Firepower Plasma Cutting Power Supply PC-500 Manuel utilisateur

Marque: Firepower

Modèle: Plasma Cutting Power Supply PC-500

Catégorie: Système de soudage

Taper: Manuel utilisateur

Ce manuel convient également à

Plasma Cutting Power Supply Firepower PC-500

Operating Manual

Plasma Cutting

Power Supply

Firepower PC-500

June 23, 2004 Manual No. 0-4601

A-03688

Plasma Cutting Power Supply

Model PC-500

Operating Manual Number 0-4601

www.firepoweronline.com

Published by:

Thermal Dynamics Corporation

82 Benning Street

West Lebanon, New Hampshire, USA 03784

(603) 298-5711

Thermal Dynamics Corporation

Reproduction of this work, in whole or in part, without written per-

mission of the publisher is prohibited.

The publisher does not assume and hereby disclaims any liability to

any party for any loss or damage caused by any error or omission in

this Manual, whether such error results from negligence, accident, or

any other cause.

Printed in the United States of America

Publication Date: June 23, 2004

Record the following information for Warranty purposes:

Where Purchased:____________________________________

Purchase Date:_______________________________________

Power Supply Serial #:________________________________

Torch Serial #:________________________________________

WARNINGS

Read and understand this entire Manual and your employer’s safety practices before installing, oper-

ating, or servicing the equipment.

While the information contained in this Manual represents the Manufacturer's best judgement, the

Manufacturer assumes no liability for its use.

TABLE OF CONTENTS

SECTION 1:

GENERAL INFORMATION ................................................................................................ 1-1

1.01 Notes, Cautions and Warnings ...................................................................... 1-1

1.02 Important Safety Precautions ....................................................................... 1-1

1.03 Publications.................................................................................................. 1-2

1.04 Note, Attention et Avertissement .................................................................. 1-3

1.05 Precautions De Securite Importantes ........................................................... 1-3

1.06 Documents De Reference ............................................................................. 1-5

1.07 Declaration of Conformity ............................................................................. 1-7

1.08 Statement of Warranty .................................................................................. 1-8

SECTION 2:

INTRODUCTION ............................................................................................................... 2-1

2.01 Scope of Manual .......................................................................................... 2-1

2.02 Power Supply Specifications......................................................................... 2-1

2.03 Input Wiring Specifications ........................................................................... 2-2

2.04 Power Supply Features ................................................................................. 2-3

2.05 Power Supply Options .................................................................................. 2-4

SECTION 3: INSTALLATION..................................................................................................... 3-1

3.1 Unpacking .................................................................................................... 3-1

3.2 Lifting Options .............................................................................................. 3-1

3.3 Primary Input Power Connections ................................................................. 3-2

3.4 Gas Connections .......................................................................................... 3-3

3.5 Torch Connections ........................................................................................ 3-6

SECTION 4: OPERATION......................................................................................................... 4-1

4.01 Front Panel Controls and Indicators .............................................................. 4-1

4.02 Preparations for Operation ............................................................................ 4-2

TABLE OF CONTENTS (continued)

SECTION 5:

SERVICE .......................................................................................................................... 5-1

5.01 General Maintenance .................................................................................... 5-1

5.02 Common Faults ............................................................................................ 5-4

5.03 Basic Troubleshooting Guide ......................................................................... 5-5

5.04 Power Supply Basic Parts Replacement......................................................5-10

SECTION 6:

PARTS LISTS ................................................................................................................... 6-1

6.01 Introduction................................................................................................... 6-1

6.02 Ordering Information ..................................................................................... 6-1

6.03 Power Supply Replacement .......................................................................... 6-1

6.04 Replacement Parts ....................................................................................... 6-2

6.05 Torch Parts ................................................................................................... 6-3

APPENDIX 1: SEQUENCE OF OPERATION (BLOCK DIAGRAM) .......................................... A-1

APPENDIX 2: DATA TAG INFORMATION .................................................................................. A-2

APPENDIX 3: MAINTENANCE SCHEDULE ............................................................................. A-3

APPENDIX 4: TORCH PIN - OUT DIAGRAM ............................................................................A-4

APPENDIX 5: TORCH CONNECTION DIAGRAM ..................................................................... A-5

APPENDIX 6: SYSTEM SCHEMATIC ...................................................................................... A-6

Date: January 27, 2004 1-1 GENERAL INFORMATION

SECTION 1:

GENERAL INFORMATION

1.01 Notes, Cautions and Warnings

Throughout this manual, notes, cautions, and warnings

are used to highlight important information. These high-

lights are categorized as follows:

NOTE

An operation, procedure, or background informa-

tion which requires additional emphasis or is help-

ful in efficient operation of the system.

CAUTION

A procedure which, if not properly followed, may

cause damage to the equipment.

WARNING

A procedure which, if not properly followed, may

cause injury to the operator or others in the oper-

ating area.

1.02 Important Safety Precautions

WARNINGS

OPERATION AND MAINTENANCE OF

PLASMA ARC EQUIPMENT CAN BE DAN-

GEROUS AND HAZARDOUS TO YOUR

HEALTH.

Plasma arc cutting produces intense electric and

magnetic emissions that may interfere with the

proper function of cardiac pacemakers, hearing

aids, or other electronic health equipment. Per-

sons who work near plasma arc cutting applica-

tions should consult their medical health profes-

sional and the manufacturer of the health

equipment to determine whether a hazard exists.

To prevent possible injury, read, understand and

follow all warnings, safety precautions and in-

structions before using the equipment. Call 1-603-

298-5711 or your local distributor if you have any

questions.

GASES AND FUMES

Gases and fumes produced during the plasma cutting

process can be dangerous and hazardous to your health.

• Keep all fumes and gases from the breathing area.

Keep your head out of the welding fume plume.

• Use an air-supplied respirator if ventilation is not

adequate to remove all fumes and gases.

• The kinds of fumes and gases from the plasma arc

depend on the kind of metal being used, coatings

on the metal, and the different processes. You must

be very careful when cutting or welding any met-

als which may contain one or more of the follow-

ing:

Antimony Chromium Mercury

Arsenic Cobalt Nickel

Barium Copper Selenium

Beryllium Lead Silver

Cadmium Manganese Vanadium

• Always read the Material Safety Data Sheets

(MSDS) that should be supplied with the material

you are using. These MSDSs will give you the in-

formation regarding the kind and amount of fumes

and gases that may be dangerous to your health.

• For information on how to test for fumes and gases

in your workplace, refer to item 1 in Subsection 1.03,

Publications in this manual.

• Use special equipment, such as water or down draft

cutting tables, to capture fumes and gases.

• Do not use the plasma torch in an area where com-

bustible or explosive gases or materials are located.

• Phosgene, a toxic gas, is generated from the vapors

of chlorinated solvents and cleansers. Remove all

sources of these vapors.

• This product, when used for welding or cutting,

produces fumes or gases which contain chemicals

known to the State of California to cause birth de-

fects and, in some cases, cancer. (California Health

& Safety Code Sec. 25249.5 et seq.)

ELECTRIC SHOCK

Electric Shock can injure or kill. The plasma arc process

uses and produces high voltage electrical energy. This

electric energy can cause severe or fatal shock to the op-

erator or others in the workplace.

• Never touch any parts that are electrically “live”

or “hot.”

GENERAL INFORMATION 1-2 Date: January 27, 2004

• Wear dry gloves and clothing. Insulate yourself

from the work piece or other parts of the welding

circuit.

• Repair or replace all worn or damaged parts.

• Extra care must be taken when the workplace is

moist or damp.

• Install and maintain equipment according to NEC

code, refer to item 9 in Subsection 1.03, Publica-

tions.

• Disconnect power source before performing any

service or repairs.

• Read and follow all the instructions in the Operat-

ing Manual.

FIRE AND EXPLOSION

Fire and explosion can be caused by hot slag, sparks, or

the plasma arc.

• Be sure there is no combustible or flammable ma-

terial in the workplace. Any material that cannot

be removed must be protected.

• Ventilate all flammable or explosive vapors from

the workplace.

• Do not cut or weld on containers that may have

held combustibles.

• Provide a fire watch when working in an area where

fire hazards may exist.

• Hydrogen gas may be formed and trapped under

aluminum workpieces when they are cut under-

water or while using a water table. DO NOT cut

aluminum alloys underwater or on a water table

unless the hydrogen gas can be eliminated or dis-

sipated. Trapped hydrogen gas that is ignited will

cause an explosion.

NOISE

Noise can cause permanent hearing loss. Plasma arc pro-

cesses can cause noise levels to exceed safe limits. You

must protect your ears from loud noise to prevent per-

manent loss of hearing.

• To protect your hearing from loud noise, wear pro-

tective ear plugs and/or ear muffs. Protect others

in the workplace.

• Noise levels should be measured to be sure the deci-

bels (sound) do not exceed safe levels.

• For information on how to test for noise, see item 1

in Subsection 1.03, Publications, in this manual.

PLASMA ARC RAYS

Plasma Arc Rays can injure your eyes and burn your skin.

The plasma arc process produces very bright ultra violet

and infra red light. These arc rays will damage your

eyes and burn your skin if you are not properly protected.

• To protect your eyes, always wear a welding hel-

met or shield. Also always wear safety glasses with

side shields, goggles or other protective eye wear.

• Wear welding gloves and suitable clothing to pro-

tect your skin from the arc rays and sparks.

• Keep helmet and safety glasses in good condition.

Replace lenses when cracked, chipped or dirty.

• Protect others in the work area from the arc rays.

Use protective booths, screens or shields.

• Use the shade of lens as suggested in the following

per ANSI/ASC Z49.1:

Minimum Protective Suggested

Arc Current Shade No. Shade No.

Less Than 300* 8 9

300 - 400* 9 12

400 - 800* 10 14

* These values apply where the actual arc is clearly

seen. Experience has shown that lighter filters

may be used when the arc is hidden by the work-

piece.

1.03 Publications

Refer to the following standards or their latest revisions

for more information:

1. OSHA, SAFETY AND HEALTH STANDARDS, 29CFR

1910, obtainable from the Superintendent of Docu-

ments, U.S. Government Printing Office, Washington,

D.C. 20402

2. ANSI Standard Z49.1, SAFETY IN WELDING AND

CUTTING, obtainable from the American Welding So-

ciety, 550 N.W. LeJeune Rd, Miami, FL 33126

3. NIOSH, SAFETY AND HEALTH IN ARC WELDING

AND GAS WELDING AND CUTTING, obtainable

from the Superintendent of Documents, U.S. Govern-

ment Printing Office, Washington, D.C. 20402

4. ANSI Standard Z87.1, SAFE PRACTICES FOR OCCU-

PATION AND EDUCATIONAL EYE AND FACE PRO-

TECTION, obtainable from American National Stan-

dards Institute, 1430 Broadway, New York, NY 10018

5. ANSI Standard Z41.1, STANDARD FOR MEN’S

SAFETY-TOE FOOTWEAR, obtainable from the Ameri-

can National Standards Institute, 1430 Broadway, New

York, NY 10018

Date: January 27, 2004 1-3 GENERAL INFORMATION

6. ANSI Standard Z49.2, FIRE PREVENTION IN THE USE

OF CUTTING AND WELDING PROCESSES, obtain-

able from American National Standards Institute, 1430

Broadway, New York, NY 10018

7. AWS Standard A6.0, WELDING AND CUTTING CON-

TAINERS WHICH HAVE HELD COMBUSTIBLES, ob-

tainable from American Welding Society, 550 N.W.

LeJeune Rd, Miami, FL 33126

8. NFPA Standard 51, OXYGEN-FUEL GAS SYSTEMS

FOR WELDING, CUTTING AND ALLIED PRO-

CESSES, obtainable from the National Fire Protection

Association, Batterymarch Park, Quincy, MA 02269

9. NFPA Standard 70, NATIONAL ELECTRICAL CODE,

obtainable from the National Fire Protection Associa-

tion, Batterymarch Park, Quincy, MA 02269

10. NFPA Standard 51B, CUTTING AND WELDING PRO-

CESSES, obtainable from the National Fire Protection

Association, Batterymarch Park, Quincy, MA 02269

11. CGA Pamphlet P-1, SAFE HANDLING OF COM-

PRESSED GASES IN CYLINDERS, obtainable from the

Compressed Gas Association, 1235 Jefferson Davis

Highway, Suite 501, Arlington, VA 22202

12. CSA Standard W117.2, CODE FOR SAFETY IN WELD-

ING AND CUTTING, obtainable from the Canadian

Standards Association, Standards Sales, 178 Rexdale

Boulevard, Rexdale, Ontario, Canada M9W 1R3

13. NWSA booklet, WELDING SAFETY BIBLIOGRAPHY

obtainable from the National Welding Supply Associa-

tion, 1900 Arch Street, Philadelphia, PA 19103

14. American Welding Society Standard AWSF4.1, RECOM-

MENDED SAFE PRACTICES FOR THE PREPARA-

TION FOR WELDING AND CUTTING OF CONTAIN-

ERS AND PIPING THAT HAVE HELD HAZARDOUS

SUBSTANCES, obtainable from the American Welding

Society, 550 N.W. LeJeune Rd, Miami, FL 33126

15. ANSI Standard Z88.2, PRACTICE FOR RESPIRATORY

PROTECTION, obtainable from American National

Standards Institute, 1430 Broadway, New York, NY

10018

1.04 Note, Attention et

Avertissement

Dans ce manuel, les mots “note,” “attention,” et

“avertissement” sont utilisés pour mettre en relief des

informations à caractère important. Ces mises en relief

sont classifiées comme suit :

NOTE

Toute opération, procédure ou renseignement

général sur lequel il importe d’insister davantage

ou qui contribue à l’efficacité de fonctionnement

du système.

ATTENTION

Toute procédure pouvant résulter

l’endommagement du matériel en cas de non-

respect de la procédure en question.

AVERTISSEMENT

Toute procédure pouvant provoquer des blessures

de l’opérateur ou des autres personnes se trouvant

dans la zone de travail en cas de non-respect de la

procédure en question.

1.05 Precautions De Securite

Importantes

AVERTISSEMENTS

L’OPÉRATION ET LA MAINTENANCE DU

MATÉRIEL DE SOUDAGE À L’ARC AU JET

DE PLASMA PEUVENT PRÉSENTER DES

RISQUES ET DES DANGERS DE SANTÉ.

Coupant à l’arc au jet de plasma produit de l’énergie

électrique haute tension et des émissions

magnétique qui peuvent interférer la fonction

propre d’un “pacemaker” cardiaque, les appareils

auditif, ou autre matériel de santé electronique.

Ceux qui travail près d’une application à l’arc au

jet de plasma devrait consulter leur membre

professionel de médication et le manufacturier de

matériel de santé pour déterminer s’il existe des

risques de santé.

Il faut communiquer aux opérateurs et au person-

nel TOUS les dangers possibles. Afin d’éviter les

blessures possibles, lisez, comprenez et suivez tous

les avertissements, toutes les précautions de sécurité

et toutes les consignes avant d’utiliser le matériel.

Composez le + 603-298-5711 ou votre distributeur

local si vous avez des questions.

FUMÉE et GAZ

La fumée et les gaz produits par le procédé de jet de

plasma peuvent présenter des risques et des dangers de

santé.

GENERAL INFORMATION 1-4 Date: January 27, 2004

• Eloignez toute fumée et gaz de votre zone de respira-

tion. Gardez votre tête hors de la plume de fumée

provenant du chalumeau.

• Utilisez un appareil respiratoire à alimentation en air

si l’aération fournie ne permet pas d’éliminer la fumée

et les gaz.

• Les sortes de gaz et de fumée provenant de l’arc de

plasma dépendent du genre de métal utilisé, des

revêtements se trouvant sur le métal et des différents

procédés. Vous devez prendre soin lorsque vous

coupez ou soudez tout métal pouvant contenir un ou

plusieurs des éléments suivants:

antimoine cadmium mercure

argent chrome nickel

arsenic cobalt plomb

baryum cuivre sélénium

béryllium manganèse vanadium

• Lisez toujours les fiches de données sur la sécurité

des matières (sigle américain “MSDS”); celles-ci

devraient être fournies avec le matériel que vous

utilisez. Les MSDS contiennent des renseignements

quant à la quantité et la nature de la fumée et des gaz

pouvant poser des dangers de santé.

• Pour des informations sur la manière de tester la

fumée et les gaz de votre lieu de travail, consultez

l’article 1 et les documents cités à la page 5.

• Utilisez un équipement spécial tel que des tables de

coupe à débit d’eau ou à courant descendant pour

capter la fumée et les gaz.

• N’utilisez pas le chalumeau au jet de plasma dans une

zone où se trouvent des matières ou des gaz combus-

tibles ou explosifs.

• Le phosgène, un gaz toxique, est généré par la fumée

provenant des solvants et des produits de nettoyage

chlorés. Eliminez toute source de telle fumée.

• Ce produit, dans le procéder de soudage et de coupe,

produit de la fumée ou des gaz pouvant contenir des

éléments reconnu dans L’état de la Californie, qui

peuvent causer des défauts de naissance et le cancer.

(La sécurité de santé en Californie et la code sécurité

Sec. 25249.5 et seq.)

CHOC ELECTRIQUE

Les chocs électriques peuvent blesser ou même tuer. Le

procédé au jet de plasma requiert et produit de l’énergie

électrique haute tension. Cette énergie électrique peut

produire des chocs graves, voire mortels, pour l’opérateur

et les autres personnes sur le lieu de travail.

• Ne touchez jamais une pièce “sous tension” ou “vive”;

portez des gants et des vêtements secs. Isolez-vous

de la pièce de travail ou des autres parties du circuit

de soudage.

• Réparez ou remplacez toute pièce usée ou

endommagée.

• Prenez des soins particuliers lorsque la zone de tra-

vail est humide ou moite.

• Montez et maintenez le matériel conformément au

Code électrique national des Etats-Unis. (Voir la page

5, article 9.)

• Débranchez l’alimentation électrique avant tout tra-

vail d’entretien ou de réparation.

• Lisez et respectez toutes les consignes du Manuel de

consignes.

INCENDIE ET EXPLOSION

Les incendies et les explosions peuvent résulter des scories

chaudes, des étincelles ou de l’arc de plasma. Le procédé

à l’arc de plasma produit du métal, des étincelles, des

scories chaudes pouvant mettre le feu aux matières com-

bustibles ou provoquer l’explosion de fumées

inflammables.

• Soyez certain qu’aucune matière combustible ou in-

flammable ne se trouve sur le lieu de travail. Protégez

toute telle matière qu’il est impossible de retirer de la

zone de travail.

• Procurez une bonne aération de toutes les fumées

inflammables ou explosives.

• Ne coupez pas et ne soudez pas les conteneurs ayant

pu renfermer des matières combustibles.

• Prévoyez une veille d’incendie lors de tout travail dans

une zone présentant des dangers d’incendie.

• Le gas hydrogène peut se former ou s’accumuler sous

les pièces de travail en aluminium lorsqu’elles sont

coupées sous l’eau ou sur une table d’eau. NE PAS

couper les alliages en aluminium sous l’eau ou sur

une table d’eau à moins que le gas hydrogène peut

s’échapper ou se dissiper. Le gas hydrogène accumulé

explosera si enflammé.

RAYONS D’ARC DE PLASMA

Les rayons provenant de l’arc de plasma peuvent blesser

vos yeux et brûler votre peau. Le procédé à l’arc de

plasma produit une lumière infra-rouge et des rayons

Date: January 27, 2004 1-5 GENERAL INFORMATION

ultra-violets très forts. Ces rayons d’arc nuiront à vos

yeux et brûleront votre peau si vous ne vous protégez

pas correctement.

• Pour protéger vos yeux, portez toujours un casque ou

un écran de soudeur. Portez toujours des lunettes de

sécurité munies de parois latérales ou des lunettes de

protection ou une autre sorte de protection oculaire.

• Portez des gants de soudeur et un vêtement protecteur

approprié pour protéger votre peau contre les

étincelles et les rayons de l’arc.

• Maintenez votre casque et vos lunettes de protection

en bon état. Remplacez toute lentille sale ou

comportant fissure ou rognure.

• Protégez les autres personnes se trouvant sur la zone

de travail contre les rayons de l’arc en fournissant des

cabines ou des écrans de protection.

• Utilisez la nuance de lentille qui est suggèrée dans le

recommendation qui suivent ANSI/ASC Z49.1:

Nuance Minimum Nuance Suggerée

Courant Arc Protective Numéro Numéro

Moins de 300* 8 9

300 - 400* 9 12

400 - 800* 10 14

* Ces valeurs s’appliquent ou l’arc actuel est observé

clairement. L’experience a démontrer que les filtres

moins foncés peuvent être utilisés quand l’arc est

caché par moiceau de travail.

BRUIT

Le bruit peut provoquer une perte permanente de l’ouïe.

Les procédés de soudage à l’arc de plasma peuvent

provoquer des niveaux sonores supérieurs aux limites

normalement acceptables. Vous dú4ez vous protéger les

oreilles contre les bruits forts afin d’éviter une perte

permanente de l’ouïe.

• Pour protéger votre ouïe contre les bruits forts, portez

des tampons protecteurs et/ou des protections

auriculaires. Protégez également les autres personnes

se trouvant sur le lieu de travail.

• Il faut mesurer les niveaux sonores afin d’assurer que

les décibels (le bruit) ne dépassent pas les niveaux

sûrs.

• Pour des renseignements sur la manière de tester le

bruit, consultez l’article 1, page 5.

1.06 Documents De Reference

Consultez les normes suivantes ou les révisions les plus

récentes ayant été faites à celles-ci pour de plus amples

renseignements :

1. OSHA, NORMES DE SÉCURITÉ DU TRAVAIL ET DE

PROTECTION DE LA SANTÉ, 29CFR 1910,

disponible auprès du Superintendent of Documents,

U.S. Government Printing Office, Washington, D.C.

20402

2. Norme ANSI Z49.1, LA SÉCURITÉ DES

OPÉRATIONS DE COUPE ET DE SOUDAGE,

disponible auprès de la Société Américaine de

Soudage (American Welding Society), 550 N.W.

LeJeune Rd., Miami, FL 33126

3. NIOSH, LA SÉCURITÉ ET LA SANTÉ LORS DES

OPÉRATIONS DE COUPE ET DE SOUDAGE À

L’ARC ET AU GAZ, disponible auprès du Superin-

tendent of Documents, U.S. Government Printing

Office, Washington, D.C. 20402

4. Norme ANSI Z87.1, PRATIQUES SURES POUR LA

PROTECTION DES YEUX ET DU VISAGE AU TRA-

VAIL ET DANS LES ECOLES, disponible de l’Institut

Américain des Normes Nationales (American Na-

tional Standards Institute), 1430 Broadway, New York,

NY 10018

5. Norme ANSI Z41.1, NORMES POUR LES

CHAUSSURES PROTECTRICES, disponible auprès

de l’American National Standards Institute, 1430

Broadway, New York, NY 10018

6. Norme ANSI Z49.2, PRÉVENTION DES INCENDIES

LORS DE L’EMPLOI DE PROCÉDÉS DE COUPE ET

DE SOUDAGE, disponible auprès de l’American Na-

tional Standards Institute, 1430 Broadway, New York,

NY 10018

7. Norme A6.0 de l’Association Américaine du Soudage

(AWS), LE SOUDAGE ET LA COUPE DE

CONTENEURS AYANT RENFERMÉ DES PRODUITS

COMBUSTIBLES, disponible auprès de la American

Welding Society, 550 N.W. LeJeune Rd., Miami, FL

33126

8. Norme 51 de l’Association Américaine pour la Pro-

tection contre les Incendies (NFPA), LES SYSTEMES

À GAZ AVEC ALIMENTATION EN OXYGENE

POUR LE SOUDAGE, LA COUPE ET LES

PROCÉDÉS ASSOCIÉS, disponible auprès de la Na-

tional Fire Protection Association, Batterymarch Park,

Quincy, MA 02269

GENERAL INFORMATION 1-6 Date: January 27, 2004

9. Norme 70 de la NFPA, CODE ELECTRIQUE NA-

TIONAL, disponible auprès de la National Fire Pro-

tection Association, Batterymarch Park, Quincy, MA

02269

10. Norme 51B de la NFPA, LES PROCÉDÉS DE

COUPE ET DE SOUDAGE, disponible auprès de la

National Fire Protection Association, Batterymarch

Park, Quincy, MA 02269

11. Brochure GCA P-1, LA MANIPULATION SANS

RISQUE DES GAZ COMPRIMÉS EN CYLINDRES,

disponible auprès de l’Association des Gaz

Comprimés (Compressed Gas Association), 1235

Jefferson Davis Highway, Suite 501, Arlington, VA

22202

12. Norme CSA W117.2, CODE DE SÉCURITÉ POUR

LE SOUDAGE ET LA COUPE, disponible auprès

de l’Association des Normes Canadiennes, Stan-

dards Sales, 178 Rexdale Boulevard, Rexdale,

Ontario, Canada, M9W 1R3

13. Livret NWSA, BIBLIOGRAPHIE SUR LA

SÉCURITÉ DU SOUDAGE, disponible auprès de

l’Association Nationale de Fournitures de Soudage

(National Welding Supply Association), 1900 Arch

Street, Philadelphia, PA 19103

14. Norme AWSF4.1 de l’Association Américaine de

Soudage, RECOMMANDATIONS DE PRATIQUES

SURES POUR LA PRÉPARATION À LA COUPE ET

AU SOUDAGE DE CONTENEURS ET TUYAUX

AYANT RENFERMÉ DES PRODUITS

DANGEREUX , disponible auprès de la American

Welding Society, 550 N.W. LeJeune Rd., Miami, FL

33126

15. Norme ANSI Z88.2, PRATIQUES DE PROTECTION

RESPIRATOIRE, disponible auprès de l’American

National Standards Institute, 1430 Broadway, New

York, NY 10018

Date: January 27, 2004 1-7 GENERAL INFORMATION

1.07 Declaration of Conformity

Manufacturer: Thermal Dynamics Corporation

Address: 82 Benning Street

West Lebanon, New Hampshire 03784

USA

The equipment described in this manual conforms to all applicable aspects and regulations of the ‘Low Voltage Directive’

(European Council Directive 73/23/EEC as amended by Council Directive 93/68/EEC) and to the National legislation for

the enforcement of this Directive.

The equipment described in this manual conforms to all applicable aspects and regulations of the "EMC Directive" (Euro-

pean Council Directive 89/336/EEC) and to the National legislation for the enforcement of this Directive.

Serial numbers are unique with each individual piece of equipment and details description, parts used to manufacture a unit

and date of manufacture.

National Standard and Technical Specifications

The product is designed and manufactured to a number of standards and technical requirements. Among them are:

* CSA (Canadian Standards Association) standard C22.2 number 60 for Arc welding equipment.

* UL (Underwriters Laboratory) rating 94VO flammability testing for all printed-circuit boards used.

* ISO/IEC 60974-1 (BS 638-PT10) (EN 60 974-1) (EN50192) (EN50078) applicable to plasma cutting equipment and

associated accessories.

* Extensive product design verification is conducted at the manufacturing facility as part of the routine design and

manufacturing process. This is to ensure the product is safe, when used according to instructions in this manual and

related industry standards, and performs as specified. Rigorous testing is incorporated into the manufacturing

process to ensure the manufactured product meets or exceeds all design specifications.

Thermal Dynamics has been manufacturing products for more than 30 years, and will continue to achieve excellence in our

area of manufacture.

Manufacturers responsible representative: Steve Ward

Operations Director

Thermadyne Europe

Europa Building

Chorley N Industrial Park

Chorley, Lancashire,

England PR6 7BX

GENERAL INFORMATION 1-8 Date: January 27, 2004

1.08 Statement of Warranty

LIMITED WARRANTY: Thermal Dynamics

Corporation (hereinafter “Thermal”) warrants that its products will be free of defects in

workmanship or material. Should any failure to conform to this warranty appear within the time period applicable to the Thermal

products as stated below, Thermal shall, upon notification thereof and substantiation that the product has been stored, installed, operated,

and maintained in accordance with Thermal’s specifications, instructions, recommendations and recognized standard industry practice,

and not subject to misuse, repair, neglect, alteration, or accident, correct such defects by suitable repair or replacement, at Thermal’s sole

option, of any components or parts of the product determined by Thermal to be defective.

THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE.

LIMITATION OF LIABILITY: Thermal shall not under any circumstances be liable for special or consequential damages, such as, but not

limited to, damage or loss of purchased or replacement goods, or claims of customers of distributor (hereinafter “Purchaser”) for service

interruption. The remedies of the Purchaser set forth herein are exclusive and the liability of Thermal with respect to any contract, or

anything done in connection therewith such as the performance or breach thereof, or from the manufacture, sale, delivery, resale, or use of

any goods covered by or furnished by Thermal whether arising out of contract, negligence, strict tort, or under any warranty, or otherwise,

shall not, except as expressly provided herein, exceed the price of the goods upon which such liability is based.

THIS WARRANTY BECOMES INVALID IF REPLACEMENT PARTS OR ACCESSORIES ARE USED WHICH MAY IMPAIR THE

SAFETY OR PERFORMANCE OF ANY THERMAL PRODUCT.

THIS WARRANTY IS INVALID IF THE PRODUCT IS SOLD BY NON-AUTHORIZED PERSONS.

The limited warranty periods for Thermal products shall be as follows (with the exception of XL Plus Series, CutMaster Series , Cougar

and DRAG-GUN): A maximum of three (3) years from date of sale to an authorized distributor and a maximum of two (2) years from

date of sale by such distributor to the Purchaser, and with the further limitations on such two (2) year period (see chart below).

The limited warranty period for XL Plus Series and CutMaster Series shall be as follows: A maximum of four (4) years from date

of sale to an authorized distributor and a maximum of three (3) years from date of sale by such distributor to the Purchaser, and

with the further limitations on such three (3) year period (see chart below).

The limited warranty period for Cougar and DRAG-GUN shall be as follows: A maximum of two (2) years from date of sale to an

authorized distributor and a maximum of one (1) year from date of sale by such distributor to the Purchaser, and with the further

limitations on such two (2) year period (see chart below).

Parts

XL Plus & Parts Parts

PAK Units, Power Supplies CutMaster Series Cougar/Drag-Gun All Others Labor

Main Power Magnetics 3 Years 1 Year 2 Years 1 Year

Original Main Power Rectifier 3 Years 1 Year 2 Years 1 Year

Control PC Board 3 Years 1 Year 2 Years 1 Year

All Other Circuits And Components Including, 1 Year 1 Year 1 Year 1 Year

But Not Limited To, Starting Circuit,

Contactors, Relays, Solenoids, Pumps,

Power Switching Semi-Conductors

Consoles, Control Equipment, Heat 1 Year 1 Year 1 Year

Exchanges, And Accessory Equipment

Torch And Leads

Maximizer 300 Torch 1 Year 1 Year

SureLok Torches 1 Year 1 Year 1 Year

All Other Torches 180 Days 180 Days 180 Days 180 Days

Repair/Replacement Parts 90 Days 90 Days 90 Days None

Warranty repairs or replacement claims under this limited warranty must be submitted by an authorized Thermal Dynamics® repair

facility within thirty (30) days of the repair. No transportation costs of any kind will be paid under this warranty. Transportation charges

to send products to an authorized warranty repair facility shall be the responsibility of the customer. All returned goods shall be at the

customer’s risk and expense. This warranty supersedes all previous Thermal warranties.

Effective: November 15, 2001

Manual 0-4601 2-1 INTRODUCTION

SECTION 2:

INTRODUCTION

2.01 Scope of Manual

This manual contains descriptions, operating instructions and basic maintenance procedures for the Firepower Model

PC-500 Plasma Cutting Power Supply only. Servicing of this equipment is restricted to properly trained personnel;

unqualified personnel are strictly cautioned against attempting repairs or adjustments not covered in this manual, at

the risk of voiding the Warranty.

Read this manual thoroughly. A complete understanding of the characteristics and capabilities of this equipment will

assure the dependable operation for which it was designed.

NOTE

Refer to the Torch Manual for torch and cutting information.

2.02 Power Supply Specifications

Input Power

Input Power Cable

Output Current

Power Supply Gas

Filtering Ability

Ambient Temperature

IEC

Rating

TDC

Rating

IEC

Rating

TDC

Rating

IEC

Rating

TDC

Rating

Duty Cycle

Current

40 Amps n/a 25 Amps n/a n/a n/a

DC Voltage

96 vdc n/a 90 vdc n/a n/a n/a

Firepower PC-500 Power Supply Specifications

40% 60% 100%

40° C (104° F)

208 / 230 VAC (187 - 253 VAC), Single Phase, 60 Hz

Particulates to 20 Microns. Particulates to 0.85 microns with

additional single-stage filter installed.

20 - 40 Amps, Continuously Adjustable

Firepower PC-500 Power Supply Duty Cycle *

Power Supply includes input cable with plug.

* NOTE: The duty cycle will be reduced if the primary input power (AC) is low

or the output voltage (DC) is higher than shown in this chart.

NOTE:

IEC Rating is determined as specified by the International Electro-Technical Commission. These specifications in-

clude calculating an output voltage based upon power supply rated current. To facilitate comparison between power

supplies, all manufacturers use this output voltage to determine duty cycle.

TDC Rating is determined using an output voltage representative of actual output voltage during cutting with a TDC

torch. This voltage may be more or less than IEC voltage, depending upon choice of torch, consumables, and actual

cutting operation.

INTRODUCTION 2-2 Manual 0-4601

Power Supply Dimensions & Weight Ventilation Clearance Requirements

22.5"

0.57 m

58 lb / 26 kg

A-03700

10.75"

273 mm

16.375"

416 mm

150 mm

A-03379

150 mm

2.03 Input Wiring Specifications

Voltage Freq. 1-Ph 3-Ph 1-Ph 3-Ph

(Volts) (Hz.) (kVA) (kVA) (Amps) (Amps) 1-Ph 3-Ph 1-Ph 3-Ph 1-Ph 3-Ph

208 60 9 39 60 10 10

230 60 9 37 60 10 10

Fuse (Amps) Wire (AWG) Wire (Canada)

Line Voltages with Suggested Circuit Protection and Wire Sizes

Based on National Electric Code and Canadian Electric Code

PC-500 Power Supply Input Wiring Requirements

Input Power Input Current Input Suggested Sizes (See Notes)

NOTES

Refer to Local and National Codes or local authority having jurisdiction for proper wiring requirements.

Cable size is de-rated based on the Duty Cycle of the equipment.

The suggested sizes are based on flexible power cable with power plug installations. For hard-wired installations refer

to local or national codes.

Cable conductor temperature used is 167° F (75° C).

An energy limiting fuse UL Class RK-1 (examples: BUSS LPS / LPN-RK or Gould-Shawmut AZK-A6K) should be

used to minimize damage to Plasma Cutting, Welding or power distribution equipment.

NEVER use replaceable element fuses like UL Class H, or "one-time" fuses like UL Class K5.

Manual 0-4601 2-3 INTRODUCTION

2.04 Power Supply Features

Art # A-03578

Work Cable

and Clamp

Handle and Leads Wrap

Torch Leads Receptacle

Control Panel

A-03739

Input Power Cord

Gas Inlet Port

Gas Pressure Regulator /

Filter Assembly

Gas Pressure Gauge

INTRODUCTION 2-4 Manual 0-4601

2.05 Power Supply Options

Section 6, Parts Lists, provides catalog numbers and or-

dering information.

A. Single-Stage Air Filter Kit

For use with compressed air shop systems. Filters

moisture and particulate matter from the air stream to

at least 0.85 microns.

B. Two-Stage Air Filter Kit

This two-stage air filter is for use on compressed air

shop systems. Filter removes moisture and contami-

nants to at least 5 microns. The filter assembly is pre-

assembled at the factory and need only be attached to

the power supply.

C. Multi-Purpose Cart

Rugged steel cart on easy-rolling rear wheels and front-

mounted swivel casters. Provides maximum mobility

for the power supply and can also serve as a display

cart. Top shelf is 12 " (305 mm) x 20 (508 mm). Steel

handle is 30" (762 mm) high.

Manual 0-4601 3-1 INSTALLATION

SECTION 3: INSTALLATION

3.1 Unpacking

1. Use the packing lists to identify and account for each item.

2. Inspect each item for possible shipping damage. If damage is evident, contact your distributor and / or shipping

company before proceeding with the installation.

3. Record Power Supply and Torch model and serial numbers, purchase date and vendor name, in the information

block at the front of this manual.

3.2 Lifting Options

The Power Supply includes a handle for hand lifting only. Be sure unit is lifted and transported safely and securely.

WARNINGS

Do not touch live electrical parts.

Disconnect input power cord before moving unit.

FALLING EQUIPMENT can cause serious personal injury and can damage equipment.

HANDLE is not for mechanical lifting.

• Only persons of adequate physical strength should lift the unit.

• Lift unit by the handle, using two hands. Do not use straps for lifting.

• Use optional cart or similar device of adequate capacity to move unit.

• Place unit on a proper skid and secure in place before transporting with a fork lift or other vehicle.

INSTALLATION 3-2 Manual 0-4601

3.3 Primary Input Power Connections

CAUTION

Check your power source for correct voltage before plugging in or connecting the unit. The primary power source,

fuse, and any extension cords used must conform to local electrical code and the recommended circuit protection and

wiring requirements as specified in Section 2.03.

This power supply includes a factory - installed input power cable and plug.

1. Check your power source for correct voltage before plugging in the unit.

2. Connect the input power cable (or close the main disconnect switch) to supply power to the system.

CAUTION

The primary power source and power cable must conform to local electrical code and the recommended circuit

protection and wiring requirements (refer to table in Appendix 1).

La page charge ...

Firepower Plasma Cutting Power Supply PC-500 Manuel utilisateur

Marque: Firepower

Modèle: Plasma Cutting Power Supply PC-500

Catégorie: Système de soudage

Taper: Manuel utilisateur

Ce manuel convient également à

Plasma Cutting Power Supply Firepower PC-500

Télécharger le PDF

rapport

dans d''autres langues

English: Firepower Plasma Cutting Power Supply PC-500 User manual

Firepower Plasma Cutting Power Supply PC-500 Manuel utilisateur

Ce manuel convient également à

Firepower Plasma Cutting Power Supply PC-500 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents