and aluminum-to-copper connectors.

WARNING

STEP 13

POSITION DISHWASHER

UNDER COUNTERTOP

(CONT.)

The controls on these

models are designed

to be hidden by your

countertop. Align the

dishwasher as shown in

figure.

Leave a 1/2” minimum gap

between the underside of the

countertop and the top of the

dishwasher door as shown in

figure.

NOTE: If the drain hose

gets trapped behind the unit

it can prevent the controls

from being hidden by the

countertop.

Tip: The leveling legs can

be used to increase or

decrease the amount of gap

between the controls and

the countertop affecting the

visibility of the controls.

IMPORTANT– Leave a 1/2”

minimum gap between the

controls and the underside

of the countertop to prevent

condensation and damage

to the control panel from

screwheads.

NOTE: If this dishwasher is replacing an existing

dishwasher, the old countertop bracket screw holes

may not be in the correct position to accept a top-

control model. New holes may be required.

STEP 11

Countertop

Control

Panel

Countertop

Dishwasher

Door

1/2”

Min.

Front

View

Door

Fits and

Swings

Back

Behind

Cabinet

Frame

Correct

Alignment

Door Catches

on Cabinet Frame

Incorrect

Alignment

Sanitized

Clean

Start

Hold 3 Sec To Cancel

TOP VIEW

Controls Hidden by Countertop

CONNECT WATER

SUPPLY

Connect water supply line to 90° elbow.

If using a flexible braided hose connection:

• Attach nut to 90° elbow using an adjustable wrench.

If using a copper

tubing connection:

• Slide compression nut,

then ferrule over end

of water line.

• Insert water line into

90° elbow.

• Slide ferrule against

elbow and secure with compression nut.

STEP 12

Ferrule Compression

Nut

Hot Water

Supply Line

90° Elbow

Black White

Ground/

Green

Dishwasher

Ground Wire

and Screw

Dishwasher

Wires

Junction Box Bracket

UL Listed Wire Nuts

House

Wiring

with

Strain

Relief

Junction Box

Cover

Dishwasher Ground

Wire and Screw

Dishwasher Installation

LEVEL DISHWASHER

IMPORTANT – Dishwasher must be level for proper dish

rack operation, wash performance and door operation. The

dishwasher must be leveled left to right and front to back.

• Make sure 1/2” minimum gap under the countertop is

maintained.

• Remove the lower dish rack and place a level on the

door and lower rack track as shown in the figure.

• If the dishwasher is not

level, adjust the four

leveling legs individually.

Tip: Prevent unnecessary

service charges. Verify

dishwasher is leveled.

Pull the dish racks half way

out. They should stay put.

Open and close the door.

The door should fit in the

tub opening without hitting

the side of the tub. If the

racks roll on their own, or the door hits the side of tub,

re-level the dishwasher.

IMPORTANT – After leveling, verify that the dishwasher

is still in the correct position shown in Step 11.

STEP 14

SECURE DISHWASHER

TO COUNTERTOP OR

CABINET (CONT.)

IMPORTANT – Prevent door panel and control

panel damage. Dishwasher must be positioned so

the front panel and control panel do not contact the

adjacent cabinets or countertop. Mounting screws

must be driven straight and flush. Protruding screw

heads could scratch the door panel or control panel

and interfere with door operation.

Method 1

Secure dishwasher to underside of wood countertop.

• Fasten the dishwasher to the underside of the

countertop with the 2 Phillips-Head screws. Refer to

figure. Make certain screws are driven straight and

flush to prevent panel damage.

Method 2

Secure dishwasher to cabinet sides.

• Remove plug buttons from tub. Do not discard.

• Fasten the dishwasher to the adjacent cabinets with

the 2 Phillips-Head screws provided. Refer to the

figure. Make certain screws are driven straight and

flush to prevent panel damage. Do not screw into

the cabinet face frame.

• Re-install plug buttons.

• Re-check that the dishwasher is square and level at

both the top and bottom of the cabinet opening, with no

twisting or distortion of the tub or door after mounting to

the cabinets/countertop. Adjust if necessary.

• Confirm all leveling legs are in contact with the floor

to prevent the dishwasher from rocking and ensure

proper door and latch operation.

Both Methods

• When step is complete, close dishwasher door

and verify that gap between countertop and top of

dishwasher door is at least 1/2”.

STEP 15

SECURE DISHWASHER

TO COUNTERTOP OR

CABINET

In this step you will need

the 2 remaining Phillips

Head screws from the

screws set aside in the

PREPARATION section.

The dishwasher must be

secured to the countertop

or the cabinet sides.

When the underside of the

countertop is wood, use Method 1 (Countertop Mounting).

Use Method 2

(Side Mounting)

when the underside of

the countertop is made of a material, such as granite,

that will not accept wood screws.

STEP 15

Turn Legs

to Adjust

Wood Countertop

Screws into Upper Brackets

Solid Surface Countertop

Screws into Side Brackets

Plug Buttons

1/2"

Min.

ountertop

Dishwasher Door

Use Level to Check

Front-to-Back

Use Level to Check

Side-to-Side

Side Mounting

Countertop Mounting

Dishwasher Installation

DISHWASHER WET TEST

• Turn on power supply or plug power cord into outlet,

if equipped.

• Select a cycle to run and push the Start button.

• Close dishwasher door. Dishwasher should start.

• Check to be sure that water enters the dishwasher.

If water does not enter the dishwasher, check to be

sure that water and power are turned on.

• Check for leaks under the dishwasher. If a leak is found,

turn off power at the breaker, and then tighten water

connections. Restore power after leak is corrected.

• Check for leaks around the door. A leak around

the door could be caused by door rubbing or

hitting against adjacent cabinets. Reposition the

dishwasher if necessary. See Step 11.

• Open dishwasher door. Press and hold the Start

pad, until the light next to the pad turns off, to cancel

the cycle. Close dishwasher door. The unit will begin

to drain. Check drain lines. If leaks are found, turn

off power at the breaker and correct plumbing as

necessary. Restore power after corrections are

made. See Steps 7 and 8.

• Open dishwasher door and make sure all of the

water has drained. If not, check that disposer plug

has been removed and/or air gap is not plugged.

Also check drain hose to be sure it is not kinked

underneath or behind dishwasher. See Step 8.

• Press Start button once again and run dishwasher through

another cycle. Check for leaks and correct if required.

• Repeat these steps as necessary.

STEP 18

CHECK THE FOLLOWING

• Dishwasher is square and level at both the top and

bottom of the cabinet opening, with no twisting or

distortion of the tub or door.

• All 4 legs of the dishwasher are firmly in contact with

the floor.

• Drain hose is not pinched between the dishwasher

and adjacent cabinets or walls.

STEP 17

REPLACE TOEKICK

• Install toekick insulation by

placing ends of insulation

in left and right brackets.

Insulation should be

installed up under tub.

• Place the inner toekick

piece (with slots) against the

toekick bracket. The slots

should align with toekick.

Tip: Reduce sound from

under the dishwasher. Make sure toekick is

against floor.

• Place larger toekick over the inner piece and install 4

toekick screws.

• Use both toekick pieces for all installation heights.

STEP 19

PRETEST CHECKLIST

Review this list after installing your dishwasher to

avoid charges for a service call that is not covered

by your Warranty.

• Check to be sure power is OFF.

• Open door and remove all foam and paper packaging.

• Locate the Owner’s Manual.

• Read the Owner’s Manual for operating instructions.

• Check door opening and closing. If door does not

open and close freely, check for proper spring

adjustments. If door drops or closes when released,

adjust spring tension. See Step 1.

• Check to be sure that wiring is secure under the

dishwasher, not pinched or in contact with door

springs or other components. See Step 13.

• Check door alignment with tub. If door hits tub, level

dishwasher. See Step 14.

• Check door alignment with cabinet. If door hits

cabinet, reposition dishwasher. See Step 11.

• Check that door spring does not contact water line,

fill hose, wiring or other components. See Steps 10

and 11.

• Verify water supply and drain lines are not kinked

or in contact with other components. Contact with

motor or dishwasher frame could cause noise. See

Steps 10 and 11.

• Turn on the sink hot water faucet and verify water

temperature. Incoming water temperature must be

between 120°F and 140°F. A minimum of 120°F

temperature is required for best wash performance.

See “PREPARE HOT WATER LINE”.

• Add 2 quarts of water to the bottom of the dishwasher

to lubricate the pump seal.

• Turn on water supply. Check for leaks. Tighten

connections if needed.

• Remove protective film if present from the control

panel and door.

• Avoid service call charges by ensuring there is an

air gap or drain hose routed through the required

32” minimum height. See Step 8.

STEP 16

Notes

For Monogram

local service in your area, call 800.444.1845.

NOTE: Product improvement is a continuing endeavor at Monogram.

Therefore, materials, appearance and specifications are subject to

change without notice.

Printed in China

Monogram.com

Instructions

d’installation

Lave-vaisselle encastré

FRANÇAIS

VEUILLEZ LIRE ATTENTIVEMENT

CONSERVER CES DIRECTIVES

POUR VOTRE SÉCURITÉ

Veuillez lire et observer toutes les mises en garde

AVERTISSEMENT et ATTENTION données dans les

présentes directives.

Pour effectuer l’installation décrite dans les

présentes directives, il faut porter des et gants ou

des lunettes de sécurité.

IMPORTANT – Observez tous les codes et

ordonnances en vigueur.

• Note à l’installateur – Veuillez laisser les présentes

directives au consommateur pour l’inspecteur local.

• Note au consommateur – Veuillez conserver les

présentes directives avec votre Manuel d’utilisation

pour consultation ultérieure.

• Compétences requises – L’installation de ce

lave-vaisselle exige des compétences de base en

mécanique, en électricité et en plomberie.

L’installateur est responsable de la qualité

de l’installation. Toute défaillance du produit

attribuable à une installation inadéquate n’est pas

couverte par la Garantie de Monogram. Reportez-

vous à la Garantie du produit.

• Durée de l’installation – Entre 1 et 3 heures.

L’installation d’un nouveau lave-vaisselle exige plus de

temps que le remplacement d’un ancien modèle.

IMPORTANT – Le lave-vaisselle DOIT être installé de

manière à ce qu’il puisse être sorti de son emplacement

si des réparations sont nécessaires.

Il importe d'user de prudence lorsque l'appareil est

installé ou déplacé afin de prévenir l'endommagement

du cordon d'alimentation.

Si le lave-vaisselle que vous avez reçu est endommagé,

communiquez immédiatement avec votre détaillant ou

l’entrepreneur en construction.

Accessoires facultatifs – Reportez-vous au Manuel

d’utilisation pour connaître les ensembles pour panneau

décoratif personnalisé offerts.

Votre lave-vaisselle est un appareil qui chauffe l’eau.

AVANT DE COMMENCER

Veuillez lire attentivement toutes les directives qui suivent.

• Avant de commencer l’installation, coupez toute

alimentation menant de l’appareil au disjoncteur ou

au fusible. Dans le cas contraire, vous pourriez être

victime d’une décharge électrique.

• Pour réduire les risques de choc électrique,

d’incendie ou de blessures, l’installateur doit

s’assurer que le lave-vaisselle est complètement

encastré au moment de l’installation.

• Un branchement inadéquat du conducteur de

mise à la terre peut présenter des risques de choc

électrique. Si vous n’êtes pas certain que l’appareil

est correctement mis à la terre, consultez un

réparateur ou un électricien qualifié. Si le câblage

électrique de la résidence n’est pas constitué de

deux fils plus un fil de mise à la terre, l’installateur

doit installer un fil de mise à la terre. Si le câblage

électrique de la résidence est en aluminium, utilisez

un agent antioxydant et des connecteurs pour

raccords «aluminium-cuivre» homologués UL.

•

Pour réduire les risques de choc électrique, d’incendie ou

de blessures, l’installateur doit vérifier pour s’assurer que

les fils ne sont pas pliés ou en dommagés, que le câblage

domestique est fixé au support de boîte de connexion par

l’entremise d’un serre-câble et que toutes les connexions

électriques faites au moment de l’installation (capuchons

de connexion) se trouvent à l’intérieur du couvercle de la

boîte de connexion

• N’utilisez pas une rallonge électrique ou un adaptateur

de fiche avec cet appareil.

AVERTISSEMENT

• Laissez le Manuel d’utilisation, les directives d’installation,

les échantillons et(ou) les bons au consommateur.

Pièces et accessoires Monogram, appeler le:

800.626.2002.

Pièces et accessoires Monogram au Canada, appeler le:

800.561.3344.

Pour le service local Monogram dans votre région:

800.444.1845.

Option de panneau de porte de finition

Les modèles avec panneau frontal sur commande viennent

avec une trousse comprenant un gabarit / instructions

d’installation et la quincaillerie. Se reporter aux instructions de la

trousse pour installer le panneau sur commande.

Commandez votre trousse de montage de panneau et un

gabarit / instructions d’installation personnalisés WD35X24247

avant d’installer le lave-vaisselle, le cas échéant.

Information de sécurité

Préparation pour l’installation

OUTILS NÉCESSAIRES:

• Tournevis cruciforme

• Tournevis à douille de 5/16 po et 1/4 po

• Tournevis dynamométrique T25

• Clé à molette de 15 cm (6 po)

• Gants

• Lunettes de sécurité

• Lampe de poche

• Seau pour attraper l’eau

lors de la purge du tuyau

• Niveau

• Ruban à mesurer

• Équerre de menuisier

Pour une nouvelle installation:

• Coupe-tube

• Perceuse et mèches appropriées

• Jeu de scie-cloche

MATÉRIAUX NÉCESSAIRES:

• Connecteurs vissables homologués UL (3)

• Ruban pour joints filetés

• Coude de 90° (19,1 mm [3/4 po] filet pour tuyau d’arrosage

de jardin à une extrémité et l’autre extrémité conçue pour le

raccordement à la conduite d’alimentation en eau)

Pour une nouvelle installation:

• Coupure anti-refoulement pour le boyau de vidange, si nécessaire

• Raccord en T pour la plomberie de la résidence, s’il y a lieu

• Câble électrique ou Trousse de cordon d’alimentation

WX09X70910 (5,4 pi) ou WX09X70911 (7,9 pi) en fonction de

votre installation.

• Collier(s) à vis sans fin

• Bague anti-traction pour le raccordement électrique

• Robinet d’arrêt (recommandé)

• Conduite d’eau chaude – 9,5 mm (3/8 po) minimum, tuyau en

cuivre (incluant la bague et l’écrou à compression) ou la pièce

WX28X326 de Monogram, boyau métallique flexible.

PIÈCES FOURNIES DANS

L’EMBALLAGE:

• L’extension du boyau de vidange

• Collier à vis sans fin

• 2 Supports de montage pour comptoir en bois ou

armoires latérales

• Isolant de plinthe

• 6 Vis à tête Phillips pour fixer

le lave-vaisselle au

dessous du comptoir ou armoires latérales

• Documentation, échantillons et(ou) bons

Préparation pour l’installation

Scie-cloche

Ruban à mesurer

Perceuse

et mèches

Tournevis

cruciforme

Tournevis à

douille de 5/16 po

et 1/4 po

Clé à molette de

15 cm (6 po)

Gants

Équerre de

menuisier

Niveau

Conduite d’eau

chaude, la bague

et l’écrou à

compression

Bague

anti-traction

Collier(s) à vis

sans fin

Raccord en T

Câble électrique

(ou cordon

d’alimentation,

s’il y a lieu)

Connecteurs

vissables (3)

Robinet

d’arrêt

Coupure

anti-refoulement

Ruban pour

joints filetés

Lunettes de

sécurité

Lampe de

poche

Seau

Coupe-tube

Tournevis

dynamométrique

T25

Coude de

90°

L’extension du

boyau de vidange

Documentation

Collier à vis

sans fin

Isolant de plinthe

Vis à tête

Phillips

Supports de montage

PRÉPARATION DE L’OUVERTURE

DANS LES ARMOIRES

• Le lave-vaisselle doit être installé de façon à ce que le boyau

de vidange mesure au maximum 3.66 mètres (12 pieds) pour

assurer une vidange adéquate.

• Le dessus, les côtés et l’arrière du lave-vaisselle doivent être

complètement dissimulés à l’intérieur de l’ouverture. Le lave-vaisselle

ne doit soutenir aucune partie de la structure des armoires.

DÉGAGEMENTS:

• Dans le cas d’une installation

dans un coin, veuillez prévoir

un dégagement d’au moins

5,1 cm (2 po) entre le lave-

vaisselle et les armoires, le

mur ou un électroménager

adjacent. Veuillez prévoir

un dégagement d’au moins

59 cm (23-1/8 po) à l’avant

du lave-vaisselle pour

l’ouverture de la porte.

Préparation pour l’installation

EXIGENCES RELATIVES AU

SYSTÈME DE VIDANGE

• Veuillez observer les ordonnances et les codes locaux en vigueur.

• Le boyau de vidange doit avoir une longueur maximale de 3.66

mètres (12 pieds).

• Le boyau de vidange ne doit pas être raccordé à une hauteur

dépassant 1,8 m (72 po) au-dessus du bas du lave-vaisselle.

REMARQUE: Il faut installer une coupure anti-refoulement

si le raccord au broyeur à déchets ou au raccord en T se trouve

à moins de 46 cm (18 po) au-dessus du plancher afin d’éviter un

siphonage.

CHOIX DE LA MÉTHODE DE VIDANGE

Le type d’installation de vidange dépend des conditions suivantes.

• Les ordonnances ou codes locaux en vigueur exigent-ils une

coupure anti-refoulement?

• Le raccord T se trouve-t-il à moins de 46cm (18po) du plancher?

Si vous répondez OUI à l’une ou l’autre de ces

questions, vous DEVEZ utiliser la méthode n° 1.

• Si vous répondez NON, vous pouvez employer l’une ou l’autre

des méthodes.

PRÉPARATION DES ARMOIRES

• Percez un trou de 3,8 cm (1-1/2 po) de diamètre dans la

paroi de l’armoire qui se trouve dans la partie ombrée de la

PRÉPARATION DE L’OUVERTURE DANS LES ARMOIRES

pour le boyau de vidange. Assurez-vous que l’orifice ne présente

pas d’arêtes vives.

IMPORTANT – Lorsque vous branchez le boyau de vidange

à un broyeur à déchets, assurez-vous d’enlever

le bouchon de vidange. LE LAVE-VAISSELLE

NE POURRA PAS SE VIDER SI VOUS

LAISSEZ LE BOUCHON EN PLACE.

Méthode n° 1 – Coupure anti-refoulement avec raccord en

T ou broyeur à déchets

Il faut installer une coupure anti-refoulement lorsqu’elle est

exigée par les ordonnances et les codes locaux en vigueur.

Cette coupure anti-refoulement doit être installée conformément

aux directives données par le fabricant.

Méthode n° 2 – Boucle de vidange élevée avec raccord en

T ou broyeur à déchets

Conseil: Pour éviter des frais de réparation inutiles.

Assurez-vous d’enlever le bouchon de vidange du broyeur à

déchets avant d’y brancher le boyau de vidange du lave-vaisselle.

Pour réduire les risques de choc électrique, d’incendie

ou de blessures, l’installateur doit s’assurer que le

lave-vaisselle est complètement encastré au moment

de l’installation.

AVERTISSEMENT

18"

Min.

32"

Min.

18"

Min.

32"

Min.

Crochet pour boyau de vidange

46 cm

(18 po) min.

82 cm

(32 po)

min.

Crochet pour boyau

de vidange

46 cm

(18 po) min.

82 cm

(32 po)

min.

23-1/8"

Countertop

Dishwasher

Clearance for Door

Opening 2” Minimum

Comptoir

Lave-vaisselle

5,1 cm (2 po) minimum

pour l’ouverture de la porte

59 cm

(23-1/8 po)

Remove

Drain

Plug

Enlevez le

bouchon

de vidange

5”

4”

5”

3”

6”

24”

82,6cm (32-1/2po)

min. à 88,3cm

(34-3/4po) max.

dessous du

comptoir au

plancher

Le plancher DOIT être égal

au plancher de la pièce

Le service de plomberie et d’électricité

DOIT entrer dans une zone ombragée

Armoires à

l’équerre et

d’aplomb

Le mur du fond

DOIT être exempt

de tuyaux et de

fils

45,7cm (18po)

61,0 cm

(24 po)

12,7cm

(5 po)

10,2cm

(4 po)

12,7cm

(5 po)

15,2

7,6

La page est en cours de chargement...

GE ZDT165SSLSS Guide d'installation

Marque: GE

Modèle: ZDT165SSLSS

Catégorie: Lave-vaisselle

Taper: Guide d'installation

Ce manuel convient également à

ZDT165SILII

Télécharger le PDF

rapport

dans d''autres langues

English: GE ZDT165SSLSS Installation guide
español: GE ZDT165SSLSS Guía de instalación

GE ZDT165SSLSS Guide d'installation

Ce manuel convient également à

GE ZDT165SSLSS Guide d'installation

dans d''autres langues

Documents connexes

Autres documents