Honeywell BTM1 Mode d'emploi

Taper
Mode d'emploi
User Guidance for Module BTM1
FCC ID: HD5-BTM1; IC: 1693B-BTM1
1. Introduction
Product Marketing NameBT Module
Module Model Name: BTM1
This module BTM1 is Bluetooth (BT) module which is compliant with the BT
specification BR/BLE.
2. Electrical
Chipset: The module main chipset: SKY66407-11, BR8051A01, H2U34C1H1B0100
Supply: The module source all required power from a 3.3V +/- 0.1V input supply.
3. Environmental
Operating Temperature: The module operate across the temperature range of -30°to
50°Celsius
4. Conditions on using module BTM1:
Customer must ensure that its product (the “Customer Product”) is electrically
identical to module BTM1. Customer acknowledges that any modifications to
module BTM1 may invalidate regulatory approvals in relation to the Customer
Product, or may necessitate notifications to the relevant regulatory authorities.
OEM must inform us of any changes which may require the Class I or Class II
permissive changes for the FCC. Any substituted antenna and RF cable
assemblies must be approved in order to maintain compliance FCC rules.
5. Regulation information:
5.1 USA—Federal Communications Commission (FCC)
FCC Compliance Statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Information to User:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy. If not installed and
used in accordance with the instructions, it may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by tuning the equipment off and on, the
user is encouraged to try and correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna
-Increase the distance between the equipment and the receiver.
-Connect the equipment to outlet on a circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20 cm between the radiator and your body.
System integrators must include the FCC ID on the end product.
5.2 Canada - Industry Canada (IC)
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s)
l'opération est soumise aux deux conditions suivantes: . ( 1) cet dispositif ne doit pas
causer d'interférences et ( 2) cet appareil doit accepter toute interférence , y compris
les interférences qui peuvent provoquer un mauvais fonctionnement de l'appareil.
RF Exposure statement
Radiation Exposure statement:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20 cm between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies
pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec
un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
System integrators must include a label with “Contains IC: 1693B-BTM1” on the end
product.
Les intégrateurs système doivent inclure une étiquette indiquant “ Contient IC :
1693B-BTM1” sur le produit final.
5.3 Europe - EU Restrictions
This equipment needs to be marked with the symbol and can be used
throughout the European community.
Exposure to Radio Frequency Radiation
To comply with RF exposure compliance requirements, for mobile configurations, a
separation distance of at least 20cm must be maintained between the antenna of this
device and all persons.
Note for system integrators:
- The module is tested to comply with Directive 2014/53/EU. System integrators are
responsible for compliance of the final device with the RED Directive.
- Packaging: CE Marking must also be on the outer packaging of the product. The
outer packaging must also provide an indication as to where the device is intended to
be used and OR conversely, where there may be restrictions for use.
Support Wireless Frequency
Frequency Band
PowerMax e.i.r.p
BT 5.02402-2480MHz
8.56dBm
  • Page 1 1
  • Page 2 2
  • Page 3 3

Honeywell BTM1 Mode d'emploi

Taper
Mode d'emploi

dans d''autres langues