Fisher Paykel CG365DLPRX2_N 36 Inch Flush Fit Gas on Steel Cooktop Guide d'installation

Marque: Fisher Paykel

Modèle: CG365DLPRX2_N 36 Inch Flush Fit Gas on Steel Cooktop

Taper: Guide d'installation

GAS COOKTOP

CG365DW models

INSTALLATION GUIDE

US CA

590686 D 08.17

9 SECURE TO COUNTERTOP WITH BRACKETS BASED ON THE COUNTERTOP THICKNESS

!0 GAS CONNECTION

Place the cooktop into the cutout and

tighten it with the supplied clamps. These

will cope with the countertop thicknesses

3/4”- 2” (19 - 50 mm)when used in the two

orientations shown.

IMPORTANT! - Do not over tighten.

REPEAT ON ALL THE OTHER SIDES

(Total 6 brackets)

3/4” - 2”

(19 mm - 50 mm)

● Make sure the connection point will be accessible with the cooktop installed.

● To enable the gas supply to be readily shut off by the customer, make sure the connection is fitted with an isolating valve

close to the cooktop.

● The appliance must be isolated from the gas supply piping system by closing its individual shut-off valve during any pressure testing of the

gas supply piping system at test pressures at or less than 1/2 p.s.i. (3.5 kPa).

● Maximum inlet gas supply pressure 20” W.C. (5 kPa). Minimum gas supply pressure for regulator testing 5” W.C. Natural Gas / 12” W.C LP

gas.

● A manual shut-off valve must be installed in an accessible location in the gas line external to the appliance for the purpose of turning on or

shutting off gas to the appliance. (In Massachusetts, such shut-off devices should be approved by the Board of State Examiners of Plumbers

& Gas Fitters).

● Gas connection to the product must use the nipple supplied with a 1/2” NPT external thread. The supplied gas pressure regulator must be

installed where it will be accessible for adjustment. The metal flexible hose used must be new, CSA or UL-approved, and must have a 1/2”

NPT external thread on one end and a 1/2” NPT one on the other

If connecting the gas with a flexible hose

● Ensure the hose is long enough to allow for removal of cooktop for servicing.

● Make sure the connector is located as shown in step 5 CLEARANCE DIMENSIONS.

● The hose assembly must be with an Rp 1/2” (ISO 7-1) female thread connection.

● The hose assembly must be as short as practicable and comply with the relevant requirements.

● The hose must not be kinked, subjected to abrasion or permanently deformed.

● The hose must not be near or in contact with any hot surfaces (e.g. base of metal hotlplate, flue, or chassis of undercounter oven etc.)

!6 FINAL CHECKLIST

TO BE COMPLETED BY THE INSTALLER

Have you installed the clamping brackets?

Have you verified that the type of model (factory-set for NG or LP) matches the type of gas at the site of installation?

Have you sealed all connections with gas tape?

Have you leak-tested all connections?

Is the cooktop set to the correct working pressure?

Have you affixed the supplied duplicate data plate label on an adjacent

surface accessible to the customer?

Is the cooktop grounded?

Check that the power supply cord is NOT touching the cooktop.

OPERATION:

Do all burners ignite both individually and in combination?

Are the flames consistent and appropriately sized?

Have you demonstrated the basic operation to the customer?

Complete and keep for safe reference:

Model

Serial No.

Purchase Date

Purchaser

Dealer Address

Installer’s Name

Installer’s Signature

Installation Company

Installation Date

SURFACE DE CUISSON AU GAZ

Modèles CG365DW

INSTRUCTIONS D’INSTALLATION

590686D 08.17

La page est en cours de chargement...

Fisher Paykel CG365DLPRX2_N 36 Inch Flush Fit Gas on Steel Cooktop Guide d'installation

Marque: Fisher Paykel

Modèle: CG365DLPRX2_N 36 Inch Flush Fit Gas on Steel Cooktop

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Fisher Paykel CG365DLPRX2_N 36 Inch Flush Fit Gas on Steel Cooktop Installation guide