Hilti SF/SFD 2-A Mode d'emploi

SF 2A

SFD 2-A

English 1

Français 15

Español 30

Português 45

Printed: 07.01.2019 | Doc-Nr: PUB / 5174907 / 000 / 02

1

2

3

4

Printed: 07.01.2019 | Doc-Nr: PUB / 5174907 / 000 / 02

5

Printed: 07.01.2019 | Doc-Nr: PUB / 5174907 / 000 / 02

SF 2A

SFD 2-A

en Original operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . 1

fr Mode d'emploi original . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

es Manual de instrucciones original . . . . . . . . . . . . . . . . . . . . . . . 30

pt Manual de instruções original . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Printed: 07.01.2019 | Doc-Nr: PUB / 5174907 / 000 / 02

*2081399*

2081399 English 1

1 Information about the documentation

1.1 About this documentation

• Read this documentation before initial operation or use. This is a

prerequisite for safe, trouble-free handling and use of the product.

• Observe the safety instructions and warnings in this documentation and

on the product.

• Always keep the operating instructions with the product and make sure

that the operating instructions are with the product when it is given to

other persons.

1.2 Explanation of symbols used

1.2.1 Warnings

Warnings alert persons to hazards that occur when handling or using the

product. The following signal words are used:

DANGER

DANGER !

▶ Draws attention to imminent danger that will lead to serious personal

injury or fatality.

WARNING

WARNING !

▶ Draws attention to a potential threat of danger that can lead to serious

injury or fatality.

CAUTION

CAUTION !

▶ Draws attention to a potentially dangerous situation that could lead to

slight personal injury or damage to the equipment or other property.

1.2.2 Symbols in the documentation

The following symbols are used in this document:

Read the operating instructions before use.

Instructions for use and other useful information

Dealing with recyclable materials

Do not dispose of electric equipment and batteries as household

waste

1.2.3 Symbols in the illustrations

The following symbols are used in illustrations:

Printed: 07.01.2019 | Doc-Nr: PUB / 5174907 / 000 / 02

2 English 2081399

*2081399*

These numbers refer to the corresponding illustrations found at the

beginning of these operating instructions

The numbering reflects the sequence of operations shown in the

illustrations and may deviate from the steps described in the text

Item reference numbers are used in the overview illustrations and

refer to the numbers used in the product overview section

This symbol is intended to draw special attention to certain points

when handling the product.

Wireless data transfer

1.3 Product-dependent symbols

1.3.1 Symbols on the product

The following symbols are used on the product:

Rated speed under no load

Revolutions per minute

Direct current (DC)

Drilling without hammer action

1.4 Product information

Hilti products are designed for professional use and may be operated, ser-

viced and maintained only by trained, authorized personnel. This personnel

must be informed of any particular hazards that may be encountered. The

product and its ancillary equipment can present hazards if used incorrectly

by untrained personnel or if used not in accordance with the intended use.

The type designation and serial number are stated on the rating plate.

▶

Write down the serial number in the table below. You will be required to

state the product details when contacting Hilti Service or your local Hilti

organization to inquire about the product.

Product information

Drill/driver SF 2-A | SFD 2-A

Generation: 01

Serial no.:

1.5 Declaration of conformity

We declare, on our sole responsibility, that the product described here

complies with the applicable directives and standards. A copy of the

declaration issued by the certification department can be found at the end

of this documentation.

The technical documentation is filed here:

Printed: 07.01.2019 | Doc-Nr: PUB / 5174907 / 000 / 02

*2081399*

2081399 English 3

Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916

Kaufering, Germany

2 Safety

2.1 General power tool safety warnings

WARNING Read all safety warnings, instructions, illustrations and

specifications provided with this power tool. Failure to follow all instruc-

tions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded)

power tool or battery-operated (cordless) power tool.

Work area safety

▶ Keep work area clean and well lit. Cluttered or dark areas invite

accidents.

▶ Do not operate power tools in explosive atmospheres, such as in

the presence of flammable liquids, gases or dust. Power tools create

sparks which may ignite the dust or fumes.

▶ Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

Electrical safety

▶ Power tool plugs must match the outlet. Never modify the plug in any

way. Do not use any adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will reduce risk of electric

shock.

▶ Avoid body contact with earthed or grounded surfaces, such as

pipes, radiators, ranges and refrigerators. There is an increased risk of

electric shock if your body is earthed or grounded.

▶ Do not expose power tools to rain or wet conditions. Water entering a

power tool will increase the risk of electric shock.

▶ Do not abuse the cord. Never use the cord for carrying, pulling or

unplugging the power tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled cords increase the risk

of electric shock.

▶

When operating a power tool outdoors, use an extension cord suitable

for outdoor use. Use of a cord suitable for outdoor use reduces the risk

of electric shock.

▶ If operating a power tool in a damp location is unavoidable, use

a residual current device (RCD) protected supply. Use of an RCD

reduces the risk of electric shock.

Personal safety

▶ Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired

or under the influence of drugs, alcohol or medication. A moment

Printed: 07.01.2019 | Doc-Nr: PUB / 5174907 / 000 / 02

4 English 2081399

*2081399*

of inattention while operating power tools may result in serious personal

injury.

▶ Use personal protective equipment. Always wear eye protection.

Protective equipment such as a dust mask, non-skid safety shoes, hard

hat or hearing protection used for appropriate conditions will reduce

personal injuries.

▶ Prevent unintentional starting. Ensure the switch is in the off-position

before connecting to power source and/or battery pack, picking up

or carrying the tool. Carrying power tools with your finger on the switch

or energising power tools that have the switch on invites accidents.

▶ Remove any adjusting key or wrench before turning the power tool

on. A wrench or a key left attached to a rotating part of the power tool

may result in personal injury.

▶ Do not overreach. Keep proper footing and balance at all times. This

enables better control of the power tool in unexpected situations.

▶ Dress properly. Do not wear loose clothing or jewellery. Keep your

hair and clothing away from moving parts. Loose clothes, jewellery or

long hair can be caught in moving parts.

▶ If devices are provided for the connection of dust extraction and

collection facilities, ensure these are connected and properly used.

Use of dust collection can reduce dust-related hazards.

▶ Do not let familiarity gained from frequent use of tools allow you

to become complacent and ignore tool safety principles. A careless

action can cause severe injury within a fraction of a second.

Power tool use and care

▶ Do not force the power tool. Use the correct power tool for your

application. The correct power tool will do the job better and safer at the

rate for which it was designed.

▶ Do not use the power tool if the switch does not turn it on and off.

Any power tool that cannot be controlled with the switch is dangerous

and must be repaired.

▶ Disconnect the plug from the power source and/or remove the

battery pack, if detachable, from the power tool before making

any adjustments, changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting the power tool

accidentally.

▶ Store idle power tools out of the reach of children and do not

allow persons unfamiliar with the power tool or these instructions

to operate the power tool. Power tools are dangerous in the hands of

untrained users.

▶ Maintain power tools and accessories. Check for misalignment or

binding of moving parts, breakage of parts and any other condition

that may affect the power tool’s operation. If damaged, have the

Printed: 07.01.2019 | Doc-Nr: PUB / 5174907 / 000 / 02

*2081399*

2081399 English 5

power tool repaired before use. Many accidents are caused by poorly

maintained power tools.

▶ Keep cutting tools sharp and clean. Properly maintained cutting tools

with sharp cutting edges are less likely to bind and are easier to control.

▶ Use the power tool, accessories and tool bits etc. in accordance with

these instructions, taking into account the working conditions and

the work to be performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

▶ Keep handles and grasping surfaces dry, clean and free from oil and

grease. Slippery handles and grasping surfaces do not allow for safe

handling and control of the tool in unexpected situations.

Battery tool use and care

▶ Recharge only with the charger specified by the manufacturer. A

charger that is suitable for one type of battery pack may create a risk of

fire when used with another battery pack.

▶ Use power tools only with specifically designated battery packs. Use

of any other battery packs may create a risk of injury and fire.

▶ When battery pack is not in use, keep it away from other metal

objects, like paper clips, coins, keys, nails, screws or other small

metal objects, that can make a connection from one terminal to

another. Shorting the battery terminals together may cause burns or a

fire.

▶ Under abusive conditions, liquid may be ejected from the battery;

avoid contact. If contact accidentally occurs, flush with water. If

liquid contacts eyes, additionally seek medical help. Liquid ejected

from the battery may cause irritation or burns.

▶ Do not use a battery pack or tool that is damaged or modified.

Damaged or modified batteries may exhibit unpredictable behaviour

resulting in fire, explosion or risk of injury.

▶ Do not expose a battery pack or tool to fire or excessive temperature.

Exposure to fire or temperature above 265 °F may cause explosion.

▶ Follow all charging instructions and do not charge the battery pack

or tool outside the temperature range specified in the instructions.

Charging improperly or at temperatures outside the specified range may

damage the battery and increase the risk of fire.

Service

▶ Have your power tool serviced by a qualified repair person using only

identical replacement parts. This will ensure that the safety of the power

tool is maintained.

▶ Never service damaged battery packs. Service of battery packs should

only be performed by the manufacturer or authorized service providers.

Printed: 07.01.2019 | Doc-Nr: PUB / 5174907 / 000 / 02

6 English 2081399

*2081399*

2.2 Drill safety warnings

▶ Use auxiliary handle(s), if supplied with the tool. Loss of control can

cause personal injury.

▶ Hold power tool by insulated gripping surfaces, when performing an

operation where the cutting accessory may contact hidden wiring.

Cutting accessory contacting a "live" wire may make exposed metal parts

of the power tool "live" and could give the operator an electric shock.

2.3 Drill/driver safety warnings

▶ Hold power tool by insulated gripping surfaces, when performing an

operation where the fastener may contact hidden wiring. Fasteners

contacting a "live" wire may make exposed metal parts of the power tool

"live" and could give the operator an electric shock.

2.4 Additional safety instructions

Personal safety

▶ Tampering with or modification of the tool is not permitted.

▶ Keep the grips dry, clean and free from oil and grease.

▶ Improve the blood circulation in your fingers by relaxing your hands

and exercising your fingers during breaks between working.

▶ Do not look directly into the light source (LEDs) integrated in the

drill/driver and do not direct the light at other persons’ faces. This

presents a risk of dazzling or eye damage.

▶ Avoid touching rotating parts. Switch the power tool on only after

bringing it into position at the workpiece. Touching rotating parts,

especially rotating drill bits or other accessory tools, may lead to injury.

▶ Wear protective gloves. The drill/driver may get hot during use. There is

a risk of injury (cutting or burning) if the accessory tool is touched while

changing it.

▶ Activate the safety lock (forward/reverse selector switch in the middle

position) when changing accessory tools or batteries and before storage

or transportation of the power tool.

▶ The power tool is not intended for use by debilitated persons who

have received no special training. Keep the power tool out of reach

of children.

▶ Dust from materials, such as paint containing lead, some wood species,

concrete / masonry / stone containing silica, and minerals as well as

metal, may be harmful. Contact with or inhalation of the dust may cause

allergic reactions and/or respiratory or other diseases to the operator

or bystanders. Certain kinds of dust are classified as carcinogenic

such as oak and beech dust, especially in conjunction with additives for

wood conditioning (chromate, wood preservative). Material containing

asbestos may be handled only by specialists. Use a dust removal

Printed: 07.01.2019 | Doc-Nr: PUB / 5174907 / 000 / 02

*2081399*

2081399 English 7

system whenever possible. To achieve a high level of dust collection,

use a suitable vacuum cleaner. When indicated wear a respirator

appropriate for the type of dust generated. Ensure that the workplace

is well ventilated. Follow national requirements for the materials you

want to work with.

▶ Before beginning the work, check the hazard classification of the

dust that will be produced. Use an industrial vacuum cleaner with

an officially approved protection classification in compliance with

locally applicable dust protection regulations.

▶ Working on the material may cause it to splinter. Wear eye protection.

Flying fragments present a risk of injury to the body and eyes.

▶ Always hold the tool securely by the grip. If the accessory tool (e.g.

the drill bit) sticks and stalls, the power tool, due to its high torque, may

tend to rotate about its own axis in the direction opposite to that of the

accessory tool.

Use and care of electric tools

▶ Secure the workpiece. Use clamps or a vice to hold the workpiece

in position. The workpiece is thus held more securely than by hand and

both hands remain free to operate the power tool.

▶ Check that the accessory tools used are compatible with the chuck

system and that they are secured in the chuck correctly.

Use and care of battery-powered devices

▶ Check that the tool is switched off before inserting the battery.

Inserting a battery into an electric tool that is switched on can lead to

accidents.

▶ Do not expose batteries to high temperatures and keep them away

from fire. There is a risk of explosion.

▶ Do not disassemble, squash or incinerate batteries and do not subject

them to temperatures over 80°C (176°F). This presents a risk of fire,

explosion or injury through contact with caustic substances.

▶ Avoid ingress of moisture. Ingress of moisture may cause a short circuit,

resulting in burning injuries or fire.

▶ Observe the special guidelines applicable to the transport, storage

and use of Li-ion batteries.

▶ Avoid short circuiting the battery terminals. Check that the battery

terminals and the terminals in the power tool are free from foreign

objects before inserting the battery in the tool. Short circuiting the

battery terminals presents a risk of fire, explosion and chemical burns.

▶ Do not continue to use or attempt to charge damaged batteries (e.g.

batteries with cracks, broken parts, bent or pushed-in / pulled-out

contacts).

▶ If the battery is too hot to touch it may be defective. In this case,

place the power tool in a non-flammable location, well away from

flammable materials, where it can be kept under observation and

Printed: 07.01.2019 | Doc-Nr: PUB / 5174907 / 000 / 02

8 English 2081399

*2081399*

allowed to cool down. Contact Hilti Service after the battery has

cooled down.

Electrical safety

▶ Before beginning work, check the working area (e.g. using a metal

detector) to ensure that no concealed electric cables or gas and

water pipes are present. External metal parts of the power tool may

become live, for example, when an electric cable is damaged accidentally.

This presents a serious risk of electric shock.

3 Description

3.1 Intended use

The product described is a hand-held cordless drill / driver for driving and

removing screws, drilling in metal, wood and plastic.

Hilti products are designed for professional use and may be operated, ser-

viced and maintained only by trained, authorized personnel. This personnel

must be informed of any particular hazards that may be encountered. The

hammer drill/driver and its ancillary equipment may present hazards when

used incorrectly by untrained personnel or when used not as directed.

▶ Do not use the battery as a power source for other unspecified power

tools or appliances.

▶ Observe the national health and safety requirements.

▶ To reduce the risk of injury, use only genuine Hilti tools and accessories.

▶ Use only Hilti LiIon batteries of the B 12 series with this product.

Make sure that the outer surfaces of the battery are clean and dry

before inserting the battery in an approved battery charger.

Read the operating instructions for the charger for further information

about the charging procedure.

▶ Use only Hilti battery chargers from the C4/12-50 series with these

batteries.

3.2 Items supplied

Drill / driver, operating instructions.

Other system products approved for use with this product can be found

at your local Hilti Store or online at: www.hilti.group.

Printed: 07.01.2019 | Doc-Nr: PUB / 5174907 / 000 / 02

*2081399*

2081399 English 9

4 Technical data

4.1 Technical data

SF 2A SFD 2-A

Rated voltage

10.8 V 10.8 V

Weight

1.1 kg

(2.4 lb)

1 kg

(2 lb)

Speed in 1st gear

0 /min …

400 /min

0 /min …

400 /min

Speed in 2nd gear

0 /min …

1,500 /min

0 /min …

1,500 /min

Torque

0 Nm …

3.5 Nm

0 Nm …

3.5 Nm

Torque (drill symbol)

12 Nm 12 Nm

4.2 Battery

Battery operating voltage

10.8 V

Ambient temperature

−17 ℃ … 60 ℃

(1 ℉ … 140 ℉)

Storage temperature

−20 ℃ … 40 ℃

(−4 ℉ … 104 ℉)

Charging temperature

−10 ℃ … 60 ℃

(14 ℉ … 140 ℉)

5 Operation

5.1 Inserting/removing the battery 1

CAUTION

Risk of injury. The drill/driver may start inadvertently.

▶ Before fitting the battery, check that the drill/driver is switched off and

that the switch safety lock is activated.

CAUTION

Electrical hazard. Dirty contacts may cause a short circuit.

▶ Before inserting the battery, check to ensure that the battery terminals

and the contacts in the drill/driver are free from foreign objects.

CAUTION

Risk of injury. If the battery is not fitted correctly it may drop out and fall.

▶ Check that the battery is securely seated in the tool so that it cannot drop

out and fall, thereby presenting a hazard to other persons.

Printed: 07.01.2019 | Doc-Nr: PUB / 5174907 / 000 / 02

10 English 2081399

*2081399*

1. To insert, push the battery into the tool from the front until it engages with

an audible click.

2. To remove, press and hold down the release button and pull the battery

forward and out of the tool.

5.2 Fitting the belt hook (optional) 2

WARNING

Risk of injury. A falling power tool may present a risk of injury to yourself

and others.

▶ Check that the belt hook is fitted securely before beginning work.

The belt hook allows the power tool to be attached to a belt worn by

the operator. The belt hook can be fitted to allow attachment on the left

or right side of the body.

▶ Fit the belt hook.

5.3 Setting the torque

▶ Set the desired torque.

The torque is limited only when the power tool is set to screwdriving

mode .

5.4 Selecting the gear 3

▶ Select the desired gear by adjusting the two gear selector switches.

5.5 Setting forward or reverse rotation 4

An interlock prevents switching while the motor is running.

The control switch is locked when the forward/reverse switch is in the

middle position (safety lock).

▶ Set the forward/reverse switch to the desired direction of rotation.

5.6 Inserting/removing the accessory tool 5

1. Set the forward/reverse switch to the middle position or remove the

battery from the power tool.

Printed: 07.01.2019 | Doc-Nr: PUB / 5174907 / 000 / 02

*2081399*

2081399 English 11

2. If the following equipment exists, also take this action:

SF 2A

▶ Open the keyless chuck by turning it counter-clockwise.

▶ Insert the accessory tool into the chuck and turn the keyless chuck

clockwise until it is tight.

▶ Check that the bit is held securely.

▶ To remove the accessory tool, re-open the keyless chuck.

3. If the following equipment exists, also take this action:

SFD 2-A

▶ Push the locking sleeve on the hex. socket forward and hold it securely

in this position.

▶ Slide the accessory tool into the hex socket as far as it will go and

release the locking sleeve.

▶ Check that the bit is held securely.

▶ To remove the accessory tool, push the locking sleeve on the hex

socket forward and hold it in this position.

▶ Remove the accessory tool from the hex socket and release the locking

sleeve.

5.7 Switching on

▶ Press the control switch.

Speed can be controlled steplessly right up to maximum by varying

how far the control switch is pressed in.

5.8 Switching off

▶ Release the control switch.

5.9 Screwdriving

1. Set the torque and operating mode selector ring to the required torque.

2. Set the forward/reverse switch to the desired direction of rotation.

5.10 Drilling

1.

Set the torque and operating mode selector ring to the symbol.

2. Set the forward/reverse switch to the “forward” position.

6 Care and maintenance of cordless tools

WARNING

Risk of injury with battery inserted !

▶ Always remove the battery before carrying out care and maintenance

tasks!

Printed: 07.01.2019 | Doc-Nr: PUB / 5174907 / 000 / 02

12 English 2081399

*2081399*

Care and maintenance of the tool

• Carefully remove stubborn dirt.

• Clean the air vents carefully with a dry brush.

• Use only a slightly damp cloth to clean the casing. Do not use cleaning

agents containing silicone as these can attack the plastic parts.

Care of the Liion batteries

• Keep the battery free from oil and grease.

• Use only a slightly damp cloth to clean the casing. Do not use cleaning

agents containing silicone as these may attack the plastic parts.

• Avoid ingress of moisture.

Maintenance

• Check all visible parts and controls for signs of damage at regular intervals

and make sure that they all function correctly.

• Do not operate the cordless tool if signs of damage are found or if parts

malfunction. Have the tool repaired by Hilti Service immediately.

• After cleaning and maintenance, fit all guards or protective devices and

check that they function correctly.

To help ensure safe and reliable operation, use only genuine Hilti spare

parts and consumables. Spare parts, consumables and accessories

approved by Hilti for use with the product can be found at your local

Hilti Store or online at: www.hilti.group | USA: www.hilti.com

7 Transport and storage of cordless tools

Transport

CAUTION

Accidental starting during transport !

▶ Always transport your products with the batteries removed!

▶ Remove the battery.

▶ Transport the tool and batteries individually packaged.

▶ Never transport batteries in bulk form (loose, unprotected).

▶ Check the tool and batteries for damage before use after long periods of

transport.

Storage

CAUTION

Accidental damage caused by defective or leaking batteries !

▶ Always store your products with the batteries removed!

▶ Store the tool and batteries in a place that is as cool and dry as possible.

▶ Never store batteries in direct sunlight, on heating units or behind a

window pane.

▶ Store the tool and batteries in a place where they cannot be accessed by

children or unauthorized persons.

Printed: 07.01.2019 | Doc-Nr: PUB / 5174907 / 000 / 02

*2081399*

2081399 English 13

▶ Check the tool and batteries for damage before use after long periods of

storage.

8 Troubleshooting

8.1 Troubleshooting

If the trouble you are experiencing is not listed in this table or you are unable

to remedy the problem by yourself, please contact Hilti Service.

8.1.1 Troubleshooting

Trouble or fault Possible cause Action to be taken

The power tool does

not work.

The battery is not fully

inserted.

▶ Push the battery in

until it engages with

an audible double

click.

Low battery. ▶ Change the battery

and charge the empty

battery.

The on/off button

cannot be pressed,

i.e. the button is

locked.

The forward/reverse

selector switch is in the

middle position.

▶ Push the

forward/reverse

switch to the left or

right.

The battery runs

down more quickly

than usual.

Very low ambient tem-

perature.

▶ Allow the battery to

warm up slowly to

room temperature.

The battery does

not engage with an

audible double click.

The retaining lugs on the

battery are dirty.

▶ Clean the retaining

lugs and push the

battery in until it

engages. Contact

Hilti Service if the

problem persists.

The tool or battery

gets very hot.

The tool is overloaded

(application limits ex-

ceeded).

▶ Pay attention to the

power and perfor-

mance rating of the

product before using

it, i.e check its suitabil-

ity for the job on hand.

See the “Technical

data” section.

8.2 Disposal

Most of the materials from which Hilti tools and appliances are manu-

factured can be recycled. The materials must be correctly separated before

Printed: 07.01.2019 | Doc-Nr: PUB / 5174907 / 000 / 02

14 English 2081399

*2081399*

they can be recycled. In many countries, your old tools, machines or appli-

ances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti

representative for further information.

Battery disposal

Improper disposal of batteries can result in health hazards from leaking

gases or fluids.

▶ DO NOT send batteries through the mail!

▶ Cover the terminals with a non-conductive material (such as electrical

tape) to prevent short circuiting.

▶ Dispose of your battery out of the reach of children.

▶ Dispose of the battery at your Hilti Store, or consult your local govern-

mental garbage disposal or public health and safety resources for disposal

instructions.

▶ Do not dispose of power tools, electronic equipment or batteries as

household waste!

9 Manufacturer’s warranty

▶ Please contact your local Hilti representative if you have questions about

the warranty conditions.

Printed: 07.01.2019 | Doc-Nr: PUB / 5174907 / 000 / 02

*2081399*

2081399 Français 15

1 Indications relatives à la documentation

1.1 À propos de cette documentation

• Lire intégralement la présente documentation avant la mise en service.

C'est la condition préalablement requise pour assurer la sécurité du travail

et un maniement sans perturbations.

• Bien respecter les consignes de sécurité et les avertissements de la

présente documentation ainsi que celles figurant sur le produit.

• Toujours conserver le mode d'emploi à proximité du produit et uniquement

le transmettre à des tiers avec ce mode d'emploi.

1.2 Explication des symboles

1.2.1 Avertissements

Les avertissements attirent l'attention sur des dangers liés à l'utilisation du

produit. Les termes de signalisation suivants sont utilisés :

DANGER

DANGER !

▶ Pour un danger imminent qui peut entraîner de graves blessures corpo-

relles ou la mort.

AVERTISSEMENT

AVERTISSEMENT !

▶ Pour un danger potentiel qui peut entraîner de graves blessures corpo-

relles ou la mort.

ATTENTION

ATTENTION !

▶ Pour attirer l'attention sur une situation pouvant présenter des dangers

entraînant des blessures corporelles légères ou des dégâts matériels.

1.2.2 Symboles dans la documentation

Les symboles suivants sont utilisés dans la présente documentation :

Lire le mode d'emploi avant d'utiliser l'appareil

Pour des conseils d'utilisation et autres informations utiles

Maniement des matériaux recyclables

Ne pas jeter les appareils électriques et les accus dans les ordures

ménagères

1.2.3 Symboles dans les illustrations

Les symboles suivants sont utilisés dans les illustrations :

Printed: 07.01.2019 | Doc-Nr: PUB / 5174907 / 000 / 02

16 Français 2081399

*2081399*

Ces chiffres renvoient à l'illustration correspondante au début du

présent mode d'emploi

La numérotation détermine la séquence des étapes de travail dans

l'image et peut se différencier de celles des étapes de travail dans le

texte

Les numéros de position sont utilisés dans l'illustration Vue d’en-

semble et renvoient aux numéros des légendes dans la section Vue

d'ensemble du produit

Ce signe doit inviter à manier le produit en faisant particulièrement

attention.

Transmission de données sans fil

1.3 Symboles spécifiques au produit

1.3.1 Symboles sur le produit

Les symboles suivants sont utilisés sur le produit :

Vitesse nominale à vide

Tours par minute

Courant continu

Perçage sans percussion

1.4 Informations produit

Les produits Hilti sont conçus pour les utilisateurs professionnels et ne

doivent être utilisés, entretenus et réparés que par un personnel agréé et

formé à cet effet. Ce personnel doit être au courant des dangers inhérents

à l'utilisation de l'appareil. Le produit et ses accessoires peuvent s'avérer

dangereux s'ils sont utilisés de manière incorrecte par un personnel non

qualifié ou de manière non conforme à l'usage prévu.

La désignation du modèle et le numéro de série figurent sur sa plaque

signalétique.

▶ Inscrivez le numéro de série dans le tableau suivant. Les informations

produit vous seront demandées lorsque vous contactez nos revendeurs

ou services après-vente.

Caractéristiques produit

Visseuse-perceuse SF 2-A | SFD 2-A

Génération : 01

N° de série :

1.5 Déclaration de conformité

Nous déclarons sous notre seule et unique responsabilité que le produit

décrit ici est conforme aux directives et normes en vigueur. Une copie de

Printed: 07.01.2019 | Doc-Nr: PUB / 5174907 / 000 / 02

La page charge ...

Hilti SF/SFD 2-A Mode d'emploi

Hilti SF/SFD 2-A Mode d'emploi

dans d''autres langues

Documents connexes