Campfire Audio 2AS58-01 Manuel utilisateur

Taper
Manuel utilisateur
Campfire Audio ORBIT
Regulations and Operations Manual
Regulatory Compliance Information
EU / UK Compliance
English
Campfire Audio hereby declares that this wireless device is in compliance with Directive
2014/53/EU and Radio Equipment Regulations 2017. A copy of the Declaration of Conformity
is available at campfireaudio.com/compliance.
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be
used in portable exposure condition without restriction.
FCC ID: 2AS58-01
ISED Statement
English
This device complies with Industry Canada licenseexempt RSS standard(s). Operation is
subject to the following two conditions: (1) This device may not cause interference, and (2) This
device must accept any interference, including interference that may cause undesired operation
of the device. The digital apparatus complies with Canadian CAN ICES3 (B)/NMB3(B).
This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102
and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF
exposure and compliance.
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled
environment.
RF Exposure Statement
The device has been evaluated to meet general RF exposure requirement. The device can be
used installed and operated with minimum distance 0mm between the radiator and your body.
French: Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitationestautorisée aux deux conditions suivantes: (1)
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareildoit accepter tout
brouillageradioélectriquesubi, mêmesi le brouillageest susceptible d'encompromettre le
fonctionnement. L'appareil numérique est conforme à CAN CAN ICES-3 (B) / NMB-3 (B).
cet appareil est conforme à l'exemption des limites d'évaluation courante dans la section 2.5 du
cnr - 102 et conformité avec rss 102 de l'exposition aux rf, les utilisateurs peuvent obtenir des
données canadiennes sur l'exposition aux champs rf et la conformité.
Cet équipement est conforme aux limites d'exposition aux rayonnements du Canada établies
pour un environnement non contrôlé.
L'appareil a été évalué pour répondre aux exigences générales d'exposition aux RF.Cet
équipement doit être installé et utilisé avec une distance minimale de 0 mm entre le radiateur et
votre corps.
IC24976-01
Operations: Orbit UI
Function
Operation
Use Function Results
1
First-time
Bluetooth Pairing
Put the left and right earphones into the
charging box to charge, open the cap of the
charging box, and press and hold the reset
button for 3 seconds to enter the Bluetooth
pairing mode. Then open phone settings >
Bluetooth devices > refresh devices and
select “CAMPFIRE”
Left and right earphone
lights flash alternately,
indicator lights will go out
after successful pairing.
Pairing mode: all 4 LEDs
will flash 3 times
simultaneously.
2
ON
1. Open the upper cover of the charging box
and auto turn on the device and enter the
automatic connection.
2. Press and hold the left and right earphones
for 5 sec to shut down w/ earphones outside
of charging box
Power on prompt tone:
“ON”
3
OFF
1. Place earphones into charging box and
close cap to automatically turn off
2. Long press the left and right earphones for
5s to shut down
3. Earphones will auto shut down after 10m
without pairing
4. Earphones will turn off from low battery
Power off prompt tone:
“OFF”
4
Rest
Long press the charging box for 10s
5
Auto re-connect
1. Open the charging box cover
2. Earphones will connect to last connected
device
6
Long-distance
connection and
automatic return
connection
After disconnecting beyond the use distance
range, the headset will auto-reconnect when
back within range unless 10m has passed
and earphones have turned off.
7
Bluetooth
Disconnected
1. Auto disconnect when out of range
2. Manual disconnect/turn-off
3. Mobile phone is disconnected or has
Bluetooth turned off
8
Play and Pause
Music
In the playback state, tap once on either
earphone to play or pause music.
9
Previous song
Double-tap the left earphone
10
Next song
Double-tap the right earphone
11
Volume +
Long press the Right earphone, hold to
continuously increase volume
12
Volume -
Long press the Left earphone, hold to
continuously increase volume
13
Voice Assistant
activation
Triple tap Left or Right earphone to wake up
voice assistant (siri)
14
Answer Call
Single-tap either earphone during incoming
call
15
Hang up
During call, single-tap either earphonel
16
Reject the call
Double-tap either earphone during incoming
call
17
DUT mode
When the left and right earphones are paired
double-tap the MFB button
18
Charging box
battery indicator
Open the cover of the charging box or click
the button of the charging box to display
battery level
One light - 25%
Two light - 50%
Three light - 75%
Four light - 100%
19
IPhone battery
display
Earphone battery level and bluetooth
connection will be displayed on Iphone
20
IPhone Volume
sync
Volume of the earphones are synchronized
with the volume of the mobile phone
21
Charging box
battery indicator
Open cover of charging box and press button
to display the battery level of the charging box
22
Earphone charging
Place earphones in charging box and close
cover. Device will disconnect after 3 seconds.
One earphone can be placed in the charging
box without affecting the use of the single
earphone.
23
Bluetooth pairing
Long press the charging box for 3s
Indicator lights will flash in
marquee pattern
24
reset
Long press the charging box for 10s to restore
factory settings
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Campfire Audio 2AS58-01 Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues