Legrand IPPAN3-B MCCB Wireless module Guide d'installation
- Taper
- Guide d'installation
IPPAN3-B
Installation Manual
Version 1.0
May 2020
CONTENTS
1.0 OVERVIEW
2.0 IPPAN3-B MODULE
2.1 SPECIFICATIONS
2.2 ANTENNAS
2.3 OPERATING CHANNELS
3.0 MODES OF OPERATION
4.0 INSTALLATION
4.1 DESIGN GUIDELINES
4.2 END USER GUIDELINES
5.0
AGENCY CERTIFICATIONS
6.0
OEM LABELING REQUIREMENTS
7.0
END USER LICENSE AGREEMENT
1.0
OVERVIEW
Thank you for choosing the IPPAN3-B module by Wattstopper. This manual will guide
you through the process of installing the module.
IPPAN3-B embeds wireless IPv6-based communication into each Wattstopper or host
device, and uses wireless mesh networking technology to connect to the internet.
Each
IPPAN3-B module has a unique IPv6 address and “smart” functionality which
enables
wireless data gathering, communication, and control of the host device.
The IPPAN3-B module is designed to be a self-contained IEEE® 802.15.4 and BLE
compliant wireless interface to be employed in conjunction with a variety of daughter
boards that maintain a stable 2.1-3.3Vdc supply. IPPAN3-B provides a diverse set of
I/O options such as serial interface or general purpose I/O. IPPAN3-B is comprised of
a
microcontroller, transceiver, amplifier, and two antennas.
2.0 IPPAN3-B MODULE
FIG 1.0
2.1
SPECIFICATIONS
Specification
IPPAN3-B
Performance
Tuning Range
Internally calibrated for the selected IEEE
channel
Data Rate
250kb/s
Max 802.15.4 Radio Output Power
16.4dBm
Max BLE Radio Output Power
2.0dBm
802.15.4 Receiver Sensitivity
-101dBm
BLE Receiver Sensitivity
-96 dBm
Power Requirements
VCC
2.0 - 3.3Vdc, 0.3A
General
Dimensions
5.7 x 24.3 x 33 mm (H x W x D)
Operating Temperature
-30° C to + 60° C
Humidity
90% RH (max), non-condensing
Agency Approval
United States (FCC, 15.247)
Q4B-P3B
Industry Canada (IC)
21161-P3B
FIG 2.0
FIG 3.0
PIN #
NAME
DESCRIPTION
1
3v3/VCC
Voltage Supply
2
UART-DOUT
Serial UART Out
3
UART-DIN
Serial UART In
4
GPIO_4
High Drive General Purpose Input/Output
5
RESET
Module Inverted Reset
6
EXT_SPI_MISO
SPI Master Input → Slave Output
7
EXT_SPI_CLK
SPI Clock
8
GPIO_0
General Purpose Input/Output
9
EXT_SPI_MOSI
SPI Master Output → Slave Input
10
GND
Ground
11
SPARE(<10kHz)
General Purpose Input/Output (Low Frequency)
12
SPARE(HI f)
General Purpose Input/Output (High Frequency)
13
IN_SCLK
General Purpose Input/Output
14
IN_BUS_MOSI
SPI Master Output → Slave Input
15
IN_BUS_MISO
SPI Master Input → Slave Output
16
SLEEP_AMP/NFC1
Radio sleep control or Near-Field Communication
17
AMP_BYPASS/NFC2
Front End Bypass or Near-Field Communication
18
CTX
General Purpose Input/Output (Low Frequency)
19
GPIO_6
General Purpose Input/Output
20
SWDCLK
SWD Clock
21
SWDIO
SWD Data
22
GPIO_2
General Purpose Input/Output
23
GPIO_5
General Purpose Input/Output
24
EXT_SPI_CS
SPI CS or General Purpose Input/Output
25
I2C_DATA
I2C Data
26
I2C_CLK
I2C Clock
27
GPIO-3
General Purpose Input/Output
28
GPIO_1
General Purpose Input/Output
29
AtoD PWM GPIO
Analog to Digital Converter or Pulse Width Modulation or General Purpose Input/Output
30
AtoD PWM GPIO
Analog to Digital Converter or Pulse Width Modulation or General Purpose Input/Output
31
AtoD PWM GPIO
Analog to Digital Converter or Pulse Width Modulation or General Purpose Input/Output
32
AtoD PWM GPIO
Analog to Digital Converter or Pulse Width Modulation or General Purpose Input/Output
FIG 4.0
2.2
Antennas
The IPPAN3-B module can have two antennas. ANT1 antenna use ceramic antenna ,
the gain less than 0.5dBi, and the ANT2 antenna can use Dipole antenna and other
wire antennas, but the gain can not higher than 2.0dBi.
2.3 Operating Channels
IPPAN3-B provides a wide range of channels.
IEEE 802.15.4 Operating
Channels
Operating Frequency
[GHz]
11
2.405
12
2.410
13
2.415
14
2.420
15
2.425
16
2.430
17
2.435
18
2.440
19
2.445
20
2.450
21
2.455
22
2.460
23
2.465
24
2.470
25
2.475
FIG 5.0
3.0
Modes of Operation
The final use and application of IPPAN3-B is dependent on the firmware pre-installed
at the factory. However, all applications have common modes of operations that can
be summarized as follows for both the IEEE® 802.15.4 and BLE radios:
NOTE: IEEE® 802.15.4 can be used only when BLE is not in use.
Idle Mode
IPPAN3-B enters idle mode of operation whenever the device is not in transmit, or
receive mode, or when there is no data to process.
Data Processing Mode
When an interrupt, timer, frame reception, or frame transmission event occurs
IPPAN3-B moves out of idle mode and into data processing mode. In this mode
IPPAN3-B can processes information and act on data accordingly.
Receive Mode
When a 802.15.4, or BLE, compliant message is received by the transceiver and it’s
either addressed for IPPAN3-B or broadcast the device can be said to be in receive
mode. In receive mode IPPAN3-B validates data and address before accepting the
message for processing.
Transmit Mode
In this mode IPPAN3-B generates an 802.15.4, or BLE, compliant message that can
be sent directly to another IPPAN3-B or broadcast to all other IPPAN3-B modules
within radio range. Transmission mode is preceded by user interaction, a data logging
event, a
network maintenance message or as a response to a message
acknowledgement request.
4.0
INSTALLATION
IPPAN3-B will come pre-programmed from the manufacturer, and in many cases
pre-installed in a device. If you have elected to install IPPAN3-B in house, it is
important to understand how to handle, install, and use properly.
4.1 DESIGN GUIDELINES
● The IPPAN3-B Module is designed either to be surface mounted.
● standard 20 pin footprint using the following sockets:
○ Samtec P/N: MMS-110-01-L-SV
○ Samtec P/N: SMM-110-02-SM-S
● Standard electrostatic discharge precautions should be taken when handling the
module.
● The socket should be designed in a manner where the radiating structures
(antenna) are away from other sensitive electronics
● No antenna modifications can be made (see section 5.0)
● FCC labeling guidelines must be maintained (see section 5.0)
● All stated electrical maximum and minimum values must be met (see section 2.1)
FIG 6.0
4.2
END USER GUIDELINES
The module is designed to be used in fixed locations. If the end user experiences
communication problems it is recommended to move the transceivers closer to one
another or purchase a repeater.
Objects including, but not limited to, steel reinforced walls, metal electrical boxes,
water, and snow may degrade the working distance between transceivers, and should
be avoided. IPPAN3-B is designed to operate in a mesh network, and in most cases
adding nodes can help overcome communication issues.
FCC requires specific text to be placed within user’s manual or operator instruction
guide for the final commercial product. Specific details on this text can be found in
section 5.0.
Operating Requirements and Conditions
This device complies with Part 15, Subpart C, Section 15.247 of the FCC Rules,This
device IPPAN3-B should not collocate with other radio.
Mobile Device RF Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
Caution Statement for Modifications
CAUTION: Any changes or modifications not expressly approved by Wattstopper could
void the user’s authority to operate the equipment.
FCC Notices
IPPAN3-B has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in an installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning IPPAN3-B off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
● Consult the dealer for help.
IC Caution:
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d'en compromettre le fonctionnement.
Exigences et conditions de fonctionnement:
La conception de IPPAN3-B est conforme aux limites d'exposition aux Frequences
Radio
définies par les normes IC et FCC pour les appareils mobiles.
Déclaration d'exposition aux fréquences radio d'appareil mobile
Cet équipement est conforme aux limites d’exposition aux radiations de la IC définies
pour un environnement non contrôlé. Cet équipement doit être installé et utilisé à une
distance minimale de 20 cm entre le radiateur et votre corps.
Déclaration de mise en garde concernant les modifications
ATTENTION: Tous changements ou modifications qui ne sont pas expressément
approuvés par Wattstopper sont susceptibles de révoquer les droits d'utilisation de cet
équipement.
Avis IC
IPPAN3-B a été testé et entre dans la catégorie des appareils numériques de Classe B,
selon la Section 15 de la réglementation de la IC. Ces limites ont été conçues pour
protéger les installations domestiques contre les interférences néfastes. Cet
équipement génère, utilise et émet de l'énergie sous forme de fréquences radio et, en
cas de non-respect des instructions d'installation et d'utilisation, risque de provoquer
des interférences radio. Il n'existe cependant aucune garantie contre ces interférences.
En cas d'interférences radio ou télévisuelles, pouvant être vérifiées en allumant, puis en
éteignant l'équipement, l'utilisateur est invité à essayer de résoudre le problème de
l'une des façons suivantes :
● Eloigner l'équipement du poste de réception ;
● Brancher l'équipement sur une prise appartenant à un circuit différent de celui
du récepteur ;
● Demander de l'aide auprès du revendeur ou d'un technicien radio/TV
6.0
OEM Labeling Requirements
WARNING! The Original Equipment Manufacturer (OEM) must ensure that FCC/IC
labeling requirements are met. This includes a clearly visible label on the outside of the
final product enclosure that displays the contents shown below.
FCC:
Contains FCC ID: Q4B-P3B
IC:
Contains IC: 21161-P3B
Exigences en matière d'étiquetage OEM :
ATTENTION!
Le fabricant d'équipement d'origine (OEM) doit veiller à ce que les
exigences en matière d'étiquetage de la FCC / IC soient respectées. Cela comprend
une étiquette clairement visible sur l'extérieur de l'enceinte du produit final qui affiche
le contenu ci-dessous.
FCC:
Contient FCC ID: Q4B-P3B
IC:
Contient IC: 21161-P3B
7.0
END USER LICENSE AGREEMENT
1.
USER NOTICE
Please read this End User Software License Agreement (“License Agreement”) carefully
before using your Wattstopper product. By installing and registering an Wattstopper
device you hereby agree with the terms of this License Agreement. If you do not agree
with the terms of this License Agreement, do not use the Wattstopper Product and
Wattstopper Software.
2.
TERMS
The terms of this License Agreement are applicable to anyone who uses Wattstopper
Software and Firmware included in a product purchased from Wattstopper and/or
Wattstopper partners. This license does not permit the use of the Wattstopper Software
in any
other product. Wattstopper reserves the right to take legal action against
anyone
else using, selling or distributing the software. By using the Wattstopper
Product and Wattstopper Software, you agree to the terms of this License Agreement.
3.
LICENSE
Wattstopper grants a single, non-sublicensable, non-exclusive, non-transferable
license to use the Wattstopper Software solely as part of products obtained from
Wattstopper and/or any Wattstopper partner for which applicable fees have been paid.
Except for the limited license rights expressly granted in this License Agreement,
Wattstopper reserves all rights in and to the Wattstopper Software and any
modifications or copies thereto.
4.
GENERAL RESTRICTIONS
In exchange for the license, you agree not to: decompile, disassemble, or reverse
engineer the Wattstopper Software; alter, modify or create any derivative works based
on the Wattstopper Software; use, copy, sell, sublicense, lease, rent, loan, assign,
convey or otherwise transfer the Wattstopper Software except as expressly authorized
in writing by Wattstopper ; distribute, disclose, or allow use of the Wattstopper
Software, in any
format, through any timesharing service, service bureau, network or
by any other means; allow any service provider or other third party, with the exception
of Wattstopper authorized resellers, distributors, and their designated employees who
are
acting solely on behalf of and for the benefit of the end user, to use or execute any
software commands that cause the Wattstopper Software to perform functions that
facilitate the maintenance or repair of any product.
5.
DISCLAIMER OF WARRANTIES
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, WATTSTOPPER
PROVIDES THE WATTSTOPPER SOFTWARE “AS IS” AND “AS AVAILABLE” WITH
ALL
FAULTS AND WITHOUT WARRANTY OF ANY KIND. WATTSTOPPER HEREBY
DISCLAIMS WITH RESPECT TO THE WATTSTOPPER SOFTWARE ALL
WARRANTIES AND
CONDITIONS, WHETHER EXPRESS, IMPLIED OR STATUTORY,
INCLUDING BUT
NOT LIMITED TO ANY (IF ANY) WARRANTIES OR CONDITIONS OF
OR RELATED TO:
NON-INFRINGEMENT, MERCHANTABILITY, FITNESS FOR A
PARTICULAR
PURPOSE, LACK OF VIRUS, ACCURACY, OR COMPLETENESS OF
RESPONSE.
6.
TERMINATION
If you breach the license limitations or restrictions in this License Agreement,
Wattstopper may, with immediate effect, terminate the software licenses granted in
this License Agreement without prejudice to any available rights and remedies. Upon
termination or expiration of the license for any reason, you shall immediately return the
Wattstopper Software and any copies to Wattstopper , or, at Wattstopper discretion,
you shall permanently destroy all copies of the Wattstopper Software and any related
materials in your possession or control. Inadvertent copies of the Wattstopper Software
and any related materials remaining in the possession of the End User subsequent to
termination or expiration shall not be implied or construed as Wattstopper consenting
to transfer ownership of the software and any related materials to the End
User.
7.
LIMITATION OF LIABILITY
TO THE EXTENT NOT PROHIBITED BY APPLICABLE LAW, IN NO EVENT SHALL
WATTSTOPPER BE LIABLE FOR ANY CONSEQUENTIAL, INDIRECT, SPECIAL,
EXEMPLARY, OR PUNITIVE DAMAGES WHATSOEVER (INCLUDING BUT NOT
LIMITED TO DAMAGES FOR: LOSS OF PROFITS, LOSS OF CONFIDENTIAL OR
OTHER INFORMATION, BUSINESS INTERRUPTION) ARISING OUT OF OR IN ANY
WAY RELATED TO THE USE OF OR INABILITY TO USE THE WATTSTOPPER
SOFTWARE,
EVEN IF WATTSTOPPER HAS BEEN ADVISED OF THE POSSIBILITY
OF SUCH
DAMAGES.
8.
COMPLIANCE
Wattstopper will have the right to inspect your compliance with these License
Agreement terms.
9.
GOVERNMENT END USERS
The Wattstopper Software is classified as “commercial computer software” and the
Documentation is classified as “commercial software documentation” or “commercial
items.” Any use, modification, reproduction, release, performance, display or
disclosure of the Wattstopper Software or Documentation shall be governed solely by
the terms of this License Agreement and shall be prohibited except to the extent
expressly permitted.
10.
APPLICABLE LAWS
This License Agreement will be governed by and construed in accordance with the
laws of the United States. Severability in the event that any part or parts of this
agreement shall be held illegal or null and void by any court or administrative body of
competent jurisdiction, such determination shall not affect the remaining parts of this
agreement, and they shall remain in full force and effect as if such part or parts
determined illegal or void had not been included.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
Legrand IPPAN3-B MCCB Wireless module Guide d'installation
- Taper
- Guide d'installation
dans d''autres langues
Documents connexes
-
Legrand Wattstopper IPPAN4 Manuel utilisateur
-
wattstopper NWTL-111-1P/2P version 2 BUILT Wireless Control Node Guide d'installation
-
Legrand Integrated Fixture Sensor & Controller Guide d'installation
-
-
-
-
-
-
-
wattstopper FSP-311B-S-L7-G Guide d'installation
