BC-QM1
4-467-217-03(1)
Battery Charger
Chargeur de Batterie
Operating Instructions
Mode d’emploi
© 2013 Sony Corporation Printed in China
USB
ˎ
NP-FH50 NP-FV50 NP-FV70
NP-FV100
70 80 125 230
NP-FW50
NP-FM500H
NP-FM50
NP-QM71D NP-QM91D
115 160 140 225 330
25
ˎ
ˎ
100V-240V
1
CHARGE 2
1.5
0.15
CHARGE
CHARGE
CHARGE
10 30
CHARGE
1 CHARGE
1
ˎ
ˎ
USB
ˎ
ˎ
ˎ
USB
AC100V 240V 50Hz/60Hz 0.38 A
DC8.4 V 1,600 mA BATTERY CHARGE
DC5.0 V 1,500 mA USB POWER 5V 1500mA
0 40
20 +60
67 49 105
175 g
BC-QM1 ............. 1
ˎ
ˎ
1
ˎ
BC-QM1
ˎ
ˎ
ˎ
USB
V /H /P
ˎ
/W /M
InfoLITHIUM
ˎ
ˎ
V H P
ˎ
W M
1
2 CHARGE
3
4 USB
5
6
M
7
V/H/P
8
W
9
M/V/H/P
10 W
11
USB
12
USB
1
InfoLITHIUM V/H/P M
InfoLITHIUM W
W
2
CHARGE
90 CHARGE
ˎ
ˎ
ˎ
InfoLITHIUM V/H/P M
InfoLITHIUM W
CHARGE
- 30%
30% - 60%
60% - 90%
90% -
NP-FH50 NP-FV50 NP-FV70
NP-FV100
170 195 400 750
NP-FW50 NP-FM500H
NP-FM50 NP-QM71D NP-QM91D
145 270 205 395 620
25
ˎ
ˎ
CHARGE
ˎ
CHARGE
ˎ
1
ˎ
USB
1
2
3
USB
ˎ
USB AC
ˎ
USB
USB
USB
ˎ
USB
USB USB
ˎ
USB
ˎ
USB
ˎ
USB
ˎ
ˎ
USB
ˎ
USB USB
ˎ
USB
USB USB
ˎ
Thank you for purchasing the Sony Battery charger.
Before operating this Battery charger, please read this manual thoroughly
and retain it for future reference.
Features
The BC-QM1 Battery Charger can be used as follows.
This unit can charge or power Sony devices (video cameras etc.) using a
ˎ
USB cable compatible with your device. (USB AC adaptor function)
This unit can be used as a charger for Sony “InfoLITHIUM” battery
ˎ
packs (V series/H series/P series/W series/M series). (Battery charger
function)
Operation mode of this unit
The USB AC adaptor function and battery charger function can be used
ˎ
at the same time. (Simultaneous charge mode)
You can make this unit charge a battery pack quicker than usual by
ˎ
pressing the quick charge button. (Quick charge mode)
Operation
mode
Battery
charging
USB output Quick charge
button
Simultaneous
charge mode
Normal
charging
Enabled Off
Quick charge
mode
Quick charging Disabled On
“InfoLITHIUM” battery packs (V series/H series/P series/W
ˎ
series/M series) have the
/ / /
/ mark.
“InfoLITHIUM” is a trademark of Sony Corporation.
ˎ
This unit cannot be used to charge a nickel cadmium battery pack or
ˎ
nickel metal hydride battery pack.
This unit can be only be used to charge “InfoLITHIUM” battery
ˎ
packs (V series/H series/P series/W series/M series).
Identifying the parts
Charging status indicator lamp1
CHARGE lamp2
Quick charge button3
USB connector4
Power plug5
Battery terminal (for M series)6
Battery terminal (for V/H/P 7
series)
Battery terminal (for W series)8
9 mark (for M/V/H/P series)
10 mark (for W series)
USB rechargeable device (Video 11
camera, etc.)
USB cable compatible with your 12
device
To Charge the Battery Pack
The battery pack is charged by attaching it to this unit.
1 Attach the battery pack.
InfoLITHIUM V/H/P series (See illustration )
InfoLITHIUM M series (See illustration )
Align the mark on the battery pack in the direction of the
mark on this unit and insert it.
Slide the battery pack in the direction illustrated.
InfoLITHIUM W series (See illustration )
Align the mark on the battery pack in the direction of the
mark on this unit, and bring the battery pack into contact with
the battery terminal (for W series) of this unit.
Press the battery pack in the direction illustrated until it is flat
inside this unit.
2 Lift the power plug and connect it to a wall outlet (wall
socket).
Always connect the power plug with the prongs at the top. (See
illustration )
Do not connect the power plug with the prongs at the bottom. (See
illustration )
The CHARGE lamp (orange) lights up and charging begins.
The CHARGE lamp goes out when the battery pack is about 90 %
charged.
The charging status indicator lamp goes out when charging is
completed. (Full charge)
Notes
Do not lift this unit by the battery pack.
ˎ
Be careful not to hit the battery pack against this unit.
ˎ
Be careful not to catch your fingers when attaching and removing
ˎ
the battery pack.
To remove the battery pack
InfoLITHIUM V/H/P series
InfoLITHIUM M series
Remove the battery pack by sliding it in the opposite direction to when
you attached it.
InfoLITHIUM W series
Lift the battery pack up and remove it.
You can check the approximate charging status with the charging status
indicator lamp.
, ... Off, , ... Lit up
Charging status
indicator lamp
CHARGE lamp
Immediately after
attaching the battery
pack - 30 %
30 % - 60 %
60 % - 90 %
90 % - Full charge
Full charge
completed
The charge level shown by the charging status indicator lamp and the
percentages in the above table are rough guides.
The actual status may differ depending on the ambient temperature or the
condition of the battery pack.
2
1
(Suite à la page arrière)
BC-QM1
USB
ˎ
USB AC
V /H /
ˎ
P /W /M
USB AC
ˎ
ˎ
Charging time
The following table shows the charging time for a battery pack that is
completely discharged.
Battery pack
NP-FH50 NP-FV50 NP-FV70 NP-FV100
Full charge
time
170 195 400 750
Battery pack
NP-FW50 NP-FM500H NP-FM50 NP-QM71D NP-QM91D
Full charge
time
145 270 205 395 620
Approximate number of minutes to charge an empty battery pack.
ˎ
For more about the battery life, see the instruction manual of your
ˎ
device.
The charging time may differ depending on the condition of the battery
ˎ
pack or the ambient temperature.
The times shown are for charging an empty battery pack which has
ˎ
been run down with a device, using this unit at an ambient temperature
of 25 °C (77 °F).
Charging temperature
The temperature range for charging is 0 °C to 40 °C (32 °F to 104 °F).
For maximum battery efficiency, the recommended temperature
range when charging is 10 °C to 30 °C (50 °F to 86 °F).
Notes
If the CHARGE lamp does not light up, check if the battery pack is
ˎ
firmly attached to this unit.
When a fully charged battery pack is installed, the CHARGE lamp
ˎ
lights up once and then goes out.
A battery pack that has not been used for a long time may take longer
ˎ
than usual to charge.
Use this unit with the USB cable (See
illustration )
1 Connect your device to this unit.
2 Lift the power plug up and connect it to a wall outlet (wall
socket).
Powering starts automatically.
Powering does not start if the quick charge button is lit. Press the
quick charge button to turn it off before using this unit.
3 After the device is completely recharged, unplug this unit
and disconnect the device from this unit.
Notes
A USB cable is not supplied with this unit. Prepare a USB cable
ˎ
compatible with your device.
You may need to perform some operation on your device to use the
ˎ
USB AC adaptor function of this unit. The operation and specifications
differ depending on your device model. For details, refer to the
instruction manuals of your device.
Connecting this unit to a device via
USB cable while still charging the
battery pack (Simultaneous charge
mode)
This unit can charge a battery pack and power a device connected via
USB cable at the same time.
For details on attaching a battery pack to this unit, see “To Charge the
Battery Pack.”
For details on connecting to a device, see “Use this unit with the USB
cable.”
Charging in a shorter time (Quick
charge mode)
During battery pack charging, press the quick charge button to charge in
a shorter time.
The quick charge button lights up orange during quick charge mode.
Notes
“Simultaneous charge mode” and “Quick charge mode” cannot be used
ˎ
at the same time.
When quick charge is started, powering to a device connected via USB
cable stops.
Always check the status of your device before use.
When quick charge is completed, powering to the device connected via
USB cable restarts.
This unit will not switch to quick charge mode if no battery pack is
ˎ
attached. Always attach a battery pack to this unit before operating the
quick charge button.
Charging time in quick charge mode
Battery pack
NP-FH50 NP-FV50 NP-FV70 NP-FV100
Full charge
time
70 80 125 230
Battery pack
NP-FW50 NP-FM500H NP-FM50 NP-QM71D NP-QM91D
Full charge
time
115 160 140 225 330
Approximate number of minutes to charge an empty battery pack.
ˎ
The charging time may differ depending on the condition of the battery
ˎ
pack or the ambient temperature.
The times shown are for charging an empty battery pack which has
ˎ
been run down with a device, using this unit at an ambient temperature
of 25 °C (77 °F).
This unit supports worldwide voltages 100 V to 240 V.
Do not use an electronic voltage transformer, as this may cause a
malfunction.
The shape of wall outlets (wall sockets) differs depending on the
country and region. Check before departure.
Troubleshooting
When the CHARGE lamp blinks, check through the following chart.
The CHARGE lamp blinks in two ways.
Blinks slowly: Turns on and off repeatedly every 1.5 seconds
Blinks quickly: Turns on and off repeatedly every 0.15 seconds
The action to be taken depends on the way the CHARGE lamp blinks.
When the CHARGE lamp keeps blinking slowly
Charging is pausing. This unit is in the standby state.
If the room temperature is out of the appropriate temperature range,
charging stops automatically.
When the room temperature returns to the appropriate range, the
CHARGE lamp lights up and charging restarts.
We recommend charging the battery pack at 10 °C to 30 °C (50 °F to
86 °F).
When the CHARGE lamp keeps blinking quickly
When charging the battery pack for the first time in one of the
following situations, the CHARGE lamp may blink quickly.
If this happens, remove the battery pack from this unit, reattach it and
charge it again.
When the battery pack is left for a long time
When the battery pack is left installed in the camera for a long time
Immediately after purchase
If the CHARGE lamp keeps blinking quickly, check through the following
chart.
Please contact your nearest Sony dealer in connection with the product that may
have a problem.
Remove the battery pack that is being charged and then rmly attach the same
battery pack again.
The CHARGE lamp blinks again:
Install another battery pack.
The CHARGE lamp lights up and
does not blink again:
If the CHARGE lamp goes out
because the charging time has
passed, there is no problem.
The CHARGE lamp blinks again:
e problem is with this unit.
The CHARGE lamp lights up and
does not blink again:
If the CHARGE lamp goes out
because the charging time has
passed, the problem is with the
battery pack rst installed.
The battery pack cannot be charged.
This unit is not connected to the wall outlet (wall socket).
ˎ
Connect this unit to the wall outlet (wall socket) properly.
The battery pack is not firmly attached.
ˎ
Attach the battery pack to this unit correctly.
The device connected by the USB cable does not work.
This unit is not connected to the wall outlet (wall socket).
ˎ
Connect this unit to the wall outlet (wall socket) properly.
The device connected to this unit may need to be operated.
ˎ
Refer to the instruction manual of the connected device.
This unit is set to quick charge mode.
ˎ
When this unit is set to quick charge mode, powering the device
connected with a USB cable is stopped.
Operate the quick charge button and check that its light is off.
Specications
Input rating 100 V - 240 V AC 50 Hz/60 Hz
0.38 A
Output rating 8.4 V DC 1,600 mA (BATTERY CHARGE)
5.0 V DC 1,500 mA (USB POWER 5V 1500mA)
Operating temperature 0 °C to 40 °C (32 °F to 104 °F)
Storage temperature –20 °C to +60 °C (–4 °F to +140 °F)
Dimensions (Approx.) 67 mm × 49 mm × 105 mm (w/h/d)
(2 3/4 in. × 1 15/16 in. × 4 1/4 in.)
Mass Approx. 175 g (6.2 oz)
Included items Battery Charger (BC-QM1) (1)
Set of printed documentation
Design and specifications are subject to change without notice.
Battery to be recharged for this product is follows
Brand Name Sony
Battery Type
NP-FV30 NP-FV50 NP-FV70 NP-FV100 NP-FH50
NP-FW50
NP-FM500H
NP-FM50 NP-QM71D NP-QM91D
Precautions on Use
The USB connector of this unit is for output only. Do not connect it to
ˎ
the USB port of a computer, etc. Doing so may cause a malfunction.
Some USB rechargeable devices cannot be used with this unit. Also,
ˎ
some devices may not be operable while recharging. Check the charging
specifications in the instruction manual of your device.
When you use the USB connector of this unit, attach a battery pack to
ˎ
the connected device. Not doing so may cause data loss from the device
or damage due to the device crashing.
Be warned that some devices may suddenly lose their input memory
ˎ
regardless of whether they are used with the USB connector of this unit.
(For details, refer to the instruction manual supplied with your device.)
Always back up the input memory beforehand. Sony is not liable for
any loss of input memory when using this unit.
Make sure before using this unit that its current and voltage match
ˎ
those of the outlet.
Depending on the conditions of use of this unit’s USB connector, this
ˎ
unit may automatically shut down for safety reasons if the input current
is too high.
Sony does not guarantee operation of this unit if you use it with a USB
ˎ
hub or USB extension cable. Always follow the designated connecting
method of the USB cable supplied with your device.
When not using this unit, disconnect the USB cable from its USB
ˎ
connector and store it.
Merci pour l’achat de ce chargeur de batterie Sony.
Avant d’utiliser ce chargeur de batterie, veuillez lire attentivement ce
manuel et le conserver pour toute référence future.
Caractéristiques
Le chargeur de batterie BC-QM1 peut être utilisé de la façon
suivante.
Cet accessoire peut charger ou alimenter les appareils Sony
ˎ
(caméscopes, etc.) utilisant un câble USB compatible avec votre
appareil. (Fonction Adaptateur secteur-USB)
Cet accessoire peut être utilisé comme chargeur pour les batteries
ˎ
InfoLITHIUM Sony (série V/série H/série P/série W/série M).
(Fonction Chargeur de batterie)
Mode de fonctionnement de cet accessoire
La fonction Adaptateur secteur-USB et la fonction Chargeur de batterie
ˎ
peuvent être utilisées en même temps. (Mode de charge simultanée)
En appuyant sur le bouton de charge rapide de cet accessoire, vous
ˎ
pourrez obtenir une charge de la batterie plus rapide qu’à l’ordinaire.
(Mode de charge rapide)
Mode de
fonctionnement
Charge de la
batterie
Sortie USB Quick charge
button
Mode de charge
simultanée
Charge
normale
Activée Désactivée
Mode de charge
rapide
Charge rapide Désactivée Activée
Les batteries « InfoLITHIUM » (série V/série H/série P/série W/série
ˎ
M) portent la marque
/ / / /
.
« InfoLITHIUM » est une marque commerciale de Sony
ˎ
Corporation.
Cet accessoire ne peut pas être utilisé pour charger une batterie au
ˎ
nickel-cadmium ou une batterie au nickel-hydrure métallique.
Cet accessoire ne peut être utilisé que pour charger les batteries
ˎ
« InfoLITHIUM » (série V/série H/série P/série W/série M).
Identication des éléments
Témoin d’état de charge1
Témoin CHARGE2
Bouton de charge rapide3
Connecteur USB4
Fiche d’alimentation5
Borne de batterie (pour la série 6
M)
Borne de batterie (pour la série 7
V/H/P)
Borne de batterie (pour la série 8
W)
Repère 9 (pour la série
M/V/H/P)
Repère 10 (pour la série W)
Appareil rechargeable par l’USB 11
(Caméscope, etc.)
Câble USB compatible avec votre 12
appareil
Pour charger la batterie
La batterie rechargeable se charge lorsqu’elle est insérée dans cet appareil.
1 Insérez la batterie.
Série InfoLITHIUM V/H/P (Voir l’illustration )
Série InfoLITHIUM M (Voir l’illustration )
Alignez le repère sur la batterie dans le sens du repère sur cet
accessoire et insérez la batterie.
Faites glisser la batterie dans le sens indiqué.
Série InfoLITHIUM W (Voir l’illustration )
Alignez le repère sur la batterie dans le sens du repère sur cet
accessoire et mettez la batterie en contact avec la borne de batterie
(pour la série W) de cet accessoire.
Appuyez sur la batterie dans le sens indiqué jusqu’à ce qu’elle soit à
plat dans cet accessoire.
2 Relevez la fiche d’alimentation et branchez-la sur une prise
murale.
Raccordez toujours la fiche d’alimentation avec les broches orientées
vers le haut (Voir l’illustration ).
Ne raccordez pas la fiche d’alimentation avec les broches orientées vers
le bas (Voir l’illustration ).
Le témoin CHARGE (orange) s’allume et la recharge commence.
Le témoin CHARGE s’éteint lorsque la batterie est chargée à environ
90 %.
Le témoin d’état de charge s’éteint quand la charge est terminée.
(Charge complète)
Remarques
Ne soulevez pas cet accessoire par la batterie.
ˎ
Veillez tout particulièrement à ne pas cogner la batterie contre cet
ˎ
accessoire.
Faites attention à ne pas vous pincer les doigts lorsque vous insérez
ˎ
ou retirez la batterie.