Zephyr ZPO-E36AS Manuel utilisateur

www.zephyronline.com

PODESTÁ

ZPO-E30AS

ZPO-E36AS

RANGE HOOD - Installation instructions

ENGLISH..........................3

FRANÇAIS.......................22

Table of Contents

SAFETY INSTRUCTIONS ................................................................................................ pag. 4

LIST OF MATERIALS ......................................................................................................... pag. 9

DUCTING CALCULATION SHEETS .................................................................................... pag. 10

HOOD SPECIFICATION .................................................................................................. pag. 11

INSTALLATION

- POWER SUPPLY CONNECTION ............................................................ pag. 12

- INSTALLATION ..................................................................................... pag. 13

- DUCTING OPTIONS ................................................................................... pag. 14

- MOUNTING THE RANGE HOOD ........................................................... pag. 15

TOUCH CONTROL ............................................................................................................ pag. 16

MAINTENANCE ............................................................................................................... pag. 17

WIRING DIAGRAMS ...................................................................................................... pag. 18

LIST OF PARTS AND ACCESSORIES ....................................................................... pag. 19

WARRANTY ...................................................................................................................... pag. 20

- 3 -

Safety instructions 1/5

IMPORTANT SAFETY INSTRUCTIONS

FOR RESIDENTIAL USE ONLY

READ AND SAVE THESE INSTRUCTIONS

PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.

IMPORTANT: Save these Instructions for the Local Electrical Inspectors use.

INSTALLER: Please leave these Instructions with this unit for the owner.

OWNER: Please retain these instructions for future reference.

Take care when using cleaning agents or detergents.

Suitable for use in household cooking area.

WARNING - To reduce the risk of re or electric shock, do not use this fan with

any Solid-State Speed Control Device.

CAUTION - To reduce risk of re and to properly exhaust air, be sure to duct

air outside – Do not vent exhaust air into spaces within walls or ceilings or into

attics, crawl spaces, or garages.

CAUTION - For general ventilating use only. Do not use to exhaust hazardous

or explosive materials and vapors.

CAUTION - To avoid motor bearing damage and noisy and/or unbalanced im-

pellers, keep drywall spray, construction dust, etc. o power unit.

CAUTION - Please read specication label on product for further information

and requirements.

WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

A. Use this unit only in the manner intended by the manufacturer. If you have

questions, contact the manufacturer.

B. Before servicing or cleaning unit, switch power o at service panel and lock

the service disconnecting means to prevent power from being switched on

accidentally. When the service disconnecting means cannot be locked, secure-

ly fasten a prominent warning device, such as a tag, to the service panel.

C. To reduce the risk of re, electric shock or injury to persons, do not use replace-

ment parts that have not been recommended by the manufacturer (e.g. parts

made at home using a 3D printer).

- 4 -

Safety instructions 2/5

WARNING - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

A. Never leave surface units unattended at high settings. Boilovers cause smok-

ing and greasy spillovers that may ignite. Heat oils slowly on low or medium

settings.

B. Always turn hood ON when cooking at high heat or when ambeing foods

( i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambè ).

C. Clean ventilating fans frequently. Grease should not be allowed to accumulate

on fan or lter.

D. Use proper pan size. Always use cookware appropriate for the size of the

surface element.

E. Keep fan, lters and grease laden surface clean.

F. Use high range setting on range only when necessary. Heat oil slowly on low

to medium setting.

G. Don’ t leave range unattended when cooking.

H. Always use cookware and utensils appropriate for the type and amount o

food being prepared.

WARNING – TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A

RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWINGa:

A. SMOTHER FLAMES with a close-tting lid, cookie sheet, or metal tray, then

turn o the burner. BE CAREFUL TO PREVENT BURNS. If the ames do not go

out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.

B. NEVER PICK UP A FLAMING PAN – You may be burned.

C. DO NOT USE WATER, including wet dishcloths or towels – a violent steam ex-

plosion will result.

D. Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to

operate it.

2. The re is small and contained in the area where it started.

3. The re department is being called.

4. You can ght the re with your back to an exit.

aBased on “kitchen resafety tips” published by NFPA

Proper maintenance of the Range Hood will assure proper performance of

the unit.

INSTALLATION INSTRUCTIONS

WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

- 5 -

Safety instructions 3/5

A. Installation work and electrical wiring must be done by qualied person(s) in

accordance with all applicable codes and standards, including re-rated con-

struction.

B. Sucient air is needed for proper combustion and exhausting of gases through

the ue (chimney) of fuel burning equipment to prevent back drafting. Follow

the heating equipment manufacturer’s guideline and safety standards such as

those published by the National Fire Protection Association (NFPA), and the

American Society for Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

C. When cutting or drilling into wall or ceiling, do not damage electrical wir-

ing and other hidden utilities.

D. Ducted fans must always be vented to the outdoors.

E. This unit must be grounded.

WARNING - TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

WARNING - UNDER CERTAIN CIRCUMSTANCES DOMESTIC APPLIANCES MAY

BE DANGEROUS.

A. Do not check lters with hood working.

B. Do not touch the lamps after a prolonged use of the appliance.

C. No food must be cooked ambè underneath the hood.

D. The use of an unprotected ame is dangerous for the lters and could cause

res.

E. Watch constantly the fried food in order to avoid the cooking oil ares up.

F. Before performing any mainteinance operation, disconnect the hood from

the electrical service.

The manufacturers will not to accept any responsibility for eventual damages,

because of failure to observe the above instructions.

Electrical Requirements

Important:

- Observe all governing codes and ordinances.

- It is the customer’s responsibility to be aware of these below:

- To contact a qualied electrical installer.

- To assure that the electrical installation is adequate and in conformance with

National Electrical Code, ANSI/NFPA 70 latest edition* or CSA standards C22.1-

94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and

all local codes and ordinances.

- If codes permit and a separate ground wire is used, it is recommended that a

qualied electrician determine that the ground path is adequate.

- 6 -

Safety instructions 4/5

- Do not ground to a gas pipe.

- Check with a qualied electrician if you are not sure the range hood is pro-

perly grounded.

- Do not have a fuse in the neutral or ground circuit.

- This appliance requires a 120V 60Hz electrical supply and connected to an

individual properly grounded branch circuit protected by a 15 or 20 ampere

circuit breaker or time delay fuse. Wiring must be 2 wire with ground. Please

also refer to Electrical Diagram on product.

- A cable locking connector (not supplied) might also be required by local co-

des. Check with local requirements, purchase and install appropriate connector

if necessary.

* National Fire Protection Association Batterymarch Park, Quincy, Massachusetts

02269

** CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575

Federal Communication Commission Interface Statement

- This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation.

- This equipment generates, uses and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that in-

terference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined

by turning the equipment o and on, the user is encouraged to try to correct

the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit dierent from that to which

the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

SAFETY PRECAUTION

1. Take care when the cooker hood is operating simultaneously with an open

fireplace or burner that depend on the air in the environment and are supplied by

other than electrical energy, as the cooker hood removes the air from the environ-

ment which a burner or fireplace need for combustion. The negative pressure in

the environment must not exceed 4Pa (4x10-5 bar). Provide adequate ventilation

in the environment for a safe operation of the cooker hood. Follow the local laws

applicable for external air evacuation.

- 7 -

Safety instructions 5/5

Before connecting the model to the electricity network:

- Control the data plate (positioned inside the appliance) to ascertain that the volt-

age and power correspond to the network and the socket is suitable. If in doubt

ask a qualified electrician.

- If the power supply cable is damaged, it must be replaced with another cable or

a special assembly, which may be obtained direct from the manufacturer or from

the Technical Assistance Centre.

2. Warning!

In certain circumstances electrical appliances may be a danger hazard.

A) Do not check the status of the filters while the cooker hood is operating.

B) Do not touch bulbs or adjacent areas, during or straight after prolonged

use of the lighting installation.

C) Flambè cooking is prohibited underneath the cooker hood.

D) Avoid free flame, as it is damaging for the filters and a fire hazard.

E) Constantly check food frying to avoid that the overheated oil may become

a fire hazard.

F) Disconnect the electrical plug prior to any maintenance.

G) This appliance can be used by children aged from 8 years and above and

persons with reduced physical, sensory or mental capabilities or lack of

experience and knowledge if they have been given supervision or instruction

concerning use of the appliance in a safe way and understand the hazards

involved. Children shall not play with the appliance. Cleaning and user

maintenance shall not be made by children w thout supervision.

H) Young children should be supervised to ensure they do not play with the

appliance.

I) There shall be adequate ventilation of the room when the rangehood is used

at the same time as appliances burning gas or other fuels.

L) There is a risk of fire if cleaning is not carried out in accordance with the

instructions.

INSTALLATION INSTRUCTIONS

• Assembly and electrical connections must be carried out by specialised

personnel.

• Wear protective gloves before proceeding with the installation.

WARNING Prop. 65 Warning for California Residents: This product may

contain chemicals known to the State of California to cause cancer, birth defects,

or other reproductive harm.

- 8 -

Led Light

List of Materials

Control

Electrical

System Box

Duct Cover Bracket

Duct Covers

Hardware

Hybrid Bae Filters

- 9 -

Ducting Calculation Sheet

Duct pieces To tal

Equivalent number

length x used =

3- 1/ 4” x 10”

Rect.,

straight

1 Ft. x ( ) = Ft.

3- 1/ 4” x 10”

Rect. to

6” round

transition

5 Ft. x ( ) = Ft.

3- 1/ 4” x 10”

Rect. to

6” round

transition

900 elbow

20 Ft. x ( ) = Ft.

6”, 7”, 8”, 10”

Round,

900

15 Ft.

x ( ) = Ft.

6”, 7”, 8”, 10”

Round,

450

9 Ft. x ( ) = Ft.

Ft.

6”, 7”, 8”, 10”

Round,

straight

1 Ft. x ( ) = Ft.

Subtotal column 1 =

Duct pieces To tal

Equivalent number

length x used =

6”, 7”, 8”, 10”

Round, wall

cap with

damper

30 Ft. x ( ) = Ft.

Ft.

6”, 7”, 8”, 10”

Round

roof cap

30 Ft. x ( ) = Ft.

Subtotal column 2 =

Subtotal column 1 =

Totalductwork =

Maximum Duct Length: For satisfactory air movement,

the total duct length

should not exceed 150 equivalent feet.

6” round to

3- 1/ 4” x 10”

rect.

transition

1 Ft. x ( ) = Ft.

6” round to

3- 1/ 4” x 10”

rect.

transition

900 elbow

16 Ft. x ( ) = Ft.

7” round to

3 1/ 4” x 10”

rect.

transition

8 Ft. x ( ) = Ft.

7” round to

3- 1/ 4” x 10”

rect.

transition

900 elbow

23 Ft. x ( ) = Ft.

elbow

7” to 6” or

8” to 7” Round

tapered

reducer

25 Ft. x ( ) = Ft.

3- 1/ 4” x 10”

Rect. 900

elbow

15 Ft. x ( ) = Ft.

3- 1/ 4” x 10”

Rect. 450

elbow

9 Ft. x ( ) = Ft.

3- 1/ 4” x 10”

Rect. 900

flat elbow

24 Ft. x ( ) = Ft.

3- 1/ 4” x 10”

Rect.

wall cap

with damper

30 Ft. x ( ) = Ft.

Ft. x ( ) = Ft.

15

6”, 7“, 8”

Round

in-line

damper

- 10 -

4"

X

9 -15/16”

15"

12"

Ducted out Min. 28" - Max 39 3/8”

Non-ducted Min. 32" - Max 43 - 1/2”

16-9/16”

9-1/2”

0 - 11/16”

11-5/8”

11-1/16”

3-3/8”

19-11/16”

11"

10"-1/16

= =

30" - 36"

22"

3 - 9/16”

7 - 5/8”

Ø 6”

front of hood side of hood

top of hood

Hood Specications

back of hood

- 11 -

A B

C D

Installation - Power Supply Connection

GENERAL

• Carefully read the following important information regarding installation

safety and maintenance. Keep this information booklet accessible for further

consultations.

A. Lift the electrical plant box.

B. Remove the 3 fixed screws.

C. Position the electrical box so it is in the line with the holes of the previously removed

screws and tighten.

D 1. Route the power cord to the junction box.

2. Using listed conduit fittings and connectors, connect the power supply to the box and

each line to the appropriate wire following this color convention:

BLACK = HOT LEG

WHITE = NEUTRAL

GREEN/YELLOW = GROUND

Polarity must be observed. Unit must be properly grounded. Use a double throw disconnect

switch.

3. Replace the box cover. Replace the Anti-grease flters.

All wiring must be in compliance with national electrical code, ANSI/NFPA 70-1999 and

all local codes and regulations.

- 12 -

Installation

• Mounting the hood to the wall

Position the xing template on the wall (taking into account the minimum distance

from the hob).

- Drill 4 holes respecting the size indicated on the xing template.

- Fix the appliance to the wall with screws A and align it horizontally with the wall

units. After adjusting the appliance, x the hood permanently with screws B. For the

various installations, use screws and dowels suitable for the type of wall (e.g. rein-

forced concrete, plasterboard, etc.). If screws and dowels are supplied with the prod-

uct, check that they are suitable for the type of wall to which the hood is to be xed.

- Fasten bracket D to the wall so that it is aligned with the hood with screws C .

- Fasten the decorative chimneys to the hood with screws G.

- Slide the upper decorative chimney onto bracket D and fasten it with screws E.

A

E

C

D

G

- 13 -

WARNING FIRE HAZARD

NEVER exhaust air or terminate duct work into spaces between walls, crawl

spaces, ceiling, attics or garages.

All exhaust must be ducted to the outside, unless using the recirculating option.

Use single wall rigid Metal ductwork only.

Fasten all connections with sheet metal screws and tape all joints w/ certied

Silver Tape or Duct Tape.

Some Ducting Options

Installation - Ducting Options

- 14 -

MOUNTING HEIGHTS

The range hood must be installed at a mini-

mum height of 24 inches (61cm) from the

cooking surface. If a connecting duct work

composed of two parts is used, the upper

part must be placed outside the lower part.

Do not connect the range hood duct to the

same duct used to exhaust hot air or fumes

from another appliance. Before proceeding

with the assembly instructions remove the

decorative mesh lters so that the range hood

is easier to handle.

MOUNTING TO THE WALL

1. Place the paper template included with

your hood on the wall to determine where

to add the screws for mounting the hood.

Make sure the bottom of the template

aligns with the bottom of where

the hood will be located. See Fig. 9

2. Lift the hood onto the screws and

adjust to make sure the hood is

level.

3. When the hood has been adjusted

tighten the screws to secure the

hood in place.

NOTE: Screws must be fastened into

wooden studs so wood blocking may

be necessary. If using wall anchors

make sure to check your local codes

for suitability and type of anchors

to use.

NOTE1: For the various installations use screws and screw anchors suited to the

type of wall (minimum screw size: 1/4" diameter x 2-3/4" length).

Min 24" - Max 36"

36"

Installation - Mounting the Range Hood

- 15 -

Touch Control

A – Lights Button: Lights are two level (high, low). From stand-by-on mode,

touch once for high, twice for low, three times to cycle back.

B - Delay O Button: Press the Delay O Button to enable the ten-minute

delay-o function, no matter at what speed the fan is running at. B button will

start blinking indicating the delay o function is enabled. After ten minutes the

fan and lights will turn o. Delay o function can be disabled by pressing B

button, changing the speed, or pressing the Power Button C.

C - Power Button: Press once to activate all button stand by mode allowing

control of other button functions. All buttons will illuminate indicating stand by

mode. Press the Power Button again to turn the hood o (fan and lights). The

stand by mode will remain active for 30 seconds.

D - Low Speed Button: In stand-by mode: Press once for low speed.

E - Medium Speed Button: In stand-by mode: Press once for medium speed.

F - High Speed Button: In stand-by mode: Press once for high speed.

MESH FILTER CLEAN REMINDER (always enabled): after 60 hours of fan usage,

button A blinks when the hood is in stand-by, indicating it is time to clean the

mesh lters. To Reset the function: with the hood in stand-by, press and hold

the B button for 4 to 5 seconds, the A button will stop blinking, and the 60-

hour timer will reset.

CHARCOAL FILTER REPLACE REMINDER (disabled by default, must be enabled

by user if recirculating hood): To enable Charcoal Filter Replacement Function

hold buttons D and F simultaneously for four seconds. The A button will quickly

ash 3 times indicating the Charcoal Filter Replacement Function is enabled. After

200 hours of fan usage, the B button will blink while the hood is on, indicating

it is time to replace the charcoal lters.

To Reset the Charcoal Filter Replace Reminder function: Hold the B button for 4

to 5 seconds until it stops ashing, and the 200-hour timer will reset.

Order replacement charcoal lter kit number Z0F-C011 through your local dealer,

www.zephyronline.com, or the Zephyr customer service department.

To disable the Charcoal Filter Replacement function, repeat the enable procedure,

the A button will illuminate for 3 seconds then turn o indicating the Charcoal

Filter Replacement Function is disabled.

ABCDEF

- 16 -

Maintenance

• It is recommended to operate the appliance prior to cooking. It is recommended

to leave the appliance in operation for 5 minutes after cooking is completed in

order to completely eliminate cooking vapors and odors. The proper function

of the range hood is conditioned by the regularity of maintenance.

• The decorative mesh lters capture the grease particles suspended in the

air and are therefore subject to clogging because of frequent use. In order to

prevent a re hazard, it is recommended to clean the lter a minimum of every

2 months or when instructed by the Metal Filter Clean indicator on the range

hood controls. Clean the range hood by carrying out the following instructions:

- Remove the lters from the range hood and wash them in a solution of water

and neutral liquid detergent, leaving to soak.

- Rinse thoroughly with warm water and leave to dry.

- Filters may also be washed in the dishwasher at the lowest setting.

The lters may alter in color after several washes but is not cause for replacement.

• Clean the blower and other surfaces of the range hood regularly using a cloth

moistened with denatured alcohol or non abrasive liquid detergent.

AIRFLOW CONTROL TECHNOLOGY

Airow Control Technology (ACT™) enables the installer to reduce the maximum

blower CFM to one of two most specied CFM levels; 390 or 290 CFM. The us-

age of ACT may not be necessary for your installation. Please check your local

codes for CFM restrictions.

Setting ACT 390

With the hood o, press buttons E and F simultaneously for approximately 3

seconds. The buttons will ash for 2 seconds to conrm the setting change. The

hood will have 3 fan speeds in ACT 390.

Setting ACT 290

With the hood o, press buttons B and F simultaneously for approximately 3

seconds. The buttons will ash for 2 seconds to conrm the setting change. The

hood will have 2 fan speeds in ACT 290.

Take care when reducing the CFM. After the ACT feature is set, it cannot be

reverted to the default CFM.

- 17 -

Wiring Diagram

INTERNAL BLOWER CIRCUIT DIAGRAM

N

V.A.C.

L

Red N

Black 1°

White 2°

Orange 3°

Red

Black

Brown

Black

White

10W 12V

M

Blue 1°

Grey

White 2°

Orange 3°

Brown

Brown 4°

-+

OUTPUT

INPUT

RedRed Red

Black 4°

Yellow-Green

La1

La2

N

NL

3b 3a

4b 4a 4a

R10

R9

R8 Q2

X19

X17

X2

C1

C3

C4

C5

C6

C7

CN1

CN2

CN3

CN4

CN5

CN6

CN7

CX1

D1

D2

D3

D4

DB1

DB2

F1

K1 K2K3 K4

K5

K6

K7 K8

K9

K10

K11

K12

Q1

Q3

Q4

Q5

Q6

Q7

Q8

Q9

R1

R2

R3

R4

R5

R6

R7

R11

R12

R13

R14

R15

R16

R17

R18

R19

R20

R21

RF1

TR1

U1

U2

VR1

X1

X3X4

X5 X6X7X8 X9X10

X11

X12

X13X14X15

SMPS1

X16

X18

R22

+

-

~~

+

-

3a 2b 2a 2a 1b 1a 1a NN

BlackBlack Black

Light Blue

Red N

- 18 -

DESCRIPTION HOOD PART#

REPLACEMENT PARTS

LED Light 1.3W (each) ZPO Z0B0051

OPTIONAL ACCESSORIES

Recirculating Kit ZPO ZRC-00PO

Replacement Charcoal Filters (2x)ZPO Z0F-C011

Duct Cover Extension, Stainless SteelZPO Z1C-01PO

To order parts, visit us online at http://store.zephyronline.com

List of Parts and Accessories

UL References

LED Light 1.3W (each) SPK8148

Recirculating Kit KIT0I0633

Replacement Charcoal FiltersACK00261

Duct Cover Extension Inox KIT0I0632

SPK9475

SPK8261

- 19 -

ZPO-E30AS

ZPO-E36AS 50210045

50210051

Remote Control ZPO 14000010

TO OBTAIN SERVICE UNDER WARRANTY OR FOR ANY SERVICE RELATED QUESTIONS:

United States Customers please call: 1-888-880-8368 or contact us at: zephyronline.com/contact

Canada Customers please call: 1-800-361-0799 or Email: service@distinctive-online.com

Limited Warranty

Zephyr Ventilation, LLC (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred

to herein as “you” or “your”) of Zephyr products (the “Products”) that such Products will be free from defects in

materials or workmanship as follows:

Two Year Limited Warranty for Parts: For two years from the date of your original purchase of the Products,

we will provide, free of charge, Products or parts (including LED light bulbs, if applicable) to replace those that

failed due to manufacturing defects subject to the exclusions and limitations below. We may choose, in our sole

discretion, to repair or replace parts before we elect to replace the Products.

One Year Limited Warranty for Labor: For one year from the date of your original purchase of the Products, we

will provide, free of charge, the labor cost associated with repairing the Products or parts to replace those that

failed due to manufacturing defects subject to the exclusions and limitations below. After the rst year from the

date of your original purchase, you are responsible for all labor costs associated with this warranty.

Warranty Exclusions: This warranty covers only repair or replacement, at our option, of defective Products or parts

and does not cover any other costs related to the Products including but not limited to: (a) normal maintenance

and service required for the Products and consumable parts such as uorescent, incandescent or halogen light

bulbs, mesh and charcoal lters and fuses; (b) any Products or parts which have been subject to freight damage,

misuse, negligence, accident, faulty installation or installation contrary to recommended installation instructions,

improper maintenance or repair (other than by us); (c) commercial or government use of the Products or use

otherwise inconsistent with its intended purpose; (d) natural wear of the nish of the Products or wear caused

by improper maintenance, use of corrosive and abrasive cleaning products, pads, and oven cleaner products; (e)

chips, dents or cracks caused by abuse or misuse of the Products; (f) service trips to your home to teach you

how to use the Products; (g) damage to the Products caused by accident, re, oods, acts of God; or (h) Custom

installations or alterations that impact serviceability of the Products. If you are outside our service area, additional

charges may apply for shipping costs for warranty repair at our designated service locations and for the travel cost

to have a service technician come to your home to repair, remove or reinstall the Products. After the rst year

from the date of your original purchase, you are also responsible for all labor costs associated with this warranty.

All Products must be installed by a qualied professional installer to be eligible for warranty repairs or service.

Limitations of Warranty. OUR OBLIGATION TO REPAIR OR REPLACE, AT OUR OPTION, SHALL BE YOUR SOLE

AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. WE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUEN-

TIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THE

PRODUCTS. THE EXPRESS WARRANTIES IN THE PRECEDING SECTION ARE EXCLUSIVE AND IN LIEU OF ALL

OTHER EXPRESS WARRANTIES. WE HEREBY DISCLAIM AND EXCLUDE ALL OTHER EXPRESS WARRANTIES FOR

THE PRODUCTS, AND DISCLAIM AND EXCLUDE ALL WARRANTIES IMPLIED BY LAW, INCLUDING THOSE OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

Some states or provinces do not allow limitations on the duration of an implied warranty or the exclusion or

limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.

To the extent that applicable law prohibits the exclusion of implied warranties, the duration of any applicable

implied warranty is limited to the same two-year and one-year periods described above if permitted by applicable

law. Any oral or written description of the Products is for the sole purpose of identifying the Products and shall

not be construed as an express warranty. Prior to using, implementing or permitting use of the Products, you

shall determine the suitability of the Products for the intended use, and you shall assume all risk and liability

whatsoever in connection with such determination. We reserve the right to use functionally equivalent refurbi-

shed or reconditioned parts or Products as warranty replacements or as part of warranty service. This warranty is

not transferable from the original purchaser and only applies to the consumer residence where the Product was

originally installed located in the United States and Canada. This warranty is not extended to resellers.

To Obtain Service Under Limited Warranty: To qualify for warranty service, you must: (a) notify us at the address

or telephone number stated below within 60 days of the discovery of the defect; (b) give the model number and

serial number; and (c) describe the nature of any defect in the Product or part. At the time of the request for

warranty service, you must present evidence of your proof of purchase and proof of the original purchase date. If

we determine that the warranty exclusions listed above apply or if you fail to provide the necessary documentation

to obtain service, you will be responsible for all shipping, travel, labor and other costs related to the services. This

warranty is not extended or restarted upon warranty repair or replacements.

Please check our website for any additional Product information, www.zephyronline.com.

Zephyr, 2277 Harbor Bay Parkway, Alameda, CA 94502

JAN21.0401

- 20 -

La page est en cours de chargement...

Zephyr ZPO-E36AS Manuel utilisateur

Ce manuel convient également à

Zephyr ZPO-E36AS Manuel utilisateur

dans d''autres langues

Documents connexes