EDOBE TAKE 6 IR/RF Manuel utilisateur

TAKE 10

10 in 1 Universal Remote Control

TAKE10 IR/RF

User guide 3

Bedienungsanleitung 29

Gebruiksaanwijzing 55

Användermanual 81

Guide utilisateur 105

Guía del usuario 131

Manual do utilizador 157

Manuale per l’utente 183

16-8-2010 2 033000=15090C

TAKE 10

UNIVERSAL REMOTE 10 in1

Button layout

16-8-2010 3 033000=15090C

User Guide

General Security Note

Attention:

For carefree and safe use of this product, please read this manual and safety information

carefully and follow the instructions. Technical manipulation of the product or any changes to

the product are forbidden, due to security and approval issues. Please take care to set up

the device correctly - consult your user guide. Children should use the device only under

adult supervision.

Important: the TAKE 10 must be used according the instructions in this manual and is not

suitable for other purposes.

Avoid the following

• strong mechanical wear and tear

• high temperature

• strong vibrations

• high humidity

Please also respect the additional security notes in the various user guide chapters. To ensure

correct set up please read the manual and security notes carefully.

Battery install and change

The device may only be used with AA Alkaline batteries - never try to connect to another

power supply. When inserting batteries be sure the right polarity is used. Remove the batteries

when the device is not used for a longer period. Make sure that the batteries are not short

circuited and are not disposed in fire (danger of explosion). Batteries do not belong in

children hands. Don’t let batteries lay around openly – they might be swallowed by children

or animals. If this happens see a doctor immediately.

Disposal of batteries:

Batteries are special waste and do not belong in general household waste disposal. Leaking

or damaged batteries can upon contact with skin cause burning or acid damage – if

necessary use suitable gloves.

Please dispose of batteries in accordance with local bylaws.

Congratulations

Congratulations on your purchase of the TAKE 10. The TAKE 10 has the ability to combine

many types of remotes into a single remote. It has many unique features that are available

through the high quality colour screen and the configurable menus. The screen displays icons

that are easily set up to represent your favourite channels. You can select any channel by

simply pressing the key next to the icon that represents the channel.

The TAKE 10 may provide additional functions that are not available on your device, and

there may be functions (e.g., menu functions) that initially may not be controlled by the

remote; but in such cases, the TAKE 10 can easily learn the commands from your original

remote. The TAKE 10 remote is capable of many other features that are also described in this

manual.

16-8-2010 4 033000=15090C

The TAKE 10 can also control X10 RF devices, which allows you to control different electrical

devices located in various physical locations around the house, using radio frequency (RF)

signals. This gives you the freedom to control devices that are not in the same physical

location as the remote.

The TAKE 10 is very intuitive and has built-in Help, but it’s very useful to become familiar with

the remote by first reading this manual. After you’ve become familiar with the TAKE 10, the

first thing you need to do is to install the batteries and setup your remote using the on-screen

instructions.

Thank you for purchasing this remote, and we trust that it will give you many years of service.

Contents

1. Introduction

2. Insert the batteries

3. Button Functions

4. Setup

4.1 Using the Wizard

4.2 Setting Up Your Devices

4.3 Setting Up Your Favourites

5. Using The Remote

6. Learning

6.1 Main Keys

6.2 Side Keys

7. Setting Up More

7.1 Devices

7.2 Favourites

8. Setting up X10 devices

9. Advanced Settings

10. Troubleshooting

11. Tips & Tricks about learning IR codes to a remote

1. Introduction

The TAKE 10 is designed to control up to 10 devices:

E.g.: TV, VCR, DVD, SAT or AUDIO. The TAKE 10 contains a library of codes

that are pre-programmed into the remote control. This library covers

nearly all the audio video products on the market today. The

codes have to be programmed once before use. This can be

done in different ways:

a. Using the Wizard to find the correct infra red codes.

b. Learn the codes from the original remote.

2. Insert the batteries

1. On the back of the remote, push down on the tab and lift the cover off.

2. Insert 3 AA Alkaline batteries taking note of the polarity (+/-).

3. Press the battery cover back into place.

16-8-2010 5 033000=15090C

Please Note - Only use new batteries, some remote functions can fail if old batteries are

used. Never use a combination of new and used batteries.

Battery Saving Feature

By default, the TAKE 10 LCD automatically turns off if no keys are pressed for more than 30

seconds. This helps in extending the life of your batteries. The length of time before the LCD

screen turns off can be adjusted from 2 seconds to 35 seconds. Refer to Advanced Settings in

Chapter 8 for information on how to do this.

Memory

All the devices you set up, their codes, Punch-through settings, your favourites, etc., are

stored in permanent memory whilst you are changing batteries. As a result you will not lose

any of your stored settings when the batteries need replacing.

3. Button Functions

[1] His

/ Hers

Quick access keys for favourites stored under His/Hers groups.

[2] POWER

Turns current device On or Off.

[3] SIDE KEYS

Used to access on-screen features.

[4] LCD

Liquid Crystal Display

[5] MODE

Brings up AV device selection screen on the remote

[6] FAVOURITE

Access favourite groups on the remote LCD.

[7] HOME

Brings up the main menu on the remote LCD.

[8] CHANNEL UP/DOWN

Changes channels, chapter skip function for DVD players, track skip for Audio players.

[9] VOLUME UP/DOWN

Changes the volume level of the device.

[10] OK

Selects menu items for the device you are controlling, or confirms selections on the screen.

[11] MENU

Brings up the Menu screen.

16-8-2010 6 033000=15090C

[12] UP, DOWN, LEFT & RIGHT

Navigation Keys, these buttons allow you to navigate into the menu of the selected device (if

the device you selected has such a menu)

[13] MUTE

Turns the Volume on/off.

[14] EPG

Brings up on-screen program or channel guides.

[15] NUMBERS

Numbers for direct program channel selection.

[16] EXIT

Exit On-Screen Menus/Returns to previous On-Screen selection.

[17] AV

Selects input source.

[18] -/-- (Enter)

Accesses program channels >9 or Enter function.

[19] TEXT HOLD

Holds current Teletext page.

[20] INFO

Brings up program channel information.

[21] TEXT ON

Turns Teletext feature on.

[22] TEXT OFF

Turns Teletext feature off.

[23] RECORD, PLAY, PAUSE, STOP, REW, FF,

Transport buttons to operates your VCR, DVR, or DVD Player.

NOTE: the Record key needs pressed twice to operate.

[24] Colour buttons

Gives you quick access to teletext presets.

16-8-2010 7 033000=15090C

4. Setup

4.1 Using the Wizard

a) After you insert the batteries you can select your preferred language and then the Setup

Wizard screen [1] appears. Press any key at this screen to continue with the wizard. You can

exit at any time by pressing the HOME key (located just below the screen).

[1] [2] [3]

b) Pressing OK at screen [2] takes you to the next screen [3]. Pressing the Left navigation key

on the remote at screen [3] takes you to screen [4] that has 10 yellow arrows. Normally the

Left navigation key will get you back to the previous screen but this screen is an exception to

the rule to help you learn how the remote functions. Pressing the Back key again at screen 4

will take you back.

c) Try pressing the Back key a few times to go back through the Wizard and then follow the

instructions on the screens again to familiarize yourself with how to step through the screens

and go back.

You can go back and forth through the Wizard but once you’ve set up your devices and quit

to save the settings, you won’t see the Wizard again unless you do a Master Reset.

Pressing any of the 10 Side Keys (K1 thru K10) at screen

[4] takes you to the screen where you set up your first

device (TV).

See the Setting Up Your Devices section below.

NOTE: To do a Master Reset: Press the HOME key, select

Setup, select Advanced,

select Clear Settings, then select Master Clear.

This will erase everything you have set up in the remote.

4.2 Setting up your devices

For a known brand

After you have been through the Wizard for the first time, screen [1] shown to the right

appears. This is the start of the Wizard to set up your devices (TV being the first one).

Please note that the device you are setting up will need to be switched on prior to

programming the universal remote.

If you know your brand of TV, select ‘Yes’, this results in a faster search for your TV’s code.

K1

K2

K3

K4

K5

K6

K7

K8

K9

K10

[4]

16-8-2010 8 033000=15090C

Selecting ‘No’ searches the complete library of TV codes, rather than just the codes for your

brand of TV. Please be patient if selecting this option as there are hundreds of IR TV codes to

search through.

[1] [2] [3]

Pressing the Side Key next to ‘Yes’ at screen [1] takes you to screen [2] where the most

common brands of TV are shown.

You can scroll through the brands by pushing the Side Keys adjacent to the ‘Next’ and ‘Back’

text. Screen [2] shows Sony being selected as an example.

Screen [3] asks that you point the Universal Remote directly at your TV and repeatedly press

(not hold) the Power button until your device responds.

Pressing the power button sends the On/Off command to your TV.

