NutriBullet NB-50200 Mode d'emploi

Catégorie
Mélangeurs
Taper
Mode d'emploi

Ce manuel convient également à

User guide.
®
SELECT
3
GENERAL SAFETY
INFORMATION
Close supervision is necessary
when any appliance is used
by or near children. Keep cord
out of reach of children. This
appliance is not a toy. Do not
allow children to play with it.
NEVER LEAVE THE
NUTRIBULLET® UNATTENDED
WHILE IT IS IN USE
 DO NOT USE OUTDOORS
 ALWAYS TURN THE
NUTRIBULLET® OFF WHEN
NOT IN USE
HEAT & PRESSURE
SAFETY
• Always use extreme care
and attention when using hot
ingredients in any blending
product, as the friction from
the rotating blades (during the
blending process) combined
with the thermal energy of the
heated ingredients can create
a dangerous situation if not
properly controlled.
Important safeguards.
Warning! To avoid the risk of serious injury, carefully read all
instructions before operating your NutriBullet®. When using any
electrical appliance, basic safety precautions should always be
observed, including the following important information.
Save these instructions!
FOR HOUSEHOLD USE ONLY
!
BLENDING WITH
NUTRIBULLET
®
CUPS:
To avoid personal
injury, never blend hot
ingredients or liquid in any
sealed NutriBullet® cup!
Heated ingredients can
pressurize sealed containers
when agitated and cause
cup and blade separation or
violently expel hot contents
upon opening. Always
start the blending process
with room temperature or
refrigerated ingredients and
liquids (21°C/70°F or cooler).
Never continuously operate
for longer than necessary
to create your recipe —
generally less than one
minute. Blade friction
from prolonged operation
can heat ingredients and
generate internal pressure
in the sealed container. This
pressure can cause the cup
and blade to separate or
blended contents to erupt
WARNING!
54
from the container, resulting
in possible personal injury
and/or property damage.
If the sealed NutriBullet®
cups are warm to the touch,
power o your machine
and allow the vessel to cool
for fifteen minutes or more.
Allow contents to settle
before slowly releasing the
cup from the motor base.
With the NutriBullet® cup,
pointed away from your face
and body, slowly unscrew the
easy-twist extractor blade
to gently release any
residual pressure.
If you need to blend for
longer than one minute,
blend for 1-minute intervals.
After each 1-minute interval,
allow the motor base to shut
o completely and wait at
least one minute before
starting the next cycle. Do
not run for more than 3
consecutive 1-minute intervals
to prevent the contents from
overheating. Allow contents
to settle for 2-3 minutes after
the third blending cycle to
prevent overheating and
buildup of pressure.
Sugar in fruits and vegetables
can ferment over time,
releasing gases that cause
pressure to build up in a
sealed NutriBullet® cup. Do
not store any smoothies or
blended mixtures in vessels
sealed with the easy-twist
extractor blade. If you will
not consume your smoothie
immediately, remove the
easy-twist extractor blade
and cover your NutriBullet®
cup with plastic wrap before
refrigerating. If your smoothie
or blended mixture was
made in the pitcher, transfer
to another storage container
before refrigerating. Never
store any blended mixture in
a sealed cup unrefrigerated,
or for any prolonged period
of time; contents will spoil and
ferment, producing gases that
might cause eruption.
Never blend carbonated
liquids, reactive, or
eervescing ingredients
(e.g., baking soda, baking
powder, vinegar, cirtric acid,
yeast, etc.). Pressure from
released gases can cause a
sealed blending container to
burst or separate, resulting
in possible injury and/or
property damage.
BLENDING WITH THE PITCHER:
Use extra caution when
blending hot liquids in
the pitcher.
Never turn the power on
while using the pitcher
without the vented lid cap
inserted and locked into the
pitcher lid, as ingredients
can splash, and if hot or
warm, could potentially
WARNING!
WARNING!
cause thermal injury and/or
property damage.
Steam and splattering
ingredients can escape
through the pitcher lid,
potentially scalding and/
or burning the user. NEVER
blend hot liquids in your
pitcher without the pitcher
lid and vented lid cap locked
into the pitcher lid and
attached. The vented lid cap
allows steam and pressure
to escape, while guarding
against excess splashing.
NEVER blend hot liquids in
your NutriBullet® cups or any
other sealed vessel.
When blending hot liquids,
add liquid and solid
ingredients to your pitcher
below their respective MAX
lines. Attach the pitcher
lid with the vented lid cap
inserted and locked. Press
POWER and begin blending
on the LOW setting. Once
ingredients are integrated,
increase speed as needed.
If the NutriBullet® blends
for longer than one minute,
friction from the blades can
cause ingredients to heat and
generate internal pressure
inside the vessel. If a blending
vessel becomes warm to the
touch, turn o the machine
and allow the vessel to cool
completely before carefully
opening, pointed away from
your body to avoid injury.
BLADE SAFETY
Never store any easy-twist
extractor blade in the
motor base unattached
to a NutriBullet® cup. An
exposed blade can present
a laceration hazard.
Blades are sharp! Handle
carefully. Use care when
handling any blade. To
avoid laceration injury, do
not handle or touch any
blade edge.
AVOID CONTACT WITH
MOVING PARTS! Keep hands
and utensils out of and away
from blades while blending
food to reduce the risk of
severe personal injury.
TO REDUCE THE RISK OF
PERSONAL INJURY OR
PROPERTY DAMAGE, make
sure the easy-twist extractor
blade is securely twisted
(hand-tightened) onto the
NutriBullet® blending vessel
before placing it on the
motor base and operating
the NutriBullet® Select. Check
to make sure the easy-twist
extractor blade is aligned
properly before placing it on
the motor base and operating
your NutriBullet® Select.
After blending, turn the power
blending vessel/easy-twist
extractor blade assembly
from the motor base until
the motor comes to a full
stop and the unit powers
WARNING!
WARNING!
76
down completely. Taking the
blending vessel o the unit
prior to complete power down
can cause damage to the
easy-twist extractor blade
coupling or motor gear.
Never use the NutriBullet®
Select without adding
liquid, as doing so may
damage the blades.
The cyclonic action® of your
NutriBullet® Select requires
the use of liquids to make
smoothies and other nutritious
items. The NutriBullet® Select
is not intended to be used
without liquids, or as an ice
crusher. ALWAYS ADD LIQUID
to your recipe.
DO NOT USE the easy-twist
extractor blade for grinding
dry ingredients such as grains,
cereal, or coee, as this may
damage the motor and/or the
easy-twist extractor blade.
We recommend replacing your
easy-twist extractor blade
every 6 months (depending
on use) or as needed for
optimal performance.
PITCHER SAFETY
Ensure the easy-twist
extractor blade is securely
fastened to the pitcher base
before blending. Failure to
properly align the blade
and pitcher attachment can
cause liquid to leak out of
the base, potentially causing
the components to separate
during blending. This can
result in damage to the
machine, damage to property,
and/or personal injury.
With recipes that require
certain ingredients to be
incorporated during blending,
first add the base ingredients,
seal the pitcher lid with vented
lid cap attached, and begin
blending. Then, once the
ingredients are well mixed,
twist open the vented lid cap
and carefully pour or drop
ingredients into the mixture.
If you need to push ingredients
closer to the blade, ONLY
USE THE TAMPER PROVIDED
with the NutriBullet® Select.
DO NOT use any utensil or
apparatus other than the
tamper to push ingredients
toward the blade. The tamper
is specifically designed not
to come in contact with the
blade. Spatulas, spoons
and other tools can make
contact with the blade, which
may result in damage to the
machine, damage to property,
and/or possible injury.
NEVER USE YOUR FINGERS
OR ANY PART OF YOUR HAND
TO PUSH INGREDIENTS
DOWN TOWARD THE BLADE.
Only use the provided tamper.
Remember to use extra
caution when blending hot
liquids or ingredients in
the pitcher.
Spray or escaping steam
may cause burns and/or
property damage.
Do not fill container above
the maximum capacity lines
indicated for liquids and
solid ingredients.
Always begin blending hot
ingredients on the LOW setting.
Keep hands and other exposed
skin away from lid opening to
prevent possible burns.
ELECTRICAL SAFETY
Do not use this product
in locations with dierent
electrical specifications or
plug types. Do not operate
with any type of plug
adapter or voltage converter
device, as these may cause
electrical shorting, fire,
electric shock, personal
injury, or product damage.
The use of attachments,
including canning jars, is
not recommended and may
cause fire, electric shock,
personal injury, or product
damage and will void the
product’s warranty.
To avoid the risk of electric
shock, never immerse the
cord, plug, or motor base of
the NutriBullet® Select in water
or other liquids. Discontinue
use if the cord, plug, or motor
base is damaged.
Always POWER OFF and
UNPLUG the NutriBullet®
Select when it is not in use
or BEFORE assembling,
disassembling, changing
accessories, or cleaning. Do
not attempt to handle the
NutriBullet® Select until all
parts have stopped moving.
Do not allow the cord to
hang over the edge of the
table or counter. Do not
pull, twist, or damage the
power cord. Do not allow the
cord to touch hot surfaces,
including the stove.
If the motor stops working,
unplug the motor base and let
it cool for at least 15 minutes
before attempting to use
it again. Your NutriBullet®
Select has an internal thermal
breaker that shuts o the
motor when it overheats. The
thermal breaker will reset
when the unit is unplugged,
and the thermal breaker cools
down suciently.
POLARIZED PLUG INFORMATION:
This appliance has important
markings on the plug. The
attachment plug or entire
cord set is not suitable for
replacement. If damaged, the
appliance will be replaced.
Your NutriBullet® Select has
a polarized plug (one prong
is wider than the other) to
reduce the risk of electric
shock. This plug will correctly
fit in a polarized outlet only
one way. If the plug does not
fit fully in the outlet, reverse
the plug. If it still does not fit,
contact a qualified electrician.
WARNING!
WARNING!
WARNING!
98
For your safety, do not modify
the plug or motor base in any
way. Doing so will increase
risk of injury and void the
product’s warranty.
STOVETOP
HEATING SAFETY
Do not blend hot
ingredients in any sealed
NutriBullet® cup!
To heat items that have been
blended at room temperature
or cooler (21°C/70°F or
less), transfer mixture to a
stovetop pot to heat. Use
a thermometer to test the
internal temperature of
cooked ingredients; they may
feel cool to the touch, yet still
be hot inside.
The NutriBullet® Select is not
intended for use on the stove
top. Do not place the motor
base or any NutriBullet®
accessory on the stove or
microwave or immerse in
boiling water. This may result
in damage to the accessory.
VENTILATION WARNINGS
To prevent a fire hazard,
power base openings
(underneath the motor base)
should be free of dust and
lint and never obstructed
with flammable materials
such as newspapers,
tablecloths, napkins,
dishtowels, place mats or
other similar type materials.
CAUTION! Always operate the
NutriBullet® Select on a level
surface, leaving unobstructed
space beneath and around
the motor base to permit
proper air circulation. Vents
on the bottom of the product
are provided for ventilation
to ensure reliable motor
operation and to
prevent overheating.
MEDICAL SAFETY
The information contained
in this User Guide or Recipe
Guide is not meant to replace
the advice of your physician.
Always consult your physician
regarding health and
nutrition concerns.
MEDICATION INTERACTIONS:
If you are taking any
medication, especially
cholesterol-lowering
medication, blood
thinners, blood pressure
drugs, tranquilizers, or
antidepressants, please
check with your physician
before trying any of the
recipes contained in this
guide or the recipe guide.
Avoid blending the following
seeds and pits in the
NutriBullet® Select, as they
contain a chemical known to
release cyanide into the body
when ingested: apple seeds,
cherry pits, plum pits, peach
pits, and apricot pits. Fruit
pits may also cause damage
to the pitcher.
WARNING!WARNING!
ADDITIONAL
INSTRUCTIONS FOR
PROPER USAGE
Do not place any of the
NutriBullet® Select parts in
a microwave, oven, or in a
stovetop pot, or immerse in
boiling water, as this may
result in damage to the part.
TO AVOID LEAKAGE, DO
NOT OVERFILL THE
BLENDING VESSELS! The
pitcher is marked with two
MAX lines: one for solid
ingredients (higher line) and
one for liquid ingredients
(lower line). Your NutriBullet®
cups are also marked with
a MAX line. When filling
the blending vessels, make
sure your ingredients do not
exceed their respective MAX
lines. Exceeding the indicated
MAX lines can result in
leakage, and may lead to
dangerous pressurization.
Blending vessels and easy-
twist extractor blades
are specific to the exact
model of NutriBullet®
Select you possess. Use of
incompatible parts (parts
from other models) may
result in damage to your
NutriBullet® Select or create
safety hazards. When
ordering replacement parts
(NutriBullet® cups, pitcher,
easy-twist extractor blades)
on nutribullet.com or via
customer service, please
specify the machine model to
ensure you receive parts that
are compatible with your unit.
Periodically inspect
all NutriBullet® Select
components for damage
or wear that may impair
proper function or present an
electrical hazard. Make sure
that the power cord and plug
are undamaged. Discontinue
use and replace blending
vessels if you detect cracking,
cloudiness, or damage to
the plastic. Ensure that the
blades rotate freely and that
the structure is undamaged.
Make sure that the motor
base is unobstructed and
clean. Follow maintenance
recommended in the User
Guide and never operate
your NutriBullet® Select with
damaged components.
If your NutriBullet® Select
malfunctions in any way,
immediately discontinue use
and contact customer service
at 1-800-523-5993. You may
purchase new NutriBullet®
cups, pitchers, and easy-
twist extractor blades
at nutribullet.com or by
contacting customer service.
Save these
instructions!
If you have any comments,
questions, or concerns, please
go to nutribullet.com.
Or call customer service at:
1-800-523-5993.
!
1110
Contents.
12 Whats included
13 Assembly guide
14 Getting started
14 Safety guide
15 Pitcher assembly & use
18 NutriBullet® cup assembly & use
20 Blending control panel.
21 How to use the blending control panel
22 Care & maintenance.
22 How to clean the NutriBullet®
24 How to store
24 Replacement parts
25 NutriBullet® Select
one-year limited warranty
28 Warranty Registration
Thank you for purchasing the NutriBullet® Select.
1312
What’s included. Assembly guide.
32-oz pitcher
tamper
pitcher lid with
vented lid cap
motor base
24-oz
handled cup to-go lid
easy-twist
extractor blade
NutriBullet®
cup
vented lid cap
pitcher lid
pitcher
tamper
easy-pour spout
blending control
panel
motor base
suction cup feet
easy-twist
extractor blade
15
Use extra caution when
blending hot liquids in
the pitcher.
Steam and splatters can escape
through the vented lid, potentially
causing scalding and/or burns.
NEVER blend hot liquids in your
pitcher without the pitcher lid
and vented lid cap attached. The
vented lid cap is ventilated to allow
steam and pressure to release,
while guarding against excess
splashing. NEVER blend hot liquids
in your Nutribullet cups or any
other sealed vessel.
When blending hot liquids, add
liquid and solid ingredients to your
pitcher below their respective
MAX lines. Attach the pitcher lid
with the vented lid cap inserted.
Press the POWER icon, then begin
blending on the LOW setting. Once
ingredients are integrated and
the mixture is level (no splashing),
increase speed as needed.
PLEASE KEEP THESE
IMPORTANT SAFEGUARDS IN
MIND WHEN USING
THE APPLIANCE:
Make sure the base is plugged in
for use.
DO NOT attempt to operate the pitcher
on the appliance without attaching
the pitcher lid and vented lid cap.
Never run the appliance while empty.
Appliance accessories are not
intended to be used in the microwave
as it may damage the accessories.
Never leave the appliance
unattended while in use.
Never blend hot ingredients
when using any sealed
NutriBullet® cups.
Heated ingredients can pressurize
sealed containers when agitated
and violently expel hot contents upon
opening. Always start the blending
process with room temperature or
refrigerated ingredients and liquids
(21°C/70°F or cooler).
WARNING!
WARNING!
Getting started.
Pitcher assembly
& use.
1 Review all warning and
caution statements in the
Important Safeguards
section (pg 3-9) and on
the previous page before
proceeding to Step 2.
2 Place the motor base on
a clean, dry, level surface
such as a counter or table.
Place the pitcher onto the
motor base and gently twist
clockwise so it locks in place.
When you hear the click, it’s
locked and ready to blend.
NOTE: If you are left-handed, place
the handle facing towards the center
of the blending control panel and
twist clockwise.
Twist the easy-twist
extractor blade onto the
base of the pitcher, making
sure the components are
properly aligned and
securely fastened.
6
3
4
Place the pitcher on a
clean, dry, level surface
such as a counter or table.
Add the ingredients to the
pitcher, making sure they do
not exceed the MAX line.
NOTE: The blending pitcher is
marked with two MAX lines: one for
solid ingredients (higher line) and
one for liquids (lower line). When
filling the blender, make sure your
ingredients do not exceed their
respective MAX lines.
5
Place the pitcher lid with
vented lid cap attached on
the pitcher, making sure it’s
aligned to the handle.
14
1716
If the ingredients stick to
the side of the pitcher,
press POWER to stop the
appliance and wait for the
blade to stop turning. Then
remove the pitcher lid and
use the tamper to dislodge
the ingredients. When
finished, replace the lid and
continue blending. If the
ingredients continue to stick,
consider adding more liquid.
7
Plug the power cord into
an electrical outlet and
press POWER to turn on
the blender.
9
8
To start blending, select
a speed or the EXTRACT
program on the blending
control panel. This program
will turn o automatically.
Buttons illuminate while in use.
NOTE: Proceed to the blending
control panel chart on page 20 for
speed definitions.
Twist pitcher counterclockwise
and lift o the motor base.
Pour and enjoy!
Press POWER to turn o
the unit completely.
When you have reached
your desired consistency,
pause/stop the appliance
by pressing POWER or the
speed you selected and wait
for the blades to stop turning.
The unit will enter idle-mode.
The POWER button will
remain illuminated.
WARNING: Blades are sharp. Never
insert your hands into the pitcher.
10
12
11
CAUTION: Do not use any
apparatus or utensil other than
the tamper to push ingredients
toward the blade. The tamper
is specifically designed not to
come in contact with the blade.
Spatulas, spoons and other
tools are long enough to reach
the blade, which may result in
damage to the machine, damage
to property, and possible injury.
NOTE: If you need to add
additional ingredients while
blending, switch the setting to
LOW and remove the vented
lid cap from your pitcher lid,
leaving the lid attached. Add
ingredients through the hole
in the top of the lid, followed
by the tamper if necessary.
Replace the vented lid cap, then
increase to your desired speed.
DO NOT attempt to add items
through the vent hole when
blending hot ingredients.
If the ingredients stick to
the side of the pitcher,
press POWER to stop the
appliance and wait for the
blade to stop turning. Then
remove the pitcher lid and
use the tamper to dislodge
the ingredients. When
finished, replace the lid and
continue blending. If the
ingredients continue to stick,
consider adding more liquid.
7
Plug the power cord into
an electrical outlet and
press POWER to turn on
the blender.
9
8
To start blending, select
a speed or the EXTRACT
program on the blending
control panel. This program
will turn o automatically.
Buttons illuminate while in use.
NOTE: Proceed to the blending
control panel chart on page 20 for
speed definitions.
Twist pitcher counterclockwise
and lift o the motor base.
Pour and enjoy!
Press POWER to turn o
the unit completely.
When you have reached
your desired consistency,
pause/stop the appliance
by pressing POWER or the
speed you selected and wait
for the blades to stop turning.
The unit will enter idle-mode.
The POWER button will
remain illuminated.
WARNING: Blades are sharp. Never
insert your hands into the pitcher.
10
12
11
CAUTION: Do not use any
apparatus or utensil other than
the tamper to push ingredients
toward the blade. The tamper
is specifically designed not to
come in contact with the blade.
Spatulas, spoons and other
tools are long enough to reach
the blade, which may result in
damage to the machine, damage
to property, and possible injury.
NOTE: If you need to add
additional ingredients while
blending, switch the setting to
LOW and remove the vented
lid cap from your pitcher lid,
leaving the lid attached. Add
ingredients through the hole
in the top of the lid, followed
by the tamper if necessary.
Replace the vented lid cap, then
increase to your desired speed.
DO NOT attempt to add items
through the vent hole when
blending hot ingredients.
18
Handle the easy-twist extractor
blade assembly with care, as
the blades are sharp.
Never leave the appliance
unattended while in use.
NEVER BLEND HOT
INGREDIENTS, as doing so
may cause excessive pressure
buildup, resulting in risk
of personal injury and or
property damage.
NutriBullet® cup
assembly & use.
WARNING!
Plug the power cord into
an electrical outlet and
press POWER to turn on
the blender.
5
Add ingredients to
the NutriBullet® cup.
NOTE: Do not overfill! To avoid
leakage, do not add ingredients
beyond the MAX line.
3
4
Twist the easy-twist
extractor blade onto the
cup until tightly sealed.
1 Review all warning and
caution statements in the
Important Safeguards
section (pg 3-9) before
proceeding to Step 2.
2 Place the motor base on
a clean, dry, level surface
such as a counter or table.
6
Turn the cup upside down
and place it onto the motor
base, gently turning the
cup clockwise to lock into
the motor base.
7
8
10
To start blending, select
a speed or the EXTRACT
program on the blending
control panel. This program
will turn o automatically.
Buttons will illuminate while
in use.
NOTE: Proceed to the blending
control panel chart on page 20 for
speed definitions.
When you have reached
your desired consistency,
pause/stop the appliance
by pressing POWER or the
speed you selected and wait
for the blades to stop turning.
The unit will enter idle-mode.
The POWER button will
remain illuminated.
NOTE: speeds will automatically
shut o after 60 seconds.
Unlock the assembly by
gently twisting the cup
counterclockwise. You will
hear a click. Enjoy!
NOTE: Blending should not require
longer than one minute to yield
smooth and creamy results.
Press POWER to turn o
the unit completely.
9
CAUTION
Do not remove the easy-twist
extractor blade from the
NutriBullet® cup until blending
has completely ceased. Do not
use the easy-twist extractor blade
as a storage lid for your cup.
Some foods may contain active
ingredients or release gases that
will expand if left in a sealed
container, resulting in excessive
pressure buildup that can pose
a risk of injury. When storing
contents in the cup, use plastic
wrap or foil to seal your container.
Always point contents away from
your body when unsealing.
Handle the easy-twist extractor
blade assembly with care, as
the blades are sharp.
Never leave the appliance
unattended while in use.
NEVER BLEND HOT
INGREDIENTS, as doing so
may cause excessive pressure
buildup, resulting in risk
of personal injury and or
property damage.
NutriBullet® cup
assembly & use.
WARNING!
Plug the power cord into
an electrical outlet and
press POWER to turn on
the blender.
5
Add ingredients to
the NutriBullet® cup.
NOTE: Do not overfill! To avoid
leakage, do not add ingredients
beyond the MAX line.
3
4
Twist the easy-twist
extractor blade onto the
cup until tightly sealed.
1 Review all warning and
caution statements in the
Important Safeguards
section (pg 3-9) before
proceeding to Step 2.
2 Place the motor base on
a clean, dry, level surface
such as a counter or table.
6
Turn the cup upside down
and place it onto the motor
base, gently turning the
cup clockwise to lock into
the motor base.
7
8
10
To start blending, select
a speed or the EXTRACT
program on the blending
control panel. This program
will turn o automatically.
Buttons will illuminate while
in use.
NOTE: Proceed to the blending
control panel chart on page 20 for
speed definitions.
When you have reached
your desired consistency,
pause/stop the appliance
by pressing POWER or the
speed you selected and wait
for the blades to stop turning.
The unit will enter idle-mode.
The POWER button will
remain illuminated.
NOTE: speeds will automatically
shut o after 60 seconds.
Unlock the assembly by
gently twisting the cup
counterclockwise. You will
hear a click. Enjoy!
NOTE: Blending should not require
longer than one minute to yield
smooth and creamy results.
Press POWER to turn o
the unit completely.
9
CAUTION
Do not remove the easy-twist
extractor blade from the
NutriBullet® cup until blending
has completely ceased. Do not
use the easy-twist extractor blade
as a storage lid for your cup.
Some foods may contain active
ingredients or release gases that
will expand if left in a sealed
container, resulting in excessive
pressure buildup that can pose
a risk of injury. When storing
contents in the cup, use plastic
wrap or foil to seal your container.
Always point contents away from
your body when unsealing.
19
2120
HIGH SPEED
Use to liquefy thick
mixtures and blend frozen
fruits and vegetables.
EXTRACT
PULSE
HIGHLOW
EXTRACT
PULSE
HIGHLOW
EXTRACT
PULSE
HIGHLOW
EXTRACT
PULSE
HIGHLOW
EXTRACT
PULSE
HIGHLOW
LOW SPEED
Use to mix thin batter,
gravies, marinades; scramble
eggs; process cooked foods
and uncooked fruits.
EXTRACT
PULSE
HIGHLOW
EXTRACT
PULSE
HIGHLOW
EXTRACT
PULSE
HIGHLOW
EXTRACT
PULSE
HIGHLOW
EXTRACT
PULSE
HIGHLOW
Blending control panel.
TURNING ON/OFF
The power button actuates
the master power of the
appliance. When pressed, this
button lights up to indicate the
motor is powered on, and the
other functions can be used.
Always turn the master power
o and unplug the unit when
the machine is not in use.
EXTRACT
PULSE
HIGHLOW
EXTRACT
PULSE
HIGHLOW
EXTRACT
PULSE
HIGHLOW
EXTRACT
PULSE
HIGHLOW
EXTRACT
PULSE
HIGHLOW
THE EXTRACT PROGRAM
Use to break down whole
fruits, vegetables, and ice into
nutrient-rich smoothies. This
button will activate a run cycle
that shuts o automatically.
EXTRACT
PULSE
HIGHLOW
EXTRACT
PULSE
HIGHLOW
EXTRACT
PULSE
HIGHLOW
EXTRACT
PULSE
HIGHLOW
EXTRACT
PULSE
HIGHLOW
WARNING!
NEVER BLEND HOT INGREDIENTS IN ANY SEALED NUTRIBULLET® CUP
Doing so may cause excessive pressure buildup, resulting in risk of personal
injury or property damage. Hot items should only be blended in the pitcher
using proper safeguards.
PULSE
Use to control chopping
and processing.
WARNING: DO NOT use this
setting with hot ingredients!
How to use the blending control panel.
LOW OR HIGH
Select a speed and press once
to turn on. The button will
illuminate. To pause/stop the
unit, press the button a second
time — it will de-illuminate — or
press POWER . While in the
idle-mode, the POWER button
will remain lit. To fully power
down after pausing, press
POWER and unplug the unit.
NOTE: If using the pitcher, speeds
will run until paused/stopped. If using
the NutriBullet® cups, speeds will
automatically shut o after 60 seconds.
THE EXTRACT PROGRAM
Press the EXTRACT button and
the NutriBullet® Select will do
the work for you. This program
automatically stops at the end
of its cycle. To pause or stop the
blender, press EXTRACT again
or POWER .
PULSE
Press and release the PULSE
button to chop ingredients. If
you hold this button down, it will
continue to run until you release it.
EXTRACT
PULSE
HIGHLOW
EXTRACT
PULSE
HIGHLOW
EXTRACT
PULSE
HIGHLOW
EXTRACT
PULSE
HIGHLOW
EXTRACT
PULSE
HIGHLOW
2322
Care & maintenance.
MOTOR BASE:
• To avoid risk of injury, NEVER
attempt to clean the actuator
system on the motor base
while the NutriBullet® Select
is plugged in.
Do not attempt to remove any
pieces from the motor base.
Use a sponge or dish cloth
dampened with warm soapy
water to wipe down the
motor base until clean.
If necessary, you may use
a small brush to scrub the
actuator system area to
ensure it’s clean.
To clean leakage residue
from the motor base, wipe
with a damp sponge and
warm water.
If necessary, you may use
a small brush to scrub the
actuator system area to
ensure it’s clean.
WARNING: Never submerge
the motor base in water.
Here’s how to clean
the NutriBullet®:
STEP 1:
The most important thing —
ALWAYS POWER OFF THE UNIT
and UNPLUG the motor base
from the power outlet when it
is not in use. Do not attempt to
handle the appliance until all
parts have stopped moving!
This includes during assembly
and disassembly, while
changing accessories during
cleaning, and any time you
leave the machine unattended.
STEP 2:
Detach the NutriBullet® cup /
easy-twist extractor blade or
pitcher from the motor base.
STEP 3:
Clean the individual
components (motor base,
easy-twist extractor blade,
NutriBullet® cups, or pitcher) as
recommended in this section.
NUTRIBULLET® CUPS
& TOGO LIDS:
These items are TOP RACK
dishwasher-safe. We
recommend rinsing and briefly
scrubbing them with a dish
brush to remove any remaining
debris before placing in the
dishwasher. NEVER use the
sanitize cycle to wash the cups
— heat this high can warp
the plastic.
NUTRIBULLET® PITCHER:
The pitcher is dishwasher-
safe. We recommend rinsing
and briefly scrubbing it with
a dish brush to remove any
remaining debris before
placing in the dishwasher.
NEVER use the sanitize cycle
to wash the pitcher — heat
this high can warp the plastic.
If preferred, hand-wash the
pitcher with soap and water.
Stuck-on ingredients might
require extra scrubbing from
a dish brush or sponge.
Regularly check the
structure of the pitcher and
twisting threads for cracking,
crazing, or breakage.
If damaged, replace
immediately to prevent
possible personal injury.
EASYTWIST
EXTRACTOR BLADE:
Blades are sharp! Handle
the easy-twist extractor
blade with care when
cleaning! It is best to clean
blades immediately after use
to reduce buildup of residue.
If food particles get stuck,
use a small brush or sponge
to target and dislodge them.
Do not remove any
components of the easy-
twist extractor blade; this
can result in permanent
damage to the blade,
resulting in leakage when
blending. If, over time, the
easy-twist extractor blade
becomes loose or damaged,
you may order a new easy-
twist extractor blade at
nutribullet.com or contact
customer service.
Dry the easy-twist extractor
blade completely after
every use.
Regularly check the
condition of the bottom
of the blade for cracking
or breakage. If damaged,
replace easy-twist extractor
blade immediately to prevent
possible personal injury.
Cleaning the NutriBullet® Select is easy. The pitcher is dishwasher-
safe while the cups and to-go lids are TOP RACK dishwasher-safe.
The easy-twist extractor blade and motor base can be quickly hand-
washed with soap and water. Read on for best practices.
2524
NEVER USE A PITCHER
THAT DOES NOT PROPERLY
ALIGN WITH THE BLADE.
Doing so may cause the
pitcher and motor base to
separate, exposing the
blade assembly and
potentially causing severe
personal injury.
TAMPER
Always hand-wash the
tamper with soap and water.
Stuck-on ingredients might
require extra scrubbing from
a dish brush or sponge.
STUBBORN CLEAN UP:
If ingredients get stuck to the
NutriBullet® cups, easy-twist
extractor blades, or pitcher,
heres an easy cleanup solution:
fill the vessel with room
temperature (21°C/70°F or less)
water to its MAX line and add
1-2 drops of dish soap. For cups,
Replacement parts.
To order additional parts and accessories, please visit our website
at nutribullet.com/shop/accessories or feel free to contact
customer service: 1.800.523.5993.
twist on the easy-twist extractor
blade, and blend on the motor
base for 20-30 seconds. For the
pitcher, attach lid and blend on
the motor base for the same
amount of time, 20-30 seconds.
This should loosen debris
enough to scrub away with
soap and water.
How to store:
Store the NutriBullet® Select
upright with the pitcher lid
secured on top. Do not place
anything on top of the pitcher
lid. Store remaining pieces in a
safe place where they will not be
damaged and won’t cause harm.
WARNING: NEVER store the
easy-twist extractor blade on the
motor base without a NutriBullet®
cup or the pitcher attached as the
exposed blades pose a serious
laceration hazard.
NutriBullet® Select
one-year limited
warranty.
LIMITED WARRANTY
FOR NUTRIBULLET®
NutriBullet's limited warranty
obligations are confined to the
terms set forth below:
NutriBullet, LLC (“NutriBullet”)
warrants this NutriBullet®
against defects in materials
and workmanship for a period
of one year from the date
of original retail purchase.
This limited warranty is valid
only in the country in which
the product is purchased
and comes with the product
at no extra charge, however
shipping and processing fees
will be incurred for returns,
replacements and or refunds.
If a defect exists, and
NutriBullet® is obligated under
this limited warranty, at its
option NutriBullet® will (1) repair
the product at no charge, using
new or refurbished replacement
parts, (2) exchange the product
with a product that is new or
that has been manufactured
from new or serviceable used
parts and is at least functionally
equivalent to the original
product, or (3) refund the
purchase price of the product. A
replacement product assumes
the remaining warranty of the
original product. A repaired
product has a one-year
warranty from the date of
repair. When a product or part
is exchanged, any replacement
item becomes your property
and the replaced item becomes
NutriBullet’s property. When a
refund is given, your product
becomes NutriBullet’s property.
OBTAINING WARRANTY
SERVICE
For limited warranty service,
simply call our customer
service department at 1-800-
523-5993 or contact us via
email from our website at
nutribullet.com, simply click
the contact us link, fill out and
submit the customer contact
form and we will be glad to
help you. When you contact our
customer service department
you will be asked for your
name, address, telephone
number and to provide proof of
2726
the original purchase (receipt)
containing a description of the
product(s), purchase date, and
the appropriate NutriBullet®
serial number(s). Before you
send your product for limited
warranty service please make
sure to keep a copy of all
relevant documents for your
files (receipt, etc.). It is always
recommended to purchase
product insurance and tracking
services when sending your
product for service. Remember,
shipping and processing fees
will be incurred and are not
covered by the one-year
limited warranty.
EXCLUSIONS & LIMITATIONS
This NutriBullet® One-
Year Limited Warranty
applies only to NutriBullet®
products distributed by or
for NutriBullet® that can be
identified by the “NutriBullet”
trademark, trade name, logo
and bar code. NutriBullet®
Select One-Year Limited
Warranty does not apply to
any other products that may
appear to be authentic, but
were not distributed/sold by
NutriBullet, LLC.
Normal wear and tear is not
covered by this limited warranty.
This limited warranty applies
to consumer use only, and
is void when the product
is used in a commercial or
institutional setting.
This limited warranty extends
only to the original consumer
purchaser and is not
transferable. In addition, proof of
purchase must be demonstrated.
Repair or replacement of
the product (or, if repair or
replacement is not feasible, a
refund of the purchase price)
is the exclusive remedy of the
consumer under this limited
warranty. NutriBullet, LLC shall
not be liable for any incidental
or consequential damages for
breach of this limited warranty
or any implied warranty on
this product.
This limited warranty gives
you specific legal rights, and
you may also have other rights
which vary from state to state.
NutriBullet® is not liable for
any damage to products not
covered by this warranty (e.g.,
cups, book, User Guide).
This limited warranty does not
apply: (a) to damage caused
by accident, abuse, misuse,
or misapplication; (b) to
damage caused by improper
maintenance (including
unauthorized parts service);
(c) to a product or a part that
has been modified in any way;
(d) if any NutriBullet® serial
number or trademark has been
removed or defaced; and or (e)
if the product has been used
with an adapter/converter.
THIS LIMITED WARRANTY
AND THE REMEDIES SET
FORTH ABOVE ARE EXCLUSIVE
AND IN LIEU OF ALL OTHER
WARRANTIES, REMEDIES
AND CONDITIONS, WHETHER
ORAL OR WRITTEN, EXPRESS
OR IMPLIED. NUTRIBULLET®
SPECIFICALLY DISCLAIMS ANY
AND ALL IMPLIED WARRANTIES,
INCLUDING, WITHOUT
LIMITATION, WARRANTIES
OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR
PURPOSE. IF NUTRIBULLET
CANNOT LAWFULLY DISCLAIM
IMPLIED WARRANTIES UNDER
THIS LIMITED WARRANTY,
ALL SUCH WARRANTIES,
INCLUDING WARRANTIES
OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR
PURPOSE ARE LIMITED IN
DURATION TO THE DURATION
OF THIS LIMITED WARRANTY.
No NutriBullet® reseller, agent, or
employee is authorized to make
any modification to this warranty.
NUTRIBULLET IS NOT
RESPONSIBLE FOR DIRECT,
SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES
RESULTING FROM ANY
BREACH OF WARRANTY
OR CONDITION, OR UNDER
ANY OTHER LEGAL THEORY,
INCLUDING BUT NOT LIMITED
TO LOST PROFITS, DOWNTIME,
GOODWILL, DAMAGE TO
OR REPLACEMENT OF
EQUIPMENT AND PROPERTY.
NUTRIBULLET® SPECIFICALLY
DOES NOT REPRESENT THAT
IT WILL BE ABLE TO REPAIR
ANY PRODUCT UNDER THIS
LIMITED WARRANTY.
Some states and provinces
do not allow the exclusion
or limitation of incidental
or consequential damages
or exclusions or limitations
on the duration of implied
warranties or conditions,
so the above limitations or
exclusions may not apply to
you. This warranty gives you
specific legal rights, and you
may also have other rights
that vary by state or province.
28
Warranty registration.
How to find serial number
under the motor base.
Please visit nutribullet.com/
warranty-registration or call
1.800.523.5993 to register your
new NutriBullet® Select. You will
be asked to enter the Serial
Number* of your product, along
with the purchase date and
place of purchase.
The registration will enable us
to contact you in the unlikely
event of product safety
notification. By registering
your product you
acknowledge to have read
and understood the
instructions for use, and
warnings set forth in the
accompanying instructions.
1.800.523.5993 | nutribullet.com
NutriBullet, LLC | www.nutribullet.com | All rights reserved.
NutriBullet and the NutriBullet logo are trademarks of CapBran Holdings, LLC
registered in the U.S.A. and worldwide.
The 1000 watt rating of this appliance was obtained by using the 32oz cup with Blade
Holder Assembly and 100g of beef with tendon at max speed for 15 seconds.
Illustrations may dier from the actual product. We are constantly striving
to improve our products, therefore the specifications contained herein
are subject to change without notice.
191025_NB50200
Guide de
l’usager.
®
SELECT
33
INFORMATION
GÉNÉRALE DE
SÉCURITÉ
Une surveillance étroite
est nécessaire lors de
l’utilisation par ou près
des enfants. Tenez le câble
d’alimentation éloigné des
enfants. Cet appareil n’est
pas un jouet. Ne laissez pas
les enfants jouer avec.
NE LAISSEZ JAMAIS LE
NUTRIBULLET® SANS
SURVEILLANCE PENDANT
SON UTILISATION.
NE UTILISER PAS À
L’EXTÉRIEUR.
DÉBRANCHEZ TOUJOURS LE
NUTRIBULLET® S’IL N’EST
PAS UTILISÉ.
SÉCURITÉ DE CHALEUR
ET DE PRESSION
Portez toujours un soi et
une attention extrêmes en
utilisant des ingrédients
chauds dans tout produit de
Précations importantes.
Avertissement! Afin d’éviter tout risque de blessure sérieuse,
veuillez lire attentivement toutes les instructions avant d’utiliser
votre NutriBullet®. Lors de l’utilisation de tout appareil électrique,
les précautions sécuritaires de base doivent toujours être suivies, y
compris l’importante information suivante.
Conservez ces instructions!
POUR USAGE DOMESTIQUE UNIQUEMENT
!
mélange car le frottement des
lames tournantes (au cours
du processus de mélange),
combiné à l’énergie thermique
des ingrédients chaués,
peut générer une situation
dangereuse si elle nest pas
contrôlée adéquatement.
Procédez avec une
prudence accrue en
mélangeant les liquides
chauds dans le pichet.
N’allumez jamais sans
insérer et verrouiller le
bouchon ventilé dans le
couvercle du pichet car
les ingrédients peuvent
éclabousser et, s’ils
sont chauds ou tièdes,
peuvent causer des
dommages thermiques
corporels ou matériels.
3534
nutritives. Le NutriBulle
Select n’est pas conçu pour
utilisation sans liquides ou
comme broyeur à glace.
AJOUTEZ TOUJOURS DU
LIQUIDE à votre recette.
N’UTILISEZ PAS la lame
d’extraction facile à tourner
pour broyer des éléments
secs tels que des grains,
céréales ou café car ceci
pourrait endommager
le moteur ou la lame
d’extraction facile à tourner.
Nous recommandons le
remplacement de votre lame
d’extraction facile à tourner
à tous les 6 mois (selon
l’utilisation) ou au besoin
pour un rendement optimal.
SÉCURITÉ DU PICHET
Assurez-vous que la lame
d’extraction facile à tourner
est fixée solidement à la
base du pichet avant de
mélanger. Omettre d’aligner
adéquatement la lame et
l’attachement du pichet
peut entraîner une fuite de
liquide par la base, amenant
éventuellement la séparation
des composants au cours du
mélange. Ceci peut entraîner
des dommages à la machine,
matériels et corporels.
Dans les recettes qui exigent
que certains ingrédients
soient incorporés au cours
du mélange, ajoutez d’abord
les ingrédients de base,
scellez le couvercle du pichet
De la vapeur et des
ingrédients éclaboussés
peuvent séchapper par le
couvercle du pichet, pouvant
ébouillanter ou brûler
l’utilisateur. Ne mélangez
JAMAIS des liquides chauds
dans votre pichet sans que le
bouchon ventilé soit inséré et
verrouillé dans le couvercle
du pichet et fixé. Le bouchon
ventilé permet à la vapeur et
à la pression de séchapper
tout en préservant des
éclaboussures excessives.
Lors du mélange de
liquides chauds, ajoutez
les ingrédients liquides et
solides sous leur ligne MAX
respective. Fixez le couvercle
du pichet avec le bouchon
ventilé inséré et verrouillé.
Appuyez sur POWER et
commencez à mélanger au
réglage LOW. Une fois les
ingrédients intégrés, vous
pouvez augmenter la vitesse
au besoin.
Si le NutriBullet® mélange
plus d’une minute, le
frottement des lames
peut faire surchauer les
ingrédients et générer une
pression à l’intérieur du
contenant. Si un contenant
de mélange devient chaud
au toucher, éteignez la
machine et laissez le
contenant se refroidir
complètement avant de
l’ouvrir avec soin, pointé en
direction opposée à votre
corps afin d’éviter
toute blessure.
Ne mélangez jamais de
liquides gazéifiés, réactifs
ou eervescents (par ex.
bicarbonate de soude,
poudre à pâte, vinaigre,
acide citrique, levure, etc.).
La pression des gaz dégagés
pourrait créer l’explosion ou
la séparation d’un contenant
de mélange, entraînant
d’éventuels dommages
corporels ou matériels.
SÉCURITÉ DES LAMES
Ne rangez jamais une
lame d’extraction facile
à tourner dans la base
moteur mais non reliée
à un pichet NutriBullet®.
Une lame exposée
pourrait présenter un
risque de lacération.
Les lames sont coupantes!
Maniez toute lame
prudemment. Afin d’éviter
toute lacération, ne
manipulez ou ne touchez
pas le fil de la lame.
ÉVITEZ TOUT CONTACT
AVEC LES PIÈCES MOBILES!
Éloignez vos mains et
vos ustensiles des lames
lorsque vous mélangez de la
nourriture afin de réduire le
risque de blessure grave.
WARNING!
WARNING!WARNING!
WARNING!
AFIN DE RÉDUIRE LE RISQUE
DE DOMMAGES CORPORELS
OU MATÉRIELS, assurez-
vous que la lame d’extraction
facile à tourner est tournée
de manière sécuritaire
(serrée à la main) sur la
tasse NutriBullet® avant de
la placer sur la base moteur
et d’utiliser le NutriBullet®
Select. Assurez-vous que
la lame d’extraction facile
à tourner est bien alignée
avant de la placer sur la
base moteur et d’utiliser le
NutriBullet® Select.
Après avoir mélangé, tournez
l’assemblage contenant
de mélange puissant et
lame d’extraction facile à
tourner de la base moteur
jusqu’à ce que le moteur
s’arrête complètement et
que l’appareil séteigne.
Enlever le contenant du
mélange de l’appareil avant
son arrêt complet pourrait
endommager la bride ou
l’engrenage du moteur de la
lame d’extraction facile
à tourner.
N’utiliser jamais le
NutriBullet® Select sans
ajouter de liquide; cela
pourrait endommager
les lames.
Laction cyclonique® du
NutriBullet® Select nécessite
l’utilisation de liquides
pour faire des smoothies et
autres nombreuses recettes
3736
avec le bouchon ventilé
installé et commencez à
mélanger. Une fois ces
ingrédients bien mélangés,
dévissez le bouchon ventilé
et versez ou déposez avec
précaution les ingrédients
dans le mélange.
Si vous devez pousser des
ingrédients pus près de la
lame, UTILISEZ SEULEMENT
LE POUSSOIR FOURNI
avec le NutriBullet® Select.
N’utilisez PAS d’ustensile
ou appareil autre que le
poussoir pour pousser des
ingrédients vers la lame. Le
poussoir est spécifiquement
conçu pour ne pas entrer
en contact avec la lame.
Les spatules, cuillers et
autres outils peuvent
toucher la lame, ce qui peut
entraîner des dommages
à la machine, matériels et
possiblement corporels.
N’UTILISEZ JAMAIS VOS
DOIGTS OU AUCUNE PARTIE
DE VOTRE MAIN POUR
POUSSER DES INGRÉDIENTS
VES LA LAME. Utilisez
seulement le poussoir fourni.
N’oubliez pas d’exercer
une prudence accrue en
mélangeant des liquides
ou des ingrédients chauds
dans le pichet.
Des éclaboussures ou de la
vapeur échappée peuvent
causer des brûlures ou des
dommages matériels.
Ne remplissez pas le
contenant au-dessus des
lignes de capacité maximales
pour les ingrédients liquides
et solides.
Commencez toujours le
mélange d’ingrédients
chauds sur le réglage LOW.
Éloignez vos mains et votre
peau exposée de l’ouverture
du couvercle pour prévenir
des brûlures éventuelles.
SÉCURITÉ ÉLECTRIQUE
N’utilisez pas ce produit dans
des endroits qui ont des
caractéristiques ou des types
de fiche diérents. N’utilisez
avec aucun type d’adapteur
de fiche ou de convertisseur
de voltage car ceux-ci
peuvent causer des courts-
circuits, incendies, chocs
électriques, dommages
personnels ou au produit.
L’utilisation d’attachements,
tels que des bocaux de
mise en conserve, nest
pas recommandée et peut
causer des incendies, chocs
électriques, dommages
personnels ou au produit et
elle annule la garantie
du produit.
Pour éviter le risque de
choc électrique, ne plongez
jamais le fil, la fiche ou la
base moteur du NutriBullet®
Select dans l’eau ou d’autres
liquides. Cessez l’utilisation
si le fil, la fiche ou la base
moteur est endommagé.
ÉTEIGNEZ toujours
en DÉBRANCHANT le
NutriBullet® Select quand il
n’est pas utilisé ou AVANT
l’assemblage, le démontage,
le changement d’accessoires
et le nettoyage. N’essayez
pas de manipuler le
NutriBullet® Select avant
que toutes les pièces n’aient
cessé de bouger.
Ne laissez pas le fil pendre
en bas du rebord de la
table ou du comptoir. Il
ne faut pas tirer ni tordre
ni endommager le fil
d’alimentation. Ne laissez pas
le fil toucher à des surfaces
chaudes, y compris le poêle.
Si le moteur cesse de
fonctionner, débranchez la
base moteur et laissez-la
refroidir durant au moins 15
minutes avant de l’utiliser
de nouveau. Le NutriBullet®
Select a un disjoncteur
interne qui éteint le moteur
en cas de surchaue. Le
disjoncteur thermique se
réinitialise quand l’appareil
est débranché et le
disjoncteur thermique se
refroidit susamment.
INFORMATION SUR LA
FICHE POLARISÉE :
Cet appareil comporte des
marques sur la fiche. La
fiche d’attachement ou le fil
complet nest pas convenable
au remplacement. En cas de
dommage, l’appareil
est remplacé.
Votre NutriBullet® Select est
doté d’une fiche polarisée (une
branche plus large que l’autre)
afin de réduire le risque de
choc électrique. Cette fiche
s’insère correctement d’une
seule manière dans une
prise polarisée. Si la fiche ne
s’insère pas complètement
dans la prise, retournez-la.
Si elle ne s’insère toujours
pas, contactez un électricien
qualifié.
Pour votre sécurité, ne
modifiez pas la fiche ou
la base moteur d’aucune
manière. Ceci augmente le
risque se blessure et annule
la garantie du produit.
SÉCURITÉ DU CHAUFFAGE
SUR LE DESSUS DU POÊLE
Pour réchauer des éléments
mélangés à la température
de la pièce ou moins (21° C
ou 70° F ou moins), transférez
le mélange dans un
chaudron pour le réchauer.
Utilisez un thermomètre
pour tester la température
interne des ingrédients cuits.
Ils peuvent sembler frais au
toucher mais quand même
être chauds à l’intérieur.
Le NutriBullet® Select nest
pas conçu pour usage sur le
dessus du poêle. Ne placez
pas la base moteur ou tout
autre accessoire NutriBullet®
sur le poêle ou au micro-
ondes ou dans l’eau
bouillante. Vous pourriez
endommager l’accessoire.
WARNING!
WARNING!
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31

NutriBullet NB-50200 Mode d'emploi

Catégorie
Mélangeurs
Taper
Mode d'emploi
Ce manuel convient également à

dans d''autres langues