Yamaha CLP555 Manuel utilisateur

Marque: Yamaha

Modèle: CLP555

Catégorie: Instruments de musique

Taper: Manuel utilisateur

Ce manuel convient également à

CLP-555

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in this

manual, meets FCC requirements. Modifications not expressly approved by

Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another

product use only high quality shielded cables. Cable/s supplied with this product

MUST be used. Follow all installation instructions. Failure to follow instructions

could void your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements

listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with

these requirements provides a reasonable level of assurance that your use of

this product in a residential environment will not result in harmful interference

with other electronic devices. This equipment generates/uses radio frequencies

and, if not installed and used according to the instructions found in the users

manual, may cause interference harmful to the operation of other electronic

devices. Compliance with FCC regulations does not guarantee that interference

will not occur in all installations. If this product is found to be the source of inter-

ference, which can be determined by turning the unit “OFF” and “ON”, please try

to eliminate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by the

interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits

or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the

antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type

cable.

If these corrective measures do not produce satisfactory results, please contact

the local retailer authorized to distribute this type of product. If you can not

locate the appropriate retailer, please contact Yamaha Corporation of America,

Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by Yamaha

Corporation of America or its subsidiaries.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.

• This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd.

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

IMPORTANT. The wires in this mains lead are coloured in accordance with the

following code:

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may not correspond

with the coloured makings identifying the terminals in your plug proceed as follows:

The wire which is coloured BLUE must be connected to the terminal which is

marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal which is

marked with the letter L or coloured RED.

Making sure that neither core is connected to the earth terminal of the three pin

plug.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG

TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA

LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE

LA PRISE ET POUSSER JUSQU’AU FOND.

• This applies only to products distributed by Yamaha Canada Music Ltd.

• Ceci ne s’applique qu’aux produits distribués par Yamaha Canada Musique Ltée.

ENGLISH

DEUTSCHFRANÇAISESPAÑOL

Owner’s Manual

Bedienungsanleitung

Mode d’emploi

Manual de instrucciones

IMPORTANT



Check Your Power Supply



Make sure that your local AC mains vol-

tage matches the voltage specified on

the name plate on the bottom panel. In

some areas a voltage selector may be

provided on the bottom panel of the

main keyboard unit near the power

cord. Make sure that the voltage selec-

tor is set for the voltage in your area.

The voltage selector is set at 240V

when the unit is initially shipped. To

change the setting use a “minus” screw-

driver to rotate the selector dial so that

the correct voltage appears next to the

pointer on the panel.



WICHTIG



Überprüfung der Stromversorgung



Vergewissern Sie sich vor dem Ansch-

ließen an das Stromnetz, daß die ör-

tliche Netzspannung den Betriebsspan-

nungswerten auf dem Typenschild an

der Unterseite des Instruments ents-

pricht. In bestimmten Verkaufsgebieten

ist das Instrument mit einem Span-

nungswähler an der Unterseite neben

der Netzkabeldurchführung ausgestat-

tet. Falls vorhanden, muß der Span-

nungswähler auf die örtliche Netzspan-

nung eingestellt werden. Der Span-

nungswähler wurde werkseitig auf 240

V voreingestellt. Zum Verstellen drehen

Sie den Spannungsregler mit einem

Schlitzschraubendreher, bis der Zeiger

auf den korrekten Spannungswert weist.



IMPORTANTE

Verifique la alimentación de corriente



Asegúrese de que tensión de alimenta-

ción de CA de su área corresponde con

la tensión especificada en la placa de

características del panel inferior de la

unidad del teclado principal, cerca del

cable de alimentación. Asegúrese de

que el selector de tensión esté ajustado

a la tensión de su área. El selector de

tensión se ajusta a 240V cuando la uni-

dad sale de fábrica. Para cambiar el

ajuste, emplee un destornillador de ca-

beza “recta” para girar el selector de

modo que aparezca la tensión correcta

al lado del indicador del panel.



IMPORTANT

Contrôler la source d’alimentation



Vérifiez que la tension spécifiée sur le

panneau arrière correspond à la tension

du secteur. Dans certaines régions, l’in-

strument peut être équipé d’un sélec-

teur de tension situé sur le panneau in-

férieur du clavier à proximité du cordon

d’alimentation. Vérifiez que ce sélec-

teur est bien réglé en fonction de la ten-

sion secteur de votre région. Le sélec-

teur de tension est réglé sur 240 V au

départ d’usine. Pour modifier ce ré-

glage, utilisez un tournevis à lame plate

pour tourner le sélecteur afin de mettre

l’indication correspondant à la tension

de votre région vis à vis du repère trian-

gulaire situé sur le panneau.



M.D.G., EMI Division © Yamaha Corporation 1997

VV62120 706POCP1.2-0310 Printed in Japan

Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Nie-

derlassung und bei Yamaha Vertragshändlern in den jeweiligen

Bestimmungsländern erhältlich.

Para detalles sobre productos, contacte su tienda Yamaha más cercana

o el distribuidor autorizado que se lista debajo.

For details of products, please contact your nearest Yamaha or the

authorized distributor listed below.

Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha

ou au distributeur le plus proche de vous figurant dans la liste suivante.

ITALY

Yamaha Musica Italia S.P.A.,

Home Keyboard Division

Viale Italia 88, 20020 Lainate (Milano), Italy

Tel: 02-935-771

SPAIN

Yamaha-Hazen Electronica Musical, S.A.

Jorge Juan 30, 28001, Madrid, Spain

Tel: 91-577-7270

PORTUGAL

Valentim de Carvalho CI SA

Estrada de Porto Salvo, Paço de Arcos 2780 Oeiras,

Portugal

Tel: 01-443-3398/4030/1823

GREECE

Philippe Nakas S.A.

Navarinou Street 13, P.Code 10680, Athens, Greece

Tel: 01-364-7111

SWEDEN

Yamaha Scandinavia AB

J. A. Wettergrens Gata 1

Box 30053

S-400 43 Göteborg, Sweden

Tel: 031 89 34 00

DENMARK

YS Copenhagen Liaison Office

Generatorvej 8B

DK-2730 Herlev, Denmark

Tel: 44 92 49 00

FINLAND

Warner Music Finland OY/Fazer Music

Aleksanterinkatu 11, P.O. Box 260

SF-00101 Helsinki, Finland

Tel: 0435 011

NORWAY

Narud Yamaha AS

Grini Næringspark 17

N-1345 Østerås, Norway

Tel: 67 14 47 90

ICELAND

Skifan HF

Skeifan 17 P.O. Box 8120

IS-128 Reykjavik, Iceland

Tel: 525 5000

OTHER EUROPEAN COUNTRIES

Yamaha Europa GmbH.

Siemensstraße 22-34, 25462 Rellingen, F.R. of

Germany

Tel: 04101-3030

ASIA

HONG KONG

Tom Lee Music Co., Ltd.

11/F., Silvercord Tower 1, 30 Canton Road,

Tsimshatsui, Kowloon, Hong Kong

Tel: 730-1098

INDONESIA

PT. Yamaha Music Indonesia (Distributor)

PT. Nusantik

Gedung Yamaha Music Center, Jalan Jend. Gatot

Subroto Kav. 4, Jakarta 12930, Indonesia

Tel: 21-520-2577

MALAYSIA

Yamaha Music Malaysia, Sdn., Bhd.

16-28, Jalan SS 2/72, Petaling Jaya, Selangor,

Malaysia

Tel: 3-717-8977

PHILIPPINES

Yupangco Music Corporation

339 Gil J. Puyat Avenue, P.O. Box 885 MCPO,

Makati, Metro Manila, Philippines

Tel: 819-7551

SINGAPORE

Yamaha Music Asia Pte., Ltd.

Blk 17A Toa Payoh #01-190 Lorong 7

Singapore 1231

Tel: 354-0133

TAIWAN

Kung Hsue She Trading Co., Ltd.

No. 322, Section 1, FuHsing S. Road,

Taipei 106, Taiwan. R.O.C.

Tel: 02-709-1266

THAILAND

Siam Music Yamaha Co., Ltd.

865 Phornprapha Building, Rama I Road,

Patumwan, Bangkok 10330, Thailand

Tel: 2-215-3443

THE PEOPLE’S REPUBLIC OF CHINA

AND OTHER ASIAN COUNTRIES

Yamaha Corporation,

International Marketing Division

Nakazawa-cho 10-1, Hamamatsu, Japan 430

Tel: 053-460-2317

NORTH AMERICA

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Scarborough, Ontario,

M1S 3R1, Canada

Tel: 416-298-1311

U.S.A.

Yamaha Corporation of America,

Keyboard Division

6600 Orangethorpe Ave., Buena Park, Calif. 90620,

U.S.A.

Tel: 714-522-9011

MIDDLE & SOUTH AMERICA

MEXICO

Yamaha De Mexico S.A. De C.V.,

Departamento de ventas

Javier Rojo Gomez No.1149, Col. Gpe Del

Moral, Deleg. Iztapalapa, 09300 Mexico, D.F.

Tel: 686-00-33

BRASIL

Yamaha Musical Do Brasil LTDA.

Ave. Reboucas 2636, São Paulo, Brasil

Tel: 011-853-1377

PANAMA

Yamaha De Panama S.A.

Edificio Interseco, Calle Elvira Mendez no.10,

Piso 3, Oficina #105, Ciudad de Panama, Panama

Tel: 507-69-5311

OTHER LATIN AMERICAN COUNTRIES

AND CARIBBEAN COUNTRIES

Yamaha Music Latin America Corp.

6101 Blue Lagoon Drive, Miami, Florida 33126,

U.S.A.

Tel: 305-261-4111

MIDDLE EAST

TURKEY/CYPRUS

Yamaha Europa GmbH.

Siemensstraße 22-34, 25462 Rellingen,

F.R. of Germany

Tel: 04101-3030

OTHER COUNTRIES

Yamaha Corporation,

International Marketing Division

Nakazawa-cho 10-1, Hamamatsu, Japan 430

Tel: 053-460-2312

EUROPE

THE UNITED KINGDOM

Yamaha-Kemble Music (U.K.) Ltd.

Sherbourne Drive, Tilbrook, Milton Keynes,

MK7 8BL, England

Tel: 01908-366700

IRELAND

Danfay Ltd.

61D, Sallynoggin Road, Dun Laoghaire, Co. Dublin

Tel: 01-2859177

GERMANY/SWITZERLAND

Yamaha Europa GmbH.

Siemensstraße 22-34, 25462 Rellingen,

F.R. of Germany

Tel: 04101-3030

AUSTRIA

Yamaha Music Austria

Schleiergasse 20, A-1100 Wien Austria

Tel: 0222-60203900

THE NETHERLANDS

Yamaha Music Nederland

Kanaalweg 18G, 3526KL, Utrecht, The Netherlands

Tel: 030-2828411

BELGIUM

Yamaha Music Belgium

Keiberg Imperiastraat 8, 1930 Zaventem, Belgium

Tel: 02-7258220

FRANCE

Yamaha Musique France,

Division Claviers

BP 70-77312 Marne-la-Valée Cedex 2, France

Tel: 01-64-61-4000

HEAD OFFICE Yamaha Corporation, Electronic Musical Instrument Division

Nakazawa-cho 10-1, Hamamatsu, Japan 430

Tel: 053-460-3255

AFRICA

Yamaha Corporation,

International Marketing Division

Nakazawa-cho 10-1, Hamamatsu, Japan 430

Tel: 053-460-2312

OCEANIA

AUSTRALIA

Yamaha Music Australia Pty. Ltd.

17-33 Market Street, South Melbourne, Vic. 3205,

Australia

Tel: 3-699-2388

NEW ZEALAND

Music Houses of N.Z. Ltd.

146/148 Captain Springs Road, Te Papapa,

Auckland, New Zealand

Tel: 9-634-0099

COUNTRIES AND TRUST

TERRITORIES IN PACIFIC OCEAN

Yamaha Corporation,

International Marketing Division

Nakazawa-cho 10-1, Hamamatsu, Japan 430

Tel: 053-460-2317

[CL] 9

92-469 1

ENVIRONMENTAL ISSUES: Yamaha strives to pro-

duce products that are both user safe and environmentally

friendly. We sincerely believe that our products and the

production methods used to produce them, meet these

goals. In keeping with both the letter and the spirit of the

law, we want you to be aware of the following:

Battery Notice: This product MAY contain a small non-

rechargable battery which (if applicable) is soldered in

place. The average life span of this type of battery is ap-

proximately five years. When replacement becomes nec-

essary, contact a qualified service representative to per-

form the replacement.

Warning: Do not attempt to recharge, disassemble, or

incinerate this type of battery. Keep all batteries away

from children. Dispose of used batteries promptly and as

regulated by applicable laws. Note: In some areas, the

servicer is required by law to return the defective parts.

However, you do have the option of having the servicer

dispose of these parts for you.

Disposal Notice: Should this product become damaged

beyond repair, or for some reason its useful life is consid-

ered to be at an end, please observe all local, state, and

federal regulations that relate to the disposal of products

that contain lead, batteries, plastics, etc.

NOTICE: Service charges incurred due to lack of knowl-

edge relating to how a function or effect works (when the

unit is operating as designed) are not covered by the

manufacturer’s warranty, and are therefore the owners

responsibility. Please study this manual carefully and con-

sult your dealer before requesting service.

NAME PLATE LOCATION: The graphic below indi-

cates the location of the name plate. The model number,

serial number, power requirements, etc., are located on

this plate. You should record the model number, serial

number, and the date of purchase in the spaces provided

below and retain this manual as a permanent record of

your purchase.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

PRODUCT SAFETY MARKINGS: Yamaha electronic

products may have either labels similar to the graphics

shown below or molded/stamped facsimiles of these

graphics on the enclosure. The explanation of these graph-

ics appears on this page. Please observe all cautions indi-

cated on this page and those indicated in the safety in-

struction section.

See bottom of Keyboard enclosure for graphic symbol markings

The exclamation point within the equi-

lateral triangle is intended to alert the

user to the presence of important oper-

ating and maintenance (servicing) in-

structions in the literature accompany-

ing the product.

The lightning flash with arrowhead

symbol, within the equilateral triangle,

is intended to alert the user to the pres-

ence of uninsulated “dangerous volt-

age” within the product’s enclosure that

may be of sufficient magnitude to con-

stitute a risk of electrical shock.

IMPORTANT NOTICE: All Yamaha electronic prod-

ucts are tested and approved by an independent safety

testing laboratory in order that you may be sure that when

it is properly installed and used in its normal and custom-

ary manner, all foreseeable risks have been eliminated.

DO NOT modify this unit or commission others to do so

unless specifically authorized by Yamaha. Product per-

formance and/or safety standards may be diminished.

Claims filed under the expressed warranty may be denied

if the unit is/has been modified. Implied warranties may

also be affected.

SPECIFICATIONS SUBJECT TO CHANGE: The

information contained in this manual is believed to be

correct at the time of printing. However, Yamaha reserves

the right to change or modify any of the specifications

without notice or obligation to update existing units.

SPECIAL MESSAGE SECTION

Model _____________________________________

Serial No. __________________________________

Purchase Date ______________________________

• Take care that the key cover does not pinch your fingers, and do not

insert a finger or hand in the key cover gap.

• Never insert or drop paper or metallic or other objects between the slits of

the key cover and the keyboard. If this happens, immediately turn off the

power and remove the electric plug from the outlet and have the instru-

ment inspected by qualified Yamaha service personnel.

• Do not place the instrument against a wall (allow at least 3 cm/one-inch

from the wall), since this can cause inadequate air circulation, and possi-

bly result in the instrument overheating.

• Read carefully the attached documentation explaining the assembly pro-

cess. Failure to assemble the instrument in the proper sequence might

result in damage to the instrument or even injury.

• Do not operate the instrument for a long period of time at a high or un-

comfortable volume level, since this can cause permanent hearing loss. If

you experience any hearing loss or ringing in the ears, consult a physi-

cian.

■USING THE BENCH (if included)

• Do not play carelessly with or stand on the bench. Using it as a tool or

step-ladder or for any other purpose might result in accident or injury.

• Only one person should sit on the bench at a time, in order to prevent the

possibility of accident or injury.

• Do not attempt to adjust the bench height while sitting on the bench,

since this can cause excessive force to be imposed on the adjustment

mechanism, possibly resulting in damage to the mechanism or even in-

jury.

• If the bench screws become loose due to extensive long-term use, tighten

them periodically using the included tool.

■SAVING USER DATA

• Save all data to an external device such as the Yamaha DOU-10 Disk

Orchestra Unit in order to help prevent the loss of important data due to a

malfunction or user operating error.

Yamaha cannot be held responsible for damage caused by improper use or modi-

fications to the instrument, or data that is lost or destroyed.

Always turn the power off when the instrument is not in use.

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep these precautions in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock,

short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:

• Do not open the instrument or attempt to disassemble the internal parts

or modify them in any way. The instrument contains no user-serviceable

parts. If it should appear to be malfunctioning, discontinue use immedi-

ately and have it inspected by qualified Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in damp or wet

conditions, or place containers on it containing liquids which might spill

into any openings.

• If the power cord or plug becomes frayed or damaged, or if there is a

sudden loss of sound during use of the instrument, or if any unusual smells

or smoke should appear to be caused by it, immediately turn off the power

switch, disconnect the electric plug from the outlet, and have the instru-

ment inspected by qualified Yamaha service personnel.

• Only use the voltage specified as correct for the instrument. The required

voltage is printed on the name plate of the instrument.

• Before cleaning the instrument, always remove the electric plug from the

outlet. Never insert or remove an electric plug with wet hands.

• Check the electric plug periodically and remove any dirt or dust which

may have accumulated on it.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the

instrument or other property. These precautions include, but are not limited to, the following:

• Do not place the power cord near heat sources such as heaters or radia-

tors, and do not excessively bend or otherwise damage the cord, place

heavy objects on it, or place it in a position where anyone could walk on,

trip over, or roll anything over it.

• When removing the electric plug from an outlet, always hold the plug

itself and not the cord. Pulling by the cord can damage it.

• Do not connect the instrument to an electrical outlet using a multiple-

connector. Doing so can result in lower sound quality, or possibly cause

overheating in the outlet.

• Remove the electric plug from the outlet when the instrument is not to be

used for extended periods of time, or during electrical storms.

• Before connecting the instrument to other electronic components, turn off

the power for all components. Before turning the power on or off for all

components, set all volume levels to minimum.

• Do not expose the instrument to excessive dust or vibrations, or extreme

cold or heat (such as in direct sunlight, near a heater, or in a car during the

day) to prevent the possibility of panel disfiguration or damage to the

internal components.

• Do not use the instrument near other electrical products such as televi-

sions, radios, or speakers, since this might cause interference which can

affect proper operation of the other products.

• Do not place the instrument in an unstable position where it might acci-

dentally fall over.

• Before moving the instrument, remove all connected cables.

• When cleaning the instrument, use a soft, dry cloth. Do not use paint

thinners, solvents, cleaning fluids, or chemical-impregnated wiping cloths.

Also, do not place vinyl or plastic objects on the instrument, since this

might discolor the panel or keyboard.

• Gently remove dust and dirt with a soft cloth. Do not wipe too hard since

small particles of dirt can scratch the instrument’s finish.

• Bumping the surface of the instrument with metal, porcelain, or other hard

objects can cause the finish to crack or peel. Use caution.

• Do not rest your weight on, or place heavy objects on the instrument, and

do not use excessive force on the buttons, switches or connectors.

The Control Panel ...................................................4

Preparation ..............................................................6

■

The Music Stand.............................................6

■

The Key Cover ................................................6

■

Opening and Closing the Lid........................6

Connections .............................................................. 7

Selecting & Playing Voices....................................8

Playing the Demonstration Tunes........................9

■

Piano Song A-B Repeat...............................10

■

Piano Song Part Cancel ..............................11

●

Synchro Start ..........................................11

●

Left Pedal Start/Stop ...............................11

The Dual Mode ......................................................12

●

Other Dual Mode Functions ....................12

The Split Mode ......................................................13

●

Selecting the Left-hand Voice.................. 13

●

Setting the Split Point .............................. 13

●

Other Split Mode Functions.....................13

Reverb .................................................................... 14

●

Adjusting Reverb Depth .......................... 14

The Chorus Effect ..................................................15

●

Adjusting Effect Depth.............................15

The Pedals..............................................................15

●

Soft (Left) Pedal ...................................... 15

●

Sostenuto (Center) Pedal........................ 15

●

Damper (Right) Pedal..............................15

Touch Sensitivity ...................................................16

Transposition .........................................................16

Introduction

Thank you for choosing a Yamaha CLP-555

Clavinova. Your Clavinova is a fine musical

instrument that employs advanced Yamaha music

technology. With the proper care, your Clavinova

will give you many years of musical pleasure.

● Yamaha’s AWM (Advanced Wave Memory) tone

generator system offers rich, realistic voices. Both

models feature stereo sampling of the piano voices

for unmatched realism and expressive power.

● Piano-like touch response — adjustable in 4 stages

— provides extensive expressive control and

outstanding playability.

● Dual mode allows 2 voices to be played simulta-

neously.

● Split mode allows different voices to be played by

the left and right hands.

● Unique Clavinova Tone voice provides a fresh

sound for new musical expression.

● Metronome feature with variable tempo facilitates

practice.

● Digital recorder lets you record and play back

anything you play on the keyboard (up to approxi-

mately 4,200 notes).

● MIDI compatibility and a range of MIDI functions

make the Clavinova useful in a range of advanced

MIDI music systems.

● Built-in computer interface for direct connection to

personal computers running advanced music

software.

In order to make the most of your Clavinova’s

performance potential and features, we urge you

to read this Owner’s Manual thoroughly, and keep

it in a safe place for later reference.

■

F5: Metronome Functions ...........................27

F5.1: Beat ..................................................27

F5.2: Volume ..............................................27

■

F6: Left Pedal Mode .....................................27

■

F7: Piano Song Part Cancel Volume........... 27

■

F8: MIDI Functions....................................... 28

●

A Brief Introduction to MIDI ..................... 28

F8.1: MIDI Transmit Channel Selection...... 28

F8.2: MIDI Receive Channel Selection ......28

F8.3: Local Control ON/OFF ......................29

F8.4: Program Change ON/OFF................ 29

F8.5: Control Change ON/OFF ..................30

F8.6: MIDI Transmit Transpose................... 30

F8.7: Panel/Status Transmit ....................... 30

F8.8: Bulk Data Dump................................30

■

F9: Backup Functions .................................31

F9.1: Voice ................................................. 31

F9.2: MIDI .................................................. 31

F9.3: Tuning ...............................................31

F9.4: Pedal................................................. 31

Connecting to a Personal Computer .................. 32

●

Connecting to an Apple Macintosh Series

Computer.................................................32

●

Connecting to an IBM-PC/AT Series

Computer.................................................33

●

Connecting to an NEC PC-9801/9821

Series Computer .....................................33

Troubleshooting .....................................................34

Factory Preset Recall............................................. 34

Options & Expander Modules ............................... 34

MIDI Data Format.................................................... 35

MIDI Implementation Chart ...................................39

Keyboard Stand Assembly....................................40

Demo Song List......................................................48

Default Setting List ................................................ 48

Specifications.........................................................49

Tuning......................................................................17

●

Tuning Up ................................................17

●

Tuning Down............................................17

●

To Restore Standard Pitch ...................... 17

The Metronome & Tempo Control ...................... 18

■

The Metronome ............................................18

●

Metronome Volume ................................. 18

●

Other Metronome Functions ................... 18

■

Tempo Control.............................................. 18

Using the Recorder ...............................................19

■

Recording .....................................................19

●

Changing the Initial Settings ................... 20

●

Erasing a Single Track............................. 20

■

Playback .......................................................21

●

Synchro Start .......................................... 21

●

Left Pedal Start/Stop ...............................21

The Function Mode ............................................... 22

●

To Select a Function … ...........................22

■

F1: Tuning ..................................................... 23

■

F2: Scale ....................................................... 23

■

F3: Dual Mode Functions ............................ 24

F3.1: Dual Balance ....................................24

F3.2: Dual Detune......................................24

F3.3: 1st Voice Octave Shift .......................24

F3.4: 2nd Voice Octave Shift ...................... 24

F3.5: 1st Voice Effect Depth.......................25

F3.6: 2nd Voice Effect Depth......................25

F3.7: Slow-attack Strings ...........................25

F3.8: Reset ................................................25

■

F4: Split Mode Functions ............................ 25

F4.1: Split Point.......................................... 25

F4.2: Split Balance..................................... 26

F4.3: Right Voice Octave Shift ...................26

F4.4: Left Voice Octave Shift ...................... 26

F4.5: Right Voice Effect Depth ................... 26

F4.6: Left Voice Effect Depth...................... 26

F4.7: Damper Mode ................................... 26

F4.8: Reset ................................................26

Contents

1 [POWER] Switch

Press the [POWER] switch once to turn the power

ON, a second time to turn the power OFF. When the

power is initially turned ON, a voice selector LED

will light, and the power indicator located below the

left end of the keyboard will light.

2 [MASTER VOLUME] Control

The [MASTER VOLUME] control adjusts the

volume (level) of sound produced by the Clavinova’s

internal stereo sound system. The [MASTER VOL-

UME] control also adjusts headphone volume when a

pair of headphones is plugged into the PHONES jack

(page 7).

The Control Panel

3 [FUNCTION] Button

This button accesses a range of utility functions

— including the MIDI functions — that significantly

enhance versatility and playability. See page 22 for

details.

4 [TRANSPOSE] Button

The [TRANSPOSE] button allows access to the

Clavinova’s TRANSPOSE function (to shift the pitch

of the entire keyboard up or down in semitone

intervals).

5 [SPLIT] Button

Engages the split mode, in which different voices

can be played on the left- and right-hand sections of

the keyboard. See page 13 for details.

–

CLP-

555

STEREO SAMPLING

POWER

B0A0G0F0E0D0C0B-1A-1

C1 D1 E1 F1 G1 A1 B1 C2 D2 E2 F2 G2 A2 B2 C3 D3 E3 F3 G3 A3 B3 C4 D4 E4 F4 G4 A4 B4 C5 D5 E5 F5 G5 A5 B5 C6

278456

9@0 !

MASTER VOLUME

FUNCTION

TRANSPOSE SPLIT

VARIATION

PIANO 1

PIANO 2 CLAVI.TONE E.PIANO 1 E.PIANO 2 STRINGS

HARPSI-

CHORD

PIPE

ORGAN 1

PIPE

ORGAN 2

REVERB

ROOM

HALL 1

HALL 2

STAGE

HARD

MEDIUM

SOFT

FIXED

EFFECT TOUCH

MAX

MIN

METRONOME

TEMPO/

SONG

–

N O

Y ES

DEMO



PIANO SONG

PHONES Jacks

(Bottom Panel)

Tuning keys

(See page 17)

MASTER VOLUME

FUNCTION

TRANSPOSE SPLIT

VARIATION

PIANO 1

PIANO 2 CLAVI.TONE E.PIANO 1 E.PIANO 2 STRINGS

HARPSI-

CHORD

PIPE

ORGAN 1

PIPE

ORGAN 2

REVERB

ROOM

HALL 1

HALL 2

STAGE

HARD

MEDIUM

SOFT

FIXED

EFFECT TOUCH

MAX

MIN

METRONOME

TEMPO/

SONG

YES

START



STOP

REC

DEMO



PIANO SONG

RECORDER

The Control Panel

6 [REVERB] Button

The [REVERB] button selects a number of digital

reverb effects that you can use for extra depth and

expressive power. See page 14 for details.

7 [EFFECT] Button

This button engages a chorus effect which can

give your sound greater depth and animation.

8 [TOUCH] Button

The [TOUCH] button makes it easy to adjust the

touch response of the Clavinova to match your

playing style. See page 16 for details.

9 Voice Selectors & [VARIATION] Button

The CLP-555 has nine voice selectors and a

[VARIATION] button. Simply press any of the voice

selectors to select the corresponding voice. The voice

selector LED will light to indicate which voice is

currently selected. Press the [VARIATION] button

so that its indicator lights to select a variation of the

currently selected voice.

There is also a dual mode in which two voices can

be played simultaneously across the full range of the

keyboard (see page 12 for details), and a split mode

which allows different voices to be played by the left

and right hands (see page 13 for details).

0 [METRONOME] Button

Turns the metronome sound on and off. The

[TEMPO/SONG] buttons, below, are used to set the

tempo of the metronome sound, and the volume of

the metronome sound if used while the [METRO-

NOME] button is held — page 18.

! [TEMPO/SONG] (–/NO, +/YES) Buttons

These buttons adjust the tempo of the metronome

function as well as the playback tempo of the re-

corder function. The tempo range is from 32 to 280

beats per minute — page 18. These same buttons are

also used to select a piano song number for playback

— page 9. The [TEMPO/SONG] buttons are also

used to adjust a range of other parameters (i.e. their

“–/NO” and “+/YES” functions).

@ [DEMO/PIANO SONG] Button

Activates the demo playback mode in which you

can select playback of different demonstration

sequences for each of the Clavinova’s voices, and a

range of 30 piano songs. See page 9 for details.

# RECORDER [START/STOP] and [REC] But-

tons

These buttons control the Clavinova’s recorder,

letting you record and play back just about anything

you play on the keyboard — up to a maximum of

about 4,200 notes. See page 19 for details.

$ RECORDER [1] and [2] Buttons

The CLP-555 has a 2-track recorder, and these

buttons are used to select the track(s) to be recorded

or played back. See page 19 for details.

% Pedals

The soft (left), sostenuto (center) and damper

(right) pedals provide a range of expressive control

capabilities similar to the pedal functions on an

acoustic piano. See page 15 for details.

Soft pedal

Damper pedal

Sostenuto pedal

D6 E6 F6 G6 A6 B6 C7

$ #

START



STOP

REC

RECORDER

Preparation

If you will be using sheet music with your

Clavinova, raise the music stand built into its top

panel by lifting the rear edge of the music stand,

then flip down the music stand braces and engage

them with the corresponding recesses.

The music stand can be lowered after slightly

lifting it and folding the two brackets which sup-

port it against the back of the stand.

To open the CLP-555 key cover lift it just

enough to clear the keys (do not lift excessively)

then slide the cover back into the main unit. To

close the cover slide it forward all the way and then

lower it gently until it closes completely.

The Music Stand.............................................................................................................................................................................

The Key Cover...................................................................................................................................................................................

Opening and Closing the Lid...........................................................................................................................................

• Hold the cover with both hands when moving it, and

do not release it until it is fully opened or closed. Be

careful to avoid catching fingers (yours or others)

between the cover and main unit.

• Do not place objects on top of the key cover. Small

objects placed on the key cover may fall inside the

main unit when the cover is opened.

Z Raise the music stand as described in “The

Music Stand”, above.

X Raise and hold the right side of the lid (viewed

from the keyboard end of the instrument).

C Raise the lid stay and carefully lower the lid so

that the end of the stay fits into the recess in

the lid.

• Make sure that the end of the stay fits securely in

the lid recess. If the stay is not properly seated in

the recess the lid may fall causing damage or injury.

• Be careful that you or others do not bump the stay

while the lid is raised. The stay may be bumped out

of the lid recess causing the lid to fall.

• Be careful not to catch your fingers when raising or

lowering the lid.

Be careful of fingers when opening or closing.

Connections

1 AUX IN L/L+R and R Jacks

These jacks are intended for use with an external tone generator mod-

ule such as the Yamaha DOU-10 Disk Orchestra Unit. The stereo outputs

from the external tone generator module are connected to the AUX IN L/

L+R and R jacks, allowing the sound of the tone generator to be repro-

duced via the Clavinova’s internal sound system and speakers. A line-level

mono source can be connected to the L/L+R jack.

• The input signal from the AUX IN jacks is delivered to the AUX OUT jacks,

but is not affected by the Clavinova’s volume control or reverb effect.

2 AUX OUT L/L+R and R Jacks

The AUX OUT L/L+R and R jacks deliver the output of the Clavinova for

connection to an instrument amplifier, mixing console, PA system, or record-

ing equipment. If you will be connecting the Clavinova to a monaural sound

system, use only the L/L+R jack. When a plug is inserted into the L/L+R jack

only, the left- and right-channel signals are combined and delivered via the L/

L+R jack so you don’t lose any of the Clavinova’s sound.

• The AUX OUT jack signal must never be returned to the AUX IN jacks, either

directly or through external equipment.

3 MIDI IN, THRU and OUT Connectors

The MIDI IN connector receives MIDI data from an external MIDI

device (such as the DOU-10 Disk Orchestra Unit) which can be used to

control the Clavinova. The MIDI THRU connector re-transmits any data

received at the MIDI IN connector, allowing “chaining” of several MIDI

instruments or other devices. The MIDI OUT connector transmits MIDI

data generated by the Clavinova (e.g. note and velocity data produced by

playing the Clavinova keyboard).

More details on MIDI are given in “MIDI FUNCTIONS” on page 28.

4 TO HOST Connector & HOST SELECT Switch

This jack and selector switch allow direct connection to a personal

computer for sequencing and other music applications — without the need

for a separate MIDI interface. See page 32 for details.

● PHONES Jacks

(Bottom Panel)

Two pairs of standard pair of stereo headphones can be plugged in here

for private practice or late-night playing. The internal speaker system is

automatically shut off when a pair of headphones is plugged into either of

the PHONES jacks.

Tone Generator

AUX OUT

L+R

DOU-10

MIDI

IN OUT THRU

Personal Computer

HOST SELECT TO HOST

PC-2 PC-1

Mac

MIDI

Stereo System

DOU-10

AUX IN

L+R

Bottom Panel

MIDI

AUX IN

HOST SELECT TO HOST

IN OUT

L+R

THRU

PC-2 PC-1

Mac

MIDI

AUX OUT

L+R

Selecting & Playing Voices

Turn Power On...................................................................................................

After making sure that the Clavinova’s AC cord is properly plugged

into the Clavinova itself and plugged into a convenient AC wall outlet,

press the [POWER] switch located to the left of the keyboard to turn

the power ON.

When the power is turned ON, one of the voice selector LEDs will

light.

Set the Volume ..................................................................................................

Initially set the [MASTER VOLUME] control about half way

between the “MIN” and “MAX” settings. Then, when you start playing,

re-adjust the [MASTER VOLUME] control for the most comfortable

listening level.

Select a Voice .....................................................................................................

Select the desired voice by pressing one of the voice selectors. Use

the [VARIATION] button to select a variation of the current voice, as

required.

POWER

MASTER VOLUME

MAX

MIN

VARIATION

PIANO 1

PIANO 2 CLAVI.TONE E.PIANO 1 E.PIANO 2

STRINGS

HARPSI-

CHORD

PIPE

ORGAN 1

PIPE

ORGAN 2

Play................................................................................................................................

The Clavinova also offers keyboard touch response, so the volume

and timbre of notes played can be controlled according to how “hard”

you play the keys. The amount of variation available depends on the

selected voice.

Add Effects As Required.......................................................................

You can also change add reverb and/or a chorus effect as desired by

using the [REVERB] and [EFFECT] buttons (see page 14 for [RE-

VERB] button operation, and page 15 for [EFFECT] button opera-

tion).

REVERB

ROOM

HALL 1

HALL 2

STAGE

EFFECT

Demonstration tunes are provided that effectively demonstrate each of the

Clavinova’s voices. There are also 30 piano songs that you can play individually,

all in sequence, or in random order. Here’s how you can select and play the

demo tunes.

Playing the Demonstration Tunes

Engage the Demo Mode .........................................................................

Play a Voice Demo or Piano Song ...............................................

● Voice Demo Playback

Press one of the voice selectors to start playback of the corresponding voice

demo tune — featuring the voice normally selected by that voice selector

button. The indicator of the selected voice selector button will flash during

playback, and “---” (relative tempo) will appear on the LED display. You can

start playback of any other voice demo tune during playback by simply

pressing the corresponding voice selector. You can stop playback at any time

by pressing the [START/STOP] button, the voice selector of the currently

playing demo.

● Piano Song Playback

To play any of the 30 piano songs provided, use the [TEMPO/SONG] buttons to

select the number of the tune you want to play (the number will appear on the

LED display), then press the [START/STOP] button. Playback will stop automati-

cally when playback of the selected piano song has finished. To randomly select

and play one of the piano songs press the [VARIATION] button while playback is

stopped.

Select “ALL” instead of a number to play all piano songs and voice demo

tunes in sequence, or select “rnd” to continuously play all piano songs and

voice demo tunes in random order. The [VARIATION] button indicator will

flash during playback. Press the [START/STOP] button to stop playback. If a

voice selector is pressed while “ALL” is showing on the display, playback will

begin from the corresponding song.

• While a voice demo or piano song is playing, you can use the [TEMPO/

SONG] buttons to adjust the playback tempo as required. This produces a

relative tempo variation, with a range from “-99” through “---” to “99”.

• Use the [MASTER VOLUME] control to adjust the volume.

• The demo mode cannot be engaged while the recorder (page 19) is in

use.

• The default tempo is automatically selected whenever a new song is

selected, or playback of a new song begins during “

ALL

” or “

rnd

”

playback.

• No MIDI reception occurs in the demo mode.

• The demo/piano song data is not transmitted via the MIDI connectors.

* See page 48 for a complete listing of the demo tunes.

Press the [DEMO/PIANO SONG] button to engage the demo mode

— the voice selector indicators will flash in sequence.

VARIATION

PIANO 1

PIANO 2 CLAVI.TONE E.PIANO 1 E.PIANO 2

STRINGS

HARPSI-

CHORD

PIPE

ORGAN 1

PIPE

ORGAN 2

Exit From the Demo Mode....................................................................

After stopping demo playback, press the [DEMO/PIANO SONG]

button to exit from the demo mode and return to the normal play mode.

DEMO



PIANO SONG

DEMO



PIANO SONG

TEMPO/

SONG

–

YES

START



STOP

Piano Song A-B Repeat

The A-B Repeat function can be used to continuously repeat a

specified phrase within a piano song. Combined with the Part Cancel

function described below, this provides an excellent way to practice

difficult phrases.

Specify the Beginning (A) of the Phrase..............................

Select and play a piano song, then press the [FUNCTION] button at

the beginning of the phrase you want to repeat. This sets the “A” point

(“A-” will appear on the display).

To set the “A” point at the very beginning of the song, press the

[FUNCTION] button before starting playback.

Specify the End (B) of the Phrase ...............................................

Press the [FUNCTION] button a second time at the end of the

phrase. This sets the “B” point (“A-b” will appear on the display). At

this point repeat playback will begin between the specified A and B

points.

Stop Playback....................................................................................................

Press the [START/STOP] button to stop playback while retaining

the specified A and B points. A-B repeat playback will resume if the

[START/STOP] button is then pressed again.

To cancel the A and B points press the [FUNCTION] button once.

• The A and B points are automatically canceled when a new song is

selected.

• The A-B Repeat function cannot be used during “

ALL

” or “

rnd

” playback.

Playing the Demonstration Tunes

FUNCTION

START



STOP

REC

RECORDER

Piano Song Part Cancel

The 30 piano songs have separate left- and right-hand parts that can

be turned on and off as required so you can practice the corresponding

part on the keyboard. The right-hand part is played by the recorder’s [1]

track, and the left-hand part is played by recorder’s [2] track.

Turn the Desired Part Off.......................................................................

Press the RECORDER [1] or [2] button to turn the corresponding

part off — the corresponding indicator will go out (these buttons

alternately toggle the corresponding part on and off).

• The parts can be turned on or off even during playback.

• The Piano Song Part Cancel function cannot be used during “

ALL

” or

“

rnd

” playback.

• The “Piano Song Part Cancel Volume” function described on page 27 can

be used to set the canceled part so that it plays at a volume from “0” (no

sound) to “20”. The default setting is “5”.

• Both parts are automatically turned ON whenever a new song is selected.

Playing the Demonstration Tunes

START



STOP

REC

RECORDER

Start/Stop Playback.....................................................................................

Press the [START/STOP] button to start and stop playback as

required.

START



STOP

REC

RECORDER

Synchro Start .....................................................................................................

When the Synchro Start function is engaged, playback of the se-

lected piano song will begin automatically as soon as you start playing

on the keyboard.

To engage the Synchro Start function press the [START/STOP]

button while holding the part button corresponding to the part which is

ON. The rightmost dot on the display will light. Playback will then start

as soon as you begin playing on the keyboard.

• If you hold a track button which is OFF while pressing the [START/STOP]

button, that track will be turned ON and the Synchro Start mode will be

engaged.

START



STOP

REC

RECORDER

Left Pedal Start/Stop..................................................................................

The left pedal can be assigned to start and stop piano song playback

via the “Left Pedal Mode” function described on page 27.

The Dual Mode

The dual mode makes it possible to play two voices simultaneously across

the entire range of the keyboard.

To activate the dual mode simply press two voice selectors at the

same time (or press one voice selector while holding another). The

voice indicators of both selected voices will light when the dual mode is

active. To return to the normal single-voice play mode, press any single

voice selector.

• The dual and split modes cannot be engaged at the same time.

• The [VARIATION] button indicator will light if the variation is engaged for

either or both of the dual-mode voices. While the dual mode is engaged

the [VARIATION] button can be used to turn the variation for both voices

on or off. To use the variation for only one of the voices the setting must

be made prior to engaging the dual mode.

• The chorus effect will apply to both the dual mode voices as specified

after engaging the dual mode (the default effect on/off and depth settings

are different for each voice combination). The effect depth for the dual

mode voices can be individually set via the Dual Mode “1st Voice Effect

Depth” and “2nd Voice Effect Depth” functions described on page 25.

IANO 1 E.PIANO 2

HARPSI-

CHORD

Other Dual Mode Functions...............................................................

The CLP-555 Function mode provides access to a number of other

dual-mode functions, listed below. See the corresponding pages for

details.

• Dual Balance..........................................24

• Dual Detune ...........................................24

• 1st Voice Octave Shift............................. 24

• 2nd Voice Octave Shift ........................... 24

• 1st Voice Effect Depth ............................ 25

• 2nd Voice Effect Depth ...........................25

• Slow-attack Strings.................................25

• Reset......................................................25

The Split Mode

The split mode makes it possible to play two different voices on the keyboard

— one with the left hand and another with the right hand. The left-hand voice is

played on all keys to the left of (and including) a specified “split point” key, while

the right-hand voice is played on all keys to the right of the split point key.

To activate the split mode simply press the [SPLIT] button so thats

indicator lights. The split mode can be turned off at any time by press-

ing the [SPLIT] button again so that its indicator goes out.

• The dual and split modes cannot be engaged at the same time.

Selecting the Left-hand Voice...........................................................

The voice that was selected before the split mode was engaged

becomes the right-hand voice in the split mode. To select a left-hand

voice press the corresponding voice selector while holding the [SPLIT]

button. The indicator of the left-hand voice selector will light while it is

pressed, then only the right-hand voice selector and [SPLIT] button

indicators will remain lit.

• The variation can be individually turned on and off for the split mode

voices. Normally the voice indicator of the right-hand voice lights in the

split mode. The [VARIATION] can be used to turn the variation for the

right-hand voice on or off as required. While the [SPLIT] button is held,

however, the voice indicator of the left-hand voice lights, and in this state

the [VARIATION] button can be used to turn the variation for the left-hand

voice on or off as required.

• The chorus effect will apply to both the split mode voices as specified

after engaging the split mode (the default effect on/off and depth settings

are different for each voice combination). The effect depth for the split

mode voices can be individually set via the Split Mode “Left Voice Effect

Depth” and “Right Voice Effect Depth” functions described on page 26.

SPLIT

O 2

STRINGS

HARPSI-

CHORD

SPLIT

Setting the Split Point...............................................................................

The split point is initially set at the F#2 key by default. You can reset

the split point to any other key by pressing the key while holding the

[SPLIT] button (the name of the current split-point key appears on the

LED display while the [SPLIT] button is held). The split point can also

be set via the Function mode (see below).

Other Split Mode Functions...............................................................

The CLP-555 Function mode provides access to a number of other

split-mode functions, listed below. See the corresponding pages for

details.

• Split Point ...............................................25

• Split Balance ..........................................26

• Right Voice Octave Shift ......................... 26

• Left Voice Octave Shift ........................... 26

• Right Voice Effect Depth.........................26

• Left Voice Effect Depth ...........................26

• Damper Mode ........................................26

• Reset......................................................26

SPLIT

A-1 b=1 C 2 F~2

A-1 Bb-1 C2 F#2

Example:

Reverb

The [REVERB] button selects a number of digital reverb effects that you can

use for extra depth and expressive power.

To select a reverb type press the [REVERB] button a few times until

the indicator corresponding to the desired type lights (the indicators

light in sequence each time the [REVERB] button is pressed). No

reverb is produced when all indicators are off.

OFF

No reverb effect is selected when no REVERB indicator is lit.

ROOM

This setting add a continuous reverb effect to the sound that is similar

to the type of acoustic reverberation you would hear in a medium-size

room. This is the default reverb setting.

HALL 1

For a “bigger” reverb sound, use the HALL 1 setting. This effect

simulates the natural reverberation of a medium-size concert hall.

HALL 2

For a really spacious reverb sound, use the HALL 2 setting. This effect

simulates the natural reverberation of a large concert hall.

STAGE

A simulation of the type of reverb produced in a stage environment.

Adjusting Reverb Depth.........................................................................

The depth of the selected reverb effect can be adjusted for the

current voice by using the [–/NO] and [+/YES] buttons while holding

the [REVERB] button. The depth range is from 0 through 20 (the

current depth setting appears on the LED display while the [REVERB]

button is held). A setting of “0” produces no effect, while a setting of

“20” produces maximum reverb depth. Press the [–/NO] and [+/YES]

buttons simultaneously while holding the [REVERB] button to recall

the default setting: “10”.

• The reverb type and depth settings affect all voices.

REVERB

ROOM

HALL 1

HALL 2

STAGE

REVERB

ROOM

HALL 1

HALL 2

STAGE

TEMPO/

SONG

–

YES

The Chorus Effect

The [EFFECT] button engages a chorus effect that can give your sound

greater depth and animation.

The [EFFECT] button turns the chorus effect on (indicator lit) and

off (indicator off).

• The default effect on/off settings are different for each voice.

Adjusting Effect Depth.............................................................................

While the chorus effect is on the effect depth can be individually

adjusted for the selected voice by using the [–/NO] and [+/YES]

buttons while holding the [EFFECT] button. The depth range is from 0

through 20 (the current depth setting appears on the LED display while

the [EFFECT] button is held). A setting of “0” produces no effect,

while a setting of “20” produces maximum effect depth. Press the

[–/NO] and [+/YES] buttons simultaneously while holding the [EF-

FECT] button to recall the default setting for the current voice (the

default depth settings are different for each voice).

The Pedals

Soft (Left) Pedal...............................................................................................

The soft pedal reduces the volume and slightly changes the timbre of

notes played while the pedal is pressed. The soft pedal will not affect

notes which are already playing when it is pressed.

The left pedal can also be assigned to song start/stop operation via

the “Left Pedal Mode” described on page 27.

The CLP-555 has three foot pedals that produce a range of expressive ef-

fects similar to those produced by the pedals on an acoustic piano.

Damper (Right) Pedal ................................................................................

The damper pedal functions in the same way as a damper pedal on

an acoustic piano. When the damper pedal is pressed notes played have

a long sustain. Releasing the pedal immediately stops (damps) any

sustained notes.

TEMPO/

SONG

–

YES

EFFECT

Sostenuto (Center) Pedal......................................................................

If you play a note or chord on the keyboard and press the sostenuto

pedal while the note(s) are held, those notes will be sustained as long as

the pedal is held (as if the damper pedal had been pressed) but all

subsequently played notes will not be sustained. This makes it possible

to sustain a chord, for example, while other notes are played “staccato.”

Soft pedal

Damper pedal

Sostenuto pedal

Touch Sensitivity

Four different types of keyboard touch sensitivity — HARD, MEDIUM, SOFT

or FIXED — can be selected to match different playing styles and preferences.

To select a touch sensitivity type press the [TOUCH] button a few

times until the indicator corresponding to the desired type lights (the

indicators light in sequence each time the [TOUCH] button is pressed).

HARD

The HARD setting requires the keys to be played quite hard to

produce maximum loudness.

MEDIUM

The MEDIUM setting produces a fairly “standard” keyboard response.

This is the initial factory default setting.

SOFT

The SOFT setting allows maximum loudness to be produced with

relatively light key pressure.

FIXED

All notes are produced at the same volume no matter how hard the

keyboard is played. This is an ideal setting for voices which normally

have no keyboard sensitivity (i.e. harpsichord and organ).

The volume of notes played in the FIXED mode can be set by using

the [–/NO] and [+/YES] buttons while the [TOUCH] button is held (the

current volume level appears on the display). The volume range is

from 1 through 127. The default setting is 64.

Transposition

Use the [–/NO] or [+/YES] button while holding the [TRANS-

POSE] button to transpose down or up as required. The transposition

range is from “–12” (down one octave) through “0” (normal pitch) to

“12” (up one octave). The amount of transposition appears on the LED

display while the [TRANSPOSE] button is held. The default transpose

setting is “0”.

• The [TRANSPOSE] button indicator remains lit when a transpose setting

other than “0” is selected.

• Notes below and above the A-1 … C7 range of the Clavinova sound one

octave higher and lower, respectively.

The Clavinova’s TRANSPOSE function makes it possible to shift the pitch of

the entire keyboard up or down in semitone intervals up to a maximum of 12

semitones (i.e. a maximum of one octave up or down). “Transposing” the pitch of

the Clavinova keyboard facilitates playing in difficult key signatures, and you can

easily match the pitch of the keyboard to the range of a singer or other instru-

mentalist.

HARD

MEDIUM

SOFT

FIXED

TOUCH

TEMPO/

SONG

–

YES

TRANSPOSE

Tuning

Tuning makes it possible to adjust the pitch of the Clavinova over a 427.0 Hz

… 453.0 Hz (corresponding to the A3 note’s Hz) range in approximately 0.2

Hertz intervals. Pitch control is useful for tuning the Clavinova to match other

instruments or recorded music.

Tuning Up ...............................................................................................................

ZTo tune up (raise pitch), hold the A-1 and B-1 keys simultaneously.

XPress any key between C3 and B3. Each time a key in this range is

pressed the pitch is increased by approximately 0.2 Hz.

The [–/NO] and [+/YES] buttons can also be used to tune down or up,

respectively, in 1 Hz increments. Press the [–/NO] and [+/YES] buttons

simultaneously to recall standard tuning (A3 = 440 Hz).

CRelease the A-1 and B-1 keys.

Tuning Down.......................................................................................................

ZTo tune down (lower pitch), hold the A-1 and A#-1 keys simulta-

neously.

XPress any key between C3 and B3. Each time a key in this range is

pressed the pitch is decreased by approximately 0.2 Hz.

The [–/NO] and [+/YES] buttons can also be used to tune down or up,

respectively, in 1 Hz increments. Press the [–/NO] and [+/YES] buttons

simultaneously to recall standard tuning (A3 = 440 Hz).

CRelease the A-1 and A#-1 keys.

To Restore Standard Pitch...................................................................

ZTo restore the default pitch (A3 = 440 Hz), hold the A-1, A#-1 and

B-1 keys simultaneously.

XPress any key between C3 and B3.

CRelease the A-1, A#-1 and B-1 keys.

-1

TEMPO/

SONG

–

YES

-1

TEMPO/

SONG

–

YES

In terms of “Hertz”, the overall tuning range is from 427.0 Hz to 453.0

Hz. The current tuning setting is shown on the LED display while the tuning

is being adjusted. Tenths of a Hertz are indicated on the LED display by the

appearance and position of one or two dots, as in the following example:

• An alternative tuning method is available in the Function mode — page 23.

• The keyboard method of pitch control, described above, has no effect when

LOCAL OFF is active (see “MIDI FUNCTIONS,” page 28).

Display Value

440 440.0

4.40 440.2

44.0 440.4

440. 440.6

4.40. 440.8

The Metronome & Tempo Control

The CLP-555 built-in metronome is a convenient feature for practice, and it

can also provide a solid rhythmic guide when recording using the Recorder

feature, described below.

The Metronome

The metronome sound is alternately turned on and off by pressing

the [METRONOME] button. When on, the beat indicator flashes at the

current tempo.

Metronome Volume ......................................................................................

The volume of the metronome sound can be adjusted by using the

[–/NO] and [+/YES] buttons while holding the [METRONOME]

button. The volume range is from 1 through 20 (the current volume

setting appears on the LED display while the [METRONOME] button

is held). A setting of “1” produces minimum sound, while a setting of

“20” produces maximum metronome volume. Press the [–/NO] and [+/

YES] buttons simultaneously while holding the [METRONOME]

button to recall the default setting: “10”.

Other Metronome Functions .............................................................

The time signature (“beat”) of the metronome can be changed via

the metronome “Beat” function in the Function mode — page 27. The

Function mode also has an alternative method for adjusting the metro-

nome volume — page 27.

Tempo Control

The tempo of the metronome and recorder playback (the recorder is

described in the next section) can be set from 32 to 280 beats per

minute by using the [TEMPO/SONG t/s] buttons. The [t] button

decreases the tempo and the [s] button increases the tempo. The

selected tempo appears on the LED display in the normal play mode

and while the [TEMPO/SONG t/s] buttons are being used to adjust

the tempo. The default tempo (120 or the recorded song tempo when

the recorder contains data and the playback track lamp is lit) can be

recalled by simultaneously pressing the [t] and [s] buttons.

TEMPO/

SONG

–

YES

METRONOME

TEMPO/

SONG

–

YES

METRONOME

Beat indicator

La page charge ...

Yamaha CLP555 Manuel utilisateur

Marque: Yamaha

Modèle: CLP555

Catégorie: Instruments de musique

Taper: Manuel utilisateur

Ce manuel convient également à

CLP-555

Télécharger le PDF

rapport

dans d''autres langues

italiano: Yamaha CLP555 Manuale utente
English: Yamaha CLP555 User manual
español: Yamaha CLP555 Manual de usuario
Deutsch: Yamaha CLP555 Benutzerhandbuch
русский: Yamaha CLP555 Руководство пользователя
Nederlands: Yamaha CLP555 Handleiding
português: Yamaha CLP555 Manual do usuário
dansk: Yamaha CLP555 Brugermanual
polski: Yamaha CLP555 Instrukcja obsługi
čeština: Yamaha CLP555 Uživatelský manuál
svenska: Yamaha CLP555 Användarmanual
Türkçe: Yamaha CLP555 Kullanım kılavuzu
suomi: Yamaha CLP555 Ohjekirja
română: Yamaha CLP555 Manual de utilizare

Yamaha CLP555 Manuel utilisateur

Ce manuel convient également à

Yamaha CLP555 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents