Hilti SID 2-A12 Guide d'installation

SID 2A12

English 1

Français 14

Español 28

Português 42

Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00

1

Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00

2

3

4

5

Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00

SID 2A12

en Original operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . 1

fr Notice d'utilisation originale . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

es Manual de instrucciones original . . . . . . . . . . . . . . . . . . . . . . . 28

pt Manual de instruções original . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00

*2235359*

2235359 English 1

1 Information about the documentation

1.1 About this documentation

• Read this documentation before initial operation or use. This is a

prerequisite for safe, trouble-free handling and use of the product.

• Observe the safety instructions and warnings in this documentation and

on the product.

• Always keep the operating instructions with the product and make sure

that the operating instructions are with the product when it is given to

other persons.

1.2 Explanation of symbols used

1.2.1 Warnings

Warnings alert persons to hazards that occur when handling or using the

product. The following signal words are used:

DANGER

DANGER !

▶ Draws attention to imminent danger that will lead to serious personal

injury or fatality.

WARNING

WARNING !

▶ Draws attention to a potential threat of danger that can lead to serious

injury or fatality.

CAUTION

CAUTION !

▶ Draws attention to a potentially dangerous situation that could lead to

slight personal injury or damage to the equipment or other property.

1.2.2 Symbols in the documentation

The following symbols are used in this document:

Read the operating instructions before use.

Instructions for use and other useful information

Dealing with recyclable materials

Do not dispose of electric equipment and batteries as household

waste

1.2.3 Symbols in the illustrations

The following symbols are used in illustrations:

Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00

2 English 2235359

*2235359*

These numbers refer to the corresponding illustrations found at the

beginning of these operating instructions

The numbering reflects the sequence of operations shown in the

illustrations and may deviate from the steps described in the text

Item reference numbers are used in the overview illustrations and

refer to the numbers used in the product overview section

This symbol is intended to draw special attention to certain points

when handling the product.

1.3 Product-dependent symbols

1.3.1 Symbols on the product

The following symbols can be used on the product:

The power tool supports near-field communication (NFC) technol-

ogy, which is compatible with iOS and Android platforms.

Li-ion battery

Hilti Li-ion battery type series used. Observe the information given in

the section headed Intended use.

Never use the battery as a striking tool.

Do not drop the battery. Never use a battery that has suffered an

impact or is damaged in any other way.

Direct current (DC)

Rated speed

Forward rotation

Reverse rotation

1.4 Product information

products are designed for professional users and only trained,

authorized personnel are permitted to operate, service and maintain the

products. This personnel must be specifically informed about the possible

hazards. The product and its ancillary equipment can present hazards if

used incorrectly by untrained personnel or if used not in accordance with

the intended use.

The type designation and serial number are printed on the rating plate.

Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00

*2235359*

2235359 English 3

▶ Write down the serial number in the table below. You will be required to

state the product details when contacting Hilti Service or your local Hilti

organization to inquire about the product.

Product information

Type: SID 2-A12

Generation: 02

Serial no.:

1.5 Declaration of conformity

We declare, on our sole responsibility, that the product described here

complies with the applicable directives and standards. A copy of the

declaration issued by the certification department can be found at the end

of this documentation.

The technical documentation is filed here:

Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916

Kaufering, Germany

2 Safety

2.1 General power tool safety warnings

WARNING Read all safety warnings, instructions, illustrations and

specifications provided with this power tool. Failure to follow all instruc-

tions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded)

power tool or battery-operated (cordless) power tool.

Work area safety

▶ Keep work area clean and well lit. Cluttered or dark areas invite

accidents.

▶ Do not operate power tools in explosive atmospheres, such as in

the presence of flammable liquids, gases or dust. Power tools create

sparks which may ignite the dust or fumes.

▶ Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

Electrical safety

▶ Power tool plugs must match the outlet. Never modify the plug in any

way. Do not use any adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will reduce risk of electric

shock.

▶ Avoid body contact with earthed or grounded surfaces, such as

pipes, radiators, ranges and refrigerators. There is an increased risk of

electric shock if your body is earthed or grounded.

Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00

4 English 2235359

*2235359*

▶ Do not expose power tools to rain or wet conditions. Water entering a

power tool will increase the risk of electric shock.

▶ Do not abuse the cord. Never use the cord for carrying, pulling or

unplugging the power tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled cords increase the risk

of electric shock.

▶ When operating a power tool outdoors, use an extension cord suitable

for outdoor use. Use of a cord suitable for outdoor use reduces the risk

of electric shock.

▶ If operating a power tool in a damp location is unavoidable, use

a residual current device (RCD) protected supply. Use of an RCD

reduces the risk of electric shock.

Personal safety

▶ Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired

or under the influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in serious personal

injury.

▶ Use personal protective equipment. Always wear eye protection.

Protective equipment such as a dust mask, non-skid safety shoes, hard

hat or hearing protection used for appropriate conditions will reduce

personal injuries.

▶ Prevent unintentional starting. Ensure the switch is in the off-position

before connecting to power source and/or battery pack, picking up

or carrying the tool. Carrying power tools with your finger on the switch

or energising power tools that have the switch on invites accidents.

▶ Remove any adjusting key or wrench before turning the power tool

on. A wrench or a key left attached to a rotating part of the power tool

may result in personal injury.

▶ Do not overreach. Keep proper footing and balance at all times. This

enables better control of the power tool in unexpected situations.

▶ Dress properly. Do not wear loose clothing or jewellery. Keep your

hair, clothing and gloves away from moving parts. Loose clothes,

jewellery or long hair can be caught in moving parts.

▶ If devices are provided for the connection of dust extraction and

collection facilities, ensure these are connected and properly used.

Use of dust collection can reduce dust-related hazards.

▶ Do not let familiarity gained from frequent use of tools allow you

to become complacent and ignore tool safety principles. A careless

action can cause severe injury within a fraction of a second.

Power tool use and care

▶ Do not force the power tool. Use the correct power tool for your

application. The correct power tool will do the job better and safer at the

rate for which it was designed.

Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00

*2235359*

2235359 English 5

▶ Do not use the power tool if the switch does not turn it on and off.

Any power tool that cannot be controlled with the switch is dangerous

and must be repaired.

▶ Disconnect the plug from the power source and/or remove the

battery pack, if detachable, from the power tool before making

any adjustments, changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting the power tool

accidentally.

▶ Store idle power tools out of the reach of children and do not

allow persons unfamiliar with the power tool or these instructions

to operate the power tool. Power tools are dangerous in the hands of

untrained users.

▶ Maintain power tools and accessories. Check for misalignment or

binding of moving parts, breakage of parts and any other condition

that may affect the power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents are caused by poorly

maintained power tools.

▶ Keep cutting tools sharp and clean. Properly maintained cutting tools

with sharp cutting edges are less likely to bind and are easier to control.

▶ Use the power tool, accessories and tool bits etc. in accordance with

these instructions, taking into account the working conditions and

the work to be performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

▶ Keep handles and grasping surfaces dry, clean and free from oil and

grease. Slippery handles and grasping surfaces do not allow for safe

handling and control of the tool in unexpected situations.

Battery tool use and care

▶ Recharge only with the charger specified by the manufacturer. A

charger that is suitable for one type of battery pack may create a risk of

fire when used with another battery pack.

▶ Use power tools only with specifically designated battery packs. Use

of any other battery packs may create a risk of injury and fire.

▶ When battery pack is not in use, keep it away from other metal

objects, like paper clips, coins, keys, nails, screws or other small

metal objects, that can make a connection from one terminal to

another. Shorting the battery terminals together may cause burns or a

fire.

▶ Under abusive conditions, liquid may be ejected from the battery;

avoid contact. If contact accidentally occurs, flush with water. If

liquid contacts eyes, additionally seek medical help. Liquid ejected

from the battery may cause irritation or burns.

▶

Do not use a battery pack or tool that is damaged or modified.

Damaged or modified batteries may exhibit unpredictable behaviour

resulting in fire, explosion or risk of injury.

Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00

6 English 2235359

*2235359*

▶ Do not expose a battery pack or tool to fire or excessive temperature.

Exposure to fire or temperature above 130° C (265 °F) may cause

explosion.

▶ Follow all charging instructions and do not charge the battery pack

or tool outside the temperature range specified in the instructions.

Charging improperly or at temperatures outside the specified range may

damage the battery and increase the risk of fire.

Service

▶ Have your power tool serviced by a qualified repair person using only

identical replacement parts. This will ensure that the safety of the power

tool is maintained.

▶ Never service damaged battery packs. Service of battery packs should

only be performed by the manufacturer or authorized service providers.

2.2 Drill/driver safety warnings

▶ Hold the power tool by insulated gripping surfaces, when performing

an operation where the fastener may contact hidden wiring. Fasteners

contacting a "live" wire may make exposed metal parts of the power tool

"live" and could give the operator an electric shock.

2.3 Additional safety instructions

Personal safety

▶ Use the product only when it is in perfect working order.

▶ Never tamper with or modify the tool in any way.

▶ Do not look directly into the light source (LEDs) integrated in the drill/driver

and do not direct the light at other persons’ faces. This presents a risk of

dazzling or eye damage.

▶ Avoid touching rotating parts. Switch the power tool on only after bringing

it into position at the workpiece. Touching rotating parts, especially

rotating accessory tools, may lead to injury.

▶ Wear protective gloves also when changing the accessory tool. Touching

the accessory tool presents a risk of injury (cuts or burns).

▶ Always hold the tool securely by the grip. If the accessory tool (e.g. the

drill bit) sticks and stalls, the power tool, due to its high torque, may

tend to rotate about its own axis in the direction opposite to that of the

accessory tool.

▶ Make sure that the workplace is well ventilated and, where necessary,

wear a respirator appropriate for the type of dust generated. Contact with

or inhalation of the dust may cause allergic reactions and/or respiratory

or other diseases to the operator or bystanders. Certain kinds of dust

are classified as carcinogenic such as oak and beech dust, especially

in conjunction with additives for wood conditioning (chromate, wood

preservative). Material containing asbestos may be handled only by

specialists.

Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00

*2235359*

2235359 English 7

▶ Take breaks and exercise your fingers to improve the blood circulation.

Exposure to vibration during long periods of work can lead to disorders

of the blood vessels and nervous system in the fingers, hands and wrists.

Electrical safety

▶ Before beginning work, check the working area for concealed electric

cables or gas and water pipes. External metal parts of the power tool may

give you an electric shock if you damage an electric cable accidentally.

Power tool use and care

▶ Secure the workpiece. Use clamps or a vice to hold the workpiece in

position. The workpiece is thus held more securely than by hand and both

hands remain free to operate the power tool.

▶ Immediately switch off the power tool if the accessory tool jams. The

power tool might twist off-line.

▶ Wait until the power tool stops completely before you lay it down.

2.4 Battery use and care

▶ Observe the special regulations and instructions applicable to the trans-

port, storage and use of Li-ion batteries.

▶ Do not expose batteries to high temperatures, direct sunlight or fire.

▶ Do not disassemble, crush or incinerate batteries and do not subject them

to temperatures over 80 °C.

▶ Do not use or charge batteries that have suffered mechanical impact,

have been dropped from a height or show signs of damage. In this case,

always contact your Hilti Service.

▶ If the battery is too hot to touch it may be defective. In this case, place the

product in a non-flammable location, well away from flammable materials,

where it can be kept under observation and allowed to cool down. In this

case, always contact your Hilti Service.

3 Description

3.1 Product overview 1

@

Forward / reverse switch

;

Grip

=

Illumination

%

Belt hook (optional)

&

Battery state of charge indica-

tor

(

Battery release button

)

Control switch

+

Hex. socket

3.2 Intended use

The product described is a hand-held cordless impact screwdriver. It is

designed for tightening and releasing nuts, bolts, anchors and wood screws.

Use the cordless screwdriver only for applications that do not require a

precise/specified torque.

Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00

8 English 2235359

*2235359*

▶ Use only Hilti LiIon batteries of the B 12 series with this product.

▶ Use only Hilti battery chargers of the C4/12 series for charging these

batteries.

3.3 Charge state display

The charge state of the Liion battery is displayed after pressing one of the

release buttons lightly (press only until slight resistance is felt).

Status Meaning

4 LEDs light. Charge state: 75 % to 100 %

3 LEDs light. Charge state: 50 % to 75 %

2 LEDs light. Charge state: 25 % to 50 %

1 LED lights. Charge state: 10 % to 25 %

1 LED blinks. Charge state: < 10 %

Battery charge state cannot be displayed while the control switch is

pressed and for up to 5 seconds after releasing the control switch.

3.4 Items supplied

Impact screwdriver/wrench, operating instructions.

Spare parts, consumables and accessories approved by Hilti for use

with the product can be found at your local Hilti Store or online at:

www.hilti.group

4 Technical data

4.1 Technical data

SID 2A12

Rated voltage

10.8 V

Weight

1.1 kg

(2.4 lb)

Rated speed under no load

0 /min …

2,750 /min

Ambient temperature for operation

−17 ℃ … 60 ℃

(1 ℉ … 140 ℉)

Storage temperature

−20 ℃ … 70 ℃

(−4 ℉ … 158 ℉)

Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00

*2235359*

2235359 English 9

4.2 Battery

Battery operating voltage

10.8 V

Ambient temperature for operation

−17 ℃ … 60 ℃

(1 ℉ … 140 ℉)

Storage temperature

−20 ℃ … 40 ℃

(−4 ℉ … 104 ℉)

Battery charging starting temperature

−10 ℃ … 45 ℃

(14 ℉ … 113 ℉)

5 Preparations at the workplace

CAUTION

Risk of injury by inadvertent starting!

▶ Before inserting the battery, make sure that the product is switched off.

▶ Remove the battery before making any adjustments to the power tool or

before changing accessories.

Observe the safety instructions and warnings in this documentation and on

the product.

5.1 Charging the battery

1. Before charging the battery, read the operating instructions for the

charger.

2. Make sure that the contacts on the battery and the contacts on the

charger are clean and dry.

3. Use an approved charger to charge the battery.

5.2 Inserting the battery

CAUTION

Risk of injury by short circuit or falling battery!

▶ Before inserting the battery, make sure that the contacts on the battery

and the contacts on the product are free of foreign matter.

▶ Make sure that the battery always engages correctly.

1. Charge the battery fully before using it for the first time.

2. Push the battery into the battery holder until it engages with an audible

click.

3. Check that the battery is seated securely.

5.3 Removing the battery

1. Press the battery release buttons.

2. Remove the battery from the tool.

Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00

10 English 2235359

*2235359*

5.4 Fitting the belt hook (optional) 2

CAUTION

Risk of injury by falling power tools!

▶ Check that the belt hook is fitted securely before beginning work.

The belt hook enables you to attach suitable power tools to your belt, where

they are close to your body. It can be fitted to allow attachment on the left

or right side of the body.

1. Remove the battery from the power tool.

2. Secure the belt hook with 2 screws to the base of the power tool.

3. Check that belt hook and power tool are secure.

6 Types of work

ATTENTION

Risk of damage by incorrect handling!

▶ Do not operate the switches for direction of rotation and/or function

selection during operation.

Observe the safety instructions and warnings in this documentation and on

the product.

6.1 Fitting the accessory tool 4

1. Set the forward/reverse switch to the middle position or remove the

battery from the power tool.

2. Insert the accessory tool into the chuck.

3. Check that the accessory tool is held securely.

6.2 Setting forward or reverse rotation 3

An interlock prevents switching while the motor is running.

The control switch is locked when the forward/reverse switch is in the

middle position (safety lock).

▶ Set the forward/reverse switch to the desired direction of rotation.

6.3 Switching on

▶ Press the control switch.

➥ Speed of rotation is regulated by the distance the control switch is

pressed in.

6.4 Switching off

▶ Release the control switch.

Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00

*2235359*

2235359 English 11

6.5 Removing the accessory tool 5

1. Set the forward/reverse switch to the middle position or remove the

battery from the power tool.

2. Pull the accessory tool out of the chuck.

7 Care and maintenance

WARNING

Risk of injury with battery inserted !

▶ Always remove the battery before carrying out care and maintenance

tasks!

Care and maintenance of the tool

• Carefully remove stubborn dirt.

• Clean the air vents carefully with a dry brush.

• Use only a slightly damp cloth to clean the casing. Do not use cleaning

agents containing silicone as these can attack the plastic parts.

Care of the Liion batteries

• Keep the battery free from oil and grease.

• Use only a slightly damp cloth to clean the casing. Do not use cleaning

agents containing silicone as these may attack the plastic parts.

• Avoid ingress of moisture.

Maintenance

• Check all visible parts and controls for signs of damage at regular intervals

and make sure that they all function correctly.

• Do not operate the product if signs of damage are found or if parts

malfunction. Have it repaired immediately by Hilti Service.

• After cleaning and maintenance, fit all guards or protective devices and

check that they function correctly.

To help ensure safe and reliable operation, use only genuine Hilti spare

parts and consumables. Spare parts, consumables and accessories

approved by Hilti for use with the product can be found at your local

Hilti Store or online at: www.hilti.group.

8 Transport and storage of cordless tools

Transport

CAUTION

Accidental starting during transport !

▶ Always transport your products with the batteries removed!

▶ Remove the battery.

▶ Never transport batteries in bulk form (loose, unprotected).

Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00

12 English 2235359

*2235359*

▶ Check the tool and batteries for damage before use after long periods of

transport.

Storage

CAUTION

Accidental damage caused by defective or leaking batteries !

▶ Always store your products with the batteries removed!

▶ Store the tool and batteries in a place that is as cool and dry as possible.

▶ Never store batteries in direct sunlight, on heating units or behind a

window pane.

▶ Store the tool and batteries in a place where they cannot be accessed by

children or unauthorized persons.

▶ Check the tool and batteries for damage before use after long periods of

storage.

9 Troubleshooting

If the trouble you are experiencing is not listed in this table or you are unable

to remedy the problem by yourself, please contact Hilti Service.

Trouble or fault Possible cause Action to be taken

The power tool does

not work.

The battery is not fully

inserted.

▶ Insert the battery.

→ page 9

The control switch

cannot be pressed,

or is stuck.

The forward/reverse

selector switch is in the

middle position.

▶ Set the

forward/reverse

switch to the desired

position. → page 10

Running speed sud-

denly drops consid-

erably.

Low battery. ▶ Charge the battery.

→ page 9

The battery runs

down more quickly

than usual.

Very low ambient tem-

perature.

▶ Allow the battery to

warm up slowly to

room temperature.

The battery doesn’t

engage with an audi-

ble click.

The retaining lugs on the

battery are dirty.

▶ Clean the retaining

lugs and engage the

battery in the working

position.

The power tool or

the battery becomes

very warm.

Electrical fault. ▶ Switch the power

tool off immediately,

remove the battery,

keep it under obser-

vation, allow it to cool

down and contact

Hilti Service.

Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00

*2235359*

2235359 English 13

Trouble or fault Possible cause Action to be taken

The power tool or

the battery becomes

very warm.

The tool is overloaded

(application limits ex-

ceeded).

▶ Select a suitable

power tool for the

application.

10 Disposal

Most of the materials from which Hilti tools and appliances are manu-

factured can be recycled. The materials must be correctly separated before

they can be recycled. In many countries, your old tools, machines or appli-

ances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti

representative for further information.

▶ Do not dispose of power tools, electronic equipment or batteries as

household waste!

11 Manufacturer’s warranty

▶ Please contact your local Hilti representative if you have questions about

the warranty conditions.

Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00

14 Français 2235359

*2235359*

1 Indications relatives à la documentation

1.1 À propos de cette documentation

• Lire intégralement la présente documentation avant la mise en service.

C'est la condition préalablement requise pour assurer la sécurité du travail

et un maniement sans perturbations.

• Bien respecter les consignes de sécurité et les avertissements de la

présente documentation ainsi que celles figurant sur le produit.

• Toujours conserver le mode d'emploi à proximité du produit et uniquement

le transmettre à des tiers avec ce mode d'emploi.

1.2 Explication des symboles

1.2.1 Avertissements

Les avertissements attirent l'attention sur des dangers liés à l'utilisation du

produit. Les termes de signalisation suivants sont utilisés :

DANGER

DANGER !

▶ Pour un danger imminent qui peut entraîner de graves blessures corpo-

relles ou la mort.

AVERTISSEMENT

AVERTISSEMENT !

▶ Pour un danger potentiel qui peut entraîner de graves blessures corpo-

relles ou la mort.

ATTENTION

ATTENTION !

▶ Pour attirer l'attention sur une situation pouvant présenter des dangers

entraînant des blessures corporelles légères ou des dégâts matériels.

1.2.2 Symboles dans la documentation

Les symboles suivants sont utilisés dans la présente documentation :

Lire le mode d'emploi avant d'utiliser l'appareil

Pour des conseils d'utilisation et autres informations utiles

Maniement des matériaux recyclables

Ne pas jeter les appareils électriques et les accus dans les ordures

ménagères

1.2.3 Symboles dans les illustrations

Les symboles suivants sont utilisés dans les illustrations :

Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00

*2235359*

2235359 Français 15

Ces chiffres renvoient à l'illustration correspondante au début du

présent mode d'emploi

La numérotation détermine la séquence des étapes de travail dans

l'image et peut se différencier de celles des étapes de travail dans le

texte

Les numéros de position sont utilisés dans l'illustration Vue d’en-

semble et renvoient aux numéros des légendes dans la section Vue

d'ensemble du produit

Ce signe doit inviter à manier le produit en faisant particulièrement

attention.

1.3 Symboles spécifiques au produit

1.3.1 Symboles sur le produit

Les symboles suivants peuvent être utilisés sur le produit :

L'appareil prend en charge la technologie qui est compatible avec

les plates-formes iOS et Android.

Accu lithium-ions

Série de type d'accu Li-Ion Hilti utilisée. Observer les instructions au

chapitre Utilisation conforme à l'usage prévu.

Ne jamais utiliser l'accu comme outil de percussion.

Ne pas laisser tomber l'accu. Ne pas utiliser d'accu ayant subi un

choc ou d'autres dommages.

Courant continu

Vitesse de rotation de référence

Rotation droite

Rotation gauche

1.4 Informations produit

Les produits sont destinés aux professionnels et ne doivent

être utilisés, entretenus et réparés que par un personnel autorisé et formé.

Ce personnel doit être spécialement instruit quant aux dangers inhérents

à l'utilisation de l'appareil. Le produit et ses accessoires peuvent s'avérer

dangereux s'ils sont utilisés de manière incorrecte par un personnel non

qualifié ou de manière non conforme à l'usage prévu.

La désignation du modèle et le numéro de série figurent sur sa plaque

signalétique.

Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00

16 Français 2235359

*2235359*

▶ Inscrivez le numéro de série dans le tableau suivant. Les informations

produit vous seront demandées lorsque vous contactez nos revendeurs

ou services après-vente.

Caractéristiques produit

Type : SID 2-A12

Génération : 02

N° de série :

1.5 Déclaration de conformité

Nous déclarons sous notre seule et unique responsabilité que le produit

décrit ici est conforme aux directives et normes en vigueur. Une copie de

l'attestation délivrée par l'organisme de certification se trouve en fin de la

présente documentation.

Pour obtenir les documentations techniques, s'adresser à :

Hilti Entwicklungsgesellschaft mbH | Zulassung Geräte | Hiltistraße 6 | 86916

Kaufering, DE

2 Sécurité

2.1 Indications générales de sécurité pour les appareils électriques

AVERTISSEMENT Lire toutes les consignes de sécurité et instruc-

tions, illustrations et caractéristiques techniques, qui accompagnent

cet outil électroportatif. Tout manquement à l'observation des instruc-

tions suivantes risque de provoquer une électrocution, un incendie et/ou de

graves blessures.

Les consignes de sécurité et instructions doivent être intégralement

conservées pour les utilisations futures.

La notion d'« outil électroportatif » mentionnée dans les consignes de

sécurité se rapporte à des outils électriques raccordés au secteur (avec

câble d'alimentation) et à des outils électriques sur accu (sans câble

d'alimentation).

Sécurité sur le lieu de travail

▶ Conserver la zone de travail propre et bien éclairée. Un lieu de travail

en désordre ou mal éclairé augmente le risque d'accidents.

▶ Ne pas faire fonctionner les outils électriques en atmosphère ex-

plosive et où se trouvent des liquides, des gaz ou poussières in-

flammables. Les outils électriques produisent des étincelles qui peuvent

enflammer les poussières ou les fumées.

▶ Maintenir les enfants et les personnes présentes à l'écart pendant

l'utilisation de l'outil électroportatif. En cas d'inattention il y a risque de

perdre le contrôle de l'appareil.

Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00

La page charge ...

Hilti SID 2-A12 Guide d'installation

Ce manuel convient également à

Hilti SID 2-A12 Guide d'installation

dans d''autres langues

Documents connexes