Axis P3354-V Guide d'installation

INSTALLATION GUIDE

ENGLISH DEUTSCH ITALIANO ESPAÑOL

FRAN

Ç

AIS

AXIS P3353 Network Camera

AXIS P3354 Network Camera

AXIS P3363-V Network Camera

AXIS P3364-V Network Camera

About this Document

This document includes instructions for installing the AXIS

P3353/P3354/P3363-V/P3364-V on your network. Previous

experience of networking will be beneficial when installing

the product.

Legal Considerations

Video and audio surveillance can be prohibited by laws that

vary from country to country. Check the laws in your local

region before using this product for surveillance purposes.

This product includes one (1) H.264 decoder license. To

purchase further licenses, contact your reseller.

Electromagnetic Compatibility (EMC)

This equipment has been designed and tested to fulfill

applicable standards for:

Radio frequency emission when installed according to the

instructions and used in its intended environment.

Immunity to electrical and electromagnetic phenomena

when installed according to the instructions and used in its

intended environment.

USA - Depending on the characteristics of the electrical

environment, using shielded cables (STP) may be

appropriate, in which case the following is applicable: This

equipment has been tested using shielded cables (STP) and

found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful

interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and,

if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or

television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and

receiver.

Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for

help

Canada - This Class B digital apparatus complies with

Canadian ICES-003.

Europe - This digital equipment fulfills the

requirements for RF emission according to the Class B limit

of EN 55022.

This product fulfills the requirements for immunity

according to EN 61000-6-1 residential, commercial and

light-industry environments.

This product fulfills the requirements for immunity

according to EN 61000-6-2 industrial environments.

This product fulfills the requirements for immunity

according to EN 55024 office and commercial

environments.

Japan - B

Australia - This digital equipment fulfills the

requirements for RF emission according to the Class B limit

of AS/NZS CISPR 22.

Equipment Modifications

This equipment must be installed and used in strict

accordance with the instructions given in the user

documentation. This equipment contains no

user-serviceable components. Unauthorized equipment

changes or modifications will invalidate all applicable

regulatory certifications and approvals.

Liability

Every care has been taken in the preparation of this

document. Please inform your local Axis office of any

inaccuracies or omissions. Axis Communications AB cannot

be held responsible for any technical or typographical errors

and reserves the right to make changes to the product and

documentation without prior notice. Axis Communications

AB makes no warranty of any kind with regard to the

material contained within this document, including, but not

limited to, the implied warranties of merchantability and

fitness for a particular purpose. Axis Communications AB

shall not be liable nor responsible for incidental or

consequential damages in connection with the furnishing,

performance or use of this material.

RoHS

This product complies with both the European RoHS

directive, 2002/95/EC, and the Chinese RoHS

regulations, ACPEIP.

WEEE Directive

The European Union has enacted a Directive

2002/96/EC on Waste Electrical and Electronic

Equipment (WEEE Directive). This directive is

applicable in the European Union member states.

The WEEE marking on this product (see right) or

its documentation indicates that the product must not be

disposed of together with household waste. To prevent

possible harm to human health and/or the environment, the

product must be disposed of in an approved and

environmentally safe recycling process. For further

information on how to dispose of this product correctly,

contact the product supplier, or the local authority

responsible for waste disposal in your area.

Business users should contact the product supplier for

information on how to dispose of this product correctly. This

product should not be mixed with other commercial waste.

For more information, visit

www.axis.com/techsup/commercial waste

Support

Should you require any technical assistance, please contact

your Axis reseller. If your questions cannot be answered

immediately, your reseller will forward your queries through

the appropriate channels to ensure a rapid response. If you

are connected to the Internet, you can:

• download user documentation and firmware updates

• find answers to resolved problems in the FAQ database.

Search by product, category, or phrases

• report problems to Axis support by logging in to your

private support area.

ENGLISH

Safeguards

Please read through this Installation Guide carefully before installing the product. Keep the Installation Guide

for further reference.

CAUTION!

• When transporting the Axis product, use the original packaging or equivalent to prevent damage to the

product.

• Store the Axis product in a dry and ventilated environment.

• Avoid exposing the Axis product to vibration, shocks or heavy pressure and do not install the camera on

unstable brackets, unstable or vibrating surfaces or walls, since this could cause damage to the product.

• Only use hand tools when installing the Axis product, the use of electrical tools or excessive force could

cause damage to the product.

• Do not use chemicals, caustic agents, or aerosol cleaners. Use a damp cloth for cleaning.

• Use only accessories that comply with technical specification of the product. These can be provided by Axis

or a third party.

• Use only spare parts provided by or recommended by Axis.

• Do not attempt to repair the product by yourself; contact Axis or your Axis reseller for service matters.

IMPORTANT!

• This Axis product must be used in compliance with local laws and regulations.

• To use this Axis product outdoors, it must be installed in an approved outdoor housing.

Battery replacement

This Axis product uses a 3.0V CR2032 Lithium battery as the power supply for its internal real-time clock (RTC).

Under normal conditions this battery will last for a minimum of 5 years. Low battery power affects the

operation of the RTC, causing it to reset at every power-up. A log message will appear when the battery needs

replacing. The battery should not be replaced unless required!

If the battery does need replacing, please contact www.axis.com/techsup for assistance.

• Danger of Explosion if battery is incorrectly replaced.

• Replace only with the same or equivalent battery, as recommended by the manufacturer.

• Dispose of used batteries according to the manufacturer's instructions.

Cleaning of dome cover

• Be careful not to scratch or damage the dome cover. Do not clean a dome cover that looks clean to the eye

and never polish the surface. Excessive cleaning can damage the surface.

• For general cleaning of a dome cover it is recommended to use a non-abrasive, solvent-free neutral soap or

detergent with water and a soft cloth. Rinse well with clean lukewarm water. Dry with a soft cloth to pre-

vent water spotting.

• Never use harsh detergents, gasoline, benzene or acetone etc. and avoid cleaning in direct sunlight or at

elevated temperatures.

AXIS P33 Network Camera Installation Guide Page 5

ENGLISH

AXIS P3353/P3354/P3363-V/P3364-V Network

Camera Installation Guide

This installation guide provides instructions for installing an AXIS P33 Network Camera on your

network. For all other aspects of using the product, please see the User Manual, available on

www.axis.com

Notes:

• Before you begin, make sure that the package contents, the required cables, tools,

and documentation are available. See

Package contents

below.

• This network camera is intended to operate with PoE; if not available use AXIS PoE Midspan 1 port (not

included).

Package contents

1.

“Package contents”

on page 5

2.

“Hardware overview”

on page 6

3.

“Mount the camera”

on page 7

4.

“Assign an IP address”

on page 8

5.

“Set the password”

on page 11

6.

“Adjust the Lens”

on page 13

7.

“Complete the installation”

on page 14

Item Models/variants/notes

Network camera AXIS P3353, AXIS P3354, AXIS P3363-V

AXIS P3364-V

Dome covers Clear transparent cover

Smoked transparent cover

Labels 2 adhesive serial no. labels

Mounting kit Resitorx screw driver, drill template, terminal block connector

CD AXIS Network Video Product CD including installation tools and other

software

Printed materials Installation Guide (this document)

Axis Warranty Document

AVHS Authentication key

Optional accessories Mounting bracket (region specific)

See www.axis.com for information on available accessories

Page 6 AXIS P33 Network Camera Installation Guide

Hardware overview

Note: AXIS P3353 and AXIS P3354 do not support I/O or audio.

Dimension (HxWxD)

AXIS P3353/AXIS P3354/AXIS P3363-V /AXIS P3364-V = 97 x 148 x 148 mm (3.82 x 5.83 x 5.83")

Weight

AXIS P3353/AXIS P3354 = 430 g (0.9 lb.)

AXIS P3363-V /AXIS P3364-V = 650 g (1.4 lb.)

Network connector

LED indicators

I/O connector

(PoE)

Camera unit

Network cable

Dome cover

out Audio in

SD memory card slot

Wall screws

Audio

Camera unit

Fan output

connector

Built-in microphone

Control button

Camera: P3363/P3364

AXIS P33 Network Camera Installation Guide Page 7

ENGLISH

Mount the camera

This Axis product can be mounted with the cables routed through or along the wall. This product

can also be fitted with a metal conduit for protecting the cabling when they are routed along the

wall. See the illustration that follows.

Mount camera directly onto the wall

1. Using the drill template drill 2 holes in the wall.

2. Route and connect the network cable.

3. Attach the camera unit to the wall using screws and plugs appropriate for the wall material.

Mount camera using a mounting bracket (not included)

1. Using the drill template drill 2 holes in the wall.

2. Route the network cable through the wall and through the holes in the mounting bracket.

3. Attach the mounting bracket to the wall, using screws and plugs appropriate for the wall

material.

4. Connect the network cable.

5. Optionally connect the I/O and audio cables; see page 17 for details.

6. Optionally insert the SD memory card.

7. Attach the camera unit to the mounting bracket using two appropriate screws.

Note:

• These instructions are for mounting the camera on a wall. The mounting bracket can also be used for

mounting the network camera to a junction box.

• AXIS P3353 and AXIS P3354 do not support audio and I/O.

Metal conduit (Optional/not included)

Mounting bracket (Optional/not included)

Network cable

M4x8 screw

Wall screws

Network cable

Page 8 AXIS P33 Network Camera Installation Guide

Assign an IP address

The network camera is designed for use on an Ethernet network and requires an IP address for

access. Most networks today have a DHCP server that automatically assigns IP addresses to

connected devices. If your network does not have a DHCP server, the network camera will use

192.168.0.90 as the default IP address.

AXIS IP Utility and AXIS Camera Management are the recommended methods for setting an IP

address in Windows. These free applications are available on the Axis Network Video Product CD

supplied with this product, or they can be downloaded from www.axis.com/techsup

Depending on the number of cameras you wish to install, use the method that suits you best.

Notes:

• If you are unable to set the IP address, check for any firewall blocking the operation.

• See page 15 for other available methods for setting or discovering the IP address of the network camera,

in relation to other operating systems.

Method Recommended for Operating system

AXIS IP Utility

See page 9

Single camera

Small installations

Windows

AXIS Camera Management

See page 10

Multiple cameras

Large installations

Installation on a different subnet

Windows 2000

Windows XP Pro

Windows 2003 Server

Windows 2008 Server

Windows Vista

Windows 7

AXIS P33 Network Camera Installation Guide Page 9

ENGLISH

AXIS IP Utility - single camera/ small installation

AXIS IP Utility automatically discovers and displays Axis devices on your network. You can also

manually set a static IP address through this application. AXIS IP Utility is available on the Axis

Network Video Product CD, or it can be downloaded from www.axis.com/techsup

Note that you must install the network camera on the same network segment (physical subnet) as

the computer running AXIS IP Utility.

Automatic discovery

1. Check that the network camera is connected to the network and that power has been applied.

2. Start AXIS IP Utility.

3. When the camera’s name appears in the window, double-click to open the camera’s home page.

4. See page 11 for instructions on how to set the password.

Set the IP address manually (optional)

1. Acquire an unused IP address on the same network segment your computer is connected to.

2. Select the network camera in the list.

3. Click the button Assign new IP address to selected device - and enter the serial number

and IP address for the network camera. The serial number is located on the product label.

4. Click the Assign button and follow on-screen instructions. Note that the camera must be

restarted within two minutes for the new IP address to be set.

5. Click the Home Page button to access the camera’s web pages.

6. See page 11 for instructions on how to set the password.

Page 10 AXIS P33 Network Camera Installation Guide

AXIS Camera Management - multiple cameras/large installations

AXIS Camera Management can automatically discover multiple Axis devices, show connection

status, manage firmware upgrades and set IP addresses.

Automatic discovery

1. Check that the camera is connected to the network and that power has been applied.

2. Start AXIS Camera Management. When the camera appears in the window, right-click the link

and select Live View Home Page.

3. See page 11 for instructions on how to set the password.

Assign an IP address in a single device

1. Select the camera in AXIS Camera Management and click the

Assign IP button .

2. Select Assign the following IP address and enter the IP

address, the subnet mask, and default router the device will

use.

3. Click OK.

Assign IP addresses in multiple devices

AXIS Camera Management speeds up the process of assigning IP

addresses to multiple devices, by suggesting IP addresses from a

specified range.

1. Select the devices you wish to configure (different models can be

selected) and click the Assign IP button .

2. Select Assign the following IP address range and enter the range

of IP addresses, the subnet mask, and default router the devices will use.

3. Click the OK button.

AXIS P33 Network Camera Installation Guide Page 11

ENGLISH

Set the password

To gain access to the product, the password for the default administrator user root must be set. This

is done in the Configure Root Password dialog, which is displayed when the network camera is

accessed for the first time.

To prevent network eavesdropping when setting the root password, this can be done via an

encrypted HTTPS connection, which requires an HTTPS certificate.

To set the password via a standard HTTP connection, enter it in the Configure Root Password

window. To set the password via an encrypted HTTPS connection, follow these steps:

1. Click the Create self-signed certificate button.

2. Provide the requested information and click OK. The certificate is created and the password can

now be set securely. All traffic to and from the network camera is encrypted from this point on.

3. Enter a password and then re-enter to confirm the spelling. Click OK. The password has now

been configured.

4. To log in, enter the user name “root” in the dialog as requested.

Note: The default administrator user name root cannot be deleted.

5. Enter the password as set above, and click OK. If the password is lost, the network camera must

be reset to the factory default settings. See page 19.

If required, click Yes to install AMC (AXIS Media Control), which allows viewing of the video stream

in Internet Explorer. You will need administrator rights on the computer to do this.

Note: To install AMC in Windows 7/Windows Vista, you must run Internet Explorer as administrator.

Right-click the Internet Explorer icon and select Run as administrator.

To configure the password directly via an

unencrypted connection, enter the

password here.

To create an HTTPS connection, start by

clicking this button.

Page 12 AXIS P33 Network Camera Installation Guide

6. Select the power line frequency (50 Hz or 60 Hz) used

in your location from the drop-down list the first time

network camera is accessed.

Note: Power line frequency can be changed from Plain Con-

fig or by resetting the product to factory default.

Selecting the wrong frequency will cause image flicker

if the product is used in fluorescent light environments. When using 50 Hz, the maximum frame

rate is limited to 25 fps.

Access the video stream

The Live View page of the network camera is displayed with links to the setup tools which allow

you to customize the camera.

If required, click Yes to install AMC (AXIS Media Control), which allows viewing of the video stream

in Internet Explorer. You will need administrator rights on the computer to do this.

Note: To install AMC in Windows 7/Windows Vista, you must run Internet Explorer as an administrator.

Right-click the Internet Explorer icon and select Run as administrator.

AXIS P33 Network Camera Installation Guide Page 13

ENGLISH

Adjust the Lens

Open the Live View page in the web interface and make the following adjustments to the camera:

1. Loosen the locking screw.

2. Turn the lens holder to the desired position.

3. Turn the lens to ensure the (horizontal) lines on either side of the lens are aligned horizontally.

Note: Ensure that the mark on the lens cover, between the horizontal lines, is facing up.

4. Once satisfied, gently tighten the locking screw to secure the camera’s position.

5. Open the Focus Adjustment page in the Web interface under Setup > Basic Setup > Focus &

Zoom, and follow the on-screen instructions. Use the image window to adjust the zoom and

focus. See the online help files for more information.

Note:

• Due to the dome’s refraction, the image may appear slightly out of focus once the dome has been placed.

To correct this go to the Focus Adjustment page in the Web interface under Setup > Basic Setup >

Focus & Zoom, and adjust the focus again.

Warning! Adjusting the focus and zoom manually can damage the lens.

Locking screw

Lens holder

Lens

Horizontal line

Mark

Page 14 AXIS P33 Network Camera Installation Guide

Complete the installation

1. If the cables are routed along the wall, remove the side lid from the camera’s dome cover.

2. Rotate the black protective shield inside the dome casing to match the camera’s position.

3. Clean the dome with a dry soft cloth to remove dust and finger prints and use a blower to

remove dust from the lens.

4. Mount the dome casing using the supplied tamper-proof screws and screw driver. Now that the

dome is in place, check that the camera is properly focused.

The installation is now complete.

Side lid Dome cover

Camera unit

Network cable

Dome cover

AXIS P33 Network Camera Installation Guide Page 15

ENGLISH

Other methods of setting the IP address

The table below shows the other methods available for setting or discovering the IP address. All

methods are enabled by default, and all can be disabled.

AXIS Video Hosting System (AVHS)

The camera can also be connected to an AVHS service for hosted video. If you have subscribed to an

AVHS service, follow the instructions in the Service Provider’s Installation Guide. For more

information and help to find a local AVHS Service Provider, go to www.axis.com/hosting

The camera owner authentication key is supplied with this product. The key is associated with the

camera’s unique serial number (S/N) as shown on the top of the label.

Note: Save the key for future reference.

Use in operating

system

Notes

UPnP™

Windows When enabled on your computer, the camera is automatically

detected and added to “My Network Places.”

Bonjour MAC OSX

(10.4 or later)

Applicable to browsers with support for Bonjour. Navigate to the

Bonjour bookmark in your browser (e.g. Safari) and click on the

link to access the camera’s web pages.

AXIS Dynamic DNS

Service

All A free service from Axis that allows you to quickly and simply

install your camera. Requires an Internet connection with no

HTTP proxy. See www.axiscam.net for more information.

ARP/Ping All See below. The command must be issued within 2 minutes of

connecting power to the camera.

View DHCP server

admin pages

All To view the admin pages for the network DHCP server, see the

server’s own documentation.

Page 16 AXIS P33 Network Camera Installation Guide

Set the IP address with ARP/Ping

1. Acquire a free static IP address on the same network segment your computer is connected to.

2. Locate the serial number (S/N) on the camera’s label.

3. Open a command prompt on your computer and enter the following commands:

4. Check that the network cable is connected to the network camera and then start/restart the

network camera, by disconnecting and reconnecting power. If PoE is used, start/restart the

network camera by disconnecting and then reconnecting the network cable.

5. Close the command prompt when you see ‘Reply from 192.168.0.125:...’ or similar.

6. In your browser, type in http://<IP address> in the Location/Address field and press Enter on

your keyboard.

Notes:

• To open a command prompt in Windows: from the Start menu, select Run... and type cmd. Click OK.

• To use the ARP command on a Mac OS X, use the Terminal utility in Application > Utilities.

Windows syntax Windows example

arp -s <IP Address> <Serial Number>

ping -l 408 -t <IP Address>

arp -s 192.168.0.125 00-40-8c-18-10-00

ping -l 408 -t 192.168.0.125

UNIX/Linux/Mac syntax UNIX/Linux/Mac example

arp -s <IP Address> <Serial Number> temp

ping -s 408 <IP Address>

arp -s 192.168.0.125 00:40:8c:18:10:00 temp

ping -s 408 192.168.0.125

AXIS P33 Network Camera Installation Guide Page 17

ENGLISH

Unit connectors

Note: AXIS P3353 and AXIS P3354 do not support audio or I/O.

Network connector - RJ-45 Ethernet connector. Supports Power over Ethernet.

Due to local regulations or environmental and electrical conditions in which the product is to be

used, a shielded network cable (STP) may be appropriate or required. Network cables that are

routed in outdoor environments or similar shall be shielded (STP) and intended for their specific

use. Make sure that the network switch is properly grounded. See Electromagnetic Compatibility

(EMC) for regulatory requirements.

Audio in - 3.5mm input for a mono microphone, or a line-in mono signal (left channel is used from

a stereo signal).

Audio out - Audio output (line level) that can be connected to a public address (PA) system or an

active speaker with a built-in amplifier. A pair of headphones can also be attached. A stereo

connector must be used for the audio out.

SDHC memory card slot - The SD memory card can be used for local recording with removable

storage.

I/O terminal connector - Used in applications for e.g. motion detection,

event triggering, time lapse recording and alarm notifications. In addition to

an auxiliary power and a GND pin, it provides the interface to:

• 1 transistor output - For connecting external devices such as

relays and LEDs. Connected devices can be activated by the

VAPIX® Application Programming Interface (API), by the output buttons on the Live

View page or by an Action Rule. The output will show as active (shown under System

Options > Ports & Devices) if the alarm device is activated.

• 1 digital input - An alarm input for connecting devices that can toggle between an

open and closed circuit, for example: PIRs, door/window contacts, and glass break

detectors. When a signal is received the state changes and the input becomes active

(shown under System Options > Ports & Devices).

Function Pin Notes Specifications

GND 1 Ground

3.3V DC

Power

2 Can be used to power auxiliary equipment.

Note: This pin can only be used as power out.

Max. load = 50mA

Digital

Input

3 Connect to GND to activate, or leave floating (or

unconnected) to deactivate.

Min. input= 0 to - 40V DC

Max. input= 0 to + 40V DC

Digital

Output

4 Uses an open-drain NFET transistor with the

source connected to GND. If used with an

external relay, a diode must be connected in

parallel with the load, for protection against

voltage transients.

Max. load = 100mA

Max voltage = + 40V DC

Pin1

Pin2

Pin3

Pin4

Page 18 AXIS P33 Network Camera Installation Guide

LED indicators

LED Color Indication

Network Green Steady for connection to a 100 Mbit/s network. Flashes for network activity.

Amber Steady for connection to 10 Mbit/s network. Flashes for network activity.

Unlit No network connection.

Status Green Steady green for normal operation.

Amber Steady during startup, during reset to factory default or when restoring settings.

Red Slow flash for failed upgrade.

Power Green Normal operation.

Amber Flashes green/amber during firmware upgrade.

AXIS P33 Network Camera Installation Guide Page 19

ENGLISH

Resetting to the Factory Default Settings

This will reset all parameters, including the IP address, to the factory default settings:

1. Disconnect power from the camera.

2. Press and hold the Control button and reconnect power (see Hardware overview, on page).

3. Keep the Control button pressed for about 15 seconds until the Status indicator flashes amber.

4. Release the Control button. The process is complete after about 1 minute (when the Status

indicator turns green). The network camera has been reset to the factory default settings. The

default IP address is 192.168.0.90

5. Re-assign the IP address.

6. Refocus the camera.

It is also possible to reset parameters to factory default via the web interface. Go to Setup > System

Options > Maintenance.

Accessing the camera from the Internet

Once installed, your network camera is accessible on your local network (LAN). To access the

camera from the Internet, network routers must be configured to allow incoming traffic, which is

usually done on a specific port

• HTTP port (default port 80) for viewing and configuration

• RTSP port (default port 554) for viewing H.264 video streams

Please refer to the documentation for your router for further instructions. For more information on

this and other topics, visit the Axis Support Web at www.axis.com/techsup

Further information

The user manual is available from the Axis Web site at www.axis.com.

To learn more about Axis' products and technologies, visit www.axis.com/academy, global learning

center for network video.

Tip!

Visit www.axis.com/techsup to check if there is updated firmware available for your Axis product.

To see the currently installed firmware version, see Setup > About in your web interface.

Mesures de sécurité

Lisez attentivement ce guide d’installation avant d’installer le produit. Conservez le guide d’installation pour une

utilisation ultérieure.

ATTENTION!

• Pour éviter d’endommager le produit Axis, utilisez l’emballage d’origine ou un emballage équivalent pour le

transporter.

• Conservez le produit Axis dans un environnement sec et aéré.

• Évitez d’exposer le produit Axis à des vibrations, des chocs ou une trop forte pression et ne l’installez pas

sur des supports instables, ou encore sur des surfaces ou des murs instables ou vibrants; cela risquerait de

l’endommager.

• Utilisez uniquement des outils à main pour l’installation du produit Axis: l’utilisation d’outils électriques ou

l’usage excessif de la force risquent de l’endommager.

• N’utilisez ni produits chimiques, ni substances caustiques, ni nettoyeurs aérosol. Utilisez un chiffon humide

pour le nettoyage.

• N’utilisez que des accessoires conformes aux caractéristiques techniques du produit. Ceux-ci peuvent être

fournis par Axis ou un fournisseur tiers.

• Utilisez uniquement des pièces de rechange fournies ou recommandées par Axis.

• Ne tentez pas de réparer le produit vous-même, contactez Axis ou votre revendeur Axis pour tout problème

de maintenance.

IMPORTANT!

• Ce produit Axis doit être utilisé conformément aux lois et réglementations locales en vigueur.

• Pour pouvoir être utilisé à l’extérieur, ce produit Axis doit être placé dans un boîtier d’extérieur homologué.

Remplacement des piles

Ce produit Axis nécessite une pile au lithium CR2032 de 3V pour l’alimentation de son horloge en temps réel

interne. Dans des conditions normales d’utilisation, cette pile est censée durer au moins 5ans. Si la pile est

faible, le fonctionnement de l’horloge en temps réel peut être affecté et entraîner sa réinitialisation à chaque

mise sous tension. Un message enregistré apparaît lorsque la pile doit être remplacée. Ne remplacez la pile que

lorsque cela est nécessaire.

Si la pile doit être remplacée, veuillez contacter www.axis.com/techsup pour obtenir de l’aide.

• Le remplacement incorrect de la pile peut entraîner un risque d’explosion.

• Remplacez la pile par une pile identique ou équivalente uniquement, en respectant les recommandations du

fabricant.

• Jetez les piles usagées conformément aux consignes du fabricant.

Nettoyage de la bulle du dôme

• Veillez à ne pas rayer ou endommager la bulle du dôme. Ne nettoyez pas la bulle du dôme si elle semble

propre à l’œil nu et ne frottez jamais sa surface. Un nettoyage excessif peut l’endommager.

• Pour le nettoyage général de la bulle du dôme, il est recommandé d’utiliser un savon ou un détergent

neutre sans solvant, non abrasif, avec de l’eau et un chiffon doux. Rincez abondamment avec de l’eau douce

et tiède. Séchez à l’aide d’un chiffon doux pour éviter les salissures d’eau.

• N’utilisez jamais de détergents forts, d’essence, de benzène ou d’acétone, etc. et évitez toute exposition

directe aux rayons du soleil ou à des températures élevées lors du nettoyage.

La page charge ...

Axis P3354-V Guide d'installation

Ce manuel convient également à

Axis P3354-V Guide d'installation

dans d''autres langues

Documents connexes

Autres documents