Sioux Tools IW38TB P-3P Operator Instructions Manual

Catégorie
Outils électroportatifs
Taper
Operator Instructions Manual

Ce manuel convient également à

Model IW38TB P-3PlI W38TBP-2Q
Impact Driver
Operator Instructions
^
Includes
-
Foreseen Use, Work Stations, Putting Into Service,
Ooeratina. Dismantlina. Assemblv and Safetv Rules.
Sioux Tools, Inc.
250 Snap-on Drive
P.O. Box 1596
Murphy, NC 28906
U.S.A.
Tel No. 828-835-9765 Fax No. 828-835-9685
Air Pressure
Product Net Weight
IW38TBP-3P 2.09 Ibs 0.95 kg
1W38TBP-2Q 2.13 Ibs 0.97 kg
Recommended Working
6.2
bar
90
PSI
Maximum
6.2
bar
90
PSI
Recommended Use Of
Balancer Or Support
NO
Personal
Safety
Equipment
Always
Read
Instructions
Use
-
Safety Glasses
YES
1
Before
Using
Power
Tools
@
/A&e;;&ar
Safety
Use
-
Safety Gloves
-If the tool appears to malfunction,
remove from use immediately and
arrange for service and repair. If it is
not practical to remove tool from
service, then shut off the air supply
to the tool and write or have written a
warning note and attach it to the tool.
-
If tool is to be used with a balancer or
other suspension device, ensure that
the tool is firmly attached to the
suspension/support device.
-
When operating the tool, always keep
Use
-
Safety Boots
Use
-
Breathing Masks
Use
-
Ear protectors
YES
Form
#
ZCE795
Date 2008
June
20lA
@
Wear
Hearing Protection
A
To
Vibration
Important
Safety rules
when
using IW38TBP-3P/
IW38TBP-2Q Impact Driver
-Use only impact sockets and extensions, universal
joints, etc. rated as being suitable for use withimpact
wrenches.
-
Prolonged exposure to vibration may cause injury.
-Read all instructions before using this tool. All
operators must be fully trained in its use and aware of
these safety rules.
-Do not exceed the maximum working air pressure.
-
Use personal protection equipment as recommended.
-
Some dust created by power sanding, sawing, grinding,
drilling, and other construction activities contains
chemicals known to cause cancer, birth defects and other
reproductive harm.
-Use only compressed air at the
recommended conditions.
7
Read these instructions carefully before installing, operating,
servicing or repairing this tool. Keep these instructions in a safe
accessible dace.
-
Product Type
,
Impact Driver
Recommended
Hose[
Recommended Max.
Cycles
Per
Min.
dodel NoINos
W38TBP-3P (3/8" Pin)
W38TBP-2Q
(1/4"
QCC)
Size
-
Minimum Hose Length
318
ins
10
mm
1
30Ft
10M
Serial No.
Noise Level:
Sound Pressure Level 84.0 dB(A)
Sound Power Level 95.0 dB(A)
Test Method:
Tested in accordance with Pneurop
test code PN8NTC1 and IS0 Standard 3744
Vibration Level
LessThan 2.5
Meters
I
Sec2
Test Method:
Tested in accordance with IS0
standards 8662 Parts 1
&
7
the body and particularly the hands away from the work-
ing attachment fixed to the tool.
-The tool is not electrically insulated. Never use the tool
if there is any chance of coming into contact with live
electricity.
-Always when using the tool, adopt a firm footing
and/or
position and grip the tool sufficiently only to overcome
any reaction forces that may result from the tool doing
work. Do not overgrip.
-Use only correct spare parts for maintenance and
repair. Do not improvise or make temporary repairs.
Major servicing and repairs should only be carried out
by persons trained to do so.
-
Do not lock, tape, wire, etc. the 'On/Off' valve in 'On'
position. The triggerllever, etc. must always be free to
return to the 'Off' position when released.
All
Pipe
And
Fittings
Should
Be
112'
Or
Large
Easy
To
Reach
And
Air
Tool
Recommended Air
supply
System
Figure
1
Page No
1
-Always shut off the air supply to the tool and press the
'OnIOff' valve to exhaust the air from the feed hose
before fitting, removing or adjusting the working
attachment fitted to the tool.
-Before using the tool, make sure that a shut off device
has been fitted to the air supply
lineand the position is
known and easily accessible so that the air supply to
the tool can be shut off in an emergency.
-Check hose and fittings regularly for wear.
-Take care against entanglement of the moving parts of
the tool with clothing, hair, ties, cleaning rags, rings,
jewelry, watches, bracelets, etc. This could cause the
body or parts of the body to be drawn towards and in
contact with the moving parts of the tool and could be
very dangerous.
-It is expected that users will adopt safe working
practices and observe all local, regional and country
legal requirements when installing, using or
maintaining the tool.
-Take care that the exhaust air does not point towards
any other person or material or substance that could
be contaminated by oil droplets. When first lubricating
a tool or if the tool exhaust has a high oil content, do
not allow the exhaust air to come near very hot
surfaces or flames.
-Never lay the tool down until the working attachment
has stopped moving.
-When the tool is not in use, shut off the air supply and
press the
triggerllever to drain the supply line. If the
tool is not to be used for a period of time, first lubricate,
disconnect from air supply and store in a dry average
room temperature environment.
-If the tool is passed from one user to a new or
inexperienced user, make sure these instructions are
passed with the tool.
-
Do not remove any manufacturer fitted safety devices
where fitted,
i.e., wheel guards, safety trigger, speed
governors, etc.
-Wherever possible, secure workpiece with clamps, a
vise, etc. to make it rigid so it does not move during the
work operation. Keep good balance at all times. Do not
stretch or overreach.
-Try to match the tool to the work operation. Do not use
a tool that is too light or heavy for the work operation. If
in doubt, seek advice.
-In general terms, this tool is not suitable for
underwater use or use in explosive environments
-
seek advice from manufacturer.
-Try to make sure that the work area is clear to enable
the work task to be performed safely. If practical and
possible, try to clear unnecessary obstructions before
starting work.
-Always use air hose and couplings with minimum
working pressure ratings at least
1
112 times the
maximum working pressure rating of the tool.
Foreseen Use
Of
The Tool
-
IW38TBP-3PAW38TBP-2Q
The impact wrench is designed for the tightening and loosening of
threaded fasteners within the range as specified by the
manufacturer. It should only be used in conjunction with suitable
impact type nut running sockets. Only use sockets which are of the
impact type.
It is allowed to use suitable extension bars, universal joints and
socket adaptors between the square output drive of the impact
wrench and the square female drive of the socket.
Do not use the tool for any other purpose than that specified
without consulting the manufacturer or the manufacturer's
authorized supplier. To do so may be dangerous.
Never use an impact wrench as a hammer to dislodge or straighten
cross threaded fasteners. Never attempt to modify the tool for other
uses and never modify the tool for even its recommended use as a
nutrunner.
Work Stations
The tool should only be used as a handheld, hand operated tool. It
is always recommended that the tool is used when standing on the
solid floor. It can be used in other positions, but before any such
use, the operator must be in a secure position having a firm grip
and footing and be aware that when loosening fasteners the tool
can move quite quickly away from the fastener being undone. An
allowance must always be made for this
realward movement so as
to avoid the possibility of
handlarmlbody entrapment.
Putting Into Service
Air
Supply
Use a clean lubricated air supply that will give a measured air
pressure at the tool of 90 p.s.i.16.2 bar when the tool is running
with the trigger fully depressed and the air regulator in its
maximum opening flow position. Use recommended hose size and
length. It is recommended that the tool is connected to the air
supply as shown in figure
1. Do not connect a quick connect
coupling directly to the tool, but use a whip or leader hose of
approximately
12 inches length. Do not connect the tool to the air
line system without incorporating an easy to reach and operate air
shut off valve. The air supply should be lubricated. It is strongly
recommended that an air filter, regulator, lubricator (FRL) is used,
as shown in Figure
1,
as this will supply clean, lubricated air at the
correct pressure to the tool. Details of such equipment can be
obtained from your supplier. If such equipment is not used, then
the tool should be lubricated by shutting off the air supply to the
tool, depressurizing the line by pressing the
throt4le lever on the
tool. Disconnect the air line and pour into the hose adaptor (6) a
teaspoonful
(5ml) of a suitable pneumatic motor lubricating oil
preferably incorporating a rust inhibitor. Reconnect tool to air
supply and run tool slowly for a few seconds to allow air to
circulate the oil. If tool is used frequently, lubricate on daily basis
and if tool starts to slow or lose power. When lubricating, also
ensure that the air strainer in hose adaptor (6) is clean.
It is recommended that joint tightness of the threaded fastener
assembly be checked with suitable measuring equipment.
It is recommended that the air pressure at the tool while the tool is
running is 90 p.s.i.16.2 bar.
Operating
The output of the impact wrench in prime working condition is
governed by mainly three factors:
a) the input air pressure;
b) the time the impact wrench is operated on the joint. Normal time
for joints of average tension requirement 3 to 5 seconds;
c) the setting of the air regulator for a given joint at a given pressure
operated for a given time.
The air regulator dial (26) can be used to regulate the output of the
impact wrench if no other means of control is available. It is strongly
recommended that an external pressure regulator, ideally as part of
a
filter/regulator/lubricator
(FRL), is used to control air inlet pressure
so that the pressure can be set to help control the tension required
to be applied to the threaded fastener joint.
There is no consistent, reliable torque adjustment on an impact
wrench of this type. However, the air regulator can be used to adjust
torque to the approximate tightness of a known threaded
joint.To set
the tool to the desired torque, select a nut or screw of known
tightness of the same size, thread pitch and thread condition as those
on the job. Turn air regulator to low position, apply wrench to nut and
gradually increase power (turn regulator to admit more air) until nut
moves slightly in the direction it
wasoriginally set.The tool is now set
to duplicate that tightness, note regulator setting for future
use.When
tightening nuts not requiring critical torque values, run nut up flush
and then tighten an additional one-quarter to one-half turn (slight
additional turning is necessary if gaskets are being clamped). For
additional power needed on disassembly work, turn regulator to its
fully open position. This impact wrench is rated a
318" bolt size.
Rating must be downgraded for spring U bolts, tie bolts, long cap
screws, double depth nuts, badly rusted conditions and spring
fasteners as they absorb much of the impact power. When possible,
clamp or wedge the bolt to prevent springback.
Page No 2
Soak rusted nuts in penetrating oil and break rust seal before
removing with impact wrench. If nut does not start to move in three to
,
five seconds use a larger size impact wrench. Do not use impact
-.
wrench beyond rated capacity as this will drastically reduce tool life.
NOTE: Actual torque on a fastener is directly related to joint
hardness, tool speed, condition of socket and'fhe time the tool is
allowed to impact.
'
Use the simplest possible tool-to-socket hook up. Every connection
absorbs energy and reduces power.
Forwardlreverse operation is controlled by reverse lever (25)
located next to trigger (28). Depress reverse lever (25) to
"C'
position.
The tool is now in reverse mode. Raise reverse lever (25) to
"R"
position.The tool is now in forward position. Ensure that the reverse
valve unit is in the proper position before starting tool.
The regulator dial (26) controls the speed of the
tool and is located
behind the trigger (28). It is a 3-position, thumb operated regulator
with
"3
being the highest setting and "1" the lowest setting. Using
thumb, rotate the dial downwards to increase speed and upwards to
decrease speed.
The tool incorporates an air strainer in hose adaptor (6). Check
periodically to see if this is becoming blocked as blockage will
reduce the speed and power of the
tool.To clean the air strainer it is
necessary to remove the hose adaptor (6) from motor housing (1).
For best results:
1) Always use the correct size impact type socket.
2) Use extra deep sockets in place of extension bars where
possible.
3) Do not use oversized, worn or cracked sockets.
4) Hold the wrench
so
the socket fits squarely on the fastener. Hold
the wrench firmly, but not too tightly, pressing forward slightly.
Dismantling
&
Assembly Instructions
Disconnect tool from air supply.
Heat up connection area of clutch case (56) and motor housing
(l).Then rotate clutch case (56) counter clockwise to remove. Re-
move clutch case assembly from motor housing
(I) then unthread
the flange (42). Gripping spline portion of rotor
(35), remove entire
motor assembly. Dismantle motor assembly by removing front plate
(37) and cylinder (34). Pull pin (4) located behind trigger
(28), then
remove trigger assembly. Dismantle trigger assembly by removing
spring pin
(29), retaining ring (27), screw (24), and E-ring (16).
Remove silencer assembly and hose adaptor (6) by removing pin
(4) located at bottom of motor housing (1). Remove screw (2) and
hanger (3).
For
IW38TBP-3P: Socket ring (60) and O-ring (61) may be pried
off anvil (62) if replacement is needed.
For
IW38TBP-2Q: Stop ring (54), pit washer (53), pit sleeve (52),
pit spring (51) and steel ball (49) may be pried off anvil (48) if
replacement is needed.
Reassembly
Clean all parts and examine for damage and wear. Particularly
examine O-rings and oil seals for cuts and wear. Also carefully
check for cracks and wear on hammer pins
(47), twin hammers
(46), hammer cage (43) and anvil (48) or (62), particularly in the
area of the square drive. Replace all parts where necessary with
manufacturer supplied parts. Lightly coat all parts with a
suitable pneumatic tool lubricating oil and assemble in the reverse
order. Apply Locktite 271 to thread on hose adaptor (6) before
assembly. When installing clutch case assembly use 518 fl. oz. (1
5cc)
of a standard SAE20 grade oil. For IW38TBP-2Q: Put steel ball
(49) into anvil
(48), put pit .spring (51) pit washer (53) and
secure with stop ring (54). Pour in approx. 5
ml of a good quality
lubricating oil, one preferably containing a rust inhibitor, into the
'
hose adaptor (6) with the trigger (28) depressed. Connect to a
suitable air supply and run the tool for a few seconds to allow the
oil to circulate. Check the function of the trigger
(28), reverse lever
(25) and regulator dial (26) and reset for operation required. Refer
to section Operating.
I
Oneration Snecification
I
I
Declaration of Conformity
Sioux Tools Inc.
Air Consumption
Max. Torque Reverse
Max.Torque Forward
Working Torque
Air Inlet Thread
Overall Length:
IW38TBP-3P
-
IW38TBP-2Q
250 Snap-on Drive,
P.O.
Box 1596, Murphy,
NC
28906, U.S.A.
declare under our sole responsibility that the product
2.4 cfm (18 scfm)
-250 ft.lbs. (339 Nm)
230
fi.lbs. (312 Nm)
W200
ft.lbs. (81-271 Nm)
114-18NPT
6.3" (1 60 mm)
Model IW38TBP-3PAW38TBP-2Q Impact Wrenches, Serial Nu,mber
to which this declaration relates is in conformity with the following standard($ or other normative document($
EN792 (Draft), EN292 Parts 1
&
2, IS0 8662 Parts 1
&
7, Pneurop PN8NTC1
foilowing the provisions of
891392lEEC as amended
by
911368lEEC
&
93144lEEC Directives
at 90 PSIG16.2 bar
Mark Pezzoni (President, power and Specialty Tools)
---------------
---------------
---------------
Name and signature or equivalent marking of authorized person
Printed
in Japan
Page
No
3
Modeles IW38TBP-3PAW38TBP-2Q
Tournevis
a
percussion
Instructions de fonctionnement
Comprend
:
Utilisation prevue, stations de travail, mise en
service, fonctionnement, demontage, montage et regles de
skurite.
Fabricant/Fournisseur
Sioux Tools, Inc.
250 Snap-on Drive
P.O. Box 1596
Murphy, NC 28906
U.S.A.
Tel No. 828-835-9765 Fax No. 828-835-9685
Important
Lisez attentivement ces instructions avant d'installer, de faire
fonctionner. d'entretenir ou de h~arer cet outil. Gardez ces
~ ~
instruction; dans un endroit sQr ifacilement accessible.
Type de produit
Tournevis
a
percussion
'Numero du modele
IW38TBP3P
(318"
Goupille)
IW38TBP-2Q
(114"
QCC)
Tours par
minutes rnax
urnin
7-000
Numero de serie
Poids net du produit
Pression d'air
De fonctionnement
recommandee
6,2
bar
Maximum
6,2
bar
CE
Emploi conseille d'un
dispositif d'equilibrage ou
IW38TBP-3P
0,95
kgs
IW38TBP-2Q
0,97
kgs
Alesage
de
tuyau recommande
Longueur maximum de
d'un support,
NON
Taille minimum
1
tuyau recommandee
Niveau de puissance sonore 95,O dB (A)
-
10
mm
Methode de test:
Teste selon Ie code de test
Pneurop
PN8NTC1 et la norme IS0 3744.
10
m
Niveau sonore:
Niveau de pression sonore
84,O dB
(A)
Regles de securite pour utiliser le
tournevis
a
percussion IW38TBP-3Pl
IW38TBP-2Q
Ernployez seulernent des douilles, rallonges, cardans,
etc. pour cle a choc qui respondent aux conditions
norninales de fonctionnernent de la cle a chocs.
Une exposition prolongee aux vibrations peut causer des
blessures.
Lisez les instructions avant d'ernployer cet outil. Tous le
operateurs doivent connaitre parfaiternent son utilisation
et
connaitre ces regles de securite.
Ne depassez pas la pression d'air de fonctionnernent
maximum.
Ernployez I'equipernent de protection personnelle
recornrnande.
Certaines poussieres engendrees par le ponGage, le
sciage, le rneulage, le perGage
Messages de securite
Eqqoipementde
dcun'te personnelle
Lunettes de securite OUI
Gants de securite
Bottes de securite
Masques
Protecteurs auriculaires OUI
I
Si I'outil doit 6tre employe avec un dispositif d'equilibrage
ou de suspension, assurez-vousque I'outil est bienfixe ace
systerne
desuspension ou de support.
Quand vous ernployez I'outil, tenez toujours le corps et les
mains
a
I'ecart des accessoires de travail fixes a I'outil.
Cet outil n'est pas isole electriquernent. N'employez
jarnais cet outil si vous risquez d'entrer en contact avec de
I'electricite.
Quand vous ernployez cetoutil, prenez une position ferrne
et tenez bien I'outil pour cornpenser toutes forces de
reaction qui pourraient
6tre causees par le fonctionnernent
de I'outil. Ne serrez pas trop fort dans les mains.
Ernployez seulernent des pieces de rechange correctes
pour I'entretien et les reparations. N'irnprovisez pas de
reparations ternporaires. L'entretien et les reparations ne
doivent
6tre effectuees que par du personnel qualifie.
Ne bloquez pas les valves "On10ff" en position dans la
pneumatique et d'autres activites de
construction contiennent des produits
chirniques qui sont
connus cornrne
provoquant
le cancer, des anomalies
congenitales et d'autres troubles
reproductifs.
Ernployez seulernent de I'air cornprime
dans les conditions recornrnandees.
Si I'outil sernble ma1 fonctionner, arrktez
irnrnediaternent son ernploi et faites-le
reparer. S'il est difficile d'enlever I'outil de
son aire de
service, dtez I'arrivee d'air
et
fixez une note d'avertissernent rnanuscrite
a
I'outil.
A
MlSE EN GARDE
Lisez toujours les instructions
avant d'ernployer des
outils
a
6ktriques
Portez
toulours
des
lunettes
de
@
s6curite
'
@
Portez toujours des dispositifs
de protection antibruit
A
cvfiez I'exposition prolongee
aux vibrations
Page No
4
Niveau de vibrations
Moins de 2,5
m/s2
Methode de test:
teste selon les normes IS0
8662, sections 1
&
7
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Sioux Tools IW38TB P-3P Operator Instructions Manual

Catégorie
Outils électroportatifs
Taper
Operator Instructions Manual
Ce manuel convient également à

dans d''autres langues