Simplicity 076003LP- Guide d'installation

Questions?

Help is just a moment away!

Call: Residential Generator Helpline

(877) 369-9400 M-F 8-5 CT

45000 Watt

Residential Generator

System

Installation and Start-Up Manual

GEN42WN & GEN45WL

2

Thank you for purchasing this quality-built Rheem / Ruud residential generator. We are pleased that you’ve placed your

confidence in the Rheem or Ruud brand. When operated and maintained according to the instructions in the operator’s

manual, your residential generator will provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with residential generator

systems and how to avoid them. This generator system is designed and intended only for use as an optional residential

standby system that provides an alternate source of electric power and to serve loads such as heating, refrigeration systems,

and communication systems that, when stopped during any power outage, could cause discomfort or inconvenience. Save

these instructions for future reference.

This generator system requires professional installation before use. Your installer should follow the instructions completely

Where to Find Us

You never have to look far to find support and service for your generator. Consult your Yellow Pages. There are many

Rheem and Ruud authorized service dealers who provide quality service. You can also contact customer service by phone at

(877) 369-9400 between 8:00 AM and 5:00 PM CT.

For Future Reference

Please fill out the information below and keep with your receipt to assist in unit identification for future purchase issues.

Date of Purchase

Generator

Model Number

Model Revision

Serial Number

Engine

Model Number

Serial Number

Rheem Sales Company

Randleman, NC 27317

(877) 369-9400

may be reproduced or transmitted in any form without the express

written permission of Rheem Sales Company.

3

Table of Contents

Important Safety Instructions........................4

Installation ....................................7

Home Owner Responsibilities ...................................7

Installing Dealer/Contractor Responsibilities ........................7

Delivery Inspection............................................7

Generator Location............................................8

Fuel Consumption ...........................................12

System Connectors ..........................................13

Grounding the Generator ......................................14

System Control Panel.........................................15

Final Installation Considerations ................................15

Initial Start-up (No Load)......................................16

Test Shutdown(s) Procedure ...................................17

Fuel Conversion .............................................18

Schematic Diagram ..........................................20

Wiring Diagram .............................................21

Operation .................................... 22

Automatic Operation Sequence .................................22

Setting Exercise Timer ........................................22

Installation Inspection ........................................22

4

Important Safety Instructions

SAVE THESE INSTRUCTIONS - This manual contains

important instructions that should be followed during

installation and maintenance of the generator and batteries.

Safety Symbols and Meanings

The safety alert symbol indicates a potential personal

injury hazard. A signal word (DANGER, WARNING, or

CAUTION) is used with the alert symbol to designate a

degree or level of hazard seriousness. A safety symbol may

be used to represent the type of hazard. The signal word

NOTICE is used to address practices not related to

personal injury.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE addresses practices not related to personal injury.

Save These Instructions

Fire

Toxic Fumes

Explosive Pressure

Rotating Fan Blade

Lift Hazard Read Manual

Exploding BatteryRotating Belt/Pulley

Chemical BurnAuto Start

Hot SurfaceRotating Parts

Electrical ShockExplosion

The manufacturer cannot possibly anticipate every possible

circumstance that might involve a hazard. The warnings in

this manual, and the tags and decals affixed to the unit are,

therefore, not all-inclusive. If you use a procedure, work

method or operating technique that the manufacturer does

not specifically recommend, you must satisfy yourself that

it is safe for you and others. You must also make sure that

the procedure, work method or operating technique that you

choose does not render the generator system unsafe.

WARNING Running engine gives off carbon

monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide can cause headache,

fatigue, dizziness, vomiting, confusion, seizures,

nausea, fainting or death.

Operate generator ONLY outdoors.•

Install a battery operated carbon monoxide alarm near •

the bedrooms.

Keep exhaust gas from entering a confined area through •

windows, doors, ventilation intakes, or other openings.

WARNING The engine exhaust from this product

contains chemicals known to the State of California to

cause cancer, birth defects, or other reproductive harm.

WARNING Certain components in this product and

related accessories contain chemicals known to the State

of California to cause cancer, birth defects, or other

reproductive harm. Wash hands after handling.

WARNING Storage batteries give off explosive

hydrogen gas during recharging.

Slightest spark will ignite hydrogen

and cause explosion.

Battery electrolyte fluid contains

acid and is extremely caustic.

Contact with battery contents will cause severe

chemical burns.

A battery presents a risk of electrical shock and high short

circuit current.

DO NOT dispose of battery in a fire. Recycle battery.•

DO NOT allow any open flame, spark, heat, or lit cigarette •

during and for several minutes after charging a battery.

DO NOT open or mutilate the battery.•

Wear protective goggles, rubber apron, rubber boots and •

rubber gloves.

Remove watches, rings, or other metal objects.•

Use tools having insulated handles.•

5

WARNING Generator produces hazardous voltage.

Failure to properly ground generator can result in

electrocution.

Failure to isolate generator from power utility can

result in death or injury to electric utility workers

due to backfeed of electrical energy.

When using generator for backup power, notify •

utility company.

DO NOT touch bare wires or bare receptacles.•

DO NOT use generator with electrical cords which are •

worn, frayed, bare or otherwise damaged.

DO NOT handle generator or electrical cords while •

standing in water, while barefoot, or while hands or

feet are wet.

If you must work around a unit while it is operating, •

stand on an insulated dry surface to reduce the risk of

a shock hazard.

DO NOT allow unqualified persons or children to operate •

or service generator.

In case of an accident caused by electrical shock, •

immediately shut down the source of electrical power and

contact the local authorities. Avoid direct contact with

the victim.

Despite the safe design of the residential generator, •

operating this equipment imprudently, neglecting its

maintenance or being careless can cause possible

injury or death.

Remain alert at all times while working on this equipment. •

Never work on the equipment when you are physically

or mentally fatigued.

Before performing any maintenance on the generator, •

disconnect the battery cable indicated by a NEGATIVE,

NEG or (-) first. When finished, reconnect that cable last.

After your system is installed, the generator may crank •

and start without warning any time there is a power

failure. To prevent possible injury, always set the

generator’s system switch to OFF, remove the service

disconnect from the disconnect box AND remove the

15 Amp fuse BEFORE working on the equipment.

WARNING Propane and Natural Gas are extremely

flammable and explosive.

Fire or explosion can cause severe burns

or death.

Install the fuel supply system according to NFPA 37 and •

other applicable fuel-gas codes.

Before placing the generator into service, the fuel system •

lines must be properly purged and leak tested.

After the generator is installed, you should inspect the fuel •

system periodically.

NO leakage is permitted.•

DO NOT operate engine if smell of fuel is present or other •

explosive conditions exist.

DO NOT smoke around the generator. Wipe up any oil •

spills immediately. Ensure that no combustible materials

are left in the generator compartment. Keep the area near

the generator clean and free of debris.

WARNING Contact with muffler area can result in

serious burns.

Exhaust heat/gases can ignite combustibles

or structures causing a fire.

DO NOT touch hot parts and AVOID hot exhaust gases.•

Allow equipment to cool before touching.•

DO NOT install the generator closer than 5 feet (1.5m) •

from any combustibles or structures with combustible

walls having a fire resistance rating of less than 1 hour.

Keep at least minimum distances shown in • General

Location Guidelines to insure for proper generator cooling

and maintenance clearances.

It is a violation of California Public Resource Code, •

Section 4442, to use or operate the engine on any forest-

covered, brush-covered, or grass-covered land unless

the exhaust system is equipped with a spark arrester, as

defined in Section 4442, maintained in effective working

order. Other states or federal jurisdictions may have

similar laws.

Contact the original equipment manufacturer, retailer, or

dealer to obtain a spark arrester designed for the exhaust

system installed on this engine.

Replacement parts must be the same and installed in the •

same position as the original parts.

6

WARNING Moving parts can crush and cut.

Starter and other rotating parts

can entangle hands, hair, clothing,

or accessories.

NEVER operate generator without protective housings, •

covers, or guards in place.

DO NOT wear loose clothing, jewelry or anything that may •

be caught in the starter or other rotating parts.

Tie up long hair and remove jewelry.•

Before servicing, remove 15 Amp fuse from control panel •

and disconnect Negative (NEG or -) battery cable.

WARNING Hot pressurized coolant can cause severe

injury and/or property damage.

DO NOT open radiator cap when hot.•

Before servicing, allow coolant to cool.•

CAUTION Installing the 15A fuse could cause the

engine to start.

Observe that the 15 Amp fuse has been removed from the •

control panel for shipping.

DO NOT install this fuse until all plumbing and wiring has •

been completed and inspected.

CAUTION Excessively high operating speeds increase

risk of injury and damage to generator.

Excessively low speeds impose a heavy load on generator.

DO NOT tamper with governed speed. Generator supplies •

correct rated frequency and voltage when running at

governed speed.

DO NOT modify generator in any way.•

NOTICE Improper treatment of generator can damage it

and shorten its life.

Use generator only for intended uses.•

If you have questions about intended use, contact your •

authorized dealer.

Operate generator only on level surfaces.•

Adequate, unobstructed flow of cooling and ventilating air •

is critical to correct generator operation.

The access panels/doors must be installed whenever the •

unit is running.

DO NOT expose generator to excessive moisture, dust, •

dirt, or corrosive vapors.

Remain alert at all times while working on this equipment. •

Never work on the equipment when you are physically

or mentally fatigued.

DO NOT start engine with air cleaner or air cleaner •

cover removed.

DO NOT insert any objects through cooling slots.•

DO NOT use the generator or any of its parts as a step. •

Stepping on the unit can cause stress and break parts.

This may result in dangerous operating conditions from

leaking exhaust gases, fuel leakage, oil leakage, etc.

If connected devices overheat, turn them off and •

disconnect them from generator.

Shut off generator if: •

- electrical output is lost;

- equipment sparks, smokes, or emits flames;

- unit vibrates excessively.

NOTICE Exceeding generators wattage/amperage

capacity can damage generator and/or electrical devices

connected to it.

See • Essential Circuits in operator’s manual.

Start generator and let engine stabilize before connecting •

electrical loads.

WARNING Hazardous Voltage - Contact with power

lines can cause electric shock or burn.

Lifting Hazard / Heavy Object - Can cause

muscle strain or back injury.

If lifting or hoisting equipment is used, DO NOT contact •

any power lines.

DO NOT lift or move generator without assistance.•

Use lifting pipes as described in • Lifting the Generator.

The unit may shift on the lifting pipes during movement,

which can cause injury.

DO NOT lift unit by roof as damage to generator •

will occur.

7

Installation

Equipment Description

This product is intended for use as an optional residential

generator system which provides an alternate source

of electric power and to serve loads such as heating,

refrigeration systems, and communication systems that,

when stopped during any power outage, could cause

discomfort or inconvenience. This product does not qualify

for emergency standby as defined by NFPA 70 (NEC).

Every effort has been made to ensure that information in this

manual is accurate and current. However, we reserve the

right to change, alter, or otherwise improve the product and

this document at any time without prior notice.

Home Owner Responsibilities

 • Readandfollowtheinstructionsgivenintheoperator’s

manual, especially the section regarding selecting

essential circuits.

 • Followaregularscheduleinmaintaining,caringfor

and using your residential generator, as specified in the

operator’s manual.

Installing Dealer/Contractor Responsibilities

 • Readandobservethesafetyrules.

 • InstallonlyanULapprovedtransferswitchthatis

compatible with the generator.

 • Readandfollowtheinstructionsgiveninthis

installation and start-up manual.

IMPORTANT: The system is equipped with a water heater

that is activated when ambient temperature is less than 80°F

AND utility power is present at the transfer switch.

If you need more information in this matter, please call

(877) 369-9400 between 8:00 AM and 5:00 PM CT.

Unpacking Precautions

The unit is shipped ready for installation on a prepared

reinforced cement slab or engineered base. Avoid

damage from dropping, bumping, collision, etc. Store and

unpack carton with the proper side up, as noted on the

shipping carton.

Delivery Inspection

After removing the carton, carefully inspect the generator for

any damage that may have occurred during shipment.

IMPORTANT: If loss or damage is noted at time of delivery,

have the person(s) making delivery note all damage on the

freight bill and affix his signature under the consignor’s

memo of loss or damage. If loss or damage is noted after

delivery, separate the damaged materials and contact the

carrier for claim procedures. Missing or damaged parts are

not warranted.

Shipment Contents

The generator system is supplied with:

 • Fully-servicedcoolantsystem

 • Fully-servicedoil/lubricatingsystem

 • Flexiblefuelhook-uphose

 • Installationandstart-upmanual

 • Operator’smanual

 • Engineoperator’smanual

 • Installationchecklist

 • Spareaccessdoorkeys

 • Spare15AmpATO-typefuse

 • Ten-polecontrolpanelconnector

 • Touchuppaint

 • RemoteLEDindicatorkit(LED/plate/screws)

Not Supplied:

 • Startingbattery(seepage16)

 • Reinforcedconcretepad

 • Connectingwireandconduit

 • Fuelsupplyvalves/plumbing

 • Variousspecialtoolsandequipment

 • Two60”lengthsof2”Schedule40pipe(NOTconduit)

 • Crane,liftingstraps,chainsorcables

 • Holepunchesfor7gasteel

 • Torquescrewdriver,5to50inch-poundrange

 • Voltage/frequencymeter

 • Ignitiontiminglight(ifconvertingfueltype)

 • AirFuelRatioMeter(O

2

Sensor and Analyzer, if

converting fuel type)

 • Dummyload(ifconvertingfueltype)

8

Generator Location

Before installing the generator, consult with the homeowner

and convey the following guidelines, which may affect the

desired location.

Install generator outdoors in an area which will not

accumulate deadly exhaust gas. DO NOT install generator

where exhaust gas could accumulate and enter inside or be

drawn into a potentially occupied building. Ensure exhaust

gas is kept away from windows, doors, ventilation intakes

or other openings that can allow exhaust gas to collect in a

confined area. Prevailing winds and air currents should be

taken into consideration when positioning generator.

General Location Guidelines

 • InstalltheunitoutdoorsONLY.

 • Placetheunitonapreparedconcreteslabthatisflat,

level, and has provisions for water drainage.

 • Installtheunitinalocationwheresumppump

discharge, rain gutter down spouts, roof run-off,

landscape irrigation, or water sprinklers will not flood

the unit or spray the enclosure and enter any air inlet or

outlet openings.

 • Installtheunitwhereitwillnotaffectorobstruct

any services (including covered, concealed and

underground), such as telephone, electric, fuel,

irrigation, air conditioning, and so forth.

 • Installtheunitwhereairinletandoutletopeningswill

not become obstructed by leaves, grass, snow, etc. If

prevailing winds will cause blowing or drifting, you may

need to construct a windbreak to protect the unit.

 • Installthegeneratorascloseaspossibletothetransfer

switch and fuel supply to reduce the length of wiring,

conduit, and piping.

IMPORTANT: Laws or local codes may regulate the distance

to the fuel supply.

The minimum (MIN) clearances from aerial view of generator

(B) to combustible (D), and non-combustible (A) materials is

shown below.

 • Thesedistancesareprovidedtogivegeneratorlocation

guidance relative ONLY to combustibles, generator

cooling, and maintenance.

 • Theminimumdistancesinthefigureareasshown.

All four sides of the generator cannot be enclosed

or restricted, even if the minimum distances are

maintained. DO NOT connect (A) and/or (D) to (E).

 • Aroofcannotbeused.

 • Exhaust(C) must not be allowed to accumulate.

A Non-Combustible material with Fire Resistant Rating of

1 hour or greater

B Residential Standby Generator

C Engine Exhaust

D Combustible Material or Structure with a Fire

Resistance Rating of less than 1 hour

E Any structure or material. DO NOT connect (A) and/or

(D) to (E)

WARNING Running engine gives off carbon

monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide can cause headache,

fatigue, dizziness, vomiting, confusion, seizures,

nausea, fainting or death.

Operate generator ONLY outdoors.•

Install a battery operated carbon monoxide alarm near •

the bedrooms.

Keep exhaust gas from entering a confined area through •

windows, doors, ventilation intakes, or other openings.

WARNING Exhaust heat/gases can ignite

combustibles or structures causing a fire.

DO NOT install the generator closer than 5 feet (1.5m) •

from any combustibles or structures with combustible

walls having a fire resistance rating of less than 1 hour.

A

B

E

D

E

C

2’

(.6m)

5’ (1.5m)

5’ (1.5m) 5’ (1.5m)

5’ (1.5m)

3’

(.9m)

2’

(.6m)

9

Concrete Slab

At the appropriate location, construct a concrete slab:

 • 28daycompressionstrengthof3000psi(200MPa)

 • Minimum5inchesthick

 • Minimum6incheswiderthanenclosureonallsides

(shown as D in figure)

 • StrengthenslabwithNo.6reinforcingbars(on

12”centers)or8ga.steelwirefabric(6”centers).

NOTE: Avoid placing reinforcement in entrance

stub-up area (B).

Attach unit to slab at four corner locations (A) with minimum

5/16”diameter(8mm)masonryanchorboltslongenoughto

secure the unit.

The fuel inlet location (C) and the exhaust opening (E) are

shown for reference.

Electrical and Fuel Inlet Locations

A through-slab power cable stub-up is preferred (see

(B) above). If stub-up’s are not used, (F) indicates the

recommended location for punching holes for attaching

power conduit. The 1 inch N.P.T. fuel inlet connector (C) is

shown for reference.

Lifting the Generator

The generator weighs more than 2,075 pounds (941 kg).

Proper tools, equipment and qualified personnel should be

used in all phases of handling and moving the generator.

Two60”lengthsof2”Schedule40pipe(G), supplied by the

installer, are required to lift the generator onto cement pad.

Insert pipes through the lifting holes (H) located near the

unit’s base.

Use a spreader bar to ensure that the chains, straps or

cables DO NOT touch the generator’s roof. Retouch any

chipped paint with supplied touch-up paint.

G

H

C

F

WARNING Hazardous Voltage - Contact with power

lines can cause electric shock or burn.

Lifting Hazard / Heavy Object - Can cause

muscle strain or back injury.

If lifting or hoisting equipment is used, DO NOT contact •

any power lines.

DO NOT lift or move generator without assistance.•

Use lifting pipes as described in • Lifting the Generator.

The unit may shift on the lifting pipes during movement,

which can cause injury.

DO NOT lift unit by roof as damage to generator •

will occur.

49”

19”

108”

92”

59”

9.5”

7”

7.38”

34.25”

10.13”

8”

Slab Top VIew

A

D

C

E

B

10

Access Ports

The residential generator is equipped with an enclosure that

has several access doors, as shown above. The doors are

named for a significant component located behind them,

as follows:

A. Fuel Inlet port (shown for reference)

B. Control Panel door (may be two doors)

C. Exhaust opening (shown for reference)

D. Coolant/Oil Fill door

E. Battery door

The Coolant Fill, Battery and Control Panel doors must be

installed whenever the unit is running to assure proper

cooling, reduce noise and for added safety.

Each residential generator is shipped with a set of identical

keys. These keys fit the locks that secure the access doors.

To open access door:

1. Insert key into lock of access door handle and turn key

one quarter turn counterclockwise.

2. Grasp door’s handle and turn one quarter turn

counterclockwise to open. Remove key.

3. Coolant Fill door is unlocked in the same manner. It can

be used for adding coolant or oil.

To close access door:

1. Close door and turn door’s handle one quarter

turn clockwise.

2. Insert key into lock of door handle and turn key one

quarter turn clockwise. Remove key.

The Gaseous Fuel System

The information below is provided to assist gaseous fuel

system technicians in planning installations. In no way

should this information be interpreted to conflict with

applicable fuel gas codes. Consult with your local fuel

supplier or Fire Marshall if questions or problems arise.

TO THE INSTALLER: Consult with the generator owner(s)

and convey any technical considerations that might

affect their installation plans before applying these

general guidelines.

The following general rules apply to gaseous fuel

system piping:

 • Thepipingshouldbeofamaterialthatconformsto

federal and local codes, rigidly mounted and protected

against vibration.

 • Pipingshouldbeprotectedfromphysicaldamage

where it passes through flower beds, shrub beds, and

other cultivated areas where damage could occur.

B

A

C

D

E

WARNING Contact with muffler and engine parts can

result in serious burns.

DO NOT touch hot parts and AVOID hot exhaust gases.•

Allow equipment to cool before touching.•

WARNING Propane and Natural Gas are extremely

flammable and explosive.

Fire or explosion can cause severe burns

or death.

LP gas is heavier than air and will settle in low areas.•

Natural gas is lighter than air and will collect in •

high areas.

The slightest spark can ignite these fuels and cause •

an explosion.

DO NOT light a cigarette or smoke.•

11

 • Installtheflexible,gaseoushose(supplied)between

the generator fuel inlet port and rigid piping to prevent

thermal expansion or contraction from causing

excessive stress on the piping material.

NOTE: Where local conditions include earthquake, tornado,

unstable ground, or flood hazards, special consideration

shall be given to increase strength and flexibility of piping

supports and connections.

 • Pipingmustbeofthecorrectsizetomaintainthe

required supply pressures and volume flow under

varying generator load conditions with all gas

appliances connected to the fuel system turned on

and operating.

 • Useapipesealantorjointcompoundapprovedfor

use with NG/LPG on all threaded fittings to reduce the

possibility of leakage.

 • Installedpipingmustbeproperlypurgedand

leak tested, in accordance with applicable codes

and standards.

Consider the following factors when planning to install the

fuel supply system:

 • Airdensityislessathighaltitudes,resultinginless

available engine power. See Power Decrease at High

Altitude or High Temperature in the operator’s manual.

 • Aminimumofoneaccessible,approvedmanualshutoff

valve shall be installed in the fuel supply line within 6 ft

(1.8 m) of the residential generator. A union or flanged

connection shall be provided downstream from this

valve to permit removal of controls.

 • BothLPvaporandnaturalgasfuelsupplypressure

at the generator’s fuel inlet port should be between

7 to 11 inches of water (in. W.C.) at full load with all

gas appliances turned on and operating.

The generator unit has been factory load tested to run on

either natural gas or LP vapor fuel. The unit can be converted

from natural gas to LP vapor or vice versa using two people

and special tools. See Fuel Conversion, later in this manual.

It is recommended that the fuel connection incorporate the

following components:

 • Aminimum10ft.(3m)sectionofgaspipebetween

the primary fuel regulator and the generator fuel inlet

connection (acts as accumulator for high block loads).

 • Amanualfuelshut-offvalvelocatedintheinteriorof

the building.

 • Amanualfuelshut-offvalvelocatedoutsidethe

building, just before the generator unit.

 • Wheretheformationofhydratesoriceisknownto

occur, piping should be protected against freezing. The

termination of hard piping should include a sediment

trap where condensate is not likely to freeze.

 • Amanometerportshouldbeprovided.

CAUTION The supplied flexible gaseous pipe is not to

be installed underground or in contact with the ground.

The entire flexible gaseous pipe must be visible for •

periodic inspection and must not be concealed within nor

contact nor run through any wall, floor, or partition.

WARNING Propane and Natural Gas are extremely

flammable and explosive.

Fire or explosion can cause severe

burns or death.

Before placing the generator into service, the fuel system •

lines must be properly purged and leak tested.

No leakage is permitted.•

12

The manometer port permits temporary installation of

a manometer to ensure that the engine receives the

correct fuel pressure to operate efficiently throughout its

operating range.

When the initial test runs are completed, the manometer

is removed and the port is plugged. A typical final fuel

connection assembly is shown here, where (A) is the fuel

supply and (B) goes to the generator.

Fuel Pipe Sizing

There are numerous on-line or otherwise-published

references for fuel pipe sizing. For example, NFPA 54 -

National Fuel Gas Code, 2006 (Item #: 320-6031-06) is a

common resource. The installer should consider the specific

gravity of gas and compensate for a nominal amount of

restriction from bends, fittings, etc. If an unusual number of

fittings, bends, or other restrictions are used, refer to federal

and local codes for guidance.

Fuel Consumption

Estimated fuel supply requirements at half and full load for

natural gas and LP vapor fuels are shown below.

Natural Gas LP Vapor

1/2 Load Full Load 1/2 Load Full Load

483 C 777 C 178 C 297 C

483,000 B 777,000 B 445,000 B 742,000 B

C = Cubic feet per hour

B = BTU’s per hour

Physical Properties LP Vapor Natural

Gas

Normal Atmospheric State Gas Gas

Boiling Point (in °F):

Initial

End

-44

-259

Heating Value:

BTU per gallon (Net LHV*)

BTU per gallon (gross**)

Cubic feet (gas)

83,340

91,547

2,500

63,310

1,000

Density*** 36.39 57.75

Weight† 4.24 2.65

Octane Number:

Research

Motor

110+

97

110+

* LHV (Low Heat Value) is the more realistic rating.

** Gross heat value does not consider heat lost in the form of water

during combustion.

*** Densityisgivenin“CubicFeetofGasperGallonofLiquid”.

† Weightisgivenin“PoundsperGallonofLiquid”.

B

A

13

System Connectors

Low voltage connections to signal fault contacts, transfer switch communication, remote LED and auxiliary 12VDC power are

made via a removable ten-pole connector plug. Compare this illustration with your generator to familiarize yourself with the

location of these connections. Count down to the proper pin location on the control board since visual alignment with the

decal can be misleading:

A - 10 Pole Connector Plug

B - Fault Contacts — Use NO, COM and NC to hook up a

siren, light, etc. to alert you in case of a fault. Contacts

reverse state (NO goes to NC and vice versa) upon a

fault condition.

C - Transfer Switch Communication — Connect to transfer

switch control board for communication interface using

18AWG copper twisted pair wire.

D - Remote LED Output — Use this to hook up the remote

LED supplied with the generator. The remote LED will

turn on and off in a series of blinks if certain faults are

detected in the generator.

E - +12 Volt DC, .5 Amp Output — Internal auxiliary

power supply.

C

B

A

D

E

IMPORTANT:

•For45kWpoweroutputconnection,use#3/0AWGminimum300volt75°C-90°Ccopperwire,(ref.NECTable310.16,

100 ft. Use National Electric Code for correction factors and wire size calculations.)

•ForUtilityCircuitconnectionuse#14AWGminimum300volt75°C-90°Ccopperwire.

•Fortransferswitchcommunicationuse#18AWGtwistedpairconductors,nogreaterthan200ftinlength,300volt

75°C-90°C copper wire.

•Fastenonlyonewiretoeachconnectorscrew.

•Torqueconnectorplugscrewsto7in-lb(7.9Newtonmeter).

14

Generator AC Connection System

A single-phase, three-wire AC connection system is used

in the residential generator. The stator assembly consists

of a pair of stationary windings with two leads brought out

of each winding. The junction of leads T2 and T3 forms the

neutral lead, as shown schematically and as wiring diagram

below. A complete schematic and wiring diagram can be

found later in this manual.

NOTE: Neutral is not bonded to ground at generator.

Grounding the Generator

Ground the generator per applicable codes, standards and

regulations. There are two generator GND lug locations.

The one inside the alternator junction box next to the circuit

breaker is the primary lug and should suffice for most

applications. The second generator GND lug is located on the

frame below the generator circuit breaker cover and should

ONLY be used for a ground rod located at the generator, if

required by local codes. See Controls for location.

Utility Circuit Connection

“240VUtilityCircuit”leadsmustberoutedinconduit.The

“240VUtilityCircuit”leadsdeliverpowertothegenerator’s

circuit board and water heater. This power also charges

the starting battery. When power on these leads is lost, the

generator will start.

Using installer-supplied minimum 300V, 14 AWG copper

wire, connect each ten-amp fuse terminal in the alternator

junction box to the ten-amp fuse terminals in the automatic

transfer switch.

When making connections, obey wire type and torque

specifications printed on the circuit breaker and neutral/

ground connector.

Fault Detection System

The generator may have to run for long periods of time with

no operator present. For that reason, the system is equipped

with sensors that automatically shut down the generator

in the event of potentially damaging conditions, such as

low oil pressure, high temperature, over speed, and other

conditions. Refer to Fault Detection System in the Operator’s

Manual for more detailed information.

The owner will use the remote LED indicator to observe the

status of the residential generator system. The remote LED

will turn on and off in a series of blinks if certain faults are

detected in the generator system. Consult with the owner

for a convenient location. Locate the electrical box in an

area visible by the home owner such as near a garage door

opener or security control panel.

To install the remote LED indicator:

1. Push the LED through the mounting plate from the

front until it snaps in place.

IMPORTANT: The LED is polarity sensitive.

2. Using provided 10 pole connector and installer-supplied

minimum 18AWG wire, connect the remote LED to the

generator control board +LED and GND connection.

Use wire nuts to attach wire to LED leads.

3. Attach mounting plate to installer-supplied

electrical box.

10 A

240 VAC

T2

120 V

240 V

T4

T1

T3

N

G

T4

T1

Neutral

To Transfer Switch

Control

Board

Ground

Power Winding

Circuit

Breaker

Line 1

Water

Heater

Neutral

To Transfer Switch

Utility Fuse

Connection

Line 2

Ground

15

System Control Panel

The residential generator control panel, located inside the

generator housing, is shown below.

Brief descriptions of the controls used during installation are:

A - Circuit Breaker — Must be ON to supply power to the

transfer switch. Breaker enclosure includes removable

bottom panel to assist with conduit connections.

B - SET EXERCISE — Used to set exercise cycle start time.

C - MANUAL OVER-RIDE — Used to manually start and stop

the generator.

D - 15 Amp Fuse — Protects DC control circuits.

E - System Switch — Switches modes to OFF or AUTO.

F - Digital Display — Displays running time in hours or

fault codes.

See Controls in the operator’s manual for more information

System Switch

This two-position switch is the most important control on

the residential generator and is used as follows:

 • “AUTO”positionisthenormaloperatingposition.If

a utility power outage is sensed, the system will start

the generator. When utility power is restored, lets the

engine stabilize internal temperatures, shuts off the

generator, and waits for the next utility power outage.

 • “OFF”positionturnsoffrunninggenerator,prevents

unit from starting and resets any detected faults.

15 Amp Fuse

Protects the generator DC control circuits. If the fuse has

‘blown’ (melted open) or was removed, the engine cannot

crank or start. Replace the fuse using only an identical

ATO 15A fuse. One spare fuse is supplied with the unit.

If fuse was blown or removed, you will need to reset the

exercise timer (see Setting Exercise Timer).

Final Installation Considerations

Engine Oil

The engine is shipped from the factory pre-run and filled

with non-synthetic oil (API SL 10W-30). This allows for

system operation in a wide range of temperature and climate

conditions. Before starting the engine, check oil level and

ensure that engine is serviced as described in the engine

operator’s manual.

Coolant System

The engine is shipped from the factory filled with a

50-50 mix of automotive (Dex-Cool™ orange) anti-freeze

and water. This will provide optimum year round protection

against freezing, boiling and corrosion. The coolant system

incorporates a water heater that operates when ambient

temperature is below 80ºF AND utility power is present at the

transfer switch. Periodically check coolant level as described

in the engine manual.

A

B

C

E

D

F

NOTICE Any attempt to crank or start the engine before

it has been properly serviced with the recommended

coolant or oil will result in equipment failure.

Refer to • Maintenance in the operator’s manual and engine

manual for coolant and oil fill information.

Damage to equipment resulting from failure to follow this •

instruction will void engine and generator warranty.

16

Battery

The installer must supply and install a valve-regulated

rechargeable starting battery. The starting battery MUST

conform to the specifications shown in this chart.

Battery Specifications

Volts 12 Volt DC

Amps (MIN) 650 CCA (cold cranking amps)

Type Valve Regulated Lead Acid (VRLA)

Terminal Hardware Post

Dimensions (MAX):

Width 7.5 inches (191mm)

Length 11.25 inches (286mm)

Height 10.0 inches (254mm)

Install the battery as described in Servicing the Battery in

the Maintenance section of the operator’s manual. Always

make sure the NEGATIVE cable is connected last.

Fuel Supply System

Ensure that all fuel pipe connections are tight, secure and

without leaks.

Ensure that all gas line shutoff valves are OPEN and that

adequate fuel pressure is available whenever automatic

operation is desired.

Initial Start-up (No Load)

Before operating the generator or placing it into service,

inspect the entire installation carefully. Then begin testing the

system without any electrical loads connected, as follows:

NOTE: Unit has been set-up for NG or LP vapor operation at

the factory. Fuel conversion, if needed, must be completed

prior to performing these steps.

1. Connect an accurate AC voltmeter and a frequency

meter to check generator output at load side of

circuit breaker.

2. Set generator’s circuit breaker to its ON

(closed) position.

3. Confirm 15 Amp fuse is installed in system

control panel.

4. Set generator’s system switch to AUTO.

5. Push and hold MANUAL OVER-RIDE button on control

panel for about six seconds. Engine will start.

NOTE: When the generator is started for the very first time, it

will require that air in the gaseous fuel lines be purged. This

may take a few minutes.

6. Listen for unusual noises, vibration or other indications

of abnormal operation. Check for oil or coolant leaks

while engine runs.

7. Let engine warm up for about five minutes to allow

internal temperatures to stabilize.

8. No-load voltage should be 239 - 244 Volts, frequency

should be 59.8 - 60.2 Hz.

NOTE: If AC voltage is outside these ranges, perform the

generator adjustment, Steps 11 and 12 below.

9. Check generator output between one of the generator

connection lugs and the neutral lug, then between the

other generator connection lug and the neutral lug. In

both cases, voltage reading should be 117 - 123 Volts.

IMPORTANT: DO NOT proceed until you are certain that

generator AC voltage is correct and within the stated limits.

Generator frequency is fixed and not adjustable.

10. If voltage and frequency values are correct, proceed to

step 13.

11. Connect voltmeter as described in step 1 above.

12. While observing voltmeter, adjust alternator voltage

control (A) for 240 volts. DO NOT adjust either of the

other alternator controls.

13. Push and hold MANUAL OVER-RIDE button on control

panel until engine stops.

14. Install alternator circuit breaker enclosure cover.

UNDER-FREQ.

ADJUST

STABILITY

ADJUST

VOLTAGE

ADJUST

A

WARNING Battery posts, terminals and related

accessories contain lead and lead compounds - chemicals

known to the State of California to cause cancer and

reproductive harm. Wash hands after handling.

17

Test Shutdown(s) Procedure

The installer will test the system to verify that diagnostic

messages are correctly shown on the system control panel

digital display, as follows:

FC_1 - Low Battery

No test procedure required for this fault.

FC_2 - Low Oil Pressure

Locate wire #85 (A) connected to the oil pressure switch.

Connect an installer-supplied jumper wire to wire #85.

With the system switch in AUTO position, push and hold

MANUAL OVER-RIDE to start the generator. With the

generator running, connect other end of jumper to a good

ground location such as the engine block. The generator will

shut down and FC_2 will be displayed on the system control

panel. Remove the jumper wire. Turn the system switch to

OFF for 30 seconds to clear the fault.

FC_3 - Low Voltage

With the system switch in AUTO position, push and hold

MANUAL OVER-RIDE to start the generator. With the

generator running at no load, turn the generator circuit

breaker to OFF. The generator should shut down and

FC_3 will be displayed on the system control panel. Turn the

system switch to OFF for 30 seconds to clear the fault. Turn

the circuit breaker to ON position.

FC_4 - Engine Fails to Start

With the generator not running, turn the installer supplied

manual fuel valve to the OFF position. With the system

switch in AUTO, turn off utility power. The engine will crank,

attempting to start. After approximately a two-minute start

attempt (10 seconds of crank, 10 seconds of rest) the

generator should terminate the start attempt and FC_4 will

be displayed on the system control panel. Turn the system

switch to OFF for 30 seconds to clear the fault. Turn the

installer supplied fuel valve to the ON position.

FC_5 - Low Frequency

No test procedure required for this fault.

FC_6 - Engine Overspeed

No test procedure required for this fault.

FC_7 - High Temperature

Locate wire #95 (B) connected to the temperature switch.

Connect an installer-supplied jumper wire to wire #95.

With the system switch in AUTO position, push and hold

MANUAL OVER-RIDE to start the generator. With the

generator running, connect other end of jumper to a good

ground location such as the engine block. The generator

should shut down and display FC_7 on the system control

panel. Remove the jumper wire. Turn the system switch to

OFF for 30 seconds to clear the fault.

FC_8 - Transfer Switch Fault

(Units with ACCM II or later transfer switch only)

Verify that utility power is present at the automatic transfer

switch. With the system switch in AUTO position, carefully

remove one of the 2 Amp fuses from the transfer switch.

FC_8 will display on the system control panel. Carefully

reinstall the fuse in the transfer switch, then turn the system

switch to OFF for 30 seconds to clear the fault.

Analyze Test Results

If any test procedure above does not cause the generator

to shut down and display the indicated fault, repair the fault

condition before putting the unit into service.

A

B

18

Fuel Conversion

The unit is shipped from the factory calibrated for NG or LP

vapor operation. To convert the engine from NG to LP vapor

or from LP vapor to NG operation, follow these steps:

1. Set generator circuit breaker to OFF.

2. Set control panel system switch to OFF.

3. Remove 15 Amp fuse from system control panel.

4. Remove Zero Pressure Regulator (ZPR) tower cap (A).

The Main Adjust control is shown as (B).

5. Calibrate O

2

sensor per Analyzer manufacturer

specification. Install O

2

sensor into exhaust pipe.

NOTE: Technician supplies O

2

sensor and analyzer.

6. Attach timing light to #1 spark plug on engine (see

engine manual for diagram).

7, Re-install 15 Amp fuse in system control panel.

8. Set generator circuit breaker to ON.

9. Set control panel System switch to AUTO.

10. After purging fuel supply line, push and hold

MANUAL OVER-RIDE button on control panel for six

seconds. When engine starts, allow unit to warm up for

ten minutes under no load.

NOTE: If utility power is not connected, the generator

will start automatically.

11. Using technician-supplied timing light, locate timing

marks on crankshaft vibration dampener.

12. If timing is not within specification, loosen distributor

hold-down clamp. While observing timing indicator,

adjust distributor as listed below:

LP = 24 degrees before top dead center at no load

NG = 32 degrees before top dead center at no load

NOTE: Timing values are approved by PSI engineering.

13. Tighten distributor hold-down clamp.

14. While observing O

2

Analyzer readout, adjust zero

pressure regulator (A) and main adjustment (B) screws

to obtain stoichiometric value shown in table. Select

table value that corresponds to your O

2

Analyzer

display. The shaded line in table indicates optimum

target value.

Voltage Phi Lamda

2.40 1.000 1.000

2.45 1.012 0.988

2.50 1.024 0.977

2.55 1.036 0.966

2.60 1.048 0.955

2.65 1.060 0.944

2.70 1.071 0.933

15. Using technician-supplied load, add half load to

generator. Check and adjust (A) and (B) to achieve

target value.

16. Using technician-supplied load, add full load to

generator. Check and adjust (A) and (B) to achieve

target value.

17. Remove load and check if sensor value remained in

target area. If needed, adjust (A) and (B) to achieve

target value.

18. Add half, then full load to generator. Recheck and verify

sensor value remains in target area.

IMPORTANT: It may take several attempts to achieve the

target setting. Continue to test and adjust with engine

stabilized at no, half and full loads until target value is

achieved at all generator loads.

19. Remove load from generator. Allow generator to run

for ten minutes to stabilize internal temperatures. Turn

control panel system switch to OFF.

20. Remove 15 Amp fuse from system control panel.

21. Install the ZPR tower cap, remove O

2

sensor, and

timing light.

22. Re-install 15 Amp fuse in system control panel.

23. Set exercise timer.

24. Complete emissions statement and send with

installation checklist.

B A

WARNING Contact with muffler and engine parts can

result in serious burns.

DO NOT touch hot parts and AVOID hot exhaust gases.•

Allow equipment to cool before touching.•

19

Reserved

20

Schematic Diagram

La page est en cours de chargement...

Simplicity 076003LP- Guide d'installation

Ce manuel convient également à

Simplicity 076003LP- Guide d'installation

dans d''autres langues

Documents connexes