MartinLogan Outdoor Living Foundation 8.1 System Manuel utilisateur
- Catégorie
- Haut-parleurs de voiture
- Taper
- Manuel utilisateur
Register your warranty online at www.MartinLogan.com.
user’s manual
OUTDOOR LIVING
™
SERIES
111120
2
EN |
TABLE OF CONTENTS
Overview............................3
Outdoor Living™ Foundation Music System .........3
Contents of the System ......................3
Additional Required Components (Sold Separately) ...3
Required Tools ...........................3
Power .................................3
Planning the System Layout ..............4
Cable Recommendations ................5
Installation Considerations ...............5
Wiring & Speaker Installation ............6
Stereo Setup Using 4 Conductor Burial Cable
& Amplifier (Option 1) ......................6
Stereo Setup Using 4 Conductor Burial Cable
& Amplifier (Option 2) ......................7
Mono Setup Using 2 Conductor Burial Cable
& Amplifier (Option 3) ......................8
Preparing the 4 Conductor Burial Cable
(For Stereo Setup) .........................9
Preparing the 2 Conductor Burial Cable
(For Mono Setup) ........................10
Attaching Ground Stake to Speaker & Installation ...11
Cable Connections from Speaker to RED (+) and
BLACK (–) Burial Cable ....................12
Cable Connections from Speaker to WHITE (+) and
GREEN (–) Burial Cable ......................12
Cable Connections from Subwoofer to Burial Cable....13
Test System .........................14
To Avoid Speaker Damage..............14
Listening Outdoors....................14
Limited Warranty.....................15
Serial Number | Numéro de série
3| EN
MartinLogan Outdoor Living™ Foundation
Music System
The MartinLogan Outdoor Living Foundation Music System
includes 8 premium all-season outdoor speakers and 1 all-
season in-ground subwoofer ideal for backyards ranging
from 2,000 to 3,000 sq. ft.
Made of durable UV treated ABS plastic and thick high-
density polyethylene, the Outdoor Living Foundation Music
System can endure the elements while providing years of
trouble-free service.
While installation is relatively easy, MartinLogan’s Outdoor
Living Foundation Music System is designed to be installed
by your authorized MartinLogan dealer.
WARNING!
• ACCOUNT FOR POTENTIAL ELECTRICAL,
GAS, BURIED CABLES, PLUMBING OR
OTHER OBSTACLES BEFORE DIGGING.
• MANY LOCALITIES FORBID DIGGING
WITHOUT PRIOR NOTIFICATION.
CONTACT LOCAL AUTHORITIES BEFORE
INSTALLATION.
• READ AND FOLLOW ALL INSTRUCTIONS
BEFORE BEGINNING.
Contents of the System:
• (8) Speakers with Mounting Stakes
• (1) In-Ground Subwoofer with Canopy
• (20) Silicone-Filled Wire Connectors
Additional Required Components
(Sold Separately):
• Burial Speaker Cable
• Wire Ties (Optional)
Required Tools:
• Shovel
• Cable Strippers
Power
Any 8 ohm stereo amplifier (for Stereo Setup) or
Any 4 ohm mono amplifier (for Mono Setup)
OVERVIEW
4
EN |
=
=
The MartinLogan Outdoor Living Foundation Music System
is designed to deliver seamless, and evenly distributed
sound coverage in an ‘open air’ environment. The following
illustration shows how a daisy chain of satellite speakers and
a subwoofer should be strategically placed to create even,
balanced coverage around the outdoor environment. The
satellite speakers should be spaced from 6 to 10 feet (2.4 -
3 meters) apart for optimal coverage. With a tighter spacing,
more satellites will be required to fill out an area, but with the
advantage of more consistent coverage and volume levels
across the intended entertainment area.
To achieve the best balance between the satellites and
subwoofer, the subwoofer should be placed as close to the
center of the satellites as possible. Keep in mind that this
is simply a suggestion and that your unique environment
may dictate otherwise. If more bass is desired, placing the
subwoofer near a wall or other solid surface will greatly
reinforce the low bass frequencies.
Checklist:
q Identify the location.
q Determine the positioning of the satellite speakers
and subwoofer.
q Dig the trench according to satellite speakers and
subwoofer to be installed.
q The trench should be 6”- 8” deep.
PLANNING THE SYSTEM LAYOUT
5| EN
We strongly recommend using burial-rated cable (not
included) when installing the Outdoor Living Foundation
Music System. In addition, it’s critical to use the proper
speaker cable gauge. Please review the chart below.
There are a few considerations before you start digging a trench:
• Ensure that your ENTIRE system is tested prior to installation.
• Ensure that the proposed area is easily accessed and that
the area is not prone to flooding, standing water or where
the speakers and subwoofer can be easily damaged,
kicked or struck.
• Consider overall landscape/garden design and
positioning in relation to the listening area.
CABLE RECOMMENDATIONS
INSTALLATION CONSIDERATIONS
CABLE GAUGE CHART
Cable Gauge Distance
18 Gauge Up to 100 feet (30 meters)
16 Gauge Up to 150 feet (45 meters)
14 Gauge Up to 200 feet (61 meters)
12 Gauge Up to 400 feet (122 meters)
6
EN |
WIRING & INSTALLATION
Stereo Setup Using 4 Conductor Burial Cable & Amplifier (Option 1)
Stereo Wiring Diagram (Option 2)
4 Conductor Burial Wire
–+
–+
Black Red
Green White
+
–
–+
4 Conductor Burial Wire
–+
–+
Black Red
Green White
+
–
–+
Left
8 Ohm Stereo 2-Channel Amplifier
Left Left Left Left & Right Left & Right
Stereo Wiring Diagram (Option 1)
Right Right Right Right
Left
8 Ohm Stereo 2-Channel Amplifier
Right Left Right Left & Right Left & Right Left Right Left Right
The satellite speakers included in this system individually
present a 32 ohm load to the amplifier. When 4 of them
are connected on each amplifier channel in parallel,
the load to the amplifier is approximately 8 ohms. The
nominal impedance of the subwoofer is 8 ohms per
channel. The satellites and subwoofer feature optimized
internal crossovers so that the subwoofers impedance is not
combined with the satellites. The overall load presented to
your amplifier by the combined system of 8 satellites and 1
subwoofer will be around 8 ohms nominal per channel.
With these considerations in mind, multiple system wiring
possibilities are possible. The following diagrams are
simple, and safe examples of wiring the system to a
traditional 8 ohm stereo amplifier. If using an alternative
wiring or amplification configuration, please take care to
ensure that the impedance presented to your amplifier is
within its published specifications. Failure to adhere to the
above guidance could result in damage to the speakers
and/or the amplifier which MartinLogan will not take
responsibility for and will not be covered under warranty.
NOTE: If using the MartinLogan MP500 Amplifier:
Use DSP Preset 5 =
Starting with switch #2 (Down, Down, Up, Down, Up)
NOTE: This configuration is for a row of 4x Left Channel Speakers and a
row of 4x Right Channel Speakers with the subwoofer placed in between.
The above diagram is for illustration purposes only. If you wish to wire the
subwoofer in a different location, feel free to wire it in line with the speakers
wherever is the most convenient for you. As long as you have 4x speakers
and 1x voice coil of the subwoofer per amplifier channel, it does not matter
the order in which they are wired together.
7| EN
Stereo Setup Using 4 Conductor Burial Cable & Amplifier (Option 2)
WIRING & INSTALLATION (CONT’D)
Stereo Wiring Diagram (Option 2)
4 Conductor Burial Wire
–+
–+
Black Red
Green White
+
–
–+
4 Conductor Burial Wire
–+
–+
Black Red
Green White
+
–
–+
Left
8 Ohm Stereo 2-Channel Amplifier
Left Left Left Left & Right Left & Right
Stereo Wiring Diagram (Option 1)
Right Right Right Right
Left
8 Ohm Stereo 2-Channel Amplifier
Right Left Right Left & Right Left & Right Left Right Left Right
NOTE: If using the MartinLogan MP500 Amplifier:
Use DSP Preset 5 =
Starting with switch #2 (Down, Down, Up, Down, Up)
NOTE: This configuration is for alternating stereo pairs of speakers with the
subwoofer placed in between. The wiring is essentially identical to “Option
1” with only the order/placement of the speakers and subwoofer changing.
The above diagram is for illustration purposes only. If you wish to wire the
subwoofer in a different location, feel free to wire it in line with the speakers
wherever is the most convenient for you. As long as you have 4x speakers
and 1x voice coil of the subwoofer per amplifier channel, it does not matter
the order in which they are wired together.
8
EN |
Mono Setup Using 4 Conductor Burial Cable & Amplifier (Option 3)
Mono
4 Ohm Mono 1-Channel Amplifier
Mono Mono Mono Mono
Mono Wiring Diagram (Option 3)
Mono Mono Mono Mono
Mono
2 Conductor Burial Wire
Black Red
+
–
–+
4 Ohm Mono 1-Channel Amplifier Mono
Mono Wiring Diagram (Option 3)
Mono
2 Conductor Burial Wire
Black Red
+
–
–+
4 Ohm Mono 1-Channel Amplifier Mono
Mono Wiring Diagram (Option 3)
2 Conductor Burial Wire
Black Red
+
–
–+
To Sub
To Adjoining Amp,
Sub or Speaker To Adjoining,
Sub or Speaker
NOTE: *If using the MartinLogan MP500 Amplifier:
Use DSP Preset 6 =
Starting with switch #2 (Down, Down, Up, Up, Down,) MP500 will be in
Bridged Mono mode. Follow the markings on the MP500 to ensure proper
wiring polarity while in Bridged Mode.
NOTE: This configuration is for mono operation.
This means the output of each speaker will be
the same (all speakers play a combination of
Left and Right). This is ideal for providing even
and consistent coverage across your space. The
above diagram is for illustration purposes only.
If you wish to wire the subwoofer in a different
location, feel free to wire it in line with the speak-
ers wherever is the most convenient for you. As
long as you follow the subwoofer wiring illustra-
tion shown here, it does not matter where in the
line of speakers it is wired in.
9| EN
Preparing the 4 Conductor Burial Cable (For Stereo Setup)
3. Use a round
cable stripper to
remove the outside
protective cable
jacket to expose
the four color-
coded wires.
Separate the wire
loops as shown.
2. Recommended:
Use a wire tie
(not included) to
keep the wire
loop intact and
it will act as a
strain relief.
4. Cut the red (+)
and black (-)
OR white (+)
and green (-)
wires with cable
strippers and
strip off 1 inch
(25.4 mm) of
insulation to
expose the bare
wire conductor.
white (+) &
green (-)
red (+) &
black (-)
1. Starting with the
first speaker and
every speaker/
sub that comes
after, create a
loop approximate-
ly 6” in length.
WIRING & INSTALLATION (CONT’D)
10
EN |
Preparing the 2 Conductor Burial Cable (For Mono Setup)
1. Starting with the
first speaker and
every speaker/
sub that comes
after, create a
loop approximate-
ly 6” in length.
3. Use a round
cable stripper to
remove the outside
protective cable
jacket to expose
the two color-
coded wires.
Separate the
wire loops
as shown.
2. Recommended:
Use a wire tie
(not included) to
keep the wire
loop intact and
it will act as a
strain relief.
4. Cut the red (+)
and black (-)
wires with cable
strippers and
strip off 1 inch
(25.4mm) of
insulation to
expose the bare
wire conductor.
red (+)
black (-)
11 | EN
Attaching Ground Stake to Speaker & Installation
3. By hand, push the
speaker assembly
into the ground.
CAUTION:
DO NOT use
a hammer.
4. The speaker is
now installed.
The next step is
wiring, go to the
next page for
instructions.
2. To attach the
speaker to the
ground stake,
hand thread the
speaker to the
ground stake.
1. Thread the
speaker’s wiring
down through
the ground stake
and out of the
wiring hole
as shown.
WIRING & INSTALLATION (CONT’D)
12
EN |
Cable Connections from Speaker to RED (+) AND BLACK (-) Burial Cable
Cable Connections from Speaker to WHITE (+) AND GREEN (-) Burial Cable
To Speaker
To Speaker
To Adjoining
Amp, Sub or
Speaker
To Adjoining
Amp, Sub or
Speaker
To Adjoining,
Sub or Speaker
To Adjoining,
Sub or Speaker
Before you start wiring, please refer to the
wiring setup options on pages 6 to 8. Combine
and twist (clockwise) the Red wire (as shown in the diagram)
from a speaker or subwoofer to the Red wires from the burial
cable. Secure these three wires using the provided silicone-
filled wire connector; Repeat this procedure for the Black
wires. NOTE: You may have to cut some of the speaker cable
emanating from the speaker to a more manageable size.
Before you start wiring, please refer to the
wiring setup options on pages 6 to 8. Combine
and twist (clockwise) the Red wire (as shown in the diagram)
from a speaker or subwoofer to the White wires from the
burial cable. Secure these three wires using the provided
silicone-filled wire connector; Repeat this procedure for the
Black and Green wires. NOTE: You may have to cut some
of the speaker cable emanating from the speaker to a more
manageable size.
13 | EN
Cable Connections from Subwoofer to Burial Cable
To Sub
To Adjoining Amp,
Sub or Speaker To Adjoining,
Sub or Speaker
Before you start wiring, please refer to the
wiring setup options on pages 6 to 8. Combine
and twist (clockwise) the Red wire (as shown in the diagram)
from a speaker or subwoofer to the Red wires from the burial
cable. Secure these three wires using the provided silicone-
filled wire connector; Repeat this procedure for the Black,
Green and White wires. NOTE: You may have to cut some
of the speaker cable emanating from the subwoofer to a
more manageable size.
WIRING & INSTALLATION (CONT’D)
14
EN |
TEST SYSTEM
After all satellites and subwoofer connections are completed,
connect the wires to your receiver or amplifier.
IMPORTANT: Be sure not to let any stray ’+’ and
’-’ strands touch each other. Touching strands
will cause a short circuit that could damage your
amplifier.
Turn your receiver or amplifier ‘On’ and test the system with your
favorite music. If your system is operating properly, refill the wire
trench and enjoy your new speakers.
Contrary to popular belief, most speaker damage and
distortion occurs from using an amplifier with too little
power. The more available power an amplifier has, the
higher the threshold becomes before clipping occurs
(outputting damaging distortion), effectively raising
the useable volume of the system. Of course, going
overboard with power can allow the listener to exceed
the mechanical limits of the speakers and result in
speaker damage and distortion. However, when used
appropriately, a more powerful amplifier can reduce the
risk of distortion or speaker damage as the amplifier will
be able to continuously operate within
its intended “safe range” during normal playback of
the system.
If your speakers begin to sound harsh or grating, or if
you hear the bass breaking up, turn the volume down
immediately or you will damage your speakers! This type
of damage constitutes abuse and is not covered under
warranty.
Tone controls and equalizers can demand even more
power from an amplifier, lowering the point at which it
produces clipping distortion. Use them sparingly, if at all,
For areas larger than 3,000 sq. ft., we recommend using
multiple MartinLogan Outdoor Living Foundation systems.
Please note that powering multiple Outdoor Living Foundation
systems may require additional amplification to properly
integrate. Please consult your dealer for guidance on
amplifier capability and selection. Using more speakers
ensures that sound is not only more evenly distributed, but
also allows the system to be more easily heard at lower
listening levels. By doing this, demand on the amplifier is
reduced and neighbors are not disturbed. Think of it this
way: When lighting a large outdoor area, using multiple
floodlights on a dimmer set to a low setting is far more
effective than using a single floodlight with the dimmer
set to high.
TO AVOID SPEAKER DAMAGE
LISTENING OUTDOORS
15 | EN
The MartinLogan® Outdoor Living Foundation Music System
is warranted to be and remain free of manufacturing and/
or material defects for a period of three (3) years from the
date of original purchase. Within the time period specified,
repair, replacement or adjustment of parts for manufacturing
and/or material defects will be free of charge to the original
owner. Thermal or mechanical abuse/misuse is not covered
under warranty.
Limitations:
• Warranty begins on date of original retail purchase
from an Authorized MartinLogan® Dealer only. It is not
transferable.
• Warranty applies to product in normal residential use only.
If product is subjected to any of the conditions outlined in
the next section, warranty is void.
• Warranty does not apply if the product is used in
professional or commercial applications.
• Warranty also excludes normal cosmetic deterioration
caused by environmental conditions.
Warranty is Void if:
• The product has been abused (intentionally or
accidentally).
• The product has been used in conjunction with unsuitable
or faulty equipment.
• The product has been subjected to damaging signals,
derangement in transport, mechanical damage or any
abnormal conditions.
• The product (including cabinet) has been tampered with or
damaged by an unauthorized service facility.
• The serial number has been removed or defaced.
Owner Responsibilities:
• Provide normal/reasonable operating care and
maintenance.
• Provide or pay for transportation charges for product to
service facility.
• Provide proof of purchase (your sales receipt given at time
of purchase from your Authorized MartinLogan® Dealer
must be retained for proof-of-purchase date).
Should servicing be required, contact your nearest Authorized
MartinLogan® Dealer, MartinLogan Ltd. or Import Distributor
(outside the U.S. and Canada) to arrange, bring in or
ship prepaid, any defective unit. Visit our website,
www.martinlogan.com for more information.
MartinLogan Ltd. reserves the right to improve the design of
any product without assuming any obligation to modify any
product previously manufactured.
This warranty is in lieu of all other warranties expressed or
implied, of merchantability, fitness for any particular purpose
and may not be extended or enlarged by anyone. In no
event shall MartinLogan Ltd., their agents or representatives
be responsible for any incidental or consequential damages.
Some jurisdictions do not allow limitation of incidental or
consequential damages, so this exclusion may not apply
to you.
Retain this manual and your sales receipt for
proof of warranty term and proof of purchase.
LIMITED WARRANTY
NOTES
NOTES
g u i d e d e l ’ u t i l i s a t e u r
SUB 8
• 1 subwoofer
encastré au
sol avec dôme
• Fonctionne avec
n'importe quel
amplificateur
stéréo 8ohms
Inscrivez votre garantie en ligne à l’adresse www.MartinLogan.com.
111120
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
MartinLogan Outdoor Living Foundation 8.1 System Manuel utilisateur
- Catégorie
- Haut-parleurs de voiture
- Taper
- Manuel utilisateur