Monogram ZIS420 Series Installation Instructions Manual

INSTALLATION

INSTRUCTIONS

Side by Side Refrigerators

With Design Guide

MONOGRAM.COM

Pour obtenir une version française de ce manuel d’instructions,

visitez notre site monogram.com.

Para consultar una version en español de este manual de instrucciones,

visite nuestro sitio de internet monogram.com.

2

Safety Information

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT – Save these instructions for

local inspector’s use. Observe all governing codes and

ordinances.

•

Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions with

your Owner’s Manual for future reference.

If you received a damaged unit, you should immediately

contact your dealer or builder.

Skill Level – Installation of this unit requires basic

mechanical, carpentry and plumbing skills. Proper

installation is the responsibility of the installer. Product

failure due to improper installation is not covered under

the Monogram Warranty. See the Owner’s Manual for

warranty information.

WARNING

Tip Over Hazard.

These appliances are top heavy, especially with any doors open, and must be secured to prevent tipping forward

which could result in death or serious injury. Read and follow the entire installation instructions for securing the

appliance with the anti-tip system.

WARNING

To reduce the risk associated with choking, do not allow children under 3 years of age to have

access to small parts during the installation of this product.

CAUTION

Lifting Hazard

This refrigerator is very heavy. To reduce the risk of person injury during maneuvering and installing this refrigerator, 3

people are required for proper installation of 36” wide model and 4 people are required for proper installation of a 42”

or 48” wide model.

CAUTION

Keep fingers out of the “pinch point” areas; clearances between the doors and between the doors

and cabinet are necessarily small. Be careful closing doors when children are in the area.

WARNING

Electrical Shock Hazard.

Plug into a grounded 3-prong outlet.

Do not remove the ground prong.

Do not use an adapter.

Immediately discontinue use of a damaged supply cord.

If the supply cord is damaged it must be replaced by a

qualified service professional with an authorized service

part from the manufacturer.

Do not use an extension cord with this appliance.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Follow the instructions in the section Grounding the unit.

This appliance must be installed with a means in the

fixed house wiring or circuit breaker for disconnecting the

appliance from the electrical supply after installation.

WARNING

Fire or Explosion Hazard.

Keep flammable materials and vapors away from appliance. Failure to do so can result in fire, explosion,

or death.

For Monogram local service in your area, visit monogram.com or call 800.444.1845.

For Monogram service in Canada, visit monogram.ca or call 800.561.3344.

For Monogram Parts and Accessories, visit monogram.com/use-and-care/parts or call 800.444.1845. In Canada,

call 800.661.1616.

31-1000450 Rev. 1

3

Consignes de Sécurité

AVANT DE COMMENCER

Veuillez lire toutes ces instructions attentivement.

• IMPORTANT – Conservez ces instructions à

l’usage de l’inspecteur local. Observez tous les codes et

décrets en vigueur.

•

Note à l’installateur – Assurez-vous de laisser ces

instructions au consommateur.

•

Note au consommateur - Conservez ces instructions

avec votre manuel d’utilisation pour

consultation ultérieure.

Si vous avez reçu un appareil endommagé, veuillez

communiquer immédiatement avec votre revendeur ou votre

entrepreneur.

Niveau de compétence – L’installation de cet appareil

exige des compétences de base en mécanique, menuiserie

et plomberie. La responsabilité d’une installation adéquate

relève de l’installateur. La garantie Monogram ne couvre

pas les défectuosités du produit causées par une installation

inadéquate. Consultez le manuel d’utilisation pour des

renseignements sur la garantie.

AVERTISSEMENT

Risque de basculement.

Ces électroménagers sont lourds du haut, notamment lorsqu’une porte est ouverte, de sorte qu’ils doivent être fixés pour

prévenir un basculement vers l’avant susceptible d’occasionner des blessures graves ou la mort. Lisez et observez la totalité des

instructions d’installation pour connaître la façon de fixer l’électroménager sur le dispositif antibasculement.

AVERTISSEMENT

Risque d’incendie ou d’explosion

Gardez les matériaux et les vapeurs inflammables à l’écart de l’appareil. L’omission de prendre cette précaution peut entraîner un

incendie, une explosion ou la mort.

AVERTISSEMENT

Pour réduire le risque d’étouffement pendant l’installation de ce produit, ne pas laisser les petites pièces

à la portée des enfants âgés de moins de 3 ans.

ATTENTION

Risque lié à la manipulation d’un objet lourd

Ce réfrigérateur est très lourd. Pour réduire le risque de blessure lors de la manutention de ce réfrigérateur, trois (3) personnes

sont nécessaires pour procéder à l’installation appropriée du modèle 36 pouces, quatre (4) pour l’installation des modèles 42 ou 48

pouces.

ATTENTION

Gardez vos doigts éloignés des points de pincement. Les espaces entre les portes et ceux entre les portes et

l’armoire sont particulièrement restreints. Soyez prudent lorsque vous fermez les portes en présence d’enfants.

AVERTISSEMENT

Risque d’électrocution.

Branchez l’appareil dans une prise à 3 broches mise à la terre.

N’enlevez pas la broche de mise à la terre.

N’utilisez pas un adaptateur.

Cessez immédiatement l’utilisation d’un cordon électrique

endommagé. Si le cordon électrique est endommagé, son

remplacement doit être exécuté par un technicien en réparation

qualifié au moyen d’un cordon de rechange autorisé par le

fabricant.

N’utilisez pas un cordon de rallonge avec cet électroménager.

Le non-respect de ces instructions peut occasionner un décès,

un incendie ou un choc électrique

Suivez les instructions de la section Mise à la terre de l’appareil.

Le circuit électrique auquel cet électroménager sera raccordé

doit comporter un disjoncteur ou un autre dispositif permettant de

couper l’alimentation électrique à l’appareil après l’installation.

Pour joindre le service Monogram de votre région, visitez monogram.com

Pour le service Monogram au Canada, visitez monogram.ca

Pour le service des Pièces et accessoires Monogram, visitez monogram.com/use-and-care/parts.

31-1000450 Rev. 1

4

Información sobre Seguridad

ANTES DE COMENZAR

Lea estas instrucciones en su totalidad y atentamente.

•

IMPORTANTE – Conserve estas

instrucciones para uso del inspector local. Cumpla con

todos los códigos y ordenanzas gubernamentales.

• Nota para el Instalador – Asegúrese de

entregarle estas instrucciones al Comprador.

• Nota para el Consumidor – Guarde estas

instrucciones con su Manual del Propietario para

referencia futura.

Si la unidad que recibió está dañada, se deberá

comunicar de inmediato con su vendedor o fabricante.

Nivel de habilidad – La instalación de esta unidad

requiere un nivel básico de habilidades mecánicas,

de carpintería y plomería. La correcta instalación

del producto es responsabilidad del instalador. Si se

producen fallas en el producto debido a una instalación

inadecuada, la Garantía de Monogram no cubrirá las

mismas. Para obtener información sobre la garantía,

consulte el Manual del Propietario.

ADVERTENCIA

Riesgo de Caídas

Estos electrodomésticos son inestables, especialmente cuando una puerta se encuentre abierta, y deben estar

asegurados a fin de evitar caídas hacia adelante que podrían resultar en la muerte o en lesiones graves. Lea y siga

las instrucciones de instalación en su totalidad para asegurar el electrodoméstico con el sistema anti volcaduras.

ADVERTENCIA

Riesgo de Explosión

Mantenga cualquier material y vapores inflamables, tales como gasolina, alejados del electrodoméstico. Si no se

cumple con esto, se podrá producir una explosión, un incendio o la muerte.

ADVERTENCIA

A fin de reducir el riesgo asociado con descargas, no permita que los niños menores de 3

años de edad tengan acceso a las partes pequeñas durante la instalación de este producto.

PRECAUCIÓN

Riesgo al levantar la puerta

Este refrigerador es muy pesado. A fin de reducir el riesgo de lesiones personales durante la maniobra e instalación

de este refrigerador, se requiere contar con 3 personas para una correcta instalación del modelo de 36” de ancho y

con 4 personas para una correcta instalación del modelo de 42” o 48”.

PRECAUCIÓN

Mantenga los dedos fuera de los espacios de “riesgo de lastimaduras”; los espacios entre

las puertas y entre las puertas y el gabinete son necesariamente pequeños. Tenga el cuidado de cerrar las puertas

cuando se encuentren niños en el área.

ADVERTENCIA

Riesgo de Descarga Eléctrica

Enchufe en un tomacorriente con conexión a tierra de 3

cables.

No elimine el cable de conexión a tierra.

No use un adaptador.

Inmediatamente interrumpa el uso de un cable de

suministro de corriente dañado. Si el cable de corriente se

encuentra dañado, su reemplazo deberá ser realizado por

un profesional calificado del servicio técnico, utilizando una

pieza del servicio técnico autorizada por el fabricante.

No use prolongadores con este electrodoméstico.

Si no se siguen estas instrucciones, se podrá producir la

muerte, incendios o descargas eléctricas.

Siga las instrucciones que figuran en la sección de

Conexión de Tierra de la unidad.

Este electrodoméstico deberá ser instalado por algún

medio en el cableado fijo del hogar o en un disyuntor para

desconectar el electrodoméstico del suministro eléctrico

luego de la instalación.

Para acceder al servicio local de Monogram en su área, visite monogram.com

Para acceder al servicio de Monogram en Canadá, visite monogram.ca

Para acceder a Piezas y Accesorios de Monogram, visite monogram.com/use-and-care/parts

31-1000450 Rev. 1

5

Contents

Safety 2

Instructions for Standard Installation 6

Planning Guide

The Installation Space 7

Dimensions and Clearances 8

Customization Basics 9

Side Panels 9

Refrigerator Location 9

Optional Accessory Kits 9

1/4” Framed Panel Dimensions 10

3/4” Overlay Panel Dimensions 11

130° Door Swing 12

90° Door Swing 13

Dispenser Trim 14

Installation Instructions

Tools, Hardware, Materials 14

Grounding the Unit 15

Step 1. Remove Packaging 16

Step 2. Move the Refrigerator into the House 16

Step 3. Install Water Line 16

Step 4. Installation with Filtration System 17

Step 5. Install Side Panels 17

Step 6. Anti-Tip Procedures 17

Step 7. Level Refrigerator 19

Step 8. Alternate Anti-Tip Procedure 19

Step 9. Adjust Door Swing 20

Step 10. Install Grille Panel 20

Step 11. Install 1/4” Framed Panels 21

Step 11A. Install Overlay Panels 22

Step 12. Connect Water Supply 24

Step 13. Connect Power, Close Grille Panel 25

Step 14. Start Icemaker 25

Step 15. Install Toekick 26

Inspect Final Installation 26

Instructions for Flush Inset Installation 27

Instructions for Stainless Steel Installation 28

Planning Guide

The Installation Space 29

Dimensions and Clearances 30

Customization Basics 31

Side Panels 31

Refrigerator Location 31

130° Door Swing 32

90° Door Swing 33

Installation Instructions

Tools, Hardware, Materials 34

Grounding the Unit 34

Step 1. Remove Packaging 35

Step 2. Moving the Refrigerator into the House 35

Step 3. Install Water Line 36

Step 4. Installation with Water Filtration System 37

Step 5. Install Side Panels 37

Step 6. Anti-Tip Procedure 37

Step 7. Level Refrigerator 38

Step 8, Alternate Anti-Tip Procedure 38

Step 9. Adjust Door Swing 39

Step 10. Connect Water Supply 39

Step 11. Connect Power, Close Grille Panel 40

Step 12. Start Icemaker 40

Step 13. Install Toekick 41

Inspect Final Installation 41

31-1000450 Rev. 1

6

Instructions for Standard Installation

31-1000450 Rev. 1

7

THE INSTALLATION SPACE

*The finished cutout width must be:

35-1/2” (90.17 cm) for 36” models

41-1/2” (105.41 cm) for 42” models

47-1/2” (120.65 cm) for 48” models

Water And Electrical Locations

The opening must be prepared with the electrical and the

cold water supply located as shown.

The Cutout Depth Must Be 24” (60.96 cm)

The refrigerator will project forward, slightly beyond

adjacent cabinetry for standard installation.

Additional Specifications

• A 115 volt 60Hz., 15 or 20 amp power supply is

required. An individual properly grounded branch circuit

or circuit breaker is recommended. Install a properly

grounded 3-prong electrical receptacle recessed into

the back wall. Electrical must be located on the rear

wall as shown.

• Water line can enter the opening through the floor

or back wall. Route SmartConnect™ kit or 1/4” O.D.

copper tubing between the cold water line and the

water connection location. The tubing should be

long enough to extend to the front of the refrigerator.

Installation of an easily accessible shut-off valve in the

water line is required.

Design Guide - Standard Installation

*Finished Width

6-3/4"

Electrical

Area

84 ±1/2"

Finished

Opening

75" From Floor

to Bottom

of Electrical

Area

24"

5"

3-1/2"

Water Supply

3-1/2"

36" Models 12"

42" Models 18"

48" Models 20"

31-1000450 Rev. 1

8

DIMENSIONS AND CLEARANCES

Product Clearances

These refrigerators are equipped with a 3-position door

stop. The factory-set 115° door swing can be adjusted

to 130°, or to 90° on panel models or 90° on stainless

steel models if clearance to adjacent cabinets or walls is

restricted.

Panel Models Only: Allow minimum clearances for

the freezer door (Dimension A) and fresh food door

(Dimension B) for a full 130° door swing and to allow for

pan removal.

For a 90° door swing, allow 4 9/16” (11.59 cm) min.

clearance to a wall. If the 90° door stop position is used,

pan access is maintained, but pan removal is restricted.

See the illustrations on pages 12 and 13 to determine

door swing interaction with adjacent cabinets or

countertops.

Design Guide - Standard Installation

ZIS480

ZISB48

AB C

90° 4-9/16”

(11.59 cm) 4-9/16” (11.59 cm) 28-5/8” (72.71 cm)

130° 15” (38.1 cm) 20” (52.23 cm) 28-5/8” (72.71 cm)

ZIS420

ZISB42

AB C

90° 4-9/16”

(11.59 cm) 4-9/16” (11.59 cm) 26-5/8” (67.47 cm)

130° 13” (33.02 cm) 19” (48.26 cm) 26-5/8” (67.47 cm)

ZISB36 A B C

90° 4-9/16”

(11.59 cm) 4-9/16” (11.59 cm) 20-5/8” (52.23 cm)

130° 13” (33.02 cm) 15” (38.1 cm) 20-5/8” (52.23 cm)

* Shipping height. The

refrigerator can be

adjusted to fit into a

cutout that is 84-1/2”

(214.63 cm) in

height. Use leveling

legs and wheels

for a maximum 1”

(2.54 cm) height

adjustment.

*84"

From

Floor

25-3/4" Framed Models

Depth Including 3/4” panel, 25-15/16”

36", 42" or 48"

Frame to Frame

35", 41",

or 47"

Case Width

83-1/2"

at Rear

B

A

130° Door Swing

(Panel Models Only)

90° Door Swing

23-5/8"

Behind

Frame

C

*4 9/16” Min.

Distance to Wall

115° Door Swing

B

A

Dimensions based on custom handles height of

2 9/16” ( 6.51 cm).

31-1000450 Rev. 1

9

CUSTOMIZATION BASICS:

These refrigerators are designed to be customized with decorative panels. Field installed custom door and grille

panels are required.

SIDE PANELS

Side panels must be

used whenever the sides

of the refrigerator will be

exposed. The 1/4”

(0.63 cm) side panels

will slip into the side

case trim. Secure the

panels to the refrigerator

with stick-on hook and

loop fastener strips.

Order the side panels

from the cabinet

manufacturer.

• Cut a notch in the top

front corner as shown

to allow clearance for

corner keys in the front

side trim.

* Depending on installation height.

*84"

2-9/16"

24"

*3" to 4"

3/16"

1-7/8"

REFRIGERATOR LOCATION

• Do not install the refrigerator where the temperature

will go below 55°F (13°C). It will not run often

enough to maintain proper temperatures.

• Do not install the refrigerator where temperatures

will go above 100°F (37°C). It will not perform

properly.

• Do not install the refrigerator in a location exposed to

water (rain, etc.) or direct sunlight.

• Install it on a floor strong enough to support it fully

loaded (approximately 1500 pounds)..

Design Guide - Standard Installation

OPTIONAL ACCESSORY KITS

ZKLN: Visor handle kit for use on custom panel

models in a standard installation.

31-1000450 Rev. 1

10

Design Guide - Standard Installation

1/4” (0.63 cm) FRAMED PANEL DIMENSIONS

If you choose to install framed panels, they must be cut to the

dimensions shown. The panels will slide into the frame on the

door and grille.

Non-Dispenser Models

If the custom panel is less than 1/4” (0.63 cm) thick and it fits

loosely in the door frame it can be backed up with a piece of filler

material or foam tape to improve the fit.

Fresh Food

Panel

Freezer

Panel

E

D

F

G

A

B

Grille Panel

C

Dispenser

Cutout

11”

Dispenser Cutout

13-5/16"

Side-by-Side (in inches)

Dispenser Cutout

Position

ABCD E F G

36” Models 33-7/8 9 68-3/8 14-9/16 18-9/16 34-3/16 1-7/8

42” Models 39-7/8 9-1/2 68-3/8 14-9/16 24-9/16 34-3/16 1-7/8

48” Models 45-7/8 9-1/2 68-3/8 18-9/16 26-9/16 34-3/16 3-7/8

IMPORTANT NOTE: Maximum total panel weight:

• Fresh food door panel – 75 lbs.(34.0 kg)

• Freezer door panel – 53 lbs. (24.0 kg)

• Grille Panel – 18 lbs. (8.16 kg)

1/4"

Panel

Door

5/16"

Trim

Reveal

The framed panel must be 1/4” (0.63 cm) nominal

thickness to fit the dispenser trim.

IMPORTANT NOTE – DISPENSER MODELS

The refrigerator is supplied with two dispenser trims, one for framed panels and one for overlay panels.

• If the panel is less than 0.250” (0.63 cm) thick, a noticeable gap may be created around the dispenser trim. Foam

tape may be applied on the door to improve the fit.

• If the panel is more than 0.250” (0.63 cm) thick, the dispenser trim cannot be secured to the door.

See Dispenser Trim Fit Example, page 13.

31-1000450 Rev. 1

11

36” Side-by-Side (in inches)

Dispenser Cutout

Position

ABCD E F G

1/4” Backer Panel 33-7/8 9 68-3/8 14-9/16 18-9/16

.10” Spacer Panel 33 8-3/8 67 13-1/4 17-1/4

3/4” Overlay Panel 34-1/8 9-1/4 68-5/8 14-13/16 18-13/16 34-5/16 2

42” Side-by-Side (in inches)

ABCD E F G

1/4” Backer Panel 39-7/8 9-1/2 68-3/8 14-9/16 24-9/16

.10” Spacer Panel 39 8-5/8 67 13-1/4 23-1/4

3/4” Overlay Panel 40-1/8 9-3/4 68-5/8 14-13/16 24-13/16 34-5/16 2

48” Side-by-Side (in inches)

ABCD E F G

1/4” Backer Panel 45-7/8 9-1/2 68-3/8 18-9/16 26-9/16

.10” Spacer Panel 45 8-5/8 67 17-1/4 25-1/4

3/4” Overlay Panel 46-1/8 9-3/4 68-5/8 18-13/16 26-13/16 34-5/16 4

IMPORTANT NOTE – DISPENSER MODELS

The refrigerator is supplied with two dispenser trims, one for framed panels and one for overlay panels. The

overlay dispenser trim is designed to fit a total panel thickness of 1.100”.

• If the panel is less than 1.100” (2.79 cm) a noticeable gap may be created around the dispenser trim.

• If the panel is more than 1.100” (2.79 cm) the dispenser trim cannot be secured to the door.

See Dispenser Trim Fit Example, page 13.

• The overlay panel must be constructed according to the specifications shown to achieve the correct total

thickness.

• Alternative panel construction methods such as securing a 3/4” (1.91 cm) panel to a 1/4” (0.63 cm) backer

panel cannot be used. Another method, routing a 3/4” (1.91 cm) thick panel on all sides, cannot be used. These

methods will not result in the required 1.100” (2.79 cm) panel thickness.

3/4” (1.91 cm) OVERLAY PANEL

DIMENSIONS

For a more custom appearance, overlay panels may

be installed on trimmed models. The overlay panel

must be secured to a 1/4” (0.63 cm) thick backer

panel which slides into the trim. A spacer panel 0.10”

(0.25 cm) thick must be placed between the overlay

and backer panel.

Assemble the panels with glue and screws:

• Center the spacer panel on the backer panel, left to

right and top to bottom. Secure the panels with glue.

• Center the spacer and backer panel on the overlay

panel and secure with glue and screws. Screws

must be countersunk into the backer panel.

NOTE: Left-to-right offset

is not always equal to top-

to-bottom offset.

Spacer Panel

Overlay Panel

Backer Panel

Fresh Food

Panel

Freezer

Panel

E

D

F

G

A

B

Grille Panel

C

Dispenser

Cutout

11”

Dispenser Cutout

13-5/16"

*Cut the dispenser opening after the backer, spacer and overlay

panels have been assembled.

IMPORTANT NOTE: Maximum total weight for the

assembled panels:

• Fresh food door panel – 75 lbs. (34.0 kg)

• Freezer door panel – 53 lbs. (24.0 kg)

• Grille Panel – 18 lbs. (8.16 kg)

.250” + .10” + .750” = 1.100” Total Panel Thickness

0.63 + 0.25 + 1.91 = 2.79 cm

3/4"

Overlay

Panel

1/4"

Backer

Panel

Door

.10"

Spacer

Design Guide - Standard Installation

31-1000450 Rev. 1

12

Design Guide - Standard Installation

1/4"

1/2"

3/4"

1"

1-1/4"

1"

3/4" Overlay

Panel

(Nominal Size)

Stainless Steel

1/4"

1/2"

3/4"

2"

1-1/4"

1-1/2"

1-3/4"

3"

2-1/4"

2-1/2"

2-3/4"

1/4"

1/2"

3/4"

Door

23-7/8" From

Rear of

Refrigerator

1"

Refrigerator

Case

Trim

Top View

130° DOOR SWING

Scale 1:1

IMPORTANT NOTE –

FOR DISPENSER MODELS:

Dispenser models are supplied with two

dispenser trims, one to fit framed panels

and one for overlay panels. Dispenser

trim fit to the custom panel depends on

correct panel thickness. Framed panels

must be 1/4” (0.63 cm) nominal. Overlay

panels should be constructed as shown

to accomplish a total 1.100” (2.79 cm)

thickness. See page 13 for details.

Frameless Cabinets: The case trim

overlaps cabinets at the top and sides.

Therefore, frameless cabinets may require

filler strips to prevent interference with

cabinet door swing. The opening must

allow for filler strips.

31-1000450 Rev. 1

13

1/4"

1/2"

3/4"

1"

1-1/4"

1/4"

1/2"

3/4"

1"

1-1/4"

1-1/2"

23-7/8"

From Rear of

Refrigerator

3/4" Overlay

Panel

(Nominal Size)

Case Trim

Refrigerator

Door

Stainless Steel

Top View

90° DOOR SWING

Scale 1:1

IMPORTANT NOTE –

FOR DISPENSER MODELS:

Dispenser models are supplied

with two dispenser trims, one

to fit framed panels and one for

overlay panels. Dispenser trim

fit to the custom panel depends

on correct panel thickness.

Framed panels must be 1/4”

(0.63 cm) nominal. Overlay

panels should be constructed

as shown to accomplish a total

1.100” (2.79 cm) thickness

. See

page 13 for details.

Frameless Cabinets:

The case trim overlaps

cabinets at the top

and sides. Therefore,

frameless cabinets may

require filler strips to

prevent interference with

cabinet door swing. The

opening must allow for

filler strips.

Design Guide - Standard Installation

31-1000450 Rev. 1

14

TOOLS AND MATERIALS REQUIRED

• Tinsnips to cut banding

• Stepladder

• 1” Bit extension

• Tape measure

• Gloves

• 1/4” Drywall screws

• 5-Gal. Bucket with cover

• 6” Spirit level

• Appliance hand truck

• Tubing cutter

• 7/16” open-end wrench

• #2 Phillips screwdriver

• Drill and appropriate bits

• 5/16”, 7/16” socket

• Safety glasses

• 1-1/8” open end wrench

• Pliers

• 1/4”, 5/16” Combo Rachet

• 35” long 2x4 for Anti-Tip support

• 1/4” copper water line tubing or SmartConnect

™

Refrigerator Tubing kits

• Water shut-off valve

• Custom panels for doors and grille panel

• Screws to secure refrigerator to cabinetry

• Stick-on hook and loop fastener strips for 1/4” side

panels

Installation Instructions - Standard Installation

HARDWARE SUPPLIED

• Water filter bypass plug (on some models)

• Toekick

• 1/4” nut and ferrule

• Dispenser trim for overlay panels (for use with

Custom Panel models).

FLOORING

For proper installation, this refrigerator must be placed

on a level surface of hard material that is at the same

height as the rest of the flooring. This surface should

be strong enough to support a fully loaded refrigerator,

or approximately 1,500 lbs.(680.39 kg).

NOTE: Protect the finish of the flooring. Cut a large

section of the cardboard carton and place under

the refrigerator where you are working.

DISPENSER TRIM FIT EXAMPLES:

(NOT TO SCALE)

1/4” (0.63 cm) FRAMED

PANEL

• The dispenser trim fits over the custom

panel and snaps into the freezer door.

• The clips will not engage the door if the

panel is more than 0.250”

(0.63 cm) thick.

• If the panel is less than 0.250”

(0.63 cm) thick, a noticeable gap may

be created around the dispenser trim.

3/4” (1.91 cm) OVERLAY

PANEL

• The dispenser trim fits over the custom

panel and snaps into the freezer door.

• The clips will not engage the door if the

panel is more than 1.100” (2.79 cm)

thick.

• If the panel is less than 1.100” (2.79

cm) thick, a noticeable gap may be

created around the dispenser trim.

1/4” Dispenser Trim

3/4” Overlay Dispenser Trim

31-1000450 Rev. 1

15

GROUNDING THE REFRIGERATOR

WARNING

Electrical Shock Hazard.

Failure to follow these instructions can result in death,

fire, or electrical shock.

The power cord of this appliance is equipped with a

3-prong (grounding) plug which mates with a standard

3-prong (grounding) wall receptacleto minimize the

possibility of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly grounded.

Where a standard 2-prong wall outlet is encountered,

it is your personal responsibility and

obligation to have it replaced with a

properly grounded 3-prong wall outlet.

DO NOT, UNDER ANY

CIRCUMSTANCES, CUT OR REMOVE

THE THIRD (GROUND) PRONG FROM

THE POWER CORD.

DO NOT USE AN ADAPTER PLUG TO CONNECT

THE REFRIGERATOR TO A 2-PRONG OUTLET.

DO NOT USE AN EXTENSION CORD WITH THIS

APPLIANCE.

MISE À LA TERRE DU RÉFRIGÉRATEUR

AVERTISSEMENT

Risque de choc

électrique.

Le non-respect de ces instructions peut entraîner des

risques d’incendies, des chocs électriques ou la mort.

Le cordon d’alimentation de cet appareil est équipé

d’une fiche à trois broches (pour une mise à la terre)

qui s’adapte à la prise de courant standard à 3 broches

(pour une mise à la terre) pour minimiser les risques de

chocs électriques par cet appareil.

Faites vérifier la prise murale et le circuit électrique par

un électricien qualifié pour s’assurer que le système est

correctement mis à la terre.

Dans le cas d’une prise biphasée, l’installateur a la

responsabilité et l’obligation de la remplacer

par une prise triphasée correctement mise

à la terre.

NE COUPEZ PAS OU N’ENLEVEZ

PAS, SOUS AUCUN PRÉTEXTE, LA

TROISIÈME BROCHE DE MISE À LA

TERRE DU CORDON D’ALIMENTATION.

N’UTILISEZ PAS D’ADAPTATEUR POUR BRANCHER

LE RÉFRIGÉRATEUR À UNE PRISE BIPHASÉE.

N’UTILISEZ PAS DE RALLONGE AVEC CET

APPAREIL.

Installation Instructions - Standard Installation

CONEXIÓN A TIERRA DEL

REFRIGERADOR

ADVERTENCIA

Riesgo de Descarga

Eléctrica

Si no se siguen estas instrucciones, se podrá producir la

muerte, incendios o descargas eléctricas.

El cable de corriente de este electrodoméstico cuenta con

un enchufe de 3 cables (conexión a tierra) que se conecta a

un tomacorriente de pared estándar de 3 cables (conexión

a tierra) para minimizar el riesgo de posibles descargas

eléctricas por parte del mismo.

Contrate a un electricista calificado para que controle el

tomacorriente y el circuito eléctrico, a fin de asegurar que el

enchufe esté correctamente conectado a tierra.

En caso de contar con un tomacorriente de pared de 2

cables, es su responsabilidad y obligación reemplazarlo

por un tomacorriente de pared de 3 cables correctamente

conectado a tierra.

NUNCA, BAJO NINGUNA CIRCUNSTANCIA,

CORTE NI ELIMINE EL TERCER CABLE

(TIERRA) DEL CABLE DE CORRIENTE.

NO USE UN ENCHUFE ADAPTADOR PARA

CONECTAR EL REFRIGERADOR A UN

TOMACORRIENTE DE 2 PATAS.

NO USE UN PROLONGADOR CON ESTE

ELECTRODOMÉSTICO.

31-1000450 Rev. 1

16

Installation Instructions - Standard Installation

STEP 3 INSTALL WATER LINE

• A cold water supply is required for automatic

icemaker operation. The water pressure must be

between 40 and 120 p.s.i. (275-827 kPa).

• Route 1/4” OD copper or SmartConnect

™

plastic

tubing between house cold water line and the water

connection location.

• The tubing should be long enough to extend to the

front of the refrigerator. Allow enough tubing to

accommodate the bend leading into the water line

connection.

NOTE: The only Monogram approved plastic tubing is

supplied in the SmartConnect

™

Refrigerator Tubing

kits. Do not use any other plastic water supply line

because the line is under pressure at all times. Other

types of plastic may crack or rupture with age and

cause water damage to your home.

STEP 2 MOVE THE REFRIGERATOR

INTO THE HOUSE

• Re-use the corner posts from the packaging to protect

stainless steel models. Run the appliance dolly straps

over the posts and under the handles.

• Leave the protective film on the refrigerator until

installation is complete. IMPORTANT: Never lift the

refrigerator by the handle or push against the grille

panel; this could cause damage or misalignment.

• Avoid laying the unit on its back or side to prevent

sealed system restrictions.

STEP 1 REMOVE PACKAGING

WARNING

Tip Over Hazard.

The refrigerator is much heavier at the top than at the

bottom—be careful when moving. When using a hand

truck, handle from the side only.

AVERTISSEMENT

Risque de

basculement Le réfrigérateur est beaucoup plus lourd en

haut qu’en bas. Il faut être prudent lors des déplacements. Si

un diable est utilisé, il faut soulever le réfrigérateur sur le côté

seulement.

ADVERTENCIA

Riesgo de Caídas

El refrigerador es mucho más pesado en su parte superior

que en su parte inferior – tenga cuidado al moverlo. Al usar

un carro manual, sosténgalo de costado únicamente.

• Carefully cut banding at the

top and bottom, remove the

outer carton.

• Slide out the back corner

posts (2).

• Slide the carton off the top of

the cabinet.

NOTE: IT IS NOT

NECESSARY TO LAY THE

CABINET DOWN IN ORDER

TO REMOVE THE SKID!

• The unit is secured to the

skid with 4 slotted tie-down straps. Remove the six

7/16” bolts from the base channels in the tie-downs.

• Remove the six 7/16” bolts securing the straps to the skid.

NOTE: DO NOT ATTEMPT TO ROLL UNIT OFF SKID.

• The support blocks on the bottom of the refrigeration

case must be removed before the refrigerator is taken

off the skid or damage will occur. Carefully tilt the

refrigerator and slide the blocks out from beneath.

• Remove the toekick, taped to the left side of the

refrigerator, and set aside for final installation.

• Lift the refrigerator off the skid with an appliance dolly.

Handle from the sides.

Remove

Tie Downs

WARNING

Connect to potable water supply

only. A cold water supply is required for automatic

icemaker operation. The water pressure must be

between 40 and 120 psi (275-827 kilopascals).

WARNING

ELECTRIC SHOCK HAZARD

Attach tubing clamp using existing hole only. DO NOT

drill into the refrigerator.

Floor

Cold Water Line

AVERTISSEMENT

Raccordez l’appareil à

une alimentation d’eau potable seulement. Une

alimentation d’eau froide est requise pour faire

fonctionner la machine à glaçons et le pichet à

remplissage automatique. La pression d’eau doit se

situer entre 40 et 120 psi. (275 à 827 kPa).

AVERTISSEMENT

RISQUE DE DÉCHARGE

ÉLECTRIQUE

Fixez le collier de serrage dans le trou présent seulement.

NE PERCEZ PAS dans le réfrigérateur.

ADVERTENCIA

Realice la conexión a un

suministro de agua potable únicamente. Se requiere

un suministro de agua fría para el funcionamiento de la

máquina de hielos automática y de la jarra de llenado

automático. La presión del agua deberá estar entre 40

y 120 p.s.i. (275 – 827 kPa).

ADVERTENCIA

PELIGRO DE DESCARGA

ELÉCTRICA

Adhiera la abrazadera de la tubería usando el agujero

existente únicamente. NO perfore el refrigerador.

31-1000450 Rev. 1

17

STEP 3 INSTALL WATER LINE (Cont.)

SmartConnect

™

Refrigerator Tubing Kits are available

in the following lengths:

2’ (.6 m) WX08X10002

8’ (2.4 m) WX08X10006

15’ (4.6 m) WX08X10015

25’ (7.6 m) WX08X10025

Shut off the main water supply.

Turn on the nearest faucet long enough to clear the

line of water.

• Install a shut-off valve between the icemaker water

valve and cold water pipe in a basement or cabinet.

The shut-off valve should be located where it will be

easily accessible.

• Turn on the main water supply and flush debris.

Run about a quart of water through the tubing into a

bucket. Shut off the water supply at the shut-off valve.

NOTE: Saddle type shut-off valves are included in many

water supply kits. Before purchasing, make sure a saddle

type valve complies with your local plumbing codes.

NOTE: Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle valves

are illegal and use is not permitted in Massachusetts.

Consult with your licensed plumber.

Installation Instructions - Standard Installation

STEP 4 WATER LINE

INSTALLATION WITH A REVERSE

OSMOSIS SYSTEM OR OTHER

HOUSEHOLD FILTRATION SYSTEM

Skip this step when not using an RO System or

other household filtration system.

If the water supply to the refrigerator is from a household

filtration system, use the refrigerator’s filter bypass plug.

Using the refrigerator’s water filtration cartridge with the

RO filter can result in hollow ice cubes.

To obtain a free bypass plug, visit monogram.com or

call 800.444.1845. In Canada, visit monogram.ca or call

800.661.1616. The bypass plug is installed in the same

way as a filter cartridge.

The icemaker will not operate without the filter or filter

bypass plug.

Filter Bypass

Plug

Rotate Counterclockwise

to Remove

STEP 5 INSTALL SIDE PANELS

Skip this step when not using side panels.

If you are using 1/4” (0.63 cm) side panels, they should

be inserted into the case trim. Fasten the panels to the

refrigerator with stick-on hook and loop fastener strips

before setting the refrigerator in place.

STEP 6

ANTI-TIP PROCEDURE

WARNING

Tip Over Hazard.

These refrigerators are top heavy, especially with

any doors open, and must be secured to prevent

tipping forward which could result in death or

serious injury. Read and follow the entire installation

instructions for securing the refrigerator with the anti-

tip system.

AVERTISSEMENT

Risque de

basculement

Ces réfrigérateurs présentent une partie supérieure

lourde, en particulier avec une porte ouverte; ils

doivent donc être fixés pour prévenir le basculement

vers l’avant et le risque concomitant de blessure

grave ou fatale. Lisez et suivez les instructions

d’installation complètes pour l’installation du système

anti-basculement.

31-1000450 Rev. 1

18

• Cut a 2” x 4” block, 35” (88.9 cm) long and secure the

block to the mounting brackets provided using #12 or

#14 wood screws.

• Secure the bracket

with wood block to

the back wall so

that it is 84” (213.36

cm) from the

finished floor. Use

#12 or #14 wood

screws. See the

illustration.

• The screws must

penetrate at least

one inch into the

vertical wall studs.

• If metal wall studs, use self-tapping sheet metal

screws in place of wood screws.

IMPORTANT: When the refrigerator is installed under

a soffit or if there is not enough height for this method

of security, brackets cannot be used. Proceed to step

7 to level the refrigerator and then to step 8 to secure

refrigerator to cabinets. The refrigerator must be

secured to prevent tipping.

Installation Instructions - Standard Installation

ADVERTENCIA

Riesgo de Caídas

Estos refrigeradores son inestables, especialmente

cuando una puerta se encuentre abierta, y deberán estar

asegurados a fin de evitar caídas hacia adelante que

podrían resultar en la muerte o en lesiones graves. Lea y

siga las instrucciones de instalación en su totalidad para

asegurar el refrigerador con el sistema anti volcaduras.

STEP 6 ANTI-TIP PROCEDURE (Cont.)

Connect Power Cord:

• Before pushing the refrigerator into the opening, plug

the power cord into the receptacle. The water filter

guard will need to be removed for access (some

models). Remove the 3 screws holding it in place. If

access is still too tight, remove the 2 screws holding

the water filter bracket and move aside. Open the

grille panel and reach into the opening at the back

to grasp the power cord. Pull the power cord into the

opening as you push the refrigerator back. Secure

the bracket and guard with the original screws.

• Gently push refrigerator into the opening with hands

against front corners.

31-1000450 Rev. 1

19

Installation Instructions - Standard Installation

STEP 8 ALTERNATE ANTI-TIP PROCEDURE

The refrigerator must be secured to prevent tipping.

• Raise the grille panel to access case trim.

• Use a 3/16” bit to drill four evenly spaced clearance

holes through the metal top case trim.

• Use a 1/16” bit to drill to pilot holes through the metal

clearance holes and into the wood soffit. The holes

should be centered in the soffit or a 3/4” (1.91 cm)min.

wood brace. The brace spanning the enclosure must

be securely fastened to cabinets on both sides.

• Install four, 1-1/2” drywall screws into the pilot holes.

• Drill screws into adjacent cabinets through side case

trim.

STEP 7 LEVEL REFRIGERATOR

All models have 4-point leveling. The front is supported

by leveling legs, the rear is supported by adjustable

wheels. Both are accessible from the front of the

refrigerator.

• To level the back of the refrigerator, turn the 7/16” hex

nut located above the front wheels. Turn clockwise to

raise or counterclockwise to lower the refrigerator.

• For front leveling, use a 1-1/4” open-end wrench.

• Adjust height of refrigerator to match installation cutout

opening 84-1/2”

(214.63 cm). The refrigerator should be level and

plumb with cabinetry.NOTICE: The rear leveling wheels

and front leveling legs are limited to a maximum height

adjustment of 1” (2.54 cm). If the installation requires

more than 84-1/2” (214.63 cm) height, the installer

should elevate the refrigerator on a sheet of plywood

or runners. Cabinetry trim could also be added across

the top of the opening to shorten the opening. If you

attempt to raise the refrigerator more than 1” (2.54

cm), you will damage the front leveling legs and

the rear leveling wheels. Make adjustments in small

increments.

31-1000450 Rev. 1

20

Installation Instructions - Standard Installation

STEP 9 ADJUST DOOR SWING

NOTE: This refrigerator has a 3-position door stop: 90°,

115°, and 130°. When space does not allow the door to

swing open fully to 115°, you may change the door swing

to a 90° opening. A 130° door swing option is available

for standard installation only. Skip this step if door

opening is satisfactory for your installation situation.

• Open the door to view the bottom hinge. Note the door

stop pin locations. The pin is factory installed in the

115° position.

• Close the door. From below, use pliers to unscrew

the door stop and reinstall into the 130° or 90° position.

STEP 10 INSTALL GRILLE PANEL

To insert the framed or overlay panel into the grille:

• Raise the grille panel to the stop position.

• Loosen the screws on the side trim behind the frame.

Remove the bottom trim.

CAUTION

SHARP EDGE HAZARD

The metal panel may be slippery. Grip the metal

panel firmly so the panel does not slip out of the

frame and cause personal injury or damage to the

frame.

ATTENTION

RISQUE DE COUPURE : ATTENTION

AUX ARÊTES VIVES

Le panneau en métal peut bêtre glissant. Tenir fermement

le panneau en métal, de manière à ce que le panneau

ne glisse pas en dehors du cadre en provoquant des

blessures corporelles ou des dommages au cadre.

PRECAUCIÓN

RIESGO DE EXTREMO FILOSO

Es posible que el panel metálico esté resbaladizo. Tome

el panel metálico de manera firme, de modo que no se

deslice fuera del marco y ocasione lesiones personales o

daños sobre el marco.

• Slide the panel over the metal backer panel and into

the trim.

• If necessary, tap with a wood block until the panel slips

under the top trim piece.

• Reassemble the bottom trim. Tighten the screws.

• Adjust the hinge spring to accommodate the panel

weight, if necessary.

Adjust Nut Below

Spring to Accommodate

Panel Weight

Loosen

Side

Trim

Screw

Loosen

Side

Trim

Screw

31-1000450 Rev. 1

La page est en cours de chargement...

Monogram ZIS420 Series Installation Instructions Manual

Ce manuel convient également à

Monogram ZIS420 Series Installation Instructions Manual

dans d''autres langues

Documents connexes

Autres documents