Frigidaire FRSS2323AW Manuel utilisateur

Catégorie
Frigos
Taper
Manuel utilisateur
Frigidaire.com USA 1-800-374-4432 Frigidaire.ca Canada 1-800-265-8352
use
&
care
REFRIGERATOR
A19894504 (June 2020)
Introduction .......................................................2
Important Safety information.....................3
Features ............................................................5
Installation .........................................................6
Door Removal ..................................................9
Door Handle Installation .............................. 11
Water Supply Connection .......................... 12
Controls and Settings .................................14
Automatic Ice and Water Dispenser ...... 18
Storage Features ..........................................20
Normal Operating Sounds ......................... 21
Filter Replacement ...................................... 22
Care and Cleaning .......................................24
Troubleshooting .......................................... 26
Limited Warranty .........................................30
2
INTRODUCTION
Doors
Handles are secure and tight
Door seals completely to cabinet on
all sides
Doors are level with each other.
Leveling
Appliance is level side-to-side and
tilted ¼" (6 mm) front-to-back
Toe grille is properly attached.
Cabinet is level on the floor.
Electrical Power
House power turned on
Appliance is plugged in
Ice Maker
House water supply connected
to appliance
No water leaks present at all
connections - recheck in 24 hours
Ice maker is turned ON
Ice & water dispenser operates
correctly
Final Checks
Shipping material removed
Refrigerator and freezer tempera-
tures set to recommended setting
Crisper humidity controls set
(some models)
Registration card sent in
Installation Checklist
Welcome to our
family
Thank you for bringing Frigidaire into
your home! We see your purchase as the
beginning of a long relationship together.
This manual is your resource for the use
and care of your product. Please read
it before using your appliance. Keep it
handy for quick reference. If something
doesn’t seem right, the troubleshooting
section will help you with common issues.
FAQs, helpful tips and videos, cleaning
products, and kitchen and home accessories
are available at Frigidaire.com.
We are here for you! Visit our website,
chat with an agent, or call us if you need
help. We may be able to help you avoid
a service visit. If you do need service, we
can get that started for you.
Let’s make it ocial! Be sure to register
your product.
Keep your product info here so it’s easy
to find.
Model Number ____________________
Serial Number ____________________
Purchase Date ____________________
FPO
Serial location
Serial Number Location
Lorem ipsum Lorem ipsumLorem i
psumLorem ipsumLorem ipsumLore
m ipsumLorem ipsum
Lorem ipsum Lorem ipsumLorem i
psumLorem ipsumLorem ipsumLore
m ipsumLorem ipsum
Lorem ipsum Lorem ipsumLorem
3
WARNING
WARNING indicates a potentially haz-
ardous situation which, if not avoided,
could result in death or serious injury.
IMPORTANT
IMPORTANT indicates installation, oper-
ation or maintenance information which
is important but not hazard-related.
DANGER
DANGER indicates an imminently haz-
ardous situation which, if not avoided,
will result in death or serious injury.
CAUTION
CAUTION indicates a potentially haz-
ardous situation which, if not avoided,
may result in minor or moderate injury.
Safety Definitions
This is the safety alert symbol. It is
used to alert of potential personal injury
hazards. Obey all safety messages that
follow this symbol to avoid possible injury
or death.
Safety Instructions
DO NOT store or use gasoline, or
other flammable liquids in the vicinity
of this or any other appliance. Read
product labels for warnings regarding
flammability and other hazards.
DO NOT operate the unit in the
presence of explosive fumes.
Avoid contact with any moving parts
of automatic ice maker.
Remove all staples from the carton.
Staples can cause severe cuts, and also
destroy finishes if they come in contact
with other appliances or furniture.
WARNING
Please read all instructions before using
this appliance.
Child Safety
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision
or instruction concerning use of the
appliance by a person responsible for
their safety.
Destroy or recycle the carton, plastic
bags, and any exterior wrapping material
immediately after the appliance is
unpacked. Children should NEVER use
these items to play. Cartons covered with
rugs, bedspreads, plastic sheets or stretch
wrap may become airtight chambers, and
can quickly cause suocation.
IMPORTANT SAFETY INFORMATION
DANGER
DANGER Risk of fire or explosion.
Flammable refrigerant used. Do not use
mechanical devices to defrost refrigera-
tor. Do not puncture refrigerant tubing.
DANGER Risk of fire or explosion.
Flammable refrigerant used. To be re-
paired only by trained service person-
nel. Use only manufacturer-authorized
service parts. Any repair equipment
used must be designed for flammable
refrigerants. Follow all manufacturer
repair instructions. Do not puncture
refrigerant tubing.
CAUTION
CAUTION Risk of fire or explosion.
Dispose of refrigerator properly
in accordance with the applicable
federal or local regulations. Flammable
refrigerant used.
CAUTION Risk of fire or explosion
due to puncture of refrigerant tubing.
Follow handling instructions carefully.
Flammable refrigerant used.
WARNING
CALIFORNIA RESIDENTS ONLY
Cancer and Reproductive Harm
www.P65Warnings.ca.gov
4
IMPORTANT SAFETY INFORMATION
WARNING
These guidelines must be followed to
ensure that safety mechanisms in this
unit will operate properly.
Electrical information
The appliance must be plugged into
its own dedicated 115 Volt, 60 Hz.,
15 Amp, AC only electrical outlet.
The power cord of the appliance
is equipped with a three-prong
grounding plug for your protection
against electrical shock hazards.
It must be plugged directly into a
properly grounded 3-prong recepta-
cle. The receptacle must be installed
in accordance with local codes and
ordinances. Consult a qualified elec-
trician. Avoid connecting the unit to a
Ground Fault Interrupter (GFI) circuit.
Do not use an extension cord or
adapter plug.
If the power cord is damaged, it
should be replaced by an authorized
service technician to prevent any risk.
Never unplug the appliance by pull-
ing on the power cord. Always grip
the plug firmly, and pull straight out
from the receptacle to prevent dam-
aging the power cord.
Unplug the unit before cleaning and
before replacing the AC LED light
Grounding type wall receptacle
Power cord with
3-prong grounded plug
Do not, under
any circumstances,
cut, remove,
or bypass the
grounding prong.
IMPORTANT
CFC/HCFC Disposal
Your old unit may have a cooling system
that used CFCs or HCFCs (chlorofluoro-
carbons or hydrochlorofluorocarbons).
CFCs and HCFCs are believed to harm
stratospheric ozone if released to the
atmosphere. Other refrigerants may
also cause harm to the environment if
released to the atmosphere.
If you are throwing away your old ap-
pliance, make sure the refrigerant is re-
moved for proper disposal by a qualified
technician. If you intentionally release
refrigerant, you may be subject to fines
and imprisonment under provisions of
environmental legislation.
IMPORTANT
Turn o power to your appliance you
must unplug the power cord from the
electrical outlet.
CAUTION
To avoid personal injury or property
damage, handle tempered glass shelves
carefully. Shelves may break suddenly
if nicked, scratched, or exposed to sud-
den temperature change.
Proper Disposal of your Appliance
Risk of child entrapment
Child entrapment and suocation are not
problems of the past. Junked or aban-
doned appliances are still dangerous –
even if they will sit for “just a few days”. If
you are getting rid of your old unit, please
follow the instructions below to help pre-
vent accidents.
We strongly encourage responsible appli-
ance recycling/disposal methods. Check
with your utility company or visit ener-
gystar.gov/recycle for more information
on recycling your old appliance.
Before you throw away your appliance:
Remove doors.
Leave shelves in
place so children
may not easily
climb inside.
Have refrigerant
removed by a
qualified service
technician.
bulb to avoid electrical shock. Use a
5-watt or less AC LED light bulb only.
Performance may be aected if the
voltage varies by 10% or more. Oper-
ating the appliance with insucient
power can damage the compressor.
Such damage is not covered under
your warranty.
Do not plug the unit into an electrical
outlet controlled by a wall switch or
pull cord to prevent the unit from
being turned o accidentally.
5
FEATURES
A Adjustable Door Bins
B Shelves
C Ice Container
D Fixed Door Bins
E Ice Maker
F Damper/Air filter housing
G Refrigerator LED Light Cover
H Water Filter
I Dairy Compartment
J Temperature Sensor/Thermistor
K Deli Drawer (some models)
L Crisper Pan
M Toe Grille
N Slide Out Basket
IMPORTANT
Accessories are available for your appliance and may be purchased at
Frigidaire.com or by calling 1-800-374-4432 (Frigidaire.ca or 1-800-265-8352 in
Canada) or from an authorized seller.
*Features may vary according to model
L
M
N
B
C
D
E
F
G H
I
J
K
A
B
6
INSTALLATION
NOTE
If your unit is placed with the door hinge
side against a wall, you may have to
allow additional space for the handle so
the door can be opened wider.
This Use & Care Guide provides general
operating instructions for your model. Use
the unit only as instructed in this Use &
Care Guide. Before starting the appli-
ance, follow these important first steps.
Installation
Installation clearances
Allow the following clearances for ease
of installation, proper air circulation, and
plumbing and electrical connections:
Sides & Top "
Back 1".
Location
Choose a place that is near a ground-
ed electrical outlet. Do Not use an
extension cord or an adapter plug.
If possible, place the unit out of direct
sunlight and away from the range,
dishwasher or other heat sources.
Install the appliance on a floor that is
level and strong enough to support a
fully loaded unit.
Consider water supply availability for
models equipped with an automat-
ic ice maker. If you do not hook up
water to the appliance, remember to
turn the ice maker o.
CAUTION
Do Not install the unit where the tem-
perature will drop below 55°F (13°C) or
rise above 110°F (43°C). The compres-
sor will not be able to maintain proper
temperatures inside the appliance.
Do Not block the toe grille on the lower
front of your unit. Sucient air circula-
tion is essential for the proper opera-
tion of your appliance.
Toe Grille Installation and Removal
To install toe grille
1. Open both doors. Slide the left and
right sides of the toe grille over the
lower hinges of the appliance.
2. While pushing the toe grille firmly
against cabinet, fasten the bottom
clips of toe grille to the cabinet.
3. Fasten the top clips to the cabinet.
4. Close the doors. Fasten the right
and left side clips into the groove of
the bottom hinge.
To remove the toe grille
1. With both doors closed, unfasten
the right and left side clips of toe
grille from the bottom hinge groove.
2. Open both doors. Press firmly on the
top of the toe grille until the top of
the toe grille pops o.
3. Pull the toe grille outward toward
your body and o of the lower hinges.
1
2
3
2
3
1
4
4
Installing Toe Grille
1
2
3
2
3
1
Removing Toe Grille
7
INSTALLATION
Door Opening
Position your unit to allow easy access to
a counter or table when removing food.
For the best use of drawers and freezer
baskets, position the appliance where
both doors can fully open.
Guidelines for final positioning
of your unit:
Rest all 4 corners of the cabinet
firmly on the floor.
Level the cabinet at the front and rear.
Tilt the sides ¼" (6 mm) from front
to back (to ensure the doors close
and seal properly).
Align the doors with each other
and level.
NOTE
The doors are designed to shut by
themselves within a 20 degree opening.
Meet all of these conditions by
raising or lowering the adjust-
able front rollers.
To level the cabinet using the front rollers:
1. Open both doors and remove
the toe grille (see “Toe Grille
Installation and Removal” in the
INSTALLATION section).
2. Close the doors and use a wrench
to raise (clockwise) or lower
(counterclockwise) the front rollers.
3. Ensure both doors are bind-free with
their seals touching the cabinet on all
4 sides.
8
Set Screw
(some models)
Hinge
Hinge
Flange
Open Door
7/16" Wrench and
3/32" Hex Key (some models)
Door Stop
Flange
5. Reinstall the set screw, locking the
door height.
6. Replace the toe grille by fitting it
into place (see “Toe Grille Installation
and Removal” in the INSTALLATION
section).
4. After leveling, verify the door stop
contacts the lower hinge and the
top of the door does not contact the
upper hinge through full movement
of the door (from fully closed to
fully open).
INSTALLATION
To level the doors using the adjustable
lower hinge:
1. Before leveling either door, remove
the set screw that locks the door
height into position. (The door
cannot be adjusted without the set
screw removed).
2. If the refrigerator door is lower than
the freezer door, raise the refrigera-
tor door by turning the adjustment
screw counterclockwise using a
7
/
16
"
wrench. (See illustration.)
3. If the freezer door is lower than the
refrigerator door, raise the freezer
door by turning the adjustment
screw counterclockwise using a
7
/
16
"
wrench. (See illustration.)
NOTE
Some models will not have a set screw. For
those models follow steps 2 through 4.
9
DOOR REMOVAL
To prepare for removing the doors:
1. Make sure the electrical power cord
is unplugged from the wall outlet.
2. Open both doors and remove the
toe grille (as explained in the Instal-
lation Instructions that came with
your appliance).
3. Remove any food from the door shelves.
4. Close the doors.
To remove the refrigerator top hinge/cover:
1. Remove the 2 screws from the cover
over the top door hinge.
2. Lift hinge cover straight up and o.
3. Trace lightly around the door’s top
hinge with a pencil. This makes
reinstallation easier.
4. Remove the 2 screws from the top
hinge and lift the hinge straight up.
Lift the door o of the bottom hinge
and set it aside.
5. Remove the 2 bottom hinge screws
and hinge if necessary.
Socket
Wrench Set
Adjustable
Wrench
Top Hinge
Cover Front
Screw
Top
Hinge
Screw
Bottom
Hinge
Screw
Top Hinge
Cover Rear
Screw
Phillips™
Head
Tools Necessary:
or
or
⅜" Fixed
Wrench
Phillips™
Head
&
Flathead
Screwdriver
To reinstall the refrigerator door, reverse
the above steps.
Door
Hinge
Assembly
Closer
Pin
Hinge
Screws
Adjustable Hinge
10
DOOR REMOVAL
CAUTION
Be sure doors are set aside in a secure
position where they cannot fall and
cause personal injury.
Door
Hinge
Assembly
Screws
Water
Line
Tubing
Non-Adjusting Hinge (some models)
Closer
Pin
Hinge
Door
Water
Line
Tubing
Screws
Hinge
Assembly
Adjustable Hinge (some models)
To remove the freezer top hinge cover:
1. Remove the 2 screws from the cover
over the top door hinge.
2. Lift hinge cover straight up and o.
To remove the freezer door:
1. Remove the connector cover, insert
flat blade screwdriver into the snap
feature and twist.
2. Disconnect the 2 multi-wire ca-
ble connectors located above the
top hinge. Grasp both sides of the
connector firmly, press the connec-
tor lock and pull apart. Remove the
ground screw.
3. Trace lightly around the hinge with a
pencil. This makes reinstallation easier.
4. Detach the water tube from the
connector located below the freezer
door. The connector releases when
you press its outer sleeve inward.
5. Remove the 2 screws from the top
hinge and lift the hinge straight
up, pulling the 2 multi-wire cables
through it. Lift the door o of the
bottom hinge.
6. Remove the 2 bottom hinge screws
and hinge if necessary.
7. Lay the door on its side to avoid
damage to the water tube extending
from the bottom hinge.
To reinstall the freezer door, reverse the
above steps.
1. Press outer ring against face of
fitting
2. Pull to
remove tube
Insert tube and push until mark
To Connect
11
DOOR HANDLE INSTALLATION
1. Remove handles from carton and
any other protective packaging.
2. Position the freezer handle end caps
over the upper and lower pre-in-
stalled shoulder bolts (A) that are
fastened into door, ensuring the
holes for the set screws are facing
toward the refrigerator door.
3. While holding the handle firmly
against door, fasten the upper and
lower Allen set screws (B) with the
supplied Allen wrench.
4. Repeat steps 2 and 3 to install refrig-
erator handle. Ensure the holes for
the set screws are facing towards the
freezer door.
Freezer
Upper
End Cap
Door
Refrigerator
Upper
End Cap
Door
Refrigerator
Lower
End Cap
Door
Freezer
Lower
End Cap
Door
Ensure Handle Set Screws are Facing Each Other with Doors Closed
CAUTION
Wear gloves and safety goggles and
use extreme CAUTION when installing
these handles. The rounded end of the
handles may be sharp (some models).
IMPORTANT
To ensure proper installation of handles,
please review these instructions and il-
lustrations thoroughly prior to installing
the handles.
NOTE
Tighten and sub-flush all set screws (place the Allen set screw just below the sur-
face of the end cap) of the handle end cap. Draw the end caps tight to the freezer
and refrigerator doors with no gaps. To avoid scratching the metal door, keep the
door open while torquing down the set screws.
12
WATER SUPPLY CONNECTION
Before Installing The Water Supply Line,
You Will Need:
Basic Tools: adjustable wrench,
flat-blade screwdriver, and Phillips
TM
screwdriver
Access to a household cold water
line with water pressure between 30
and 100 psi.
A water supply line made of ¼" (6.4
mm) OD, copper or stainless steel
tubing. To determine the length of
tubing needed, measure the distance
from the ice maker inlet valve at the
back of the refrigerator to your cold
water pipe. Then add approximately
7� (2.1 m), so the refrigerator can be
moved out for cleaning.
To Connect Water Supply Line To Ice
Maker Inlet Valve
1. Disconnect the refrigerator from
electrical power source.
2. Place the end of the water supply
line into a sink or bucket. Turn ON
the water supply and flush the supply
line until the water is clear. Turn OFF
the water supply at the shuto valve.
3. Remove the plastic cap from the wa-
ter valve inlet and discard the cap.
4. If you use copper tubing - Slide the
brass compression nut, and then
the ferrule (sleeve) onto the water
supply line. Push the water supply
line into the water valve inlet as far
as it will go (¼"/6.4 mm). Slide the
ferrule (sleeve) into the valve inlet
and finger tighten the compression
nut onto the valve. Tighten another
half turn with a wrench; DO NOT
overtighten. See Figure 1.
A shuto valve to connect the water
supply line to your household water
system. DO NOT use a self-piercing
type shuto valve.
Do not reuse compression fitting or
use thread seal tape.
A compression nut and ferrule
(sleeve) for connecting a copper
water supply line to the ice maker
inlet valve.
WARNING
To avoid electric shock, which can
cause death or severe personal injury,
disconnect the unit from electrical pow-
er source before connecting a water
supply line to the appliance.
CAUTION
To Avoid Property Damage:
Use Copper or Stainless Steel braid-
ed tubing for the water supply line.
Frigidaire does not recommend wa-
ter supply tubing made of ¼" plastic.
Plastic tubing greatly increases the
potential for water leaks, and the
manufacturer will not be responsible
for any damage if plastic tubing is
used for the supply line.
DO NOT install water supply tubing
in areas where temperatures fall
below freezing.
Chemicals from a malfunctioning
softener can damage the ice maker.
If the ice maker is connected to soft
water, ensure that the softener is
maintained and working properly.
IMPORTANT
Ensure that your water supply line connec-
tions comply with all local plumbing codes.
NOTE
Check with your local building author-
ity for recommendations on water
lines and associated materials prior to
installing your new refrigerator. Depend-
ing on your local/state building codes,
Frigidaire recommends for homes with
existing valves its Smart Choice
®
water
line kit 5304490728 (with a 6�Stainless
Steel Water Line) and for homes without
an existing valve, Frigidaire recom-
mends its Smart Choice
®
water line kit
5304490717 (with a 20�copper water
line with self-tapping saddle valve).
Please refer to www.frigidaire.com for
more information.
13
WATER SUPPLY CONNECTION
If you use braided flexible stainless
steel tubing - The nut is already
assembled on the tubing. Slide the
nut onto the valve inlet and finger
tighten the nut onto valve. Tighten
another half turn with a wrench; DO
NOT overtighten. See Figure 2.
IMPORTANT
After connecting the water supply, refer
to “Priming the Water Supply System
for important information about priming
an empty water supply system.
Your refrigerator’s water supply system
includes several tubing lines, a water
filter, and a water valve. To ensure that
your water dispenser works properly,
completely fill this system with water
when you first connect your refrigerator
to the household water supply line.
5. With the steel clamp and screw,
secure the water supply line (copper
tubing only) to the rear panel of
refrigerator as shown.
6. Coil the excess water supply line
(copper tubing only), about 2½ turns,
behind refrigerator as shown and
arrange coils so they do not vibrate or
wear against any other surface.
7. Turn ON the water supply at shuto
valve and tighten any connections
that leak.
8. Reconnect the refrigerator to elec-
trical power source.
A B
C
D
E
F
G
H
I
Figure 1
A Plastic Water Tubing to
Ice Maker Fill Tube
B Steel Clamp
C Brass Compression Nut
D Ferrule (Sleeve)
E Copper Water Line
F Water Valve Bracket
G Valve Inlet
H Water Valve
I Copper Water Line from
Household Water Supply*
J Braided Flexible Stainless Steel
Water Line
K 6 ft. (1.8 m) Braided Flexible
Stainless Steel Water Line from
Household Water Supply*
*Include enough tubing in the loop to allow
moving the refrigerator out for cleaning
A B
J
F
G
H
K
Figure 2
14
CONTROLS AND SETTINGS
NOTE
Your appliance may have some or all of the features listed below. Become familiar
with these features and their use and care.
Cube
Press the Cube button to get cubed ice. A white LED light will indicate
the mode is selected. Press glass against the ice dispensing paddle as far
up as possible to catch all the ice.
Crush
Press the Crush button to get crushed ice. A white LED light will indicate
the mode is selected. Press glass against the ice dispensing paddle as far
up as possible to catch all the ice.
Light
Press the light button to turn on the dispenser light. A white LED light
will indicate the dispenser light is on. Press again to turn the light o.
Water
To operate the water dispenser, press a glass against the Water
dispensing paddle. To stop dispensing water, pull the glass away from
the dispensing paddle. Dispensed water is not cold. For colder water, add
crushed ice or cubes before dispensing water.
Water
Filter
Status
When you need to order a new water filter, the side door UI will change
to the Order status. When you need to replace the water filter, the Side
Door UI will change to the red replace status and the front UI will display
Replace Water Filter. After you change the filter, hold the Water Filter
button for 3 seconds to reset.
Air
Filter
Status*
When you need to order a new air filter, the Side Door UI will change to
the Order status. When you need to replace the air filter, the Side Door
UI will change to the red Replace status and the Front UI will display
Replace Air Filter. After you change the filter, hold the Air Filter button
for 3 seconds to reset.
*Only on some models
Front of Door User Interface
15
Power
Outage
In the event of a power outage where the internal temperature of the re-
frigerator rises above the safe temp zone, the Power Outage warning will
appear to remind you to check your food. In addition to the indicator, an
alarm will sound every 60 seconds until acknowledged. Press any button
to clear the alarm.
In the event of a power outage, where the internal temperature of the
refrigerator stays within the safe temp zone, no warning or alarm will
activate when the power is restored.
Door
Open
When a door is open the Door Open indicator will appear and will
disappear when the door is closed. If a door is left open for more than
5 minutes an alarm will sound. The alarm will continue to go o every
10 seconds until acknowledged. Close the door to turn o the alarm or
press any button on the control to temporarily disable the alarm.
High
Temp
In the event of the internal temperature of the refrigerator rising and
staying at a temperature above the safe temp zone for a period of time,
the High Temp warning will appear to remind you to check your food.
In addition to the indicator, an alarm will sound every 10 seconds until
acknowledged. Press any button to clear the warning.
The refrigerator will automatically try to cool down to improve the con-
dition. However, if the temperature has not cooled after some time, the
warning and alarm will appear again. If the problem continues please call
1 (800) 372-4432.
Alarms
CONTROLS AND SETTINGS
16
CONTROLS AND SETTINGS
Active Mode View
Inactive Mode View
Sleep Mode View
In-Door User Interface
17
Temperature
Adjustment
Adjust the temperature gradually: adjust in small increments, allow-
ing the temperature to stabilize.
For colder temperatures, press the Temp button to change the
temperature setting toward Coldest.
For warmer temperatures, press the Temp button to change the
temperature setting toward Cold.
Adjusting the refrigerator control will change temperature in both
compartments. The freezer control can be left at the factory preset
(*Recommended) or adjusted as desired.
To maintain temperatures, a fan circulates air in the refrigerator and
freezer compartments. For good circulation, do not block cold air
vents with food items.
Air Filter
Status*
The display shows the current status of the air filter (Good, Order, or
Replace). To reset the filter status to Good, press and hold Air Filter
for 3 seconds.
Water Filter
Status
The displays shows the current status of the water filter (Good,
Order, or Replace). To reset the filter status to Good, press and hold
Water Filter for 3 seconds.
*Only on some models
In-Door Control Display Mode Views
Your display is equipped with a sleep and inactive mode to prevent accidental changes
to the unit settings during opening and closing of the doors. When both doors are
closed, the display will be in sleep mode. When either door is first opened, the display
will be in inactive mode where all the current settings are visible but dimmed.
Pressing any button on the display will activate the display and a tone will be played.
All settings will then be fully lit. Touch the display again to change any setting.
If there is no button pressed for 10 seconds while any door is open, the display will
default back to inactive mode.
CONTROLS AND SETTINGS
18
AUTOMATIC ICE AND WATER DISPENSER
Priming the water supply system
Ice maker operation & care
After you properly install the refrigerator
and it has cooled for several hours, the ice
maker can produce ice within 24hours.
The ice maker will fill the ice bin from the
rear. You must dispense some ice to force
the ice forward in the bin. This will allow
the bin to fill completely.
1. Begin filling
the system
by pressing
and holding
a drinking
glass against
the water
dispenser
paddle.
2. Keep the
glass in this
position until
water comes
out of the
dispenser. It may take about
1½ minutes. Water will sputter until
you purge all air from the water lines.
3. Continue dispensing water for about
4 minutes to flush the system
and plumbing connections of any
impurities (stopping to empty the
glass as necessary).
Power Outage
Cube
ICE
WATER
Crush
Door Open
High Temp
Replace Water Filter
Replace Air Filter
Dispenser
(varies by model)
CAUTION
For proper dispenser operation, the
recommended water supply pressure
should fall between 30psi and 100psi.
Excessive pressure may cause the sys-
tem to malfunction.
NOTE
Dispensed water is not chilled. For
colder water, add ice to cup or contain-
er before dispensing water.
NOTE
The ice maker also has a built-in plastic
signal arm that automatically stops ice
production when the ice bin is full. Do
not use this signal arm to manually stop
the ice maker.
IMPORTANT
Turning o the ice maker simply dis-
ables ice making. You will still be able to
dispense existing ice, and you will still be
able to dispense water.
Turning the ice maker on
To turn the ice maker on, press the ice
maker's On/O power switch, located on
the front of the ice maker, so the LED is
steadily illuminated.
19
Ice Maker/Dispenser Tips
Ice cubes stored too long may
develop an odd flavor. Empty the ice
container as explained in Cleaning the
Ice Storage Bin.
Occasionally shake the ice container
to keep ice separated.
If your refrigerator is not connected to
a water supply or the water supply is
turned o, turn O the ice maker.
If you need a large quantity of ice
at one time, it is best to get cubes
directly from the ice container.
The following sounds are normal
when the ice maker is operating:
- Motor running
- Ice dropping into ice container
- Water valve opening or closing
- Ice loosening from tray
- Running water
When dispensing ice, you will hear a
snapping or clicking sound when the
ice chute opens and closes.
Turn O the ice maker when cleaning
the freezer and during vacations. If
you turn O the ice maker for a long
period of time, you should also turn
o the water supply valve.
Cleaning the Ice Storage Bin
Clean the ice storage bin at regular
intervals, particularly before you take a
vacation or move.
To clean the ice storage bin:
1. Turn O the ice maker.
2. Remove the ice storage bin by lifting
up and out.
3. Empty and carefully clean the ice
storage bin with mild detergent.
Rinse with clear water. Do not use
harsh or abrasive cleaners.
CAUTION
Chemicals from a malfunctioning water
softener can damage the ice maker. If
the water supply to your refrigerator is
softened, be sure the softener is main-
tained to work properly.
CAUTION
NEVER use an ice pick or similar sharp
instrument to break up the ice. This
could damage the ice storage bin and
dispenser mechanism.
4. Allow the ice storage bin to dry com-
pletely before replacing it in the freezer.
5. Remove ice chips and clean the ice
storage bin, shelf and the freezer
door chute.
6. Replace the ice storage bin. Turn On
the ice maker to resume ice production.
Remove and empty the ice storage bin if:
An extended power failure (1 hour or
longer) causes ice cubes in the ice
storage bin to melt and freeze togeth-
er, jamming the dispenser mechanism.
You do not use the ice dispenser
frequently. Ice cubes will freeze
together in the bin, jamming the
dispenser mechanism.
Remove the ice storage bin and shake
to loosen the cubes or clean as
explained above.
AUTOMATIC ICE AND WATER DISPENSER
Auger
IMPORTANT
When removing or replacing the ice stor-
age bin, avoid rotating the auger in the
ice storage bin. If the auger is accidental-
ly rotated, you must realign the auger by
turning it in 45 degree turns (see below)
until the ice storage bin fits into place
with the drive mechanism If the auger is
not properly aligned when replacing the
ice storage bin, the refrigerator will not
dispense ice. The freezer door also may
not close properly causing warm air to
leak into the freezer compartment.
20
STORAGE FEATURES
Glass Shelf
Glass Shelf Adjustment
Shelves are easily adjusted to suit individ-
ual needs. Before adjusting the shelves,
remove all food. Shelves are supported by
side rails.
To adjust, lift up on the back of the shelf
and pull forward.
Replace the shelf by sliding it on top of
the formed rails on the side walls of the
cabinet until the rear plastic hooks of the
shelf lock into the rear of the cabinet liner.
Door storage
Door bins and shelves are provided for
convenient storage of jars, bottles, and
cans. You can quickly select frequently
used items.
Some models have door bins that can
accommodate gallon-sized plastic drink
containers and economy-sized jars and
containers. Some bins are adjustable for
maximum storage capacity.
The dairy compartment, which is warmer
than the general food storage section,
is intended for short term storage of
cheese, spreads, or butter.
Crisper Drawer
Crispers
Crispers allow you the flexibility to store
any manner of items including fruits, veg-
etables, nuts, etc. Crispers do not feature
humidity controls.
Deli Drawer (some models)
Some models are equipped with a Deli
Drawer for storing luncheon meats,
spreads, cheeses and other deli items.
This drawer does not have a separate
temperature control.
CAUTION
To avoid personal injury or property
damage, handle tempered glass shelves
carefully. Shelves may break sudden-
ly if nicked, scratched, or exposed to
sudden temperature change. Allow the
glass shelves to stabilize to room tem-
perature before cleaning. Do not wash
in dishwasher.
Deli Drawer
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96

Frigidaire FRSS2323AW Manuel utilisateur

Catégorie
Frigos
Taper
Manuel utilisateur