EW‐7489WAX
EW‐7689WTX
QuickInstallationGuide
Product Specification
WirelessTechnology
• IEEE802.11b/g/n/ax2.4GHz1024QAMwith574Mbpps
• IEEE802.11a/n/ac/ax5GHz1024QAMwith 2400Mbps
• SupportMU‐MIMO/OFDMAat2.4GHzand5GHz
• IEEE802.11ax6GHz1024QAMwith
ExternalInterface
• 1xGELAN(PoE802.3atPD)
• 1xConsoleport
• 1x12VDCJack
• 1xresetbutton
• 1xWPS
• 1xconsoleportRJ45
InternalInterface• 1xConsolePortPINconnector(forcore‐boardUARTuse)
LED • 1xtri‐colorLED
PCBDimension • Coreboard:75x84mm/6L
• Mainboard:170x150mm/4L
EnclosureDimension
• 183.3x183.3x32mm(followAcelinkEW‐7679WIChousing
housing)
• Material:PlenumGraded
• Opennewlowerhousingtoolingtoaccomendatebrackets
andKensingtonlock
Powersupply POE802.3atPD
DC12V1.5A(forEW‐7489WAXonly)
OperatingTemperature0~40degreeC
IO port locations
LED definition
Description (For Alpha/Beta/Charlie/Delta) LED
AP is off or reboot started Off
Normal Operation Solid Green
AP is booting & connecting to wireless controller Flashing
Green
Error, no wireless controller found. AP will
reboot (if not yet claimed by a controller). Check
network connection if error persists.
If reset button pressed: AP preparing configuration rese
Solid Red
Configuration reset in progress * Flashing Slow
Red
Firmware update in progress*
Note: Do not disconnect from power Flashing Fast
Red
AP has no connection to the wireless controller Solid Amber
AP is not claimed by wireless controller Flashing
Amber
Safety Instructions
You can operate the access point (AP) safely if you follow the information in these Safety Instructions
and on the appliance.
Do not reach into the appliance. There are dangerous circuits inside the appliance that can cause death
if you touch them.
Damaged appliances must be returned. It is forbidden to open the hardware appliance or to change its
components. Failure to comply with this rule results in the loss of warranty cover from EDIMAX.
Connect the device to a power socket with a fully functional earth conductor. Defective earth
conductor connections do not comply with the requirements for safety and electromagnetic
compatibility. Check the power socket before connecting the hardware appliance.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
Before you switch on the appliance make sure that your mains voltage complies with the supply
voltage of the appliance. The connection data are shown on the name plate.
To disconnect the appliance completely take the power cable from the power socket. Make sure that
the power plug is freely accessible.
Make sure that no one can trip over the power cable and that it cannot be damaged by objects.
Only connect system peripherals complying with the requirements for protective extra-low voltage
according to EN/IEC 62368-1.
Only use parts and accessories validated by EDIMAX. Using non-approved parts and accessories may
affect the functioning of the appliance and your safety.
The appliance produces heat. Ensure that there is sufficient air circulation to remove the heat.
Avoid a permanent high level of air humidity and formation of condensation. Protect the appliance
from humidity and chemicals. Safe use of the appliance is no longer possible if: the chassis is
damaged water penetrated the appliance objects entered the appliance via air opening smoke comes
out of the appliance the power cable is damaged it does not work properly
Immediately turn off the appliance in the event of one of the above problems, remove the power cable
from the power socket and contact your customer service as soon as possible.
We expressly exclude any product liability and warranty claims if the appliance is not operated
according to the instructions in these notes and to the notes attached to the appliance itself.
PoE-Injector Safety Information
Caution: The PoE injector is to be connected only to PoE networks without routing to the outside
plant.
ÌAC Power Cord: The power cord must have regulatory agency approval for the specific country in
which it is used (for example, UL, CSA, VDE, GS, etc.).
The power cord must be a three-conductor type (two current carrying conductors; one ground
conductor terminated on one end by an IEC 60320 appliance coupler (for connection to the PoE-
Injector), and on the other end by a plug containing a ground (earthing) contact).
The power cord must be razed for a minimum of 250 VAC RMS operation, with a minimum rated
current capacity of 5 A (or a minimum wire gauge of 18 AWG (0.75 mm2)).
A PoE-Injector installed in Australia requires power cords with a minimum wire gauge of 16 AWG
(1.0 mm2).
The PoE-Injector "Data In" and "Data & Power Out" ports are shielded RJ45 data sockets. They
cannot be used as Plain Old Telephone Service (POTS) telephone sockets. Connect RJ45 data
connectors only to those sockets.
The AC wall socket-outlet must be near the PoE-Injector and easily accessible. You can remove AC
power from the PoE-Injector by disconnecting the AC power cord from either the wall socket-outlet
or the PoE-Injector appliance coupler.
The PoE-Injector "Data In" and "Data & Power Out" interfaces are qualified as Safety Extra-Low
Voltage (SELV) circuits according to IEC 62368-1. Connect these interfaces only to SELV interfaces
on other equipment.
Warnings
Connect the PoE-Injector only to the IP device with which it was bought. Using the PoE-Injector with
other IP devices can cause damage to the IP device.
Read the installation instructions before connecting the PoE-Injector to its power source.
Follow basic electricity safety measures whenever connecting the PoE-Injector to its power source.
A voltage mismatch can cause equipment damage and may pose a fire hazard. If the voltage indicated on
the label is different from the power outlet voltage, do not connect the PoE-Injector to that power outlet.
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC
Rules.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 40cm
between the radiator & your body.
Note: The country code selection is for non-US model only and is not available to all US model.
Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only.
FCC regulations restrict the operation of this device to indoor use only.
O The operation of this device is prohibited on oil platforms, cars, trains, boats, and
aircraft, except that operation of this device is permitted in large aircraft while
flying above 10,000 feet.
O Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of
or communications with unmanned aircraft systems.
1
Industry Canada statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following
two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired
operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
Caution
a. Operation shall be limited to indoor use only;
Utilisation limitée à l’intérieur seulement;
b. Operation on oil platforms, cars, trains, boats and aircraft shall be prohibited except for on
large aircraft flying above 10,000 ft.
Utilisation interdite à bord de plateformes de forage pétrolier, de voitures, de trains, de
bateaux et d’aéronefs, sauf à bord d’un gros aéronef volant à plus de 10 000 pieds
d’altitude.
Radiation Exposure Statement
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with greater than 23cm between the radiator & your body.
Déclaration d'exposition aux radiations
Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un environnement
non contrôlé. Cet équipement doit être installé et utilisé à plus de 23cm entre le radiateur et votre corps.
2
RED Compliance Statement
Compliance with 2014/53/EU Radio Equipment Directive (RED)
In accordance with Article 10.8(a) and 10.8(b) of the RED, the following table provides information on the frequency
bands used and the maximum RF transmit power of the product for sale in the EU:
Frequency Range (MHz) Max. Transmit Power (dBm)
EIRP
2412 ~ 2472 19.91 dBm
5180 ~ 5240 22.98 dBm
5250 ~ 5320 22.93 dBm
5500 ~ 5700 22.92 dBm
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
AT BE BG HR CY CZ DK
EE FI FR DE EL HU IE
IT LV LT LU MT NL PL
PT RO SK SI ES SE UK(NI)
This device is restricted to indoor use
EU/UK Declarations of Conformity
Hereby, Edimax Technology Co., Ltd. declares that the radio equipment type EW-7689WTX is in
compliance with Directive 2014/53/EU
Hereby, Edimax Technology Co., Ltd. declares that the radio equipment EW-7689WTX is in
compliance with the Radio Equipment Regulations 2017 (S.I. 2017/1206).
3
Declaration of Conformity
We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described
below complies with the requirements of the European Radio Equipment directives.
Equipment: Access Point
Model No.: EW-7489WAX, EW-7689WTX
The following European standards for essential requirements have been followed:
Directives 2014/53/EU
Spectrum : EN 300 328 V2.2.2 (2019-07)
EN 301 893 V2.1.1 (2017-05)
EMC : EN 301 489-1 V2.2.3 (2019-11)
EN 301 489-17 V3.2.4 (2020-09)
EMF : EN 55032:2015+A11:2020 Class B
EN 55035:2017+A11:2020
Safety (LVD) : IEC 62368-1:2014 (2nd Edition) and/or EN 62368-1:2014+A11:2017
Date&PlaceofIssue:31/May/2022,Taipei
Signature:
PrintedName: HunterChen
Title: Director
a company of:
Edimax Technology Co., Ltd.
No. 278, Xinhu 1st Rd., Neihu Dist.,
Taipei City, Taiwan
Edimax Technology Europe B.V.
Fijenhof 2,
5652 AE Eindhoven,
The Netherlands
Date&PlaceofIssue:31/May/2022,Eindhoven
Signature:
PrintedName: DavidHuang
Title: Director
4
Declaration of Conformity
We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described
below complies with the requirements of the United Kingdom Radio Equipment directives.
Equipment: Access Point
Model No.: EW-7489WAX, EW-7689WTX
The following European standards for essential requirements have been followed:
Radio Equipment Regulations 2017 (S.I. 2017/1206)
Spectrum : EN 300 328 V2.2.2 (2019-07)
EN 301 893 V2.1.1 (2017-05)
EMC : EN 301 489-1 V2.2.3 (2019-11)
EN 301 489-17 V3.2.4 (2020-09)
EMF : EN 55032:2015+A11:2020 Class B
EN 55035:2017+A11:2020
Safety (LVD) : IEC 62368-1:2014 (2
nd
Edition) and/or EN 62368-1:2014+A11:2017
Date&PlaceofIssue:31/May/2022,Taipei
Signature:
PrintedName: HunterChen
Title: Director
a company of:
Edimax Technology Co., Ltd.
No. 278, Xinhu 1st Rd., Neihu Dist.,
Taipei City, Taiwan
Edimax Technology Europe B.V.
Fijenhof 2,
5652 AE Eindhoven,
The Netherlands
Date&PlaceofIssue:31/May/2022,Eindhoven
Signature:
PrintedName: DavidHuang
Title: Director
5
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
