Modern Forms WS-53932 Gatsby Mode d'emploi
- Taper
- Mode d'emploi
1
INSTALLATION INSTRUCTIONS
539-Indoor Wall Sconce
WS-53932
HARDWARE
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Feb 2019
ANUARY, 2017
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
CAUTION: To prevent electrical shock, ensure electricity has been turned off at the circuit breaker before beginning.
•Read all instructions before installing.
•System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
•When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
•Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by dweLED. Substitution of parts or accessories not designated for use with this product by dweLED could
result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are
damaged or missing.
MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that customers in coastal
areas clean all external surfaces of the fixture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
•Lisez toutes les instructions avant l’installation.
•Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
•Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits dweLED. Remplacer des pièces ou accessoires non conçus pour ce
produit dweLED pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez
contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
un chiffon humide.
Wood Screw
Qty: 2pcs+1Extra
5/32-16×1
Mounting Screw
Qty: 1 Extra
5/32-32×1/2
Plastic Anchor
Qty: 2pcs+1Extra
Wire Connector
Qty: 3pcs+1Extra
Mounting Screw
Qty: 1 Extra
5/32-32×2 1/6
AB
C D E F
Mounting Screw
Qty: 1 Extra
5/32-32×1/5
2
INSTALLATION INSTRUCTIONS
539-Indoor Wall Sconce
WS-53932
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
FIG. 2 Wiring
FIG. 1
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Feb 2019
ANUARY, 2017
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
PREPARATION
1. Shut off the power at the circuit breaker and
remove existing fixture, including the crossbar.
2. Carefully unpack your new fixture and lay out
all the parts on a clear area. Be careful not to
lose any small parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screw (B) and back
plate from the fixture.
4. Drill holes in the wall aligned with the key
hole located in the mounting plate, insert
the plastic anchor (C).
5. Secure the mounting plate to the switch box
using junction box screws, fasten assembly to the wall
using wood screw (D).
NOTE: The side of the mounting plate marked “GND”
must face out.
6. Remove the mounting screw (E ) and loosen the
junction box screw (F).
7. Insert the mitered glass and secure it with end fixed
block by pushing back the end fixed block, fasten
the mounting screw (E), tighten the mounting screw (F).
8. Tear off the protective film on the wall box.
CONNECTING THE WIRES (Fig. 2)
9. Connect the fixture’s wires to junction box wires as shown (Fig. 2). Make sure that all wire connectors (A) are secure. If your outlet box
has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the
back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
COMPLETING THE INSTALLATION
10. Secure the fixture to the mounting back plate using the mounting screw (B) .
Mounting Screw
Wire Connector
Junction Box Screw
Ground Wire Wood Screw
Plastic An
ch
or
Mitered Glass
(WS-53932/WS-53932F: RPL-GLA-53932)
End Fixed Block
Junction Box
Mounting Back Plate
Mounting Screw
B
A
C
D
E
Mounting Screw
F
Back Plate Dimensions
WS-53932(7MBC631201)
21 5/8”
4 7/8”
1 3/4”
1 3/8”
24 7/8”
-
1
-
2
Modern Forms WS-53932 Gatsby Mode d'emploi
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
Modern Forms BL-54307 Nexus Mode d'emploi
-
-
-
-
-
-
-
-
-
WAC Lighting FM-W47205-40-BK Mode d'emploi