The LCD on the Universal Remote will show that you have selected code 1 of xx (xx will vary

by brand) as shown on screen [4].

When your device responds to the On/Off command press the save button.

[4] [5] [6]

Pressing Save will bring up screen [5].

This instructs you to test your remote with your TV, simply push some buttons on the remote

(other than Power) such as Channel Up/Down, Volume Up/Down and Menu.

This test will ensure that you have the correct code for your device as the Power button may

work, but other buttons may not, meaning you might have the incorrect code.

If you do find that some keys do not work select ‘Change Code’ (or the Back button) at

screen [5] to find another code that works.

Selecting ‘Label’ on screen [5] allows you to rename the device, e.g. you could call it “My

TV”.

This is an optional step and can also be done later on. Refer to chapter 4.3 for more details

on changing labels.

16-8-2010 9 033000=15090C

Pressing Save Code at screen [5] takes you to screen [6] where you can set up your Universal

Remote to control a Cable box.

Please note, you can quit at this point and set up other devices later, or you can continue

and set up other devices, such as DVR’s, VCR’s or CD Players.

For a unknown brand

If you select ‘No’ at screen [1] (Do you know what brand you have?) then the procedure will

be very similar, the only difference will be that you will be searching through the entire library

of codes for your device, not just the codes for your brand, e.g. Phillips.

If you select ‘Yes’ when asked if you know your brand, but subsequently didn’t find a code

that works, you will be asked if you want to try again (in case you maybe missed it), or try all

the codes for your device.

If you have tried all codes for your device and still don’t find the right code, you can skip the

device, or select ‘Learn’. If you select Learn you can then learn the commands for your

device from its current remote control’s.

4.3 Setting Up Your Favourites

Once you have been through the Wizard and set up your devices (or at least a TV and

skipped the rest of the device setup) you will arrive at screen [1] below.

[1] [2] [3]

Pressing the Right Navigation Key will take you to screen [2].

Here you can enter a channel using the number keys on the remote. For example you might

enter channel 107. You can also include the ‘Enter’ or ‘OK’ buttons at the end of the channel

if your device requires one of these buttons to be pushed to change the channel, e.g.

‘107Ok’ or ‘107Ent’.

You can now press the Side Key next to Pick Logo on screen [2].

A screen [3] containing channel icons will appear.

Pressing the Next Key (Side Key 10) or the Back Key (Side Key 5) will allow you to scroll through

the icons. In this example we have selected the CNBC icon by pressing the corresponding

Side Key. Screen [4] now shows that we have chosen Channel 4, and the CNBC logo.

The device picked in the sample was Cable, you can change the device by pressing the

Side Key next to ‘Pick Device’.

Each time you activate a favourite the remote will control the device programmed, e.g.

when the CNBC favourite is selected the remote will send a command to your cable box. As

an example you may wish to program a Channel 10 favourite which sends a command to

your TV or Set Top Box.

16-8-2010 10 033000=15090C

[4] [5]

If you wish to add a label to the logo press the Side Key next to the ‘Label’ text. This will take

you to screen [5] with a small label on top of the logo.

Initially, the label will be the channel number but this can be changed by using the numeric

keys in a similar fashion to sending a text message on a mobile phone.

Note – “Triple tap” name entry applies. Tap each numeric key to cycle through ALL caps,

numbers and lower case letters. E.g. repeatedly pressing the number 2 key cycles through

A,B,C,2,a,b,c. Pressing the 9 key cycles through W,X,Y,Z,9,w,x,y,z.

A space can be selected with the 0 (zero) key.

Adding a label is optional, if you don’t want to add a label you can simply select ‘Save’ to

save the settings for this favourite.

You may continue to add up to 10 favourites (more can be added later, see chapter 7.2).

After you have finished setting up your initial set of favourites you will be taken choose

whether the favourites you have just set up are to be stored in the HIS or HERS group (later

you can set up favourites in several other groups.)

Selecting an option will take you to the HIS or HER favourite screen, showing the logos of the

favourites you have just set up.

Please note you can reorder the logos later on.

When you have finished setting up your favourites, press the HOME key (located below the

remote’s LCD screen) to return to the home / main menu screen.

5. Using the remote

Assuming you followed the steps on the previous pages and have

set up some devices and some favourites you are now ready to

use the remote.

Please refer to next sections for details on how to set up more

devices, favourites and other functions.

Pressing either the HIS or HERS key a second time accesses the X10

Home Automation modules that you’ve set up for All Rooms. Use

the Side Keys or the Navigation Buttons to select the icon you want

to control.

16-8-2010 11 033000=15090C

X10 RF Devices

Selecting X10 from the MODE key screen displays the Pick Group screen

[6].

• Press the side key for the room that has the device that you want to

control. (For example, press the Side Key for “Basement.”) The screen

shows the device icons according to the way

“Basement” was set up. (If a Group is grayed-out, then no devices were

set up in that room.)

• Press the Side Key to send a command to the device. The status of

the device changes. You can see the status of the device at the

bottom of the screen; and the icon also changes in appearance.

Extended Features

Any Side Key associated with an icon that has extended features follow with additional

screen(s) that can be used to control the device. In addition, the Main Keys on the TAKE 10

can be used to control X10 devices in unique ways.

Some icons will only provide On or Off functions, some may provide

dimming. It depends on the device’s capabilities. The example shown at

the right [7] has two X10 Home Automation devices, a camera base and

a module that turns outside lights on and off. Pressing the Side Key next to

the camera icon displays an additional screen to control the actions of

the camera (screen 8).

Use the Side Keys to operate the camera by pressing the Side Key and

holding it down for actions that require movement.

The remote’s Main Keys can also be used to control a camera, according

to the following:

• OK/Select will centre the camera.

• UP, Down, Left, and Right navigation keys control the camera pan

features.

• CH up and down changes the camera focus.

• VOL up and down will zoom the lens.

• Numbers 1- 5 can be use for camera presets.

Other Controls

In this example [9], the House icon has a LM12 Lamp Module associated

with it. Pressing the Side Key next to the House icon turns the lights on and

off. Lights can be controlled by using certain Main Keys as follows:

• CH up and down turns the light On and Off.

• VOL up and down controls bright and dim if applicable.

Labeling Feature

Two lines are available for labeling when you label an icon. Screen 10 is

an example of a TM13 labeled with a bath icon. The labels Bath and “Extra Bath”

were associated with the icon. The following is an example of how to use the Label

feature.

• Press the HOME button to display the setup screen. Select Setup.

• Select X10 using the Side Key.

• Select Add/Edit at the next screen using the Side Key.

• Choose the room where you will locate the TM13. For this example choose Basement. Press

the side key to select.

• At the add an X10 device screen, press OK.

[6]

[7]

[8]

[9]

16-8-2010 12 033000=15090C

• Select Pick Device.

• Select Appliances and then scroll until you see the TM13 icon. Select

TM13 using the appropriate Side Key.

• At the following screen select Label.

• Use the appropriate Side Keys to create a Label. The Label feature can

have two lines of labels. Enter each line of the label by pressing the Side

Key for the line number, for example, 1 or 2, and then entering the label

using the alphanumeric keys as shown.

• After entering the label(s), select Save using the Side Key.

• Select Done using the Side Key.

• The Saving Settings screen appears and returns to the setup screen.

X10 Sleep Macro

Do the following to set up a Sleep Macro.

• Set up an X10 device using the Wizard or Add-Edit mode, for example a light in your Living

Room with an LM12 module.

• Select Home/Setup/X10/More/Sleep Macro.

• Select “Pick Module.” The Pick Room screen appears.

• Select the room that has the module you want to control.

• Select the module using the Side Key. Try a simple “Off” command for now, but understand

that you can string many commands from different modules and different rooms together in

conjunction with delays as well.

• Select Save and then Done.

• Select Home/Sleep/X10.

• Press the Side Key to toggle when the command(s) will be sent for 15 minutes to up to an

hour and a half away from the current time.

• Press OK to exit.

Favourite key

Press the HIS or HERS key at any stage to access the favourites you’ve set up. Or press the

FAVORITE key, then select your favourites group. Pressing the Side key next to the logo will

change your device to that channel. Selecting a favourite group that has not yet been set

up, takes you to the Setup Wizard.

Important - Make sure you point the remote at your device until the channel changes.

Pressing a favourite key might send the command for a 3 digit channel e.g. 401, if you don’t

point the remote at your device until all three digits have been sent you might just get

channel 40, or just channel 4. Watch the flickering halo at the bottom left of the screen, it

flickers for each digit sent. It also shows what device is being controlled.

Pressing the HOME key at any time will access the main menu in which you can set up various

remote functions or access other features.

By pressing the MODE key, you will be prompted to select a device type to change the

mode that the remote is in. E.g. if the remote is in Cable mode then the hard keys such as

Channel Up/Down, Volume Up/Down etc. will operate your cable box.

When you select a mode, any extra keys for that mode, and any extra keys you have learned

for that mode are displayed. The current mode of the remote is displayed with an icon in the

lower left of the LCD screen.

Before continuing on with the next section, press the HOME key to return to the main menu

screen. Press the Side Key K5 next to the Help icon and follow the prompts for a tutorial on

how to use the remote.

[10]

16-8-2010 13 033000=15090C

5.1 Quick Power

QuickPower is a way of quickly turning all your devices on or off from one easy to use screen.

Press the HOME button to go to the main menu [1] and press the Side Key next to the

‘QuickPower’ icon.

Only devices you have previously set up are displayed, screen [2], the others are greyed out.

In the example shown, only TV, Cable box and Satellite receiver are configured.

Press any key that isn’t greyed out to send the “Power” command for that device.

[1] [2] [3]

QuickPower for X10 Devices

• Set up an X10 device using the Wizard or Add-Edit mode, for example a light in your Living

Room with an LM12

module.

• Select Home/Setup/X10/More/ QuickPower Macro.

• Select Pick Module, and select the command (s) you want to send. Try a simple “Off”

command for now, but understand that you can string many commands from different

modules and different rooms together in conjunction

with delays as well.

• Select Save and then Done.

• Select Home/QuickPower.

• Press the Side Key next to the X10 icon to trigger the Quick Power Macro.

5.2 Sleep

The Sleep function lets you set any device to turn off after a preset time. You can set the off

time in increments of 15 minutes, up to a maximum of 1 hour and 30 minutes.

To access the Sleep function, press the HOME key to go to the main menu [1], and press the

Side Key next to the ‘Sleep’ icon.

You can now set a sleep timer for any or all of the devices that you

have set up, i.e. any that are not greyed out.

The screen will look the same as the ‘QuickPower’ showed at [2].

If we press the Side Key K1 next to the TV icon once, a sleep timer of 15

minutes will be set.

If we then press Side Key K2 next to the Cable box icon twice, this will

set a sleep timer of 30 minutes.

Finally if we press the Side Key K7 next to the Sat icon five times, a sleep

timer of 1 hour 30 minutes is set.

Timers will be displayed as show in screen [3]. [4]

Pressing OK takes you back to the Home screen and saves your sleep timers. If you then

return to the Sleep screen, you will see the timers have started to count down, as shown on

screen [4].

16-8-2010 14 033000=15090C

Important – Make sure you have the remote pointing at the device(s) you’ve set sleep timers

for so it can send the Power command to the device(s) at the time(s) you have set.

5.3 Macros

Macros are a series of commands triggered with the push of one button. They are very useful

if you want to trigger multiple functions across different devices at one time.

E.g. you may want to watch a DVD, this could involve turning the power on to the TV and

DVD player, changing the TV’s AV input, turning on the surround sound speakers and finally

pressing play on the DVD player.

A Macro can trigger all these commands with a single button.

Tip: Before setting up your macro, write down the series of keystrokes that is composed of on

a sheet of paper.

To set up a Macro, press the HOME Key to return to the main menu [1], and press the Side Key

next to the Macro icon. If you have not set up any Macros, a ‘welcome screen’ will be

displayed, prompting you to set up your first Macro, just press OK to proceed.

Select the first device you wish to include in your Macro by pressing the Side Key next to the

‘Pick Device’ text. The remote will cycle through the devices you have set up, which will be

displayed on the bottom left hand corner. Refer to screen [5] which shows ‘TV’ selected.

[5] [6] [7]

To add a command to the Macro you have two options:

1. Press the key on the remote control that corresponds to the command you wish to send,

e.g. the Power button or the AV input button.

2. Press the Side Key next to the ‘Pick Key’ text, this shows you the ‘extra’ keys (functions

that can’t be accessed via the hard buttons on the remote, these are device specific) and

keys that have been learned for that device. Refer to screen [6] for an example.

Once you have pushed a button on the remote, or selected a function from ‘Pick Key’ you

will see the function/s appear at the top of the screen.

You can now add a time delay to your Macro functions by pressing the Side Key next to the

‘Set Delay’ text, each time you press the ‘Set Delay’ key, a 1 second delay will be added to

the last function added to the macro.

Delays are particularly useful when you have to wait for one function to complete before

sending the command for another function, e.g. You may have to wait a few seconds for

your TV to power up before you can change the channel.

You can continue to add as many functions to your Macro as you require. Once you are

done, press the Side Key next to the Save button. This will take you to a summary screen

showing you all the functions of your Macro. From this screen you can Delete your Macro,

Rename your Macro, e.g. Movie or Cable TV, or you can Add additional functions to your

16-8-2010 15 033000=15090C

Macro by pressing the Side Key next to the ‘Add Key’ text, this will take you back to edit your

Macro.

Once you are happy with your Macro press the Side Key next to ‘Done’. This will save your

settings and return you to the Home screen[1]. To access your saved macros simply click the

Side Key next to the Macro icon on the Home screen[1]. You will be taken to screen [7], to

activate your Macro press the corresponding Side Key.

You can add additional Macros, edit or delete existing Macros by clicking the Side Key next

to the ‘Setup’ icon on the main screen[1].

Then press the Side Key next to the Macros icon this will bring up a list of all the spaces

available in which Macros can be allocated (27 in total), macros that you have already

created will be highlighted in green.

To add a new Macro, click on the Side Key corresponding to an empty macro (one

highlighted in black), this will take you to screen [5], then follow the steps above to configure

you new Macro. By pressing a Side Key next to an existing Macro (one highlighted in green)

you will allow you to edit the Macro.

6. Learning

It is possible to learn commands from an existing remote control and store them under the

Main Keys or Side Keys on the Universal Remote.

At the Home screen[1], press the Side Key next to the Setup icon, then press the Side Key next

to the Learn icon.

Screen [8] will be displayed. Here you can select whether you want to store a learned

command from an existing remote under the 10 Side Keys or the Main keys on the Universal

Remote.

Pressing any of the Side Keys on the left (K1-K5) will select Side Keys.

Pressing any of the Side Keys on the right (K6-K9) will select Main Keys.

If you press a right Side Key (Main Keys) you are going to learn, for example, the Chan Up key

from an existing remote and store it under the Chan Up key on the Universal Remote.

Or learn the Power key from an existing remote and store it under the Power key on the

Universal Remote.

If you press a left Side Key (to select Side Keys) you are going to learn, for example, the DVD

Zoom function from an existing remote and store it under a Side Key on the Universal Remote.

You will then be able to name the Side Key ‘DVD Zoom’ and access this function from the

Mode Screen when the remote is in DVD mode, once you have learned this command.

[8] [9] [10]

16-8-2010 16 033000=15090C

6.1 Main Keys

Once you have selected whether you will store your learned commands under Main Keys or

Side Keys you will be taken to the device selection screen [9]. You can now select the device

you would like to learn keys for. In screen [9] we have only set up TV, Cable box and a

Satellite Receiver, all other devices are greyed out, however you are still able to select any

device to learn a command for.

After you have selected the device, you will be prompted to line up the remotes as shown on

screen [10], and press the key on the Universal Remote that you want to store the learned

command under, e.g. the Power key.

You then press and hold (in this example) the Power key on the other remote, until the display

shows that the command has been successfully learned (screen [11].).

If the screen comes up with Failure, try pressing the key on your existing remote again.

Pressing Done when you have finished will automatically save all of your leaned keys.

Note – for some types of keys you might need to hold the key pressed, but for others a quick

press is sufficient. You may need to experiment with the length of the press if you find learned

keys send a command multiple times. Refer to ‘Tips on Learning’ at the end of this manual.

[11] [12] [13]

6.2 Side Keys

Learning Side Keys is very similar to learning Main Keys. In screen [8], select Side Keys by

pressing any Side Key on the left of the LCD (K1-K5). Select the device you would like to learn

keys for.

Once you have selected a device screen [12] will be displayed that will show the extra keys

set up for that particular device by default. Extra keys are represented by small symbols or

text. Side keys without an extra function are labelled as L5, L6, L7, etc. You now need to

assign a Side Key for the command you are about to learn.

Note – you can overwrite the default extra function keys if required. For this example let’s

select L7. Next, point the remote you would like to learn existing commands. Press OK when

you are ready to proceed. Now press the key on your existing remote you wish to learn, hold

the key pressed until the screen says the command was successfully learned. Refer to ‘Tips on

Learning’ at the end of this manual if you experience any problems at this step.

You can now change the label for the key you have just learned if required (in this case L7)

by selecting Change Label in screen [13]. The label can be a combination of text and

numbers and can be edited using the numeric keypad on the Universal Remote in a similar

fashion to sending a text message on a mobile phone. Select OK to finish and save the

learned command. The next time you set the remote to the mode that you learned this key

under, the screen will now include your newly learned (and renamed key).

16-8-2010 17 033000=15090C

Pressing the MODE key and selecting a device type shows the extra keys and learned keys for

that mode.

Note – you can learn keys from any kind of remote under any mode. You could for example

learn the power keys for your TV, and audio system as well as additional keys for your DVD

player under the DVD mode. Then when you press the MODE key and select DVD, you will be

able to turn on your TV, turn on your audio system, and control your DVD player, all from the

Side Keys on the one screen.

7. Setting Up More

7.1 Devices

When you first turned on the Universal Remote, it is likely that you went through the Wizard

and set up a few devices. The following steps explain how to add more devices without using

the Wizard.

Press the HOME key to display the main menu[1] and press the Side Key next to the Setup

icon. Now press the Side Key next to the Devices icon. From here you can chose the device

you would like to set up.

Note – you do not have to select a device that is greyed out, you can also select an existing

device and change its settings.

From this point, setting up a device is the same as the steps outlined in section 4.2 ‘Setting Up

Your Devices’. You can select Aux 1 or Aux 2 from the Devices screen and then chose any

type of device to set up under either Aux key.

You can now also select any device and change the type by repeatedly pressing the

Change Type key shown in screen [14] to the right. This allows you to have more than one

type of advice, for example a second TV.

[14] [15] [16]

7.2 Favourites

It is likely when you first turned on the Universal Remote that you set up some favourites. The

following steps explain how to add additional favourites.

Press the HOME key to display the main menu[1]. Press the Side Key next to the Setup icon

and press the Side Key next to the Favourites icon. You will be taken to screen [15].

Press the Side Key next to the Wizard icon. And pick the group (screen [16]) that you want to

set up any favourites in, or add more favourites to.

If you pick an existing group that you have previously set up favourites in, for example, HIS,

any new favourites will be added to the ones already set up.

16-8-2010 18 033000=15090C

If you have already set up 10 favourites in that group, a new page will be added (you can

have 10 favourites per page).

Groups that are not set up yet are greyed out, but can still be selected.

From this point adding favourites is the same as the steps outlined in section 4.3 ‘Setting Up

Your Favourites’.

Adding/Editing Favourites

The option ‘Add/Edit’ on screen [15] above lets you add favourites to an existing group, edit

favourites in an existing group, or add favourites to a new group.

Press the Side Key next to the Add/Edit icon to select this option.

Select any group from screen [16] above to add favourites to, or to edit existing favourites.

Pressing the Side Key next to an existing group shows the favourites that you previously set up

in that.

You can now press a Side Key next to one of the existing logos (to edit/change it), or press a

Side Key next to a blank location to add a new favourite.

Press More to add or edit icons a new page, for example you may only want to have four

icons on a single page and other icons on their own separate page.

From this point adding favourites is the same as the steps outlined in section 4.3 ‘Setting Up

Your Favourites’.

Reordering Favourites

The ‘Reorder’ feature lets you move the favourites you previously

setup in a group to a different location of the Remote’s LCD screen.

Press the Side Key next to the Reorder icon to select this function.

Pick the group in which you want to reorder the icons from the group

selection screen (screen [16] on the previous page).

The groups that currently have no favourites in them are greyed out

and cannot be selected.

You’ll then see the screen that displays your favourites.

Press the Side Key corresponding to the favourite you wish to move.

You will notice the logo is marked with a green box, like the ‘ABC’

logo in the example on screen [17]. [17]

Now press the Side Key corresponding to the location you want to move the favourite to.

Note – if you move the favourite to a location that already has a favourite, the two will swap

locations.

Deleting Favourites

The ‘Delete’ option lets you remove favourites that you have previously

set up. Press the Side Key next to the Delete icon to select the feature.

Pick the group in which you want to delete the icons from the group

selection screen (screen [16] on the previous page).

The groups that currently have no favourites in them are greyed out

and cannot be selected. The next displays your favourites.

Press the Side Key corresponding to the favourite you wish to delete.

You will notice the logo is marked with a red X, as can be seen in

example [18]. You can mark multiple logos for deletion if you wish.

Press OK to delete the favourites.

Note - a warning screen will be displayed first allowing you to change your mind. [18]

16-8-2010 19 033000=15090C

Renaming Favourite Groups

The ‘Rename’ option lets you change the names of the groups that

you save your favourites in. For example you may wish to rename HIS

to Dave. Press the Side Key next to the Rename icon.

Pick the group you want to rename from the group selection screen

(screen [19]).

None of the groups have been greyed out, so you can even rename

groups that don’t yet have any favourites in them.

You can now enter the new name for the favourites group using the

numeric keys on the Universal Remote in a similar fashion to writing a

text message on a mobile phone. [19]

When you have entered the name, press OK to save the new name for

the favourites group.

8. Setting Up X10 Devices

The TAKE 10 - coupled with other X10 Home Automation Modules - gives you the ability to

control everything electrical in your home. Once you set up your remote, you can control

most any electrical device from the remote, using the keys that have been configured for

X10 Home Automation Modules.

Description

X10 Home Automation systems use three types of signals - Infrared (IR), Radio Frequency (RF),

and Power Line Carrier (PLC). The TAKE 10 can send either IR, RF signals, or both, depending

on how you’ve set up the remote to control different equipment.

Setting Up Your Remote to Send RF commands

When the TAKE 10 is in X10 mode, it transmits RF commands to X10 devices that respond to

RF signals. The following example describes how to use RF to control a TV (so you can control

it from anywhere in your home). Keep in mind that when you set up a non RF device to be

controlled by RF signals, you need to use any of our video sender

transmitters or powermid receivers, which converts the RF signals it

receives back in to IR signals to turn the TV on or off.

• Press Home [20].

• Select Setup using the Side Key.

• Select More using the Side Key.

• At the following select Wireless.

• The Mode [21] screen appears; select the device you want to set for

RF by pressing its Side Key. (In this example, it’s TV.) The RF symbol

appears on the TV icon. Press OK to Save.

Note: After following the above steps, when you make selections in TV [20]

Mode, you will notice that the transmit signals at the bottom of the

screen are now Green.

This indicates that the remote is sending RF and IR to the TV. If the signals

are in red, it means that the remote is transmitting IR only.

When triggering an X10 module or wall switch using the TAKE 10, the

signal is typically sent from the remote using RF on a specific house

code. The RF signal is received by the transceiver (either TM13, CM15, or

security console) on the matching house code. The transceiver then

forwards the signal onto the house wiring. This is now a PLC signal. Any

modules that match the house and unit code transmitted will either turn [21]

on or off, depending on the signal sent.

16-8-2010 20 033000=15090C

Setting Up the TAKE 10 to control the TM13 Transceiver using Housecode “B.”

The TM13 Transceiver receives RF signals to control lights and appliances. Do

the following to setup this transceiver.

• Press the HOME key to display the setup screen. Select Setup.

• Select X10.

• Select Add/Edit at the next screen.

• Choose the room where you will locate the TM13. For this example choose

Basement.

• Press the Side Key to select.

• At the add an X10 device screen, press OK.

• Select Pick Device.

• Select Appliances and then scroll until you see the TM13 icon. Select TM13

using the appropriate Side Key.

• At the following screen select Address.

• Using the Side Keys, select “B.”

• Select Save using the Side Key.

• Select Done using the Side Key.

• Select Mode Button then the X10 device icon side key.

• Next select the room that you’ve set the device in (Basement).

• Press the icon to test the RF transmission for the device.

In the following example we’ll set up the remote for an LM12 Lamp

Module located in the “Basement.”

• Press the HOME Button to display the Home screen. [22]

• Select Setup using the Side Key.

• Select X10 using the Side Key.

• Select Add/Edit at the next screen using the Side Key.

• Select Basement (for this example) using the Side Key.

• At the Let’s add an X10 device screen, press the OK key to continue.

• Select Pick Device and at the next screen select Lamps using the Side

Keys.

• Go through the following screens to find the correct module using the

Next Side Key.

• Select the LM12 Module by using the Side Key.

• Press Save using the Side Key.

• Select Address using the Side Key.

• Use the Side Keys to set the values to B3. [23]

• Note: The values in the Address screen must match the physical hardware settings for the

LM12 Lamp Module. In this example, the settings are set at B3. This means that B3 matches

the physical settings at the Lamp Module. (See the following example for setting up a Lamp

Module to a B3 setting.)

• Press Save using the Side Key to save the values.

• Select Pick Logo using the Side Key and choose an appropriate image by using the Next

Side Key, and then select the image by using the Side Key.

• Press Save and Done using the Side Keys.

Setting up an LM12 Lamp Module (example)

The following is a basic example of how to set up an X10 Lamp Module (sold separately). See

ebode electronics website for a complete catalogue of Home Automation Modules at

www.ebodeelectronics.eu

.

La page est en cours de chargement...

EDOBE TAKE 6 IR/RF Manuel utilisateur

Ce manuel convient également à

EDOBE TAKE 6 IR/RF Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents