Indesit AQXGD 149 S (EX) Mode d'emploi

Catégorie
Machines à laver
Taper
Mode d'emploi
GB
1
WASHING MACHINE
AQUALTIS
AQXGD 149 S
Instruction booklet
Contents
Installation, 2-3
Unpacking and levelling
Connecting the cold water and electricity supplies
Technical data
Description of the machine, 4-5
Control panel
Running a wash cycle, 6
Programmes and options, 7
Table of Programmes
Wash options
Detergents and laundry, 8
Detergent
Preparing the laundry
Washing advice
Load-balancing system
Precautions and tips, 9
General safety
Disposal
Opening the door manually
Care and maintenance, 10
Turning off the water and electricity supplies
Cleaning the machine
Cleaning the detergent dispenser
Drum maintenance
Cleaning the pump
Checking the water inlet hose
Troubleshooting, 11
Assistance, 12
English,1
GB
Français,13
F
AR
, 25
GB
2
Installation
A
Keep this instruction manual in a safe place for
future reference. If the appliance is sold, given away
or moved, please ensure the manual remains with the
machine so that the new owner may benefit from the
advice contained within it.
Please read this instruction manual carefully it
contains important information regarding the safe
installation, use and maintenance of the appliance.
You will find the guarantee and other details relating to
the installation process in the bag containing this booklet.
Unpacking and levelling
Unpacking
1. Once the washing machine has been removed
from the packaging, check that it has not been
damaged during transportation.
If it has been damaged, contact the retailer and do
not proceed any further with the installation process.
2. Remove the 4 transit
bolts used during
transportation and the
corresponding spacers
on the back of the
machine (see figure).
3. Having removed the 4 bolts use the 4 plastic
blanking plates to cover the 4 holes.
4. Keep all the pieces; if the washing machine is
transported in future, the transit bolts and spacers will
have to be replaced in order to avoid damaging the
inside of the machine.
Packaging materials should not be used as toys by children.
Levelling
1. Position the washing machine on a level and sturdy
floor, without resting it against walls or cabinets.
2. If the floor is uneven,
the feet of the appliance
may be adjusted until it
reaches a perfectly
horizontal position (the
angle of inclination must
not exceed 2 degrees).
If the appliance is levelled correctly it will be more
stable and much less likely to cause vibrations and
noise during the spin cycle.
If positioned on a fitted carpet or a rug, adjust the
feet in such a way as to allow room for air to circulate
and provide ventilation beneath the washing machine.
Connecting the cold water and
electricity supplies
Connecting the water inlet hose
Before connecting the inlet hose to the cold water supply,
allow the water to flow from the tap until it runs clear.
1. Connect the end of
the water inlet hose to
the washing machine,
screwing it onto the
appliance's cold water
inlet, situated on the top
right-hand side on the
rear of the appliance
(see figure).
2. Place the seal A
(provided in the bag) on
the end of the inlet hose
and screw it to a cold
water tap with a 3/4 gas
threaded connection (see
figure).
3. Make sure there are no kinks or bends in the inlet hose.
The water pressure at the tap must fall within the values
indicated in the Technical data table (see next page).
If the water inlet hose is not long enough, contact a
specialist store or an authorised technician.
Always use the new water inlet hoses supplied with
the machine.
GB
3
Technical data
Model
AQXGD 149 S
Dimensions
width 59.5 cm
height 85 cm
depth 64.5 cm
Capacity
from 1 to 9 kg
Electrical
connections
please refer to the technical data
plate fixed to the machine
Water connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 62 litres
Spin speed
up to 1400 rotations per minute
Energy rated
programmes
according to
regulation EN 60456
COTTON WHITES programme;
temperature 60°C;
using a load of 9 kg.
This appliance conforms to the
following EC Directives:
- 89/336/EEC dated 03/05/89
(Electromagnetic Compatibility) and
subsequent modifications
- 2002/96/EC
- 2006/95/EC (Low Voltage)
65 - 100 cm
Drainage Connection
Connect the outlet hose
to a draining duct or a
stand pipe at a height
between 65 and 100 cm
from the floor. Do not
bend it under any
circumstances.
Alternatively, place the
end of the hose over the
edge of a washbasin or
tub, fastening the hose
supplied to the tap (see
figure).
The free end of the hose
should not remain
immersed in water.
We advise against the use of hose extensions; if
absolutely necessary, the length of the extension
must not exceed 150 cm and its diameter must be
the same as the original hose.
Electrical connection
Before inserting the plug into the electrical socket,
make sure that:
the socket is earthed and complies with current
regulations;
the socket can withstand the maximum load of the
appliance, which is indicated in the Technical data
table (see opposite);
the power supply voltage falls within the values
indicated in the Technical data table (see opposite);
the socket is compatible with the plug of the
appliance. If this is not the case, either the socket
or the plug must be replaced.
The machine must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
appliance exposed to rain, storms and other weather
conditions.
Once the machine has been installed, the electricity
socket should be easily accessible.
Do not use extension cables or multiple sockets.
The cable should not be bent or compressed.
The cable should be replaced only by authorised
technicians.
Warning! The company shall not be held responsible
for any incidents that occur if these regulations are
not observed.
GB
4
Description of the machine
DOOR
Always use the handle to
open the door (see
figure).
When the door is
opened a light is
switched on, illuminating
the drum.
CONTROL
PANEL
DOOR
DOOR
HANDLE
ADJUSTABLE FEET
20
1
2
DETERGENT DISPENSER
This is inside the machine
and may be accessed by
opening the door.
For information relating to
detergents, please refer
to the chapter entitled
Detergents and laundry.
1. pre-wash
compartment: use
powder detergent.
2. main wash
compartment: use
powder or liquid
detergent. If you intend to
use liquid detergent, we
recommend that it is
poured into the
compartment immediately before the wash cycle is
started.
compartment for additives: for fabric softener or
other liquid washing additives. Do not exceed the
maximum level indicated by the grille, and dilute
concentrated fabric softeners.
TOE-KICK
GB
5
Control panel
DELAY TIMER
button
DISPLAY
TEMPERATURE
button
START/PAUSE
button with indicator light
WASH
CYCLE
PHASE
icons
SPIN SPEED
button
DOOR
LOCK
indicator light
CHILD LOCK
button and indicator
light
ECO
indicator
light
OPTION
buttons
ON-OFF/CANCEL
button with indicator light
PROGRAMME
knob
and MEMO
buttons
INFO
button
ON-OFF/CANCEL button with indicator light :
press the button briefly to switch the machine on or
off. The green indicator light shows that the machine
is switched on. To switch the washing machine off
during a wash cycle, press and hold the button for
approximately 2 seconds; pressing the button quickly
or accidentally will not switch the machine off.
If the machine is switched off during a wash cycle,
the programme will be cancelled.
PROGRAMME knob: this can be rotated in both
directions. To set a more suitable programme, please
refer to the Table of Programmes.
The knob is locked into position during the wash cycle.
MEMO buttons: press and hold one of the buttons to
store a cycle with your own set preferences in the
memory of the machine. To recall a previously-stored
cycle, press the corresponding button.
TEMPERATURE
button: press to decrease the
temperature: the value will be shown on the display.
SPIN CYCLE button: press to reduce the r.p.m.
value or to exclude the spin cycle completely: the
value will be shown on the display.
DELAYED START
button: press to set a delayed
start time for the selected programme. The delay
time will be shown on the display.
OPTION buttons: the name of the option will be shown
on the display when the corresponding button is
pressed. When the relevant indicator light illuminates,
this shows that the option has been selected.
INFO button: press the button to display information
relating to the selected wash cycle and options.
WASH CYCLE PHASE icons: these light up to
provide an indication of the progress of the wash cycle
(Wash
- Rinse - Spin - Pump out ). The
text
lights up when the cycle has finished.
START/PAUSE button with indicator light: when the
green indicator light flashes slowly, press the button to
start the wash cycle. When the cycle has started, the
indicator light is illuminated in a fixed manner. To pause
the wash cycle, press the button again; the indicator light
will turn orange and begin to flash again. If the Door
Locked
indicator light is off, the porthole door may
be opened. To restart the wash cycle from the point at
which it was interrupted, press the button again.
DOOR LOCKED
indicator light: this indicates
that the porthole door is locked. To open the door,
pause the wash cycle (see following page).
CHILD LOCK
button and indicator light: this is used
to enable or disable the Child lock function, by
pressing the button for approximately 2 seconds. When
the indicator light is illuminated, the control panel is
locked. This avoids accidental changes being made to
the wash cycles, especially where children are at home.
ECO indicator light: the
icon lights up when the
electricity saving reaches at least 10% (this can be
achieved by adjusting the wash cycle settings).
When the machine is first switched on, you will be asked to
choose a language (Select Language appears on the display):
press the INFO button repeatedly until the required language
appears on the display. After 5 seconds the language
selection will be stored in the memory of the machine. If the
wrong language is selected by mistake, press and hold the
INFO and DELAYED START buttons simultaneously; this will
return the language selection menu to the display.
GB
6
Running a wash cycle
NOTE: the first time you use the washing machine,
add detergent and run an empty 90°C cotton wash
cycle without the pre-wash phase.
1. SWITCH THE MACHINE ON. Press the
button.
All the indicator lights will illuminate for 1 second
and the text OK will appear on the display; the
indicator light corresponding to the
button will
then remain lit in a constant manner and the
START/PAUSE indicator light will flash.
2. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated by the display and
in the programme table on the following page.
3. MEASURE OUT THE DETERGENT. Pull out the
detergent dispenser drawer and pour the detergent
into the relevant compartments as described in
"Description of the machine".
For advice as to the type of detergent to use for
each cycle, press the
button.
4. CLOSE THE PORTHOLE DOOR.
5. SELECT THE PROGRAMME. Turn the
PROGRAMME KNOB left or right, until the required
programme has been selected; the name of the
programme will appear on the display. A tempera-
ture and spin speed is set for each programme;
these may be adjusted. The recommended drum
load level and the cycle duration will also appear on
the display.
6. PERSONALISE THE WASH CYCLE. Use the
relevant buttons on the control panel:
Modify the temperature and/or the spin
speed. The machine automatically selects the
temperature and the maximum spin speed for the
programme set and these values may not be
increased. By pressing the
button, the tempe-
rature can be progressively reduced or even set to
cold wash OFF. By pressing the
button, the
spin speed can be progressively reduced or even
eliminated altogether OFF. If the buttons are
pressed again the maximum values are restored.
Exception: if the COTTON WHITES programme is
selected, the temperature can be increased up to
a value of 90°C.
Setting a delayed start.
To set a delayed start for the selected programme,
press the corresponding button repeatedly until the
required delay period has been reached. When this
option has been activated, the
symbol appears
on the display. To remove the delayed start option,
press the button until the display shows the text
OFF; the
symbol will disappear.
Modifying the cycle settings.
Press the button to activate the option; the
name of the option will then appear on the
display and the corresponding indicator light will
illuminate.
Press the button again to deactivate the option;
the name of the option will then appear on the
display followed by the text OFF, and the
corresponding indicator light will switch off.
If the selected option is not compatible with the
set programme, the indicator light will flash and the
option will not be activated.
If the selected option is not compatible with
another option that has been selected previously,
the indicator light corresponding to the first option
selected will flash and only the second option will be
activated; the indicator light corresponding to the
active option will remain lit in a constant manner.
The options may affect the recommended load
value and/or the duration of the cycle.
7. START THE PROGRAMME. Press the START/
PAUSE button. The corresponding indicator light
remains lit in a fixed manner and the porthole door
locks (the DOOR LOCKED
indicator light
illuminates). During the wash cycle, the display will
show which stage is currently in progress and the
icon corresponding to each stage will illuminate. To
change a programme while a cycle is in progress,
pause the washing machine by pressing the
START/PAUSE button; then select the desired cycle
and press the START/PAUSE button again.
To open the door while a cycle is in progress press
the START/PAUSE button; if the DOOR LOCK
indicator light switches off it is possible to open the
door. Press the START/PAUSE button again to
resatrt the programme from the point at which it
was interrupted.
8. PROGRAMME END. The text END lights up to
indicate that the programme has ended. The
porthole door may be opened immediately. If the
START/PAUSE button flashes, press the button to
end the cycle. open the door, unload the laundry
and switch off the machine.
If you wish to cancel a cycle that has already
begun, press and hold the
button. The cycle will be
stopped and the machine will switch off.
BAG FOR QUILTS, CURTAINS AND DELICATE
GARMENTS
Ariston has made it easier for you to wash even the
most valuable and delicate garments in complete
confidence thanks to the special bag which protects
the laundry (this is supplied with the machine).
We recommend that the bag is used every time you
wash quilts and padded items with an outer layer
made using synthetic material.
GB
7
Icon Programme description
Max.
tempera-
ture (°C)
Max.
spin
speed
(r.p.m.)
Detergent
Maximum load
(kg))
Cycle duration
Washing
Fabric
softener
Normal
Using
Mini
load
Everyday programmes
COTTON WHITES
60°
(Max 90°)
1400
ll
94
COTTON WHITES:
Heavily soiled whites and delicate
colours.
40° 1400
ll
94
COTTON COLOURFAST
40° 1400
ll
94
SYNTHETICS DELICATE
40° 800
ll
42
FASTWASH: Refreshes lightly soiled garments quickly
(not recommended for wool, silk or clothes that
should be washed by hand).
30° 800
ll
3.5 1.5
Vigorous programmes
COTTON PREWASH:
Removes stubborn stains.
(Add detergent to the relevant compartment).
90° 1400
ll
94
SYNTHETICS NON-DELICATES
60° 800
ll
42
Special programmes
SHIRTS
40° 600
ll
21
SILK: Washes silk and garments and lingerie.
30° 0
ll
21
WOOL: Washes wool, cashmere, etc.
40° 600
ll
21
DUVETS:
Washes garments filled with goose down.
30° 1200
ll
31, 5
BED&BATH: Washes bathroom laundry and bedlinen
60° 1400
ll
94
Partial programmes
Rinse cottons - 1400 -
l
94
Rinse delicates - 800 -
l
42
Fast spin cottons - 1400 - - 94
Slow spin delicates - 800 - - 42
Pump out - 0 - - 94
Programmes and options
Table of Programmes
Wash options
Super Wash
This option guarantees a high-performance wash,
thanks to the use of a greater quantity of water
during the initial phase of the cycle and a longer
overall duration of the programme.
It is not compatible with the Fastwash, Silk, Wool,
Duvets and Partial programmes.
Easy Iron
If this option is selected, the wash and spin phases will
be adjusted accordingly so that fabric creasing is
reduced. At the end of the cycle the drum of the
washing machine will spin slowly; the Easy Iron and
START/PAUSE indicator lights will flash. To end the
cycle, press the START/PAUSE button or the Easy
Iron button.
When using the Silk programme, the machine will end
the cycle while the laundry is soaking and the Easy
Iron indicator light will flash. To drain the water so that
the laundry can be removed, press the START/PAUSE
button or the Easy Iron button.
This option is not compatible with the Wool, Fast spin
cottons, Slow spin cottons and Pump out programmes.
Extra Rinse
This programme increases the efficiency of the rinse
phase and ensures that a greater amount of
detergent is removed. It is particularly recommended
for skin types that are sensitive to detergents. We
recommend this programme is used when the
washing machine is full or when a large amount of
detergent has been used.
This option is not compatible with the Fastwash,
Fast spin cottons, Slow spin cottons and Pump out
programmes.
Mini load
This function should be used when the amount of
laundry is half, or less than half, of the maximum
recommended load (see Table of Programmes).
This option is not compatible with the Fast spin
cottons, Slow spin cottons and Pump out programmes.
The information contained in the table is purely indicative.
The wash cycle duration can be viewed on the display.
GB
8
Detergents and laundry
Detergent
The type and quantity of detergent used depends on
the type of fabric (cotton, wool, silk...), its colour, the
temperature of the wash, the level of soiling and the
hardness of the water in the area.
Measuring out the detergent carefully will avoid
accidental spills and help to protect the environment:
although they may be biodegradable, detergents
contain elements that alter the balance of nature.
We recommend:
the use of powder detergents for white cotton
garments and for pre-wash phases;
the use of liquid detergents for delicate cotton
garments and for all programmes which run at a
low temperature;
the use of liquid detergents for wool and silk.
Do not use detergents when washing garments by
hand, because they create too much foam.
The detergent must be measured out into the relevant
compartment, or into the detergent dosing ball which will be
placed directly into the drum of the machine. In this case
the Cotton cycle with pre-wash phase may not be selected.
Preparing the laundry
Unfold all items of laundry before placing them in the
machine.
Divide the laundry according to type of material (the
symbol on the garment label) and colour, making sure
that whites are separated from coloured garments.
Empty all pockets and check for loose buttons.
Do not exceed the values indicated in the Table of
Programmes, which refer to the weight of the
laundry items when they are dry.
How much does your laundry weigh?
1 sheet 400 - 500 g
1 pillowcase 150 - 200 g
1 tablecloth 400 - 500 g
1 bathrobe 900 - 1200 g
1 towel 150 - 250 g
1 pair of jeans 400 - 500 g
1 shirt 150 - 200 g
Washing advice
Shirts: use a suitable programme to wash shirts made
from different fabrics and in different colours. This will
guarantee that these garments are looked after properly.
Silk: use the relevant programme designed for all silk
garments. We recommend the use of a special
detergent for delicate garments.
Curtains: these should be folded and placed inside
the bag provided. Use the "Silk" programme.
Wool: Ariston is the only washing machine to have
obtained the prestigious Woolmark Platinum Care mark of
recognition (M.0508) from The Woolmark Company, which
certifies the machine washing of all woollen garments,
even those whose label states hand wash only
. The
Wool programme therefore offers you complete peace of
mind when washing all woollen garments, with great
performance guaranteed every time.
Duvets: to wash double or single duvets (the weight of
which should not exceed 3 kg), cushions or clothes
padded with goose down such as puffa jackets, use the
special "Duvets" programme. We recommend that
duvets are placed in the drum with their edges folded
inwards (see figure) and that no more than ¾ of the
total volume of the drum is used.
To achieve the best results, we recommend that a
liquid detergent is used in conjunction with the
detergent dispenser drawer.
Quilts: to wash quilts with a synthetic outer layer, use
the bag provided and set the programme to "Duvets".
Bathroom laundry and bedlinen: this washing
machine can be used to wash any domestic laundry
in a single cycle called BED&BATH that optimises
the use of fabric softener while saving both time and
electricity. We recommend that you use a powder
detergent.
Stubborn stains: stubborn stains should be treated
with solid soap before the garment is washed (use the
Cotton programme with pre-wash phase).
Load-balancing system
Before every spin cycle, to avoid excessive vibrations
and to distribute the load in a uniform manner, the
drum rotates continuously at a speed which is slightly
faster than the normal washing speed. If, after several
attempts, the load is still not evenly distributed, the
machine spins at a lower speed than the set
frequency.
If the load is excessively unbalanced, the washing
machine continues at distribution speed only instead
of the full spin speed.
In order to achieve better load distribution and
balance, we recommend that large and small
garments are mixed when placing the laundry in the
machine.
GB
9
Precautions and tips
20
This machine was designed and manufactured in
compliance with cuurent international safety
standards. The following advice is provided for safety
reasons and should be read carefully.
General safety
This appliance was designed for domestic use
inside the home and is not intended for commercial
or industrial use.
The washing machine must be used by adults only,
in accordance with the instructions provided in this
booklet.
Do not touch the machine when barefoot or with
wet or damp hands or feet.
When unplugging the appliance, always pull the
plug from the mains socket; do not pull on the
cable.
Do not touch the drained water as it may reach
extremely high temperatures.
Never force the porthole door: doing so may
damage the safety lock mechanism designed to
prevent the door being opened accidentally.
If the appliance breaks down, under no
circumatances must you attempt to carry out the
repairs yourself.
Keep children well away from the machine while it
is in operation.
If the machine must be moved, work in a group of
two or three people and handle it very carefully.
Never attempt to move the appliance without the
help of another person, because it is extremely
heavy.
Make sure that the drum is empty before loading
laundry into the appliance.
Disposal
When disposing of the packaging material: observe
local legislation so that the packaging may be reused.
The European Directive 2002/96/EC relating to
Waste Electrical and Electronic Equipment states
that household appliances should not be disposed
of using the normal solid urban waste cycle.
Exhausted appliances should be collected
separately in order to optimise the cost of re-using
and recycling the materials inside the machine,
while preventing potential damage to the
atmosphere and to public health. The crossed-out
dustbin is marked on all products to remind the
owner of their obligations regarding separated
waste collection.
For more information relating to the correct
disposal of household appliances, owners should
contact their local authorities or appliance dealer.
Opening the door manually
If it is not possible to open the porthole door due to a
powercut and you wish to hang out the laundry,
proceed as follows:
1. Remove the plug from
the electricity socket;
2. Make sure that the
water level inside the
machine is lower than the
door opening; if this is not
the case remove excess
water using the water
outlet hose, collecting it in
a bucket as shown in the
figure;
3. Remove the covering
panel on the front of the
washing machine using a
screwdriver (see figure);
4. Using the tab shown in
the figure, pull outwards
until the plastic brace
comes away; pull it
downwards until you hear
a click, which indicates
that the door is unlocked;
5. Open the door; if this is
still not possible, repeat
the process;
6. Replace the kick strip, making sure that the hooks
are positioned in the right slots before pushing the
panel towards the machine.
GB
10
Care and maintenance
1
2
Turning off the water and electricity
supplies
Turn off the water tap after every wash. This limits
wear and tear on the machines water supply and
prevents leaks.
Disconnect the appliance from the electricity supply
before cleaning it and before performing any
maintenance work on it.
Cleaning the machine
The exterior of the appliance and all rubber parts may
be cleaned using a cloth soaked in warm soapy
water. Do not use solvents or abrasive products.
Cleaning the detergent dispenser
drawer
To remove the drawer,
press the lever (1) and pull
it outwards (2) (see
figure).
Wash the drawer under
running water; this should
be done regularly.
Drum maintenance
Always leave the porthole door ajar to prevent
unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning
pump which does not require regular maintenance.
However, it may be that small objects (coins, buttons,
etc.) fall into the pre-chamber that protects the pump
(the pump is located in the lower part of this pre-
chamber).
Make sure that the wash cycle has finished and
remove the plug from the socket.
To access the pre-chamber:
1. Remove the kick strip
on the front of the
machine using a
screwdriver (see figure);
2. Position a container
collecting the drained
water (approximately 1.5 l)
correctly (see figure);
3. Unscrew the cover,
turning it in an
anticlockwise direction
(see figure);
4. Clean the inside thoroughly;
5. Screw the cover back on;
6. Replace the kick strip, making sure that the hooks
are positioned in the right slots before pushing the
panel towards the machine.
Checking the water inlet hose
Check the water inlet hose at least once a year. If
there are any cracks, replace it immediately: the high
water pressure used by the wash cycles could cause
a cracked hose to split open.
GB
11
Troubleshooting
Possible causes / Solutions:
The plug has not been inserted into the electrical socket, or it has not
been inserted far enough to make contact.
There is no power in the house.
The porthole door has not been shut properly.
The START/PAUSE button has not been pressed.
The water tap has not been turned on.
The water inlet hose is not connected to the tap.
The hose is kinked.
The water tap has not been turned on.
There is no water in the house.
The water pressure is insufficient.
The START/PAUSE button has not been pressed.
The end of the outlet hose has not been fitted at a height between 65
and 100 cm from the floor (see Installation).
The free end of the hose is underwater (see Installation).
If If the dwelling is on one of the upper floors of a building, there may be
problems relating to water drainage, causing the washing machine to
load and drain water continuously. Special anti-draining valves are
available in shops and help to avoid this inconvenience.
The water drainage systemis not fitted with a breather pipe.
The programme does not include a draining phase: some programmes
require manual draining (see Programmes and options).
The Easy Iron option is enabled: to complete the programme, press
the START/PAUSE button (see Programmes and options).
The outlet hose is bent (see Installation).
The drainage duct is clogged.
The drum was not unlocked properly when the appliance was installed
(see Installation).
The washing machine is not level (see Installation).
The washing machine is trapped between cabinets and a wall (see Installation).
The load is not balanced properly (see Description of the machine).
The water inlet hose is not screwed on to the tap correctly (see Installation).
The detergent dispenser drawer is blocked (for instructions on how to
clean it, see Care and maintenance).
The outlet hose has not been secured properly (see Installation).
Switch off the machine and unplug the appliance; wait for approximately
1 minute then switch it on again.
If the problem persists, contact Assistance.
The detergent is not designed for machine washing (the packaging
should state that the product is for washing by machine, for washing
by hand or machine or similar).
Too much detergent was used.
Follow the manual unlocking procedure (see Precautions and tips).
If the problem persists after the above checks have been carried out, shut
off the water tap, switch off the machine and contact Assistance.
From time to time your machine may not operate as it should. Before calling for Assistance (see Assistance),
make sure that the problem cannot be resolved easily using the following list.
Malfunction:
The washing machine
will not switch on.
The wash cycle
does not begin.
The washing machines fails to
fill with water.
The machine continuously fills
and drains water.
The machine does not drain
or spin.
The washing machine vibrates
too much during the spin cycle.
The washing machine leaks.
The icons corresponding to the
Phase in progress flash
rapidly at the same time as the
ON/OFF indicator light.
There is too much foam.
The washing machine door
remains locked.
GB
12
Assistance
Before contacting Assistance:
Check whether you can resolve the problem on your own (see Troubleshooting);
Restart the programme to check whether the problem has been overcome;
If this is not the case, contact the Authorised Technical Assistance Centre.
If the machine has been installed or used incorrectly, you may be charged for the maintenance callout service.
Never use the services of an unauthorised technician.
Have the following information ready:
The type of problem experienced;
The appliance model (Mod.);
The serial number (S/N).
This information can be found on the appliance data plate.
F
13
Français
Sommaire
Installation, 14-15
Déballage et mise à niveau
Raccordements eau et électricité
Caractéristiques techniques
Description de lappareil, 16-17
Tableau de bord
Comment faire un cycle de lavage, 18
Programmes et options, 19
Tableau des programmes
Les options de lavage
Produits lessiviels et linge, 20
Lessive
Triage du linge
Conseils de lavage
Système déquilibrage de la charge
Précautions et conseils, 21
Sécurité générale
Mise au rebut
Ouverture manuelle de la porte hublot
Entretien et soin, 22
Coupure de larrivée deau et de courant
Nettoyage de lappareil
Nettoyage du tiroir à produits lessiviels
Entretien du tambour
Nettoyage de la pompe
Contrôle du tuyau darrivée de leau
Anomalies et remèdes, 23
Assistance, 24
F
AQUALTIS
AQXGD 149 S
Mode demploi
LAVE-LINGE
14
F
Installation
A
Conserver ce mode demploi pour pouvoir le
consulter à tout moment. En cas de vente, de
cession ou de déménagement, veiller à ce quil
accompagne toujours le lave-linge.
Lire attentivement les instructions: elles fournissent
des conseils importants sur linstallation, lutilisation et
la sécurité de lappareil.
Cette notice, la garantie et les pièces servant à
linstallation sont réunies dans un sachet.
Déballage et mise à niveau
Déballage
1. Sitôt le lave-linge déballé, sassurer quil na pas
été endommagé pendant son transport.
Sil est abîmé, ne pas le raccorder et contacter
aussitôt le vendeur.
2. Enlever les quatre vis
de protection pour le
transport et la cale,
placés dans la partie
arrière (voir figure).
3. Boucher les trous à laide des bouchons plastique
fournis dans le sachet.
4. Ces pièces sont à conserver car il faut les
remonter en cas de déplacement du lave-linge pour
éviter dendommager lintérieur de lappareil pendant
le transport.
Les emballages ne sont pas des jouets pour enfants.
Mise à niveau
1. Poser le lave-linge sur un sol plat et rigide, sans
ladosser à un mur ou à un meuble.
2. Pour compenser les
irrégularités du sol, visser
ou dévisser les pieds de
réglage jusquà ce que
lappareil soit
parfaitement à
lhorizontale (il ne doit
pas être incliné de plus
de 2 degrés).
Une mise à niveau minutieuse garantit une bonne
stabilité de lappareil et évite toute vibration et bruit
surtout pendant lessorage.
Si lappareil est posé sur de la moquette ou un
tapis, agir sur les pieds de réglage de manière à ce
quil y ait suffisamment de place pour assurer une
bonne ventilation.
Raccordements eau et électricité
Raccordement du tuyau darrivée de leau
Avant de raccorder le tuyau darrivée de leau, laisser couler
leau jusquà ce quelle soit limpide.
1. Raccorder le tuyau
darrivée de leau à
lappareil en le vissant à
la prise deau prévue,
dans la partie arrière en
haut à droite (voir figure).
2. Monter le joint A,
fourni dans le sachet, sur
lextrémité du tuyau
darrivée de leau et le
visser à un robinet deau
froide à embout fileté 3/4
gaz (voir figure).
3. Attention à ce que le tuyau ne soit pas plié ou écrasé.
La pression de leau doit être comprise entre les
valeurs indiquées dans le tableau des
Caractéristiques techniques (voir page ci-contre).
Si la longueur du tuyau dalimentation ne suffit pas,
sadresser à un magasin spécialisé ou à un
technicien agréé.
Ne jamais utiliser de tuyaux darrivée usés mais
uniquement ceux fournis avec lappareil.
F
15
Caractéristiques techniques
Modèle
AQXGD 149 S
Dimensions
largeur 59,5 cm
hauteur 85 cm
profondeur 64,5 cm
Capaci
de 1 à 9 kg
Raccordements
électriques
voir la plaque signalétique appliquée
sur la machine
Raccordements
hydrauliques
pression maximale 1 MPa (10 bar)
pression minimale 0,05 MPa (0,5 bar)
capacité du tambour 62 litres
Vitesse
d'essorage
jusqu'à 1400 tours minute
Programmes de
contrôle selon la
norme EN 60456
programme COTON BLANC;
température 60°C;
effectué avec une charge de 9 kg.
Cet appareil est conforme aux
Directives Communautaires suivantes:
- 89/336/CEE du 03/05/89
(Compatibilité électromagnétique) et
modifications suivantes
- 2002/96/CE
- 2006/95/CE (Basse Tension)
65 - 100 cm
Raccordement du tuyau de vidange
Raccorder le tuyau de
vidange à un conduit
dévacuation ou à une
évacuation murale
placés à une distance du
sol comprise entre 65 et
100 cm en évitant à
tout prix de le plier.
Autrement, accrocher le
tuyau de vidange à un
évier ou à une baignoire,
dans ce cas, fixer le
support plastique fourni
avec lappareil au
robinet (voir figure).
Lextrémité libre du tuyau
de vidange ne doit pas
être plongée dans leau.
Lutilisation dun tuyau de rallonge est absolument
déconseillée mais si on ne peut faire autrement, il
faut absolument quil ait le même diamètre que le
tuyau original et sa longueur ne doit pas dépasser
150 cm.
Branchement électrique
Avant de brancher la fiche dans la prise de courant,
contrôler que:
la prise est bien reliée à la terre et est conforme
aux normes;
la prise est bien apte à supporter la puissance
maximale de lappareil indiquée dans le tableau des
Caractéristiques techniques (voir ci-contre);
la tension dalimentation est bien comprise entre
les valeurs figurant dans le tableau des
Caractéristiques techniques (voir ci-contre);
la prise est bien compatible avec la fiche de
lappareil. Autrement, remplacer la prise ou la
fiche.
Cet appareil ne doit pas être installé à lextérieur,
même à labri, car il est très dangereux de le laisser
exposé à la pluie et aux orages.
Après installation de lappareil, la prise de courant
doit être facilement accessible.
Nutiliser ni rallonges ni prises multiples.
Le câble ne doit être ni plié ni trop écrasé.
Le câble dalimentation et la fiche ne doivent être
remplacés que par des techniciens agréés.
Attention! Nous déclinons toute responsabilité en cas
de non-respect des normes énumérées ci-dessus.
16
F
TABLEAU DE
BORD
PORTE HUBLOT
POIGNEE PORTE
HUBLOT
SOCLE
PIEDS REGLABLES
Description de lappareil
PORTE HUBLOT
Pour ouvrir la porte, se
servir de la poignée
prévue (voir figure).
Louverture de la porte
déclenche léclairage du
tambour.
1
2
20
TIROIR A PRODUITS LESSIVIELS
Il est situé à lintérieur de
lappareil et il faut ouvrir la
porte pour y accéder.
Pour le dosage des
produits lessiviels, consulter
le chapitre Produits
lessiviels et linge.
1. bac à produit de
prélavage: utiliser de la
lessive en poudre.
2. bac à produit de lavage:
utiliser de la lessive en
poudre ou liquide. Dans ce
dernier cas, il est
recommandé de le verser
juste avant de démarrer le
lavage.
bac à additifs: pour assouplissant ou additifs
liquides. Il est recommandé de ne jamais dépasser le
niveau maximal indiqué par la grille et de diluer des
assouplissants concentrés.
F
17
Touche avec voyant MARCHE ARRET et
ANNULATION: appuyer brièvement sur la touche pour
allumer ou éteindre lappareil. Le témoin vert indique que
lappareil est sous tension. Pour éteindre le lave-linge en
cours de lavage, appuyer sur la touche pendant au
moins 2 secondes de suite; une pression brève ou
accidentelle nentraîne pas larrêt de lappareil.
Larrêt de lappareil pendant un lavage annule le lavage
en cours.
Bouton PROGRAMMES: il peut tourner dans les
deux sens. Pour sélectionner le programme plus
adapté, consulter le Tableau des programmes.
Pendant le lavage, le bouton reste fixe.
Touches MEMO: exercer une pression sur une des
touches pour mémoriser un cycle et les
personnalisations préférées. Pour retourner à un
cycle précédemment mémorisé appuyer sur la
touche correspondante.
Touche
TEMPERATURE: appuyer pour diminuer la
température, la valeur correspondante est affichée à l'écran.
Touche ESSORAGE: appuyer pour régler ou
supprimer l'essorage, la valeur correspondante est
affichée à l'écran.
Touche
DEPART DIFFERE: appuyer pour
sélectionner un départ différé pour le programme
choisi. Le retard est affiché à l'écran.
Touches OPTIONS: une pression sur cette touche de
l'écran affiche le nom de l'option. L'allumage du croissant
de lune correspondant signale la sélection de l'option.
Touche INFO: appuyer sur cette touche pour afficher à
l'écran les informations sur le programme et sur les options.
Icônes PHASES DE LAVAGE: elles sallument pour
indiquer le stade davancement du cycle (Lavage
- Rinçage - Essorage Vidange finale ).
Linscription
sallume quand le cycle est terminé.
Touche avec voyant START/PAUSE: quand le voyant
vert clignote lentement, appuyer sur la touche pour
démarrer un lavage. Une fois le cycle lancé, le voyant
passe à lallumage fixe. Pour activer une pause de
lavage, appuyer à nouveau sur la touche; le voyant
passe à lorange et se met à clignoter. Si le voyant
Porte verrouillée
est éteint, on peut ouvrir la porte.
Pour faire redémarrer le lavage exactement à lendroit
de larrêt, appuyer une nouvelle fois sur la touche.
Voyant
PORTE VERROUILLEE: il indique que la
porte hublot est verrouillée. Pour pouvoir ouvrir la porte,
il faut activer une pause du cycle (voir page suivante).
Touche et voyant
VERROUILLAGE DES
COMMANDES: pour activer ou désactiver le
verrouillage des commandes, garder la touche
enfoncée pendant environ 2 secondes. Le voyant
allumé indique que le tableau de bord est verrouillé.
Ceci permet déviter toute modification involontaire des
programmes, surtout sil y a des enfants à la maison.
Voyant ECO: licône
sallume quand la
modification des paramètres de lavage permet
datteindre au moins 10% déconomie délectricité.
A la première mise en service, l'afficheur demande
de SÉLECTIONNER LA LANGUE (affichage de
"Select Language"): appuyer sur la touche INFO
jusqu'à ce que la langue souhaitée soit affichée à
l'écran. Attendre 5 secondes pour mémoriser la
langue. Si une erreur a été commise au niveau de la
mémorisation de la langue, appuyer simultanément
sur les touches INFO et DEPART DIFFERE pour
retourner au menu de sélection de la langue.
Tableau de bord
Voyant
PORTE
VERROUILLEE
Touche et voyant
VERROUILLAGE
DES COMMANDES
Touche avec voyant
MARCHE/ARRET et
ANNULATION
Voyant
ECO
Touche
DEPART
DIFFERE
Touche
INFO
ECRAN
Touche avec voyant
START/PAUSE
Bouton
TEMPÉRATURE
Touches
OPTIONS
Touche
ESSORAGE
Icônes
PHASES
DE LAVAGE
Bouton
PROGRAMMES
et
Touches
MEMO
18
F
Comment faire un cycle de
lavage
REMARQUE: lors de la première mise en service du
lave-linge, lancer un cycle de lavage à vide mais avec
du produit lessiviel en sélectionnant un programme
coton 90° sans prélavage.
1. METTRE L'APPAREIL SOUS TENSION.
Appuyer sur la touche
. Tous les voyants
s'allument pendant 1 seconde et OK est affiché à
l'écran; le voyant de la touche
reste allumé et le
voyant START/PAUSE se met à clignoter.
2. CHARGER LE LINGE. Ouvrir la porte hublot.
Charger le linge en faisant attention à ne pas
dépasser la quantité indiquée dans le tableau des
programmes de la page suivante et sur l'écran.
3. DOSER LE PRODUIT LESSIVIEL. Sortir le tiroir
et placer le produit lessiviel dans les bacs
correspondants comme indiqué au paragraphe
"Description de l'appareil".
Pour tout conseil sur le type de produit lessiviel à
utiliser pour chaque cycle, appuyer sur la touche
.
4. FERMER LA PORTE HUBLOT.
5. CHOISIR LE PROGRAMME. Tourner le
BOUTON PROGRAMMES vers la droite ou vers la
gauche pour sélectionner le programme désiré. Le
nom du programme est affiché à l'écran avec
attribution d'une température et d'une vitesse
d'essorage qui peuvent être modifiées. L'écran
affiche le niveau de chargement du tambour
conseillé et la durée du cycle de lavage.
6. PERSONNALISER LE CYCLE DE LAVAGE. Agir
sur les touches correspondantes du tableau de bord:
Modifier la température et/ou lessorage.
Lappareil sélectionne automatiquement la
température et lessorage maximaux prévus pour
le programme sélectionné qui ne peuvent par
conséquent pas être augmentés. Par pression sur
la touche
on peut diminuer progressivement la
température de lavage jusquà un lavage à froid
OFF. Par pression sur la touche
on peut
diminuer progressivement la vitesse dessorage
jusquà sa suppression totale OFF. Une autre
pression sur les touches ramènera les valeurs aux
maximums prévus.
Exception: lors de la sélection du programme
COTON BLANC la température peut être
augmentée jusquà 90°.
Sélectionner un départ différé.
Pour programmer le départ différé d'un programme
sélectionné, appuyer sur la touche correspondante
jusqu'à ce que le retard désiré soit atteint. Quand
cette option est activée, l'écran affiche le symbole
. Pour annuler le départ différé, appuyer sur la
touche jusqu'à ce que l'écran affiche OFF; le
symbole
s'éteindra.
Modifier les caractéristiques du cycle.
Appuyer sur la touche pour activer l'option,
l'écran affiche le nom de l'option et le croissant
de lune correspondant à la touche s'allume.
Appuyer une nouvelle fois sur la touche pour
désactiver l'option, l'écran affiche le nom de
l'option plus OFF et le croissant de lune s'éteint.
Si l'option sélectionnée est incompatible avec le
programme sélectionné, le croissant de lune se
met à clignoter et l'option n'est pas activée.
Si l'option sélectionnée est incompatible avec une
autre option précédemment sélectionnée, le
croissant de lune correspondant à la première
option se met à clignoter et seule la deuxième
option est activée alors que le croissant de lune de
l'option activée s'allume au fixe.
Les options permettent de modifier le chargement
conseillé et/ou la durée du cycle de lavage.
7. DEMARRER LE PROGRAMME. Appuyer sur la
touche START/PAUSE. Le voyant correspondant
s'allume au fixe et la porte hublot est verrouillée
(voyant PORTE VERROUILLEE
allumé). Pendant
le lavage, l'écran affiche le nom de la phase en
cours et les icônes correspondant aux phases
s'allument. Pour changer un programme tandis
quun cycle est en cours, activer une pause du
lave-linge par pression sur la touche START/PAUSE;
sélectionner enfin le cycle désiré et appuyer à
nouveau sur la touche START/PAUSE. Pour ouvrir la
porte tandis quun cycle est en cours, appuyer sur
la touche START/PAUSE; si le voyant PORTE
VERROUILLEE
est éteint, on peut ouvrir la
porte. Pour faire redémarrer le programme
exactement à lendroit de larrêt, appuyer une
nouvelle fois sur la touche START/PAUSE.
8. FIN DU PROGRAMME. Elle est signalée par
linscription END allumée. La porte hublot peut
alors être ouverte aussitôt. Si le voyant START/
PAUSE clignote, appuyer sur la touche pour
terminer le cycle. Ouvrir la porte, vider le lave-
linge et éteindre lappareil.
Une pression prolongée sur la touche permet
dannuler un cycle déjà lancé. Le cycle est
interrompu et lappareil séteint.
SACHET POUR EDREDONS, RIDEAUX ET
VETEMENTS DELICATS
Grâce au sachet spécial fourni avec l'appareil,
Ariston vous permet de laver à la machine même
vos vêtements plus délicats et précieux en assurant
au maximum leur protection.
Nous recommandons en tout cas d'utiliser le sachet
pour le lavage d'édredons et de couettes avec
housse réalisée dans un matériau synthétique.
F
19
Icône Description du Programme
Te m p .
maxi
C)
Vitesse
maxI
(tours
minute)
Produits
lessiviels
Charge maxi
(Kg)
Durée cycle
Lavage
Adoucis-
sant
Normal
Avec
charge
mini
Programmes pour tous les jours
COTON BLANC
60°
(Maxi 90°)
1400
ll
94
COTON BLANC: Blancs et couleurs délicates très sales.
40° 1400
ll
94
COTON COULEUR
40° 1400
ll
94
SYNTHETIQUE LICAT
40° 800
ll
42
MIX 30': pour rafraîchir rapidement du linge peu sale (ne
convient pas pour la laine, la soie et le linge à laver à la main).
30° 800
ll
3,5 1, 5
Programmes énergiques
PRÉLAVAGE : pour enlever les taches tenaces.
(Ajouter le produit lessiviel dans le bac prévu)
.
90° 1400
ll
94
SYNTHETIQUE RÉSISTANT
60° 800
ll
42
Programmes spéciaux
CHEMISES
40° 600
ll
21
SOIE: pour linge en soie, viscose, lingerie.
30° 0
ll
21
LAINE: pour laine, cachemire, etc.
40° 600
ll
21
DUVETS: pour linge et vêtements en duvet d'oie.
30° 1200
ll
31, 5
LIT ET BAIN 7JOURS: pour le linge de lit et le linge de toilette.
60° 1400
ll
94
Programmes partiaux
Rinçage textiles résistants - 1400 -
l
94
Rinçage textiles délicats - 800 -
l
42
Essorage textiles résistants - 1400 - - 94
Essorage textiles délicats - 800 - - 42
Vidange - 0 - - 94
Options de lavage
Super Lavage
Grâce à lutilisation dune plus grande quantité deau
au cours de la phase initiale du cycle et à une durée
prolongée de ce dernier, cette option permet
dobtenir un lavage très performant.
Cette option nest pas activable avec les programmes
Mix 30, Soie, Laine, Duvets et Programmes partiaux.
Repassage facile
En cas de sélection de cette option, le lavage et
lessorage seront dûment modifiés pour réduire la
formation de plis. A la fin du cycle de lavage, le lave-
linge fait tourner le tambour lentement; les voyants
Repassage facile et START/PAUSE se mettent à
clignoter. Pour finir le cycle, appuyer sur la touche
START/PAUSE ou sur la touche Repassage facile.
Pour le programme Soie lappareil arrive au bout du
cycle en laissant le linge tremper, le voyant
Repassage facile clignote. Pour vidanger leau et
pouvoir sortir le linge, il faut appuyer sur la touche
START/PAUSE ou sur la touche Repassage facile.
Cette option nest pas activable avec les
programmes Laine, Essorage textiles résistants,
Essorage textiles délicats et Vidange.
Rinçage Plus
La sélection de cette option permet daugmenter
lefficacité du rinçage et éliminer totalement toute
trace de lessive. Elle est très utile pour les personnes
particulièrement sensibles aux produits lessiviels. Son
utilisation est conseillée en cas de pleine charge ou
de doses élevées de produit lessiviel.
Cette option nest pas activable avec les
programmes Mix 30, Essorage textiles résistants,
Essorage textiles délicats et Vidange.
Charge mini
Cette fonction est conseillée quand la charge de linge
est inférieure ou égale à la moitié de la charge maxi.
conseillée (voir Tableau des programmes).
Cette option nest pas activable avec les
programmes Essorage textiles résistants, Essorage
textiles délicats et Vidange.
Les données dans le tableau sont reprises à titre indicatif.
Programmes et options
Tableau des programmes
La durée du cycle de lavage peut être visualisée sur le display.
20
F
Produits lessiviels et linge
Lessive
Le choix et la quantité de lessive dépendent du type
de textile (coton, laine, soie...), de la couleur, de la
température de lavage, du degré de salissure et de la
dureté de leau.
Bien doser la quantité de produit lessiviel évite des
gaspillages et protège lenvironnement: bien que
biodégradables, les produits lessiviels contiennent des
éléments qui altèrent léquilibre de la nature.
Il est conseillé de:
utiliser des lessives en poudre pour le linge en
coton blanc et pour le prélavage.
utiliser des lessives liquides pour linge délicat en coton
et pour tous les programmes basse température.
utiliser des lessives liquides délicates pour la laine
et la soie.
Ne pas utiliser de lessives pour lavage à la main,
elles génèrent trop de mousse.
Le produit lessiviel doit être versé juste avant le
démarrage du lavage dans le bac prévu à cet effet ou
dans la boule doseuse directement dans le tambour.
Dans ce cas, le cycle Coton avec Prélavage nest
pas sélectionnable.
Triage du linge
Bien déplier le linge avant de l'introduire dans la
machine.
Trier le linge selon le type de textile (symbole sur
létiquette du vêtement) et la couleur en veillant à
bien séparer le linge couleur du linge blanc;
Vider les poches et contrôler les boutons;
Ne pas dépasser les valeurs indiquées dans le Tableau
des Programmes correspondant au poids de linge sec.
Combien le linge pèse-t-il ?
1 drap 400-500 g
1 taie doreiller 150-200 g
1 nappe 400-500 g
1 peignoir 900-1200 g
1 serviette de toilette 150-250 g
1 jeans 400-500 g
1 chemise 150-200 g
Conseils de lavage
Chemises: sélectionner le programme approprié au
lavage de chemises de textile et couleur différents. Il
en prendra le plus grand soin.
Soie: sélectionner le programme de lavage spécial
vêtements en soie. Il est conseillé dutiliser une
lessive spéciale pour linge délicat.
Rideaux: nous recommandons de les plier et de les
mettre dans le sachet fourni avec la machine. Utilisez le
programme "Soie".
Laine: Ariston est le seul lave-linge à avoir obtenu le
prestigieux label Woolmark Platinum Care (M.0508) délivré
par The Woolmark Company qui garantit le lavage à la
machine de tous les vêtements en laine, y compris ceux qui
portent létiquette lavage à la main uniquement
.
Grâce au programme Laine on peut donc laver à la
machine, en toute tranquillité, tous les vêtements en laine
avec des performances de lavage garanties.
Duvets: pour laver des articles avec garnissage en
duvet d'oie comme par exemple des couettes deux
places ou une place (poids maximal à ne pas
dépasser 3 kg), oreillers, anoraks, utiliser le
programme spécial "Duvets". Pour introduire les
duvets dans le tambour, nous recommandons de
replier les bords en dedans (voir figures) et de ne pas
occuper plus de ¾ du volume du tambour.
Pour un lavage optimal, nous recommandons
d'utiliser une lessive liquide à doser dans le tiroir à
produits lessiviels.
Edredons: pour laver les édredons avec housse
synthétique, utilisez le sachet spécial fourni avec la
machine et sélectionnez le programme "Duvets".
Linge de toilette et de lit: ce lave-linge permet de
laver tout le linge de maison de la semaine en un seul
cycle Lit et Bain 7 Jours qui optimise lutilisation de
lassouplissant et permet de faire des économies de
temps et délectricité. Nous conseillons dutiliser de la
lessive en poudre.
Taches tenaces: mieux vaut traiter les taches tenaces
avec du savon solide avant le lavage et sélectionner
ensuite le programme Coton avec Prélavage.
Système déquilibrage de la charge
Avant tout essorage, pour éviter toute vibration excessive
et répartir le linge de façon uniforme, le lave-linge fait
tourner le tambour à une vitesse légèrement supérieure à
la vitesse de lavage. Si au bout de plusieurs tentatives, la
charge nest toujours pas correctement équilibrée,
lappareil procède à un essorage à une vitesse inférieure
à la vitesse normalement prévue. En cas de déséquilibre
excessif, le lave-linge préfère procéder à la répartition du
linge plutôt quà son essorage.
Pour aider à une meilleure répartition de la charge et à
un bon équilibrage, nous conseillons de mélanger de
grandes et petites pièces de linge.
1 / 1

Indesit AQXGD 149 S (EX) Mode d'emploi

Catégorie
Machines à laver
Taper
Mode d'emploi

dans d''autres langues