Zanussi ZWS76100WW Manuel utilisateur

Catégorie
Machines à laver
Taper
Manuel utilisateur
GETTING
STARTED?
EASY.
User Manual
ZWS76100WW
EN User Manual 2
Washing Machine
FR Notice d'utilisation 20
Lave-linge
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible for any
injuries or damage that are the result of incorrect installation or
usage. Always keep the instructions in a safe and accessible
location for future reference.
CHILDREN AND VULNERABLE PEOPLE SAFETY
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning the use of the
appliance in a safe way and understand the hazards involved.
Children between 3 and 8 years of age and persons with very
extensive and complex disabilities shall be kept away from the
appliance unless continuously supervised.
Children of less than 3 years of age should be kept away from
the appliance unless continuously supervised.
Do not let children play with the appliance.
Keep all packaging away from children and dispose of it
appropriately.
Keep detergents away from children.
Keep children and pets away from the appliance when the door
is open.
Children shall not carry out cleaning and user maintenance of
the appliance without supervision.
GENERAL SAFETY
Do not change the specification of this appliance.
This appliance is intended to be used in household and similar
applications such as:
staff kitchen areas in shops, offices and other working
environments;
by clients in hotels, motels, bed & breakfast and other
residential type environments;
areas for communal use in blocks of flats or in launderettes.
2
Do not exceed the maximum load of 7 kg (refer to the
"Programme chart" chapter).
The operating water pressure at the water entry point from the
outlet connection must be between 0.5 bar (0.05 MPa) and 8
bar (0.8 MPa).
The ventilation opening in the base must not be covered by a
carpet, mat, or any floor covering.
The appliance must be connected to the water mains using the
new supplied hose sets, or other new hose sets supplied by
the Authorised Service Centre.
Old hose sets must not be reused.
If the mains power supply cable is damaged, it must be
replaced by the manufacturer, its Authorised Service Centre or
similarly qualified persons to avoid an electrical hazard.
Before any maintenance operation, deactivate the appliance
and disconnect the mains plug from the socket.
Do not use high pressure water sprays and/or steam to clean
the appliance.
Clean the appliance with a moist cloth. Use only neutral
detergents. Do not use abrasive products, abrasive cleaning
pads, solvents or metal objects.
SAFETY INSTRUCTIONS
INSTALLATION
The installation must comply with
relevant national regulations.
Remove all the packaging and the transit bolts
including rubber bush with plastic spacer.
Keep the transit bolts in a safe place. If the
appliance is to be moved in the future they must
be reattached to lock the drum to prevent an
internal damage.
Always take care when moving the appliance as
it is heavy. Always use safety gloves and
enclosed footwear.
Follow the installation instructions supplied with
the appliance.
Do not install or use a damaged appliance.
Do not install or use the appliance where the
temperature can be less than 0°C or where it is
exposed to the weather.
The floor area on which the appliance is to be
installed must be flat, stable, heat resistant and
clean.
Make sure that there is air circulation between
the appliance and the floor.
When the appliance is in its permanent position,
check if it is levelled correctly with the aid of a
spirit level. If it is not, adjust the feet accordingly.
Do not install the appliance directly above a
floor drain.
Do not spray water on the appliance and do not
expose it to excessive humidity.
Do not install the appliance where the appliance
door cannot be fully opened.
Do not put a closed container to collect
possible water leakage under the appliance.
Contact the Authorised Service Centre to
ensure which accessories can be used.
3
ELECTRICAL CONNECTION
WARNING! Risk of fire and electric
shock.
The appliance must be earthed.
Always use a correctly installed shockproof
socket.
Make sure that the parameters on the rating
plate are compatible with the electrical ratings
of the mains power supply.
Do not use multi-plug adapters and extension
cables.
Make sure not to cause damage to the mains
plug and to the mains cable. Should the mains
cable need to be replaced, this must be carried
out by our Authorised Service Centre.
Connect the mains plug to the mains socket
only at the end of the installation. Make sure that
there is access to the mains plug after the
installation.
Do not touch the mains cable or the mains plug
with wet hands.
Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
WATER CONNECTION
Do not cause damage to the water hoses.
Before connection to new pipes, pipes not used
for a long time, where repair work has been
carried out or new devices fitted (water meters,
etc.), let the water flow until it is clean and clear.
Ensure that there are no visible water leaks
during and after the first use of the appliance.
Do not use an extension hose if the inlet hose is
too short. Contact the Authorised Service
Centre for the replacement of the inlet hose.
When unpacking the appliance, It is possible to
see water flowing from the drain hose. This is
due to the testing of the appliance with the use
of water in the factory.
You can extend the drain hose to maximum 400
cm. Contact the Authorised Service Centre for
the other drain hose and the extension.
Make sure that there is access to the tap after
the installation.
USE
WARNING! Risk of injury, electric
shock, fire, burns or damage to the
appliance.
Follow the safety instructions on the detergent
packaging.
Do not put flammable products or items that are
wet with flammable products in, near or on the
appliance.
Do not wash fabrics which are heavily soiled
with oil, grease or other greasy substances. It
can damage rubber parts of the washing
machine. Prewash such fabrics by hand before
loading them into the washing machine.
Do not touch the glass door while a programme
operates. The glass can get hot.
Make sure that all metal objects are removed
from the laundry.
SERVICE
To repair the appliance contact the Authorised
Service Centre.
Use original spare parts only.
DISPOSAL
WARNING! Risk of injury or
suffocation.
Disconnect the appliance from the mains
electrical and water supplies.
Cut off the mains electrical cable close to the
appliance and dispose of it.
Remove the door catch to prevent children or
pets from becoming trapped in the drum.
Dispose of the appliance in accordance with
local requirements for the disposal of Waste
Electrical and Electronic Equipment (WEEE).
4
PRODUCT DESCRIPTION
APPLIANCE OVERVIEW
1
2
3
5
6
7
4
1
Worktop
2
Detergent dispenser
3
Control panel
4
Rating plate
5
Door handle
6
Drain pump filter
7
Feet for levelling the appliance
CONTROL PANEL
CONTROL PANEL DESCRIPTION
31 2
5 467
1
Programme knob
2
Départ différé - Delay Start button
3
Programme phase indicators:
Washing phase ( )
Extra rinse phase ( )
End of cycle ( )
4
Départ/Pause - Start/Pause button
5
Rapide - Quick button
6
Essorage - Spin reduction option: Automatic
and Rinse Hold
5
7
Temp. button
PROGRAMMES
PROGRAMME CHART
Programme
Temperature range
Maximum load
Reference spin speed
Programme description
(Type of load and soil level)
Washing programmes
Coton - Cotton
90°C - (Cold)
7 kg
1000 rpm
White cotton and coloured cotton. Nor-
mal, heavy and light soil.
Coton + Prélavage - Cotton
+ Prewash
90°C - (Cold)
7 kg
1000 rpm
White cotton and coloured cotton.
Heavy soil and normal soil.
Coton ECO - Cotton
ECO
1)
60°C - 40°C
7 kg
1000 rpm
White cotton and fast-coloured cotton.
Normal soil. The energy consumption de-
creases and the time of the washing pro-
gramme is extended, ensuring good wash-
ing results.
Synthétiques - Synthetics
60°C - (Cold)
3 kg
1000 rpm
Synthetic items or mixed fabric items.
Normal soil.
Mixte - Mix 20°
20°C
3 kg
1000 rpm
Special programme for cotton, synthetic and
mixed fabrics lightly soiled. Select this pro-
gramme to reduce the energy consumption.
Make sure that the detergent is suitable for
low temperatures in order to have good
washing results
2)
.
Délicats - Delicates
40°C - (Cold)
1.5 kg
700 rpm
Delicate fabrics such as acrylics, vis-
cose and mixed fabrics requiring gen-
tler washing. Normal soil.
Laine/Lavage à la main -
Wool/Handwash
40°C - (Cold)
1.5 kg
1000 rpm
Machine washable wool, hand washa-
ble wool and other fabrics with «hand
washing» care symbol
3)
.
Rinçage - Rinse
Cold
7 kg
1000 rpm
To rinse and spin the laundry. All fabrics,
except woollens and very delicate fabrics.
Reduce the spin speed accordingly to the
type of laundry.
6
Programme
Temperature range
Maximum load
Reference spin speed
Programme description
(Type of load and soil level)
Vidange - Drain
7 kg To drain the water in the drum. All fabrics.
Essorage - Spin
7 kg
1000 rpm
All fabrics, except woollens and deli-
cate fabrics. To spin the laundry and to
drain the water in the drum.
Repassage facile - Easy
Iron
60°C - (Cold)
1.5 kg
900 rpm
Synthetic items requiring a gentle
wash. Normal and light soil.
4)
Chemises - Shirts
30°C
900 rpm Synthetic and mixed fabric items. Light
soil items and items to freshen up. For 5 - 6
shirts.
Mini 30
30°C
3 kg
700 rpm
Synthetic and delicate items. Light soil
items or items to refresh.
Jeans
60°C - (Cold)
7 kg
1000 rpm
Items in denim and jersey. Also for dark
coloured items.
1) Standard programmes for the Energy Label consumption values. According to regulation
1061/2010, these programmes are respectively the «Standard 60°C cotton programme» and the «Stand-
ard 40°C cotton programme». They are the most efficient programmes in terms of combined energy and
water consumption for washing normally soiled cotton laundry.
The water temperature of the washing phase may differ from the temperature declared for the
selected programme.
2) The appliance performs the short heating phase if the water temperature is below 20°C. The appliance
can show the temperature setting as “cold”.
3) During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't
rotate or doesn't rotate properly, but this is normal for this programme.
4) To reduce creasing, this cycle regulates the water temperature and performs a soft wash and spin
phase. The appliance adds some rinses.
7
Programme options compatibility
Programme
Essorage - Spin
Anti-froissage
Rapide - Quick
1)
Rinçage plus
2)
Départ différé - Delay Start
Coton - Cotton
Coton + Prélavage - Cotton + Pre-
wash
Coton ECO - Cotton ECO
Synthétiques - Synthetics
Mixte - Mix 20°
Délicats - Delicates
Laine/Lavage à la main - Wool/Hand-
wash
Rinçage - Rinse
Vidange - Drain
Essorage - Spin
Repassage facile - Easy Iron
Chemises - Shirts
Mini 30
Jeans
1) If you set the shortest duration, we recommend that you decrease the load size. It is possible to fully
load the appliance, however the washing results can be less satisfactory.
2) If you set Extra Rinse option, the appliance adds some additional rinses. In the Rinse programme, if you
set a low spin speed the appliance performs delicate rinses and a short spin.
8
CONSUMPTION VALUES
Stated values are obtained in laboratory conditions with relevant standards. Different cau-
ses can change the data: the quantity and type of laundry and ambient temperature. Wa-
ter pressure, the supply voltage and the temperature of inlet water may also affect the
washing programme duration.
Technical specifications may be changed without prior notice to improve the quality of
product.
Programmes Load (kg)
Energy con-
sumption
(kWh)
Water con-
sumption (li-
tre)
Approximate
programme
duration (mi-
nutes)
Remaining
moisture (%)
1)
Coton - Cotton
60°C
7 1.41 79 230 60
Coton - Cotton
40°C
7 0.96 80 205 60
Synthétiques - Syn-
thetics 40°C
3 0.68 68 130 37
Délicats - Delicates
40°C
1.5 0.60 51 60 37
Laine/Lavage à la
main - Wool/Hand-
wash 30°C
2)
1.5 0.17 49 70 32
Standard cotton programmes
Standard 60°C cot-
ton
7 0.93 51 220 60
Standard 60°C cot-
ton
3.5 0.71 41 185 60
Standard 40°C cot-
ton
3.5 0.60 41 180 60
1) At the end of spin phase.
2) Not available for some models.
Off Mode (W) Left On Mode (W)
0.48 0.48
The information given in the chart above is compliant with the EU Commission regulation 1015/2010
implementing directive 2009/125/EC .
9
OPTIONS
TEMP.
With this option you can change the default
temperature.
Indicator = cold water.
The indicator of the set temperature comes on.
ESSORAGE - SPIN
With this button you can set one of these options:
The indicator of the set speed comes on.
Automatic spin reduction
Set this option to decrease the spin seed to a
half, but not less than 400 rpm.
Suitable for very delicate fabrics.
Rinse Hold
Set this option to prevent the laundry creases.
The drum turns regularly to prevent the laundry
creases.
There is a water in the drum when
the programme is completed. The
door stays locked. You must drain
the water to unlock the door. To
drain the water refer to ‘At the end
of the programme’.
RAPIDE - QUICK
Press this button to decrease the programme
duration.
Set this option for items with light soil or items to
refresh.
RINÇAGE PLUS
With this option you can add some rinses to a
washing programme.
Use this option for persons allergic to detergents
and in areas where the water is soft.
The related phase indicator on the control panel
comes on.
DÉPART DIFFÉRÉ - DELAY START
With this option you can delay the start of a
programme by 9, 6 or 3 hours.
SETTINGS
EXTRA RINSE
With this option you can permanently have an
extra rinse when you set a new programme.
To activate/deactivate this option touch the
buttons Essorage - Spin and Rapide - Quick
at the same time until the indicator Rinçage plus
comes on/goes off.
BEFORE FIRST USE
During installation or before first use
you may observe some water in the
appliance. This is residual water left in
the appliance after a full functional test
in the factory to ensure the appliance
is delivered to customers in perfect
working order and is no cause for
concern.
1. Connect the mains plug to the mains socket.
2. Open the water tap.
3. Put 2 litre of water in the detergent
compartment for washing phase.
This activates the drain system.
4. Put a small quantity of detergent in the
compartment for washing phase.
5. Set and start a programme for cotton at the
highest temperature without laundry.
This removes all possible dirt from the drum and the
tub.
10
DAILY USE
WARNING! Refer to Safety chapters.
LOADING THE LAUNDRY
Open the water tap. Connect the mains plug to the
mains socket.
1. Pull the door handle to open the appliance
door.
2. Put the laundry in the drum, one item at a time.
3. Shake the items before you put them in the
appliance.
Make sure not to put too much laundry in the drum.
Refer to max. loads indicated in "Programme chart".
4. Close the door.
CAUTION! Make sure that no laundry
stays between the seal and the door.
There is a risk of water leakage or
damage to the laundry.
Washing heavily oiled, greasy stains
could cause damage rubber parts of
the washing machine.
USING DETERGENT AND ADDITIVES
2
1
1. Measure out the de-
tergent and the fabric
conditioner.
2. Put the detergent
and the fabric condi-
tioner into the com-
partments.
3. Carefully close the
detergent drawer.
DETERGENT COMPARTMENTS
CAUTION! Use only specified
detergents for washing machine.
Always obey the instructions that you
find on the packaging of the detergent
products.
1 Detergent compartment for prewash
phase or soak programme (if availa-
ble). Add the detergent for prewash
and soak before the start of the pro-
gramme.
2 Detergent compartment for washing
phase. If you use a liquid detergent,
put it immediately before you start
the programme.
Compartment for liquid additives
(fabric conditioner, starch). Put the
product in the compartment before
you start the programme.
LIQUID OR POWDER DETERGENT
Pull out the detergent
dispenser until it stops.
A
2 1
The position A of the de-
tergent divider is for
powder detergent.
To use also liquid de-
tergent/additive or
bleach:
Remove detergent divider
from the position A.
11
B
Insert the detergent divid-
er in position B.
2 1
B
The position B of the de-
tergent divider is for pow-
der detergent in the rear
compartment and for liq-
uid detergent/additive or
bleach in the front com-
partment.
C
To use only liquid de-
tergent:
Insert the detergent divid-
er in position C.
2 1
C
The position C of the de-
tergent divider is for liq-
uid detergent.
Close the detergent dis-
penser carefully.
When you use the liquid detergent:
Do not use gelatinous or thick liq-
uid detergents.
Do not put more liquid detergent
than the edge of the detergent de-
vider.
Do not set the prewash option.
Do not set the delay start.
SETTING A PROGRAMME
1. Turn the programme knob to switch the
appliance on and set the programme:
The indicator of the button Départ/Pause - Start/
Pause flashes.
2. If necessary, change the temperature and the
spin speed or add available options.
When you activate an option, the indicator of the
set option comes on.
If you set something incorrect, the
indicator of button Départ/Pause -
Start/Pause flashes red.
STARTING A PROGRAMME WITHOUT THE
DELAY START
Press the button Départ/Pause - Start/Pause.
The corresponding indicator stops to flash.
The phase indicator illuminates and stays on.
The programme starts and the door locks.
The drain pump can operate for a
short time at the beginning of the
washing cycle.
STARTING A PROGRAMME WITH THE DELAY
START OPTION
1. Press the button Départ différé - Delay Start
repeatedly to set the required delay.
The indicator of the set delay comes on.
2. Press the button Départ/Pause - Start/Pause:
The door is locked.
The appliance starts the countdown.
When the countdown is completed, the
programme starts automatically.
You can cancel or change the delay
setting before you press the button
Départ/Pause - Start/Pause. After
pressing the button Départ/Pause -
Start/Pause, you can only cancel the
delay.
To cancel the delay start:
a. Press the button Départ/Pause - Start/
Pause to set the appliance to pause.
The corresponding indicator flashes.
b. Press the button Départ différé - Delay
Start once; the indicator of the set delay
goes off.
Press the button Départ/Pause - Start/
Pause again to start the programme
immediately.
12
INTERRUPTING A PROGRAMME AND
CHANGING THE OPTIONS
You can change only some options before they
operate.
1. Press the button Départ/Pause - Start/Pause.
The indicator flashes.
2. Change the options.
3. Press the button Départ/Pause - Start/Pause
again.
The programme continues.
CANCELLING A RUNNING PROGRAMME
1. Turn the programme knob to position to
cancel the programme and to deactivate the
appliance.
2. Turn the programme knob again to activate the
appliance. Now, you can set a new washing
programme.
Before starting the new programme
the appliance could drain the water. In
this case, make sure that the detergent
is still in the detergent compartment, if
not fill the detergent again.
OPENING THE DOOR
While a programme or the delay start operates, the
appliance door is locked.
CAUTION! If the temperature and
level of the water in the drum are too
high and the drum still rotates, you
cannot open the door.
To open the door during the first minutes of the
cycle or when the delay start operates:
1. Press the button Départ/Pause - Start/Pause
to pause the appliance.
2. Wait some minutes until the door unlocks.
3. You can open the door.
4. Close the door and touch the button Départ/
Pause - Start/Pause again. The programme (or
the delay) continues.
AT THE END OF THE PROGRAMME
The appliance stops automatically.
The indicator of the button Départ/Pause -
Start/Pause goes off. The phase indicator
illuminates and stays on.
Turn the programme knob to position to
deactivate the appliance.
After some minutes you can open the door.
Remove the laundry from the appliance. Make
sure that the drum is empty.
Close the water tap.
Keep the door and the detergent drawer ajar, to
prevent the mildew and odours.
The washing programme is completed, but
there is water in the drum:
The drum turns regularly to prevent the creases
in the laundry.
The indicator stays on.
The indicator Départ/Pause - Start/Pause
flashes to remind you to drain the water.
You must drain the water to open the door.
Draining the water:
1. Set a draining (Vidange - Drain) or a spinning
(Essorage - Spin) programme.
2. Press the button Départ/Pause - Start/Pause.
The appliance drains the water and spins.
3. When the programme is completed:
The indicator Départ/Pause - Start/Pause
goes off and the phase indicator
illuminates.
After some minutes the door unlocks; you
can now open the door.
4. Turn the programme knob to the position to
deactivate the appliance.
STAND BY
Some minutes after the end of the washing
programme, if you do not deactivate the appliance,
the energy saving status activates. The energy
saving status decreases the energy consumption
when the appliance is on the standby:
The brightness of the indicators reduces.
The indicator of the button Départ/Pause -
Start/Pause flashes slowly.
Press one of the buttons to deactivate the energy
saving status.
HINTS AND TIPS
THE LAUNDRY LOAD
Divide the laundry in: white, coloured,
synthetics, delicates and wool.
Obey the washing instructions that are on the
laundry care labels.
Do not wash white and coloured items together.
Some coloured items can discolour with the first
wash. We recommend that you wash them
separately for the first times.
Turn multilayered fabrics, wool and items with
painted illustrations inside out.
13
Remove hard stains with a special detergent.
Wash and pre-treat heavy soil stains before
putting items in drum
Be careful with the curtains. Remove the hooks
and put the curtains in a washing bag or
pillowcase.
Do not wash laundry without hems or with cuts.
Use a washing bag to wash small and/or
delicate items (e.g. underwired bras, belts,
tights, shoelaces, ribbons, etc. ).
A very small load can cause balance problems
with the spin phase. If this occurs, adjust
manually the items in the tub and start the spin
phase again.
Button up pillowcases, close zippers, hooks and
poppers. Tie up belts, cords, shoelaces, ribbons
and any other loose elements.
Empty the pockets and unfold the items.
STUBBORN STAINS
For some stains, water and detergent is not
sufficient.
We recommend that you pre-treat these stains
before you put the items in the appliance.
Special stain removers are available. Use the
special stain remover that is applicable to the type
of stain and fabric.
DETERGENTS AND ADDITIVES
Only use detergents and additives specially
made for washing machines:
powder detergents for all types of fabric,
powder detergents for delicate fabrics (40
°C max) and woollens,
liquid detergents, preferably for low
temperature wash programmes (60 °C max)
for all types of fabric, or special for woollens
only.
Do not mix different types of detergents.
To help the environment, do not use more than
the correct quantity of detergent.
Obey the instructions that you find on the on
packaging of these products.
Use the correct products for the type and colour
of the fabric, the programme temperature and
the level of soil.
If your appliance does not have the detergent
dispenser with the flap device, add the liquid
detergents with a dosing ball (supplied by the
detergent's manufacturer).
ECOLOGICAL HINTS
Set a programme without the prewash phase to
wash laundry with normal soil.
Always start a washing programme with the
maximum load of laundry allowed.
If necessary, use a stain remover when you set a
programme with a low temperature.
To use the correct quantity of detergent, check
the water hardness of your domestic system.
Refer to "Water hardness".
WATER HARDNESS
If the water hardness in your area is high or
moderate, we recommend that you use a water
softener for washing machines. In areas where the
water hardness is soft it is not necessary to use a
water softener.
To know the water hardness in your area, contact
your local water authority.
Use the correct quantity of the water softener.
Obey the instructions that you find on the
packaging of the product.
CARE AND CLEANING
WARNING! Refer to Safety chapters.
EXTERNAL CLEANING
Clean the appliance with soap and warm water
only. Fully dry all the surfaces.
CAUTION! Do not use alcohol,
solvents or chemical products.
DESCALING
If the water hardness in your area is high or
moderate, we recommend that you use a water
descaling product for washing machines.
Regularly examine the drum to prevent limescale
and rust particles.
To remove rust particles use only special products
for washing machines. Do this separately from the
laundry wash.
14
Always obey the instructions that you
find on the packaging of the product.
MAINTENANCE WASH
With the low temperature programmes it is possible
that some detergent stays in the drum. Perform a
maintenance wash regularly. To do this:
Remove all laundry from the drum.
Select the cotton programme with the highest
temperature with a small quantity of detergent.
DOOR SEAL
This appliance is designed with a self cleaning
draining system, allowing light fluff fibers that fall
off the clothes to be drained out with the water, in
such a way that there is no need to access this
area for regular maintenance and cleaning.
Regularly examine the seal and remove all objects
from the inner part. Coins, buttons, other small
items forgotten in the pockets of your clothes are
deposited during the washing cycle in the special
double lip trap in the porthole seal, where they can
be conveniently recovered at the end of the cycle.
CLEANING THE DETERGENT DISPENSER
1 2 3 4
5 6
CLEANING THE DRAIN FILTER
1 2 3 4
15
1
2
5 6 7 8
1
2
9 10
CLEANING THE INLET HOSE AND THE VALVE FILTER
1 2 3
45°
20°
4
EMERGENCY DRAIN
Because of a malfunction, the appliance cannot
drain the water.
If this occurs, do steps (1) through (10) of
'Cleaning the drain filter'. If necessary, clean the
pump.
When you drain the water with the emergency drain
procedure, you must activate again the drain
system:
1. When you drain the water with the emergency
drain procedure, you must activate again the
drain system: Put 2 litres of water in the main
wash compartment of the detergent dispenser.
2. Start the programme to drain the water
FROST PRECAUTIONS
If the appliance is installed in an area where the
temperature can be less than 0° C, remove the
remaining water from the inlet hose and the drain
pump.
1. Disconnect the mains plug from the mains
socket.
2. Close the water tap.
3. Put the two ends of the inlet hose in a
container and let the water flow out of the
hose.
4. Empty the drain pump. Refer to the emergency
drain procedure.
5. When the drain pump is empty, install the inlet
hose again.
WARNING! Make sure that the
temperature is higher than 0 °C before
you use the appliance again.
The manufacturer is not responsible
for damages caused by low
temperatures.
16
TROUBLESHOOTING
WARNING! Refer to Safety chapters.
INTRODUCTION
The start of the appliance does not occur or it
stops during operation.
First try to find a solution to the problem (refer to
the table). If not, contact the Authorised Service
Centre.
With some problems, the acoustic signals operate.
The red indicator of the button Départ/Pause -
Start/Pause flashes and one of the phase indicators
comes on, to show an alarm code:
- The appliance does not fill with water
properly.
- The appliance does not drain the water.
- The appliance door is open or not closed
correctly. Please check the door!
The indicator of button Départ/Pause - Start/
Pause flashes in red 11 times and 1 (or 2 or 3)
time(s) in green: the mains supply is unstable.
Wait until the mains supply is stable and the
appliance automatically starts operating.
WARNING! Deactivate the appliance
before you do the checks.
POSSIBLE FAILURES
Problem Possible solution
The programme does not
start.
Make sure that the mains plug is connected to the mains socket.
Make sure that the appliance door is closed.
Make sure that there is not a damaged fuse in the fuse box.
Make sure that the Start/Pause has been pressed.
If the delay start is set, cancel the setting or wait for the end of
countdown.
Deactivate the Child Lock function if it is on (if available).
The appliance does not fill
with water properly.
Make sure that the water tap is open.
Make sure that the pressure of the water supply is not too low. For
this information, contact your local water authority.
Make sure that the water tap is not clogged.
The appliance does not
drain the water.
Make sure that the sink spigot is not clogged.
Make sure that the drain hose has no kinks or bends.
Make sure that the drain filter is not clogged. Clean the filter, if nec-
essary. Refer to 'Care and cleaning'.
Make sure that the drain hose is in the correct position. The hose
may be too low.
Set the drain programme if you set a programme without drain
phase.
Set the drain programme if you set an option which ends with water
in the tub.
The spin phase does not
operate or the washing cy-
cle lasts longer than usual-
ly.
Set the spin programme.
Adjust manually the items in the tub and start the spin phase again.
This problem may be caused by balance problems.
There is water on the floor. Make sure that the couplings of the water hoses are tight and there
is not water leakages.
Make sure that the drain hose have no damages.
Make sure you use the correct detergent and the correct quantity of
it.
17
Problem Possible solution
You cannot open the appli-
ance door.
Make sure that the washing programme is finished.
Set the drain or the spin programme if there is water in the drum.
The appliance makes an
unusual noise.
Make sure the levelling of the appliance is correct. Refer to 'Installa-
tion'.
Make sure that the packaging and/or the transit bolts are removed.
Refer to 'Installation'.
Add more laundry in the drum. The load may be too small.
The washing results are
not satisfactory.
Increase the detergent quantity or use a different detergent.
Use special products to remove the stubborn stains before you
wash the laundry.
Make sure that you set the correct temperature.
Decrease the laundry load.
You cannot set an option. Make sure that you press only the wanted button(s).
After the check, activate the appliance. The
programme continues from the point of interruption.
If the problem occurs again, contact the Authorised
Service Centre.
SERVICE
We recommend the use of original spare parts.
When contacting the Authorised Service Centre,
make sure that these data are available. You can
find the information on the rating plate: model, PNC
and Serial Number. (Mod., Prod. No., Ser. No.)
TECHNICAL DATA
Dimension Width/ Height/ Depth/ To-
tal depth
595 mm / 850 mm / 450 mm / 490 mm
Electrical connection Voltage
Overall power
Fuse
Frequency
220-240 V
2200 W
10 A
50 Hz
Level of protection against ingress of solid particles and
moisture ensured by the protective cover, except where
the low voltage equipment has no protection against
moisture
IPX4
Water supply pressure Minimum
Maximum
0.5 bar (0.05 MPa)
8 bar (0.8 MPa)
Water supply
1) Cold water
Maximum Load Cotton 7 kg
Energy Efficiency Class A++
Spin Speed Maximum 1000 rpm
1) Connect the water inlet hose to a water tap with a 3/4'' thread.
18
ENVIRONMENTAL CONCERNS
Recycle materials with the symbol . Put the
packaging in relevant containers to recycle it. Help
protect the environment and human health by
recycling waste of electrical and electronic
appliances. Do not dispose of appliances marked
with the symbol with the household waste.
Return the product to your local recycling facility or
contact your municipal office.
19
INFORMATIONS DE SÉCURITÉ
Avant d'installer et d'utiliser cet appareil, lisez soigneusement les
instructions fournies. Le fabricant ne pourra être tenu pour
responsable des blessures et dégâts résultant d'une mauvaise
installation ou utilisation. Conservez toujours les instructions dans
un lieu sûr et accessible pour vous y référer ultérieurement.
SÉCURITÉ DES ENFANTS ET DES PERSONNES
VULNÉRABLES
Cet appareil peut être utilisé par des enfants de plus de 8 ans,
ainsi que des personnes dont les capacités physiques,
sensorielles et mentales sont réduites ou dont les
connaissances et l'expérience sont insuffisantes, à condition
d'être surveillés ou d'avoir reçu des instructions concernant
l'utilisation sécurisée de l'appareil et de comprendre les risques
encourus.
Les enfants entre 3 et 8 ans et les personnes ayant un
handicap très important et complexe doivent être tenus à l'écart
de l'appareil, à moins d'être surveillés en permanence.
Les enfants de moins de 3 ans doivent être tenus à l'écart de
l'appareil, à moins d'être surveillés en permanence.
Ne laissez pas les enfants jouer avec l'appareil.
Ne laissez pas les emballages à la portée des enfants et jetez-
les convenablement.
Ne laissez pas les détergents à la portée des enfants.
Tenez les enfants et les animaux éloignés de l'appareil lorsque
la porte est ouverte.
Les enfants ne doivent pas nettoyer ni entreprendre une
opération de maintenance sur l'appareil sans surveillance.
SÉCURITÉ GÉNÉRALE
Ne modifiez pas les caractéristiques de cet appareil.
Cet appareil est conçu uniquement pour un usage domestique
et des situations telles que :
dans des cuisines réservées aux employés dans des
magasins, bureaux et autres lieux de travail ;
20
1 / 1

Zanussi ZWS76100WW Manuel utilisateur

Catégorie
Machines à laver
Taper
Manuel utilisateur

dans d''autres langues