Weber 61012001 Manuel utilisateur

E330 • SE330 • CE330

Keep this Owner’s Manual for future reference, thoroughly read through it, and

if you have any questions please contact us today.

LP Owner’s Manual

54188

062218

enUS  esMX  frCA

Download the Weber Grills App!

Onboard with the free Weber Grills App. The Weber app is your answer to everything

grilling and will lead you through everything from gas tank installation to your ﬁrst grill

out. Customize the app to your exact model, and taste, by registering your grill with a

few simple questions.

• Grill setup and gas tank installation

• Grilling techniques and guides

• Timers and tools

• Recipes for any taste

• Seasonal menus/recipes

2

Installation and Assembly

m DANGER: This grill is not intended to be installed in

or on recreational vehicles or boats.

m WARNING: Do not use this grill unless all parts

are in place and the grill was properly assembled

according to the assembly instructions.

m WARNING: Do not build this model of grill in any

built-in or slide-in construction.

m WARNING: Do not modify the appliance (grill). Liquid

propane gas is not natural gas. The conversion or

attempted use of natural gas in a liquid propane gas

unit or liquid propane gas in a natural gas unit is

unsafe and will void your warranty.

• In the United States, installation must conform with

local codes or, in the absence of local codes, with

either the National Fuel Gas Code, ANSI Z223.1/

NFPA 54, Natural Gas and Propane Installation Code,

CSA B149.1; or Propane Storage and Handling Code,

B149.2; or the Standard for Recreational Vehicles,

ANSI A119.2/NFPA 1192, and CSA Z240 RV Series,

Recreational Vehicle Code, as applicable.

• InCanada, the installation of this grill must comply

with local codes and/or the latest edition of Standard

CAN/CSA-B149.2 (Propane Storage and Handling

Code). These instructions, while generally acceptable,

do not necessarily comply with the Canadian

installation codes, particularly with piping above and

below ground.

• In Mexico, if there are local codes that apply to

portable gas appliances, you must comply with the

latest edition of Ocial Mexican Standard (NOM).

• If an external electrical source is utilized (such as

a rotisserie) it must be electrically grounded in

accordance with local codes or, in the absence of local

codes, with the National Electrical Code, ANSI/NFPA

70, or the Canadian Electrical Code, Part 1, CSA C22.1.

Operation

m DANGER: Only use the grill outdoors in a well-

ventilated area. Do not use in a garage, building,

breezeway, tent, any other enclosed area, or

beneath overhead combustibleconstruction.

m DANGER: Do not use the grill in any vehicle or in any

storage or cargo area of any vehicle. This includes,

but is not limited to, cars, trucks, station wagons,

mini-vans, sport utility vehicles, recreational

vehicles, andboats.

m DANGER: Do not use the grill within 24 inches (61

cm) of combustible materials. This includes the top,

bottom, back and sides of the grill.

m DANGER: Keep the cooking area clear of ﬂammable

vapors and liquids such as gasoline, alcohol, etc.,

and combustible materials.

m DANGER: This appliance (grill) must be kept away

from ﬂammable materials during use.

m DANGER: Do not put a grill cover or anything

ﬂammable on, or in the storage area under the grill

while it is in operation or is hot.

m DANGER: Should a grease ﬁre occur, turn o all

burners and leave lid closed until ﬁre is out.

m WARNING: Accessible parts may be very hot.

Keepyoung children away.

m WARNING: The use of alcohol, prescription drugs,

non-prescription drugs, or illegal drugs may impair

the consumer’s ability to properly and safely

assemble, move, store, or operate thegrill.

m WARNING: Never leave the grill unattended during

pre-heating or use. Exercise caution when using

this grill. The entire cookbox gets hot when in use.

m WARNING: Do not move the appliance (grill)

duringuse.

m WARNING: Keep any electrical supply cord and the

fuel supply hose away from any heated surfaces.

m CAUTION: This product has been safety-tested and

is only certiﬁed for use in a speciﬁc country. Refer

to country designation located on outside of box.

• Do not use charcoal or lava rock in the grill.

Storage and/or Nonuse

m WARNING: Turn o the gas supply at the gas

cylinder (tank) after use.

m WARNING: LP tanks must be stored outdoors out of

the reach of children and must not be stored in a

building, garage, or any other enclosed space.

m WARNING: After a period of storage and/or nonuse,

the grill should be checked for gas leaks and burner

obstructions before use.

m Storage of the grill indoors is permissible only if the

LP tank is disconnected and removed from the grill.

California Proposition 65

m WARNING: Combustion byproducts produced when

using this product contain chemicals known to the

state of California to cause cancer, birth defects, or

other reproductive harm.

m PROPOSITION 65 WARNING: Handling the brass

material on this product exposes you to lead, a

chemical known to the state of California to cause

cancer, birth defects, or other reproductive harm.

Wash hands after handling this product.

m DANGER

If you smell gas:

• Shut o gas to the appliance

(grill).

• Extinguish any open ﬂame.

• Open lid.

• If odor continues, keep away

from the appliance (grill)

and immediately call your

gas supplier or your ﬁre

department.

m WARNING

• Do not store or use gasoline

or other ﬂammable liquids

or vapors in the vicinity

of this (grill) or any other

appliance.

• An LP cylinder (tank) not

connected for use shall

not be stored in the vicinity

of this (grill) or any other

appliance.

USE OUTDOORS ONLY.

READ THE INSTRUCTIONS BEFORE USING

THE APPLIANCE (GRILL).

NOTICE TO INSTALLER: These instructions

must be left with the consumer.

NOTICE TO CONSUMER: Retain these

instructions for future reference.

Important

SafetyInformation

DANGER, WARNING, and CAUTION

statements are used throughout this

Owner's Manual to emphasize critical and

important information. Read and follow

these statements to help ensure safety and

prevent property damage. Thestatements

are deﬁned below.

m DANGER: Indicates a hazardous

situation which, if not avoided,

will result in death or seriousinjury.

m WARNING: Indicates a hazardous

situation which, if not avoided,

could result in death or seriousinjury.

m CAUTION: Indicates a hazardous

situation which, if not avoided,

could result in minor or moderateinjury.

Welcome to Weber

3

Welcome to Weber

The grills illustrated in this Owner’s Manual may vary

slightly from the model purchased.

45

frCA

23

esMX

TABLE OF CONTENTS

2 Welcome to Weber

Important SafetyInformation

4 The Weber Promise

Warranty

5 Product Features

GENESIS II Features

The GS4 GrillingSystem

6 Tips and Hints

The Flame - Direct or Indirect

Grilling Do's and Don'ts

8 Getting Started

Important Information about LPGas

& Gas Connections

LP Tank Installation & LeakChecking

Reﬁlling or Replacing an LPTank

12 Operation

The Very First Time You Grill

Every Time You Grill

Igniting the Grill

Igniting the Side Burner

16 Product Care

Cleaning and Maintenance

18 Troubleshooting

21 Grilling Guide

66 Replacement Parts

Hello and welcome to

the Weber Family!

Please be sure to read this Owner’s Manual and download the

free Weber Grills app so that you’re up and grilling as quickly

as possible. The Weber Grills app is your answer to everything

grilling. From gas tank installation to recipes and customizable

features, this app is where you’ll start your grilling journey and

never look back.

Thank you for choosing Weber!

4

The Weber Promise

PROTECT

YOUR

INVESTMENT

Shield your grill from the

elements with a heavy-duty

premiumgrillcover.

Warranty

Thank you for purchasing a WEBER product. Weber-

Stephen Products LLC, 1415 S. Roselle Road, Palatine,

Illinois 60067 and its Americas Business units

(“WEBER”) pride ourselves on delivering a safe, durable,

and reliable product.

This is WEBER’s Voluntary Warranty provided to you

at no extra charge. It contains the information you will

need to have your WEBER product repaired or replaced

in the unlikely event of a failure or defect.

Pursuant to applicable laws, the Owner has several

rights in case the product is defective. Those rights

include supplementary performance or replacement,

abatement of the purchasing price, and compensation.

These and other statutory rights remain unaected by

this Warranty provision. In fact, this Warranty grants

additional rights to the Owner that are independent

from statutory Warranty provisions.

WEBER’s Voluntary Warranty

WEBER warrants, to the purchaser of the WEBER

product (or in the case of a gift or promotional situation,

the person for whom it was purchased as a gift or

promotional item) (“Owner”), that the WEBER product is

free from defects in material and workmanship for ten

(10) years from the date of purchase when assembled

and operated in accordance with the accompanying

Owner’s Manual, normal wear and tear excluded. (Note:

If you lose or misplace your WEBER Owner’s Manual,

a replacement is available online at www.weber.com.)

WEBER agrees within the framework of this warranty

to repair or replace the part that is defective in

material or workmanship subject to the limitations, and

exclusions listed below. TO THE EXTENT ALLOWABLE

BY APPLICABLE LAW, THIS WARRANTY IS EXTENDED

ONLY TO THE ORIGINAL PURCHASER AND IS NOT

TRANSFERABLE TO SUBSEQUENT OWNERS, EXCEPT

IN THE CASE OF GIFTS AND PROMOTIONAL ITEMS AS

NOTED ABOVE.

WEBER stands by its products and is happy to provide

you with the Warranty described for material defects in

the grill or its relevant components, normal wear and

tear excepted.

• ‘Normal wear and tear’ includes cosmetic and

other immaterial deterioration that may come with

ownership of your grill over time, such as surface rust,

dents / scratches, etc.

However, WEBER will honor this Warranty for the grill or

its relevant components where damage or dysfunction

results from a material defect.

• ‘Material defect’ includes rust through or burn through

of certain parts, or other damage or failure inhibiting

your ability to safely / properly use your grill.

Owner’s Responsibilities Under this

Warranty / Exclusion of Warranty

To ensure trouble-free Warranty coverage, it is

important (but not required) that you register your

WEBER product online at www.weber.com. Please

also retain your original sales receipt and/or invoice.

Registering your WEBER product conﬁrms your

warranty coverage, will expedite any Warranty claims

you may need to make, and provides a direct link

between you and WEBER in case we need to contact

you. If you have not had time to register your grill before

calling for Warranty service, please have the following

information available when you do call:

Name – Address – Phone Number – Email – Serial

Number – Purchase Date – Purchase Dealer – Model –

Color – Primary Issue

The above warranty only applies if the Owner takes

reasonable care of the WEBER product by following

all assembly instructions, usage instructions,

and preventative maintenance as outlined in the

accompanying Owner’s Manual, unless the Owner can

prove that the defect or failure is independent of non-

compliance with the above mentioned obligations. If

you live in a coastal area, or have your product located

near a pool, maintenance includes regular washing

and rinsing of the exterior surfaces as outlined in the

accompanying Owner’s Manual.

This WARRANTY lapses if there are damages,

deteriorations, discolorations, and/or rust for which

WEBER is not responsible caused by:

• Abuse, misuse, alteration, modiﬁcation, misapplication,

vandalism, neglect, improper assembly or installation,

and failure to properly perform normal and routine

maintenance;

• Insects (such as spiders) and rodents (such as

squirrels), including but not limited to damage to

burners and/or gas hoses;

• Exposure to salt air and/or chlorine sources such as

swimming pools and hot tubs/spas;

• Severe weather conditions such as hail, hurricanes,

earthquakes, tsunamis or surges, tornadoes or severe

storms.

• Acid rain and other environmental factors

The use and/or installation of parts on your WEBER

product that are not genuine WEBER parts will void this

Warranty, and any damages that result hereby are not

covered by this Warranty. Any conversion of a gas grill

not authorized by WEBER and performed by a WEBER

authorized service technician will void this Warranty.

Warranty Processing

If you believe that you have a part which is covered by

this Warranty, please contact WEBER Customer Service

using the contact information on our website (www.

weber.com). WEBER will, upon investigation, repair or

replace (at its option) a defective part that is covered by

this Warranty. In the event that repair or replacement

are not possible, WEBER may choose (at its option) to

replace the grill in question with a new grill of equal or

greater value. WEBER may ask you to return parts for

inspection, shipping charges to be pre-paid by Owner.

When you contact Customer Service, please have the

following information available:

Name – Address – Phone Number – Email – Serial

Number – Purchase Date – Purchase Dealer – Model –

Color – Primary Issue

Disclaimers

APART FROM THE WARRANTY AND DISCLAIMERS

AS DESCRIBED IN THIS WARRANTY STATEMENT,

THERE ARE EXPLICITLY NO FURTHER WARRANTY

OR VOLUNTARY DECLARATIONS OF LIABILITY GIVEN

HERE WHICH GO BEYOND THE STATUTORY LIABILITY

APPLYING TO WEBER. THE PRESENT WARRANTY

STATEMENT ALSO DOES NOT LIMIT OR EXCLUDE

SITUATIONS OR CLAIMS WHERE WEBER HAS

MANDATORY LIABILITY AS PRESCRIBED BY STATUTE.

NO WARRANTIES SHALL APPLY AFTER THE TEN

(10) YEAR PERIOD OF THIS WARRANTY. NO OTHER

WARRANTIES GIVEN BY ANY PERSON, INCLUDING

A DEALER OR RETAILER, WITH RESPECT TO ANY

PRODUCT (SUCH AS ANY “EXTENDED WARRANTIES”),

SHALL BIND WEBER. THE EXCLUSIVE REMEDY OF THIS

WARRANTY IS REPAIR OR REPLACEMENT OF THE PART

OR PRODUCT.

IN NO EVENT UNDER THIS VOLUNTARY WARRANTY

SHALL RECOVERY OF ANY KIND BE GREATER THAN

THE AMOUNT OF THE PURCHASE PRICE OF THE

WEBER PRODUCT SOLD.

YOU ASSUME THE RISK AND LIABILITY FOR LOSS,

DAMAGE, OR INJURY TO YOU AND YOUR PROPERTY

AND/OR TO OTHERS AND THEIR PROPERTY ARISING

OUT OF THE MISUSE OR ABUSE OF THE PRODUCT OR

FAILURE TO FOLLOW INSTRUCTIONS PROVIDED BY

WEBER IN THE ACCOMPANYING OWNER’S MANUAL.

PARTS AND ACCESSORIES REPLACED UNDER THIS

WARRANTY ARE WARRANTED ONLY FOR THE BALANCE

OF THE ABOVE MENTIONED ORIGINAL TEN (10) YEAR

WARRANTY PERIOD.

THIS WARRANTY APPLIES TO PRIVATE SINGLE FAMILY

HOME OR APARTMENT USE ONLY AND DOES NOT

APPLY TO WEBER GRILLS USED IN COMMERCIAL,

COMMUNAL OR MULTI-UNIT SETTINGS SUCH AS

RESTAURANTS, HOTELS, RESORTS, OR RENTAL

PROPERTIES.

WEBER MAY FROM TIME TO TIME CHANGE THE DESIGN

OF ITS PRODUCTS. NOTHING CONTAINED IN THIS

WARRANTY SHALL BE CONSTRUED AS OBLIGATING

WEBER TO INCORPORATE SUCH DESIGN CHANGES

INTO PREVIOUSLY MANUFACTURED PRODUCTS,

NOR SHALL SUCH CHANGES BE CONSTRUED AS

AN ADMISSION THAT PREVIOUS DESIGNS WERE

DEFECTIVE.

Weber-Stephen Products LLC

Customer Service Center

1415 S. Roselle Road

Palatine, IL 60067

U.S.A.

For replacement parts, call:

1-800-446-1071

The WEBER Promise

At WEBER, we pride ourselves on two things: making grills that last and

providing a lifetime of excellent customer service.

5

Product Features

GENESIS II

FEATURES

A Built-In Thermometer

Being aware of the temperature inside of your grill

allows you to adjust the heat when needed.

B TUCKAWAY Warming Rack

Keeps food warm, or toasts buns, while the main

course ﬁnishes grilling on the grate. Fold it down when

not in use for easy storage.

C Porcelain-Enameled,

Cast Iron Cooking Grates

Porcelain-enameled, cast-iron cooking grates provide

even heat distribution across the entire grilling surface

and superior heat retention.

(SE-330 equipped with stainless steel grates.)

D Side Tables with Integrated Tool Hooks

Use the side tables to keep platters, seasonings, and

tools within arm’s reach. Hang your essential grilling

tools on the hooks for easy access and organization of

your backyard workspace.

E Sear Station

The Sear Station is designed to create an intense heat

zone to quickly add sear marks to your meat.

F iGRILL3 Compatible

The iGrill 3 app-connected thermometer monitors

food from beginning to end, displaying the real-time

temperature on your mobile device. (Accessory sold

separately.)

G Side Burner

Use the side burner to simmer BBQ sauce or sauté

veggies while the main course grills under the lid.

H Fuel Gauge

The easy-to-read fuel gauge located next to the gas

tank lets you see how much fuel is left in the tank.

I Side Mounted Gas Tank

Mounting the gas tank to the outside of the grill makes

it easier to access and remove.

J Open Cart Design

The sleek open-cart design provides easy accessibility

of your grilling tools.

A

B

C

D

E

F G

H

I

J

GS4 HIGH

PERFORMANCE

GRILLING SYSTEM

4 Grease Management System

Drippings that are not vaporized by the FLAVORIZER

BARS are funneled away from the burners into the

disposable drip tray, located within the removable

catch pan under the cookbox. Simply remove the

catch pan and replace the drip tray as needed.

The GS4 high performance grilling

system sets the standard in the

world of gas grilling, and lands

Weber in a class of its own. This

powerful grilling system is based on

over 65 years of grilling experience,

culinary expertise, and most importantly, the wants

and needs of the people who matter most – our

grilling community. Each component of GS4 was

uniquely designed for ease-of-use and to provide

an unequaled satisfaction to your backyard grilling

experience.

1 INFINITY Ignition

The Inﬁnity Ignition is guaranteed to

ignite. Rest assured that you’ll be up-and-

grilling the ﬁrst time, every time.

2 Burners

The unique, tapered shape delivers a consistent gas

ﬂow from front to back. This provides ultimate heat

distribution, ensuring that food grills evenly and

consistently anywhere on the cooking grates.

3 FLAVORIZER BARS

Stainless Steel FLAVORIZER BARS are angled just

right to catch drippings that smoke and sizzle,

adding that irresistible smoky ﬂavor that we all

know and love to your food.

2

3

4

6

Tips and Hints

INDIRECT HEAT

SETUP

Use the indirect method for larger cuts of meat that require 20 minutes or

more of grilling time, or for foods so delicate that direct exposure to the heat

would dry them out or scorch them, such as: roasts, bone-in poultry pieces,

whole ﬁsh, delicate ﬁsh ﬁllets, whole chickens, turkeys, and ribs. Indirect heat

can also be used for ﬁnishing thicker foods or bone-in cuts that have been

seared or browned ﬁrst over direct heat.

With indirect heat, the heat is on both sides of the grill, or o to one side of

the grill. The food sits over the unlit part on the cooking grate.

The Flame -

Direct or Indirect

DIRECT HEAT

SETUP

Use the direct method for small, tender pieces of food that take less than

20 minutes to cook, suchas: hamburgers, steaks, chops, kabobs, boneless

chicken pieces, ﬁsh ﬁllets, shellﬁsh, and slicedvegetables.

With direct heat, the ﬁre is right below the food. It sears the surfaces of the

food, developing ﬂavors, texture, and delicious caramelization while cooking

the food all the way to thecenter.

TIMER

Avoid the disappointment of torching

your dinner by simply setting a timer.

Nothing fancy needed—just one

that is reliable and easy

to use.

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

OFF

LOW

MEDIUM

START/HIGH

BARBECUE

MITTS

When in doubt, wear them. The good

ones are insulated and protect

both hand and forearm.

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

HIGH

MEDIUM

OFF

7

Preheat each and every time.

If the cooking grates aren’t hot enough, food will stick,

and you will likely never have a chance of searing

properly or developing those handsome grill marks.

Even if a recipe calls for medium or low heat, always

preheat the grill on the highest setting ﬁrst. Open the

lid, turn up the heat, close the lid, and then let the

cooking grate heat up for about ten minutes or until the

lid thermometer reads 500° F (260° C).

Don't grill on dirty grates.

Tossing food onto the cooking grates before they have

been cleaned is never a good idea. Leftover “stu” on

the grates acts like glue, binding it to the grates and

your new food. To avoid tasting last night’s dinner on

today’s lunch, make sure you are grilling on a clean

cooking grate. Once the grates are preheated, use

a stainless steel bristle grill brush to make a clean,

smooth surface.

Be present in the process.

Before ﬁring up your grill, make sure that everything

you need is within arm’s reach. Don’t forget your

essential grilling tools, already oiled and seasoned

food, glazes or sauces, and clean cooking platters for

cooked food. Having to run back to your kitchen not only

means missing out on the fun, but could also result in

burning your food. French chefs call this “mise en place”

(meaning, “put in place”). We call it “being present”.

Create a little elbow room.

Packing too much food onto the cooking grates restricts

your ﬂexibility. Leave at least one-quarter of the cooking

grates clear, with plenty of space between each food

item, in order to get your tongs in there and easily

move the food around. Sometimes grilling involves

split-second decisions and the ability to jockey food

from one area to another. Sogive yourself enough room

to operate.

Try not to peek.

The lid on your grill is for more than just keeping the

rain out. Most importantly, it’s for preventing too much

air from getting in, and too much heat and smoke from

getting out. When the lid is closed, the cooking grates

are hotter, the grilling times are faster, the smoky tastes

are stronger, and the ﬂare-ups are fewer. So put a lid

on it!

Only flip once.

What’s better than a juicy steak with a deep sear and

plenty of beautifully caramelized bits? The key to

accomplishing these results is to keep your food in

place. Sometimes we have the tendency to ﬂip our food

before it reaches the desirable level of color and ﬂavor.

In nearly all cases, you should turn food just once. If

ﬁddling with it more than that, you are probably also

opening the lid too much, which causes its own set of

problems. So step back and trust the grill.

Know when to tame the flame.

When grilling, sometimes the most important thing to

know is when to stop. The most reliable way to test

doneness of your food is to invest in an instant-read

thermometer. This slim little gem will help you pinpoint

that critical moment when your food is at its best.

Don’t be afraid to experiment.

Back in the 1950s, grilling meant one thing: meat (and

only meat) charred over open ﬂames. The modern

day backyard chef doesn’t need a kitchen in order to

prepare a full course meal. Use your grill to make char-

grilled appetizers, sides, and even desserts. Register

your grill to receive special content that will inspire

you along the way. We’d love to join you on your grilling

adventures.

Tips and Hints

GrillingDo’s

andDon’ts

Optimize

Grill Space

Using the TUCKAWAY

Warming Rack

Use the warming rack up to keep food warm

or fold it down when not in use. To fold the

warming rack down, lift rack slightly and rotate

downward. Use heat-resistant mitts or gloves

when adjusting rack.

8

Getting Started

Important Information about

LPGas & Gas Connections

What Is LP Gas?

Liqueﬁed petroleum gas, also called LP, LP gas, liquid

propane, or simply propane or butane, is the ﬂammable,

petroleum-based product used to fuel your grill. It is

a gas at moderate temperatures and pressure when

it is not contained. But at moderate pressure inside a

container, such as a tank, LP is a liquid. As pressure is

released from the tank, the liquid readily vaporizes and

becomes gas.

Safe Handling Tips For LP Tanks

• A dented or rusty liquid propane tank may be

hazardous and should be checked by your liquid

propane supplier. Donot use a liquid propane tank

with a damaged valve.

• Although your liquid propane tank may appear to be

empty, gas may still be present, and the tank should be

transported and stored accordingly.

• The LP tank must be installed, transported, and stored

in an upright, secure position. LP tanks should not be

dropped or handled roughly.

• Never store or transport the LP tank where

temperatures can reach 125° F (51.7° C) (the tank will

become too hot to hold by hand).

• Place dust cap on tank valve outlet whenever the tank

is not in use. Only install the type of dust cap on the

tank valve outlet that is provided with the tank valve.

Other types of caps or plugs may result in leakage of

propane.

LP Tank Requirements

• The tank must be approximately 18¼inches (46.35

cm) high and 12¼ inches (31.1 cm) in diameter with a

marked 20 pound (9.07 kg) LPG capacity or 47.6 pound

(21.6 kg) water capacity as stated by the manufacturer.

Other tanks may be acceptable provided they are

compatible with the grill retention means (tank scale).

• The tank used must be constructed and marked

in accordance with the Speciﬁcations for LP gas

Cylinders of the U.S. Department of Transportation

(D.O.T.); or the Canadian Standard for Cylinders,

Spheres and Tubes for Transportation of Dangerous

Goods and Commission, CAN/CSA-B339, as applicable.

• Tanks must be provided with a listed OPD (Overﬁlling

Prevention Device) and a Type 1 (CGA 810) tank

connection. The tank connection must be compatible

with the grill connection.

• The tank must include a collar to protect the tank

valve.

• Tanks must have a D.O.T. certiﬁcation (A), and a testing

date (B) that is within ﬁve years of current use.

What is a Regulator?

Your gas grill is equipped with a pressure regulator,

which is a device to control and maintain uniform gas

pressure as gas is released from the LP tank.

Regulator Requirements

• The regulator and hose assembly supplied with this

grill must be used. This regulator has a ﬂow limiting

device built into the unit that will restrict the ﬂow of

gas in the event that a leak is detected.

• Replacement regulator and hose assemblies must be

as speciﬁed by Weber-Stephen Products LLC (UL-listed

Type 1 (CGA 810) tank connection device as described

in the latest edition of ANSI Z21.81).

A

B

9

Getting Started

LP Tank Installation &

LeakChecking

Installation Location

The tank is hung onto the tank scale which is located

outside the cabinet base under the right side table.

The shape of the collar assembly (the metal protective

ring around the tank valve) determines one of two

directions in which the tank will correctly hang on the

tank scale (A).

Inspect the Tank

1) Conﬁrm that the tank valve is fully closed. Close by

turning valve clockwise.

2) Conﬁrm that the tank valve is the proper mating

type for the regulator (B).

3) Inspect the tank valve, including the internal rubber

seal for damage or debris (C). If damaged, return

tank to local retailer.

Install The Tank

1) Check that all burner control knobs are in the

o position. Check by pushing in and turning

knobs clockwise.

2) Loosen hand nut and rotate tank lock up(D).

3) Lift tank into position on the tank scale (E).

4) Rotate the tank lock down. Tighten the hand nut.

5) Screw the regulator coupling onto the tank valve,

turning clockwise (F). Hand-tighten only. Using a

wrench could damage the regulator coupling and

could cause a leak. Proceed to “CHECKING FOR

GASLEAKS.”

A

B

C

D

E

F

10

Getting Started

m DANGER: Do not use a ﬂame to check for gas

leaks. Besure there are no sparks or open

ﬂames in the area while you check for leaks.

m DANGER: Leaking gas may cause a ﬁre or

explosion.

m DANGER: Do not operate the grill if there is a

gas leak present.

m DANGER: If you see, smell, or hear the hiss of

gas escaping from the liquid propane tank:

1) Move away from liquid propane tank.

2) Do not attempt to correct the problem

yourself.

3) Call your ﬁre department.

m DANGER: Always close the tank valve before

disconnecting the regulator. Do not attempt

to disconnect the gas regulator and hose

assembly or any gas ﬁtting while this grill is

in operation.

m DANGER: Do not store a spare LP tank under

or near this grill. Never ﬁll the tank beyond

80% full. Failure to follow these statements

exactly may result in a ﬁre causing death or

serious injury.

G

H

I

What is a Leak Check?

Once the LP tank is properly installed, it is necessary

to perform a leak check. A leak check is a reliable way

to verify that gas is not escaping after you connect the

tank. The fuel system in your grill features factory-

made connections that have been thoroughly checked

for gas leaks and the burners have been ﬂame-tested.

WEBER recommends performing a thorough leak

check after assembly, as well as annually. The

following ﬁttings should be tested:

• Where the regulator connects to the tank.

• Where the gas hose connects to the bulkhead.

• Where the bulkhead connects to the corrugated gas

line.

Checking for Gas Leaks

1) Wet ﬁttings (G) with a soap and water solution,

using a spray bottle, brush, or rag. You can make

your own soap and water solution by mixing 20%

liquid soap with 80% water; or, you can purchase

leak check solution in the plumbing section of any

hardware store.

2) Slowly open gas supply by turning tank valve

counterclockwise while checking for bubbles.

3) If bubbles appear there is a leak:

a) If the leak is at the cylinder (H), turn o the gas.

DONOT OPERATE THE GRILL. Disconnect the

tank and return the tank to your local retailer.

b) If the leak is at the regulator (I), turn o the

gas. DONOT OPERATE THE GRILL. Contact the

Customer Service Representative in your area

using the contact information on our website.

c) If the leak is at any ﬁttings indicated in

illustration (J), re-tighten ﬁtting with a wrench

and recheck for leaks with soap and water

solution. If leak persists, turn o the gas. DO NOT

OPERATE THE GRILL.

d) If the leak is at any ﬁttings indicated in

illustration (K), turn o the gas. DO NOT

OPERATE THE GRILL.

If a leak is present, contact the Customer Service

Representative in your area using the contact

information on our website.

4) If bubbles do not appear, leak checking is complete:

a) Turn gas supply o at the tank and rinse

connections with water.

NOTE: Since some leak test solutions, including soap and

water, may be slightly corrosive, all connections should

be rinsed with water after checking for leaks.

K

J

11

Getting Started

N

O

Refilling or Replacing an

LPTank

How Much Fuel is in the Tank?

The tank scale indicates the amount of fuel in a

standard 20 pound (9.07 kg) tank once the tank is hung

from the scale. The fuel level is checked by viewing

the red level indicator line, located on scale. When the

indicator line is at the top, the tank is full (L). When it

is at the bottom, the tank is empty(M) and needs to be

removed to replace or reﬁll.

Removal of the LP Tank

1) Conﬁrm that the tank valve is fully closed. Close by

turning valve clockwise (N).

2) Unscrew regulator coupling by turning

counterclockwise by hand (O).

3) Loosen tank hand nut and turn tank lock up out of

the way.

4) Lift tank o tank scale.

Additional Leak Check Precautions

The following ﬁttings should be tested for gas leaks

each time a tank is reﬁlled and reinstalled:

• Where the regulator connects to the tank (H) and at

the regulator (I).

Follow the instructions for "Checking for Gas Leaks".

L

M

Getting Started

GRILLINGPAN

Designed for food that is either too

small or too delicate for the cooking

grates, a perforated grilling pan

keeps food right where it ought

tobe—on the grill,

not in it.

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

TONGS

Consider these to be an extension

of your hand. The best tongs

should have an eortless tension

mechanism, comfortable hand

grips, and a lock to keep

themcompact.

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

BRUSH

AND MOP

Look for a basting brush with heat-

resistant silicone bristles and a long

handle, and a mop with long, cotton

threads that sop up the thinner,

vinegar-based sauces.

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

12

Operation

The Very First Time You Grill

Perform an Initial Burn-Off

Heat the grill on the highest setting, with the lid closed,

for at least 20 minutes prior to grilling for the ﬁrsttime.

Every Time You Grill

Meal-to-Meal Maintenance

The Meal-To-Meal Maintenance plan includes the

following simple, yet important, steps that should

always be performed prior to grilling.

Check for Grease

Your grill was built with a grease management

system that funnels grease away from food and into a

disposable container. As you cook, grease is channeled

down the slide-out grease tray and into a disposable

drip tray that lines the catch pan. This system should be

cleaned each and every time you grill to preventﬁres.

1. Conﬁrm that the grill is o and cool.

2. Remove the slide-out grease tray by pulling the tray

out of the cabinet (A). Remove excess grease with a

plastic scraper.

3. Remove the catch pan by pressing down on the catch

pan latch (B). Check for excessive amounts of grease

in the disposable drip pan that lines the catch pan.

Discard disposable drip pan when necessary and

replace with a new one.

4. Reinstall all components.

Inspect the Hose

Routine inspection of the hose is necessary.

1. Conﬁrm that the grill is o and cool.

2. Check hose for any signs of cracking, abrasions, or

cuts(C). If the hose is found to be damaged in any

way, do not use the grill.

Preheat the Grill

Preheating the grill is critical to successful grilling.

Preheating helps to prevent food from sticking to the

grate and gets the grate hot enough to sear properly.

Italso burns o residue of a previously cooked meal.

1. Open the grill lid.

2. Ignite your grill according to the ignition instructions

in this Owner's Manual.

3. Close lid.

4. Preheat the grill with all burners on the start/high

position for 10 to 15 minutes or until thermometer

registers 500° F (260° C)(D).

Clean the Cooking Grate

After preheating, any bits of food or debris left over from

previous use will be easier to remove. Cleaned grates

will also prevent your next meal from sticking.

1. Brush the grates with a stainless steel bristle grill

brush immediately after preheating (E).

m DANGER: Do not line the slide-out grease tray

or cookbox with aluminum foil.

m DANGER: Check the slide-out grease tray and

catch pan for grease build-up before each use.

Remove excess grease to avoid a grease ﬁre.

m WARNING: Use heat-resistant barbecue mitts

or gloves when operating grill.

m WARNING: Grill brushes should be checked for

loose bristles and excessive wear on a regular

basis. Replace brush if any loose bristles are

found on cooking grates or brush. WEBER

recommends purchasing a new stainless steel

bristle grill brush at the beginning of every

spring.

m WARNING: If the hose is found to be damaged

in any way, do not use the grill. Replace using

only WEBER authorized replacement hose.

m WARNING: Keep ventilation openings around

tank clear and free of debris.

A

B

C

D

E

13

A

B

C

D

E

Operation

m WARNING: Open lid during ignition.

m WARNING: Do not lean over open grill while

igniting or cooking.

m WARNING: Each burner must be ignited

individually by pushing the electronic ignition

button.

m WARNING: If ignition does not occur within

four seconds of attempting to light the ﬁrst

burner, turn the burner control knob to

the o position. Wait ﬁve minutes to allow

accumulated gas to dissipate, and then repeat

the lighting procedure.

Igniting the Grill

Using the Electronic Ignition System to

Ignite the Grill

Each control knob operates an individual burner, and

each burner ignites independently. Ignite the burners

starting from left to right. All burners should be lit for

preheating, however, all burners do not have to be lit

while grilling.

1) Open the grill lid (A).

2) Check that all burner control knobs are in the o

position. Check by pushing in and turning knobs

clockwise (B).

Note: It is important that all burner control knobs are

in the o position before turning on the LP tank.

If they are not, the ﬂow limiting device built into the

regulator will activate, limiting the ﬂow of gas from

the LP tank.

3) Turn the LP tank on by slowly turning the tank valve

counterclockwise; wait 60 seconds (C).

Note: It is important that the LP tank is turned on

slowly. Ifit is opened too quickly, the ﬂow limiting

device built into the regulator will activate, limiting the

ﬂow of gas from the LP tank.

4) Begin with the burner furthest to the left. Push the

burner control knob in and turn it counterclockwise

to the start/high

position (D).

5) Push and hold the electronic ignition button (E).

Youwill hear it ticking.

6) Check that the burner is lit by looking through the

cooking grates and through the half-circle cutout in

the FLAVORIZER bar.

7) If the burner does not ignite, turn burner control

knob to the o

position and wait ﬁve minutes to

allow the gas to clear before attempting to light the

burner again.

8) If the burner ignites, repeat steps 4 through 6 to

light the remaining burners.

Should the burners fail to ignite using the electronic

ignition, refer to the TROUBLESHOOTING section.

Thereyou will ﬁnd instructions on igniting the grill

with a match to help determine the exact problem.

To Extinguish Burners

1) Push each burner control knob in and then turn

clockwise all the way to the o position.

2) Turn gas supply o at the LP tank.

A

B

C

D

E

14

Operation

1

B

Using the Sear Station

Searing is a direct grilling technique used on meats,

such as steak, poultry parts, ﬁsh and chops. Searing

browns the surface of the food at a high temperature. By

searing both sides of the meat, you caramelize the food

surface, creating a more desirable ﬂavor.

Ignition of the sear burner

is the same as ignition of a

main burner, each burner ignites independently.

1) Open the lid and ignite all of the burners,

including the sear burner . Refer to USING THE

ELECTRONIC IGNITION SYSTEM TO IGNITE THE

GRILL.

2) Preheat the grill with the lid closed and with all

burners on the start/high

position for 10 to 15

minutes or until thermometer registers 500° F

(260° C).

3) After preheating, leave the sear burner control

knob

and the adjacent burner control knobs in

the start/high position (A). The sear burner works

in tandem with adjacent burners (B). The remaining

burner(s) can be turned to o or low.

4) Place meat directly over the sear station

and close

lid. Sear each side anywhere from one to four

minutes (C), depending on the type and thickness

of meat. Once searing is complete, the meat can be

moved to moderate heat over and cooked to your

desired doneness.

Note: Always cook with the lid closed to achieve maximum

heat and to avoid ﬂare-ups.

As you gain experience using the sear station we

encourage you to experiment with dierent searing

times to ﬁnd the results that work best for your taste.

To Extinguish Burners

1) Push each burner control knob in and then turn

clockwise all the way to the o position.

2) Turn gas supply o at the LP tank.

15

m WARNING: Open side burner lid during ignition.

m WARNING: Do not lean over side burner while

igniting or cooking.

m WARNING: If ignition does not occur within

four seconds of attempting to light the side

burner, turn the burner control knob to

the o position. Wait ﬁve minutes to allow

accumulated gas to dissipate, and then repeat

the lighting procedure.

Igniting the Side Burner

Using the Electronic Ignition to

Ignite the Side Burner

If one or more of the main burners on your grill are

already lit and you would like to ignite the side burner,

skip to step 3. If none of the main burners are lit and

you are only using the side burner, start with step 1.

1) Check that the side burner control knob is in the

o

position. Check by pushing in and turning

knob clockwise (A). Also check that all main burner

control knobs are in the o

position.

Note: It is important that all burner control knobs are

in the o position before turning on the LP tank.

If they are not, the ﬂow limiting device built into the

regulator will activate, limiting the ﬂow of gas from

the LP tank.

2) Turn the LP tank on by slowly turning the tank valve

counterclockwise; wait 60 seconds.

Note: It is important that the LP tank is turned on

slowly. Ifit is opened too quickly, the ﬂow limiting

device built into the regulator will activate, limiting the

ﬂow of gas from the LP tank.

3) Open the side burner lid (B).

4) Push in and turn side burner control knob

counterclockwise to start/high

position (C).

5) Push and hold in the electronic ignition button (D).

You will hear the igniter clicking. Check that the side

burner is lit. The side burner ﬂame may be dicult

to see on a bright sunny day.

6) Once side burner is ignited, continue turning the

knob counterclockwise until you reach the desired

position.

7) If the side burner does not ignite within 4 seconds,

turn side burner control knob to the o

position

and wait ﬁve minutes to allow the gas to clear

before attempting to light the burner again.

Should the side burner fail to ignite using the

electronic ignition, refer to the TROUBLESHOOTING

section. Thereyou will ﬁnd instructions on igniting the

side burner with a match to help determine the exact

problem.

To Extinguish Side Burner

1) Push side burner control knob in and then turn

clockwise all the way to the o position.

2) Turn gas supply o at the LP tank.

B

D

Operation

16

Product Care

m WARNING: Turn your grill o and wait for it to

cool before thoroughly cleaning.

m WARNING: Over time, the development of

rough surfaces can form on the FLAVORIZER

BARS. Wearing gloves is recommended when

handling. Do not clean FLAVORIZER BARS or

cooking grates in a sink, dishwasher, or self-

cleaning oven.

m WARNING: When cleaning the burners, never

use a brush that has already been used to

clean the cooking grates. Never put sharp

objects into the burner port holes.

m CAUTION: Do not place any grill components

onto the side tables as they may scratch the

paint or stainless steel surfaces.

m CAUTION: Do not use any of the following

to clean your grill: abrasive stainless steel

polishes or paints, cleaners that contain

acid, mineral spirits or xylene, oven cleaner,

abrasive cleansers (kitchen cleansers), or

abrasive cleaning pads.

Cleaning and Maintenance

Cleaning the Inside of the Grill

Over time, the performance of your grill can

diminish if it has not been maintained properly.

Low temperatures, uneven heat, and food sticking

to cooking grates are all signs that cleaning and

maintenance are overdue. When your grill is o and

cool, start by cleaning the inside, from the top down.

A thorough cleaning is recommended at least twice a

year. Consistent use may require quarterly cleanings.

Cleaning the Lid

From time to time you may notice “paint-like” ﬂakes

on the inside of the lid. During use, grease and smoke

vapors slowly change into carbon and deposit on the

inside of your lid. These deposits will eventually peel,

and looks very similar to paint. These deposits are

non-toxic, but the ﬂakes could fall onto your food if you

do not clean the lid regularly.

1) Brush the carbonized grease from the inside of the

lid with a stainless steel bristle grill brush (A). To

minimize further build-up, the inside of the lid can

be wiped with a paper towel after grilling while the

grill is still warm (nothot).

Cleaning the Cooking Grates

If you have been cleaning your cooking grates as

recommended, the debris on your grates should be

minimal.

1) With grates installed, brush the debris o your

cooking grate with a stainless steel bristle grill

brush(B).

2) Take the grates out and set aside.

Cleaning the FLAVORIZERBARS

FLAVORIZER BARS catch drippings that smoke and

sizzle, adding ﬂavor to your food. Any drippings that

are not vaporized by the FLAVORIZER BARS are

funneled away from the burners. This helps prevent

ﬂare-ups inside of your grill, and protects the burners

from getting clogged.

1) Scrape the FLAVORIZER BARS with a plastic

scraper(C).

2) If necessary, brush the FLAVORIZER BARS with a

stainless steel bristle grill brush.

3) Remove FLAVORIZER BARS and set aside.

Cleaning the Burners

Two areas on the burners that are key to optimum

performance are the ports (small raised openings

running along the length of the burners) and the

spider/insect screens on the ends of the burner.

Keeping these areas clean is essential for safe

operation.

Cleaning the Burner Ports

1) Use a clean stainless steel bristle grill brush to

clean the outside of the burners by brushing across

the top of the burner ports (D).

2) When cleaning the burners, avoid damaging the

ignition electrode by carefully brushing around

it(E).

Cleaning the Spider Screens

1) Locate the ends of the burners on the underside of

the control panel where they meet the valves.

2) Clean the spider/insect screens on each of the

burners using a soft bristle brush (F).

A

B

C

D

E

F

17

Cleaning the Heat Deflectors

Located under the burners, the heat deﬂectors

distribute heat evenly throughout the cookbox while

cooking. Keeping heat deﬂectors clean will enhance

the cooking performance of your grill.

1) Scrape the heat deﬂectors with a plastic

scraper(G).

2) If necessary, brush the heat deﬂectors with a

stainless steel bristle grill brush.

3) Remove heat deﬂectors and set aside.

Cleaning the Cookbox

Look inside the cookbox for any grease accumulation

or leftover food particles. Excessive accumulation can

cause a ﬁre.

1) Use a plastic scraper to scrape debris o the sides

and bottom of the grill into the opening in bottom of

the cookbox(H). This opening leads debris into the

slide-out grease tray.

Cleaning the Grease ManagementSystem

The grease management system consists of an

angled slide-out grease tray and a catch pan. These

components were designed to be easily removed,

cleaned, and replaced; an essential step every time

you prepare to grill. Instructions on inspecting the

grease management system can be found in MEAL-TO-

MEAL MAINTENANCE.

Cleaning the Outside of theGrill

The outside of your grill may include stainless steel,

porcelain-enameled, and plastic surfaces. WEBER

recommends the following methods based on the

surfacetype.

Cleaning Stainless Steel Surfaces

Clean stainless steel using a non-toxic, non-abrasive

stainless steel cleaner or polish designed for use on

outdoor products and grills. Use a microﬁber cloth to

clean in the direction of the grain of the stainless steel.

Donot use paper towels.

Note: Do not risk scratching your stainless steel with

abrasive pastes. Pastes do not clean or polish. They

will change the color of the metal by removing the top

chromium oxide ﬁlm coating.

Cleaning Painted, Porcelain-Enameled

Surfaces and PlasticComponents

Clean painted, porcelain-enameled and plastic

components with warm soapy water, and paper towels

or cloth. After wiping down the surfaces, rinse and dry

thoroughly.

Cleaning the Outside of Grills that are in

Unique Environments

If your grill is subject to a particularly harsh

environment, you will want to clean the outside more

often. Acid rain, pool chemicals, and salt water can

cause surface rusting to appear. Wipe down the

outside of your grill with warm soapy water. Follow

up with a rinse and thorough drying. Additionally, you

may want to apply a stainless steel cleaner weekly to

prevent surface rust.

GRILLBRUSH

A must-use before you even dream

of grilling. A quick once-over on hot

grates prevents the charred remains

of meals past from sticking to

your meals present.

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

THERMOMETER

Small and relatively inexpensive,

this gadget is essential for quickly

gauging the internal temperature

of the meat when grilling.

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

G

H

FOILPANS

Perfect for lining the

catchpan to make cleanup

convenient and easy.

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

M

U

S

T

-

H

A

V

E

G

R

I

L

I

N

G

T

O

L

S

•

Product Care

18

Troubleshooting

MAIN BURNERS or SIDE BURNER WILL NOT IGNITE

SYMPTOM

• Main burners or side burner do(es) not ignite when following the electronic ignition instructions in the “Operation” section of

this owner's manual.

CAUSE SOLUTION

There is a problem with gas ﬂow. If any burner does not ignite, the ﬁrst step is to determine if there is gas ﬂowing to the burner(s). Tocheck

this, follow the instructions below for “Lighting Your Grill with a Match.”

If match lighting IS NOT successful, follow the “GAS FLOW” troubleshooting suggestions on the next page.

There is a problem with the electronic ignition system. If any burner does not ignite, the ﬁrst step is to determine if there is gas ﬂowing to the burner(s). Tocheck this,

follow the instructions below for “Lighting Your Grill with a Match.”

If match lighting IS successful, follow the instructions for “Checking the Components of the Electronic

IgnitionSystem.”

Lighting Your Grill with a Match

Using a Match to Determine if there is

Gas Flow to the Main Burners

1) Open the grill lid.

2) Check that all burner control knobs (including side

burner control knob) are in the o

position. Check

by pushing in and turning knobs clockwise.

Note: It is important that all burner control knobs are

in the o position before turning on the LP tank.

If they are not, the ﬂow limiting device built into the

regulator will activate, limiting the ﬂow of gas from

the LP tank.

3) Turn the LP tank on by slowly turning the tank valve

counterclockwise; wait 60 seconds.

Note: It is important that the LP tank is turned on

slowly. Ifit is opened too quickly, the ﬂow limiting

device built into the regulator will activate, limiting the

ﬂow of gas from the LP tank.

4) Begin with the burner furthest to the left. Put

match in the matchstick holder and strike match.

(Matchstick holder is located under right side

table.) Insert lit match down through the cooking

grates, past the FLAVORIZER bars and next to the

burner(A).

5) Pushthe burner control knob in and slowly turn it

counterclockwise toward the start/high

position.

6) Check that the burner is lit by looking through

the cooking grates and through the cutout in the

FLAVORIZER bar.

7) If the burner does not ignite within 4 seconds,

turn burner control knob to the o

position and

wait ﬁve minutes to allow the gas to clear before

attempting to light the burner again. If repeated

attempts fail, follow the gas ﬂow troubleshooting

instructions on the next page.

8) If the burner ignites, the problem lies in the ignition

system. Follow the instructions for “Checking the

Components of the Electronic Ignition System”.

9) Replace the matchstick holder by hanging

underneath right side table (B).

Using a Match to Determine if there is

Gas Flow to the Side Burner

1) Open the side burner lid.

2) Check that the side burner control knob is in the

o

position. Check by pushing in and turning knob

clockwise. Also check that all main burner control

knobs are in the o position.

Note: It is important that all burner control knobs are

in the o position before turning on the LP tank.

If they are not, the ﬂow limiting device built into the

regulator will activate, limiting the ﬂow of gas from

the LP tank.

3) Turn the LP tank on by slowly turning the tank valve

counterclockwise; wait 60 seconds.

Note: It is important that the LP tank is turned on

slowly. Ifit is opened too quickly, the ﬂow limiting

device built into the regulator will activate, limiting the

ﬂow of gas from the LP tank.

4) Put match in the matchstick holder and strike

match. (Matchstick holder is located under right

side table.) Hold lit match by the side burner(C).

5) Pushthe side burner control knob in and slowly

turn it counterclockwise toward the start/high

position.

6) Check that the side burner is lit. The side burner

ﬂame may be dicult to see on a bright sunny day.

7) If the side burner does not ignite within 4 seconds,

turn side burner control knob to the o

position

and wait ﬁve minutes to allow the gas to clear

before attempting to light the burner again.

If repeated attempts fail, follow the gas ﬂow

troubleshooting instructions on the next page.

8) If the burner ignites, follow the instructions for

“Checking the Components of the Electronic Ignition

System”.

A

B

C

REPLACEMENT

PARTS

To obtain replacement parts,

contact the local retailer

in your area or log onto

weber.com.

19

Proper Burner Flame Pattern

The burners in your grill were factory set for the

correct air and gas mixture. When the burners

are performing correctly, you will see a speciﬁc

ﬂame pattern. The tips may occasionally ﬂicker

yellow (A), with a descending light blue (B) to

dark blue ﬂame (C).

m WARNING: Do not attempt to make any

repair to gas carrying, gas burning, ignition

components or structural components without

contacting Weber-Stephen Products LLC,

Customer Service Department.

m WARNING: Failure to use genuine Weber-

Stephen parts for any repair or replacement

will void all warranty protection.

m CAUTION: The burner tube openings must be

positioned properly over the valve oriﬁces.

Spider Screens

The combustion air openings of the burners(D)

are ﬁtted with stainless steel screens to

prevent spiders and other insects from spinning

webs and building nests inside the burners.

Additionally, dust and debris can accumulate

on the outside of the spider/insect screen and

obstruct the oxygen ﬂow to the burners.

D

A

B

C

GAS FLOW

SYMPTOM

• Grill does not reach desired temperature or heatsunevenly.

• One or more of the burners fail to ignite.

• Flame is low when burner is on high position.

• Flames do not run the whole length of the burner.

• Burner flame pattern is erratic.

CAUSE SOLUTION

The “ﬂow limiting device” has been activated.

Thissafety feature built into the regulator restricts

the gas ﬂow in the event of a gas leak. You can

inadvertently activate this safety feature without

having a gas leak. This typically occurs when you

turn on the gas at the LP tank and one or more of the

control knobs are not in the o position. It may also

occur if you turn on the LP tank too quickly.

Reset the “ﬂow limiting device” by closing the LP

tank valve and turning all the burner control knobs

to the o position. Wait ﬁve minutes to allow

accumulated gas to dissipate, then ignite the grill

again following the instructions in the “Operation”

section.

The LP tank is low or empty. Reﬁll LP tank.

Fuel hose is bent or kinked. Straighten fuel hose.

Burner ports are dirty. Clean burner ports. Refer to “Cleaning the

BurnerPorts.”

SYMPTOM

• Gas is smelled in conjunction with burner flames that appear yellow andlazy.

CAUSE SOLUTION

Spider screens on the burners are obstructed. Clean spider screens. Refer to “Cleaning the Spider

Screens” in the Product Care section. Also refer to

the illustrations and information in this section about

proper ﬂame pattern and spiderscreens.

SYMPTOM

• The smell of gas and/or a light hissing sound.

CAUSE SOLUTION

The internal rubber seal in the LP tank valve could be

damaged.

Inspect the rubber seal for damage. If damaged,

return tank to local retailer.

Troubleshooting

20

Troubleshooting

Checking the Components of the

Electronic Ignition System

When pressing the ignition button you should hear a

ticking sound. If you cannot hear the ticking sound,

check the battery, then check the wires.

Checking the Battery

There are three potential issues with the battery that

supplies the power to your ignition module that need

to be checked:

1) Some batteries have a plastic protective wrap

around them. (Do not confuse this plastic with

the battery label.) Check that this plastic wrap is

removed.

2) Conﬁrm that the battery is installed correctly (C).

3) If the battery is old, replace it with a new battery.

CALL

CUSTOMER

SERVICE

If you are still experiencing any

problems, contact the CustomerService

Representative in your area using

the contact information on

weber.com.

C

GREASY GRILL (Peeling Paint & Flare-Ups)

SYMPTOM

• Inside of lid appears to have the appearance of peelingpaint.

CAUSE SOLUTION

The ﬂakes you see are accumulated cooking vapors

that have turned into carbon.

This happens over time after repeated use of your

grill. This is not a defect. Clean the lid. Refer to the

“Product Care” section.

SYMPTOM

• Experiencing flare-ups when grilling or preheating.

CAUSE SOLUTION

There is leftover food from the previous meal. Always preheat the grill on the highest setting for 10

to 15 minutes.

The inside of the grill needs to be cleaned thoroughly. Follow the steps in the "Cleaning and Maintenance"

section to clean the grill inside from the top down.

Checking the Wires

There are two potential trouble spots that need to be

checked:

1) Check that the ignition wires are connected

securely to the terminals on the ignition button

under the control panel.

2) Make sure the ignition wires are properly attached

to the ignition module. The wire terminals are color

coded to correspond with the terminals on the

ignition module. The number of wires will vary per

model.

330 Igniter Module Wire Chart

1 2 3 4 5

5

3

1

4

2

La page charge ...

Weber 61012001 Manuel utilisateur

Ce manuel convient également à

Weber 61012001 Manuel utilisateur

dans d''autres langues

Documents connexes