Day-Brite CFI FluxPanel LED Install Instructions

Marque: Day-Brite CFI

Modèle: FluxPanel LED

Catégorie: Câbles de signal

Taper: Install Instructions

Ce manuel convient également à

FluxPanel Suspension Bracket

www.day-brite.com www.cﬁ-ligh�ng.com2/5/2019 page 1

443581588890

FLUX PANEL

FLUX PANEL SUSPENSION BRACKET

Figure 1.1

Figure 1.3

1. Unpack suspension kit and make sure all parts are

accounted for. (2 suspension brackets, 12 screws, 2

cross cables, and cable gripper)

2.Unscrew (6) T-grid hooks, Figure 1.1, and discard

each hook including the (2) screws from each.

3. Place the (2) suspension brackets along

the length of the side aligning the holes.

4. Screw the (12) screws included in the kit

in the empty holes. Figure 1.2

5. Attach (2) cross cables and

cable gripper to both ends of the

luminaire by inserting the cross

cable toggles through hanger

holes on the suspension bracket

previously installed. Figure1.3

Figure 1.2 Cable Grippers

Retention Screw

Cable Toggles

CAUTION: THE INSTALLATION AND SERVICING OF THIS PRODUCT SHOULD BE PERFORMED BY A QUALIFIED ELECTRICIAN

OR SERVICE PERSONNEL

ATTENTION : L'INSTALLATION ET L'ENTRETIEN DE CE PRODUIT DOIVENT ÊTRE EFFECTUÉS PAR UN ÉLECTRICIEN OU UN

MEMBRE DU PERSONNEL QUALIFlÉ.

6. Lock cable grippers in place midway between hanging clips by inserting the retention screw

into the bottom of the gripper and tightening loosely. Luminaire can be leveled once it is in

place by sliding cross cables to appropriate balance point. Once luminaire is leveled tighten

retention screw to lock grippers in place.

CAUTION: Electrical luminaires are designed for permanent installation in ordinary (Non-Hazardous) locations in accordance with the National Electrical Code and

all applicable local codes. Do not use in areas of limited ventilation or in high ambient enclosures. The lamp and luminaire operate at high temperatures, contact

with combustible materials can cause fire and personal contact can cause severe burns.

ATTENTION: Ce luminaire a été conçu pour une installation permanente dans un emplacement régulier (non dangereux) et en conformité avec le Code électrique

canadien et codes locaux applicables. Ne jamais installer dans un endroit où la ventilation est limitée au dans des boitiers où la température ambiante est très

élevée. La lampe et le luminaire fonctionnent à des témperatures élevées, un contact avec des matériaux combustibles peut engendrer un incendie et un contact

corporel peut causer de séverès brûlures.

2/5/19 page 2

443581588890

FLUX PANEL

FLUX PANEL SUSPENSION BRACKET

POWER-FEED END OF LUMINAIRE

STEP 1:

Attach bracket and stud to customer supplied junction box.

Attach green ground screw to bracket.

STEP 2:

Support the luminaire approximately 2' below mounting surface.

Once luminaire is supported pass end of power cord through

power feed hole in canopy.

Power Cord

STEP 3:

Make wiring connections to cord leads.

STEP 4:

Insert cable into two piece coupler ensuring that cable terminal

sits in coupler. Slide power feed canopy over stud and screw

coupler to stud. Use outer coupler ring to lock canopy to junction

box.

STEP 5:

Attach strain relief to cord and insert into canopy opening. Allow

approximately 6" of cord above strain relief.

NOTE: For splice inspection the canopy can be dropped away

from junction box by loosening outer coupler ring and dropping

canopy away from ceiling.

ATTACHMENT OF CABLES TO CROSS CABLE GRIPPERS

Ground Screw

Bracket

Threaded Stud

Canopy

Strain Relief

To Fixture

Cable

Coupler

www.day-brite.com www.cﬁ-lighting.com

CAUTION: THE INSTALLATION AND SERVICING OF THIS PRODUCT SHOULD BE PERFORMED BY A QUALIFIED ELECTRICIAN

OR SERVICE PERSONNEL

ATTENTION : L'INSTALLATION ET L'ENTRETIEN DE CE PRODUIT DOIVENT ÊTRE EFFECTUÉS PAR UN ÉLECTRICIEN OU UN

MEMBRE DU PERSONNEL QUALIFlÉ.

CAUTION: Electrical luminaires are designed for permanent installation in ordinary (Non-Hazardous) locations in accordance with the National Electrical Code and all

applicable local codes. Do not use in areas of limited ventilation or in high ambient enclosures. The lamp and luminaire operate at high temperatures, contact with combustible

materials can cause fire and personal contact can cause severe burns.