Legrand LMCI-100 Computer to DLM Interface Guide d'installation

Legrand
Marque
Legrand
Modèle
LMCI-100 Computer to DLM Interface
Taper
Guide d'installation
Wattstopper
®
Computer to DLM Interface
Installation Instructions • Instructions d’Installation • Instrucciones de Instalación
No: 24986 – 11/16 rev. 1
Catalog Number • Numéro de Catalogue • Número de Catálogo: LMCI-100
Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China
SPECIFICATIONS
Connection to the DLM Local Network: .................... 1 RJ45 port
Voltage .................................................................... 24VDC
Current consumption ................................................... 7mA
Connection to computer: ................................. 1 USB connector
Voltage ...................................................................... 5VDC
Current consumption ................................................. 15mA
Environment:
Operating Temperature ...............32° to 131°F (0° to 55°C)
Storage Temperature ................ 23° to 176°F (-5° to 80°C)
Relative Humidity .....................5 to 95% (non condensing)
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
This unit has no adjustments.
For full operational details and more features of the product, see the DLM System
Installation Guide provided with Wattstopper room controllers, and also available
at www.legrand.us/wattstopper.
Installation shall be in accordance with all applicable regulations, local and
NEC codes. Wire connections shall be rated suitable for the wire size (lead and
building wiring) employed.
For Class 2 DLM devices and device wiring: To be connected to a Class 2 power
source only. Do not reclassify and install as Class 1, or Power and Lighting
Wiring.
CAUTION: TO CONNECT A COMPUTER TO THE DLM LOCAL NETWORK USE THE
LMCI‑100. NEVER CONNECT THE DLM LOCAL NETWORK TO AN ETHERNET PORT
– IT MAY DAMAGE COMPUTERS AND OTHER CONNECTED EQUIPMENT.
DESCRIPTION
The Wattstopper LMCI-100 Computer to DLM Interface is a USB dongle that connects a computer’s USB port to the Digital Lighting
Management (DLM) local network through its RJ45 connector. It works in conjuction with the LMCS-100 Digital Lighting Management
computer software allowing users to read, store configurations, and modify DLM parameters for easy computer based configuration.
CONNECTION DIRECTIONS
Plug the LMCI-100 into a USB port on the computer running the LMCS-100 software. Plug an LMRJ cable from the DLM Local Network
into the RJ45 port on the LMCI-100.
Loads
1
2
Line
Voltage
Room
Controller
J-Box
Switch
LMCI-100 Computer to
DLM Interface
Sensor
DLM Local
Network
POWER‑UP FUNCTIONALITY
Upon connecting the LMCI-100 to a computer running the LMCS-100 DLM software and then
to the DLM local network, the LMCI-100 is ready to send and receive signals from the DLM
system.
The power LED (green) on the LMCI-100 turns on indicating the unit is receiving power from
the computer’s USB port. The communication LED (red) blinks to indicate it is sending and
receiving DLM messages and passing them through the USB connection.
Communication LED
Red
USB Power LED
Green
Connect to DLM local
network only,
NOT Ethernet
USB Connector
800.879.8585
www.legrand.us/wattstopper
No. 24986 – 11/16 rev. 1
© Copyright 2016 Legrand All Rights Reserved.
© Copyright 2016 Tous droits réservés Legrand.
© Copyright 2016 Legrand Todos los derechos reservados.
Wattstopper warranties its products to be free
of defects in materials and workmanship for a
period of five (5) years. There are no obligations
or liabilities on the part of Wattstopper for
consequential damages arising out of, or in
connection with, the use or performance of this
product or other indirect damages with respect
to loss of property, revenue or profit, or cost of
removal, installation or reinstallation.
Wattstopper garantit que ses produits sont
exempts de défauts de matériaux et de fabrication
pour une période de cinq (5) ans. Wattstopper
ne peut être tenu responsable de tout dommage
consécutif causé par ou lié à l’utilisation ou
à la performance de ce produit ou tout autre
dommage indirect lié à la perte de propriété, de
revenus, ou de profits, ou aux coûts d’enlèvement,
d’installation ou de réinstallation.
Wattstopper garantiza que sus productos
están libres de defectos en materiales y mano
de obra por un período de cinco (5) años. No
existen obligaciones ni responsabilidades por
parte de Wattstopper por daños consecuentes
que se deriven o estén relacionados con el
uso o el rendimiento de este producto u otros
daños indirectos con respecto a la pérdida
de propiedad, renta o ganancias, o al costo
de extracción, instalación o reinstalación.
WARRANTY INFORMATION INFORMATIONS RELATIVES À LA GARANTIE INFORMACIÓN DE LA GARANTÍA
TROUBLESHOOTING
Power LED is not on. 1. Check that the unit is connected to the USB port of a computer.
2. Check that the computer is on and running the LMCS-100 DLM software package.
The communication LED
is not on and doesn’t
blink.
1. Check that the unit is connected to the USB port of a computer.
2. Check that the computer is on and running the LMCS-100 DLM software package.
3. Check that the LMCI-100 is connected to the DLM local network through its RJ45 port:
Unplug the LMRJ cable from the LMCI-100 then plug in a different DLM device to that LMRJ cable.
If the device does not power up, recheck DLM local network connections between the LMCI-100
and the room controller.
  • Page 1 1
  • Page 2 2

Legrand LMCI-100 Computer to DLM Interface Guide d'installation

Legrand
Marque
Legrand
Modèle
LMCI-100 Computer to DLM Interface
Taper
Guide d'installation
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes