AJA Hi5-12G Manuel utilisateur

Marque: AJA

Modèle: Hi5-12G

Catégorie: Convertisseurs vidéo

Taper: Manuel utilisateur

Hi5-12G Mini-Converter

12G SDI to HDMI

Version 1.2r1

Published December 5, 2019

Installation and Operation Guide

Hi5-12G Mini-Converter v1.2r1 2 www.aja.com

Notices

Trademarks

AJA® and Because it matters.® are registered trademarks of AJA Video Systems, Inc.

for use with most AJA products. AJA™ is a trademark of AJA Video Systems, Inc. for

use with recorder, router, software and camera products. Because it matters.™ is a

trademark of AJA Video Systems, Inc. for use with camera products.

CION®, Corvid Ultra®, lo®, Ki Pro®, KONA®, KUMO®, ROI® and T-Tap® are registered

trademarks of AJA Video Systems, Inc.

AJA Control Room™, KiStor™, Science of the Beautiful™, TruScale™, TruZoom™,

V2Analog™ and V2Digital™ are trademarks of AJA Video Systems, Inc.

All other trademarks are the property of their respective owners.

this manual is subject to change without notice. No part of the document may be

reproduced or transmitted in any form, or by any means, electronic or mechanical,

including photocopying or recording, without the express written permission of AJA

Video Systems, Inc.

Contacting AJA Support

When calling for support, have all information at hand prior to calling. To contact AJA

for sales or support, use any of the following methods:

Telephone +1.530.271.3190

FAX +1.530.271.3140

Web

https://www.aja.com

Support Email

suppor[email protected]

Sales Email

[email protected]

Hi5-12G Mini-Converter v1.2r1 3 www.aja.com

Contents

Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Contacting AJA Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Chapter 1 – Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Default Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

AJA Mini-Cong Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

I/O Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Chapter 2 – Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

USB Control and Setup—Using AJA Mini-Cong . . . . . . . . . . . . . . . . . . . 8

Acquiring AJA Mini-Cong . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Installing AJA Mini-Cong . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Running AJA Mini-Cong. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Operating AJA Mini-Cong . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Tabbed Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Input Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Output Tab Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

HDR Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Audio Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Update Tab Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Software Update Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Info Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Appendix A – Specications . . . . . . . . . . . . . . . . . . . . . . . . 21

Hi5-12G Tech Specs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Hi5-12G-R Tech Specs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Hi5-12G-TR Tech Specs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Appendix B – Safety and Compliance . . . . . . . . . . . . . . . . . .27

Warranty and Liability Information . . . . . . . . . . . . . . . . . . . .36

Limited Warranty on Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Limitation of Liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Governing Law and Language; Your Rights. . . . . . . . . . . . . . . . . . . . . . 36

Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Hi5-12G Mini-Converter v1.2r1 4 www.aja.com

Chapter 1 – Introduction

Overview

The Hi5-12G converts 12G-SDI to HDMI 2.0, providing an easy to deploy solution

for monitoring professional 4K/UltraHD SDI signals with 4K/UltraHD HDMI 2.0

displays. The Hi5-12G supports a wide range of input video formats and frame

rates with extremely low latency signal conversion and pristine image fidelity.

It features a 12G-SDI single link input with a reclocked SDI loop out for signal

extension to downstream SDI devices.

Two additional Hi5-12G models support fiber connectivity. The Hi5-12G-R includes

an optical input, and the Hi5-12G-TR includes an optical input and reclocked

optical loop output. These models are perfect for applications where distance is a

factor.

The Hi5-12G is a powerful tool for HDR workflows that require local HDR

Infoframe generation to correctly configure a HDR monitor. The free Mini-Config

application program provides an easy to use GUI interface to configure the

Hi5-12G and to display input signal status information.

Default Operation

When you power up the Hi5-12G with its default settings, it will operate with its

default settings, which includes many automatic settings.

The Hi5-12G's Auto-Configure feature automatically identifies the incoming

SDI signal format and converts the signal based on the HDMI output default

configuration parameters.

AJA Mini-Config Control

AJA’s Mini-Config application is available for firmware updates and advanced

configuration. The Mini-Config application provides configuration controls for

Hi5-12G along with real-time input signal status.

With the Mini Config application, you can specify what input signal parameters

you want to use, specify the output signal format, configure HDR settings, audio

settings, and perform software updates.

Hi5-12G Mini-Converter v1.2r1 5 www.aja.com

Configuration settings made through AJA Mini-Config are stored in the Hi5-12G

unit through subsequent power cycles.

Features

• Convert 12G-SDI to HDMI v2.0b at up to 4K 60p

• Support for 4:4:4/4:2:2/4:2:0 HDMI v2.0b output

• Support for YCbCr and RGB

• HDR support for HDR10 and HLG

• Embedded audio support

• 12G-SDI loop out

• Fiber SFP models available

• Congure via USB port and supplied Mini-Cong software

• Uses 5-16 VDC power (DWP-U-R1 universal power supply included)

• Five year warranty

Block Diagram

Figure 1. Hi5-12G Converter, Simplified Block Diagram

Video

Audio

Embed

Audio

Analog

Audio Out 1

(RCA)

Analog

Audio Out 2

(RCA)

USB Port

(connect to

PC or Mac)

MiniCong Control

D/A

Converter

Optional SFP

Input with

Embedded Audio

HDMI v2.0

Output with

Embedded

Audio

Adjustable

Delay

Video

Processing

SDI Input with

Embedded Audio

SDI Loop

Output

SDI

RCVR

SDI

RCVR

HDMI

XMIT

Optional SFP

Loop Output

Disembed

Audio

Hi5-12G Mini-Converter v1.2r1 6 www.aja.com

I/O Connections

Figure 2. Hi5-12G Converter Connections

HDMI

Output

Connector

USB

Port

DC Power

Input

SDI Input

SFP Cage

Analog

Audio

Outputs

Power LED

Lock LED

SDI Loop

Output

NOTE: The LED adjacent to the SDI connector indicates by color the detected SDI input

signal. Off is no signal, green is SD-SDI, red is HD-SDI, amber is 3G-SDI, magenta is

6G-SDI, and blue is 12G-SDI.

Installation

NOTE: AJA does not support third-party SFP modules. Use of a non-AJA SFP module will

void the warranty.

Hi5-12G-R ships with a 12G-SDI Fiber LC single channel SFP receiver.

Hi5-12G-TR ships with a 12G-SDI Fiber LC channel SFP transceiver.

Installation consists of the following steps:

1. Ensure the Hi5-12G is disconnected from power.

2. Connect video equipment to the converter BNCs.

3. If applicable, connect ber to the 12G-SDI Fiber LC single channel SFP

receiver or transceiver.

CLASS 1

LASER

PRODUCT

Warning! Active ber-optic cables emit radiation invisible to the human eye. Do

not look directly at the end of an active ber-optic cable or the ber connector

on a

Hi5-12G-R or Hi5-12G-TR; these models are Class 1 Laser Products.

Hi5-12G Mini-Converter v1.2r1 7 www.aja.com

Figure 3. Hi5-12G to Fiber LC Single Channel SFP Example

NOTE: Fiber optic interconnections can be severely compromised by dirt, oils, or other

contaminants. All dust caps should be replaced on cables and equipment

whenever Hi5-12G converters are disconnected from fiber optic cables.

4. Apply +5VDC power to the converter (AJA power supply included).

5. The Hi5-12G will now run using the default factory settings. If you wish to

alter the factory settings, you’ll need to:

• Install the AJA Mini-Cong software on your computer

• Attach the Hi5-12G via USB

• Make your changes using AJA Mini-Cong setup screens.

This process is detailed in "USB Control and Setup—Using AJA Mini-Config" on page

NOTE: For highest reliability, the mini converter relies on convection cooling instead

of using a built-in fan. Therefore, when installing the unit, mount in a location

where it has access to air for proper cooling. Do not stack the Hi5-12G with other

mini converters.

Hi5-12G Mini-Converter v1.2r1 8 www.aja.com

Chapter 2 – Operation

USB Control and Setup—Using AJA Mini-Config

Your AJA Mini-Converter can be used right out of the box for some applications

since it is designed to recognize inputs and perform standard actions

automatically by default. However, to use its full capability, you must use AJA’s

Mini-Config software application for PCs and Macs. This same application can be

used to update to new Mini-Converter software released by AJA.

Acquiring AJA Mini-Config

AJA’s Mini-Config application is available for download from the AJA website.

To download the latest AJA Mini-Config package, which includes the AJA Mini-

Config application, Mini-Converter firmware, and documentation, go to:

https://www.aja.com/products/mini-config-software

Select either the Windows or Mac icon to download the desired version.

Mini-Converter Documentation

Included with the AJA Mini-Config package is a complete set of documentation

for all Mini-Converters supported by AJA Mini-Config. A .PDF of the Installation

and Operation Guide for the currently connected Mini-Converter can be accessed

from the AJA Mini-Config UI via the Help/Manual drop-down menu.

Documentation for all AJA Mini-Converters that use AJA Mini-Config can also

be accessed directly in the AJA Mini-Config download package Documentation

folder, and via the Documentation icon available on the Mac installer.

Documentation (and firmware) included with the AJA Mini-Config application

are the versions available at the time of distribution. However, Mini-Converter

software, firmware and documentation are updated regularly, so newer versions

may exist.

To download the latest documentation for an individual Mini-Converter, go to:

https://www.aja.com/family/mini-converters

and navigate to the Support webpage of that Mini-Converter.

Installing AJA Mini-Config

PC Installation

To install AJA Mini-Config on a Windows PC:

1. Download the application from the AJA website (select the Windows icon

on the AJA Mini-Cong Support webpage).

2. Open the AJA_MiniCong.zip le

3. Double-click on the MiniInstaller.msi le.

4. A Setup Wizard will guide you through the installation.

Hi5-12G Mini-Converter v1.2r1 9 www.aja.com

Figure 4. AJA Mini-Config PC Setup Wizard

5. Click Next to begin. Answer the questions in the subsequent dialogues.

When nished, an AJA Mini-Cong shortcut will be installed on the desktop,

and you will be able to locate the AJA Mini-Cong application in the AJA

folder in the Programs listing.

NOTE: If the AJA Mini-Config application already exists on the PC, a different Setup

Wizard appears.

Figure 5. AJA Mini-Config Setup Wizard, Reinstallation

With this screen you can Repair (reinstall) or Remove (uninstall) AJA Mini-Config

on the PC.

Mac Installation

To install the application on a Mac:

NOTE: Macintosh computers must be Intel-based (G5, G4 and earlier models will not

work with AJA Mini-Config).

1. Download the application from the AJA website (select the Apple icon on

the AJA Mini-Cong Support webpage).

2. Open the AJA_MiniCong folder.

3. Double-click on the AJAMiniCong.dmg le.

Hi5-12G Mini-Converter v1.2r1 10 www.aja.com

4. Answer the prompt and a utility program will be launched.

Figure 6. AJA Mini-Config Mac Installer

5. To complete the installation drag the “MiniCong.app” icon to the

Applications folder.

Running AJA Mini-Config

Connect the Mini-Converter to the PC or Mac via the supplied USB cable. Connect

the external power supply (supplied) to the Mini-Converter.

PC Startup

To run AJA Mini-Config on a PC, double-click on the AJA Mini-Config icon on your

desktop, or open the AJA folder in the program list and click on the AJA Mini-

Config application located inside the AJA Mini-Config folder.

Mac Startup

To run AJA Mini-Config on a Mac, open the Applications folder and locate the AJA

Mini-Config application. Double-click the application to launch it.

Saving Setups

A File drop down menu on the AJA Mini-Config application bar allows you to

save the current state of the Mini-Converter to a preset file for later recall.

Hi5-12G Mini-Converter v1.2r1 11 www.aja.com

Using this feature you can set up the converter for different applications, storing

each configuration (Save Preset As...) with a unique name for easy recall (Open

Preset...).

A Revert to Factory Settings menu item similarly allows you to change the

settings back to AJA’s factory defaults.

Operating AJA Mini-Config

The AJA Mini-Config application provides a graphic interface for viewing settings

and updating software. It consists of an information area at the top that shows

the available Mini-Converters attached to the computer via USB, with a graphical

rendering of the selected Mini-Converter showing all the connectors and their

current state.

Colored text next to the connectors indicates the signal type and what the Mini-

Converter is doing:

• Blue text indicates the values automatically selected

• Black text indicates values that you have manually selected

• Red text indicates the Mini-Converter is not detecting a signal, or cannot

operate with the current user settings.

NOTE: Even if no output device is detected, the SDI connector text still shows the signal it

is outputting.

NOTE: Configuration settings in red will change based on the attached output device as

well as input signals. For improved accuracy and reliability, you should configure

the Mini-Converter only when the target output device is attached and input

signals are supplied at the inputs.

Screens are virtually the same on both PC and Mac, with subtle differences that

reflect the general look of the platform environment.

Hi5-12G Mini-Converter v1.2r1 12 www.aja.com

Figure 7. Example AJA Mini-Config Screen

Select a USB port and an

attached Mini-Converter

(name in parentheses)

Each connector is

labeled with the signals

currently detected or

manually selected.

Firmware version

Serial Number

Tabbed screens

Message

Showing

Status

NOTE: The LEDs adjacent to each SDI or Fiber connector indicate by color the detected

SDI input signal. Off is no signal, [Green is SD-SDI], [red is HD-SDI], [amber is

3G-SDI], purple is 6G-SDI, [blue is 12G-SDI].

Selecting a Mini-Converter with the pulldown menu causes this application to

connect to the selected converter. The graphic of Mini-Converter and text below

it provides:

• Type of converter

• Firmware version

• Serial number of the unit.

A status field at the bottom of the screen shows if your application is connected

and communicating with the Mini-Converter.

When configuring the Mini-Converter, select it from the top pulldown, view the

current settings and change any values. Making a change communicates that

new value to the Mini-Converter’s non-volatile memory.

Tabbed Screens

The Tabs delineate control screens with groups of controls for each type of task to

be performed. The controls for the actual configuration parameters are specific

to each Mini-Converter type. When you Click on any of the tab buttons, the pane

below the tabs will change to match your tab selection. Any changes you make

are immediately applied and will be saved, overwriting previous settings.

Hi5-12G Mini-Converter v1.2r1 13 www.aja.com

Input Tab Screen

Click on the Input tab to view and make changes to the converter’s input settings.

Video Source

Selects the input video source. Choose from the following:

• Auto Switch Over - automatically selects between the SDI Input and the

Optical Input (applicable to the Hi5-12G-R and Hi5-12G-TR models).

• SDI Input - selects the SDI input.

• Optical Input - selects the optical input (applicable to the Hi5-12G-R and

Hi5-12G-TR models).

Color Space

Selects the Input Video Color Space. Choose from the following:

• Auto - automatically selects color space based on the input video parameters

and payload ID.

• 4:2:2 YCbCr

• 4:4:4 RGB

• 4:4:4 YCbCr

RGB Range

Selects the Input Video Color Range when the input is RGB. Does not apply when

the input is YCbCr. Choose SMPTE or Full color range.

Bit Depth

Selects the input video bit depth. Choose Auto, 8-bit or 10-bit. Choosing “Auto”

automatically selects the bit depth based on the input video parameters and the

payload ID.

Hi5-12G Mini-Converter v1.2r1 14 www.aja.com

Switch Over Priority

Selects which input (SDI or Optical) is the preferred input. This selection is valid

only when an AJA optical SFP is installed. If and when the selected input signal is

no longer detected, the auto switchover circuit will fail over to the non-priority

input if present.

Choose from Last Valid Input, SDI Input, or Optical Input.

3G-B Mode

Selects the 3G level B Video Mode. Choose from the following:

• Auto - automatically selects the format based on the input video parameters.

• Level B-DL

• B-DS Link 1 - use Link 1

• B-DS Link 2 - use Link 2

Output Tab Screen

Click on the Output tab to view and make changes to the Hi5-12G Output

settings.

Color Space

Selects the Output Video Color Space. Note that DVI output is limited to 4:4:4

RGB. Choose from the following:

• Auto - selects the video format based on the input video and the attached

device’s capabilities.

• 4:2:2 YCbCr

• 4:4:4 RGB

• 4:4:4 YCbCr

• 4:2:0 YCbCr

Hi5-12G Mini-Converter v1.2r1 15 www.aja.com

Bit Depth

Choose from Auto, 8-bit, or 10-bit. Choosing “Auto” automatically selects the

bit depth based on the input video and the attached device’s capabilities. High

frame rate (HFR) 4K/UltraHD 4:4:4 limited to 8 bits. DVI output is limited to 8 bits.

RGB Range

Selects the Output Video Color Range when the output is RGB. Does not apply

when the output is YCbCr. Choose Auto, SMPTE or Full color range. DVI output is

limited to RGB.

Colorimetry

The setting selected in the Colorimetry control determines the colorimetry

value that is transmitted in the AVI Info frame. This information is sent to the sink

regardless of whether the HDR Enable is On or Off.

Choose from the following:

• Auto

• No Data

• Rec.601

• Rec.709

• BT.2020 Non-CL (non-constant luminance)

• BT.2020 CL (constant luminance)

4K/2K Crop

Choose Auto, Off, or On. Provides the option of center cutting 2048x1080

video signals to make 1920x1080, or center cutting 4096x2160 signals to make

3840x2160.

HDMI/DVI

Choose Auto, HDMI, or DVI. When DVI is selected, any audio signals present are

not passed. Choosing “Auto” automatically selects the output mode based on the

attached device’s capabilities.

When the incoming signal is 4K or UltraHD and the HDMI/DVI control is set to

"DVI," the output will be downsampled to deliver a 2048x1080 or 1920x1080

image. The downsampling is accomplished by passing only one of the 2SI

quadrants from the SDI input signal. The output will appear to be a full picture,

but is actually only one quarter of the total pixels. This feature is very helpful

when connecting to a non-4K/UHD preview monitor.

Hi5-12G Mini-Converter v1.2r1 16 www.aja.com

HDR Tab Screen

Click on the HDR tab to view and make changes to the Hi5-12G High Dynamic

Range static metadata extensions settings.

The HDR tab provides a mechanism to inform an HDMI sink device (such as a TV

or monitor) that the video content is HDR encoded. This includes generation of

the Dynamic Range and Mastering Infoframe and the static metadata descriptors

as defined in CTA-861.3 and HDMI v2.0b. This tab includes pre-canned primaries

values for BT.2020 and DCI P3 color gamuts. The Apply Setting button will transfer

all settings to the HDMI transmitter.

NOTE: The Hi5-12G HDR function does not modify the video data.

NOTE: Hover the cursor over each parameter field to view its corresponding description

in a pop-up window.

HDR Enable

Choose Off or On to determine whether HDR metadata is generated.

• O - HDR metadata is not generated, although colorimetry is still getting

signaled downstream.

• On - HDR metadata is generated.

EOTF

Electro-Optical Transfer Function (EOTF) sets the transfer function serving to

convert between non-linear data space and linear light space.

Choose from the following:

• Trad Gamma SDR

• Trad Gamma HDR

• ST 2084 – PQ

• Hybrid Log-Gamma

• Reserved [4], not yet dened

• Reserved [5], not yet dened

Hi5-12G Mini-Converter v1.2r1 17 www.aja.com

• Reserved [6], not yet dened

• Reserved [7], not yet dened

Gamut

Gamut defines locations for the three vertices of the color primaries, as well as the

white point within the x-y plane of the CIE 1931 color space and SMPTE ST 2086

color volume (in the case of HDR).

Choose from the following:

• DCI-P3 D65 (preset values per DCI-P3 Cinema)

• BT.2020 (preset values per ITU BT.2020)

• BT.709 (preset values per ITU BT.709)

• Custom (allows for dening specic custom coordinates)

Display Mastering Luminance

Represents the minimum and maximum Display Mastering Luminance.

• Minimum: Denes the oor of the SMPTE ST 2086 color volume (in the case of

HDR) and is determined by the mastering environment.

• Range: 0.00000 cd/m

to 1.00000 cd/m

• Step size: 0.00002 cd/m

• Maximum: Denes the ceiling of the SMPTE ST 2086 color volume (in the case

of HDR) and is determined by the mastering environment.

• Range: 1 cd/m

to 65535 cd/m

• Step size: 1 cd/m

Maximum Content Light Level (CLL)

Represents the highest-value pixel component in an entire scene. It is

determined by analyzing each frame of video, and can be determined in the post

environment.

• Range: 1 cd/m

to 65535 cd/m

• Step size: 1 cd/m

Maximum Frame Average Light Level (FALL)

Represents the maximum of frame-based average light levels taken over an entire

scene, and can be determined in the post environment.

• Range: 1 cd/m

to 65535 cd/m

• Step size: 1 cd/m

Hi5-12G Mini-Converter v1.2r1 18 www.aja.com

Audio Tab Screen

Click on the Audio tab to view and make changes to the Hi5-12G audio settings.

NOTE: When using the DVI video protocol, no audio is output since that protocol is video

only.

HDMI Source

Choose which SDI embedded audio channels are routed to the HDMI output.

Eight channels are routed at a time. You can choose Ch 1-8 or Ch 9-16. The source

of the audio channels is the currently selected video input.

HDMI Channel Count

Choose Auto, 2 Channels, or 8 Channels for embedded audio. Choosing “Auto”

automatically selects the audio channels based on the attached device’s

capabilities.

Analog Audio Source

Selects the channel pair that will be output to the Analog RCA connectors (L/R)

and the HDMI audio output (when Output Channel Count is in 2-channel mode).

Choose from the following:

SDI Ch 1+2

SDI Ch 3+4

SDI Ch 5+6

SDI Ch 7+8

SDI Ch 9+10

SDI Ch 11+12

SDI Ch 13+14

SDI Ch 15+16

Hi5-12G Mini-Converter v1.2r1 19 www.aja.com

Audio Offset In Frames

Permits delaying the embedded audio in relationship to the video (for example,

to correct for lip sync problems), in 1/16 of a frame increments. Range is from 0

video frames to +7.0 video frames of delay. The actual time duration of delay will

vary depending on the frame rate of the format being converted.

Update Tab Screen

Use this Update screen to view the software version currently installed on the

converter or install new software.

NOTE: When discussing Mini-Converters, “Firmware” is software that will be stored in

the Mini-Converter’s non-volatile memory and used when it is powered up. This is

something different than the AJA Mini-Config application software. The version

numbers shown in the Update screen refer only to the firmware.

Installed - This field shows the version of the firmware currently installed inside

the Mini-Converter.

Desired - This field shows the version of firmware embedded in the AJA Mini-

Config application which you can install into the Mini-Converter by clicking

the Update button.

Update - This button initiates a software update operation loading the “Desired”

version of firmware into the Mini-Converter’s non-volatile memory.

Progress - This indicator bar shows the progress of firmware installation.

Software Update Procedure

1. Check the AJA website for new AJA Mini-Cong software for your Mini-

Converter. If new software is found, download it and uncompress the le

archive (zip). Here is the URL to use when checking:

https://www.aja.com/products/mini-config-software

2. Connect the Mini-Converter to a Mac or PC via a USB port on the computer

and run the new AJA Mini-Cong software just downloaded.

Hi5-12G Mini-Converter v1.2r1 20 www.aja.com

3. Click on the Update tab screen.

4. Check the Installed version level against the Desired version level. If the

Desired is newer, then click the Update button to download the new

rmware to the Mini-Converter; progress will be shown via the “Progress”

thermometer bar.

Info Tab Screen

This screen provides basic information about the Mini-Converter. This information

is useful when calling AJA Support for service or technical support.

Name

This field allows you to give your Mini-Converter a name. This can be useful if you

have several Mini-Converters attached to a Mac/PC via USB so you can distinguish

between them easily (especially if they’re the same model).

Type - This is the factory set model name of the Mini-Converter.

Assembly - This is the factory assembly number.

Serial Number - This is the factory set unique serial number of your Mini-

Converter. If you ever call AJA Support for service, you may be asked for this

number.

La page charge ...

AJA Hi5-12G Manuel utilisateur

Marque: AJA

Modèle: Hi5-12G

Catégorie: Convertisseurs vidéo

Taper: Manuel utilisateur

Télécharger le PDF

rapport

AJA Hi5-12G Manuel utilisateur

AJA Hi5-12G Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents