Maytag MSB26C6MDM00 Guide d'installation

Marque: Maytag

Modèle: MSB26C6MDM00

Catégorie: Frigos

Taper: Guide d'installation

Ce manuel convient également à

INSTALLATIONINSTRUCTIONSAND OWNER'S MANUAL

Do Not Throw Away -- Additional important safety information included.

Para las instruccionos on ospa_ol, uisito nuostro s/rio do intomot.

INSTRUCTIONSD'INSTALLATIONETMANUEL D'UTILISATION

Ne pas jeter -- Autres consignes de s_curit_ importantes ci-jointes.

Table of Contents / Tabledes mati@res

REFRIGERATOR SAFETY ..................................................................... 2

Proper Disposal of Your Old Refrigerator ........................................... 3

INSTALLATION INSTRUCTIONS ......................................................... 3

Unpack the Refrigerator ...................................................................... 3

Door Removal, Leveling and Alignment ............................................. 4

Handle Installation and Removal ........................................................ 7

Location Requirements ....................................................................... 8

Electrical Requirements ...................................................................... 8

Water Supply Requirements ............................................................... 8

Connect Water Supply ........................................................................ 9

Install Air Filter ................................................................................... 11

Install Produce Preserver .................................................................. 12

Changing the Water Filter ................................................................. 13

REFRIGERATOR CARE ....................................................................... 13

Cleaning ............................................................................................ 13

Lights ................................................................................................. 14

Vacation and Moving Care ............................................................... 15

PROBLEM SOLVER ............................................................................. 16

WATER FILTER CERTIFICATIONS .................................................... 20

PERFORMANCE DATA SHEET .......................................................... 21

SI_CURITI_ DU RI_FRIGI_RATEUR ..................................................... 22

Mise au rebut appropriee de votre vieux refrigerateur ..................... 23

INSTRUCTIONS D'INSTALLATION ................................................... 23

Deballage du refrigerateur ................................................................ 23

Retrait, reglage de I'aplomb et alignement des portes .................... 24

Installation et demontage des poignees .......................................... 27

Exigences d'emplacement ............................................................... 28

Specifications electriques ................................................................. 28

Specifications de I'alimentation en eau ............................................ 29

Raccordement de la canalisation d'eau ........................................... 29

Installation du filtre &air .................................................................... 31

Installation du sachet de conservation pour produits frais .............. 32

Changer le filtre &eau ....................................................................... 33

ENTRETIEN DU RI_FRIGI_RATEUR ................................................... 34

Nettoyage .......................................................................................... 34

Lampes ............................................................................................. 34

Entretien avant les vacances ou Iors d'un demenagement ............. 36

RI_SOLUTION DE PROBLI_MES ........................................................ 37

FEUlLLE DE DONNI£'ES SUR LA PERFORMANCE .......................... 43

W10631232B

REFRIGERATORSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

[] Plug into a grounded 3 prong outlet.

[] Do not remove ground prong.

[] Do not use an adapter.

[] Do not use an extension cord.

[] Disconnect power before servicing.

[] Replace all parts and panels before operating.

[] Remove doors from your old refrigerator.

[] Use nonflammable cleaner.

[] Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

[] Use two or more people to move and install refrigerator.

[] Disconnect power before installing ice maker (on ice maker

kit ready models only).

[] Use a sturdy glass when dispensing ice (on some models).

[] Do not hit the refrigerator glass doors (on some models).

SAVE THESE INSTRUCTIONS

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

ProperDisposalofYourOld Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

Before You Throw Away Your Old Refrigerator or Freezer:

• Takeoff the doors.

• Leave the shelves in place so that children may not easily

climb inside.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous,

even if they will sit for "just a few days." Ifyou are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

important information to know about disposal of

refrigerants:

Dispose of refrigerator in accordance with Federal and Local

regulations. Refrigerants must be evacuated by a licensed,

EPA certified refrigerant technician in accordance with

established procedures.

INSTALLATIONINSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with

cardboard or hardboard to avoid floor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or

"walk" the refrigerator when trying to move it, as floor

damage could occur.

Remove packaging materials. Do not use sharp instruments,

rubbing alcohol, flammable fluids, or abrasive cleaners to remove

tape or glue. These products can damage the surface of your

refrigerator. For more information, see "Refrigerator Safety."

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

Gathertherequiredtoolsandpartsandreadallinstructionsbeforestartinginstallation.Savetheseinstructionsforfuturereference.

IMPORTANT:Thegraphicsonthispageareformodelswiththeicestoragebinonthedoor.Onmodelswiththeicestoragebininside

thefreezer,thewiringandwaterdispensertubingconfigurationsaresimplerthanwhatisshowninthesegraphics.Pleasereadall

instructionsonthenextfewpagesformoreinformation.

NOTE:Beforemovingyourproductintoyourhome,measurethedoorwayofyourhometoseewhetheryouneedtoremovethe

refrigeratorandfreezerdoors.Ifdoorremovalisnecessary,seetheinstructionsbelow.

IMPORTANT:Beforeyoubegin,turntherefrigeratorcontrolOFForturncoolingoff.Unplugrefrigeratorordisconnectpower.Remove

food,theicestoragebin(onsomemodels),andanyadjustabledoororutilitybinsfromdoors.

__ Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Wiring Connection

A B C D E F

A, P-clamp D. Wiring Clip

B. Routing E. Grommets

Plate F. Wiring

C. Electrical Plugs

Housing

Water Dispenser

Tubing Connection

(Style 1)

A, Face of Fitting

Top Left Hinge

A. Do Not Remove Screws.

Water Dispenser Tubing

Connection (Style 2)

Door Removal

Base Grille

Top Right Hinge

A. Do Not Remove Screws.

Bottom Hinges

(Left and Right)

Leveling

A, Bottom Hinge

B. Leveler Bracket

C. Leveling Foot

Door Alignment

(Bottom Right Hinge)

_Lower 4 =_ _ "

Raise

A.Alignment Screw

TOOLSNEEDED:

Bubblelevel,Phillipsscrewdriver,3/le"hexkey,1/4"hex-head

socketwrench,1/4"and%e"open-endedwrenchesoradjustable

wrench,internalstardriveor3/8"hex-headsocketwrench

Remove the Doors

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Unplug refrigerator or disconnect power.

Open both doors to 90°. Remove the base grille by removing

the two screws, then pulling out on the outside corners. See

Graphic 1.

NOTE: The doors must only be opened to 90°. If they are

opened all the way, the base grille will not come off.

Disconnect the water tubing, located behind the base grille on

the freezer door side. The dispenser tubing runs through the

door hinge, and must be disconnected in order to remove the

door.

NOTE: On models with the ice storage bin on the door, there

are two water tubing connections, as shown. On models with

the ice storage bin inside the freezer, there is only one water

tubing connection.

• Style 1: Press the colored outer ring against the face of

fitting and pull the water tubing free. See Graphic 2A.

NOTE: Keep the water tubing connector attached to the

tube that runs underneath the freezer. The door cannot be

removed if the connector is still attached to the tube that

runs through the door hinge.

Style 2: Firmly pull on the clasp to release the tube, then

pull the water tubing free. See Graphic 2B.

NOTE: Keep the clasp attached to the tube that runs

underneath the freezer.

Disconnect the wiring, located behind the base grille on the

freezer door side. See Graphic 3.

On models with the ice storage bin on the door:

NOTE: There are two wiring bundles that run underneath the

freezer - a large bundle with a large grommet and two white

plugs at the end, and a small bundle with a small grommet

and one yellow plug at the end.

• Remove the P-clamp using a 1/4"hex-head socket wrench.

Remove the small wiring bundle from the P-clamp.

• Remove the wiring clip using a 1/4"hex-head socket

wrench.

• Pull the electrical housing out from under the refrigerator.

Disconnect the wiring plugs from the housing.

• Gently pull the large wiring bundle (with two white plugs)

through the routing plate.

On models with the ice storage bin inside the freezer:

NOTE: The wiring configuration is simpler than what is shown

in Graphic 3. There is only one wiring bundle with one wiring

plug, and there is not a routing plate.

• Remove the wiring clip using a 1/4"hex-head socket

wrench.

• Pull the electrical housing out from under the refrigerator.

Disconnect the wiring plug from the housing.

Close both doors and keep them closed until you are ready to

lift them free from the cabinet.

Use a 3/le"hex key to remove the top left hinge screws as

shown. See Graphic 4.

IMPORTANT: Do not remove either screw A.

Excessive Weight Hazard

Use two or more people to lift the freezer door.

Failure to do so can result in back or other injury.

10.

Lift freezer door straight up off bottom hinge. See Graphic 5.

The water tubing and wiring remain attached to the freezer

door and pull through the bottom left hinge.

NOTE: This may require two people - one to lift the door and

another to feed the water tubing and wiring through the hinge.

On models with the ice storage bin on the door:

Be sure the hole in the hinge is clear of obstructions, then

gently pull one water tube through the hinge. (Avoid

kinking the tube.) Next, gently pull the other water tube

through the hinge, again avoiding kinks. Finally, gently pull

the wiring bundle (including the grommet and wiring plugs)

through the hinge.

models with the ice storage bin inside the freezer:

Be sure the hole in the hinge is clear of obstructions, then

gently pull the water tube through the hinge. (Avoid kinking

the tube.) Next, gently pull the wiring bundle (including the

grommet and wiring plug) through the hinge.

IMPORTANT: Rest the door on its side on a soft, clean

surface, such as a towel, blanket or piece of cardboard. This

will help avoid damaging the door, water tubing and wiring.

Use a 3/le"hex key to remove the top right hinge screws as

shown. See Graphic 6.

IMPORTANT: Do not remove either screw A.

Lift the refrigerator door straight up off bottom hinge.

IMPORTANT: Rest the door on its side on a soft, clean

surface, such as a towel, blanket or piece of cardboard. This

will help avoid damaging the door.

It may not be necessary to remove the bottom hinges to move

the refrigerator through a doorway. Both bottom hinges have

similar construction.

• If necessary, use an internal star drive or a 3/8"hex-head

socket wrench to remove the bottom hinges. See

Graphic 7.

IMPORTANT: The leveler brackets are mounted behind

the hinges. If you remove the hinges, make sure that the

leveler brackets are replaced when reinstalling the hinges.

Replace the Doors and Hinges

1. Replace both bottom hinges, if removed. Make sure that the

leveler brackets are assembled behind the hinges. Tighten

screws.

IMPORTANT: When the screws are tightened properly, there

should not be any gaps between the refrigerator, leveler

bracket and hinge.

ExcessiveWeightHazard

Usetwoor more people to lift the freezer door.

Failure to do so can result in back or other injury.

Before replacing the freezer door on the bottom left hinge,

feed the wiring and water tubing through the hinge.

On models with the ice storage bin on the door:

• Feed the small wiring bundle through the hinge.

Assistance may be needed.

IMPORTANT: Do not feed the large wiring bundle through

the hinge. This bundle is intended to run directly from the

door to the connections beneath the freezer. Forcing the

large bundle through the hinge may damage the door

and/or the wiring, and will keep the door from closing

properly.

Feed both water tubes through the bottom left hinge, then

replace the freezer door on the hinge. Assistance may be

needed.

On models with the ice storage bin inside the freezer:

• Feed the wiring bundle through the hinge. Assistance may

be needed.

• Feed the water tube through the bottom left hinge, then

replace the freezer door on the hinge. Assistance may be

needed.

NOTE: Provide additional support for the doors while the top

hinges are being replaced. Do not depend on the door magnets to

hold the doors in place while you are working.

3. Align and replace the top left hinge as shown. See Graphic 4.

Tighten screws.

4. Reconnect water tubing and wiring.

IMPORTANT: Do not intertwine the water tubing and wiring

bundles when reconnecting them.

On models with the ice storage bin on the door:

Water Connection Style 1: Push the larger %e" (7.94 mm)

water tube into the blue fitting until it stops, then push the

smaller 1/4"(6.35 ram) water tube into the green fitting until

it stops. See Graphic 2A.

Water Connection Style 2: Push the black water tube

with the blue tip into the blue fitting until it stops. Close

the clasp around the tubing, making sure it snaps into

place. Repeat this process to connect the red-tipped

black water tube and the red fitting. See Graphic 2B.

Reinstall the P-clamp around the small wiring bundle (with

one yellow plug), then replace the P-clamp on the top

screw hole of the routing plate. See Graphic 3.

Gently route the large wiring bundle (with two white plugs)

through the hole in the routing plate, so that the wiring

runs behind the right side of the routing plate. See

Graphic 3.

NOTE: The large wiring bundle should always remain

below the small wiring bundle.

Reconnect the wiring plugs to the electrical housing, then

push the housing back under the refrigerator. Align the left

hole in the front lip of the housing with the right hole in the

refrigerator's base crossbar. See Graphic 3.

Reinstall the wiring clip over the grommets. First install the

smaller grommet into the top of the clip, then install the

larger grommet into the bottom of the clip (closest to the

screw hole). See Graphic 3.

Align the clip's screw hole with the left hole in the electrical

housing and the right hole in the crossbar, and screw in

the clip using a single screw. Tighten screw. See

Graphic 3.

IMPORTANT: Once connected, the wiring bundles should

not be taut. Some flexibility is needed to allow the freezer

door to open properly.

models with the ice storage bin inside the freezer:

• Water Connection Style 1: Push the water tube into the

fitting until it stops. See Graphic 2A.

Water Connection Style 2: Push the water tube into the

fitting until it stops. Close the clasp around the tubing,

making sure it snaps into place. See Graphic 2B.

Reconnect the wiring plug to the electrical housing, then

push the housing back under the refrigerator. Align the left

hole inthe front lip of the housing with the right hole in the

refrigerator's base crossbar. See Graphic 3.

• Reinstall the wiring clip over the grommet. See Graphic 3.

Align the clip's screw hole with the left hole in the electrical

housing and the right hole in the crossbar, and screw in

the clip using a single screw. Tighten screw. See

Graphic 3.

IMPORTANT: Once connected, the wiring should not be

taut. Some flexibility is needed to allow the freezer door to

open properly.

5. Replace the refrigerator door by lifting the door onto the

bottom right hinge.

6. Align and replace the top right hinge as shown. See Graphic 6.

Tighten screws.

7. Replace the ice storage bin (on some models) and any

adjustable door or utility bins.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

8. Plug refrigerator into a grounded3 prong outlet.

Leveling and Door Closing

Your refrigerator has two adjustable front feet -- one on the right

and one on the left. In most cases, the refrigerator should be

steady when both feet are touching the floor. Ifyour refrigerator

seems unsteady or if you want the doors to close more easily,

adjust the refrigerator's tilt using the instructions below:

1. Move the refrigerator into its final location. If necessary, open

both doors to 90° and remove the base grille. See Graphic 1.

2. The two leveling feet are located on the brackets on each side

of the product. See Graphic 8.

NOTE: Having someone push against the top of the refrigerator

takes some weight off the leveling feet. This makes it easier to

make adjustments.

Use a 1/4"open-ended or adjustable wrench to adjust the

leveling feet. Turn the leveling foot to the left to raise that side

of the product, or turn it to the right to lower that side of the

product.

NOTE: Both leveling feet should be snug against the floor, and

the rollers should not touch the floor. This keeps the

refrigerator from rolling forward when opening the doors.

Open both doors again and check that they close as easily as

you like. If not, tilt the refrigerator slightly more to the rear by

turning the leveling feet to the left. It may take several more

turns, and you should turn both leveling feet the same

amount.

5. Use a bubble level to check the leveling of the refrigerator.

NOTE: Whenever you need to move the refrigerator, turn the

leveling feet to the right until they are no longer touching the

ground. This will allow the refrigerator to roll more easily.

Door Alignment

A refrigerator that is not level from side-to-side may appear to

have doors that are not properly aligned. If the doors appear this

way, use the instructions in the previous section to check the

leveling.

The doors are designed to be slightly different heights when the

refrigerator is empty, in order to account for the weight of food

that will be placed on the doors. If the doors are still not aligned

after checking the leveling and loading the refrigerator with food,

follow the steps below to adjust the door alignment.

1. If necessary, open both doors to 90° and remove the base

grille. See Graphic 1.

2. Locate the alignment screw on the bottom hinge of the

refrigerator door. See Graphic 9.

3. Use as/16"open-ended or adjustable wrench to turn the screw.

To raise the refrigerator door, turn the screw to the right. To

lower the door, turn the screw to the left.

4. Check that the doors are even at the top. If necessary,

continue to turn the alignment screw until the doors are

aligned.

5. Open both doors to 90°. Replace the base grille. See

Graphic 1.

PARTS INCLUDED: Door handles (2), 1/s"hex key, spare

setscrew(s)

To Install the Handles:

NOTE: The handle mounting setscrews are preinstalled in the

handle.

1. Remove the handles, which are packed inside the refrigerator.

NOTE: To avoid scratching the finish, place the handles on a

towel or other soft surface.

Open the freezer door. On the refrigerator door, place the

handle on the shoulder screws with the setscrews facing the

freezer.

A. Shoulder screws

B. Setscrews inside the handle

3. Firmly push the handle toward the door until the handle base

is flush against the door.

4. While holding the handle, insert the short end of the hex key

into the upper hole and slightly rotate the hex key until it is

engaged in the setscrew.

Using a clockwise motion, tighten the setscrew until it begins

to contact the shoulder screw.

Repeat steps 4 and 5 to begin fastening the lower setscrew.

Once both setscrews have been partially tightened as outlined

in the previous steps, fully tighten both the upper and lower

setscrews.

IMPORTANT: When the screws feel tight, tighten them an

additional quarter-turn. The handle is not properly installed

without this extra tightening.

Open the refrigerator door and close the freezer door. Repeat

steps 2 through 7 to install the other handle onto the freezer

door with the setscrews facing the refrigerator.

Save the hex key and all instructions.

Remove the Handles:

While holding the handle, insert the short end of the hex key

into the lower setscrew hole and slightly rotate the hex key

until it is engaged in the setscrew.

Using a counterclockwise motion, loosen the setscrew a

quarter-turn at a time.

Repeat steps 1 and 2 for the upper setscrew. Gently pull the

handle away from the door.

If necessary, use a Phillips screwdriver to remove the shoulder

screws from the door.

!!equ emen, ts

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT: This refrigerator is designed for indoor household

use only.

To ensure proper ventilation for your refrigerator, allow for V2"

(1.27 cm) of space on each side and at the top. Allow for 1"

(2.54 cm) of space behind the refrigerator. If your refrigerator has

an ice maker, allow extra space at the back for the water line

connections. When installing your refrigerator next to a fixed wall,

leave a 2" (5.08 cm) minimum space on each side (depending on

your model) to allow the doors to swing open.

V2" (1.27

2" (5.08 cm)

NOTES:

This refrigerator is intended for use in a location where the

temperature ranges from a minimum of 55°F (13°C) to a

maximum of 110°F (43°C). The preferred room temperature

range for optimum performance, which reduces electricity

usage and provides superior cooling, is between 60°F (15°C)

and 90°F (32°C). It is recommended that you do not install the

refrigerator near a heat source, such as an oven or radiator.

Normal minimum cabinet cut-out width required for product

installation is 36" (91.44 cm). However, if the product is placed

against an extended wall and the ability to remove the crisper

pans is desired, an additional 18" (45.72 cm) of cabinet width

is required, so a total cabinet opening width of 54"

(137.16 cm)is recommended.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 volt, 60 Hz, AC only, 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

NOTE: Before performing any type of installation or cleaning, or

removing a light bulb, turn cooling off or turn the control

(Thermostat, Refrigerator or Freezer Control depending on the

model) to OFF, and then disconnect the refrigerator from the

electrical source. When you are finished, reconnect the

refrigerator to the electrical source and turn cooling on or reset the

control (Thermostat, Refrigerator or Freezer Control depending on

the model) to the desired setting. See "Using the Controls" in the

User Instructions, User Guide, or Use & Care Guide.

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

TOOLS NEEDED:

• Flat-blade screwdriver • V4"nut driver

• 7Ae"and V_"open-end or • %" drill bit

two adjustable wrenches • Cordless drill

NOTE: Your refrigerator dealer has a kit available with a V4"

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.

Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or 3Ae"

(4.76 mm) saddle valve which reduces water flow and clogs more

easily.

IMPORTANT:

• All installations must meet local plumbing code requirements.

• Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

Water Pressure

A cold water supply with water pressure of between 30 and

120 psi (207 and 827 kPa) is required to operate the water

dispenser and ice maker. Ifyou have questions about your water

pressure, call a licensed, qualified plumber.

• If your refrigerator has a water dispenser: After installation is

complete, use the water dispenser to check the water

pressure.

With the water filter removed, dispense 1 cup (237 mL) of

water. If 1 cup of water is dispensed in 8 seconds or less,

the water pressure to the refrigerator meets the minimum

requirement.

• If it takes longer than 8 seconds to dispense 1 cup of

water, the water pressure to the refrigerator is lower than

recommended. See "Problem Solver" for suggestions.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 30 and 120 psi (207 and

827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

If your refrigerator has a water filter, it may further reduce the

water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See "Water Filtration

System" in the User Instructions, User Guide, or Use & Care

Guide.

If you have questions about your water pressure, call a licensed,

qualified plumber.

++,J,OF/" @0 f_,: @_'

Read all directions before you begin.

IM PORTANT:

• Plumbing shall be installed in accordance with the

International Plumbing Code and any local codes and

ordinances.

The gray water tubing on the back of the refrigerator (which is

used to connect to the household water line) is a PEX

(cross-linked polyethylene) tube. Copper and PEX tubing

connections from the household water line to the refrigerator

are acceptable, and will help avoid oft-taste or odor in your ice

or water. Check for leaks.

If PEX tubing is used instead of copper, we recommend the

following Whirlpool Part Numbers:

W10505928RP (7 ft [2.14 m] jacketed PEX),

8212547RP (5 ft [1.52 m] PEX), or

W10267701RP (25 ft [7.62 m] PEX).

• Install tubing only in areas where temperatures will remain

above freezing.

TOOLS NEEDED:

Gather the required tools and parts before starting installation.

• Flat-blade screwdriver

• 7/le"and 1/2"open-end wrenches or two adjustable wrenches

• 1/4"nut driver

Connect to Water Line

IMPORTANT: Ifyou turn the refrigerator on before the water line is

connected, turn the ice maker OFE

Style 1 (Recommended)

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Use a quarter-turn shutoff valve or the equivalent, served by a

1/2"copper household supply line.

NOTE: To allow sufficient water flow to the refrigerator, a

minimum 1/2"size copper household supply line is

recommended.

A. Bulb

B. Nut

I/ l

C. Copper tubing (to refrigerator)

D. Household supply fine (Y2"minimum)

Now you are ready to connect the copper tubing to the shutoff

valve. Use 1/4"(6.35 mm) OD soft copper tubing to connect the

shutoff valve and the refrigerator.

• Ensure that you have the proper length needed for the job.

Be sure both ends of the copper tubing are cut square.

Slip compression sleeve and compression nut onto

copper tubing as shown. Insert end of tubing into outlet

end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not

overtighten.

A. Compression sleeve

B. Compression nut

C. Copper tubing

Place the free end of the tubing into a container or sink, and

turn on main water supply to flush out tubing until water is

clear. Turn off shutoff valve on the water pipe.

NOTE: Always drain the water line before making the final

connection to the inlet of the water valve, to avoid possible

water valve malfunction.

Bend the copper tubing to meet the water line inlet, which is

located on the back of the refrigerator cabinet as shown.

Leave a coil of copper tubing to allow the refrigerator to be

pulled out of the cabinet or away from the wall for service.

Style 2

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Locate a 1/2"(1.27 cm) to 11/4"(3.18 cm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from

the drill and normal sediment from collecting inthe valve.

4. Determine the length of copper tubing you need. Measure

from the connection on the lower rear corner of refrigerator to

the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4"

(6.35 mm) O.D. (outside diameter) copper tubing. Be sure both

ends of copper tubing are cut square.

5. Using a cordless drill, drill a 1/4"(6.35 mm) hole in the cold

water pipe you have selected.

A. Cold water pipe

B. Pipe clamp

C. Copper tubing

D. Compression nut

E. Compression sleeve

E Shutoff valve

G. Packing nut

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the 1/4"(6.35 mm)

drilled hole in the water pipe and that the washer is under the

pipe clamp. Tighten the packing nut. Tighten the pipe clamp

screws slowly and evenly so the washer makes a watertight

seal. Do not overtighten, or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw the compression

nut onto outlet end with adjustable wrench. Do not

overtighten.

8. Place the free end of the tubing in a container or sink, and turn

ON the main water supply. Flush the tubing until water is clear.

Turn OFF the shutoff valve on the water pipe. Coil the copper

tubing.

Connect to Refrigerator

Style 1

1. Unplug refrigerator or disconnect power.

2. Remove and discard the short, black plastic part from the end

of the water line inlet.

Thread the nut onto the end of the tubing. Tighten the nut by

hand. Then tighten it with a wrench two more turns. Do not

overtighten.

NOTE: To avoid rattling, be sure the copper tubing does not

touch the cabinet's side wall or other parts inside the cabinet.

A B C

A. Household water line

B. Nut (purchased)

C. Ferrule (purchased)

D. Refrigerator water tubing

Install the water supply tube clamp around the water supply

line to reduce strain on the coupling.

Turn shutoff valve ON.

Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the plastic part that is attached to the

inlet of the water valve.

Attach the copper tube to the valve inlet using a compression

nut and sleeve as shown. Tighten the compression nut. Do not

overtighten.

Use the tube clamp on the back of the refrigerator to secure

the tubing to the refrigerator as shown. This will help avoid

damage to the tubing when the refrigerator is pushed back

against the wall.

Turn shutoff valve ON.

Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

__ A

_.....................B

.........................D

..... E

A. Tubeclamp D. Compressionnut

B. Tubeclamp screw E.Valveinlet

C.Copper tubing

On some models, the ice maker is equipped with a built-in

water strainer. If your water conditions require a second water

strainer, install it in the 1/4"(6.35 mm) water line at either tube

connection. Obtain a water strainer from your nearest

appliance dealer.

Style 3

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray water

tube on the rear of the refrigerator.

3. If the gray water tube supplied with the refrigerator is not long

enough, a V4"x 1/4"(6.35 mm x 6.35 mm) coupling is needed in

order to connect the water tubing to an existing household

water line. Thread the provided nut onto the coupling on the

end of the copper tubing.

NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

A B C

A. Refrigerator water tubing

B. Nut (provided)

C. Bulb

D. Coupling (purchased)

D E F G

E. Ferrule (purchased)

E Nut (purchased)

G. Household water line

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

Complete the Installation

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See "Water and Ice Dispensers" in the

User Instructions or User Guide.

NOTE: Allow 24 hours to produce the first batch of ice. Allow

72 hours to completely fill ice container.

(o_} some modes}

On some models, your refrigerator's accessory packet includes

an air filter, which must be installed prior to use. On some models,

the air filter is already installed at the factory.

The air filter reduces the buildup of odors. This helps to maintain a

cleaner environment inside the refrigerator.

Installing the Air Filter (on some models)

The filter should be installed behind the vented door, which is

located (depending on your model) along either the rear or left

interior wall near the top of the refrigerator compartment.

1. Remove the air filter from its packaging.

2. Lift open the vented door.

3. Snap the filter into place.

4. Close the vented door.

Installing the Filter Status Indicator (on some models)

The filter comes with a status indicator, which should be activated

and installed at the same time the air filter is installed.

1. Place the indicator face-down on a firm, flat surface.

2. Apply pressure to the bubble on the back of the indicator, until

the bubble pops to activate the indicator.

3. Lift open the vented air filter door. On some models, there are

notches behind the door.

4. On models with notches:

• Slide the indicator down into the notches, facing outward.

NOTE: The indicator will not easily slide into the notches

if the rear bubble has not been popped.

Close the air filter door, and check that the indicator is

visible through the rectangular hole in the door.

On models without notches:

• Store the indicator in a visible place you will easily

remember - either inside the refrigerator, or elsewhere in

your kitchen or home.

Replacing the Air Filter

The disposable air filter should be replaced every 6 months, when

the status indicator has completely changed from white to red.

To order a replacement air filter, see "Accessories" in the User

Instructions or User Guide.

1. Remove the old air filter by squeezing in on the side tabs.

2. Remove the old status indicator.

3. Install the new air filter and status indicator using the

instructions in the previous sections.

(o_"_some modes}

On some models, your refrigeratoCs accessory packet includes a

Produce Preserver, which should be installed prior to use. On

some models, the Produce Preserver is already installed at the

factory.

The Produce Preserver absorbs ethylene, allowing the ripening

process of many produce items to slow down. As a result, certain

produce items will stay fresh longer.

Ethylene production and sensitivity varies depending on the type

of fruit or vegetable. To preserve freshness, it is best to separate

produce with sensitivity to ethylene from fruits that produce

moderate to high amounts of ethylene.

Apples

Asparagus

Berries

Broccoli

Cantaloupe

Sensitivity to

Ethylene

High

Med.

Low

High

Med.

Carrots Low Very Low

Citrus Fruit Med. Very Low

Grapes Low Very Low

Lettuce High Very Low

Pears High Very High

Spinach High Very Low

Installing the Produce Preserver (on some models)

Ethylene

Production

Very High

Very Low

Low

Very Low

High

The Produce Preserver pouches should be installed in their

housing, which is located along an interior side wall of the crisper

or convertible drawer.

NOTE: For best performance, always use two pouches.

1. Remove the Produce Preserver pouches from their packaging.

2. Lift up on the housing in order to remove it from its mounting

tab along the wall.

3. Open the housing by pulling up and out on the back of the top

of the housing.

4. Place both pouches inside the housing, then snap the housing

back together.

5. Place the housing back on the mounting tab along the wall.

Installing the Status Indicator (on some models)

The Produce Preserver comes with a status indicator, which

should be activated and installed at the same time the pouch is

installed.

CAUTION: IRRITANT

MAY IRRITATE EYES AND SKIN. DANGEROUS FUMES

FORM WHEN MIXED WITH OTHER PRODUCTS.

Do not mix with cleaning products containing ammonia,

bleach or acids. Do not get in eyes, on skin or clothing. Do

not breathe dust. Keep out of reach of children.

FIRST AID TREATMENT: Contains potassium

permanganate. If swallowed, call a Poison Control Center or

doctor immediately. Do not induce vomiting. If in eyes, rinse

with water for 15 minutes. If on skin, rinse with water.

1. Place the indicator face-down on a firm, flat surface.

2. Apply pressure to the bubble on the back of the indicator, until

the bubble pops to activate the indicator.

3. Slide open the cap on the Produce Preserver housing.

4. Place the indicator in the top of the housing, facing outward.

5. Slide the cap closed, and check that the indicator is visible

through the rectangular hole in the cap.

NOTE: The cap will not easily close if the indicator's rear

bubble has not been popped.

Replacing the Produce Preserver (on some models)

The disposable pouches should be replaced every 6 months,

when the status indicator has completely changed from white to

red.

To order replacements, see "Accessories" in the User Instructions

or User Guide.

1. Remove the old pouches from the Produce Preserver housing.

2. Remove the old status indicator.

3. Install the new pouches and status indicator using the

instructions in the previous sections.

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

The water filter status light will help you know when to change

your water filter. See "Water Filtration System" in the User

Instructions or User Guide.

NOTE: If water flow to your water dispenser or ice maker

decreases noticeably, change the filter sooner. The filter should be

replaced at least every 6 months, depending on your water quality

and usage.

1. Locate the water filter in the top-right corner of the refrigerator

compartment.

2. Lift open the filter cover door. The filter will be released and

then be ejected as the door is opened.

3. When the door is completely open, pull the filter straight out.

NOTE: There may be some water in the filter. Some spilling

may occur. Use a towel to wipe up any spills.

Take the new filter out of its packaging and remove the cap.

Be sure the O-rings are still in place after the cap is removed.

[]

A. Cap B. O-rings

5. With the arrow pointing up, align the new filter with the filter

housing and slide it into place. The filter cover door will

automatically begin to close as the new filter is inserted.

6. Close the filter cover door completely in order to snap the filter

into place. You may need to press hard.

7. After changing the filter, reset the filter status light. See "Water

Filtration System" in the User Instructions or User Guide.

8. Flush the water system. See "Water and Ice Dispensers" in the

User Instructions or User Guide.

REFRIGERATORCARE

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to avoid

buildup of odors. Wipe up spills immediately.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid odor

transfer and drying out of food, wrap or cover foods tightly.

To Clean Your Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning waxes,

concentrated detergents, bleaches or cleansers containing

petroleum products on plastic parts, interior and door liners or

gaskets. Do not use paper towels, scouring pads, or other harsh

cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

3. Wash stainless steel and painted metal exteriors with a clean

sponge or soft cloth and a mild detergent in warm water.

4. There is no need for routine condenser cleaning in normal

home operating environments. If the environment is

particularly greasy or dusty, or there is significant pet traffic in

the home, the condenser should be cleaned every 2 to

3 months to ensure maximum efficiency.

If you need to clean the condenser:

Remove the base grille. See the "Door Removal"

instructions, either in the User Instructions or the

Installation Instructions and Owner's Manual, or in the

separate instruction sheet provided with your refrigerator.

• Use a vacuum cleaner with a soft brush to clean the grille,

the open areas behind the grille and the front surface area

of the condenser.

• Replace the base grille when finished.

5. Plug in refrigerator or reconnect power.

IMPORTANT: The light bulbs in both the refrigerator and freezer

compartments of your new refrigerator may use LED technology.

If the lights do not illuminate when the refrigerator and/or freezer

door is opened, call for assistance or service. In the U.S.A., call

1-800-253-1301. In Canada, call 1-800-807-6777.

Light Styles:

The dispenser lights are mini LEDs that cannot be changed.

The interior lights vary by model.

• Some models have mini LEDs that cannot be changed.

• Some models have full-size LED bulbs that can be

changed. To order replacement LED bulbs, call

1-800-253-1301 (U.S.A.) or 1-800-807-6777 (Canada).

Whirlpool

Part Number

W10574850A

(2.0 watts)

Whirlpool

Part Number

W10565137A

(3.6 watts)

NOTE: Some LED replacement bulbs are not

recommended for wet/damp environments. The

refrigerator and freezer compartments are considered to

be wet/damp environments. If using a brand of LED bulb

other than the recommended Whirlpool LED bulb, read

and follow all instructions on the replacement bulb's

packaging before installing it.

Some models have incandescent 40-watt bulbs that can

be changed.

Refrigerator Compartment - Upper Lights

Light Shield Removal:

• Slide the light shield toward the rear of the refrigerator and

remove it from the light housing.

Replacement Bulb:

• If the burned-out light is afull-size LED bulb, replace it with

Whirlpool part number W10574850A (a 2.0 watt LED bulb).

• If the burned-out light is an incandescent bulb, replace it with

an incandescent appliance bulb of the same size, shape and

wattage (40-watt maximum).

Light Shield Reinstallation:

• Align the light shield in the grooves at the bottom edge of the

light housing, then slide it forward until it snaps into place.

NOTE: Not all replacement bulbs will fit your refrigerator.

Do not use an incandescent bulb in excess of 40 watts.

To Change a Light Bulb:

1. Unplug refrigerator or disconnect power.

2. Remove the light shield, as explained in the following

sections.

NOTE: To clean the light shield, wash it with warm water and

liquid detergent. Before reinstalling, thoroughly rinse and dry

the shield.

Replace the burned-out light bulb, as explained in the

following sections.

Reinstall the light shield, as explained in the following

sections.

Plug in refrigerator or reconnect power.

Refrigerator Compartment - Lower Lights

Light Shield Removal:

• Slide the light shield to the right to remove the left end from

the wall slots, then pull the right end out of its wall slots.

Replacement Bulb:

• If the burned-out light is afull-size LED bulb, replace it with

Whirlpool part number W10565137A (a 3.6 watt LED bulb).

• If the burned-out light is an incandescent bulb, replace it with

an incandescent appliance bulb of the same size, shape and

wattage (40-watt maximum).

Light Shield Reinstallation:

• Place the right end of the light shield into the wall slots, then

snap the left end into its wall slots.

Freezer Compartment - Upper Light

Light Shield Removal:

• Gently squeeze the front and the bottom-rear edge of the light

shield to release the tabs from the wall slots, then pull the light

shield forward.

Replacement Bulb:

• If the burned-out light is a full-size LED bulb, replace it with

Whirlpool part number W10565137A (a 3.6 watt LED bulb).

• If the burned-out light is an incandescent bulb, replace it with

an incandescent appliance bulb of the same size, shape and

wattage (40-watt maximum).

Light Shield Reinstallation:

• Align the light shield in its proper position, and snap the tabs

into the wall slots.

Freezer Compartment - Lower Light

Light Shield Removal:

• Slide the light shield to the left to remove the right end from

the wall slots, then pull the left end out of its wall slots.

Replacement Bulb:

• If the burned-out light is afull-size LED bulb, replace it with

Whirlpool part number W10565137A (a 3.6 watt LED bulb).

• If the burned-out light is an incandescent bulb, replace it with

an incandescent appliance bulb of the same size, shape and

wattage (40-watt maximum).

Light Shield Reinstallation:

• Place the left end of the light shield into the wall slots, then

snap the right end into its wall slots.

Vacations

If You Choose to Leave Refrigerator On While You Are Away:

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker and is

connected to the household water supply, turn off the water

supply to the refrigerator. Property damage can occur if the

water supply is not turned off.

3. If you have an automatic ice maker, turn off the ice maker.

NOTE: Depending on your model, raise the wire shutoff arm to

OFF (up) position or press the switch to OFF (right).

4. Empty the ice bin.

If You Choose to Turn Refrigerator Off Before You Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or move the switch to the OFF

(right) setting.

3. Depending on the model, turn the Refrigerator Control to OFF

or turn cooling off. See "Using the Controls" in the User

Instructions, User Guide, or Use & Care Guide.

4. Clean, wipe, and dry thoroughly.

5. Tape rubber or wood blocks to the tops of both doors to prop

them open far enough for air to get in. This stops odor and

mold from building up.

Moving

When you are moving your refrigerator to a new home, follow

these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• Disconnect the water line from the back of the refrigerator.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or move the switch to the OFF

(right) setting.

Remove all food from the refrigerator and pack all frozen food

in dry ice.

Empty the ice bin.

4. Depending on the model, turn the Refrigerator Control to OFF

or turn cooling off. See "Using the Controls" in the User

Instructions, User Guide, or Use & Care Guide.

5. Unplug refrigerator.

6. Clean, wipe, and dry thoroughly.

7. Take out all removable parts, wrap them well, and tape them

together so they don't shift and rattle during the move.

8. Depending on the model, raise the front of the refrigerator so it

rolls more easily OR screw in the leveling legs so they don't

scrape the floor. See "Adjust the Doors" or "Door Removal,

Leveling and Alignment."

9. Tape the doors closed and tape the power cord to the back of

the refrigerator.

When you get to your new home, put everything back and refer to

the Installation Instructions for preparation instructions. Also, if

your refrigerator has an automatic ice maker, remember to

reconnect the water supply to the refrigerator.

PROBLEMSOLVER

First try the solutions suggested here or visit our website to possibly avoid the cost of a service call.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

GENERAL OPERATION Possible Causes and/or Recommended Solutions

Refrigerator

will not operate

Not connected to an electrical supply - Plug the power cord into a grounded 3 prong outlet.

Do not use an extension cord.

• No power to the electrical outlet - Plug in a lamp to see if the outlet is working.

• Household fuse has blown or circuit breaker has tripped - Replace the fuse or reset the circuit

breaker. If the problem continues, contact a licensed electrician.

• Control or cooling is not turned on - Turn on the refrigerator control, or turn cooling on.

See "Using the Controls" in the User Instructions or User Guide.

• New installation - Following installation, allow 24 hours for the refrigerator and freezer to cool

completely.

NOTE: Adjusting the temperature control(s) to the coldest setting will not cool either

compartment (refrigerator or freezer) more quickly.

Motor seems to

run too much

Your new refrigerator has an energy-efficient motor - The refrigerator may run longer than

you're used to, because the compressor and fans operate at lower speeds that are more

energy-efficient. This is normal.

NOTE: Your refrigerator may run even longer if the room is warm, a large load of food is added,

the doors are opened often, or if a door has been left open.

GENERAL OPERATION Possible Causes and/or Recommended Solutions

Refrigerator seems noisy The compressor inyour new refrigerator regulates temperature more efficiently and uses less energy

than older models. During various stages of operation, you may hear normal operating sounds that

are unfamiliar.

The following noises are normal:

• Buzzing/Clicking - Heard when the water valve opens and closes to dispense water or fill the ice

maker. If the refrigerator is connected to a water line, this is normal. If the refrigerator is not

connected to a water line, turn off the ice maker.

• Cracking/Crashing - Heard when ice is ejected from the ice maker mold.

• Popping - Heard when the inside walls contract/expand, especially during initial cooldown.

• Pulsating/Whirring - Heard when the fans/compressor adjust to optimize performance during

normal operation.

• Rattling - Heard when water passes through the water line, or due to the flow of refrigerant.

Rattling may also come from items placed on top of the refrigerator.

• Water running or gurgling - Heard when ice melts during the defrost cycle and water runs into

the drain pan.

• Sizzling - Heard when water drips onto the heater during the defrost cycle.

Temperature is too warm New installation - Following installation, allow 24 hours for the refrigerator and freezer to cool

completely.

NOTE: Adjusting the temperature control(s) to the coldest setting will not cool either

compartment (refrigerator or freezer) more quickly.

Doors are opened often or not closed completely - This allows warm air to enter the

refrigerator. Minimize door openings, keep the doors fully closed, and make sure both doors are

properly sealed.

Air vents are blocked - Remove items that are immediately in front of the vents.

Large amount of warm food recently added - Allow several hours for the refrigerator to return

to its normal temperature.

Controls are not set correctly for the surrounding conditions - Adjust the controls to a colder

setting. Check the temperature again in 24 hours.

Temperature is too cold Controls are not set correctly for the surrounding conditions - Adjust the controls to a

warmer setting. Check the temperature again in 24 hours.

Top refrigerator shelf is colder than lower shelves - On some models, air from the freezer

enters the refrigerator compartment through vents near the top refrigerator shelf. As a result, the

top shelf can be slightly colder than lower shelves.

• Air vents are blocked - Remove items that are immediately in front of the vents.

Interior moisture buildup NOTE: Some moisture buildup is normal. Clean with a soft dry cloth.

• Room is humid - A humid environment contributes to moisture buildup. Use the refrigerator only

in an indoor location, with as little humidity as possible.

• Doors are opened often or not closed completely - This allows humid air to enter the

refrigerator. Minimize door openings, keep the doors fully closed, and make sure both doors are

properly sealed.

Interior lights do not work • Doors have been open for an extended period of time - Close the doors to reset the lights.

• Light bulb is loose in the socket or has burned out - On models with incandescent or full-size

LED interior light bulbs, tighten or replace the bulb. See "Lights."

NOTE: On models with mini LED lights, call for assistance or service if the interior lights do not

illuminate when either door is opened. See the Warranty in the User Instructions or User Guide for

contact information.

Dispenser lights

do not work

(on some models)

Dispenser light is turned off - On some models, if the dispenser light is set to OFF, the light will

turn on only when a dispenser pad/lever is pressed. If you want the dispenser light to stay on

continuously, select adifferent setting. See "Water and Ice Dispensers" in the User Instructions or

User Guide.

• Dispenser light is set to AUTO or NIGHT LIGHT - On some models, if the dispenser light is set

to AUTO or NIGHT LIGHT, make sure the dispenser light sensor is not blocked. See "Water and

Ice Dispensers" in the User Instructions or User Guide.

NOTE: On models with mini LED lights, call for assistance or service if the dispenser lights do not

operate correctly. See the Warranty in the User Instructions or User Guide for contact information.

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

DOORS AND LEVELING Possible Causes and/or Recommended Solutions

Doors are difficult to open • Gaskets are dirty or sticky - Clean the gaskets and contact surfaces with mild soap and warm

water. Rinse and dry with a soft cloth.

Doors will not • Door is blocked open - Move food packages away from the door. Make sure all bins and

close completely shelves are in their correct positions. Make sure all packaging materials have been removed.

Doors appear to be uneven • Doors need to be aligned, or refrigerator needs to be leveled - See the leveling and door

alignment instructions.

Refrigerator rocks • Refrigerator is not level - To stabilize the refrigerator, remove the base grille and lower the

and is not stable leveling feet until they touch the floor. See the leveling and door alignment instructions.

Cut Hazard

Use a sturdy glass when dispensing ice.

Failure to do so can result in cuts.

ICE AND WATER Possible Causes and/or Recommended Solutions

Ice maker is not •

producing ice,

not producing

enough ice,

or producing

small/hollow ice

Refrigerator is not connected to a water supply, or the water supply shutoff valve is not fully

turned on - Connect the refrigerator to a water supply and make sure the water shutoff valve is

fully open.

Kink in the water source line - A kink in the water line can reduce water flow, resulting in decreased ice

production, small ice cubes, and/or hollow or irregularly-shaped ice. Straighten the water line.

Ice maker is not turned on - Turn on the ice maker. See "Ice Maker and Storage Bin" in the User

Instructions or User Guide.

New installation - After connecting the refrigerator to a water source, flush the water system.

(See "Water and Ice Dispensers" in the User Instructions or User Guide.) Wait 24 hours for ice

production to begin. Wait 72 hours for full ice production. Discard the first three batches of ice produced.

Large amount of ice was recently removed - Allow sufficient time for the ice maker to produce

more ice.

• Ice is jammed in the ice maker ejector arm - Remove ice from the ejector arm using a plastic utensil.

• Inadequate water pressure - Verify that the household has adequate water pressure. See "Water

Supply Requirements."

• Water filter is installed incorrectly - Make sure the filter is properly installed. See "Water Filtration

System" in the User Instructions or User Guide.

• A reverse osmosis water filtration system is connected to your cold water supply - This can

decrease water pressure. See "Water Supply Requirements."

NOTE: If questions remain regarding water pressure, contact a licensed, qualified plumber.

ICE AND WATER Possible Causes and/or Recommended Solutions

Ice dispenser •

will not operate

properly •

Doors not closed completely - Make sure both doors are firmly closed. (On some modems,only the

freezer door must be closed in order to operate the dispenser.)

New installation - After connecting the refrigerator to a water source, flush the water system.

(See "Water and Ice Dispensers" in the User Instructions or User Guide.) Wait 24 hours for ice

production to begin. Wait 72 hours for full ice production. Discard the first three batches of ice produced.

Ice maker is not turned on, or ice bin is not installed correctly - Turn on the ice maker and make sure

the ice storage bin is firmly in position. See "Ice Maker and Storage Bin" in the User Instructions or User

Guide.

Ice is clogged or frozen together in the ice storage bin, or ice is blocking the ice delivery

chute - Remove or separate the clogged ice, using a plastic utensil if necessary. Clean the ice delivery

chute and the bottom of the ice storage bin using awarm damp cloth, then dry both thoroughly. To avoid

clogging and to maintain a fresh supply of ice, empty the storage bin and clean both the storage bin and

the delivery chute every 2 weeks.

Wrong ice has been added to the storage bin - Use only ice cubes produced by the current ice maker.

Dispenser is locked - Unlock the dispenser. See "Water and Ice Dispensers" in the User Instructions or

User Guide.

Ice dispenser jams while dispensing crushed ice - For models with the ice storage bin on the door,

temporarily switch from crushed ice to cubed ice to clear the jam.

Dispenser pad/lever has been pressed too long - Ice will automatically stop dispensing. Wait a few

minutes for the dispenser to reset, then resume dispensing. Take large amounts of ice directly from the

ice bin, not through the dispenser.

Water pressure to the home is not at or above 30 psi (207 kPa) - The water pressure to the home

affects the flow from the dispenser. See "Water Supply Requirements."

Water filter is clogged or incorrectly installed - Replace filter or reinstall it correctly. See "Water

Filtration System" in the User Instructions or User Guide.

Ice or water has an

off-taste, odor,

or gray color

New plumbing connections - New plumbing connections can result in off-flavored or discolored ice or

water. This problem should go away over time.

Ice has been stored too long - Discard the ice and wash the ice bin. Allow 24 hours for the ice maker to

produce new ice.

Odor has transferred from food - Use airtight moisture-proof packaging to store food.

Use of non-recommended water supply line - Odors and tastes can transfer from certain materials

used in non-recommended water supply lines. Use only a recommended water supply line. See "Water

Supply Requirements."

There are minerals (such as sulfur) in the water - A water filter may need to be installed in order to

remove the minerals.

Water filter was recently installed or replaced - Gray or dark discoloration in ice or water indicates

that the water filtration system needs additional flushing. See "Water and Ice Dispensers" in the User

Instructions or User Guide.

Water dispenser

will not operate

properly

Doors not closed completely - Make sure both doors are firmly closed. (On some models, only the

freezer door must be closed in order to operate the dispenser.)

Refrigerator is not connected to a water supply, or the water supply shutoff valve is not

turned on - Connect the refrigerator to a water supply and make sure the water shutoff valve is

fully open.

Kink in the water source line - A kink in the water line can reduce water flow to the dispenser.

Straighten the water line.

Water pressure to the home is not at or above 30 psi (207 kPa) - The water pressure to the home

affects the flow from the dispenser. See "Water Supply Requirements."

New installation - After connecting the refrigerator to a water source, flush the water system.

See "Water and Ice Dispensers" in the User Instructions or User Guide.

Dispenser is locked - Unlock the dispenser. See "Water and Ice Dispensers" in the User Instructions or

User Guide.

• Water filter is clogged or incorrectly installed - Replace filter or reinstall it correctly. See "Water

Filtration System" in the User Instructions or User Guide.

• A reverse osmosis water filtration system is connected to your cold water supply - This can

decrease water pressure. See "Water Supply Requirements."

NOTE: If questions remain regarding water pressure, contact a licensed, qualified plumber.

ICE AND WATER Possible Causes and/or Recommended Solutions

Water is leaking or

dripping from the

dispenser

NOTE: After dispensing, a few additional drops of water are normal.

• Glass was not held under the dispenser long enough - Hold the glass under the dispenser for

2 to 3 seconds after releasing the dispenser pad/lever.

• New installation, or water filter was recently installed or replaced - Air inthe water lines causes the

water dispenser to drip. Flush the water system to remove the air in the water lines. See "Water and Ice

Dispensers" in the User Instructions or User Guide.

• Residual ice in the dispenser chute is melting - Make sure the ice chute is free of ice shavings or

pieces.

Water is leaking • Water line connections are not fully tightened - Make sure all connections are firmly tightened. See

from the back of the "Connect Water Supply."

refrigerator

Water from the

dispenser is

not cool enough

(on some models)

NOTE: Water from the dispenser is chilled to 50°F (10°C).

• New installation - Allow 24 hours after installation for the water supply to cool completely.

• Recently dispensed a large amount of water - Allow 24 hours for the new water supply to cool

completely.

• Water has not been recently dispensed - The first glass of water may not be cool. Discard the first

glass of water dispensed.

• Refrigerator is not connected to a cold water pipe - Make sure the refrigerator is connected to a cold

water pipe. See "Water Supply Requirements."

WATERFILTERCERTIFICATIONS

State of Calitomia

Department of Public Health

WaterTreatmentDevice

CertificateNumber

10-2030

Date Issued: February 26, 201(}

Re_lacemenl Elements

P4R_'WB

Cysts

Organic Contatili_ant_

&trazme

Rated Service Capacity.": 200 gal Rated Service FIow: 0,5 gpm

Conditions of Cer tifit'ation:

i)o no_ use wberc water Js microNologically unsafe or wi_h water of unknown quality, excep_ that syslems certified

for cyst reduction may be used on disinfected waters that nl3y contain filterabIe cysts.

La page est en cours de chargement...

Maytag MSB26C6MDM00 Guide d'installation

Marque: Maytag

Modèle: MSB26C6MDM00

Catégorie: Frigos

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag MSB26C6MDM00 Installation guide

Maytag MSB26C6MDM00 Guide d'installation

Ce manuel convient également à

Maytag MSB26C6MDM00 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents