Bosch Benchmark HEIP056U Guide d'installation

Electric and Induction Ranges

Installation Instructions

Slide-In Ranges

HEI8056C, HEI8056U, HEIP056C, HEIP056U, HIIP056C,

HIIP056U, HII8056C, HII8056U, HII8046C, HII8046U,

HEI8046C, HEI8046U

Table of Contents

Questions?

1-800-944-2904

www.bosch-home.com/us

We look forward to hearing from you!

This Bosch Appliance is made by

BSH Home Appliances Corporation

1901 Main Street, Suite 600

Irvine, CA 92614

Safety Definitions . . . . . . . . . . . . . . . 1

Safety . . . . . . . . . . . . . . . . . . . . . . . . . 1

Preparation . . . . . . . . . . . . . . . . . . . . 3

Before You Begin . . . . . . . . . . . . . . . . . . . . . 3

Tools and Parts Needed . . . . . . . . . . . . . . . . 3

Parts Included . . . . . . . . . . . . . . . . . . . . . . . . 3

Additional Parts Needed for Hard-Wired

Installations . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Remove Packaging . . . . . . . . . . . . . . . . . . . . 3

Installation Checklist . . . . . . . . . . . . . . . . . . 3

General Information . . . . . . . . . . . . . . . . . . . 4

Overall Dimensions . . . . . . . . . . . . . . . . . . . . 4

Location Level and Plumb . . . . . . . . . . . . . . . 4

Installation Hints . . . . . . . . . . . . . . . . . . . . . . 4

Electrical Requirements . . . . . . . . . . . . . . . . . 4

Cabinet Requirements . . . . . . . . . . . 5

Install Ventilation . . . . . . . . . . . . . . . . . . . . . . 5

Required Clearance . . . . . . . . . . . . . . . . . . . . 5

Prepare Walls and Floor . . . . . . . . . . . . . . . . 6

Countertop Requirements . . . . . . . . . . . . . . . 6

Installation Procedure . . . . . . . . . . . 7

Installation of the Anti-Tip Bracket . . . . . . 7

Electrical Connection . . . . . . . . . . . . . . . . . 7

Connect Flexible Conduit . . . . . . . . . . . . . . . 10

Complete the installation . . . . . . . . . . . . . . . 11

Removing the Oven Door . . . . . . . . . . . . . . 13

Replacing the Oven Door . . . . . . . . . . . . . . 14

Removing the Warming Drawer . . . . . . . . . . 15

Replacing the Warming Drawer . . . . . . . . . . 15

Testing Operation . . . . . . . . . . . . . . . . . . . 17

Service . . . . . . . . . . . . . . . . . . . . . . . 17

Before Calling Service . . .

. . . . . . . . . . . . . . 17

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

English 1

Safety Definitions

NOTICE: This indicates that damage to the appliance or

property may occur as a result of non-compliance with this

advisory.

Note: This alerts you to important information and/or tips.

Safety

PLEASE READ ALL INSTRUCTIONS BEFORE USING

THIS APPLIANCE.

Appliance Handling Safety

Do not lift appliance by the oven door handle. Remove the

oven door for easier handling and installation. See the

section “Removing the Oven Door” in the range Use and

Care manual.

Disposing of Packaging Materials

Remove all tape and packaging before using the range.

Properly dispose of the carton and plastic bags after

unpacking the range. Never allow children to play with

packaging materials.

9 WARNING

This indicates that death or serious injuries may

occur as a result of non-observance of this warning.

9 CAUTION

This indicates that minor or moderate injuries may

occur as a result of non-observance of this warning.

9 WARNING

If the information in this manual is not followed

exactly, fire or shock may result causing property

damage or personal injury.

9 WARNING

Do not repair or replace any part of the appliance

unless spe

cifically recommended in the manuals.

Improper installation, service or maintenance can

cause injury or property damage. Refer to this

manual for guidance. All other servicing should

be done by an authorized servicer.

• Ask your dealer to recommend a qualified

technician and an authorized repair service.

• Install only per the installation instructions

provided in the literature package

accompanying this range.

• Never modify or alter the construction of the

range including by removing leveling legs,

panels, wire covers, anti-tip brackets or

screws, or any other part of the appliance.

9 WARNING

TIP OVER HAZARD!

A child or adult can tip the

range over and be killed.

Verify that the anti-tip

bracket is securely installed.

Ensure the anti-tip bracket

is engaged whenever the

range is moved to a new

location.

Do not operate the range without the anti-tip bracket

in place. Failure to follow the instructions in this

manual can result in death or serious burns to

children and adults.

Check for proper installation and use of the anti-tip

bracket. Carefully tip the range forward pulling from

the back to ensure that the anti-tip bracket engages

the range leg and prevents tip-over. Range should

not move more than 1” (2.5 cm).

9 CAUTION

• Unit is heavy and requires at least two persons

or proper equipment to move.

• Hidden surfaces may have sharp edges. Use

caution when reaching behind or under

appliance.

• Do not use the oven or warming drawer (if

equipped) for storage.

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

English 2

Safety Codes and Standards

This appliance complies with one or more of the following

Standards:

• UL 858, Household Electric Ranges

• CAN/CSA-C22.2 No. 61 Household Cooking Ranges

It is the responsibility of the owner and the installer to

determine if additional requirements and/or standards

apply to specific installations.

Installation Location

To eliminate the risk of burns or fire by reaching over

heated surface units, cabinet storage space located above

the surface units should be avoided. If cabinet storage is to

be provided, the risk can be reduced by installing a hood

that projects horizontally a minimum of 5" (12.7 cm) beyond

the bottom of the cabinet.

Verify that cabinets above the range are a maximum of 13"

(330 mm) deep.

Child Safety

Do not store items of interest to children in the cabinets

above the range or on the backguard of a range. Children

climbing on the range to reach items could be seriously

injured.

Electric Safety

Before you plug in an electrical cord, be sure all controls

are in the OFF position.

Be sure your appliance is properly installed and grounded

by a qualified technician in accordance with the National

Electrical Code ANSI/NFPA 70 latest edition and local

electrical code requirements.

Local codes vary. Installation, electrical connections and

grounding must comply with all applicable codes.

For appliances equipped with a cord and plug, do not cut or

remove the ground prong. It must be plugged into a

matching grounding type receptacle to avoid electrical

shock. If there is any doubt as to whether the wall

receptacle is properly grounded, the customer should have

it checked by a qualified electrician.

If required by the National Electrical Code (or Canadian

Electrical Code), this appliance must be installed on a

separate branch circuit.

Only a power supply cord kit rated for this appliance and

marked “for use with ranges” shall be used.

Installer - show the owner the location of the circuit

breaker or fuse. Mark it for easy reference.

Important - Save these instructions for the local electrical

inspector's use.

Before installing, turn power OFF at the service panel. Lock

service panel to prevent power from being turned ON

accidentally.

Refer to rating label for more information.

See "Rating Label" under "Service" for rating label

location.

.

Proposition 65 Warning:

This product may contain a chemical known to the State

of California, which can cause cancer or reproductive

harm. Therefore, the packaging of your product may bear

the following label as required by California:

STATE OF CALIFORNIA PROPOSITION 65 WARNING:



WARNING

&DQFHUDQG5HSURGXFWLYH+DUPwww.P65Warnings.ca.gov

English 3

Preparation

Before You Begin

Tools and Parts Needed

• 40 or 50 Amp power supply cord kit with strain relief

(depending on local code).

Note: Not necessary for Canadian installations, cord is

preinstalled at factory.

• Measuring Tape

• Phillips Head Screwdriver

•1¼" Wrench

• Pencil

• T-20 Torx Screwdriver

• Screws (2) and Anchors (2) for Anti-Tip Bracket (Style

will vary depending on mounting surface)

• Level

• Drill and Drill Bit (3/16" masonry bit for concrete

screws)

• Soapy Water

• Safety Gloves and Goggles

• Cloth or Cardboard (Optional - to Protect Floor)

Parts Included

• Anti-Tip Bracket

• 2 wood screws

• 2 anchorless concrete screws

• Foam Tape (unless already installed on underside of

cooktop sides)

• Terminal lugs (for use with hard-wired installations)

Note: Terminal lugs are not necessary for Canadian

installations.

Additional Parts Needed for Hard-Wired

Installations

• Flexible conduit

• Torque wrench

Note: Power supply cord kit is not necessary for hard-wired

installations.

cabinet dimensions are correct for your unit and

that the r

equired electrical connections are

present.

___ 2. Refer to the installation manual for content

regarding Safety, Cabinet Dimensions, Removing

Packaging, Electrical Installation, Testing the

Installation and Customer Service.

Remove Packaging

1.

Cut the straps.

2.

3.

Open top of carton and remove top wood frame.

Lift the carton up and over the appliance to remove, or

carefully cut along the cut line on the back left side of

the carton with a blade shorter than 3/4” and remove

carton.

4.

Carefully remove internal protective packaging taking

care to secure any loose accessories and instruction

manuals.

5.

Remove bracket(s) securing appliance to base pad, if

present.

6.

The unit should stay on the packaging base until ready

to be lifted into cabinet cutout.

7.

Install the appliance according to the installation

instructions.

Packaging Bracket Removal-Left and

Right Sides

Note: Actual bracket varies in appearance. The bracket

remains in the packaging base. The un

it should stay on

the packaging base until ready to be lifted into cabinet

cutout or onto the lower oven.

Preparing Oven

Place oven in front of the cabinet where it is to be

installed

so that it is in line with the cabinet cutout.

Check to be sure all packing materials have been

removed from the unit. Also remove the accessories,

oven racks, literature pack and any shipping materials

from inside the oven cavity.

Installation Checklist

Please refer to the pages following for complete

installation instructions. Use this checklist to verify that

you have completed each step of the installation process.

This can help you avoid mistakes.

___ 1. Before installing the range, be sure to verify the

General Information

Overall Dimensions

Location Level and Plumb

For best results, cabinets, countertops, walls and floors in

the installation location should be as level and plumb as

possible. Variance may cause damage to countertops and

floors during installation, and may adversely affect cooking

and baking performance.

Installation Hints

To make the range lighter and easier to handle during

installation, remove the range oven door and warming

drawer (see “Removing the Oven Door” on page 13).

If the warming drawer is not removed, then tape must be

placed securely on the warming drawer before installation

to prevent it from opening while the range is being installed.

Place a piece of cardboard or cloth under the range during

installation to protect floors.

Electrical Requirements

Refer to rating label for more information. See the product

“Rating Label” in the section on Service in this manual.

We recommend that the range be installed with a

power cord set (not supplied with U.S. models). The

electrical rating of the power cord set must be 120/240 volt,

40 amperes minimum. The power cord set must be marked

“For Use with Ranges.” Always use a new power cord.

English 4

* Varies by location. Check local codes.

Electric Outlet Location

A flush mount 208/240 VAC dedicated circuit outlet is

required. Use the diagram below to make sure your

installation in properly prepared for the range. Note the

available space for the electrical outlet is shown in box (E)

in the illustration following.

Dimension Inches Centimeters

Height 36½” - 38” 92.7 cm - 96.6 cm

Width 31½” 80 cm

Depth 26¾” 68.1 cm

VOLTS

A/C

HZ RATING

KW

CIRCUIT

BREAKER

120/240 60 13.0 40 or 50 amps*

120/240 60 13.8 40 or 50 amps*

120/208 60 9.8 40 or 50 amps*

120/208 60 10.4 40 or 50 amps*

Verify that wiring to the house is adequate. Contact your

local utility company to verify that the present electric

service to your home is adequate. In some instances,

the size of the wiring to the house and service switch

must be increased to handle the electrical load

demanded by the range. Some wiring codes require a

separate circuit with separate disconnect switch and

fuses either in the main entrance panel or in a separate

switch and fuse box.

The range requires a minimum of a three-wire 120/240

or 120/208 volt, 40 - 50 amp, 60 Hz AC circuit. Check

local codes for proper amperage ratings. A four-wire

connection is preferred. Most local building regulations

and codes require that electrical wiring be done by

licensed electricians. Be sure to install your range

according to the electric codes in your region.

Electrical kW Rating

Ranges are dual rated for use on either 120/240 VAC or

120/208 VAC. Check the rating label for the kW rating.

Reference the kW rating in the table below to determine

amperage requirements.

___ 4. Move the range unit into place in front of the

installation opening, leaving the bottom packaging

on the unit to avoid damaging flooring.

___ 5. Plug the range into a properly configured

receptacle.

___ 6. Protect the flooring from damage, then lift the

range off of the bottom packaging and slide the

range all the way into place, making sure to route

the power cord correctly.

___ 7. Reinstall the oven door and warming drawer

removed in step 3 above.

___ 8. Consult the complete installation instructions and

follow the remainder of the procedures listed,

including performing an operation test.

___ 3. Removing the oven door and warming drawer prior

to installation reduces the unit weight and makes

the range easier to move. Additionally, the removal

of the oven door provides access to handhold for

lifting.

English 5

Cabinet Requirements

This unit is designed for installation near adjacent walls and

projecting surfaces constructed of combustible materials.

Prepare the countertop and cabinets.

Allow a minimum of 30" (76.2 cm) between cabinets

where range is to be installed. No side clearance is

required. Height is set by adjusting the range legs (see

later section, “Complete the installation” on

page 11).

Note: The slide-in range can also replace a

freestanding range. In this case, verify that the opening is

at least 30" (76.2 cm).

Install Ventilation

Bosch strongly recommends the installation of a ventilation

hood above this range. For most kitchens, a certified hood

rating of not less than 300 CFM is recommended. The

range hood must be installed according to instructions

furnished with the hood.

Required Clearance

These instructions were determined using standard

American cabinets. Standard base cabinets measure 36"

(91.4 cm) high x 25" (63.5 cm) deep. Cabinets over the

cooking surface and cabinets adjacent to those over the

cooking surface measure 13" (33 cm) deep from backwall.

If nonstandard cabinets are used, care should be taken to

alter dimensions accordingly.

From cooktop to materials above:

• There must be a minimum clearance of 30” (762 mm)

between the top of the cooking surface and the bottom

of an unprotected wood or metal cabinet.

• Bosch recommends the minimum clearances shown in

the installation diagrams contained in this manual.

Clearances from non-combustible materials are not

certified by CSA. Clearances less than shown in the

installation diagrams must be approved by local codes

and/or by the local authority having jurisdiction.

From the cooking surface to side materials:

No clearance is required from unit walls to adjacent vertical

combustible walls on rear, right or left.

9 WARNING

To eliminate the risk of burns or fire by reaching over

heated surface units, cabinet storage space located

above the surface units should be avoided. If

cabinet storage is to be provided, the risk can be

reduced by installing a hood that projects

horizontally a minimum of 5" (12.7 cm) beyond the

bottom of the cabinet.

English 6

Note: Some cabinet finishes cannot survive the

temperatures allowed by safety standards, particularly self-

cleaning ovens; the cabinets may discolor or stain. This is

most noticeable with laminate cabinets.

Flame retardant materials bear the mark:

UNDERWRITERS LABORATORIES INC. CLASSIFIED

MINERAL AND FIBER BOARDS SURFACE BURNING

CHARACTERISTICS, followed by the flame spread and

smoke ratings. These designations are shown as “FHC

(Flame Spread/Smoke Developed)“. Materials with “O”

flame spread ratings are flame-retardant. Local codes may

allow other flame spread ratings. It is the responsibility of

the installer to ensure installation is in accordance with

these ratings.

Prepare Walls and Floor

Seal any holes in the walls or floor. Remove any ob-

structions (extra electrical or gas connections, etc.) so that

range will rest against wall properly.

Countertop Requirements

Countertops must be smooth and level.

English 7

Installation Procedure

Installation of the Anti-Tip

Bracket

The range can tip forward, potentially causing injury and

damage, if the anti-tip bracket is not properly installed. Do

not operate the range without the anti-tip bracket in place.

Steps to Install the Anti-Tip Bracket

1. Adjust height of range to match countertop height and

level it by rotating the adjustable leg supports on the

bottom of the range, using a 1¼" wrench.

2. Position the bracket as shown below in the back left

corner of the installation opening, against the back wall

and the left cabinet wall. Mount the bracket using two

screws into either the floor or the base of the adjacent

cabinet. Note: The mounting surface must be secure.

When mounting to the cabinet wall make sure the

screws engage the frame of the cabinet, not the thin

wall of the cabinet only. Do not use a block or spacer to

fill a gap between the anti-tip bracket and the cabinet

wall.

3. Secure the bracket with two screws to the floor or to

the base of the cabinet wall. Depending on the floor or

cabinet material, use wood or anchorless concrete

screws (included). Concrete screws require the use of

a 3/16" masonry bit. Screws should provide firm

attachment into solid wood or flooring. Do not attempt

to anchor into drywall.

Electrical Connection

The range may be connected using an electric range cord

(as specified in the Electrical Requirements section

preceeding) or using a flexible conduit electrical

connection.

Note: In Canada, the range is shipped from the factory with

the range cord already installed. Continue to “Complete the

installation” on page 11.

Note: It is recommended that only qualified persons add a

power cord or make electrical connections to this

appliance.

For installations other than those in Canada, connect the

range cord at the terminal block. Access the terminal block

by removing the cover in the lower left hand corner of the

range back panel.

9 WARNING

A child or adult can tip the range

over and be killed.Verify that the

anti-tip bracket is securely

installed. Ensure the anti-tip

bracket is engaged when the

range is moved.

9 WARNING

Do not use an extension cord. If the power supply

cord is too short, have a qualified electrician install

an outlet near the appliance.

English 8

Install Strain Relief

Place strain relief in knockout below terminal block.

1. In the knockout panel below the terminal block, remove

the knockout that fits the strain relief that comes with

your range cord.

2. Feed the range cord through the hole and the strain

relief up to terminal block. Allow for slack in the cord

between the strain relief and terminal block.

3. Once the cord length/slack has been adjusted, attach

the strain relief per instructions included with strain

relief.

Tip: The knockout panel (below the terminal block) can be

removed from the range to install the strain relief. Remove

the panel from range, install strain relief in panel and

reattach. DO NOT remove entire range back panel.

Preparation for Power Connection

For installations where grounding through the neutral

conductor is prohibited: (a) disconnect the link from the

neutral, (b) use grounding terminal or lead to ground unit,

(c) connect neutral terminal to lead branch circuit neutral in

the usual manner. When the appliance is to be connected

by means of a cord kit, use 4-conductor cord for this

purpose.

Use only cord kits rated 125/250 volts, 40 amperes

(minimum), and labeled “For Use with Ranges”. Strain relief

provided with the cord must be installed per instructions

included with the cord.

Four-wire Range Cord Connection

(Recommended Method)

1. Disconnect electrical power at breaker box. Remove

the terminal block cover to expose the terminal block.

2. Remove the top nut (has an attached locking washer)

from each post.

Note: DO NOT remove the second nut/washer on each

post; these must stay in place to anchor the internal

wiring attached to the terminal block.

3. Remove screw from the bottom end of the ground

strap.

9 WARNING

The strain relief provided with your range cord must

be properly installed. Strain reliefs vary. Carefully

read and follow the instructions included with your

strain relief.

9 WARNING

Risk of Electric Shock or Fire. Grounding through

the neutral conductor is prohibited for new branch-

circuit installations (1996 NEC), mobile homes, and

recreational vehicles, or in an area where local

codes prohibit grounding through the neutral

conductor.

3-Wire Hookup 4-Wire Hookup

R= Red

W = White

GS = Grounding Strip

B = Black

R= Red

W = White

G = Green

B = Black

9 WARNING

To prevent electrical shock, the grounding prong on

the range cord should not be cut or removed under

any circumstances. It must be plugged into a

matching grounding type receptacle and connected

to a correctly polarized 240-Volt circuit. If there is

any doubt as to whether the wall receptacle is

properly grounded, have it checked by a qualified

electrician.

English 9

4. Remove the green grounding screw from the lower end

of the grounding strap. Remove the upper end of the

grounding strap from the center post of the junction

bar. Rotate the grounding strip (A) so that the wide end

is up and align the hole with the grounding hole below

the terminal block. Use the green grounding screw (B)

to attach the green wire (G) on top of grounding strap.

Tighten the grounding screw firmly, but do not

overtighten.

5. Attach the red wire to the left junction block terminal

using one of the nut/washers removed in step 2.

6. Attach the white wire to the center junction block

terminal using one of the nut/washer parts.

7. Attach the black wire to the right junction block terminal

using one of the nut/washer parts.

8. Tighten all connections securely and replace terminal

block cover.

9. Properly secure strain relief (see previous section).

Note: DO NOT plug in the range at this time.

Three-wire Range Cord Connection (Alternate Method)

The four-wire connection (above) is preferred, but where

local codes and ordinances permit grounding through the

neutral and where conversion to four-wire is impractical,

the unit may be connected to the power supply via a three-

wire connection.

1. Disconnect electrical power at breaker box.

2. Remove the terminal block cover to expose the

terminal block.

3. Remove the top nut (has an attached locking washer)

from each terminal post.

Note: DO NOT remove the second nut/washer on each

post. These must stay in place to anchor the internal

wiring attached to the terminal block.

4. Attach the white wire to the center junction block

terminal using one of the nut/washer parts.

5. Attach the red wire to the left junction block terminal

using one of the nut/washer parts removed in step 2.

6. Attach the black wire to the right junction block terminal

using one of the nut/washer parts.

7. Tighten all connections securely and replace terminal

block cover.

8. Properly secure strain relief (see previous section).

Note: DO NOT plug in range at this time.

English 10

Connect Flexible Conduit

The range can also be connected via flexible conduit. If

using this method, always use the lugs supplied.

Note: In Canada, the range is shipped from the factory with

the range cord already installed. Continue to “Complete the

installation”. For installations other than those in Canada,

connect the flexible conduit at the terminal block.

Terminal Lug/Wire Connection

In each instance where a wire is to be attached to a termi-

nal lug, perform the following steps:

1. Strip 3/8” (9.5 mm) of insulation from the end of the

wire.

2. Insert the stripped end of the wire into the terminal lug

(see A in the figure below) and then tighten each

clamping screw (see B in the figure below) with the

appropriate torque (see table).

Four-wire Flexible Conduit Connection

1. Disconnect electrical power at the breaker box.

2. Remove the terminal block cover to expose the

terminal block.

3. Remove the top nut (has an attached locking washer)

from each terminal post.

Note: DO NOT remove the second nut/washer on each

post. These must stay in place to anchor the internal wiring

attached to the terminal block.

4. Remove the green grounding screw from the lower end

of the grounding strap.

5. Remove the grounding strap from the center post on

the terminal block. The strap will not be needed with

the flexible conduit electric installation. Remove it from

the unit.

6. Attach the insulated grounding wire (G) to a terminal

lug (packaged with this manual) and secure the

terminal lug to the grounding hole with the green

grounding screw. Tighten the screw firmly, but do not

overtighten.

7. Attach the red wire (R) to a terminal lug and place the

terminal lug onto the left post. Replace the nut/washer

on the post and tighten to 20 in/lbs. (50.8 cm) of torque.

8. Attach the black wire (B) to a terminal lug and place the

terminal lug onto the right post. Replace the nut/washer

on the post and tighten to 20 in/lbs. (50.8 cm) of torque.

Wire Gauge Torque (in/lbs) Torque (Nm)

6353.95

8252.82

English 11

9. Properly secure the flexible conduit at knockout on

angle and at supply side junction box. The wiring is

now complete.

Note: DO NOT connect electrical power to the range at this

time.

Three-wire Flexible Conduit Connection

The four-wire connection is preferred, but where local

codes and ordinances permit grounding through neutral

and/or conversion to four-wire is impractical, the unit may

be connected to the power supply via a three-wire connec-

tion.

1. Disconnect electrical power at the breaker box.

2. Remove the terminal block cover to expose the

terminal block.

3. Remove the top nut, star washer, and round washer

from each post.

Note: DO NOT remove last round washer, last nut or inter-

nal wire leads.

4. Attach the red wire (R) to a terminal lug (packaged with

this manual) and place the terminal lug onto the left

post. Replace the nut/washer on the post and tighten to

20 in/lbs. (50.8 cm) of torque.

5. Attach the black wire (B) to a terminal lug and place the

terminal lug onto the right post. Replace the nut/washer

on the post and tighten to 20 in/lbs. (50.8 cm) of torque.

6. Attach the green wire (G) to a terminal lug and place

the terminal lug onto the center post. Replace the nut/

washer on the post and tighten to 20 in/lbs. (50.8 cm)

of torque.

7. Properly secure flexible conduit at knockout panel on

range and at supply side junction box. The wiring is

now complete.

Note: DO NOT connect electrical power to the range at this

time.

Complete the installation

Adjust Leveling Legs

1. Make sure that the circuit breaker is off and then plug

range cord into the electrical outlet.

2. Line up range in front of opening.

3. Measure (A) back left corner of opening from floor to

the top of the countertop.

English 12

4. Measure the back left corner of the range to the bottom

of cooktop (B). Adjust leveling legs until this height is

the same as the corner dimension.

5. Repeat in the back right corner.

6. Use a 1¼ “ wrench to adjust front leveling legs so that

the height from the bottom of the cooktop to the floor

matches the height of the corresponding countertop

surface.

Slide Range into Opening

1. Remove oven door using the procedure “Removing the

Oven Door” on page 13 and lift the range off of the

packaging base.

2. Plug in the power cord.

3. Dampen countertop and floor at bottom of opening with

soapy water.

Note: Clean up any remaining soapy water

immediately after sliding the range in place.

4. Slide the range into the opening, being careful not to

damage countertops, floors, or the range door or

warming drawer front. Do not apply pressure to

cooktop when sliding into position. Be careful not to

crimp the flexible electrical connector.

5. Install the oven door using the procedure “Replacing

the Oven Door” on page 14.

9 CAUTION

Unit is heavy and requires at least two persons or

proper equipment to move.

NOTICE

To avoid risk of damage to the range oven door, do

not lift, push, or pull the range by holding the door

handle. After the door has been removed, reach

inside the top of the oven cavity to locate a ridged

area near the front of the oven. Take care not to

touch the oven heating element also located at the

top of the oven cavity, just behind the ridged area.

9 CAUTION

It is recommended to wear gloves and long sleeves

to protect hands and forearms from abrasion and

potential scratches during the lifting process. It is

also recommended to take off watches and jewelry

and to wear work shoes during installation for foot

protection.

English 13

Check Back of Range for Proper Installation

1. The cooktop should rest lightly on the countertop.

2. There should not be any gap between the countertop

and the cooktop; however, the weight of the range

must not rest on the countertop. Look under the range

to verify that both back legs are resting solidly on the

floor. Also verify that the left range leg is retained by the

anti-tip bracket.

Removing the Oven Door

9 WARNING

When removing the door:

• Make sure oven is cool and power to the oven

has been turned off before removing the door.

Failure to do so could result in electrical shock

or burns.

• The oven door is heavy and parts of it are

fragile. Use both hands to remove the oven

door. The door front is glass. Handle carefully to

avoid breakage.

• Grasp only the sides of the oven door. Do not

grasp the handle as it may swing in your hand

and cause damage or injury.

• Failure to grasp the oven door firmly and

properly could result in personal injury or

product damage.

• To avoid injury from hinge bracket snapping

closed, be sure that both levers are securely in

place before removing the door. Also, do not

force door open or closed—the hinge could be

damaged and injury could result.

• Do not lay removed door on sharp or pointed

objects as this could break the glass. Lay on a

flat, smooth surface, positioned so that the door

cannot fall over.

To help avoid injury or

damage be sure to read

the above WARNING

before attempting to

remove the oven door.

1. Open the oven door to

its fully open,

horizontal position.

2. Flip levers on hinges

toward you.

Note: It may be necessary

to use a tool, such as a

screwdriver, to gently pry

the upper part of the lever

away from the housing.

Take care to avoid scratch-

ing the housing.

3. Bring both door hinge

levers to their fullest

down position as

shown in the

illustration. The left

and right door hinge

levers may differ

slightly but operate in

the same manner.

4. Close the oven door

until it catches on the

hinge stop levers,

locking the hinges at

the proper angle for

door removal. The

door will be open

about 7 inches at the

top. This takes the

spring tension off the

hinges so the door can

be easily lifted out.

5. The door is heavy.

Use both hands to

firmly grip it by the

sides. Do not grip the

door by the handle.

Maintaining the door

angle, lift the door

straight up

approximately ¾" to

unhook the hinges

from the slots and then

pull it out towards you

until the hinges are

clear of the oven

housing.

6. Place the door in a

convenient and stable

location for cleaning.

English 14

Replacing the Oven Door

1. Holding the door firmly

in both hands, grip it

on either side, not by

the handle.

2. Tilt the door back

slightly towards you

until it opens about 7"

at the top.

3. Slide the hinges into

the slots as far as they

will go and then lower

the door straight

down. The angle of

the door may need to

be adjusted slightly to

allow the hinges to

engage properly and

the door to lower into

place. The door

should lower about ¾"

and stop. If not, the

hinges have not

engaged properly and

the door could fall if it

is released.

4. Once both hinges are

fully engaged as

described in Step 3,

gently open the door

until it is fully open.

5. Push the levers on

both the hinges up

and forward until they

are locked into the

slot, flush with the

front of the oven body.

6. Close and open door

slowly to be sure it is

correctly and securely

in place.

Removing the Warming Drawer

9 CAUTION

To prevent burns, do not remove drawer while hot.

Be sure the drawer is empty before removing.

English 15

Removing Drawer from Housing

NOTICE: The following is the manufacturer’s

recommendations for removing and installing the drawer

to minimize the risk of damage to the PTO mechanism.

1.

Remove the drawer from the drawer housing.

▯ Pull drawer to fully open position.

▯ Press down right drawer release lever.

▯ Lift up left drawer release lever.

▯ Firmly pull the drawer straight out.

▯ Retract cabinet rails while drawer is removed.

2.

Grasp both sides of the drawer and pulling straight

and level, carefully remove the drawer housing. This

step may require light to moderate force to completely

remove drawer.

3.

Install or service (clean) housing with drawer removed.

-

0

8

)*()

@

.&%

13

00

'



0

/

0

''

Installing Drawer to Housing

The slides mounted to each side of the housing wall

have two moving components, an inner rail and a ball

bearing carrier which need to be in the proper orientation

for accurate installation and alignment.

There is also a visible locking mechanism located at the

rear of each slide.

%DOO%HDULQJ&DUULHU

Note: The housing of your warming drawer should

match the image below identically before starting your

installation. The ball bearing carrier should be locked in

to the inner rail’s black plastic rail tip at the front of the

inner rail.

6OLGH,QQHU5DLO

/RFNLQJ0HFKDQLVP

%DOO%HDULQJ&DUULHU

6OLGH,QQHU5DLO

English 16

1.

With the drawer removed, set the slide inner rail to the

drawer locked position by pushing the slide inner rail

toward the rear of the housing until it locks in place.

Note: A moderate force pushing on the black plastic

ball carrier locking mechanism is required to set the

slide to the drawer locked position. The drawer is

locked when it remains in place and does not spring

back to the open position.

2.

Position the drawer assembly in front of the housing

assembly and align the rail (plastic rail tip) to the slide

ball carrier assembly. Keeping the drawer assembly

level and square to the housing, gently insert the

drawer to the housing assembly.

Notes

▯ A slight side-to-side wiggle motion may be required

to properly get the ball bearings to accurately align.

▯ Remember: You are attempting to align two sets of

ball bearings at this point. If more than a moderate

force is required to insert the drawer at this time,

remove the drawer and repeat the installation

procedure to this point.

3.

Continue to insert the drawer keeping the drawer level

and square to the housing until a slight increase in

resistance is felt at the approximate position shown

below.

4MJEF*OOFS3BJM

-PDLJOH.FDIBOJTN

4MJEF*OOFS3BJMJTJOMPDLFEQPTJUJPO

NOTICES

▯ At this position, a slight increase in closure force is

required with several small increments of force

applied to the drawer to accurately align and set the

drawer for proper operation.

▯ An audible “click” should be heard when the drawer

is properly closed causing the drawer to lock in the

closed position.

La page est en cours de chargement...

Bosch Benchmark HEIP056U Guide d'installation

Ce manuel convient également à

Bosch Benchmark HEIP056U Guide d'installation

dans d''autres langues

Autres documents