Extron NBP 200 Manuel utilisateur

Marque: Extron

Modèle: NBP 200

Taper: Manuel utilisateur

Ce manuel convient également à

NBP 100

IMPORTANT:

Go to www.extron.com for the complete

user guide,

installation instructions,

and

specifications bef

ore connecting the

oduct to the po

wer source.

Network Button Panel — US Gang Series •

Setup Guide

Overview

The Extron NBP Network Button Panels are fully customizable AV system control interfaces for use with Extron IPCPPro Series

and IPLPro Series Control Processors, and with Extron meeting space collaboration system products. The NBPs in this guide

fit a standard US two-gang or three-gang electrical junction box or mud ring. They have one white and one black faceplate for

each NBP, and a two- or three-gang mud ring. Each NBP button panel has a single LAN port, which supports both power and

communications between the control processor and button panels.

Use Extron Toolbelt software to discover and manage NBP button panels and assign each one a unique IP address. Then use

Extron GlobalConfigurator

(GC) Plus and Professional software, or Global Scripter

programming to configure the control

system, including the buttons on NBPs. Once configured, the AV system can be controlled from any of the NBPs.

This guide provides basic instructions for an experienced installer to install an NBP100 or NBP200 button panel. For more

about the NBPs, see the Network Button Panels User Guide, available on www.extron.com. For details on configuration, see the

software help files.

Front Panel Features

ON OFF

MEDIA

PLAYER

LAPTOP

VIDEO

MUTE

HDMI 1

HDMI 2

WIRELESS

Extron

VIDEO

MUTE

LAPTOP

OFF

ON OFF

MEDIA

PLAYER

LAPTOP

VIDEO

MUTE

HDMI 1 HDMI 2

WIRELESS

RESET

VIDEO

MUTE

LAPTOP

OFF

MAC: 00-05-A6-XX-XX-XX

S/N:

XXXXXXX

XXXXXX

00-05-A6-XX-XX-XX

MAC: 00-05-A6-XX-XX-XX

S/N:

XXXXXXX

XXXXXX

00-05-A6-XX-XX-XX

BBBB

BBB

NBP 100 Front Panel with Faceplate

NBP 100 Front Panel without Faceplate

AAAA

NBP 200 Front Panel with Faceplate

NBP 200 Front Panel without Faceplate

AAAA

Faceplate

EEEE

Mounting Holes (x4)

Mounting Holes (x6)MAC Address

EEEE

Figure 1. Front Panels With and Without Faceplates

Function buttons — Configure these buttons to light and function as desired.

Power buttons — These buttons are usually used to control the power to the display device. The On button has a nub that

can be felt with finger tips.

Volume knob — Configure the volume knob to increment or decrement audio volume.

Volume LEDs — Volume LEDs light to act as a meter to indicate the volume level.

Communications LED — This LED (present on certain

models only) indicates the configuration and connection status

of the NBP (see figure 1 on page 1).

• Unlit — Normal operation (the NBP is configured and

connected to an IPCPPro control processor).

• Blinking red — The NBP has been configured but is not

connected to an IPCPPro control processor.

• Lit steadily — The NBP has not been configured.

Network Button Panel — US Gang Series • Setup Guide (Continued)

Reset button and LED — Pressing this recessed button (see figure 1 on the previous page) causes various product settings

to be reset to the factory defaults (see Reset Modes: a Brief Summary on page7). The LED is normally off except during

resets and immediately after boot-up.

All the function buttons, power buttons, and volume knob must be configured or programmed to carry out their functions. The

buttons are backlit by LEDs.

• Buttons that are configured or programmed but are inactive are dimly lit.

• Buttons that are not configured are dimly lit.

• The NBP buzzes or chirps each time a button is pressed.

Rear Panel Features

LAN (Ethernet) and PoE connector and LEDs — Connect the unit to a network via this connector for control and Power over

Ethernet. Use the following diagrams as a guide.

NBP 200

Rear Panel

YYW W-N -L- M

NBP 100

Rear Panel

YYW W-N -L- M

Side View

Grounding

Screw

LAN/PoE

(Ethernet)

connector

and LEDs

Figure 2. Rear Panel Features

LAN/PoE

RJ-45

Connector

NBP Rear Panel

LAN/PoE (Ethernet and

Power Over Ethernet)

Ethernet

NOTE:

MAC address information

(00-05-A6-XX-XX-XX)

is located on the front panel,

behind the faceplate.

Link LED: Lights

green to indicate a

network connection.

Activity LED:

Blinks

amber to

indicate data

is being sent

or received.

TCP/IP

Network

Extron

IPCP Pro

Control

Processor

Connect to an Ethernet network.

This port must be congured.

Default protocol:

• NBP address: 192.168.254.253

• Gateway IP address: 0.0.0.0

• Subnet mask: 255.255.255.0

• DNS address: 127.0.0.1

• DHCP: off

• Link speed and duplex level: autodetected

• Data rates: 10/100Base-T

Power over Ethernet (PoE):

The NBP receives power at this port.

Default login credentials:

• Username: admin

• Initial password: unit serial number

• Password after a “Reset to Factory

Defaults”: extron

MAC: 00-05-A6-XX-XX-XX

S/N: XXXXXXX EXXXXXX

00-05-A6-XX-XX-XX

MAC: 00-05-A6-XX-XX-XX

S/N: XXXXXXX EXXXXXX

MAC

Address

Figure 3. LAN/PoE Port Details

NOTE: See the grounding instructions on page5.

ATTENTION:

• Power over Ethernet (PoE) is

intended for indoor use only. It is to

be connected only to networks or

circuits that are not routed to the

outside plant or building.

• L’alimentation via Ethernet (PoE) est

destinée à une utilisation en intérieur

uniquement. Elle doit être connectée

seulement à des réseaux ou des

circuits qui ne sont pas routés au

réseau ou au bâtiment extérieur.

IMPORTANT NOTES:

• The factory configured password

for this device has been set to the

device serial number. Passwords are

case sensitive. Performing a Reset to

Factory Defaults (see Reset Modes:

a Brief Summary on page7)

sets the password to extron.

• DHCP is off by default.

Rev. C: Added notes about the factory-set

passwords being the serial number and

about DHCP being off by default.

Installation

Step 1: Get Ready

Use the following check list to prepare for the installation.

 Download and install the latest versions of the software, firmware, and device drivers needed to configure or program the control

processor or HCR receiver to interact with the NBPs and control the connected AV products. See the IPCPPro Series User Guide,

IPLPro Series User Guide, or HC400 Series User Guide (available at www.extron.com) for details on software and drivers.

 Obtain network information for the unit from the network administrator. You need the following details for each IPLinkPro

device, including the IPCPPro and each NBP:

 DHCP setting (on or off)  Subnet mask  User name

 Device (NBP) IP address  Gateway IP address  Passwords

NOTE: If DHCP is on, you do not need the IP addresses and subnet mask.

 Write down the MAC address of each IPLinkPro device (such as the NBP) to be used.

 Obtain model names and setup information for the AV devices to be controlled in the system.

 Each NBP button panel comes with a factory-installed Secure Sockets Layer (SSL) security certificate. If you intend to install

a different SSL certificate, contact your IT department to obtain the certificate or for instructions on how to obtain one. See

“Secure Sockets Layer (SSL) Certificates” in the Network Button Panels User Guide for requirements and guidelines regarding

SSL certificates.

Step 2: Prepare the Installation Site

ATTENTION:

• Installation and service must be performed by authorized personnel only.

• L’installation et l’entretien doivent être effectués par le personnel autorisé uniquement.

• Extron recommends installing the NBP into a grounded, UL Listed electrical junction box.

• Extron recommande d’installer le NBP dans une boîte de dérivation électrique mis à la terre, certifiée UL.

• If the NBP will be installed into fine furniture, it is best to hire a licenced, bonded craftsperson to cut the access hole and

perform the physical installation so the surface will not be damaged.

• S’il est prévu d’installer le NBP dans du beau mobilier, il est préférable de faire appel à un artisan autorisé et qualifié pour

couper le trou d’accès et réaliser l’installation de telle façon que la surface ne soit pas endommagée.

• Follow all national and local building and electrical codes that apply to the installation site.

• Respectez tous les codes électriques et du bâtiment, nationaux et locaux, qui s’appliquent au site de l’installation.

• For the installation to meet UL requirements and to comply with National Electrical Code (NEC), the NBP must be installed

in a ULListed junction box. The end user or installer must furnish the junction box. It is not included with the unit.

• Pour que l’installation respecte les exigences UL et soit conforme au National Electrical Code (NEC) américain, le NBP

doit être installé dans une boîte de dérivation certifiée UL. Il incombe à l’utilisateur final ou à l’installateur de fournir la

boîte de dérivation. Cet équipement n’est pas inclus avec l’unité.

Americans with Disabilities Act (ADA) compliance

When planning where to install the NBP button panels, you may need to consider factors affecting

accessibility of the button panels such as height from the floor, distance from obstructions, and

how far a user must reach to press the buttons. For guidelines, see sections

307 (“Protruding Objects”) and 308 (“Reach Ranges”) of the

2010 ADA Standards for Accessible Design available at

http://www.ada.gov/regs2010/2010ADAStandards/2010ADAStandards.pdf.

Site preparation

Each unit ships with a mud ring. Optional

ULListed in-wall junction boxes, external wall

boxes (EWBs), and surface or tabletop mounting

boxes are available for use with the button panels.

Read any installation instructions and UL

guidelines that come with the mounting devices, then follow the instructions to

install the box or mud ring in the opening at the installation site.

When you run cables to the mounting location, leave enough slack for device

installation. Secure the cables with a clamp for strain relief and so they do not slip

back down into the wall or furniture.

Rev. B: Added note.

Rev. B: Changed French text in the

second Attention

Rev. B: Changed the note to an

Attention & added French text,

per Homi A’s requirement for the

HC products..

Model US Gang Size

NBP 100 2

NBP 200 3

Mud Ring

Wall

Network Button Panel — US Gang Series • Setup Guide (Continued)

Step 3: Change a Faceplate, Button Labels, or Knob (Optional)

The faceplate, button labels, and knob can easily be changed at any time. Some button labels ship with the unit. You can create

and print your own customized labels using Extron Button Label Generator software.

Replacing a faceplate

To replace a faceplate:

1. Remove the faceplate by holding the body of the unit with one hand, gripping the sides of the faceplate with the other hand,

and pulling the faceplate away from the unit.

2. Align the openings of the new faceplate with the buttons and knob and with the LEDs, and place the faceplate against the

unit. The magnetic catches fasten the faceplate onto the unit.

Replacing button labels

To change a button label:

1. Remove the faceplate as described in step 1 of “Replacing a faceplate,” above.

2. For each button label to be replaced, gently separate the button lens cap from its

white diffuser. To to this, insert the end of the provided Extron removal (pry) tool

removal tool into the corner notch and gently twist the tool (see

in the

image at right).

3. Remove the label insert from the translucent button cap.

TIP: If the insert does not come out easily, use a piece of

sticky tape to pull it out of the button cap.

4. Select one of the button labels from the printed label sheets

included with the unit. Remove the label from its backing and

remove the clear, protective film from the front of the label.

5. Insert the button label into the button cap (see

at right).

Check for correct label orientation.

6. Align the cap with the white diffuser and the panel opening,

and press the clear cap into place on the button.

7. Reattach the faceplate to the unit (see step 2 in “Replacing a

faceplate”).

Changing a knob

To change a knob:

1. Remove the faceplate as described in step 1 of

“Replacing a faceplate.”

2. Firmly grasp the knob and pull it away from the NBP.

3. Align the ridge inside the new knob with the channel on

the knob control and allow the magnet in the knob to

snap into place (see

at right).

4. Reattach the faceplate to the unit (see step 2 in

“Replacing a faceplate” and see

at right).

TEXT

Separate the

two-piece button

her

e at the corner.

Dif

fuser

Base

Insert

button label.

Button

Lens Cap

Removal

(Pry) Tool

RESET

ON OFF

MAC: 00-05-A6-XX-XX-XX

S/N: ####### E######

00-05-A6-XX-XX-XX

Extron

Step 4: Cable All Devices

1. If the button panel is not mounted to a grounded metal

junction box or a grounded metal equipment rack, Extron

recommends connecting the unit to an earth ground to

protect the unit from electrostatic discharge.

To ground the unit:

a. Securely terminate a grounding cable with a ring terminal.

b. Remove the grounding screw in the lower left corner

of the rear panel, insert the grounding cable, replace

and securely fasten the screw (see figure 4 at right).

Do not over-tighten the screw. Maximum torque is

2inch-pounds (0.2 Newton-meter).

c. Connect the other end of the grounding cable to an

earth ground.

2. Connect the NBP to the network (see Rear Panel Features

on page2), and cable devices to the control processor or

HCR receiver (see the user guide for the appropriate device).

3. Connect power cords and power on the control processor

or receiver and other devices.

Step 5: Set Up the NBP for Network

Communication

1. Ensure that the PC that you will use for setup and the

NBP button panel are connected to the same Ethernet

subnetwork.

2. Start Toolbelt and use it to set the DHCP status or to

set the IP address, subnet, gateway IP address, DHCP

status, and related settings. Use the flowchart at right

as a guide to setting up the unit for network use.

NOTE: If using a host name instead of an IP

address, the user must enter a qualified host

name (Username.HostName.Domain).

For example: somename.somedomain.com.

Step 6: Configure the System

Use Global Configurator (GCPlus or GCProfessional) to

configure the IPCPPro control processor, IPLPro control processor, or HCR receiver. Alternatively, use Global Scripter to program

the control processor. That configuration sets the control and monitoring behavior for all the AV devices and control accessories

(such as the NBP button panels) in the system. An outline of the main configuration and programming steps is included in the

user guide for the control device.

NOTE: See the Toolbelt Help File, Global Configurator Help File, and Global Scripter Help File as needed for step-by-step

instructions and detailed information. The help file for GC includes an introduction to the software, and how to start a

project and configuration.

When configuration or programming is completed, save the project or program script, then build and upload the system

configuration to the control processor or receiver.

Step 7: Test and Troubleshoot

1. Test the system. See the IPCPPro Series User Guide, IPLPro Series User Guide, or HC400 Series User Guide for an outline

of the system testing and troubleshooting procedure.

2. Make adjustments to wiring or configuration as needed. Remember that the rear panel port on the button panel is not

accessible after the NBP is mounted.

LAN

PoE

NBP 100 Rear Panel

Figure 4. Connecting a Grounding Wire to the NBP

Open the Toolbelt software.

Start Device Discovery.

Toolbelt displays a list of all Extron control devices

connected to the network.

Using the MAC address, locate the desired device

in the list and select it. Enter credentials, if needed.

Network Communication Setup

Connect the NBP and PC to the same network.

Apply power to all devices.

Use the Set IP feature in Toolbelt or

use the Toolbelt

Manage > Network Settings tab

feature either to enable DHCP or to enter the

IP address, subnet address, and gateway, then

congure other network settings as needed.

Figure 5. Network Setup

Rev. B: Added

“Enter credentials,

if needed” and

“enable DHCP or

to...” to the network

setup flowchart.

Rev. B: Deleted

reference to

“during project

recovery”

Network Button Panel — US Gang Series • Setup Guide (Continued)

Step 8: Complete the Physical Installation

Mount the unit to a wall or furniture (see “Mounting”, below).

Mounting

Mount the NBP as follows:

1. Insert the cabled NBP into the mud ring or junction box within the wall or furniture, aligning the mounting holes in the NBP

with those in the box or mud ring.

2. Secure the NBP to the junction box, wall or surface mounting box, or

mud ring as follows (see figures 6 and 7):

a. Insert the included screws through the mounting

holes at the top and bottom of the unit, through

the plastic spacer (if not using a mud ring),

and into the corresponding threaded holes in

the box or mud ring.

NOTE: If the unit is not installed in a

mud ring, you must install the plastic

spacer. The spacer positions the unit

to allow the magnetic faceplate to

attach properly and securely.

b. Using a Phillips screwdriver, lightly tighten

the screws until snug.

ATTENTION:

• Do not overtighten the screws.

• Veillez à ne pas trop serrer les vis.

ON OFF

MAC: 00-05-A6-XX-XX-XX

S/N: ####### E######

00-05-A6-XX-XX-XX

Extron

Wall

Faceplate

NBP 100

Plastic Spacer

Wall Box

3. Attach the wallplate to the NBP: align the faceplate openings with the buttons, knob, and LEDs, and place the faceplate

against the unit (see figures 6 and 7). The magnetic catches fasten the faceplate onto the front of the unit.

MAC: 00-05-A6-XX-XX-XX

S/N: ####### E######

00-05-A6-XX-XX-XX

Extron

Wall

NBP 100

Mud Ring

Faceplate

Figure 6. Installing the NBP in a Mud Ring

Figure 7. Installing the NBP in a Junction Box

NOTE: Extron

recommends taking

precautions to

avoid electrostatic

discharge issues

during installation.

Reset Modes: a Brief Summary

The NBP Series button panels offer the following reset modes:

• Use Factory Firmware: Press and hold the Reset button while applying power to the unit. Keep holding the button

down until the Reset LED blinks twice, or for 6 seconds, then release the button. The unit enters

factory firmware mode. Use this mode to revert to factory firmware in the event of a firmware

failure.

Do not continue to operate the unit using the factory rmware version. If you want to use the

factory default rmware version, you must upload that version again.

• Toggle DHCP Client: Press the Reset button five times (consecutively). Release the button. Do not press the button

within 3seconds following the fifth press. Use this mode to enable or disable the DHCP client

for the LAN port.

• The Reset LED blinks 6 times if the DHCP client is enabled.

• The Reset LED blinks 3 times if the DHCP client is disabled.

NOTES:

• By default DHCP is off and the unit uses a static IP address.

• When you disable the DHCP client, the unit reverts to using the previously-set

static IP address.

• Reset All IP Settings: Press and hold the Reset button for 6 seconds. After the Reset LED blinks twice, release and

momentarily press the Reset button. Use this mode to reset all network settings to factory

default values without affecting user-loaded files.

• Reset to Factory Defaults: Press and hold the Reset button for 9 seconds. After the Reset LED blinks three times, release

and momentarily press the Reset button within 1 second. Use this mode to return the unit to

factory default settings.

For detailed information on each mode and its use, see the Network Button Panels User Guide at www.extron.com.

Resources

Obtaining Instructions, Information, and Assistance

If you have questions during installation and setup, call the ExtronS3 Sales & Technical Support Hotline or the ExtronS3

Control Systems Support Hotline (1.800.633.9877).

Locating Software and Firmware on the Extron Website

There are three main ways to find software and firmware within www.extron.com:

• Via links from the web page for the specific product

• Via the Download page (Click on the Download tab at the top of any page within the website.)

• Via links from search results

NOTES:

• For some software you have the option to click the Download Now button to begin downloading the software file. For

other software there is a link for contacting an Extron support representative who can provide you access to the latest

version.

• To obtain Extron control product software, you must have an Extron Insider account. Extron provides training to our

customers on how to use the software. Access to the full features of Global Configurator Professional is available to

those who successfully complete Extron Control Professional Certification.

Network Button Panel — US Gang Series • Setup Guide (Continued)

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

68-3267-51, Rev. B

09 19

Overall Conﬁguration Procedure

Conﬁgure the IP settings of each NBP

and of the control processor or receiver.

See the network

communication

setup instructions

Create a new GC Professional or GC Plus project

and add the control processor or receiver to it.

Congure ports.

Add NBP button panels and congure the buttons.

Test the system, make adjustments,

nalize conguration.

Save the project.

Cable the NBPs and the control processor or HCR receiver,

then apply power.

Cable all devices.

Prepare the installation site.

Get ready.

Change buttons or faceplates, if desired

Mount the NBPs.

Create monitors, schedules, timers, macros,

and local variables.

Build and upload the conguration to

the controller or receiver.

If desired or required, install a new

security certicate (via Toolbelt).

Within Global Conﬁgurator

(GC Professional or

GC Plus mode):

Figure 8. Overall Configuration Steps

network

communication

setup instructions

on page 5.

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

Extron NBP 200 Manuel utilisateur

Marque: Extron

Modèle: NBP 200

Taper: Manuel utilisateur

Ce manuel convient également à

NBP 100

Télécharger le PDF

rapport

dans d''autres langues

English: Extron NBP 200 User manual

Extron NBP 200 Manuel utilisateur

Ce manuel convient également à

Extron NBP 200 Manuel utilisateur

dans d''autres langues

Documents connexes