Modern Forms WS-W41912 Two If By Sea Mode d'emploi
- Taper
- Mode d'emploi
1
INSTALLATION INSTRUCTIONS
WS-W41912/WS-W41918
Phone (800) 526.2588
Fax (800) 526.2585
!
44 Harbor Park Drive
Port Washington, NY 11050
! !
1600 Distribution Ct
Lithia Springs, GA 30122
!
1750 Archibald Avenue
Ontario, CA 91760
"#$%&#'()*+,)-)*..
• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
• When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
• Retain installation instructions for future maintenance reference.
%$%/&All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product by Modern
Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any
parts are damaged or missing.
0$%#%%%#&Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal
areas clean all external surfaces of the xture once every two weeks with a wet cloth.
0$%/&Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
##%#$%&Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou accessoires non conçus
pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la
garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
%#1%##$%& Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
un chion humide.
:LUH&RQQHFWRU
4W\3FV([WUD
%DFNSODWH6FUHZ
4W\([WUD
5XEEHU*DVNHW
4W\([WUD
ABC
2
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Mar.2020
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTIONS
419-Outdoor Wall Sconce
WS-W41912/WS-W41918
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
FIG. 3 Wiring
FIG. 1 FIG. 2
FIG. 4
PREPARATION
1. Shut off the power at the circuit breaker and remove existing fixture,
including the crossbar.
2. Carefully unpack your new fixture and lay out all the parts on a clear
area. Be careful not to lose any small parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the back plate screw (B) and back plate from the fixture.
4. Secure the back plate to the junction box using standard junction
box screws that comes with the junction box. Note: the side of the
back plate marked “GND” must face out.
CONNECTING THE WIRES (Fig. 3)
5. Connect the fixture’s wires to house wires as shown in Fig.3, making sure that all wire connectors (A) are secured. If your outlet box has a
green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, tuck the fixture’s ground wire directly to the fixture.
After wires are connected, tuck them carefully inside the junction box.
COMPLETING THE INSTALLATION
6. Secure the fixture to the mounting back plate using the back plate screw (B) and rubber gasket (C).
7. To prevent moisture from entering the outlet box and causing a short, use clear caulking (i.e. indoor/outdoor silicone sealant) to outline the
outside of fixture back plate where it meets the wall. Leave a space at the bottom to allow moisture to escape Fig.4.
Junction Box
Wire Connector
Junction Box Screw
Fixture
A
%DFNSODWH6FUHZ
B
5XEEHU*DVNHW
C
%DFNSODWH
Junction Box
Caulking
Back Plate Dimensions
4 1/2"
4 1/8"
1 3/8"
1 3/4"
1
INSTALLATION INSTRUCTIONS
WS-W41925
Phone (800) 526.2588
Fax (800) 526.2585
44 Harbor Park Drive
Port Washington, NY 11050
1600 Distribution Ct
Lithia Springs, GA 30122
1750 Archibald Avenue
Ontario, CA 91760
"#$%&#'()*+,)-)*..
!"!#
$%&''' ( $%
%$%/&)' * ' '''
+,' '+
,'-''&. /
'
0$%#%%%#&0' $%
% $%.1
0$%/&23. 3&/0.- .
(/.4
(563'333433"!#&3%
5%
('&4''/'(*/0'
##%#$%&*'5.633'7'63
.'5'63.'+,''57
''+,''3'34
8/.3'53
%#1%##$%&(95'3%3!
%/95%%.
:
Wire Connector
Qty: 3 pcs+1 Extra
A
Rubber Gasket
Qty: 1 Extra
C
Mounting Screw
Qty: 1 Extra
D
Back plate Screw
Qty: 1 Extra
B
Silicone Pad
E
Qty: 1 pc
2
INSTALLATION INSTRUCTIONS
WS-W41925
Phone (800) 526.2588
Fax (800) 526.2585
44 Harbor Park Drive
Port Washington, NY 11050
1600 Distribution Ct
Lithia Springs, GA 30122
1750 Archibald Avenue
Ontario, CA 91760
22#$%
1. Shut o the power at the circuit breaker and remove existing xture,
including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear
area. Be careful not to lose any small parts necessary for installation.
0"%#$%/#3$4#"53.6
3. Remove the Mounting screws(D) and bottom cap from the xture.
4. Secure the glass into the silicone Pad(E) so the border sits inside the
groove insert into the xture through the bottom of the frame as
shown in Fig.1.
5. Secure the bottom cap to the xture using Mounting screws(D).
6. Remove the back plate screw (B) and back plate from the xture.
7. Secure the back plate to the junction box using standard junction
box screws that comes with the junction box.
Note: the side of the back plate marked “GND” must face out.
%#&(i) using any other non-original-manufacturer provided
junction box screw may result in safety issue;
(ii) The side of the mounting plate marked “GND” must face out.
%%#$%/#$53.76
8. Connect the xture’s wires to junction box wires as shown (Fig. 3). Make
sure that all wire connectors (A) are secure. If your outlet box has a green or
bare copper ground wire, connect the xture’s ground wire to it. Otherwise,
connect the xture’s ground wire directly to the back plate using the GND
screw provided. After wires are connected, tuck them carefully inside the
junction box.
028#$%/#$%#88#$%
9. Secure the xture to the mounting back plate using the back plate
screw (B) and rubber gasket (C).
10. To prevent moisture from entering the outlet box and causing a
short, use clear caulking (i.e. indoor/outdoor silicone sealant) to outline
the outside of xture back plate where it meets the wall. Leave a space
at the bottom to allow moisture to escape (Fig.4).
3$/9
:*2
3$/.
Black or
Smooth
White or
Ribbed
Bare wire
(Ground)
Black
(Hot)
White
(Neutral)
Green or Bare Copper
(Ground)
3$/7.
1 3/4”
5 7/8”
1 3/8”
5 1/2”
3$/ Wire Connector
A
Junction Box
Ground Wire
Rubber Gasket
C
Back plate Screw
B
Junction Box Screw
Hammered Glass
Mounting Screw
D
Bottom Cap
Silicone Pad
Fixture
Silicone Pad
Hammered
Glass
E
Junction Box
Caulking
-
1
-
2
-
3
-
4
Modern Forms WS-W41912 Two If By Sea Mode d'emploi
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
Modern Forms PD-W28515 Balthus Mode d'emploi
-
-
-
-
-
-
-
-
-