Wacker Neuson LTN8K-V S Manuel utilisateur

Operator’s Manual

Notice d'emploi

Light Tower

Tour d’éclairage

Type LTN 6K-V, LTN 6K-VS, LTN 8K-V, LTN

8K-VS, LTN 6L-VS (60 Hz)

Document 5200004276

Date 1115

Version 03

Language EN-FR

5200004276

LTN 6K-V, LTN 6K-VS

LTN 8K-V, LTN 8K-VS

LTN 6L-VS 60 Hz

Copyright notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the

machine. Any other type of reproduction is prohibited without express

written permission from Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker

Neuson Production Americas LLC represents an infringement of valid

copyrights. Violators will be prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their

respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original instructions

This Operator’s Manual presents the original instructions. The original

language of this Operator’s Manual is American English.

LTN Foreword

wc_tx003092gb.fm 3

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

Machines

covered in

this manual

Machine

identification

A nameplate listing the model number, item number, revision number, and serial

number is attached to this machine. The location of the nameplate is shown above.

Serial number

(S/N)

For future reference, record the serial number in the space provided below. You will

need the serial number when requesting parts or service for this machine.

Machine

documentation

 From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 If you are missing either of these documents, please contact Wacker Neuson to

order a replacement or visit www.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Machine Item Number

LTN 6K-V 5200002722, 5200002726

LTN 8K-V 5200002727, 5200002728

LTN 6K-V S 5200018537, 5200018550, 5200018553

LTN 8K-V S 5200018538, 5200018551, 5200018554

LTN 6L-V S 5200018536, 5200018539, 5200018552

wc_gr010093

Serial Number:

Foreword LTN

4 wc_tx003092gb.fm

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and main-

tain the above Wacker Neuson model(s). For your own safety and to reduce the

risk of injury, carefully read, understand, and observe all instructions described

in this manual.

 Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change

any portion of this information without notice.

 The illustrations, parts, and procedures in this manual refer to Wacker Neuson

factory-installed components. Your machine may vary depending on the

requirements of your specific region.

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and

modifications. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

 Approved modifications are those performed by an authorized Wacker Neu-

son service center according to written instructions published by Wacker Neu-

son.

 Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following

consequences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

CALIFORNIA

Proposition

65 Warning

Combustion exhaust, some of its constituents, and certain vehicle components

contain or emit chemicals known to the State of California to cause cancer and

birth defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental dis-

charge of sparks or flames from the engine exhaust. Spark arresters are qualified

and rated by the United States Forest Service for this purpose. In order to comply

with local laws regarding spark arresters, consult the engine distributor or the local

Health and Safety Administrator.

Table of Contents

LTN

wc_bo5200004275_03TOC.fm

5

Foreword 3

1 Safety Information 9

1.1 Signal Words Used in this Manual ....................................................... 9

1.2 Machine Description and Intended Use ............................................. 10

1.3 Safety Guidelines for Operating the Machine ..................................... 11

1.4 Service Safety .................................................................................... 14

1.5 Operator Safety while Using Internal Combustion Engines ............... 16

1.6 Safety Guidelines for Lifting and Transporting the Machine ............... 17

1.7 Safety Guidelines for Towing the Machine ......................................... 18

1.8 Reporting Safety Defects ................................................................... 19

2 Labels 20

2.1 Label Locations .................................................................................. 20

2.2 Label Meanings .................................................................................. 22

3 Lifting and Transporting 31

3.1 Lifting the Machine ............................................................................. 31

3.2 Preparing the Machine for Transport on a Truck or Trailer ................ 32

3.3 Preparing the Machine for Towing ..................................................... 33

3.4 Towing the Machine ........................................................................... 34

4 Operation 35

4.1 Preparing the Machine for First Use ................................................... 35

4.2 Generator Derating ............................................................................. 35

4.3 Positioning the Machine ..................................................................... 36

4.4 Ground Connection ............................................................................ 37

4.5 Leveling Trailer ................................................................................... 38

4.6 Refueling the Machine ........................................................................ 39

4.7 Aiming the Lights - LTN-V .................................................................. 40

4.8 Control Panels .................................................................................... 43

4.9 Control Panels - LTN 6L-VS ............................................................... 44

4.10 Before Starting ................................................................................... 45

4.11 Starting the Machine - LTN 6K-V, LTN 8K-V ...................................... 46

4.12 Starting the Machine - LTN 6L ........................................................... 47

4.13 Operating the Lights ........................................................................... 48

4.14 Raising the Tower - LTN -V ................................................................ 49

4.15 Manually Rotating the Mast ................................................................ 50

Table of Contents

LTN

wc_bo5200004275_03TOC.fm

6

4.16 Lowering the Tower .............................................................................51

4.17 Automatic Shutdown ...........................................................................52

4.18 Stopping the Machine - LTN 6K/8K-V .................................................52

4.19 Stopping the Machine - LTN 6L-V .......................................................53

4.20 Emergency Shutdown Procedure ........................................................54

4.21 Using the Convenience Receptacles - 60 Hz ......................................55

5 Factory-Installed Options 56

5.1 Engine Block Heater ............................................................................56

5.2 Battery Blanket ....................................................................................56

5.3 Oil Pan Heater .....................................................................................57

5.4 RCBO Circuit Breaker .........................................................................57

5.5 LED Lights ...........................................................................................58

6 Maintenance 59

6.1 Preparing for Maintenance ..................................................................59

6.2 Periodic Maintenance Schedule ..........................................................60

6.3 Cleaning the Machine ..........................................................................61

6.4 Inspecting the Machine .......................................................................62

6.5 Checking the Engine Oil ......................................................................63

6.6 Changing the Engine Oil .....................................................................64

6.7 Checking the Engine Coolant Level ....................................................65

6.8 Flushing the Radiator ..........................................................................66

6.9 Cleaning the Air Filter Element ............................................................68

6.10 Maintaining the Battery ........................................................................69

6.11 Checking Fan Belt Tension .................................................................70

6.12 Checking Radiator Hoses ....................................................................71

6.13 Performing Coolant Solution Analysis .................................................72

6.14 Testing the Cooling System Pressure .................................................73

6.15 Removing and Replacing Lamps ........................................................75

6.16 Long-Term Storage .............................................................................77

6.17 Machine Disposal / Decommissioning .................................................78

7 Engine Maintenance: Kubota (T4f) 80

8 Engine Maintenance: Kohler (T4f) 84

9 Troubleshooting 88

Table of Contents

LTN

wc_bo5200004275_03TOC.fm

7

10 Technical Data 90

10.1 Engine - Kubota .................................................................................. 90

10.2 Engine - Kohler ................................................................................... 91

10.3 Generator ........................................................................................... 92

10.4 Machine .............................................................................................. 93

10.5 Radiation Compliance ........................................................................ 94

10.6 Dimensions - LTN 6K-V, LTN 8K-V .................................................... 94

10.7 Dimensions - LTN 6K-VS, LTN 8K-VS, LTN 6L-VS ........................... 94

11 Schematics 95

11.1 LTN 8K-V Lighting Schematic ............................................................ 95

11.2 Components ....................................................................................... 96

11.3 LTN 6K-V Lighting Schematic ............................................................ 97

11.4 Components ....................................................................................... 98

11.5 Generator Capacitor Excitation Schematic ........................................ 99

11.6 Engine Wiring ................................................................................... 100

11.7 Components ..................................................................................... 101

11.8 Hydraulic Schematic - LTN 6K-V, LTN 8K-V .................................... 102

11.9 Hydraulic Schematic- LTN 6K-VS, LTN 8K-VS ................................ 103

11.10 Trailer Wiring .................................................................................... 104

Table of Contents

LTN

wc_bo5200004275_03TOC.fm

8

wc_si000704gb.fm

9

LTN Safety Information

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury,

damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f To avoid death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f To avoid possible death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f To avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

wc_si000704gb.fm

10

Safety Information LTN

1.2 Machine Description and Intended Use

Machine

description

This machine is a mobile, trailer-mounted light tower. The Wacker Neuson Light

Tower consists of a trailer with a cabinet containing a diesel engine, a fuel tank, a

control panel, and an electric alternator. A telescoping tower with four metal halide

lights is vertically mounted to the top of the machine. A hydraulic cylinder,

combined with a cable and pulley system, raises and lowers the telescoping tower.

As the engine runs, the generator converts mechanical energy into electric power.

The metal halide lights run off this power. Receptacle(s) are also provided to power

auxiliary loads. The operator uses the control panel to operate and monitor the

machine.

Intended use

This machine is intended for the illumination of outdoor areas. This machine is also

intended for the purpose of supplying electrical power to connected loads. Refer to

the machine specifications for the output voltage and frequency, and for the

maximum output power limit of this Light Tower.

This machine has been designed and built strictly for the intended use described

above. Using the machine for any other purpose could permanently damage the

machine or seriously injure the operator or other persons in the area. Machine

damage caused by misuse is not covered under warranty. The following are some

examples of misuse:

 Connecting a load that has voltage and frequency requirements that are

incompatible with the machine output

 Overloading the machine with a device that draws excessive power during

either continuous running or startup

 Operating the machine in a manner that is inconsistent with all federal, state,

and local codes and regulations

 Using the machine as a ladder, support, or work surface

 Using the machine to carry or transport passengers or equipment

 Using the machine as a hoist, or hanging items from the tower

 Operating the machine outside of factory specifications

 Operating the machine in a manner inconsistent with all warnings found on the

machine and in the Operator’s Manual

This machine has been designed and built in accordance with the latest global

safety standards. It has been carefully engineered to eliminate hazards as far as

practicable and to increase operator safety through protective guards and labeling.

However, some risks may remain even after protective measures have been taken.

They are called residual risks. On this machine, they may include exposure to:

 Heat, noise, exhaust, and carbon monoxide from the engine

 Heat from the lights

 Ultraviolet radiation from the lights

 Fire hazards from improper refueling techniques

 Fuel and its fumes

 Electric shock and arc flash

 Personal injury from improper lifting the trailer tongue

wc_si000704gb.fm

11

LTN Safety Information

 Glare from lights (lights may blind drivers of nearby motor vehicles if the lights

are incorrectly positioned)

 Typical hazards related to towing a trailer on roads and highways

To protect yourself and others, make sure you thoroughly read and understand the

safety information presented in this manual before operating the machine.

1.3 Safety Guidelines for Operating the Machine

Operator

training

Before operating the machine:

 Read and understand the operating instructions contained in all manuals

delivered with the machine.

 Familiarize yourself with the location and proper use of all controls and safety

devices.

 Contact Wacker Neuson for additional training if necessary.

When operating this machine:

 Do not allow improperly trained people to operate the machine. People

operating the machine must be familiar with the potential risks and hazards

associated with it.

Operator

qualifications

Only trained personnel are permitted to start, operate, and shut down the machine.

They also must meet the following qualifications:

 have received instruction on how to properly use the machine

 are familiar with required safety devices

The machine must not be accessed or operated by:

 children

 people impaired by alcohol or drugs

Application

area

Be aware of the application area.

 Keep unauthorized personnel, children, and pets away from the machine.

 Remain aware of changing positions and the movement of other equipment and

personnel in the application area/job site.

Be aware of the application area.

 Do not operate the machine in areas that contain flammable objects, fuels, or

products that produce flammable vapors.

Safety

devices,

controls, and

attachments

Only operate the machine when:

 All safety devices and guards are in place and in working order.

 All controls operate correctly.

 The machine is set up correctly according to the instructions in the Operator’s

Manual.

 The machine is clean.

 The machine’s labels are legible.

To ensure safe operation of the machine:

wc_si000704gb.fm

12

Safety Information LTN

 Do not operate the machine if any safety devices or guards are missing or

inoperative.

 Do not modify or defeat the safety devices.

 Only use accessories or attachments that are approved by Wacker Neuson.

Safe

operating

practices

When operating this machine:

 Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

When operating this machine:

 Do not operate a machine in need of repair.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while operating this

machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

Before

Starting

 Be sure the machine is on a firm, level surface and will not tip, roll, slide, or fall

while operating.

 Never connect machine to other power sources, such as supply mains of power

companies.

 Never use the machine if the insulation on the electrical cord is cut or worn

through.

 Never raise the tower or operate the machine in high winds.

 The tower extends up to 8.7 m (28.54 ft.). Make sure the area above the trailer

is open and clear of overhead wires and obstructions.

Operation

 Keep the area under and around the lights clear of people while raising and

lowering the tower.

 Do not move the Light Tower while it is operating.

After Use

 Stop the engine when the machine is not being operated.

 Close the fuel valve on engines equipped with one when machine is not being

operated.

 Ensure that the machine will not tip over, roll, slide, or fall when not being

operated.

 Store the machine properly when it is not being used. The machine should be

stored in a clean, dry location out of the reach of children.

 Lower the tower when not in use, or if high winds or electrical storms are

expected in the area.

 The lamps become extremely hot in use! Allow the lamp and fixture to cool

10‚Äì15 minutes before handling.

 Lamp Safety

wc_si000704gb.fm

13

LTN Safety Information

Description

The lamps provided with your Light Tower are electric discharge lamps. They are

designed for use with metal halide ballasts only, and require time to reach full

brightness on initial startup and after a power interruption. These lamps comply

with FDA regulation performance standards 21 CFR 1040-30.

Operating

safety

 Replace damaged lamps according to the instructions in section Removing /

Replacing Lamps.

 Alternative lamps that automatically extinguish when the outer envelope is

broken or punctured are commercially available.

WARNING

Personal injury hazard. Broken or punctured lamps can cause serious skin burns

and eye inflammation from shortwave ultraviolet radiation.

f Do not operate the Light Tower if a lamp is damaged.

f Replace damaged lamps immediately.

wc_si000704gb.fm

14

Safety Information LTN

1.4 Service Safety

Service

training

Before servicing or maintaining the machine:

 Read and understand the instructions contained in all manuals delivered with

the machine.

 Familiarize yourself with the location and proper use of all controls and safety

devices.

 Only trained personnel shall troubleshoot or repair problems occurring with the

machine.

 Contact Wacker Neuson for additional training if necessary.

When servicing or maintaining this machine:

 Do not allow improperly trained people to service or maintain the machine.

Personnel servicing or maintaining the machine must be familiar with the

associated potential risks and hazards.

Precautions

Follow the precautions below when servicing or maintaining the machine.

 Read and understand the service procedures before performing any service to

the machine.

 All adjustments and repairs must be completed before operating the machine.

Do not operate the machine with a known problem or deficiency.

 All repairs and adjustments shall be completed by a qualified technician.

 Turn off the machine before performing maintenance or making repairs.

 Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

 Re-install the safety devices and guards after repair and maintenance

procedures are complete.

Machine

modifications

When servicing or maintaining the machine:

 Use only accessories/attachments that are approved by Wacker Neuson.

When servicing or maintaining the machine:

 Do not defeat safety devices.

 Do not modify the machine without the express written approval of Wacker

Neuson.

Replacing

parts and

labels

 Replace worn or damaged components.

 Replace all missing and hard-to-read labels.

 When replacing electrical components, use components that are identical in

rating and performance to the original components.

 When replacement parts are required for this machine, use only Wacker

Neuson replacement parts or those parts equivalent to the original in all types of

specifications, such as physical dimensions, type, strength, and material.

wc_si000704gb.fm

15

LTN Safety Information

Cleaning

When cleaning and servicing the machine:

 Keep the machine clean and free of debris such as leaves, paper, cartons, etc.

 Keep the labels legible.

When cleaning the machine:

 Do not clean the machine while it is running.

 Never use gasoline or other types of fuels or flammable solvents to clean the

machine. Fumes from fuels and solvents can become explosive.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while servicing or

maintaining this machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

In addition, before servicing or maintaining the machine:

 Tie back long hair.

 Remove all jewelry (including rings).

 Before servicing the Light Tower, make sure the engine start switch is turned to

the OFF position, the circuit breakers are open (off), and the negative terminal

on battery is disconnected. Do not perform even routine service (oil/filter

changes, cleaning, etc.) unless all electrical components are shut down.

 Always turn off light circuit breakers and shut down engine before disconnecting

light fixtures or changing light bulbs.

wc_si000704gb.fm

16

Safety Information LTN

1.5 Operator Safety while Using Internal Combustion Engines

Operating

safety

When running the engine:

 Keep the area around exhaust pipe free of flammable materials.

 Check the fuel lines and the fuel tank for leaks and cracks before starting the

engine. Do not run the machine if fuel leaks are present or the fuel lines are

loose.

When running the engine:

 Do not smoke while operating the machine.

 Do not run the engine near sparks or open flames.

 Do not touch the engine or muffler while the engine is running or immediately

after it has been turned off.

 Do not operate a machine when its fuel cap is loose or missing.

 Do not start the engine if fuel has spilled or a fuel odor is present. Move the

machine away from the spill and wipe the machine dry before starting.

Refueling

safety

When refueling the engine:

 Clean up any spilled fuel immediately.

 Refill the fuel tank in a well-ventilated area.

 Replace the fuel tank cap after refueling.

 Use suitable tools for refueling (for example, a fuel hose or funnel).

When refueling the engine:

 Do not smoke.

 Do not refuel a hot or running engine.

 Do not refuel the engine near sparks or open flames.

WARNING

Internal combustion engines present special hazards during operation and fueling.

Failure to follow the warnings and safety standards could result in severe injury or

death.

f Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Exhaust gas from the engine contains carbon monoxide, a deadly poison.

Exposure to carbon monoxide can kill you in minutes.

f NEVER operate the machine inside an enclosed area, such as a tunnel, unless

adequate ventilation is provided through such items as exhaust fans or hoses.

wc_si000704gb.fm

17

LTN Safety Information

1.6 Safety Guidelines for Lifting and Transporting the Machine

When lifting the machine:

 Make sure slings, chains, hooks, ramps, jacks, forklifts, cranes, hoists, and any

other type of lifting device used is attached securely and has enough weight-

bearing capacity to lift or hold the machine safely. See section Technical Data

for machine weight.

 Remain aware of the location of other people when lifting the machine.

 Only use the lifting points and tie-downs described in the Operator’s Manual.

 Make sure the transporting vehicle has sufficient load capacity and platform size

to safely transport the machine.

To reduce the possibility of injury:

 Do not stand under the machine while it is being lifted or moved.

 Do not get onto the machine while it is being lifted or moved.

wc_si000704gb.fm

18

Safety Information LTN

1.7 Safety Guidelines for Towing the Machine

When towing the machine:

 Do not tow the machine if the towing vehicle’s hitch or the trailer’s coupler are

damaged.

 Do not tow the machine if any of the trailer’s lug nuts are missing.

 Do not tow the machine if the trailer’s tires have less than 1.5 mm (1/16 inch) of

tread.

 Do not tow the machine unless the trailer’s brakes are functioning properly.

 Do not exceed the trailer manufacturer’s speed limitations.

When towing the machine:

 Only tow the machine when the trailer’s lug nuts are properly torqued.

 Only tow the machine when the trailer’s tires are properly inflated.

 Only tow the machine when all trailer lights are functioning correctly.

 Only tow the machine when the trailer’s safety chains are connected to the

towing vehicle in a crisscross pattern.

 Maintain extra distance between the towing vehicle and other vehicles.

 Avoid soft shoulders, curbs, and sudden lane changes.

 Abide by all licensing requirements for your area.

If you have not driven a towing vehicle with trailer before, practice turning,

stopping, and backing up the towing vehicle with trailer in an area away from traffic.

Only drive the towing vehicle with trailer when you are confident in your ability to do

so.

WARNING

Risk of severe injury or death. Improper trailer condition and towing technique can

lead to an accident.

f Obey the trailer manufacturer’s instructions and the instructions below to reduce

the risk of an accident.

wc_si000704gb.fm

19

LTN Safety Information

1.8 Reporting Safety Defects

If you believe your trailer has a defect which could cause a crash or could cause

injury or death, you should immediately inform the National Highway Traffic Safety

Administration (NHTSA) in addition to notifying Wacker Neuson.

If NHTSA receives similar complaints, it may open an investigation; and if it finds

that a safety defect exists in a group of trailers, it may order a recall and remedy

campaign. However, NHTSA cannot become involved in individual problems

between you, your dealer, or Wacker Neuson.

To contact NHTSA, you may either contact the Vehicle Safety Hotline toll-free at

1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safercar.gov; or write to:

Administrator

NHTSA

1200 New Jersey Avenue S.E.

Washington, DC 20590

You can also obtain other information about your motor vehicle safety from

http://www.safercar.gov

Labels LTN

20 wc_si000705gb.fm

2 Labels

2.1 Label Locations

wc_gr009301

A

B

R

C

S

WH

H

X

Y

D

E

F

G

HIJK

L

Q

P

O

N

M

La page charge ...

Wacker Neuson LTN8K-V S Manuel utilisateur

Ce manuel convient également à

Wacker Neuson LTN8K-V S Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents