Sonoff SNZB-02D LCD Smart Temperature and Humidity Sensor Manuel utilisateur

Marque: Sonoff

Modèle: SNZB-02D LCD Smart Temperature and Humidity Sensor

Taper: Manuel utilisateur

·中文 ----------1 - 5 · English ----------6 - 10 · Warning ----------11 - 12

SNZB-02D

Zigbee LCD Smart

Temperature Humidity Sensor

功能特点

产品介绍

支架

电池电量

显示屏

信号图标

一款带LCD屏，兼具设备端查看实时温湿度及APP监控的智能温湿度传感器。超高精确度获取最

准确的温湿度数据，支持℃和℉单位切换、历史数据存储及导出，还有远程告警通知、语音询问、

场景联动实现你的家庭自动化。

APP监控

语音询问

高精度 ℃ /℉单位切换

℃℉

数据存储&导出告警通知

按键底座

配对至SONOFF Zigbee网关

1. 下载易微联App

请前往应用商店、Google Play Store或Apple App Store搜索"易微联"进行下载。

2. 设备通电

拔出电池绝缘片完成设备通电。

3. 添加 SONOFF Zigbee网关

如设备为不带电池版本，请安装电池（CR2450）给设备通电。

设备配对时效为30秒，添加成功后Zigbee信号图标为常亮状态。如添加失败，请将设备移近网关后

再重新添加。

在eWeLink App Zigbee网关主界面，点击 "添加" 子设备，然后长按设备按钮5秒直至设备

Zigbee信号图标呈闪烁状态，此时设备进入Zigbee设备配对状态，等待添加。

有效距离验证

4. 将设备添加至Zigbee网关

在选定的设备安装位置，短按设备的配对按键，设备屏幕上的信号图标保持常亮，表明该设

备和Zigbee网络下的设备（路由设备或网关）处于有效通讯距离。

已添加设备：0

暂无子设备，请添加

添加

产品参数

产品型号

供电

电池型号

无线连接

工作温度

工作湿度

LCD屏幕规格

外壳材料

产品规格

SNZB-02D

3V纽扣电池 x1

CR2450

Zigbee 3.0

-5℃~40℃

5%-95% RH，无冷凝

2.8"

PC+LCD

59.5x62.5x18.5mm

默认舒适度

干燥

潮湿

寒冷

炎热

湿度≤40%RH

湿度≥60%RH

温度≤19℃/66.2℉

温度≥27℃/80.6℉

按键动作说明

动作

双击

长按5秒

说明

温度单位切换℃/℉（出厂默认为℃）

恢复出厂设置，重新进入Zigbee配网状态

1. 桌面摆放

2. 配合底座安装

2-1. 底座磁吸到金属表面

2-2. 底座3M胶粘贴墙体

更换电池

设备安装

最大

3M 胶带

English

Features

Introduction

Stand

Battery

Display screen

Signal indicator

SNZB-02D is a smart temperature and humidity sensor with LCD screen, allows you to see

the real-time temperature and humidity on the screen and monitor the living conditions

on the App, provides accurate measurements with ultra-high precision, ability to switch

between ℃ and ℉, store and export historical data, get alerts and notiﬁcations, voice

commands, and set smart scenes to realize your home automation.

Voice Command

℃/℉ Reading Switch

℃℉

High Accuracy

Data Store & Export

APP Monitoring

Alert & Notiﬁcation

Button Base

English

Pair to SONOFF Zigbee Gateway

1. Download the eWeLink App

Please download the "eWeLink" App in Google Play Store or Apple App Store.

2. Power on

Pull out the battery insulation sheet to power the device on.

3. Pair SONOFF Zigbee gateway to your eWeLink account

If the device is the No battery version, please install the battery (CR2450) to power the

device on.

Place the device in your desired place and press the device's pairing button, then the

signal indicator on the screen keeps on, which means the device and the device

(router device or gateway) under the same Zigbee network is in the eﬀective communica-

tion distance.

The pairing time is 30s, when the device is added successfully, the Zigbee signal icon

will keep on. If the device is failed to be added, please move the device closer to the

Bridge and add it again.

English

4. Add the device to Zigbee Bridge

Tap "Add" on the main page of Zigbee Bridge on your eWeLink App, and long press the

button on the device for 5s until the Zigbee signal icon ﬂashes, now the device is

entered the pairing mode and waiting to be added.

Eﬀective Communication Distance Veriﬁcation

English

Speciﬁcations

Model

Power supply

Battery model

Wireless connection

Working temperature

Working humidity

LCD dimension

Casing material

Product dimension

SNZB-02D

3V button cell x 1

CR2450

Zigbee 3.0

-9.9℃~60℃

5%-95% RH, non-condensing

2.8"

PC+LCD

59.5x62.5x18.5mm

Default comfort level

Dry

Wet

Cold

Hot

Humidity ≤40%RH

Humidity ≥60%RH

Temperature ≤19℃/66.2℉

Temperature ≥27℃/80.6℉

Button action description

Action

Double-press

Long-press for 5s

Description

Switch unit readings (factory default is ℃)

Restore factory settings and enter Zigbee network

pairing mode again

English

2. Install with base

2-1. Attach to the metal surface with the magnetic base

2-2. Stick on the wall with 3M adhesive base

Battery replacement

1. Place on the desktop

Installation

Max

3M adhesive tape

Warning

FCC Warning

Changes or modiﬁcations not expressly approved by the party responsible for compliance

could avoid the user’s authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This transmitter must not be co-located or operating in conjunction with

any other antenna or transmitter.

Note:

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment oﬀ and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit diﬀerent from that to which the

receiver is connected.

— Consult the dealer or an experienced radio/TV technician for help.

“Do not ingest battery, Chemical Burn Hazard.”

This product contains a coin / button cellbattery. lf the coin / button cell battery is swallowed,

it can cause severeinternal burns in just 2 hours and can lead to death.

Keep new and used batteries away from children.lf the battery compartment does not close

securely, stop using the productand keep it away from children.

lf you think batteries might have been swallowed or placed inside any partof the body, seek

immediate medical attention.

IC Warning

This device complies with Innovation, Science and Economic Development Canada

licence-exempt RSS standard (s). Operation is subject to the following two conditions: (1)

this device may not cause interference, and (2) this device must accept any interference,

including interference that may cause undesired operation of the device.

Le onjunc areil est conforme aux CNR d’ l’innovation, la science et le développement

économique Canada licables aux areils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes:

(1) l’areil ne doit pas produire de brouillage, et

(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, onj si le

brouillage est susceptible d’en compromettre le fonctionnement.

Any changes or modiﬁcations not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

Tous les changements ou modiﬁcations non expressément approuvée par le responsible

de la conformité pourrait vider l’utilisateur est habilité à exploiter l’équipemen.

ISEDC Radiation Exposure Statement:

This equipment complies with ISEDC RF radiation exposure limits set forth for an

uncontrolled environment.

This transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

Cet appareil est

conforme aux limitesd’exposition de rayonnement RF ISEDC établiespour un environne-

ment non contrôlé.

Cetémetteur ne doit pas être co-implanté oufonctionner en onjunction avec toute

autreantenne ou transmetteur.

Warning

Hereby, Shenzhen Sonoﬀ Technologies Co., Ltd. declares that the radio equipment type

SNZB-02D is in compliance with Directive 2014/53/EU.The full text of the EU declaration of

conformity is available at the following internet address:

https://sonoﬀ.tech/usermanuals

Operation frequency Range: 2405-2480MHz(Zigbee), 2402-2480MHz(BLE)

RF Output Power: 5dBm(Zigbee), 5.5dBm(BLE)

Sonoff SNZB-02D LCD Smart Temperature and Humidity Sensor Manuel utilisateur

Marque: Sonoff

Modèle: SNZB-02D LCD Smart Temperature and Humidity Sensor

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Sonoff SNZB-02D LCD Smart Temperature and Humidity Sensor User manual

Sonoff SNZB-02D LCD Smart Temperature and Humidity Sensor Manuel utilisateur

Sonoff SNZB-02D LCD Smart Temperature and Humidity Sensor Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents